8 Electrical equipment

80A BATTERY

80B HEADLIGHTS

80C XENON BULBS

81A REAR LIGHTING

cardiagn.com
81B INTERIOR LIGHTING

81C FUSES

82A ENGINE IMMOBILISER

82B HORN

82C ALARM

83A INSTRUMENT PANEL

83C ON-BOARD TELEMATICS SYSTEM

X45

NOVEMBER 2009 EDITION ANGLAISE

"The repair procedures given by the manufacturer in this document are based on the All rights reserved by Renault.
technical specifications current when it was prepared. Copying or translating, in part or in full, of this document or use of the service part reference
The procedures may be modified as a result of changes introduced by the manufacturer in numbering system is forbidden without the prior written authority of Renault.
the production of the various component units and accessories from which the vehicles are
constructed".

© Renault s.a.s 2007

 83D CRUISE CONTROL

84A CONTROL - SIGNALS

85A WIPING - WASHING

86A RADIO

87B
PASSENGER COMPARTMENT CONNECTION
UNIT

87C OPENING ELEMENT MANAGEMENT

cardiagn.com
87D ELECTRIC WINDOWS - SUNROOF

87F PARKING DISTANCE CONTROL

87G ENGINE COMPARTMENT CONNECTION UNIT

88A WIRING HARNESS

88C AIR BAG AND PRETENSIONERS

88D DRIVER'S POSITION

X45

NOVEMBER 2009 EDITION ANGLAISE

"The repair procedures given by the manufacturer in this document are based on the All rights reserved by Renault.
technical specifications current when it was prepared. Copying or translating, in part or in full, of this document or use of the service part reference
The procedures may be modified as a result of changes introduced by the manufacturer in numbering system is forbidden without the prior written authority of Renault.
the production of the various component units and accessories from which the vehicles are
constructed".

© Renault s.a.s 2007

KOLEOS - Section 8 ContentsPages

KOLEOS - Section 8

Contents

Pages

80A BATTERY 80C XENON BULBS

Battery: Precautions for the Xenon headlight high voltage

repair 80A-1 unit: Removal - Refitting 80C-1

cardiagn.com
Battery: Removal - Refitting 80A-3 Headlight beam adjustment
rear sensor: Removal -
Battery tray: Removal - Refitting 80C-3
Refitting 80A-5

81A REAR LIGHTING

80B HEADLIGHTS
Rear lighting: List and
Headlight: Removal - location of components 81A-1
Refitting 80B-1
Rear wing light: Removal -
Headlight: Adjustment 80B-3 Refitting 81A-3
Front lighting: List and Rear opening element light:
location of components 80B-7 Removal - Refitting 81A-5
Headlight bulb: Removal - Rear light bulb: Removal -
Refitting 80B-12 Refitting 81A-6
Front fog light: Removal - 3rd brake light: Removal -
Refitting 80B-19 Refitting 81A-8
Side indicator: Removal - Rear fog lights: Removal -
Refitting 80B-21 Refitting 81A-9
Additional cornering lights Number plate light: Removal
computer: Removal - - Refitting 81A-10
Refitting 80B-22
 Contents

81B INTERIOR LIGHTING 82B HORN

Interior lighting: List and Audible warning: Removal -

location of components 81B-1 Refitting 82B-1

Interior light: Removal -

Refitting 81B-4

Headlining light: Removal - 82C ALARM

Refitting 81B-5
Alarm: List and location of
Lower door light: Removal -
components 82C-1
Refitting 81B-6
Bonnet switch: Removal -
Courtesy light: Removal -
Refitting 82C-2
Refitting 81B-7
Anti-intrusion alarm sensor:
Storage compartment light:
Removal - Refitting 82C-3
Removal - Refitting 81B-8

cardiagn.com
Centre console light:
Removal - Refitting 81B-9
83A INSTRUMENT PANEL
Luggage compartment light:
Removal - Refitting 81B-10
Instrument panel: Removal -
Refitting 83A-1

Vehicle position sensor:

81C FUSES Removal - Refitting 83A-3

Fuses: List and location of

components 81C-1
83C ON-BOARD TELEMATICS SYSTEM

Navigation: List and location

82A ENGINE IMMOBILISER of components 83C-1

Radio navigation: Removal -

Immobiliser system: List and
Refitting 83C-2
location of components 82A-1
Navigation computer:
Start button: Removal -
Removal - Refitting 83C-3
Refitting 82A-4
Navigation interface unit:
Electric steering column lock:
Removal - Refitting 83C-4
Removal - Refitting 82A-7
Central control: Removal -
Card reader: Removal -
Refitting 83C-5
Refitting 82A-10
Navigation screen: Removal
Starting aerial: Removal -
- Refitting 83C-6
Refitting 82A-13
Navigation aerial: Removal -
Battery for remote door
Refitting 83C-8
locking control: Removal -
Refitting 82A-17
 Contents

83D CRUISE CONTROL 85A WIPING - WASHING

Cruise control - speed Wiping and washing: List and

limiter: List and location of location of components 85A-1
components 83D-1
Windscreen wiper blade:
Switch: Removal - Refitting 83D-2 Removal - Refitting 85A-6

Steering wheel switch: Windscreen wiper arm:

Removal - Refitting 83D-4 Removal - Refitting 85A-7

Windscreen wiper
mechanism: Removal -
Refitting 85A-9
84A CONTROL - SIGNALS
Windscreen wiper motor:
Steering column switch Removal - Refitting 85A-11
assembly: List and location
Rear screen wiper blade:
of components 84A-1
Removal - Refitting 85A-12

cardiagn.com
Rotary switch: Removal -
Rear screen wiper arm:
Refitting 84A-2
Removal - Refitting 85A-13
Steering column switch
Rear screen wiper motor:
assembly: Removal -
Removal - Refitting 85A-15
Refitting 84A-4
Rain and light sensor:
Hazard warning lights and
Removal - Refitting 85A-16
central door control:
Removal - Refitting 84A-5 Screen washer pump:
Removal - Refitting 85A-19
ESP inhibitor switch:
Removal - Refitting 84A-7 Headlight washer pump:
Removal - Refitting 85A-20
Remote headlight beam
adjustment control: Removal Headlight washer jet:
- Refitting 84A-8 Removal - Refitting 85A-21
Lighting dimmer: Removal - Front screen washer jet:
Refitting 84A-9 Removal - Refitting 85A-22
Exterior rear view mirror Rear screen washer jet:
control switch: Removal - Removal - Refitting 85A-23
Refitting 84A-10
Windscreen washer
Heated rear screen: Repair 84A-11 reservoir: Removal - Refitting 85A-24
Heated seat pad switch: Windscreen washer reservoir
Removal - Refitting 84A-13 neck: Removal - Refitting 85A-26
Hill descent control system:
Removal - Refitting 84A-14

Transmission mode 86A RADIO

management control:
Removal - Refitting 84A-16 Radio: List and location of
components 86A-1

Radio: Removal - Refitting 86A-4

 Contents

86A RADIO 87D ELECTRIC WINDOWS - SUNROOF

Receiver: Removal - Refitting 86A-6 Front electric window

switches on driver's door:
Radio aerial: Removal - Removal - Refitting 87D-4
Refitting 86A-8
Front electric window switch
Tweeter: Removal - Refitting 86A-10 on passenger door: Removal
Front speakers: Removal - - Refitting 87D-5
Refitting 86A-11 Rear electric window switch:
Rear speakers: Removal - Removal - Refitting 87D-6
Refitting 86A-13 Sunroof switch: Removal -
CD changer: Removal - Refitting 87D-7
Refitting 86A-14 Sunroof opening motor:
Display: Removal - Refitting 86A-15 Removal - Refitting 87D-8

Radio control satellite:

cardiagn.com
Removal - Refitting 86A-17

Subwoofer: Removal - 87F PARKING DISTANCE CONTROL

Refitting 86A-18
Parking distance control: List
and location of components 87F-1

Parking distance control

PASSENGER COMPARTMENT
87B switch: Removal - Refitting 87F-3
CONNECTION UNIT
UCH: Removal - Refitting 87B-1 Parking distance control
buzzer: Removal - Refitting 87F-4

Proximity radar: Removal -

Refitting 87F-5
87C OPENING ELEMENT MANAGEMENT
Parking distance control
computer: Removal -
Opening elements
Refitting 87F-7
management: List and
location of components 87C-1

Opening aerial: Removal -

Refitting 87C-3 ENGINE COMPARTMENT CONNECTION
87G
UNIT
Tailgate opening switch:
Removal - Refitting 87C-5 Protection and Switching
Unit: Removal - Refitting 87G-1
Tailgate locking switch:
Removal - Refitting 87C-7

88A WIRING HARNESS

87D ELECTRIC WINDOWS - SUNROOF Computers: List and location

of components 88A-1
Electric window: List and
location of components 87D-1 Diagnostic socket: List and
location of components 88A-3
Electric sunroof: List and
location of components 87D-2
 Contents

88C AIR BAG AND PRETENSIONERS 88D DRIVER'S POSITION

Airbag and pretensioners: Cigarette lighter: Removal -

List and location of Refitting 88D-1
components 88C-1

Airbag and pretensioners:

Precautions for the repair 88C-6

Airbags and pretensioners:

Recycling - Destruction 88C-7

Airbag computer: Removal -

Refitting 88C-9

Driver's frontal airbag:

Removal - Refitting 88C-10

Passenger's frontal airbag:

Removal - Refitting 88C-12

cardiagn.com
Front (chest-level) side
airbag: Removal - Refitting 88C-15

Side curtain airbag: Removal

- Refitting 88C-17

Side impact sensor: Removal

- Refitting 88C-20

Inhibitor switch: Removal -

Refitting 88C-22

Front seat lap belt

pretensioner: Removal -
Refitting 88C-23

Front seat belt buckle:

Removal - Refitting 88C-24

Rear seat belt buckle:

Removal - Refitting 88C-26

Front side seat belt: Removal

- Refitting 88C-27

Rear side seat belt: Removal

- Refitting 88C-30

Rear centre seat belt:

Removal - Refitting 88C-32

Passenger airbag
deactivation warning light:
Removal - Refitting 88C-34

Seat belt reminder warning

light: Removal - Refitting 88C-35

Front impact sensor:

Removal - Refitting 88C-36
 BATTERY
Battery: Precautions for the repair 80A
I - SAFETY Safeguarding against the danger of explosion, which
can be caused by handling a battery carelessly, must
be taken very seriously.
IMPORTANT
A battery contains sulphuric acid, a dangerous sub-
stance. IMPORTANT
If acid splashes on to your clothing, rinse all con- To avoid all risk of sparks, ensure that all electrical
taminated areas thoroughly in water. consumers are fully switched off.

If it comes into contact with the skin or eyes, seek When a battery is being charged inside a building,
medical attention. switch off the charger before connecting or discon-
necting the battery.
Do not place any metallic items on the battery as
1 - DANGER: RISK OF ACID WHEN HANDLING AND this may create a short circuit across the terminals.
WHEN MOUNTING IS INCORRECTLY TIGHTENED
Never hold a naked flame, welding gun, blowtorch,
Sulphuric acid is a highly aggressive and toxic sub- cigarette or lighted match near to a battery.
stance which corrodes most metals.
When handling batteries, it is very important to take the
II - CLEANLINESS

cardiagn.com
following precautions:
- protect your eyes by wearing goggles, Check that there is no salt leakage (sulphation) on the
battery terminals.
- wear acid-proof gloves and clothing.
Clean the battery terminals if salt has accumulated
(see 80A, Battery, Battery: Removal - Refitting,
2 - DANGER: RISK OF EXPLOSION LINKED TO page 80A-3) .
CHARGING AND TO INCORRECT TIGHTENING OF
THE TERMINALS
III - GENERAL RECOMMENDATIONS

IMPORTANT
To prevent damaging the battery or even causing it WARNING
to explode, do not place any heat sources or create These vehicles are equipped with a battery with low
any sparks near a charging battery. water consumption. Topping up the electrolyte is
therefore prohibited.

WARNING
Poor contact may cause starting or charging faults, WARNING
create sparks and cause the battery to explode.
Before disconnecting the battery:
When a battery is charging, oxygen and hydrogen are
- wait for the motor-driven fan assembly to stop,
produced. Gas formation is at its maximum when the
battery is completely charged. The quantity of gas pro- - wait for the computer to finish saving (1 minute).
duced is proportional to the intensity of the charging
current.
The oxygen and hydrogen mix in the free space on the WARNING
surface of the plates which forms an explosive mixture.
Some vehicles are only fitted with « TB » (low
This mixture is highly explosive. height) batteries. To avoid damaging the bonnet,
only refit a battery which is identical to the battery
The smallest of sparks or heat sources can cause an
originally fitted.
explosion. The explosion is so strong that the battery
can shatter and spray the acid into the surrounding at-
When refitting the battery or every time it has been dis-
mosphere.
connected, carry out some reprogramming without the
People nearby are at risk (exploded fragments, acid diagnostic tool, so that the vehicle operates correctly
splashes). Acid splashes are dangerous. They also (see 80A, Battery, Battery: Removal - Refitting,
damage clothing. page 80A-3) .

80A-1
 BATTERY
Battery: Precautions for the repair 80A

cardiagn.com

80A-2
 BATTERY
Battery: Removal - Refitting 80A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm

battery mounting nuts 5 N.m 1 - DISCONNECTION

positive battery terminal 6 N.m

nut

negative battery termi- 6 N.m

nal nut

IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see 80A, Battery, Battery: Precautions for
the repair, page 80A-1) .

cardiagn.com
REMOVAL 130833
a Undo the negative battery terminal nut (1) .
I - REMOVAL PREPARATION OPERATION a Disconnect the negative wiring from the negative
battery terminal.
a Switch off the ignition.

2 - REMOVAL
WARNING

Before disconnecting the battery:

- wait for the motor-driven fan assembly to stop,
- wait for the computer to finish saving (1
minute).

WARNING
The visual indicator cannot be considered reli-
able in After-Sales; do not use it to determine the
state of the battery.

130834
a Undo the positive battery terminal nut (2) .
a Disconnect the positive wiring from the positive bat-
tery terminal.

80A-3
 BATTERY
Battery: Removal - Refitting 80A
a Push the positive battery wiring fully onto the posi-
tive battery terminal.

WARNING
Incorrect tightening could cause heating of con-
tacts, starting or charging faults, sparking, or
could cause the battery to explode (see 80A,
Battery, Battery: Precautions for the repair,
page 80A-1) .

a Torque tighten the positive battery terminal nut (6

N.m).

2 - CONNECTION
130835
a Push the negative battery wiring fully onto the nega-
a Loosen the battery mounting nuts (3) . tive battery terminal.

a Remove:

cardiagn.com
WARNING
- the battery mounting (4) , Incorrect tightening could cause heating of con-
tacts, starting or charging faults, sparking, or
- the battery cover (5) ,
could cause the battery to explode (see 80A,
Battery, Battery: Precautions for the repair,
- the battery,
page 80A-1) .
- the battery lower cover.
a Torque tighten the negative battery terminal nut (6
a In the event of a replacement operation, perform the N.m).
necessary checks (see Checking the charge cir-
cuit: Tests) (Technical Note 6014A, 16A, Starting III - FINAL OPERATION
and charging).
a

Note:
REFITTING
When refitting the battery and after every time it
has been disconnected for longer than 3 sec-
I - REFITTING PREPARATION OPERATION onds, it may be necessary to carry out some
operations without the diagnostic tool, so that the
a Check the battery (see Battery: Check) (Technical vehicle operates correctly.
Note 6002A, 80A, Battery).
a If the battery is disconnected for more than 10 sec-
onds, reinitialise the electric windows: raise all the
II - REFITTING OPERATION FOR PART windows to their upper stop and keep the raise but-
CONCERNED ton pressed in this position for at least 3 seconds.
a If the battery is disconnected for more than 5 sec-
1 - REFITTING onds: reinitialise the rain and light sensor: perform
key ON, key OFF.
a Fit the battery lower cover.

a Refit:

- the battery,

- the battery cover,

- the battery mounting.

a Torque tighten the battery mounting nuts (5 N.m).

80A-4
 BATTERY
Battery tray: Removal - Refitting 80A
M9R
- the diesel injection computer from the battery tray
(see Diesel injection computer: Removal - Refit-
Tightening torquesm ting) (13B, Diesel injection).
battery tray bolts 10 N.m
REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
IMPORTANT
Consult the safety and cleanliness advice and oper- a Refit:
ation recommendations before carrying out any - the diesel injection computer on the battery tray
repair (see 80A, Battery, Battery: Precautions for (see Diesel injection computer: Removal - Refit-
the repair, page 80A-1) . ting) (13B, Diesel injection),
- the battery tray - diesel injection computer assem-
bly.
REMOVAL
a Clip:
- the wiring bracket onto the battery tray,

cardiagn.com
I - REMOVAL PREPARATION OPERATION
a Remove the battery (see 80A, Battery, Battery: Re- - the wiring.
moval - Refitting, page 80A-3) . a Connect the diesel injection computer connectors.
a Refit the battery tray bolts.
II - OPERATION FOR REMOVAL OF PART
a Torque tighten the battery tray bolts (10 N.m).
CONCERNED
a Clip on the turbocharging pressure regulator hose.

II - FINAL OPERATION.
a Refit the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

130357

a Unclip the hose (1) from the turbocharging pressure

regulator.
a Remove the bolts (2) from the battery tray.

a Disconnect the connectors (3) from the diesel injec-

tion computer.
a Unclip:

- the wiring,
- the wiring bracket (4) from the battery tray.

a Remove:
- the battery tray - diesel injection computer assem-
bly,

80A-5
 BATTERY
Battery tray: Removal - Refitting 80A
2TR
a Unclip the wiring.

