1 2 3 4

A D- A P T R O N IC
engine management -
M2000 J1-26 Pin Connector Wiring Diagram

From 12V ignition

switched supply,

(see other page)

pin 7 on J1
D D

Ignition Cylinder 1

Ignition Cylinder 3

Ignition Cylinder 4
Ignition Cylinder 2
Injector Cylinder 1

Injector Cylinder 6

Injector Cylinder 2

Injector Cylinder 3

Injector Cylinder 4

Injector Cylinder 5
Spare Pins Note:

For more information about spare pins, connect the

12V
ECU to the PC software "Eugene" and from the
home table select "Wiring and Installation".

Injector Output Note:

1. Injector outputs can also be driven-low auxiliary
outputs, PWM capable, max current of 4A.
2. Injector outputs are wired in cylinder order.
(eg 1-1, 2-2 etc)

Injector Supply Note:

[G/W]
[L/W]

[P/W]
[G/O]

[G/Y]
[G/R]
The same 12V that supply Pin 7 of J1-34 pin

[L/O]

[L/Y]

[L/G]
[L/R]

[P/G]

[P/B]
connector on the other sheet.

[L]
C C

1 2 3 4 5 6 7

8 9 10 11 12 13
Inj 1 Inj 2 Inj 3 Inj 4 Inj 5 Pin 6 Spare Pin 7 Spare

Inj 6 Ign 1 Ign 2 Ign 3 Ign 4 Pin 13 Spare

J2 - 26 PIN CONNECTOR

Inj 7 Ign 5 Ign 6 Ign 7 Ign 8 Pin 19 Spare

Inj 8 Aux 1 Aux 2 Aux 3 Aux 4 Pin 25 Spare Pin 26 Spare

14 15 16 17 18 19

20 21 22 23 24 25 26
B B
[Gy/B]

[Gy/G]
[Gy/R]

[Gy/L]

[G/B]
[G/V]
[G/L]
[L/B]

[P/Y]
[L/P]

[P/L]
Ignition Output Note:
[G]

[P]
1. Ignition outputs can also be driven-low auxiliary
outputs, max current of 0.5A.
2. All ignition outputs must use external ignitor
or coils with built-in ignitor.
3. Ignition outputs are wired in cylinder
Auxiliary Output 2

Auxiliary Output 3

Auxiliary Output 4
Auxiliary Output 1

Ignition Cylinder 5

Ignition Cylinder 6

Ignition Cylinder 7

Ignition Cylinder 8
order. (eg 1-1, 2-2 etc)
Injector Cylinder 8

Injector Cylinder 7

Title
A Additional Note: Wire Colors Note: A
B - Black Br - Brown G - Green Gy - Grey M2000 J1-26 Pin Connector Wiring Diagram
For staged injection and split spark modes, see L - Blue O - Orange P - Pink R - Red
V - Violet Y - Yellow W - White Size Number Revision
application specific wiring diagrams or connect the
If wire has two colors and is shown with a slash,
ECU to the PC software "Eugene", and from the home eg [B/R], it means black with a red trace. A4
1
12V

tab select "Wiring and Installation".

Date: 10-Aug-2017 Sheet of
File: Drawn By: Jean Krizel Florentino
Z:\Products\Modular\looms\M2000_long_revised_2017_01_22.DDB
1 2 3 4
 1 2 3 4

A D- A P T R O N IC M2000 J2-34 Pin Connector Wiring Diagram

engine management -
D Note: 12V power for digital sensors. D

or Fuel Flex Sensor

Cam Angle Sensor 2
Crank Angle Sensor

Cam Angle Sensor 1

GND

GND
GND
12V

12V

12V
SIG

SIG
SIG

Coolant Temp. Sensor

Note: J2-17 does not

Fuel Pressure Sensor

Oil Pressure Sensor

need to be wired EFI Relay Wiring
[W]

[W]

[W]

Air Temp Sensor

[Y]
[B]

[R]
2 Core [B]

2 Core [B]

2 Core [B]

[Y/Br]

[R/W]
[Y/G]
[B/G]

[Y/B]

[V/R]
[Y/O]

[Y/V]
Ignition Switch

[Gy]
[Br]

[R]

[B]

[B]
[Y]

20A 20A 20A

C C

1 2 3 4 5 6 7 8 9 EFI Relay
CAR BATTERY 85 30
10 11 12 13 14 15 16 17
CAS 1 CAS 2 IMAP Fuel P ECT Servo 12V PGND PGND 12V
86 87 Powers
SGND CAS 3 EMAP Oil P MAT CAN H EFI/Fuel Pump Relay Ign Sw the

J2-34 PIN CONNECTOR

injectors
and
Note: Ground at ignition
engine 85 30 coils.
O2 1 O2 2 TPS 1 Fuel T Ext 0-5V 1 CAN L VSS Tacho
Fuel Pump Relay
Knock +5V TPS 2 Oil T Ext 0-5V 2 Dig in 1 Dig in 2 Dig in 3 Dig in 4 86 87
18 19 20 21 22 23 24 25

26 27 28 29 30 31 32 33 34
Fuel Pump
B B
Throttle Position Sensor
1 Core [Gy]

1 Core [B]

1 Core [B]

Note: Ground

[Gy/W]
at engine
[Br/G]

[Br/Y]

[Br/O]

[V/Br]
[W/G]

[W/O]

[W/Y]
[Br/R]

[W/R]
Oxygen Sensor 1

[Y/R]

[V/B]
[Y/L]

Oil Temperature
[R/L]
Knock Sensor

Note: CAN internal 120 Ohm termination can be

CAN Wiring enabled or disabled in software.

Tachometer
Power supply for digital sensor
[W]

[W]

[B]

CAN H
To Pin 15

To Pin 23
CAN L
Dig in 1

Dig in 2

Dig in 3

Dig in 4
7
8
9
3 4 5 6

0
2
1

Note: Ground at engine

Vehicle Speed Sensor

Title
12V
SIG
GND

A Wire Colors Note: Note: A

B - Black Br - Brown G - Green Gy - Grey 1. Pins with red text are optional. M2000 J2-34 Pin Connector Wiring Diagram
Vehicle Speed Sensor

L - Blue O - Orange P - Pink R - Red 2. Shielded wires are already connected to the sensor ground
(SGND). Size Number Revision
V - Violet Y - Yellow W - White
Sample

If wire has two colors and is shown with a slash,

A4
1
eg [B/R], it means black with a red trace.
Date: 28-Jul-2017 Sheet of
File: Drawn By: Jean Krizel Florentino
\\MARGE\Technical\Products\Modular\looms\M2000_long_revised_2017_01_22.DDB
1 2 3 4