Scribd
Upload
121 views2 pages

Moshell+Bss Command

This document provides instructions for performing various monitoring and troubleshooting tasks on a mobile network. Some of the key tasks outlined include: 1. Checking for critical alarms by specifying an alarm priority list. 2. Checking the BCCH frequency of a cell. 3. Getting a list of all sites in a base station controller. 4. Checking the frequency, hopping status, and GPRS configuration of a specific site. 5. Checking traffic levels and signalling status through various monitoring commands.

Uploaded by

Pralad Raj Baral
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
121 views2 pages

Moshell+Bss Command

This document provides instructions for performing various monitoring and troubleshooting tasks on a mobile network. Some of the key tasks outlined include: 1. Checking for critical alarms by specifying an alarm priority list. 2. Checking the BCCH frequency of a cell. 3. Getting a list of all sites in a base station controller. 4. Checking the frequency, hopping status, and GPRS configuration of a specific site. 5. Checking traffic levels and signalling status through various monitoring commands.

Uploaded by

Pralad Raj Baral
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

lt all cvls cvms cvcu 1.

To check the critical alarms: allip:acl=a1;For site downs and critical alarms allip:acl=a2;For major alarms allip:acl=a3;For minor alarms 2. To check BCCH Frequency: rldep:cell= cellname; 3. To get the list of all the sites in the BSC: rldep:cell=all; 4. To check the frequency of a site: rlcfp:cell=cellname; 5. To check if hopping is enabled or not: rlchp:cell=cellname; 6.To check if GPRS is enabled or not: rlgsp:cell=cellname; 7.To check the traffic: rxtcp:moty=rxotg,cell=cellname;(get TG value) rxmsp:mo=rxocf-TG No,subord; 8.Signalling and status of channel configuration: rlcrp:cell=cellname; 9. To lock the site rxbli:mo=rxocf-TG /CF No.,subord,force; To unlock the site rxble:mo=rxocf-TG /CF No.,subord; 10. To lock the TRX rxbli:mo=rxotrx-TG /CF No.-trx.No.,subord,force; To unlock the TRX rxble:mo=rxotrx-TG /CF No.-trx.No.,subord;

11. To lock the time slot: rxbli:mo=rxotrx-TG /CF No.-trx.No-Ts No,subord,force; To unlock the time slot rxble:mo=rxotrx-TG /CF No.-trx.No-Ts No,subord; 12. To find the Dip (ET) Status: rxtcp:moty=rxotg,cell=cellname;(Get the TG value) rxapp:mo=rxotg-TG No.(Get the RBLT value) radep:dev=rblt-RBLT No;(Get the SNT value) ntcop:snt=etrblt-SNT No;(Get the DIP No) dtstp:dip=DIP No.; 13. To check configuration of the site:

rxmop:mo=rxotr-CF No-0&&-TRX No.; 14. To find the BTS internal alarms: rxmfp:mo=rxocf-CF No; rxmfp:mo=rxotrx-CF No-TRX No; 15. To refresh BTS through software: rxese:mo=rxocf-CF No,subord;

You might also like