Tightening torquesm a Remove:

battery tray bolts 21 N.m - the battery tray - fuel injection computer - gearbox
computer assembly,

- the fuel injection computer from the battery tray

(see Petrol injection computer: Removal - Refit-
IMPORTANT
ting) (17B, Petrol injection),
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any - the gearbox computer from the battery tray (see
repair (see 80A, Battery, Battery: Precautions for
Automatic gearbox converter: Removal - Refit-
the repair, page 80A-1) .
ting) (23A, Automatic gearbox).

REMOVAL
REFITTING

I - REMOVAL PREPARATION OPERATION

cardiagn.com
I - REFITTING OPERATION FOR PART
a Remove:
CONCERNED
- the air inlet sleeve (see Air filter unit: Removal -
Refitting) (12A, Fuel mixture), a Refit:
- the battery (see 80A, Battery, Battery: Removal - - the gearbox computer on the battery tray, (see Au-
Refitting, page 80A-3) .
tomatic gearbox converter: Removal - Refitting)
(23A, Automatic gearbox).
II - OPERATION FOR REMOVAL OF PART
CONCERNED - the fuel injection computer on the battery tray (see
Petrol injection computer: Removal - Refitting)
(17B, Petrol injection),

- the battery tray - fuel injection computer - gearbox

computer assembly.

a Attach the wiring.

a Connect:

- the gearbox computer connector,

- the petrol injection computer connectors.

a Refit the battery tray bolts.

a Torque tighten the battery tray bolts (21 N.m).

II - FINAL OPERATION.

130358 a Refit:
a Remove the bolts (1) from the battery tray.
- the battery (see 80A, Battery, Battery: Removal -
a Disconnect: Refitting, page 80A-3) ,
- the fuel injection computer connectors (2) ,
- the air inlet sleeve (see Air filter unit: Removal -
- the gearbox computer connector (3) . Refitting) (12A, Fuel mixture).

80A-6
 HEADLIGHTS
Headlight: Removal - Refitting 80B
REMOVAL II - OPERATION FOR REMOVAL OF PART
CONCERNED

I - REMOVAL PREPARATION OPERATION

a Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
a Remove the front bumper (see Front bumper: Re-
moval - Refitting) (55A, Exterior protection).

cardiagn.com
130359
130308
a Remove:
a Remove the trim (1) .
- the headlight upper bolts (2) ,
- the clip (3) .
DISCHARGE LAMPS
a

IMPORTANT

To prevent eye injuries:

- do not look at a discharge bulb when lit (voltage
when lit 20000 V),
- do not light a bulb which has not been fitted into
its headlight.

IMPORTANT
To prevent burns, wait until the « computer -
power unit » assembly has cooled before remov- 130360
ing them. a Remove:
a Disconnect the battery (see 80A, Battery, Battery: - the headlight lower bolt (4) ,
Removal - Refitting, page 80A-3) .
- the headlight lower nut (5) .
a Disconnect the headlight connectors.
a Remove the headlight.

80B-1
 HEADLIGHTS
Headlight: Removal - Refitting 80B
REFITTING

I - REFITTING PREPARATION OPERATION

a

WARNING
To avoid any humidity getting into the headlight,
check there are no cracks on the headlight
before carrying out the repair.
Replace all cracked headlights.

II - REFITTING OPERATION FOR PART

CONCERNED
a Connect the headlight connectors.
a Refit:
- the headlight,

cardiagn.com
- the clip,
- the headlight lower nut,
- the headlight lower bolt,
- the headlight upper bolts.

III - FINAL OPERATION

a Refit the front bumper (see Front bumper: Remov-
al - Refitting) (MR 416, 55A, Exterior protection).

DISCHARGE LAMPS
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

a Adjust the headlight beam (see 80B, Headlights,

Headlight: Adjustment, page 80B-3) .

80B-2
 HEADLIGHTS
Headlight: Adjustment 80B
WITHOUT DISCHARGE LAMPS
III - ADJUSTMENT OPERATION
Equipment required
1 - Vertical adjustment
headlight adjustment and checking tool

ADJUSTMENT

I - PREPARATION OPERATION FOR CHECK

a Position the vehicle on a flat, horizontal work sur-
face, without applying the parking brake.
a Check and inflate the tyres (see Tyre pressure:
Identification) (35A, Wheels and tyres).
a Open the bonnet.
a Check:
- that the luggage compartment is empty,

cardiagn.com
- that the headlights are clean.

Note:
Do not get into the vehicle during the operation.
131350
a Position the headlight beam remote adjustment con-
trol to " 0 ". a Use the headlight adjustment and checking tool
to vertically adjust the headlight by turning the bolt
a Switch on the dipped headlights. (1) .

II - CHECKING OPERATION 2 - Horizontal adjustment

a Place a tool headlight adjustment and checking
tool set to -1.2% in front of the vehicle (see Equip-
ment instructions).
a Check the headlight beam adjustment using the tool
headlight adjustment and checking tool (see
Equipment instructions).

131351

a Use the tool headlight adjustment and checking

tool to horizontally adjust the headlight by turning
the bolt (2) .

80B-3
 HEADLIGHTS
Headlight: Adjustment 80B
WITHOUT DISCHARGE LAMPS
IV - FINAL OPERATION.
a Close the bonnet.

cardiagn.com

80B-4
 HEADLIGHTS
Headlight: Adjustment 80B
DISCHARGE LAMPS
III - ADJUSTMENT OPERATION
Equipment required
1 - Vertical adjustment
headlight adjustment and checking tool

ADJUSTMENT

I - PREPARATION OPERATION FOR CHECK

a Put the vehicle on a flat, horizontal work surface,
without applying the parking brake.
a Check and inflate the tyres (see Tyre pressure:
Identification) (35A, Wheels and tyres).
a Open the bonnet.
a Check:
- that the luggage compartment is empty,

cardiagn.com
- that the headlights are clean.

Note:
Do not get into the vehicle during the operation.
131352
a Switch on the dipped headlights.
a Use the headlight adjustment and checking tool
to vertically adjust the headlight by turning the bolt
II - CHECKING OPERATION (1) .
a Place a tool headlight adjustment and checking
tool set to -1.2% in front of the vehicle (see Equip- 2 - Horizontal adjustment
ment instructions).
a Check the headlight beam adjustment using the tool
headlight adjustment and checking tool (see
Equipment instructions).

131353

a Use the tool headlight adjustment and checking

tool to horizontally adjust the headlight by turning
the bolt (2) .

80B-5
 HEADLIGHTS
Headlight: Adjustment 80B
DISCHARGE LAMPS
IV - FINAL OPERATION.
a Close the bonnet.

cardiagn.com

80B-6
 HEADLIGHTS
Front lighting: List and location of components 80B
WITHOUT DISCHARGE LAMPS
I - LIST OF COMPONENTS 2 - Dipped beam headlight bulb

No. Description

(1) Main beam headlight bulbs

(2) Dipped beam headlight bulb

(3) Side light bulbs

(4) Direction indicator bulb

(5) Front fog light

(6) Side repeater

(7) Vertical adjusting bolt 131360

(8) Horizontal adjusting bolt

cardiagn.com
II - LOCATION OF COMPONENTS

1 - Main beam headlight bulbs

131361

3 - Side light bulbs

131358

131357

131359

80B-7
 HEADLIGHTS
Front lighting: List and location of components 80B
WITHOUT DISCHARGE LAMPS
4 - Direction indicator bulb 7 - Vertical adjusting bolt

131355

5 - Front fog light

cardiagn.com
131350

8 - Horizontal adjusting bolt

130837

6 - Side repeater

131351

131732

80B-8
 HEADLIGHTS
Front lighting: List and location of components 80B
DISCHARGE LAMPS
I - LIST OF COMPONENTS

No. Description

(1) Discharge bulb

(2) Cornering light bulb

(3) Side light bulbs

(4) Direction indicator bulb

(5) High voltage unit

(6) Cornering lights computer

131724
(7) Headlight adjustment rear sensor

(8) Side repeater 2 - Cornering light bulb

cardiagn.com
(9) Vertical adjusting bolt

(10) Horizontal adjusting bolt

II - LOCATION OF COMPONENTS

1 - Discharge bulb

131725

131723

131726

80B-9
 HEADLIGHTS
Front lighting: List and location of components 80B
DISCHARGE LAMPS
3 - Side light bulbs 6 - Cornering lights computer

131727

4 - Direction indicator bulb

cardiagn.com
131730

7 - Headlight adjustment rear sensor

131728

5 - High voltage unit

131731

131729

80B-10
 HEADLIGHTS
Front lighting: List and location of components 80B
DISCHARGE LAMPS
8 - Side repeater 10 - Horizontal adjusting bolt

131732

9 - Vertical adjusting bolt

cardiagn.com
131734

131733

80B-11
 HEADLIGHTS
Headlight bulb: Removal - Refitting 80B
WITHOUT DISCHARGE LAMPS

REMOVAL 2 - Side light bulb

I - REMOVAL PREPARATION OPERATION

a Remove:

- the air inlet sleeve to access the left-hand headlight

bulbs (see Air filter unit: Removal - Refitting)
(12A, Fuel mixture),

- the windscreen washer bottle neck to access the

right-hand headlight bulbs (see 85A, Wiping -
Washing, Windscreen washer reservoir neck:
Removal - Refitting, page 85A-26) (85A, Wiping -
Washing).

131356
II - REMOVAL OF PART CONCERNED a Remove the sealing cover by turning it a quarter of a
turn anticlockwise (3) .

cardiagn.com
1 - Direction indicator bulb

131357

a Remove the bulb (4) from the bulb holder.

131354

a Remove the bulb holder by turning it a quarter of a

3 - Main beam headlight bulbs
turn anticlockwise (1) .

131358
131355
a Remove the sealing cover by turning it a quarter of a
a Remove the bulb (2) from the bulb holder. turn anticlockwise (5) .

80B-12
 HEADLIGHTS
Headlight bulb: Removal - Refitting 80B
WITHOUT DISCHARGE LAMPS

131359 131361
a Disconnect the connector from the main beam head- a Disconnect the connector from the dipped beam
light bulb (6) . headlight bulb (9) .
a Unfasten clip (7) .

cardiagn.com
a Unfasten the clip (10) .
a Remove the main beam headlight bulb. a Remove the dipped beam headlight bulb.

4 - Dipped beam headlight bulb REFITTING

I - REFITTING PART CONCERNED

1 - Direction indicator bulb

a Refit:
- an approved PY21W bulb onto the direction indica-
tor bulb holder,
- the bulb holder on the headlight.
a Turn the bulb holder a quarter of a turn clockwise.

2 - Side light bulb

131356
a Refit:
a Remove the sealing cover by turning it a quarter of a
turn anticlockwise (8) . - an approved W5W bulb onto the side light bulb
holder,
- the bulb holder on the headlight.
a Refit the cover by turning it a quarter of a turn clock-
wise.

3 - Main beam headlight bulbs

a Refit an approved H7 bulb on the headlight.
a Clip the clip onto the headlight.
a Connect the connector to the main beam headlight
bulb.
a Refit the cover by turning it a quarter of a turn clock-
wise.

80B-13
 HEADLIGHTS
Headlight bulb: Removal - Refitting 80B
WITHOUT DISCHARGE LAMPS
4 - Dipped beam headlight bulb
a Refit an approved H7 bulb on the headlight.
a Clip the clip onto the headlight.
a Connect the connector to the dipped beam headlight
bulb.
a Refit the cover by turning it a quarter of a turn clock-
wise.

II - FINAL OPERATION.
a Refit:
- the screen washer bottle filler neck (see 85A, Wip-
ing - Washing, Windscreen washer reservoir
neck: Removal - Refitting, page 85A-26) (12A,
Washing - Wiping),
- the air inlet sleeve (see Air filter unit: Removal -

cardiagn.com
Refitting) (12A, Fuel mixture).

80B-14
 HEADLIGHTS
Headlight bulb: Removal - Refitting 80B
DISCHARGE LAMPS

REMOVAL II - REMOVAL OF PART CONCERNED

I - REMOVAL PREPARATION OPERATION 1 - Direction indicator bulb

1 - Direction indicator light, side light and

cornering light bulbs
a Remove:
- the air inlet sleeve to access the left-hand headlight
bulbs (see Air filter unit: Removal - Refitting)
(12A, Fuel mixture),
- the windscreen washer bottle neck to access the
right-hand headlight bulbs (see 85A, Wiping -
Washing, Windscreen washer reservoir neck:
Removal - Refitting, page 85A-26) .

2 - Discharge bulb

cardiagn.com
131555
a a Remove the bulb holder (1) by turning it a quarter of
a turn anticlockwise.
IMPORTANT
To prevent burns, wait until the « computers -
power unit » assemblies are cold before removal.

IMPORTANT

To prevent eye injuries:

- do not look at a discharge bulb when lit (voltage
when lit 20000 V),
- do not light a bulb which has not been fitted into
its headlight.

a Position the vehicle on a two-post lift (see Vehicle:

Towing and lifting) (02A, Lifting equipment).
131556
a Disconnect the battery (see 80A, Battery, Battery: a Remove the bulb (2) from the bulb holder.
Removal - Refitting, page 80A-3) .
a Remove:
- the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
- the headlight (see 80B, Headlights, Headlight:
Removal - Refitting, page 80B-1) .

80B-15
 HEADLIGHTS
Headlight bulb: Removal - Refitting 80B
DISCHARGE LAMPS
2 - Side light bulbs

131560
131557 a Disconnect the cornering light bulb (6) .
a Remove the sealing cover (3) by turning it a quarter a Unfasten clip (7) .
of a turn anticlockwise.

cardiagn.com
a Remove the cornering light bulb.

4 - Discharge bulb

131558

a Remove the bulb (4) from the bulb holder.

131561
3 - Cornering light bulb
a Remove the sealing cover (8) by turning it a quarter
of a turn anticlockwise.

131559
a Remove the sealing cover (5) by turning it a quarter
of a turn anticlockwise.

80B-16
 HEADLIGHTS
Headlight bulb: Removal - Refitting 80B
DISCHARGE LAMPS
2 - Cornering light bulb
a Refit an approved H7 bulb on the headlight.
a Clip the clip onto the headlight.
a Connect the cornering light bulb connector.

a Refit the cover by turning it a quarter of a turn clock-

wise.

3 - Xenon bulb

131562

a Remove the capacitor (9) by turning it anticlockwise.

cardiagn.com
131564

WARNING
The bulb must be handled with care.
The external conductor (11) is very fragile and
131563 must not be damaged.
a Unfasten clip (10) .
a Refit an approved D2S bulb on the headlight.

WARNING a Clip the clip onto the headlight.

To prevent any breakages, handle the bulb by its a Refit:
base. If you should touch the glass, clean it with
- the capacitor by turning it clockwise,
alcohol and a lint-free cloth.
- the cover by turning it a quarter of a turn clockwise.
a Remove the bulb with caution, taking it by the neck.

II - FINAL OPERATION.
REFITTING
1 - Direction indicator light, side light and
I - REFITTING PART CONCERNED cornering light bulbs
a Refit:
1 - Direction indicator bulb
- the windscreen washer bottle neck to access the
a Refit: right-hand headlight bulbs (see 85A, Wiping -
Washing, Windscreen washer reservoir neck:
- an approved PY21W bulb in the direction indicator
Removal - Refitting, page 85A-26) .
bulb holder,
- the air inlet sleeve to access the left-hand headlight
- the bulb holder on the headlight.
bulbs (see Air filter unit: Removal - Refitting)
a Turn the bulb holder a quarter of a turn clockwise. (12A, Fuel mixture),

80B-17
 HEADLIGHTS
Headlight bulb: Removal - Refitting 80B
DISCHARGE LAMPS
2 - Xenon bulb
a Refit:
- the headlight (see 80B, Headlights, Headlight:
Removal - Refitting, page 80B-1) .
- the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .
a Adjust the headlights (see 80B, Headlights, Head-
light: Adjustment, page 80B-3)

cardiagn.com

80B-18
 HEADLIGHTS
Front fog light: Removal - Refitting 80B
ADDITIONAL HEADLIGHTS

REMOVAL 2 - Front fog light

I - REMOVAL PREPARATION OPERATION

a Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
a Remove:
- the front wheel (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
- the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion).

II - OPERATION FOR REMOVAL OF PART

CONCERNED 130837
a Disconnect the front fog light connector (3) .
1 - Front fog light bulb

cardiagn.com
a Remove:
- the bolts (4) from the front fog light,
- the front fog light.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

1 - Front fog light bulb

a Refit:

130836 - an approved P12V bulb onto the bulb holder of the

front fog light,
a Disconnect the front fog light connector (1) .
a Remove: - the bulb holder on the front fog light.

- the bulb holder (2) by turning it a quarter of a turn a Turn the bulb holder a quarter of a turn clockwise.
anticlockwise, a Connect the front fog light connector.
- the bulb from the bulb holder.
2 - Front fog light

a Refit:
- the front fog light,
- the front fog light bolts.
a Connect the front fog light connector.

II - FINAL OPERATION.
a Refit:
- the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),

80B-19
 HEADLIGHTS
Front fog light: Removal - Refitting 80B
ADDITIONAL HEADLIGHTS
- the front wheel (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).

130838
a Adjust the front fog lights using a screwdriver.

cardiagn.com

80B-20
 HEADLIGHTS
Side indicator: Removal - Refitting 80B
REMOVAL REFITTING

OPERATION FOR REMOVAL OF PART REFITTING OPERATION FOR PART CONCERNED

CONCERNED a Replace the bulb only with an approved W5W bulb.
a Refit:
- the side indicator bulb on the bulb holder,
- the side indicator cover on the bulb holder by turn-
ing it a quarter turn clockwise,
- the side indicator on the front wing.

cardiagn.com
130361

a Push the side indicator towards the front of the vehi-

cle (1) .
a Pull the side indicator in the direction of (2) .

