Pulldown Explained. http://www.zerocut.com/tech/pulldown.

html

2-3 Pulldown Explained

Thanks to Ron Friedman

2-3 Pulldown

An NTSC video image consists of 525 horizontal lines of information. The electron
gun scans top to bottom, left to right, odd numbered lines first, then the even
numbered lines. Each full scan of even numbered lines, or odd numbered lines
constitutes a "field". Each field scan takes 1/60th of a second, therefore a whole frame
is scanned each 1/30th of a second. (literally 29.97 frames per second)

Film is generally shot and projected at 24 frames per second (fps), so when film
frames are converted to NTSC video, the rate must be modified to play at 29.97 fps.
During the telecine process, twelve (12) fields are added to each 24 frames of film (12
fields = 6 frames) so the same images that made up 24 frames of film then comprise
30 frames of video.Video plays at a speed of 29.97 fps so the film actually runs at
23.976 fps when transferred to video.

The Avid Film Composer assumes a 2-3 pull down. That means that the first frame of
film is represented by 2 fields of video; the second frame of film is represented by 3
fields of video (1.5 frames); the third frame of film is again represented by two ields
and the fourth frame of film is represented by 3 fields, and so on. In the end, what was
running at 23.976 fps is running at 29.97 fps.

The first frame of video contains two fields of the 1st (A) frame of film.

The second frame of video contains two fields of the 2nd (B) frame of film.

The third frame of video contains one field of the 2nd (B) and 3rd (C) frames of film.

The fourth frame of video contains one field of the 3rd (C) and 4th (D) frames of film.

The fifth frame of video contains two fields of the 4th (D) frame of film.

1 of 5 3/13/15, 8:54 AM
Pulldown Explained. http://www.zerocut.com/tech/pulldown.html

The graphics above shows how four frames of film become five frames of video;
repeat that process six times and 24 frames of film become 30 frames of video.
(technically, 23.976 frames of film become 29.97 frames of video, but it is easier to

2 of 5 3/13/15, 8:54 AM
Pulldown Explained. http://www.zerocut.com/tech/pulldown.html

speak in whole numbers)

The Avid digitizes (records) and plays the film at 24 fps, in a Film Project, so the
video has to be stripped of the fields that were added in the tape transfer process.
Systems that digitize the 29.97 frames of video produce film Cut Lists by a process
called matchback where the timecode (from an EDL) is used to locate the nearest
real film frame for the negative cutter. Matchback is only accurate + or - one frame.
One can choose to work at 30fps on an Avid and matchback for a negative cut, or
work at 24 fps and produce a frame accurate negative Cut List. There is a process by
which one can import an EDL from a 24 fps film project into a 30 fps project and
redigitize the picture at a higher resolution (film projects only capture in single field
resolutions).

Pulldown Phase

Avid software always assumes the first frame of a logged clip is an "A" frame unless
it is told otherwise. This setting allows the user to work more easily with tapes that do
not follow the standard conventions. For example, some telecien sessions or HD
down-converts may have "B" frames on 00s and 05s, rather than 01s and 06s which is
standard practice. Here one can inform the software that some other frame is on the
00s and 05s, so logging and capture-on-the-fly can be done accurately in a 24p
project. If clips are imported from a shot log, this setting will not override the shot
log's setting for the pull-in frame. Clips already logged in correctly can be modified
using the Modify feature in the Clip menu.

2-3 Pulldown vs. 3-2

3 of 5 3/13/15, 8:54 AM
Pulldown Explained. http://www.zerocut.com/tech/pulldown.html

than "A".

During the telecine process a computer file should be created which indicates the
relative timecode, keykode and pullin frames ("A" frames) for each clip to be
digitized. Once this file is imported into the Film Composer, clips can be batch
digitized without a great deal of data entry on the operators part. You should have the
KeyKode numbers displayed on the screen (burned in during the film-to-tape transfer)
with an indication of the pulldown frames at the right end of those numbers and a hole
punched on an "A" frame at the head of the roll where the digitizing will begin. If
your KeyLog files are not accurate, or are missing, you can define and/or log the clips
to be digitized individually. If the pulldown frames are not indicated on screen, you
must determine which frame is an "A" frame by another method.

How to identify a pulldown frame

Identify a single frame of film (hole punch, a single frame in leader, a speck of
dust,...) and scroll field by field through the video watching the time code. (each scroll
bar that rolls across the screen indicates a new field, not a new frame)

If the selected frame is represented by only two fields, it is either an "A" or "C" frame.
"A" - if the timecode changes after the 2nd field it is an "A" frame.
"C" - if the timecode changes after the first field, it is a "C" frame.

If there are three fields representing the selected frame, it is either a "B" or "D" frame.
"B" - if the timecode changes after the 2nd field it is a "B" frame.
"D" - if the timecode changes after the 1st field it is a "D" frame.

Another slightly confusing consideration: When the pulldown process occurs, it turns
out that the video version of the film runs slightly SLOWER than the original film did.
This occurs because the film is running at 24 frames per second, but in order to create
the right pattern of A-B-C-D on the video tape, which runs at 29.97 frames per
second, the film was actually played at 23.976 fps during the telecine (film->tape
process). This leads us to dealing with audio considerations...

Combined Fields

With the NuVista and Enhancement Boards one can select an "e" resolution (i.e.,
AVR6e) in a single field capture. The "e" board combines the two fields which
represent an individual frame of film into one field of captured image. The sequence
in a Film Project is A-B-C-D, but with the "e" resolution the image appears more
attractive to the eye AND slightly reduces the storage requirements. he "e" board
works only with a 640x480 image and is not compatible with the 720x486 Avid
Broadcast Video Board (ABVB).

Avid software versions 6.0.x through 6.1.x use the ABVB and did not offer the option
to combine fields. Software versions 6.5.x and later have a software feature which
combines fields, much as the Enhancement Board does with the NuVista images. A
check-box in the Digitize Settings turns on the Combine Fields option. Combine
Fields only works in Film Projects. Single field resolutions in a film project can

4 of 5 3/13/15, 8:54 AM
Pulldown Explained. http://www.zerocut.com/tech/pulldown.html

include either "s" or "m" resolutions (i.e., AVR6s and AVR6m).

There is no need for the "combine fields" option in the Avid Meridien 24p project
because the entire frame is captured in a progressive mode so 100% of the image is
used and there are no fields as such. See Avid 24p - The Basics for more details.

Due to the fact that the "C" frame of film is split between two different frames of
video, the frame/field count in the timecode burn-in will be blurred, as it contains two
different TC addresses for the "C" frame when using Combine Fields.

Back to the Technical Documents page.

Link to Avid Technology, Inc. for more technical info regarding Avid products.
Link to Filmmaker's Home Page/ Editing.
Link to Zerocut main page.
e-mail Alan Stewart.

5 of 5 3/13/15, 8:54 AM