Scribd
Upload
533 views9 pages

How To Use The ETL MC68HC908AZ60 FLASH /EERPOM PROGRAMMER (Practice Test)

This document provides instructions for using an MC68HC908AZ60 FLASH/EEPROM programmer to program an MC68HC05H12 microcontroller. It describes connecting the programmer to the target microcontroller, starting the programming software, selecting device and programming options, reading data from the microcontroller, viewing the results, and lifting a pin from the explorer board before beginning programming. Caution is advised, and reviewing the user manual is recommended before attempting this procedure.

Uploaded by

dongvac
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
533 views9 pages

How To Use The ETL MC68HC908AZ60 FLASH /EERPOM PROGRAMMER (Practice Test)

This document provides instructions for using an MC68HC908AZ60 FLASH/EEPROM programmer to program an MC68HC05H12 microcontroller. It describes connecting the programmer to the target microcontroller, starting the programming software, selecting device and programming options, reading data from the microcontroller, viewing the results, and lifting a pin from the explorer board before beginning programming. Caution is advised, and reviewing the user manual is recommended before attempting this procedure.

Uploaded by

dongvac
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

How to use the ETL MC68HC908AZ60 FLASH /EERPOM PROGRAMMER (Practice test)

Explore Jaeger cluster T1/21KE8-JA (see Figure 1) Magneti Marelli produced (p.n. 550411090006)
MCU MC68HC05H12(0H57A) inside

Figure 1

Connect the dashboard to MC68HC908AZ60 programmer. Check hardware connection before attach serial port cable and power
connection wires (see Figures 7, 8, 9, 10) NOTE: Lift (cut) PTB3 (PIN 46) from explorer board (see Figure 10)
Attach LPT port cable and turn ON labor power supply source (see user manual e08prog.pdf components layout)*
Start HC08 programmer version 2.1
Follow next steps (see Figures 2,3,4,5):

1 > Click DEVICE button


2 > Select MC68HC05H12(0H57A) device
3 > Select ICP programming interface
4 > Select MON08 pin configuration mode
5 > Click READ button

6 > Click START button and waiting when operation complete


7 > Click EDITOR button to start dump editor
Now you can open editor result on dashboard display and see result (see Figure 6)

7 > step
1 > step

2 > step
Figure 2

3 > step

Figure 3

4 > step

Figure 4

5 > step
6 > step
Figure 5

EEPROM data memory

Figure 6

MON08 adapter

GND (blue)

Programmer board

+12..13Volt >=500 mA (red)

Figure 7

Figure 8

CNT2

CNT1

Figure 9

IRQ (CNT1)
GND (CNT1)
RESET (CNT2)

GND (CNT2)

PTC0 (CNT2)
CND (CNT1)
HIGH1 (CNT2)

VCC (CNT1)

PTA0 (CNT1)

Figure 10
Pin 46 PTB3 lift (cut) from explored board before start ICP procedure

Figure 11

NOTE: MC68HC05HC12 device contains 256 bytes of EEPROM. Programming the EEPROM is performed by the user on a single-byte basis
by manipulating the EEPROM control register, located at address $001C
*Attention! Read e08prog.pdf users manual before start this work

WARNING: MOTOROLA firmware loaders may be difference for mask sets with the same names, according with customer requirement!!!
You can use MC68HC908AZ60 FLASH/EEPROM programmer for YOUR OWN RISK ONLY!
e-mail: alex_etl@yahoo.com
: alexetl@yahoo.com

You might also like