130362
a Remove:
- the side indicator cover (3) from the bulb holder (4)
by turning it a quarter turn anticlockwise,
- the side indicator bulb from the bulb holder.

Note:
Support the side indicator wiring using adhesive
tape, so that the side indicator does not fall into
the front wing.

80B-21
 HEADLIGHTS
Additional cornering lights computer: Removal - Refitting 80B
DISCHARGE LAMPS

REMOVAL II - FINAL OPERATION.

a Refit the dashboard lower cover on the driver's side
(see Dashboard: Removal - Refitting) (57A, Interi-
I - REMOVAL PREPARATION OPERATION
or equipment).
a Remove the dashboard lower cover on the driver's
side (see Dashboard: Removal - Refitting) (57A,
Interior equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130363

a Disconnect the additional cornering lights computer

connector (1) .

a Remove:

- the additional cornering lights computer bolt (2) ,

- the additional cornering lights computer (3) .

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

a Refit:

- the additional cornering lights computer,

- the additional cornering lights computer bolt.

a Connect the connector to the additional cornering

lights computer.

80B-22
 XENON BULBS
Xenon headlight high voltage unit: Removal - Refitting 80C
DISCHARGE LAMPS

IMPORTANT

To prevent eye injuries:

- do not look at a discharge bulb when lit (voltage
when lit 20000 V),
- do not light a bulb which has not been fitted into its
headlight.

IMPORTANT
To prevent burns, wait until the « computers - power
unit » assemblies are cold before removal.

cardiagn.com
REMOVAL

130365
I - REMOVAL PREPARATION OPERATION
a Remove the bolt (2) from the high voltage unit.
a Position the vehicle on a two-post lift (see Vehicle: a Disconnect the high voltage unit connector (3) .
Towing and lifting) (02A, Lifting equipment).
a Remove the high voltage unit.
a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-3) .
REFITTING
a Remove:
I - REFITTING PREPARATION OPERATION
- the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection), a Always replace the high voltage unit seal.

- the headlight (see 80B, Headlights, Headlight:

Removal - Refitting, page 80B-1) . II - REFITTING OPERATION FOR PART
CONCERNED
a Connect the high voltage unit connector.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Note:
Check that the connector is locked correctly.

a Refit:
- the bolt of the high voltage unit wiring,
- the high voltage unit with a new seal,
- the high voltage unit bolts.

III - FINAL OPERATION.

a Refit:
- the headlight (see 80B, Headlights, Headlight:
Removal - Refitting, page 80B-1) ,
130364
- the front bumper (see Front bumper: Removal -
a Remove the bolts (1) from the high voltage unit. Refitting) (55A, Exterior protection).

80C-1
 XENON BULBS
Xenon headlight high voltage unit: Removal - Refitting 80C
DISCHARGE LAMPS
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .
a Adjust the headlight beam (see 80B, Headlights,
Headlight: Adjustment, page 80B-3) .

cardiagn.com

80C-2
 XENON BULBS
Headlight beam adjustment rear sensor: Removal - Refitting 80C
DISCHARGE LAMPS
II - REFITTING OPERATION FOR PART
CONCERNED
Tightening torquesm
a Connect the headlight beam adjustment rear sensor
headlight beam adjust- 25 N.m connector.
ment rear sensor bolt
a Fit the sensor with its mounting to the vehicle.
a Refit:
REMOVAL - the headlight beam adjustment rear sensor,
- the bolts for the headlight beam adjustment rear
sensor.
I - REMOVAL PREPARATION OPERATION
a Torque tighten the headlight beam adjustment
a Position the vehicle on a two-post lift (see Vehicle: rear sensor bolt (25 N.m).
Towing and lifting) (02A, Lifting equipment).
III - FINAL OPERATION.
II - OPERATION FOR REMOVAL OF PART a Adjust:
CONCERNED - the front headlights (see 80B, Headlights, Head-

cardiagn.com
light: Adjustment, page 80B-3) ,
- the headlight beam adjustment rear sensor (see
Fault Finding - Programming)(80B, Headlights).

130366

a Remove the bolts (1) from the headlight beam ad-

justment rear sensor.

a Disconnect the connector (2) from the headlight

beam adjustment rear sensor.

a Remove the headlight beam adjustment rear sen-

sor.

REFITTING

I - REFITTING PREPARATION OPERATION

Note:
Replace the sensor if the linkage is damaged
along its length or if there is damage to the ball
joint - lever - linkage connection.

80C-3
 REAR LIGHTING
Rear lighting: List and location of components 81A
I - LIST OF COMPONENTS 2 - Tailgate light

No. Description

(1) Rear light on wing

(2) Tailgate light

(3) Rear light bulbs

(4) High level brake light

(5) Number plate light

II - LOCATION OF COMPONENTS

1 - Rear light on wing

cardiagn.com
130615

3 - Rear light bulbs

130614

130616

81A-1
 REAR LIGHTING
Rear lighting: List and location of components 81A
4 - High level brake light

cardiagn.com
130617

5 - Number plate light

130618

Note:
The number plate lights are located on the tailgate
strip.

81A-2
 REAR LIGHTING
Rear wing light: Removal - Refitting 81A
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130621
a

Note:

130619 Protect the bodywork varnish using a cloth if

a Remove the blanking cover (1) . using a flat-blade screwdriver.

a Remove:
- the rear light using a flat-blade screwdriver,
- the bulb and bulb mounting assembly (4) of the
rear light housing by rotating it anti-clockwise.

Note:
After removing the rear light, check that the
grommets (9) are correctly fitted on the body (it is
possible for water to flow through the grommet).

130620
a Remove the rear light bolt (2) .
a Unclip the retaining clip (3) .

81A-3
 REAR LIGHTING
Rear wing light: Removal - Refitting 81A

cardiagn.com
135216 130623
a Remove: a Refit the rear light on the wing using the centring de-
vices (9) .
- the side light bulb (5) ,
a Clip on the retaining clip.
- the direction indicator bulb (6) ,
a Refit:
- the brake light bulb (7) .
- the rear light bolt,

REFITTING - the blanking cover.

REFITTING OPERATION FOR PART CONCERNED

a When replacing the bulb, use an approved bulb:
- W5W for the side light,
- KHA 12V 21W for the direction indicator,
- P21W for the brake light.
a Refit:
- the bulbs on the mountings,
- the bulb and mounting assembly on the rear light
housing by rotating it clockwise.

81A-4
 REAR LIGHTING
Rear opening element light: Removal - Refitting 81A
REMOVAL - the side light bulb (3) .

OPERATION FOR REMOVAL OF PART REFITTING

CONCERNED
REFITTING OPERATION FOR PART CONCERNED
a Use an approved bulb for replacement:
- P12V / W5W for the side light,
- P12V / W16W for the reversing light.
a Refit the bulbs.
a Connect the connectors.

cardiagn.com
130632

Note:
Protect the bodywork varnish using a cloth if
using a flat-blade screwdriver.

a Remove:
- the tailgate light nuts (1) ,

- the tailgate light using a flat-blade screwdriver.

a Disconnect the connectors.

130634
a Refit:
- the tailgate light on the tailgate using the centring
device (4) ,
- the tailgate light nuts.

130633

a Remove:
- the reversing light bulb (2) ,

81A-5
 REAR LIGHTING
Rear light bulb: Removal - Refitting 81A
REMOVAL - REFITTING 2 - Tailgate light

I - REMOVAL PREPARATION OPERATION

1 - Rear light on wing

a Remove the bulb holder (see 81A, Rear lighting,
Rear wing light: Removal - Refitting, page 81A-3)
.

2 - Tailgate light
a Remove the bulb holder (see 81A, Rear lighting,
Rear opening element light: Removal - Refitting,
page 81A-5) .

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
1 - Rear light on wing
130625
a Remove:
- the side light bulb (4) ,
- the reversing light bulb (5) .

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

1 - Rear light on wing

a Refit:
- the approved P21W bulb for the brake light,
- the approved KHA 12V 21W bulb for the direction
indicator light,
- the approved W5W bulb for the side light.
130624
a Remove:
2 - Tailgate light
- the side light bulb (1) ,
a Refit:
- the direction indicator bulb (2) ,
- the approved P12V/W16W bulb for the reversing
- the brake light bulb (3) . light,
- the approved W5W bulb for the side light.

II - FINAL OPERATION.

1 - Rear light on wing

a Refit the bulb holder (see 81A, Rear lighting, Rear
wing light: Removal - Refitting, page 81A-3) .

81A-6
 REAR LIGHTING
Rear light bulb: Removal - Refitting 81A
2 - Tailgate light
a Refit the bulb holder (see 81A, Rear lighting, Rear
opening element light: Removal - Refitting, page
81A-5) .

cardiagn.com

81A-7
 REAR LIGHTING
3rd brake light: Removal - Refitting 81A
REMOVAL - REFITTING

I - REMOVAL PREPARATION OPERATION

a Remove the tailgate upper trim (see Tailgate trim:

Removal - Refitting) (73A, Non-side opening ele-
ments trim).

130628
a Remove:
- the clips (6) ,

cardiagn.com
- the high level brake light.

REFITTING
130626
I - REFITTING OPERATION FOR PART
a Disconnect the connectors (1) . CONCERNED

a Remove: a When replacing the high level brake light bulb, re-
place the high level brake light assembly.
- the bolt (2) , a Refit the high level brake light.

- the clip (3) . a Connect the connector.

a Move aside the amplifier and its support. II - FINAL OPERATION.

a Fit the amplifier and its support in their original loca-
II - OPERATION FOR REMOVAL OF PART tion.
CONCERNED a Refit:
- the clip,
- the bolt.
a Connect the connectors.
a Refit the tailgate upper trim (see Tailgate trim: Re-
moval - Refitting) (73A, Non-side opening ele-
ments trim).

130627

a Disconnect the connector (4) .

a Unclip clips (5) .

81A-8
 REAR LIGHTING
Rear fog lights: Removal - Refitting 81A
REMOVAL

I - REMOVAL PREPARATION OPERATION

a Position the vehicle on a two-post lift (see Vehicle:

Towing and lifting) (02A, Lifting equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

1 - Rear fog light bulb

a Disconnect the rear fog light connector.

a Remove:

- the bulb holder by rotating it a quarter turn anti-

clockwise,

cardiagn.com
- the bulb from the bulb holder.

2 - Rear fog light

a Disconnect the rear fog light connector.

a Remove:

- the rear fog light bolts,

- the rear fog light from the rear bumper.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

1 - Rear fog light bulb

a Refit:

- an approved W21W bulb in the rear fog light bulb

holder,

- the bulb holder on the rear fog light by rotating it a

quarter turn clockwise.

a Connect the rear fog light connector.

2 - Rear fog light

a Refit:

- the rear fog light on the rear bumper,

- the rear fog light bolts.

a Connect the rear fog light connector.

81A-9
 REAR LIGHTING
Number plate light: Removal - Refitting 81A
REMOVAL - REFITTING

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130631
a Remove the bulb (4) .

REFITTING
130629
a Remove the number plate light bolts (1) .
REFITTING OPERATION FOR PART CONCERNED
a Disconnect the number plate light connectors.
a When replacing the bulb, use an approved W5W
a Remove the number plate lights. bulb.
a Refit the bulb.
a Clip on the plate.
a Connect the number plate light connectors.
a Refit:
- the number plate lights,
- the number plate light bolts.

130630
a Unclip the plate (2) at (3) .

81A-10
 INTERIOR LIGHTING
Interior lighting: List and location of components 81B
2 - Passenger compartment fuse and relay box

I - LIST OF COMPONENTS

No. Description

(1) UCH

(2) Fuse boxes and passenger com-

partment relays

(3) Courtesy light

(4) Headlining light

(5) Courtesy light

(6) Storage compartment light

cardiagn.com
(7) Door sill light

(8) Luggage compartment light 130636

(9) Centre console light 3 - Courtesy light

II - LOCATION OF COMPONENTS

1 - UCH

130635
130637

81B-1
 INTERIOR LIGHTING
Interior lighting: List and location of components 81B
4 - Headlining light 6 - Glove box light

130640

7 - Door sill light

cardiagn.com
130638

5 - Courtesy light

130641

130639

81B-2
 INTERIOR LIGHTING
Interior lighting: List and location of components 81B
8 - Luggage compartment light

cardiagn.com
130642

9 - Centre console light

130643

81B-3
 INTERIOR LIGHTING
Interior light: Removal - Refitting 81B
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

130645

cardiagn.com
130644
a

Note:
If using a flat-blade screwdriver, protect the cour-
tesy light unit with a cloth.

a Unclip the courtesy light (1) using a small flat-blade

screwdriver.
a Disconnect the connector.
130646
a Unclip the transparent cover (2) .
a Remove the bulb.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a When replacing the bulb, use an approved 12V 8W
bulb.
a Connect the courtesy lights connector.
a Refit the courtesy light.

81B-4
 INTERIOR LIGHTING
Headlining light: Removal - Refitting 81B
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130659

a Remove the bolt (3) .

a Unclip the translucent cover at (4) .

130657

130660

a Remove the bulb (5) .

REFITTING

REFITTING OPERATION FOR PART CONCERNED

130658
a Remove the headlining light (1) by unclipping the a When replacing a bulb, use an approved 12V 8W
clips (2) using a small flat-blade screwdriver. bulb.
a Disconnect the connector. a Refit the bulb.
a Clip the translucent cover in place.

a Refit the bolt.

a Connect the connector.
a Refit the headlining light.

81B-5
 INTERIOR LIGHTING
Lower door light: Removal - Refitting 81B
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

Front door side

cardiagn.com
130649
a Remove the translucent cover (3) by unclipping the
clips (4) .

REFITTING
130647
REFITTING OPERATION FOR PART CONCERNED
Rear door side
a When replacing the bulb, use an approved 12V 5W
bulb.
a Refit the translucent cover.
a Connect the connector.
a Refit the lower door light.

130648
a Remove the lower door light (1) or (2) using a small
flat-blade screwdriver.
a Disconnect the connector.

81B-6
 INTERIOR LIGHTING
Courtesy light: Removal - Refitting 81B
SUN VISOR + MIRROR WITH LIGHTING

REMOVAL REFITTING

OPERATION FOR REMOVAL OF PART REFITTING OPERATION FOR PART CONCERNED

CONCERNED
a When replacing the bulb, use an approved 12V 0.25
A bulb.
a Refit:
- the bulb,
- the translucent cover.

cardiagn.com
130650
a Unclip the courtesy light translucent cover (1) using
a small flat-blade screwdriver.

130651
a Remove the bulb (2) .

81B-7
 INTERIOR LIGHTING
Storage compartment light: Removal - Refitting 81B
REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the glovebox (see Glovebox: Removal -

Refitting) (57A, Interior equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130652

a Disconnect the storage compartment light connec-

tor.

a Remove the bulb and mounting assembly (1) by ro-

tating in an anti-clockwise direction.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

a When replacing the storage compartment light bulb,

replace the storage compartment light assembly.

a Refit the storage compartment light (1) by rotating it

clockwise.

a Connect the connector.

II - FINAL OPERATION

a Refit the glovebox (see Glovebox: Removal - Refit-

ting) (57A, Interior equipment).

81B-8
 INTERIOR LIGHTING
Centre console light: Removal - Refitting 81B
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130653
a Remove the centre console light (1) using a small
flat-blade screwdriver.
a Disconnect the connector.
a Remove the bulb.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a Connect the connector.
a Refit the centre console light.

81B-9
 INTERIOR LIGHTING
Luggage compartment light: Removal - Refitting 81B
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

130656
a Remove the bulb (4) .

REFITTING

cardiagn.com
REFITTING OPERATION FOR PART CONCERNED
a When replacing the bulb, use an approved 12V 8W
bulb.
a Refit the bulb.
130654
a Clip the translucent cover in place.
a Unclip the luggage compartment light (1) by com-
pressing the clip using a small flat-blade screwdriv- a Refit the bolt.
er. a Connect the connector.
a Disconnect the connector. a Refit the luggage compartment light.

130655

a Remove the bolt (2) .

a Unclip the translucent cover by unclipping the clips

(3) .

81B-10
 FUSES
Fuses: List and location of components 81C
I - LIST OF COMPONENTS

No. Description

(1) Passenger compartment fuse and relay

box

(2) Engine fuse and relay box / supply fuse

board

(3) Battery protection fuses

(4) Engine compartment connection unit

II - LOCATION OF COMPONENTS

1 - Passenger compartment fuse and relay box

cardiagn.com
130368

2 - Engine fuse and relay box / supply fuse board

130367

130369

81C-1
 FUSES
Fuses: List and location of components 81C
4 - Engine compartment connection unit

cardiagn.com
130370
130372

3 - Battery protection fuses

130373

130371
These fuses are located on the positive battery termi-
nal.

81C-2
 ENGINE IMMOBILISER
Immobiliser system: List and location of components 82A
2 - Front starting aerial

I - LIST OF COMPONENTS

No. Description

(1) UCH

(2) Front starting aerial

(3) Central starting aerial

(4) Rear starting aerial

(5) Start button

(6) Card reader

(7) Electric steering column lock

cardiagn.com
(8) Card
130662

II - LOCATION OF COMPONENTS 3 - Central starting aerial

1 - UCH

130661

130663

82A-1
 ENGINE IMMOBILISER
Immobiliser system: List and location of components 82A
4 - Rear starting aerial 6 - Card reader

130664

5 - Start button

cardiagn.com
130666

7 - Electric steering column lock

130665

130667

82A-2
 ENGINE IMMOBILISER
Immobiliser system: List and location of components 82A
8 - Card

130668

cardiagn.com

82A-3
 ENGINE IMMOBILISER
Start button: Removal - Refitting 82A
REMOVAL

I - REMOVAL PREPARATION OPERATION

130672
a Remove:
- the lower covers (3) from the centre front panel
130758 (see Dashboard: Removal - Refitting) ,

cardiagn.com
a Remove the side trims (1) from the centre front pan- - the dashboard lower cover (4) on the driver's side
el. (see Dashboard: Removal - Refitting) (57A, Inte-
rior equipment),
- the glovebox (5) (see Glovebox: Removal - Refit-
ting) (57A, Interior equipment).

130673
a Remove:
130670
- the side trims (6) from the centre front panel (see
a Remove the plate (2) from the gear lever (see Cen- Dashboard: Removal - Refitting) (57A, Interior
tre console: Removal - Refitting) (57A, Interior equipment),
equipment).
- the CD changer (see 86A, Radio, CD changer:
Removal - Refitting, page 86A-14) ,
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) .

82A-4
 ENGINE IMMOBILISER
Start button: Removal - Refitting 82A
II - OPERATION FOR REMOVAL OF PART
CONCERNED

130676

a Remove the start button (9) by squeezing the clips

(10) .

cardiagn.com
REFITTING

130674 I - REFITTING OPERATION FOR PART

CONCERNED
a Remove:
- the bolts (7) , a Refit the start button on the control panel.

- the starter control panel. a Connect the start button connector.

a Refit:
- the starter control panel,
- the starter control panel bolts.

II - FINAL OPERATION
a Refit:
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) ,
- the CD changer (see 86A, Radio, CD changer:
Removal - Refitting, page 86A-14) ,
- the side trims (6) of the centre front panel (see
Dashboard: Removal - Refitting) (57A, Interior
equipment),
- the glovebox (see Glovebox: Removal - Refit-
ting) (57A, Interior equipment),
- the dashboard lower cover (4) on the driver's side
130675 (see Dashboard: Removal - Refitting) (57A, Inte-
a Disconnect the connector (8) . rior equipment),
- the lower covers (3) of the centre front panel (see
Dashboard: Removal - Refitting) (57A, Interior
equipment),
- the plate (2) of the gear lever (see Centre con-
sole: Removal - Refitting) (57A, Interior equip-
ment),

82A-5
 ENGINE IMMOBILISER
Start button: Removal - Refitting 82A
- the side trim (1) of the centre front panel.

cardiagn.com

82A-6
 ENGINE IMMOBILISER
Electric steering column lock: Removal - Refitting 82A
Equipment required

Diagnostic tool

Tightening torquesm

electric steering column 15 N.m

lock bolts

REMOVAL

I - REMOVAL PREPARATION OPERATION

a

IMPORTANT

cardiagn.com
To prevent the pyrotechnic components from
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min 130678
after disconnecting the battery. a Remove the steering wheel (2) (see Steering
wheel: Removal - Refitting) (36A, Steering assem-
a Disconnect the battery (see 80A, Battery, Battery: bly).
Removal - Refitting, page 80A-3) .

130677 130679

a Remove the driver's front airbag (1) (see 88C, Air a Remove:
bag and Pretensioners, Driver's frontal airbag:
Removal - Refitting, page 88C-10) . - the bolts (3) ,

- the cover (4) ,

- the radio control satellite (see 86A, Radio, Radio

control satellite: Removal - Refitting, page 86A-
17) ,

- the steering column lower cover.

82A-7
 ENGINE IMMOBILISER
Electric steering column lock: Removal - Refitting 82A

cardiagn.com
130680 130682

a Remove the dashboard lower cover (5) on the driv- a

er's side (see Dashboard: Removal - Refitting)
Note:
(57A, Interior equipment).
To remove the electric steering column lock, it
must be in the « unlocked » position.
II - OPERATION FOR REMOVAL OF PART
CONCERNED a Remove the electric steering column lock (8) .

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

a Refit the electric steering column lock.

Note:
The electric steering column lock bolts are shear-
ing bolts. A tightening torque of 16 N.m will cut
off the bolt head.

a Torque tighten the electric steering column lock

bolts (15 N.m).

a Connect the electric steering column lock connector.

130681
Note:
a Disconnect the electric steering column lock con- To program the electric steering column lock, the
nector (6) . immobiliser code must be stored in the computer.

a Remove the bolts (7) from the electric steering col- Running tests with computers borrowed from the
umn lock by rotating them anticlockwise using a Parts Department or from another vehicle which
punch. must then be returned is prohibited.

82A-8
 ENGINE IMMOBILISER
Electric steering column lock: Removal - Refitting 82A
II - FINAL OPERATION
a Refit:
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment),
- the steering column lower cover,
- the radio control satellite (see 86A, Radio, Radio
control satellite: Removal - Refitting, page 86A-
17) ,
- the cover,
- the bolts,
- the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly),
- the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-10) .

cardiagn.com
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .
a When replacing the steering column electric lock,
carry out the necessary operations using the Diag-
nostic tool (see Replacement of components)
(87B, Passenger compartment connection unit).

82A-9
 ENGINE IMMOBILISER
Card reader: Removal - Refitting 82A
REMOVAL

I - REMOVAL PREPARATION OPERATION

130685
a Remove:
- the lower covers (3) from the centre front panel
130758 (see Dashboard: Removal - Refitting) ,

cardiagn.com
a Remove the side trims (1) from the centre front pan- - the dashboard lower cover (4) on the driver's side
el. (see Dashboard: Removal - Refitting) (57A, Inte-
rior equipment),
- the glovebox (5) (see Glovebox: Removal - Refit-
ting) (57A, Interior equipment).

130686
a Remove:
130684
- the side trims (6) from the centre front panel (see
a Remove the plate (2) from the gear lever (see Cen- Dashboard: Removal - Refitting) (57A, Interior
tre console: Removal - Refitting) (57A, Interior equipment),
equipment).
- the CD changer (see 86A, Radio, CD changer:
Removal - Refitting, page 86A-14) ,
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) .

82A-10
 ENGINE IMMOBILISER
Card reader: Removal - Refitting 82A
II - OPERATION FOR REMOVAL OF PART
CONCERNED

130689

a Remove:

- the card reader bolts (9) ,

cardiagn.com
- the card reader.

130687 REFITTING
a Remove:
- the starter control panel bolts (7) , I - REFITTING OPERATION FOR PART
CONCERNED
- the starter control panel.
a Refit:

- the card reader,

- the card reader bolts.

a Connect the card reader connector.

a Refit:

- the starter control panel,

- the starter control panel bolts.

II - FINAL OPERATION

a Refit:

- the radio (see 86A, Radio, Radio: Removal - Re-

fitting, page 86A-4) ,

- the CD changer (see 86A, Radio, CD changer:

Removal - Refitting, page 86A-14) ,
130688 - the side trims (6) of the centre front panel (see
a Disconnect the connector (8) . Dashboard: Removal - Refitting) (57A, Interior
equipment),

- the glovebox (see Glovebox: Removal - Refit-

ting) (57A, Interior equipment),
- the dashboard lower cover (4) on the driver's side
(see Dashboard: Removal - Refitting) (57A, Inte-
rior equipment),

82A-11
 ENGINE IMMOBILISER
Card reader: Removal - Refitting 82A
- the lower covers (3) of the centre front panel (see
Dashboard: Removal - Refitting) (57A, Interior
equipment),
- the plate (2) of the gear lever (see Centre con-
sole: Removal - Refitting) (57A, Interior equip-
ment),
- the side trims (1) of the centre front panel.

cardiagn.com

82A-12
 ENGINE IMMOBILISER
Starting aerial: Removal - Refitting 82A
REMOVAL - the starter control panel (see 82A, Engine immo-
biliser, Card reader: Removal - Refitting, page
82A-10) ,
I - REMOVAL PREPARATION OPERATION
- the glovebox (see Glovebox: Removal - Refit-
ting) (57A, Interior equipment),
1 - Front starting aerial
- the central console (see Centre console: Remov-
a al - Refitting) (57A, Interior equipment),
IMPORTANT - the dashboard (see Dashboard: Removal - Refit-
To prevent the pyrotechnic components from ting) (57A, Interior equipment).
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min
after disconnecting the battery.

a Disconnect the battery (see 80A, Battery, Battery:

Removal - Refitting, page 80A-3) .
a Remove:
- the driver's front airbag (see 88C, Air bag and Pre-

cardiagn.com
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-10) ,
- the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly),
- the radio control satellite (see 86A, Radio, Radio
control satellite: Removal - Refitting, page 86A-
17) ,
- the half cowlings (see Steering column: Removal
- Refitting) (36A, Steering assembly),
- the rotary switch (see 84A, Control - Signals, Ro- 130690
tary switch: Removal - Refitting, page 84A-2) , a Remove:
- the steering column switch assembly (see 84A, - the bolts (1) ,
Control - Signals, Steering column switch as-
sembly: Removal - Refitting, page 84A-4) , - the rear air distribution duct (2) .

- the instrument panel (see 83A, Instrument panel,

Instrument panel: Removal - Refitting, page 2 - Central starting aerial
83A-1) , a Remove the centre console (see Centre console:
Removal - Refitting) (57A, Interior equipment).
- the front centre speaker (see 86A, Radio, Front
speakers: Removal - Refitting, page 86A-11) ,
- the display (see 86A, Radio, Display: Removal -
Refitting, page 86A-15) ,
- the tweeter (see 86A, Radio, Tweeter: Removal -
Refitting, page 86A-10) ,
- the solar radiation detector (see Solar radiation
sensor: Removal - Refitting) ,
- the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) ,
- the control panel (see Control panel: Removal -
Refitting) (61A, Heating),

82A-13
 ENGINE IMMOBILISER
Starting aerial: Removal - Refitting 82A
3 - Rear starting aerial II - OPERATION FOR REMOVAL OF PART
CONCERNED

1 - Front starting aerial

130691
a Remove:
- the luggage compartment front centre floor trim (3)

cardiagn.com
(see Luggage compartment floor lining: Re-
moval - Refitting) (71A, Body internal trim),
- the luggage compartment front floor trim (4) (see
Luggage compartment floor lining: Removal -
Refitting) (71A, Body internal trim).
130692
a Remove:
- the mounting clips (5) ,
- the front starting aerial (6) .
a Disconnect the front starting aerial connector.

82A-14
 ENGINE IMMOBILISER
Starting aerial: Removal - Refitting 82A
2 - Central starting aerial REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

1 - Front starting aerial

a Connect the front starting aerial connector.
a Refit:
- the front starting aerial,
- the mounting clips.

2 - Central starting aerial

a Connect the front starting aerial connector.
a Refit:

cardiagn.com
- the central starting aerial,
- the mounting clips.
130693

a Remove: 3 - Rear starting aerial

- the mounting clips (7) , a Connect the front starting aerial connector.
- the central starting aerial (8) . a Refit:
a Disconnect the front starting aerial connector. - the rear starting aerial,
- the mounting clips.
3 - Rear starting aerial

II - FINAL OPERATION.

1 - Front starting aerial

a Refit:
- the rear air distribution duct,
- the rear air distribution duct bolts,
- the dashboard (see Dashboard: Removal - Refit-
ting) (57A, Interior equipment).
- the central console (see Centre console: Remov-
al - Refitting) (57A, Interior equipment),
- the glovebox (see Glovebox: Removal - Refit-
130694 ting) (57A, Interior equipment),
a Remove:
- the starter control panel (see 82A, Engine immo-
- the mounting clips (9) , biliser, Card reader: Removal - Refitting, page
82A-10) ,
- the rear starting aerial (10) .
- the control panel (see Control panel: Removal -
a Disconnect the front starting aerial connector.
Refitting) (61A, Heating),
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) ,
- the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,

82A-15
 ENGINE IMMOBILISER
Starting aerial: Removal - Refitting 82A
- the solar radiation detector (see Solar radiation
sensor: Removal - Refitting) ,

- the tweeter (see 86A, Radio, Tweeter: Removal -

Refitting, page 86A-10) ,

- the display (see 86A, Radio, Display: Removal -

Refitting, page 86A-15) ,

- the front centre speaker (see 86A, Radio, Front

speakers: Removal - Refitting, page 86A-11) ,

- the instrument panel (see 83A, Instrument panel,

Instrument panel: Removal - Refitting, page
83A-1) ,

- the steering column switch assembly (see 84A,

Control - Signals, Steering column switch as-
sembly: Removal - Refitting, page 84A-4) ,

cardiagn.com
- the rotary switch (see 84A, Control - Signals, Ro-
tary switch: Removal - Refitting, page 84A-2) ,

- the half cowlings (see Steering column: Removal

- Refitting) (36A, Steering assembly),

- the radio control satellite (see 86A, Radio, Radio

control satellite: Removal - Refitting, page 86A-
17) ,

- the steering wheel (see Steering wheel: Removal

- Refitting) (36A, Steering assembly),

- the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-10) .

a Connect the battery (see 80A, Battery, Battery: Re-

moval - Refitting, page 80A-3) .

2 - Central starting aerial

a Refit the centre console (see Centre console: Re-

moval - Refitting) (57A, Interior equipment).

3 - Rear starting aerial

a Refit:

- the luggage compartment front floor trim (see Lug-

gage compartment floor lining: Removal - Refit-
ting) (71A, Body internal trim),

- the luggage compartment front centre floor trim

(see Luggage compartment floor lining: Re-
moval - Refitting) (71A, Body internal trim).

82A-16
 ENGINE IMMOBILISER
Battery for remote door locking control: Removal - Refitting 82A
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

130696
a Refit:
- the door locking remote control battery (3) using a
flat-blade screwdriver,

cardiagn.com
130695
- the door locking remote control battery cover,
a Remove:
- the emergency key.
- the emergency key (1) ,
- the battery cover (2) from the door locking remote
control using a flat-blade screwdriver,
- the door locking remote control battery.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a

WARNING
To ensure that the remote control operates cor-
rectly, take care not to damage the battery con-
tacts.
Only handle the new battery with dry, grease-free
hands or wearing clean gloves to avoid any risk
of dirt and oxidation on the battery.

82A-17
 HORN
Audible warning: Removal - Refitting 82B
Tightening torquesm

audible warning bolts 21 N.m

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the front bumper (see Front bumper: Re-

moval - Refitting) (55A, Exterior protection).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130839

a Disconnect the audible warning connectors (1) .

a Remove:

- the audible warning bolts (2) ,

- the audible warnings.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

a Refit the audible warnings.

a Torque tighten the audible warning bolts (21 N.m).

a Connect the audible warning connectors.

II - FINAL OPERATION.

a Refit the front bumper (see Front bumper: Remov-

al - Refitting) (55A, Exterior protection).

82B-1
 ALARM
Alarm: List and location of components 82C
ALARM 01
I - LIST OF COMPONENTS 3 - Instrument panel buzzer

No. Description

(1) Front parking distance control buzzer

(2) Rear parking distance control buzzer

(3) Instrument panel buzzer

II - POSITION OF THE COMPONENTS

1 - Front parking distance control buzzer

131493

cardiagn.com
131491

2 - Rear parking distance control buzzer

131492

82C-1
 ALARM
Bonnet switch: Removal - Refitting 82C
ALARM 01

REMOVAL

REMOVAL OF PART CONCERNED

cardiagn.com
131362
a Disconnect the connector (1) from the bonnet
switch.
a Remove:
- the bonnet switch bolt (2) ,
- the bonnet switch with the support.

REFITTING

REFITTING PART CONCERNED

a Refit:
- the bonnet switch with the support,
- the bonnet switch bolt.
a Connect the bonnet switch connector.

82C-2
 ALARM
Anti-intrusion alarm sensor: Removal - Refitting 82C
ALARM 01

REMOVAL

REMOVAL OF PART CONCERNED

cardiagn.com
131363
a Unclip the cover (1) from the anti-intrusion alarm
sensor. 131365
a Remove:
- the anti-intrusion alarm sensor bolts (3) ,
- the anti-intrusion alarm sensor.

REFITTING

REFITTING PART CONCERNED

a Refit:
- the anti-intrusion sensor,
- the anti-intrusion sensor bolts,
- the headlining (see Headlining: Removal - Refit-
131364 ting) (71A, Body internal trim).
a Unclip:
a Clip:
- the anti-intrusion alarm sensor detector clips (2) ,
- the anti-intrusion alarm sensor detector on the cov-
- the anti-intrusion alarm sensor detector from the er,
cover.
- the anti-intrusion alarm sensor detector clips,
a Remove the headlining (see Headlining: Removal -
- the anti-intrusion alarm sensor cover.
Refitting) (71A, Body internal trim).

82C-3
 INSTRUMENT PANEL
Instrument panel: Removal - Refitting 83A
Equipment required

Diagnostic tool

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-3) .

Note:
130698
The steering wheel does not need to be
removed. a Remove the top of the instrument panel trim in the
direction of the arrow (4) .

cardiagn.com
II - OPERATION FOR REMOVAL OF PART
CONCERNED

130699

130697 a Remove the bolts (5) from the instrument panel.

a Remove the bolts (1) .
a Unclip the clips (2) .
a Remove the bottom of the instrument panel trim in
the direction of the arrows (3) .

130700

a Remove the instrument panel.

a Disconnect the connectors (6) from the instrument

panel.

83A-1
 INSTRUMENT PANEL
Instrument panel: Removal - Refitting 83A
REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Connect the connectors to the instrument panel.
a Refit:
- the instrument panel,
- the instrument panel bolts,
- the instrument panel trim.
a Clip the clips onto the upper half cowling.
a Refit the instrument panel trim bolts.

II - FINAL OPERATION.
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

cardiagn.com
a When replacing the instrument panel, carry out the
necessary operations using the Diagnostic tool
(see Fault finding - Replacement of components)
(83A, Instrument panel).

83A-2
 INSTRUMENT PANEL
Vehicle position sensor: Removal - Refitting 83A
REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the headlining (see Headlining: Removal -
Refitting) (71A, Body internal trim).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130374
a Disconnect the vehicle location sensor connector (1)
.
a Remove:
- the vehicle location sensor bolts (2) ,
- the vehicle location sensor.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit:
- the vehicle location sensor,
- the vehicle location sensor bolts.
a Connect the vehicle location sensor connector.

II - FINAL OPERATION.
a Refit the headlining (see Headlining: Removal -
Refitting) (71A, Body internal trim).

83A-3
 ON-BOARD TELEMATICS SYSTEM
Navigation: List and location of components 83C
NAVIGATION AID 1 or NAVIGATION AID 2 or NAVIGATION AID 4
3 - Navigation aerial

I - LIST OF COMPONENTS

No. Description

(1) Navigation screen

(2) Navigation computer

(3) Navigation aerial

(4) Navigation interface unit

(5) Central control 130703

II - LOCATION OF COMPONENTS 4 - Navigation interface unit

cardiagn.com
1 - Navigation screen

130704

130701 5 - Central control

2 - Navigation computer

130702

130705

83C-1
 ON-BOARD TELEMATICS SYSTEM
Radio navigation: Removal - Refitting 83C
NAVIGATION AID 1
II - OPERATION FOR REMOVAL OF PART
Special tooling required CONCERNED
Ms. 1373 Tool for removing radios or
chronotachographs.

REMOVAL

I - REMOVAL PREPARATION OPERATION

130707

cardiagn.com
130758
a Remove the centre front panel side trim (1) .

130708
a Remove the radio navigation system using tool (Ms.
1373) (2) .
a Disconnect the connectors.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Connect the connectors.
a Refit the radio navigation system.

II - FINAL OPERATION
a Refit the centre front panel side trim.

83C-2
 ON-BOARD TELEMATICS SYSTEM
Navigation computer: Removal - Refitting 83C
NAVIGATION AID 1 or NAVIGATION AID 2 or NAVIGATION AID 4

REMOVAL

I - REMOVAL PREPARATION OPERATION

130711
a Disconnect the connectors (3) .
a Remove the navigation computer (4) .

cardiagn.com
130709
a Remove the glovebox (1) (see Glovebox: Removal
REFITTING
- Refitting) (57A, Interior equipment).

I - REFITTING OPERATION FOR PART

II - OPERATION FOR REMOVAL OF PART
CONCERNED
CONCERNED
a Connect the navigation computer connectors.
a Refit:
- the navigation computer,
- the navigation computer bolts.

II - FINAL OPERATION.
a Refit the glovebox (see Glovebox: Removal - Refit-
ting) (57A, Interior equipment).

130710
a Remove the bolts (2) .

83C-3
 ON-BOARD TELEMATICS SYSTEM
Navigation interface unit: Removal - Refitting 83C
NAVIGATION AID 1 or NAVIGATION AID 2 or NAVIGATION AID 4

REMOVAL II - OPERATION FOR REMOVAL OF PART

CONCERNED

I - REMOVAL PREPARATION OPERATION

130721
a Disconnect the connector (3) .

cardiagn.com
130719
a Remove the glovebox (1) (see Glovebox: Removal a Unclip the navigation interface unit at (4) .
- Refitting) (57A, Interior equipment).
REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Clip on the navigation interface unit.
a Connect the navigation interface unit connector.

II - FINAL OPERATION.
a Refit:
- the navigation computer bolts,
- the glovebox (see Glovebox: Removal - Refit-
130720 ting) (57A, Interior equipment).
a Remove the bolts (2) from the navigation computer.

83C-4
 ON-BOARD TELEMATICS SYSTEM
Central control: Removal - Refitting 83C
NAVIGATION AID 2 or NAVIGATION AID 4

REMOVAL II - OPERATION FOR REMOVAL OF PART

CONCERNED

I - REMOVAL PREPARATION OPERATION

cardiagn.com
130713

130712
a Disconnect the connector from the central control.

a Remove the centre console (1) (see Centre con- a Remove:

sole: Removal - Refitting) (57A, Interior equip- - the bolts (2) ,
ment).
- the central control (3) .

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit:
- the central control,
- the central control bolts.
a Connect the connector to the central control.

II - FINAL OPERATION.
a Refit the centre console (see Centre console: Re-
moval - Refitting) (57A, Interior equipment).

83C-5
 ON-BOARD TELEMATICS SYSTEM
Navigation screen: Removal - Refitting 83C
NAVIGATION AID 1 or NAVIGATION AID 2 or NAVIGATION AID 4

REMOVAL

I - REMOVAL PREPARATION OPERATION

130716
a Remove the navigation screen protector (4) using a
flat-blade screwdriver.

cardiagn.com
130714
a Remove the front centre speaker trim (1) . II - OPERATION FOR REMOVAL OF PART
CONCERNED

130715
130717
a Remove:
a Remove the bolts (5) .
- the front centre speaker cover bolts (2) ,
- the front centre speaker cover (3) .

83C-6
 ON-BOARD TELEMATICS SYSTEM
Navigation screen: Removal - Refitting 83C
NAVIGATION AID 1 or NAVIGATION AID 2 or NAVIGATION AID 4

130718
a Remove the navigation screen.
a Disconnect the connector (6) .

cardiagn.com
REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Connect the connector.
a Refit:
- the navigation screen,
- the navigation screen bolts.

II - FINAL OPERATION.
a Refit:
- the navigation screen protector,
- the front centre speaker cover,
- the front centre speaker cover bolts,
- the front centre speaker trim.

83C-7
 ON-BOARD TELEMATICS SYSTEM
Navigation aerial: Removal - Refitting 83C
NAVIGATION AID 1 or NAVIGATION AID 2 or NAVIGATION AID 4

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove:
- the glovebox (see Glovebox: Removal - Refit-
ting) (57A, Interior equipment),
- the navigation computer (see 8 3 C, On-board
telematics system, Navigation computer: Re-
moval - Refitting, page 83C-3) .

130724
a Disconnect the connector (3) .

cardiagn.com
Note:
Use a rope to remove and refit the navigation
aerial wiring.

130722
a Remove the rear section of the dashboard cover (1)
.

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130725
a Secure the navigation aerial wiring using a rope (4) .

130723
a Remove the navigation aerial bolts (2) .

83C-8
 ON-BOARD TELEMATICS SYSTEM
Navigation aerial: Removal - Refitting 83C
NAVIGATION AID 1 or NAVIGATION AID 2 or NAVIGATION AID 4

cardiagn.com
130726

a Remove:

- the dashboard navigation aerial wiring by pulling it

from the dashboard,

- the navigation aerial.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

a Refit:

- the navigation aerial,

- the navigation aerial wiring inside the dashboard by

pulling the rope under the dashboard.

a Detach the rope.

a Connect the connector.

a Refit the navigation aerial bolts.

II - FINAL OPERATION

a Refit:

- the rear section of the dashboard cover,

- the navigation computer (see 8 3 C, On-board

telematics system, Navigation computer: Re-
moval - Refitting, page 83C-3) ,

- the glovebox (see Glovebox: Removal - Refit-

ting) .

83C-9
 CRUISE CONTROL
Cruise control - speed limiter: List and location of components 83D
CRUISE CONTROL
I - LIST OF COMPONENTS 3 - Brake switch

No. Description

(1) Switch

(2) Steering column switches

(3) Brake switch

(4) Clutch switch

II - LOCATION OF COMPONENTS

1 - Switch

cardiagn.com
130377

4 - Clutch switch

130375

2 - Steering column switches

130378

130376

83D-1
 CRUISE CONTROL
Switch: Removal - Refitting 83D
CRUISE CONTROL

REMOVAL

I - REMOVAL PREPARATION OPERATION

131580
a Remove:
- the centre front panel lower covers (3) on both

cardiagn.com
130758 sides,
a Remove the centre front panel side trim (1) . - the glovebox (see Glovebox: Removal - Refit-
ting) ( 57A, Interior equipment),
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment).

131581
131579 a Remove:
a Remove the plate (2) from the gear lever (see Cen- - the centre front panel side trims (4) on both sides,
tre console: Removal - Refitting) (57A, Interior
equipment). - the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) .

83D-2
 CRUISE CONTROL
Switch: Removal - Refitting 83D
CRUISE CONTROL
a Connect the connectors.
a Refit:
- the starter control panel,
- the starter control panel bolts.

II - FINAL OPERATION.
a Refit:
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) ,
- the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the centre front panel side trims on both sides,
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment),

cardiagn.com
- the glovebox (see Glovebox: Removal - Refit-
131582 ting) ( 57A, Interior equipment),
a Remove: - the centre front panel lower covers on both sides,
- the starter control panel bolts (5) , - the gear lever plate (see Centre console: Remov-
al - Refitting) (57A, Interior equipment),
- the starter control panel.
- the centre front panel side trim.
a Disconnect the connectors.

II - OPERATION FOR REMOVAL OF PART

CONCERNED

131570
a Unclip the switch clips (6) .
a Remove the switch.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit the switch on the control panel.

83D-3
 CRUISE CONTROL
Steering wheel switch: Removal - Refitting 83D
CRUISE CONTROL

REMOVAL

I - REMOVAL PREPARATION OPERATION

a

IMPORTANT
To prevent the pyrotechnic components from
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min
after disconnecting the battery.

a Disconnect the battery (see 80A, Battery, Battery:

Removal - Refitting, page 80A-3) .
a Remove:
- the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-10) ,

cardiagn.com
- the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly).
130380

a Remove:
II - OPERATION FOR REMOVAL OF PART
CONCERNED - the bolts (3) from the steering column switches,

- the steering column switches.

REFITTING

I - REFITTING PREPARATION OPERATION

a Always replace the steering wheel nut.

II - REFITTING OPERATION FOR PART

CONCERNED

a Refit:
- the steering column switches,
130379
a Unclip the steering wheel rear cover clips (1) . - the steering column switch bolts,
a Remove the steering wheel rear cover (2) from the - the steering wheel rear cover on the steering
steering wheel. wheel.

III - FINAL OPERATION.

a Refit:
- the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly),

- the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-10) .
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

83D-4
 CONTROL - SIGNALS
Steering column switch assembly: List and location of components 84A
I - LIST OF COMPONENTS 2 - Steering column switch assembly

No. Description

(1) UCH

(2) Wiper stalk

(3) Lighting stalk

(4) Telephone/radio control satellite

II - LOCATION OF COMPONENTS

1 - UCH

cardiagn.com
130382

(2) Wiper stalk

(3) Lighting stalk
(4) Telephone/radio control satellite

130381
The UCH (1) is located in the dashboard, behind the
passenger compartment relay unit. To remove it (see
87B, Passenger compartment connection unit,
UCH: Removal - Refitting, page 87B-1) .

84A-1
 CONTROL - SIGNALS
Rotary switch: Removal - Refitting 84A
REMOVAL

I - REMOVAL PREPARATION OPERATION

a Set the wheels straight ahead.

IMPORTANT
To prevent the pyrotechnic components from
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min
after disconnecting the battery.

a Disconnect the battery (see 80A, Battery, Battery:

Removal - Refitting, page 80A-3) .

a Remove:

- the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -

cardiagn.com
Refitting, page 88C-10) ,
130384
- the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly). a Remove:

- the radio control satellite nut (4) ,

II - OPERATION FOR REMOVAL OF PART
CONCERNED - the radio control satellite (5) .

a Disconnect the radio control satellite connector.

a Unclip the lower half of the cover (6) under the steer-
ing wheel.

130383

a Remove the bolts (1) from the cover under the steer-
ing wheel.

a Unclip: 130385

- the upper half of the cover (2) under the steering a Remove the rotary switch bolts (7) .
wheel,
a Unclip the rotary switch.
- the lower half of the cover (3) under the steering
wheel. a Disconnect the rotary switch connectors (8) .

84A-2
 CONTROL - SIGNALS
Rotary switch: Removal - Refitting 84A
REFITTING - the radio control satellite nut,
- the lower half of the cover under the steering
I - REFITTING PREPARATION OPERATION wheel,

a Always replace the steering wheel nut. - the upper half of the cover under the steering
wheel,
- the bolts of the cover under the steering wheel.
II - REFITTING OPERATION FOR PART
CONCERNED
III - FINAL OPERATION.
a
a Refit:
WARNING
- the steering wheel (see Steering wheel: Removal
To prevent damaging the rotary switch, do not
- Refitting) (36A, Steering assembly),
turn the mobile section of the rotary switch.
- the driver's front airbag (see 88C, Air bag and Pre-
a Connect the rotary switch connectors. tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-10) .
a Refit:
a Connect the battery (see 80A, Battery, Battery: Re-
- the rotary switch, moval - Refitting, page 80A-3) .

cardiagn.com
- the rotary switch bolts.

130386
a Adjust the neutral position of the rotary switch:
- turn the rotary switch carefully clockwise as far as it
will go,
- turn the rotary switch anticlockwise (approximately
two and a half turns),

- stop rotating at (A) .

a Refit the lower half of the cover under the steering
wheel.
a Connect the radio control satellite connector.
a Refit:
- the radio control satellite,

84A-3
 CONTROL - SIGNALS
Steering column switch assembly: Removal - Refitting 84A
REMOVAL II - REFITTING OPERATION FOR PART
CONCERNED

I - REMOVAL PREPARATION OPERATION a Refit the steering column switch assembly.

a Connect the steering column switch assembly con-
a Set the wheels straight ahead.
nectors.

IMPORTANT III - FINAL OPERATION.

To prevent the pyrotechnic components from a Refit:
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min - the rotary switch (see 84A, Control - Signals, Ro-
after disconnecting the battery. tary switch: Removal - Refitting, page 84A-2) ,
- the steering wheel (see Steering wheel: Removal
a Disconnect the battery (see 80A, Battery, Battery: - Refitting) (36A, Steering assembly),
Removal - Refitting, page 80A-3) .
- the driver's front airbag (see 88C, Air bag and Pre-
a Remove: tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-10) .
- the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal - a Connect the battery (see 80A, Battery, Battery: Re-

cardiagn.com
Refitting, page 88C-10) , moval - Refitting, page 80A-3) .

- the steering wheel (see Steering wheel: Removal

- Refitting) (36A, Steering assembly),

- the rotary switch. (see 84A, Control - Signals, Ro-

tary switch: Removal - Refitting, page 84A-2)

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130387

a Disconnect the steering column switch assembly

connectors (1) .

a Remove the steering column switch assembly by

pulling it in the direction of the arrow (2) .

REFITTING

I - REFITTING PREPARATION OPERATION

a Always replace the steering wheel nut.

84A-4
 CONTROL - SIGNALS
Hazard warning lights and central door control: Removal - Refitting 84A
Special tooling required

Car. 1363 Set of trim removal levers.

Note:
The hazard warning light switch and the central
door locking switch constitute a single part.

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the control panel (see Control panel: Re-
moval - Refitting) (61A, Heating).

II - OPERATION FOR REMOVAL OF PART

cardiagn.com
CONCERNED
130389
a Unclip the clips (2) on both sides.
a Remove the hazard warning lights switch (3) .

130388
a Remove the hazard warning light and central door
locking switches (1) using the tool (Car. 1363).
a Disconnect the hazard warning light and central
door locking switch connectors.

130390
a Unclip the clips (4) on both sides.
a Remove the central door locking switch (5) .

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit:
- the central door locking switch,

84A-5
 CONTROL - SIGNALS
Hazard warning lights and central door control: Removal - Refitting 84A
- the hazard warning light switch.
a Connect the hazard warning light and central door
locking switch connectors.

II - FINAL OPERATION.
a Refit the control panel (see Control panel: Remov-
al - Refitting) (61A, Heating).

cardiagn.com

84A-6
 CONTROL - SIGNALS
ESP inhibitor switch: Removal - Refitting 84A
ELECTRONIC STABILITY PROGRAM 2 or ELECTRONIC STABILITY PROGRAM

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the dashboard lower cover on the driver's
side (see Dashboard: Removal - Refitting) (57A,
Interior equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130391
a Unclip the ESP inhibitor switch (1) from the dash-
board lower cover.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit the ESP inhibitor switch on the dashboard low-
er cover.

II - FINAL OPERATION.
a Refit the dashboard lower cover on the driver's side
(see Dashboard: Removal - Refitting) (57A, Interi-
or equipment).

84A-7
 CONTROL - SIGNALS
Remote headlight beam adjustment control: Removal - Refitting 84A
REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the dashboard lower cover on the driver's
side (see Dashboard: Removal - Refitting) (57A,
Interior equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
132647
a Unclip the remote headlight beam adjustment con-
trol (1) from the dashboard lower cover.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit the remote headlight beam adjustment control
on the dashboard lower cover.

II - FINAL OPERATION.
a Refit the dashboard lower cover on the driver's side
(see Dashboard: Removal - Refitting) (57A, Interi-
or equipment).

84A-8
 CONTROL - SIGNALS
Lighting dimmer: Removal - Refitting 84A
REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the dashboard lower cover on the driver's
side (see Dashboard: Removal - Refitting) (57A,
Interior equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130392
a Unclip the lighting dimmer (1) from the dashboard
lower cover.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit the lighting dimmer on the dashboard lower
cover.

II - FINAL OPERATION.
a Refit the dashboard lower cover on the driver's side
(see Dashboard: Removal - Refitting) (57A, Interi-
or equipment).

84A-9
 CONTROL - SIGNALS
Exterior rear view mirror control switch: Removal - Refitting 84A
Special tooling required
REFITTING

Car. 1363 Set of trim removal levers. REFITTING OPERATION FOR PART CONCERNED
a Connect the door mirror control switch connector.
REMOVAL a Refit:
- the door mirror control switch on the front door han-
OPERATION FOR REMOVAL OF PART dle trim,
CONCERNED
- the front door handle trim.

cardiagn.com
130393
a Remove the front door handle trim (1) using the tool
(Car. 1363) (2) .

130394
a Disconnect the door mirror control switch connector
(3) .
a Remove the door mirror control switch (4) from the
front door handle trim.

84A-10
 CONTROL - SIGNALS
Heated rear screen: Repair 84A
The screen printed heated grid on the inner face of the
window may have an accidental cut, making the affect-
ed part of the circuit useless.
a Determine the exact location of the cut using a volt-
meter.
Faults such as these can be repaired by using the
heated rear screen varnish available at the. Maga-
sin Pièce de Rechange

I - DETERMINING THE EXACT LOCATION OF THE

CUT USING A VOLTMETER
a Switch on the ignition.
a Press the heated rear screen switch. 130396
a A sudden voltage drop indicates that the filament is
1 - Detection between lines B and A cut at that point (repeat this operation for each fila-
ment).
a Connect the + wire of the voltmeter to the + feed ter-

cardiagn.com
minal of the rear screen.
II - REPAIRING THE FILAMENT
a Put the - wire of the voltmeter on a filament at the -
terminal side of the rear screen (line A); the voltage a Clean the section to be repaired to remove all dust
obtained should be roughly equal to that of the bat- or grease, preferably using alcohol or a glass clean-
tery. er, and wipe with a clean, dry cloth.
a Move the - wire towards line A (see arrow): the volt- a To ensure that the new line is straight, before var-
age gradually drops. nishing, apply adhesive tape to either side of the
section to be repaired, leaving the conducting line
exposed.
a Before using the varnish, shake the bottle to prevent
the silver particles settling at the bottom.

Repair
a Carry out the repair using a small brush, applying a
sufficiently thick layer. If applying successive coats,
allow sufficient drying time between each coat and
do not repeat the operation more than three times.
a Any varnish that runs over can be removed using a
knife, but only after several hours of drying.

130395

a A sudden voltage drop indicates that the filament is

cut at that point (repeat this operation for each fila-
ment).

2 - Detection between lines C and A

a Connect the - wire of the voltmeter to the - terminal
of the rear screen.
a Put the + wire of the voltmeter on the filament at the
+ terminal end of the rear screen (line C); the voltage
obtained should be roughly equal to battery voltage.
a Move the + wire towards line A (see arrow): the volt-
age gradually drops.

84A-11
 CONTROL - SIGNALS
Heated rear screen: Repair 84A

cardiagn.com
130397
a The adhesive tape used as a guide must not be re-
moved until approximately one hour after applica-
tion. The tape must be pulled off perpendicularly to
the resistance, in the direction of the arrow. Varnish
applied at an ambient temperature of 20˚C will be
completely dry in three hours. At lower tempera-
tures, the drying time is slightly longer.

84A-12
 CONTROL - SIGNALS
Heated seat pad switch: Removal - Refitting 84A
FRONT SEAT WITH HEATING

REMOVAL REFITTING

I - REMOVAL PREPARATION OPERATION I - REFITTING OPERATION FOR PART

CONCERNED
a
a Refit:
Note:
- the heated seat cover switch,
It is not necessary to remove the front seat com-
pletely. - the heated seat cover switch bolts.
a Connect the heated seat cover switch connector.
a Move the seat as far forward as possible.
II - FINAL OPERATION.
a Refit the front seat lower cover on the side con-
cerned (see Front seat base trim: Removal - Refit-
ting) (77A, Front seat trim).

cardiagn.com
130398

a Remove the front seat lower cover (1) on the side

concerned (see Front seat base trim: Removal -
Refitting) (77A, Front seat trim).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130399

a Disconnect the connector (2) from the heated seat

cover switch.
a Remove:
- the heated seat cover switch bolts (3) ,
- the heated seat cover switch (4) .

84A-13
 CONTROL - SIGNALS
Hill descent control system: Removal - Refitting 84A
ELECTRONIC STABILITY PROGRAM 2

REMOVAL

I - REMOVAL PREPARATION OPERATION

131580
a Remove:
- the centre front panel lower covers (3) on both

cardiagn.com
130758 sides,
a Remove the centre front panel side trim (1) . - the glovebox (see Glovebox: Removal - Refit-
ting) ( 57A, Interior equipment),
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment).

131581
131579 a Remove:
a Remove the plate (2) from the gear lever (see Cen- - the centre front panel side trims (4) on both sides,
tre console: Removal - Refitting) (57A, Interior
equipment). - the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) .

84A-14
 CONTROL - SIGNALS
Hill descent control system: Removal - Refitting 84A
ELECTRONIC STABILITY PROGRAM 2
II - OPERATION FOR REMOVAL OF PART a Connect the connectors.
CONCERNED
a Refit:
- the starter control panel,
- the starter control panel bolts.

II - FINAL OPERATION.
a Refit:
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) ,
- the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the centre front panel side trims on both sides,
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment),

cardiagn.com
- the glovebox (see Glovebox: Removal - Refit-
ting) ( 57A, Interior equipment),
- the centre front panel lower covers on both sides,
131582
- the gear lever plate (see Centre console: Remov-
a Remove:
al - Refitting) (57A, Interior equipment),
- the starter control panel bolts (5) ,
- the centre front panel side trim.
- the starter control panel.
a Disconnect the connectors.

131577

a Unclip the clips (6) of the hill descent control switch.

a Remove the hill descent control switch.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit the hill descent control switch on the control
panel.

84A-15
 CONTROL - SIGNALS
Transmission mode management control: Removal - Refitting 84A
4X4 TRANSMISSION

REMOVAL

I - REMOVAL PREPARATION OPERATION

131580
a Remove:
- the centre front panel lower covers (3) on both

cardiagn.com
130758 sides,
a Remove the centre front panel side trim (1) . - the glovebox (see Glovebox: Removal - Refit-
ting) ( 57A, Interior equipment),
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment).

131581
131579 a Remove:
a Remove the plate (2) from the gear lever (see Cen- - the centre front panel side trims (4) on both sides,
tre console: Removal - Refitting) (57A, Interior
equipment). - the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) .

84A-16
 CONTROL - SIGNALS
Transmission mode management control: Removal - Refitting 84A
4X4 TRANSMISSION
II - OPERATION FOR REMOVAL OF PART a Connect the connectors.
CONCERNED
a Refit:
- the starter control panel,
- the starter control panel bolts.

II - FINAL OPERATION.
a Refit:
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) ,
- the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the centre front panel side trims on both sides,
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment),

cardiagn.com
- the glovebox (see Glovebox: Removal - Refit-
ting) ( 57A, Interior equipment),
- the centre front panel lower covers on both sides,
131582
- the gear lever plate (see Centre console: Remov-
a Remove:
al - Refitting) (57A, Interior equipment),
- the starter control panel bolts (5) ,
- the centre front panel side trim.
- the starter control panel.
a Disconnect the connectors.

131583

a Unclip the transmission mode switch clips (6) .

a Remove the transmission mode switch.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit the transmission mode switch on the starter
control panel.

84A-17
 WIPING - WASHING
Wiping and washing: List and location of components 85A
I - LIST OF COMPONENTS 2 - UCH

No. Description

(1) Wiper stalk

(2) UCH

(3) Passenger compartment fuse and relay

box

(4) Windscreen wiper blade

(5) Windscreen wiper blade arm

(6) Windscreen wiper mechanism

130401
(7) Windscreen wiper motor
The UCH is located in the dashboard, behind the pas-
(8) Windscreen wiper jet senger compartment fuse and relay box. To remove it

cardiagn.com
(see 87B, Passenger compartment connection unit,
(9) Rear screen wiper blade UCH: Removal - Refitting, page 87B-1) .

(10) Rear screen wiper blade arm

3 - Passenger compartment fuse and relay box
(11) Rear screen wiper motor

(12) Rear screen wiper jet

(13) Windscreen washer bottle

(14) Windscreen washer pump

(15) Windscreen washer neck

(16) Rain and light sensor

II - LOCATION OF COMPONENTS

1 - Wiper stalk

130402

130400

85A-1
 WIPING - WASHING
Wiping and washing: List and location of components 85A
5 - Windscreen wiper blade arm

130406

6 - Windscreen wiper mechanism

cardiagn.com
130403

4 - Windscreen wiper blade

130425

130405

85A-2
 WIPING - WASHING
Wiping and washing: List and location of components 85A
7 - Windscreen wiper motor 9 - Rear screen wiper blade

cardiagn.com
130407 130409

The windscreen wiper motor is incorporated into the

windscreen wiper mechanism (see 85A, Wiping - 10 - Rear screen wiper blade arm
Washing, Windscreen wiper mechanism: Removal
- Refitting, page 85A-9) .

8 - Windscreen wiper jet

130408

130410

85A-3
 WIPING - WASHING
Wiping and washing: List and location of components 85A
11 - Rear screen wiper motor 13 - Windscreen washer bottle

130411

12 - Rear screen wiper jet

cardiagn.com
130413

14 - Windscreen washer pump

130412

130414

85A-4
 WIPING - WASHING
Wiping and washing: List and location of components 85A
15 - Windscreen washer neck

130415

16 - Rain and light sensor

130416
The rain and light sensor is located underneath the in-
terior rear-view mirror covers.
cardiagn.com

85A-5
 WIPING - WASHING
Windscreen wiper blade: Removal - Refitting 85A
REMOVAL REFITTING

OPERATION FOR REMOVAL OF PART REFITTING OPERATION FOR PART CONCERNED

CONCERNED

cardiagn.com
130419
130418 a Refit the windscreen wiper blade on the end (3) of
a Press the clips (1) on both sides while turning the the wiper arm.
windscreen wiper blade in the direction of the arrow
a Clip the windscreen wiper blade onto the wind-
(2) .
screen wiper arm.
a Remove the windscreen wiper blade.

85A-6
 WIPING - WASHING
Windscreen wiper arm: Removal - Refitting 85A
Special tooling required

Ele. 1865 Tool for removing windscreen

wiper arms

Tightening torquesm

windscreen wiper arm N.m

nut24

REMOVAL
130421
I - REMOVAL PREPARATION OPERATION
a Remove the wiper arm using the (Ele. 1865) (2) .
a Switch on the ignition.

cardiagn.com
REFITTING
WARNING
To ensure that the wiper arms can travel I - REFITTING PREPARATION OPERATION
smoothly, the wiper motor must be initialised.

a Turn the wiper switch stalk from (0) to (1), and then
from (1) to (0).

a Switch off the ignition.

a Mark the position of the wiper arms for the refitting

operation.

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130422

a Clean the screen wiper arm mounting to prevent the

nut from coming loose.

II - REFITTING OPERATION FOR PART

CONCERNED

a Switch on the ignition.

WARNING
To ensure that the wiper arms can travel
130420
smoothly, the wiper motor must be initialised.
a Remove:
a Turn the wiper switch stalk from (0) to (1), and then
- the covers from the screen wiper arm nuts, from (1) to (0).

- the nuts (1) from the screen wiper arm. a Switch off the ignition.

85A-7
 WIPING - WASHING
Windscreen wiper arm: Removal - Refitting 85A
a Refit:
- the wiper arm in the position marked before remov-
al,
- the wiper arm nut.
a Torque tighten the windscreen wiper arm nut24
(N.m).
a Refit the wiper arm nut cover.

cardiagn.com

85A-8
 WIPING - WASHING
Windscreen wiper mechanism: Removal - Refitting 85A
Tightening torquesm

windscreen wiper mech- 5 N.m

anism bolts

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Switch on the ignition.

130424
WARNING
To ensure that the wiper arms can travel a Partially remove the windscreen wiper mechanism.
smoothly, the wiper motor must be initialised.
a Disconnect the windscreen wiper motor connector
(2) .

cardiagn.com
a Turn the wiper stalk from (0) to (1), and then from (1)
to (0). a Remove the windscreen wiper mechanism.

a Switch off the ignition.

REFITTING
a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-3) .
I - REFITTING OPERATION FOR PART
a Remove: CONCERNED
- the front wiper arms (see 85A, Wiping - Washing, a Connect the windscreen wiper motor connector.
Windscreen wiper arm: Removal - Refitting,
page 85A-7) , a Refit:

- the scuttle panel half-grille (see Scuttle panel half- - the windscreen wiper mechanism,
grille: Removal - Refitting) (56A, Exterior equip- - the windscreen wiper mechanism bolts.
ment).
a Torque tighten the windscreen wiper mechanism
bolts (5 N.m).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
II - FINAL OPERATION.

a Refit the scuttle panel half-grille (see Scuttle panel

half-grille: Removal - Refitting) (56A, Exterior
equipment).

a Connect the battery (see 80A, Battery, Battery: Re-

moval - Refitting, page 80A-3) .

a Switch on the ignition.

WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

130423 a Turn the wiper stalk from (0) to (1), and then from (1)
to (0).
a Remove the bolts (1) from the windscreen wiper
mechanism. a Switch off the ignition.

85A-9
 WIPING - WASHING
Windscreen wiper mechanism: Removal - Refitting 85A
a Refit the front wiper arms (see 85A, Wiping - Wash-
ing, Windscreen wiper arm: Removal - Refitting,
page 85A-7) .

cardiagn.com

85A-10
 WIPING - WASHING
Windscreen wiper motor: Removal - Refitting 85A

cardiagn.com
130425

130426
The windscreen wiper motor (1) is incorporated into the
windscreen wiper mechanism (see 85A, Wiping -
Washing, Windscreen wiper mechanism: Removal
- Refitting, page 85A-9) .

85A-11
 WIPING - WASHING
Rear screen wiper blade: Removal - Refitting 85A
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130427
a Lift the rear screen wiper arm.
a Turn the rear screen wiper arm.
a Remove the rear screen wiper blade by pulling it in
the direction of the arrow (1) .

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a Refit the rear screen wiper blade to the rear screen
wiper arm.
a Lower the rear screen wiper arm.

85A-12
 WIPING - WASHING
Rear screen wiper arm: Removal - Refitting 85A
Special tooling required

Ele. 1841 Tool for removing windscreen

wiper arms

Tightening torquesm

rear screen wiper arm 9 N.m

nut

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Switch on the ignition.

cardiagn.com
WARNING 130429
To ensure that the wiper arms can travel a Remove the nut (2) from the rear screen wiper arm.
smoothly, the wiper motor must be initialised.

a Turn the wiper stalk from (0) to (1), and then from (1)
to (0).

a Switch off the ignition.

a Mark the position of the rear screen wiper arm.

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130430
a Remove the rear screen wiper arm using the (Ele.
1841) (3) .

130428

a Open the rear screen wiper arm nut cover (1) .

85A-13
 WIPING - WASHING
Rear screen wiper arm: Removal - Refitting 85A
REFITTING

I - REFITTING PREPARATION OPERATION

130431

cardiagn.com
a Clean the rear screen wiper arm mounting to pre-
vent the nut from coming loose.

II - REFITTING OPERATION FOR PART

CONCERNED
a Switch on the ignition.

WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

a Turn the wiper stalk from (0) to (1), and then from (1)
to (0).
a Switch off the ignition.
a Refit:
- the rear screen wiper arm in the position marked
before the removal operation,
- the rear screen wiper arm nut.
a Torque tighten the rear screen wiper arm nut (9
N.m).
a Close the rear screen wiper arm nut cover.

85A-14
 WIPING - WASHING
Rear screen wiper motor: Removal - Refitting 85A
REMOVAL REFITTING

I - REMOVAL PREPARATION OPERATION I - REFITTING OPERATION FOR PART

CONCERNED
a Switch on the ignition.
a Refit:

WARNING - the rear screen wiper motor,

To ensure that the wiper arms can travel - the rear screen wiper motor bolts.
smoothly, the wiper motor must be initialised.
a Connect the rear screen wiper motor connector.
a Turn the wiper switch stalk from (0) to (1), and then
from (1) to (0). II - FINAL OPERATION.
a Switch off the ignition. a Switch on the ignition.
a Mark the position of the rear screen wiper arm.
a Remove: WARNING
- the rear screen wiper arm (see 85A, Wiping - To ensure that the wiper arms can travel
Washing, Rear screen wiper arm: Removal - Re- smoothly, the wiper motor must be initialised.

cardiagn.com
fitting, page 85A-13) ,
a Turn the wiper switch stalk from (0) to (1), and then
- the lower tailgate trim (see Tailgate trim: Removal from (1) to (0).
- Refitting) (73A, Non-side opening elements trim).
a Switch off the ignition.
a Refit:
II - OPERATION FOR REMOVAL OF PART
CONCERNED - the lower tailgate trim (see Tailgate trim: Removal
- Refitting) (73A, Non-side opening elements trim),
- the rear screen wiper arm (see 85A, Wiping -
Washing, Rear screen wiper arm: Removal - Re-
fitting, page 85A-13) .

130432
a Disconnect the rear screen wiper motor connector
(1) .
a Remove:
- the bolts (2) from the rear screen wiper motor,
- the rear screen wiper motor.

85A-15
 WIPING - WASHING
Rain and light sensor: Removal - Refitting 85A
LIGHTS + AUTOMATIC WINDSCREEN WIPER

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the covers from the interior rear-view mirror
(see Interior rear-view mirror: Removal - Refit-
ting) (57A, Interior equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

1 - Replacing the rain and light sensor

cardiagn.com
102446
a Disconnect the connector at (4) .
a Unclip:
- the two side clips (5) from the rain and light sensor
mounting using a small flat-blade screwdriver,
- the clips (6) from the printed circuit of the rain and
light sensor.

130840
a Disconnect the rain and light sensor connector (1) .
a Unclip the two side clips (2) from the rain and light
sensor (3) using a small flat-blade screwdriver,
a Separate the rain and light sensor from its mounting.

2 - Replacing the windscreen

a

Note:
The rain and light sensor mounting is supplied
with the new windscreen; remove only the rain
and light sensor.
145922
a Remove the rain and light sensor printed circuit (7)
from the rain and light sensor cover (8) .

85A-16
 WIPING - WASHING
Rain and light sensor: Removal - Refitting 85A
LIGHTS + AUTOMATIC WINDSCREEN WIPER

REFITTING II - REFITTING OPERATION FOR PART

CONCERNED

I - REFITTING PREPARATION OPERATION a

a Note:
WARNING The audible locking of the side clips fixing the
The rain sensor must be removed and refitted rain and light sensor onto its mounting on the
under conditions of extreme cleanliness: any windscreen confirm that it is correctly held and
dust or fibres may cause a fault. Do not touch the positioned.
electronic part of the sensor. Fit the sensor to the
vehicle immediately after removing it from its
packaging. Note:
To avoid damaging the adhesive base, do not
a On the inside of the windscreen, clean the inside of turn the rain and light sensor once it is positioned
the sensor mounting. on the windscreen.
a Clean the outside of the windscreen in the area cov-
ered by the rain and light sensor.
1 - Replacing the rain and light sensor

cardiagn.com
a Fit the rain and light sensor onto the mounting.
a Clip the two side clips (2) onto the rain and light sen-
sor mounting.
a Connect the connector for the rain and light sensor.

145923
a Always replace the new adhesive base with the cov-
er of the new rain and light sensor when replacing
the windscreen.

85A-17
 WIPING - WASHING
Rain and light sensor: Removal - Refitting 85A
LIGHTS + AUTOMATIC WINDSCREEN WIPER
2 - Replace the windscreen

cardiagn.com
145924

a Position:

- the new adhesive base with the new rain and light
sensor cover (9) in the rain and light sensor mount-
ing (10) ,

- the rain and light sensor printed circuit (7) onto the
rain and light sensor cover.

a Clip on:

- the clips (6) of the rain and light sensor printed cir-
cuit onto the rain and light sensor cover,

- the two side clips (5) onto the rain and light sensor
mounting.

a Connect the connector for the rain and light sensor.

III - FINAL OPERATION

a Refit the covers of the interior rear-view mirror (see

Interior rear-view mirror: Removal - Refitting)
(57A, Interior equipment).

a Carry out an operating test:

- select automatic wiping mode,

- spray droplets of water onto the windscreen within

the sensor detection area,

- check that the automatic wiping function is operat-

ing correctly.

85A-18
 WIPING - WASHING
Screen washer pump: Removal - Refitting 85A
REMOVAL II - FINAL OPERATION.
a Refit the front bumper (see Front bumper: Remov-
I - REMOVAL PREPARATION OPERATION al - Refitting) (55A, Exterior protection).

a Position the vehicle on a two-post lift (see Vehicle: a Fill-up the windscreen washer bottle.
Towing and lifting) (02A, Lifting equipment).
a Remove the front bumper (see Front bumper: Re-
moval - Refitting) (55A, Exterior protection).

II - REMOVAL OF PART CONCERNED

cardiagn.com
131366

a Place a container underneath the windscreen wash-

er bottle.
a Disconnect:
- the connector (1) from the windscreen washer
pump,
- the supply pipes (2) .

Note:
Mark the routing of the supply pipes and wiring.

a Remove the windscreen washer pump.

REFITTING

I - REFITTING PART CONCERNED

a Refit the windscreen washer pump.
a Connect:
- the supply pipes,
- the windscreen washer pump connector.

85A-19
 WIPING - WASHING
Headlight washer pump: Removal - Refitting 85A
HEADLIGHT WASHERS WITH BLADE

REMOVAL a Remove the headlight washer pump - headlight

washer pump connector assembly from the screen
washer reservoir.
I - REMOVAL PREPARATION OPERATION

a Position the vehicle on a two-post lift (see Vehicle: REFITTING

Towing and lifting) (02A, Lifting equipment).
a Partially remove the front wheel arch liner (see I - REFITTING OPERATION FOR PART
Front wheel arch liner: Removal - Refitting) (55A, CONCERNED
Exterior protection).
a Refit the headlight washer pump - headlight washer
pump connector assembly to the screen washer res-
II - OPERATION FOR REMOVAL OF PART ervoir.
CONCERNED
a Clip on the headlight washer pump connector.
a Connect:
- the headlight washer pump connector,
- the headlight washer hose.

cardiagn.com
a Clip on the clip.

II - FINAL OPERATION.
a Fit the front wheel arch liner (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion).

131735

a Unfasten clip (1) .

a Disconnect:
- the headlight washer hose,

- the headlight washer pump connector (2) .

131736

a Unclip:

- the headlight washer pump connector in the direc-

tion (3) ,
- the headlight washer pump in the direction (4) .

85A-20
 WIPING - WASHING
Headlight washer jet: Removal - Refitting 85A
HEADLIGHT WASHERS WITH BLADE

REMOVAL REFITTING

I - REFITTING OPERATION FOR PART

I - REMOVAL PREPARATION OPERATION
CONCERNED
a Position the vehicle on a two-post lift (see Vehicle: a Fit the headlight washer jet to the front bumper.
Towing and lifting) (02A, Lifting equipment).
a Refit:
a Remove the front bumper (see Front bumper: Re- - the headlight washer jet support,
moval - Refitting) (55A, Exterior protection). - the headlight washer jet clip.
a Connect the supply pipe.
II - OPERATION FOR REMOVAL OF PART a Refit the supply pipe mounting clip.
CONCERNED

II - FINAL OPERATION.
a Refit the front bumper (see Front bumper: Remov-
al - Refitting) (55A, Exterior protection).

cardiagn.com
130841

a Remove the clip (1) from the supply pipe.

a Disconnect the supply pipe.

a Unclip the headlight washer jet clip (2) .

a Remove the headlight washer jet support (3) .

130842

a Remove the headlight washer jet (4) from the front

bumper.

85A-21
 WIPING - WASHING
Front screen washer jet: Removal - Refitting 85A
Special tooling required

Car. 1363 Set of trim removal levers.

REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130433
a Unclip the windscreen washer jet (1) using the (Car.
1363).
a Disconnect the pipe from the windscreen washer jet.
a Attach the pipe for the windscreen washer jet using
adhesive tape so that the windscreen washer jet
pipe does not fall into the scuttle panel half-grille.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a Connect the pipe for the windscreen washer jet.
a Clip on the windscreen washer jet.

85A-22
 WIPING - WASHING
Rear screen washer jet: Removal - Refitting 85A
Special tooling required

Car. 1363 Set of trim removal levers.

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the upper tailgate trim (see Tailgate trim:
Removal - Refitting) (73A, Non-side opening ele-
ments trim).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130435
a Remove the rear screen washer jet (3) using the tool
(Car. 1363) (4) .

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
130434 a Refit the rear screen washer jet.
a Disconnect: a Connect the pipe for the rear screen washer jet.
- the rear screen washer jet pipe at (1) , a Refit the clip.
- the clip (2) .
II - FINAL OPERATION.
a Refit the upper tailgate trim (see Tailgate trim: Re-
moval - Refitting) (73A, Non-side opening ele-
ments trim).

85A-23
 WIPING - WASHING
Windscreen washer reservoir: Removal - Refitting 85A
Tightening torquesm

windscreen washer bot- 10 N.m

tle bolts

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Position the vehicle on a two-post lift (see Vehicle:

Towing and lifting) (02A, Lifting equipment).

a Remove the front bumper (see Front bumper: Re-

moval - Refitting) (55A, Exterior protection).

cardiagn.com
II - OPERATION FOR REMOVAL OF PART
CONCERNED 131367

a Remove:

- the front bolts (3) of the windscreen washer bottle,

- the rear bolt (4) of the windscreen washer bottle,

- the windscreen washer bottle,

- the windscreen washer pump from the windscreen
washer bottle.

Note:
Mark the routing of the supply pipes and wiring.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit:
131366
- the windscreen washer pump to the windscreen
a Place a container underneath the windscreen wash- washer bottle,
er bottle. - the windscreen washer bottle,
a Remove the windscreen washer bottle neck (see - the front bolts of the windscreen washer bottle,
85A, Wiping - Washing, Windscreen washer res-
- the rear bolt of the windscreen washer bottle.
ervoir neck: Removal - Refitting, page 85A-26) .
a Torque tighten the windscreen washer bottle
a Disconnect: bolts (10 N.m).

- the connector (1) from the windscreen washer a Connect:

pump,
- the supply pipes,
- the supply pipes (2) . - the windscreen washer pump connector.

85A-24
 WIPING - WASHING
Windscreen washer reservoir: Removal - Refitting 85A
a Refit the windscreen washer bottle neck (see 85A,
Wiping - Washing, Windscreen washer reservoir
neck: Removal - Refitting, page 85A-26) .

II - FINAL OPERATION.
a Refit the front bumper (see Front bumper: Remov-
al - Refitting) (55A, Exterior protection).
a Fill the windscreen washer bottle.

cardiagn.com

85A-25
 WIPING - WASHING
Windscreen washer reservoir neck: Removal - Refitting 85A
REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130843
a Unfasten clip (1) .
a Separate the neck (2) from the windscreen washer
bottle.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a Refit the windscreen washer bottle neck.
a Engage clip.

85A-26
 RADIO
Radio: List and location of components 86A
2.1 - Window mounted radio aerial

I - LIST OF COMPONENTS

No. Description

(1) Radio control satellite

(2.2) Radio aerial

(3) Radio

(4) Radio unit

(5) Display
135217

(6) Tweeter
2.2 - Roof mounted radio aerial
(7) Front central speaker

cardiagn.com
(8) Speaker in the front door

(9) Speaker in the rear door

(10) Subwoofer

(11) Tuner-amplifier

II - LOCATION OF COMPONENTS

1 - Radio control satellite

130728

3 - Radio

130727

130729

86A-1
 RADIO
Radio: List and location of components 86A
4 - Radio unit 7- Front central speaker

cardiagn.com
130730 130733

5 - Display 8 - Speaker in the front door

130731

6 - Tweeter

130734

130747

86A-2
 RADIO
Radio: List and location of components 86A
9 - Speaker in the rear door 11 - Tuner - amplifier

cardiagn.com
130735 130737

10 - Subwoofer

130736

86A-3
 RADIO
Radio: Removal - Refitting 86A
II - OPERATION FOR REMOVAL OF PART
Special tooling required CONCERNED
Ms. 1373 Tool for removing radios or
chronotachographs.

REMOVAL

I - REMOVAL PREPARATION OPERATION

cardiagn.com
132550

130758
a Remove the centre front panel side trim (1) .

132551

a Remove the radio using the tool (Ms. 1373) (2) .

a Disconnect the connectors.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

a Connect the connectors.

a Refit the radio.

86A-4
 RADIO
Radio: Removal - Refitting 86A
II - FINAL OPERATION.
a Refit the centre front panel side trim.

cardiagn.com

86A-5
 RADIO
Receiver: Removal - Refitting 86A
Special tooling required

Ms. 1373 Tool for removing radios or

chronotachographs.

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove:

- the rear centre luggage compartment floor trim

(see Luggage compartment floor lining: Re-
moval - Refitting) (71A, Body internal trim),

- the front centre luggage compartment floor trim

(see Luggage compartment floor lining: Re-
moval - Refitting) (71A, Body internal trim),

cardiagn.com
- the lower trim of the C-pillar (see C-pillar lower
trim: Removal - Refitting) (71A, Body internal 130739
trim),
a Remove:
- the luggage compartment side trim (see Luggage
compartment floor lining: Removal - Refitting) - the nuts (3) ,
(71A, Body internal trim).
- the tuner-amplifier from the support.

II - REMOVAL OPERATION FOR THE PART

CONCERNED 2 - Radio unit

1 - Tuner-amplifier

130740

a Remove the bolts (4) .

130738

a Remove nuts (1) . a Unclip the wiring at (5) .

a Disconnect the connectors (2) . a Disconnect the connectors (6) .

86A-6
 RADIO
Receiver: Removal - Refitting 86A
- the rear centre luggage compartment floor trim
(see Luggage compartment floor lining: Re-
moval - Refitting) (71A, Body internal trim).

130741

a Remove the radio unit using the tool (Ms. 1373).

REFITTING

cardiagn.com
I - REFITTING OPERATION FOR PART
CONCERNED

1 - Tuner-amplifier
a Refit:

- the tuner-amplifier to the support,

- the nuts.

a Connect the connectors.

a Refit the nuts.

2 - Radio unit

a Refit the radio unit to the support.

a Connect the connectors.
a Attach the wiring.

a Refit the bolts.

II - FINAL OPERATION.
a Refit:

- the luggage compartment side trim (see Luggage

compartment floor lining: Removal - Refitting)
(71A, Body internal trim),
- the lower trim of the C-pillar (see C-pillar lower
trim: Removal - Refitting) (71A, Body internal
trim),
- the front centre luggage compartment floor trim
(see Luggage compartment floor lining: Re-
moval - Refitting) (71A, Body internal trim),

86A-7
 RADIO
Radio aerial: Removal - Refitting 86A
REMOVAL a Remove:

- the amplifier mounting clip using a flat-blade screw-

I - REMOVAL PREPARATION OPERATION driver,

- the amplifier (4) .

1 - Radio aerial incorporated in the window glass
a Unfasten the clip (5) .
a Remove:
a Remove the bolt (6) .
- the upper tailgate trim (see Tailgate trim: Remov-
al - Refitting) (73A, Non-side opening elements
trim),
- the lower trim of the C-pillar (see C-pillar lower
trim: Removal - Refitting) (71A, Body internal
trim),
- the upper trim of the C-pillar (see C-pillar upper
trim: Removal - Refitting) (71A, Body internal
trim).

cardiagn.com
2 - Roof radio aerial
a Remove:
- the lower trim of the C-pillar (see C-pillar lower
trim: Removal - Refitting) (71A, Body internal 130743
trim),
a Disconnect the connector (7) .
- the upper trim of the C-pillar (see C-pillar upper
a Unfasten clip (8) .
trim: Removal - Refitting) (71A, Body internal
trim), a Remove the bolt (9) .
- the headlining (see Headlining: Removal - Refit-
ting) (71A, Body internal trim).

II - REMOVAL OPERATION FOR THE PART

CONCERNED

1 - Radio aerial incorporated in the window glass

130744

a Unclip the clips (10) .

a Disconnect the connector (11) .

a Remove the radio aerial wiring.

130742
Note:

a Disconnect the connector (1) . When replacing the printed radio aerial on the
rear screen, replace the rear screen glass (see
a Remove the bolt (2) . Rear screen: Removal - Refitting) (54A, Win-
a Disconnect the connector (3) . dows).

86A-8
 RADIO
Radio aerial: Removal - Refitting 86A
2 - Roof radio aerial - the radio aerial wiring.
a Connect the connectors (11) .
a Attach the clips (10) .
a Refit the bolt (9) .
a Clip on the clip (8) .
a Connect the connector (7) .
a Refit the bolt (6) .
a Engage clip (5) .
a Refit the amplifier (4) .
a Clip on the amplifier mounting clip.
a Connect the connector (3) .
130745
a Refit the bolt (2) .
a Disconnect the connector (12) .
a Connect the connector (1) .
a Unclip the clips (13) .

cardiagn.com
2 - Roof radio aerial
a Refit:
- the radio aerial,
- the radio aerial nut.
a Attach the clips (13) .
a Connect the connector (12) .

II - FINAL OPERATION.

1 - Radio aerial incorporated in the window glass

a Refit:
- the upper trim of the C-pillar (see C-pillar upper
trim: Removal - Refitting) (71A, Body internal
trim),
- the lower trim of the C-pillar (see C-pillar lower
trim: Removal - Refitting) (71A, Body internal
130746
trim),
a Remove:
- the upper tailgate trim (see Tailgate trim: Remov-
- the nut (14) , al - Refitting) (73A, Non-side opening elements
trim).
- the radio aerial.

2 - Roof radio aerial

REFITTING
a Refit:

I - REFITTING OPERATION FOR PART - the headlining (see Headlining: Removal - Refit-
CONCERNED ting) (71A, Body internal trim),
- the upper trim of the C-pillar (see C-pillar upper
trim: Removal - Refitting) (71A, Body internal
1 - Radio aerial incorporated in the window glass
trim),
a Refit:
- the rear pillar lower trim (see C-pillar lower trim:
- the radio aerial, Removal - Refitting) (71A, Body internal trim).

86A-9
 RADIO
Tweeter: Removal - Refitting 86A
REMOVAL - the tweeter bolts.

I - REMOVAL PREPARATION OPERATION II - FINAL OPERATION.

a Refit the tweeter grille.

130747

cardiagn.com
a Unclip the tweeter grille (1) using a flat-blade screw-
driver.

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130748
a Remove:
- the bolts (2) ,
- the tweeter (3) .
a Disconnect the tweeter speaker connector.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Connect the tweeter speaker connector.
a Refit:
- the tweeter,

86A-10
 RADIO
Front speakers: Removal - Refitting 86A
REMOVAL

I - REMOVAL PREPARATION OPERATION

1 - Front door speaker

130751

a Remove:

- the front centre speaker cover bolts (3) ,

cardiagn.com
- the front centre speaker cover.

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130749
1 - Front door speaker
a Remove the front side door trim (1) (see Front side
door trim: Removal - Refitting) (72A, Side opening
elements trim).

2 - Front centre speaker

130750
a Remove the front centre speaker trim (2) . 130752

a Remove:

- the bolts (4) ,

- the front speaker (5) .

a Disconnect the connector.

86A-11
 RADIO
Front speakers: Removal - Refitting 86A
2 - Front centre speaker 2 - Front centre speaker
a Refit:
- the front centre speaker cover,
- the front centre speaker cover bolts,
- the front centre speaker trim.

130753

a Remove:

cardiagn.com
- the bolts (6) ,

- the front centre speaker (7) .

a Disconnect the connector.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

1 - Front door speaker

a Connect the front door speaker connector.

a Refit:

- the front door speaker,

- the front door speaker bolts.

2 - Front centre speaker

a Connect the front centre speaker connector.

a Refit:

- the front centre speaker,

- the front centre speaker bolts.

II - FINAL OPERATION.

1 - Front door speaker

a Refit the front side door trim (see Front side door
trim: Removal - Refitting) (72A, Side opening ele-
ments trim).

86A-12
 RADIO
Rear speakers: Removal - Refitting 86A
REMOVAL a Disconnect the rear speaker connector.

I - REMOVAL PREPARATION OPERATION REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Connect the rear speaker connector.
a Refit:
- the rear speaker (3) ,
- the rear speaker bolts (2) .

II - FINAL OPERATION
a Refit the rear side door trim (see Rear side door
trim: Removal - Refitting) (72A, Side opening ele-
ment trim).

cardiagn.com
130754
a Remove the rear side door trim (1) (see Rear side
door trim: Removal - Refitting) (72A, Side opening
element trim).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130756
a Remove:
- the bolts (2) ,
- the rear speaker (3) .

86A-13
 RADIO
CD changer: Removal - Refitting 86A
II - OPERATION FOR REMOVAL OF PART
Special tooling required CONCERNED
Ms. 1820 Tool for removing Clarion and
VDO radios

REMOVAL

I - REMOVAL PREPARATION OPERATION

130759

cardiagn.com
130758
a Remove the centre front panel side trim (1) .

130760
a Remove the radio using the tool (Ms. 1820) (2) .
a Disconnect the connectors.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Connect the connectors.
a Refit the radio.

II - FINAL OPERATION
a Refit the centre front panel side trim.

86A-14
 RADIO
Display: Removal - Refitting 86A
REMOVAL II - OPERATION FOR REMOVAL OF PART
CONCERNED

I - REMOVAL PREPARATION OPERATION

130763

130761
a Unclip the « display - display protector » assembly.

cardiagn.com
a Remove the front centre speaker trim (1) . a Disconnect the display connector.

130762 130764

a Remove: a Remove the upper bolts (3) .

- the front centre speaker cover bolts (2) ,

- the front centre speaker cover.

86A-15
 RADIO
Display: Removal - Refitting 86A

cardiagn.com
130765
a Remove:
- the lower bolts (4) ,
- the display (5) from the display protector.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Refit:
- the display on the display protector,
- the lower bolts,
- the upper bolts.
a Connect the connector.
a Clip on the « display - display protector » assembly.

II - FINAL OPERATION.
a Refit:
- the front centre speaker cover,
- the front centre speaker cover bolts,
- the front centre speaker trim.

86A-16
 RADIO
Radio control satellite: Removal - Refitting 86A
REMOVAL

I - REMOVAL PREPARATION OPERATION

IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.

IMPORTANT
To prevent the pyrotechnic components from
130767
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min a Disconnect the connector (3) .
after disconnecting the battery.
REFITTING

cardiagn.com
a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-3) .
I - REFITTING OPERATION FOR PART
a Remove: CONCERNED

- the driver's front airbag (see 88C, Air bag and Pre- a Connect the connector.
tensioners, Driver's frontal airbag: Removal - a Refit:
Refitting, page 88C-10) ,
- the radio control satellite,
- the steering wheel (see Steering wheel: Removal - the bolts.
- Refitting) (36A, Steering assembly),

- the half cowlings (see Steering column: Removal II - FINAL OPERATION.

- Refitting) (36A, Steering assembly).
a Refit:
- the half cowlings (see Steering column: Removal
II - OPERATION FOR REMOVAL OF PART - Refitting) (36A, Steering assembly),
CONCERNED
- the steering wheel (see Steering wheel: Removal
- Refitting) (36A, Steering assembly),
- the driver's front airbag (see 88C, Air bag and Pre-
tensioners, Driver's frontal airbag: Removal -
Refitting, page 88C-10) .
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

130766

a Remove:

- the bolts (1) ,

- the radio control satellite (2) .

86A-17
 RADIO
Subwoofer: Removal - Refitting 86A
REMOVAL REFITTING

I - REMOVAL PREPARATION OPERATION I - REFITTING OPERATION FOR PART

CONCERNED
a Remove the rear central luggage compartment floor
a Refit the subwoofer.
(see Luggage compartment floor lining: Remov-
al - Refitting) (71A, Body internal trim). a Connect the connector.
a Clip on the wiring clip.
a Refit the mounting bracket.

II - FINAL OPERATION.
a

Note:
The emergency spare wheel and the subwoofer
must be mounted correctly.

cardiagn.com
a Refit:
- the front luggage compartment floor casing,
- the rear central luggage compartment floor (see
Luggage compartment floor lining: Removal -
Refitting) (71A, Body internal trim).

130755

a Remove the front luggage compartment floor casing

(1) .

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130757

a Remove the mounting bracket (2) .

a Unclip the wiring clip (3) .

a Disconnect the connector (4) .

a Remove the subwoofer.

86A-18
 PASSENGER COMPARTMENT CONNECTION UNIT
UCH: Removal - Refitting 87B
Equipment required

Diagnostic tool

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-3) .

cardiagn.com
131585
a Remove:
- the bolts (3) ,
- the tyre pressure monitor computer (4) ,
- the additional cornering lights computer (5) .

131584
a Remove:
- the bolts (1) ,
- the lower cover (2) .

131586
a Remove the bolts (6) .
a Move aside the passenger compartment fuse and
relay box (7) .

87B-1
 PASSENGER COMPARTMENT CONNECTION UNIT
UCH: Removal - Refitting 87B

131589

a Disconnect the connectors.

cardiagn.com
131587
a Remove the bolt (8) .
a Disconnect the connectors (9) .
a Remove the relays (10) .

II - REMOVAL OF PART CONCERNED

131590

a Remove the UCH.

REFITTING

I - REFITTING PART CONCERNED

a Refit the UCH.
a Connect the connectors.
131588
a Refit the bolts (11) .
a Remove the bolts (11) .

II - FINAL OPERATION.

a Refit the relays.

a Connect the connectors.
a Refit the bolts (8) .

87B-2
 PASSENGER COMPARTMENT CONNECTION UNIT
UCH: Removal - Refitting 87B
a Fit the passenger compartment fuse and relay box in
its original position.
a Refit:
- the bolts (6) ,
- the additional cornering lights computer,
- the tyre pressure monitor computer,
- the bolts (3) ,
- the lower cover (2) ,
- the bolts (1) .
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .
a When replacing the UCH, carry out the necessary
operations using the Diagnostic tool (see Fault
finding - Replacement of components) (87B, Pas-
senger compartment connection unit).

cardiagn.com

87B-3
 OPENING ELEMENT MANAGEMENT
Opening elements management: List and location of components 87C
I - LIST OF COMPONENTS 2 - Passenger compartment fuse and relay box

No. Description

(1) UCH

(2) Passenger compartment fuse and

relay box

(3) Remote door locking control

(4) Central locking switch

(5) Tailgate opening switch

(6) Tailgate locking switch

(7) Opening aerials

cardiagn.com
II - POSITION OF THE COMPONENTS
132491
1 - UCH
3 - Door locking remote control

132490
The UCH is located in the dashboard, behind the pas- 132492
senger compartment relay unit; to remove it (see 87B,
Passenger compartment connection unit, UCH: Re- 4 - Door locking switch
moval - Refitting, page 87B-1) .

132493

87C-1
 OPENING ELEMENT MANAGEMENT
Opening elements management: List and location of components 87C
5 - Tailgate opening switch

132494 132497
Opening aerial in the rear absorber: it is not necessary
6 - Tailgate locking switch to remove the rear bumper.

cardiagn.com
132495

7 - Opening aerials

132498
Keyless entry computer: to access the keyless entry
computer, the glove box must be removed.

132496
Opening aerials in the front door handles.

87C-2
 OPENING ELEMENT MANAGEMENT
Opening aerial: Removal - Refitting 87C
REMOVAL

I - REMOVAL PREPARATION OPERATION

1 - Opening aerial on the driver and passenger

sides
a Remove the door handle on the side concerned (see
Exterior door handle: Removal - Refitting) .

2 - Rear opening aerial

a Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
130769
3 - Keyless entry computer a Remove the opening aerial (3) from the door handle.
a Remove the glovebox (see Glovebox: Removal -
Refitting) 2 - Rear opening aerial

cardiagn.com
II - REMOVAL OF PART CONCERNED

1 - Opening aerial on the driver and passenger

sides

130770
a

Note:
It is not necessary to remove the rear bumper.
130768
a Remove:
a Remove:
- the clips (4) ,
- the bolt (1) ,
- the opening aerial (5) .
- the cover (2) .
a Disconnect the connector (6) .

87C-3
 OPENING ELEMENT MANAGEMENT
Opening aerial: Removal - Refitting 87C
3 - Keyless entry computer - the keyless entry computer bolt.

II - FINAL OPERATION

1 - Opening aerial on the driver and passenger

sides
a Refit the door handle (see Exterior door handle:
Removal - Refitting) .

2 - Keyless entry computer

a Refit the glovebox (see Glovebox: Removal - Refit-
ting) .

cardiagn.com
132498
a Remove the keyless entry computer bolt (7) .
a Disconnect the keyless entry computer connector
(8) .
a Remove the keyless entry computer.

REFITTING

I - REFITTING PART CONCERNED

1 - Opening aerial on the driver and passenger

sides
a Refit the opening aerial on the door handle.
a Refit:
- the cover,
- the bolt.

2 - Rear opening aerial

a Connect the connector.
a Refit:
- the opening aerial,
- the clips.

3 - Keyless entry computer

a Connect the keyless entry computer connector.
a Refit:
- the keyless entry computer,

87C-4
 OPENING ELEMENT MANAGEMENT
Tailgate opening switch: Removal - Refitting 87C
II - OPERATION FOR REMOVAL OF PART
CONCERNED

130845
a Disconnect the tailgate opening switch connector (2)

cardiagn.com
.
130844

Note:
In case of an electrical fault, it is possible to open
the tailgate manually.
Carry out this operation from inside the vehicle.
Unlock the tailgate by turning the fastener (1) in the
direction of the arrow.

REMOVAL

I - REMOVAL PREPARATION OPERATION 130846

a
a Remove the tailgate lower trim (see Tailgate trim:
Removal - Refitting) (73A, Non-side opening ele- Note:
ments trim).
Carefully unclip the tailgate opening switch cover
to avoid damaging it.

a Separate the cover (3) from the tailgate opening

switch.
a Remove the tailgate opening switch assembly.

87C-5
 OPENING ELEMENT MANAGEMENT
Tailgate opening switch: Removal - Refitting 87C

130847
a Unclip the tailgate opening switch (4) by pressing on
the clips in the direction of the arrows.
a Remove the tailgate opening switch from its support.

cardiagn.com
REFITTING

I - REFITTING PREPARATION OPERATION

a Check the condition of the tailgate opening switch
cover.
a Replace the cover if it is damaged.

II - REFITTING OPERATION FOR PART

CONCERNED
a Refit:
- the tailgate opening switch on the cover,
- the tailgate opening switch assembly on the tail-
gate.
a Connect the tailgate opening switch connector.

III - FINAL OPERATION.

a Refit the tailgate lower trim (see Tailgate trim: Re-
moval - Refitting) (73A, Non-side opening ele-
ments trim).

87C-6
 OPENING ELEMENT MANAGEMENT
Tailgate locking switch: Removal - Refitting 87C
REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove:

- the tailgate lower trim (see Tailgate trim: Removal

- Refitting) (73A, Non-side opening elements trim),

- the tailgate lock (see Tailgate lock: Removal - Re-

fitting) (52A, Non-side opening element mecha-
nisms),

- the rear screen wiper arm (see 85A, Wiping -

Washing, Rear screen wiper arm: Removal - Re-
fitting, page 85A-13) . 131371

a Remove:
II - REMOVAL OF PART CONCERNED
- the bolts (4) from the tailgate locking switch sup-
port,

cardiagn.com
- the tailgate locking switch (5) from the support.

REFITTING

I - REFITTING PREPARATION OPERATION

a Check the condition of the clips on the tailgate trim.

a Replace the clips if they are damaged.

II - REFITTING PART CONCERNED

131369 a Refit:

- the tailgate locking switch on the tailgate trim with

the support,

- the bolts of the tailgate locking switch support,

- the tailgate trim on the tailgate,

- the tailgate trim nuts.

a Connect the tailgate locking switch connector.

III - FINAL OPERATION.

a Refit:

- the rear screen wiper arm (see 85A, Wiping -

131370
Washing, Rear screen wiper arm: Removal - Re-
a Remove the nuts (2) from the tailgate trim (1) . fitting, page 85A-13) ,

a Disconnect the connector (3) from the tailgate lock- - the tailgate lock (see Tailgate lock: Removal - Re-
ing switch. fitting) (52A, Non-side opening element mecha-
nisms),
a Unclip the tailgate trim.
- the tailgate lower trim (see Tailgate trim: Removal
a Remove the tailgate trim. - Refitting) (73A, Non-side opening elements trim).

87C-7
 ELECTRIC WINDOWS - SUNROOF
Electric window: List and location of components 87D
I - LIST OF COMPONENTS 3 - Front electric window switch on the passenger
door

No. Description

(1) UCH

(2) Front electric window switch on the

driver's door

(3) Front electric window switch on the pas-

senger door

(4) Rear window winder switch

II - LOCATION OF COMPONENTS

130850
1 - UCH

cardiagn.com
4 - Rear window winder switch

130848
The UCH is located in the dashboard, behind the pas- 130851
senger compartment relay unit. To remove it (see 87B,
Passenger compartment connection unit, UCH: Re-
moval - Refitting, page 87B-1) .

2 - Front electric window switch on the driver's

door

130849

87D-1
 ELECTRIC WINDOWS - SUNROOF
Electric sunroof: List and location of components 87D
ELECTRICAL SUNROOF + FIXED REAR SECTION
I - LIST OF COMPONENTS 2 - Passenger compartment fuse and relay box

No. Description

(1) UCH

(2) Passenger compartment fuse and relay

box

(3) Sunroof switch

(4) Sunroof motor - computer

II - LOCATION OF COMPONENTS

1 - UCH

cardiagn.com
130853

3 - Sunroof switch

130852
The UCH is located in the dashboard, behind the pas-
senger compartment relay unit. To remove it (see 87B,
Passenger compartment connection unit, UCH: Re-
moval - Refitting, page 87B-1) .

130460

87D-2
 ELECTRIC WINDOWS - SUNROOF
Electric sunroof: List and location of components 87D
ELECTRICAL SUNROOF + FIXED REAR SECTION
4 - Sunroof motor - computer

130855
The « sunroof motor - computer » assembly is located
under the headlining, at the rear of the vehicle.

cardiagn.com
The sunroof opening motor and the electric sunroof
computer cannot be separated.

87D-3
 ELECTRIC WINDOWS - SUNROOF
Front electric window switches on driver's door: Removal - Refitting 87D
a Refit the electric window switch plate by inserting it
Special tooling required from the rear.
Car. 1363 Set of trim removal levers.

REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130856

a Unclip the electric window switch plate using the tool

(Car. 1363).

130857

a Disconnect the electric window switch connector (1)

.
a Unclip clips (2) .
a Remove the electric window switch from the plate.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a Refit the electric window switch on the plate.
a Connect the window winder switch connector.

87D-4
 ELECTRIC WINDOWS - SUNROOF
Front electric window switch on passenger door: Removal - Refitting 87D
a Refit the electric window switch plate by inserting it
Special tooling required from the rear.
Car. 1363 Set of trim removal levers.

REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130858

a Unclip the electric window switch plate using the tool

(Car. 1363).

130859

a Disconnect the electric window switch connector (1)

.
a Unclip the two clips (2) .
a Remove the electric window switch from the plate.

REFITTING

REFITTING OPERATION FOR PART CONCERNED

a Refit the electric window switch on the plate.
a Connect the window winder switch connector.

87D-5
 ELECTRIC WINDOWS - SUNROOF
Rear electric window switch: Removal - Refitting 87D
Special tooling required
REFITTING

Car. 1363 Set of trim removal levers. REFITTING OPERATION FOR PART CONCERNED
a Refit the rear electric window switch on the plate.
REMOVAL a Connect the rear electric window switch connector.
a Refit:
OPERATION FOR REMOVAL OF PART - the rear electric window plate by inserting it from
CONCERNED the rear,
- the bolt,
- the cover.

cardiagn.com
130860

a Remove:

- the cover,

- bolt (1) .

130861

a Unclip the rear electric window switch plate using

the tool (Car. 1363).

a Disconnect the rear electric window switch connec-

tor (2) .

a Unclip the two clips (3) .

a Separate the rear electric window switch from the

plate.

87D-6
 ELECTRIC WINDOWS - SUNROOF
Sunroof switch: Removal - Refitting 87D
ELECTRICAL SUNROOF + FIXED REAR SECTION

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the interior light (see 81B, Interior light-
ing, Interior light: Removal - Refitting, page 81B-
4) .

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130864
a Remove:
- the sunroof switch bolts (3) ,

cardiagn.com
- the sunroof switch (4) .

REFITTING

I - REFITTING OPERATION FOR PART

130862 CONCERNED
a Unclip the translucent covers (1) . a Refit:
- the sunroof switch,
- the sunroof switch bolts,
- the sunroof switch cover,
- the translucent covers.

II - FINAL OPERATION.
a Refit the interior light (see 81B, Interior lighting, In-
terior light: Removal - Refitting, page 81B-4) .

130863
a Unclip the sunroof switch cover (2) .

87D-7
 ELECTRIC WINDOWS - SUNROOF
Sunroof opening motor: Removal - Refitting 87D
ELECTRICAL SUNROOF + FIXED REAR SECTION
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm

sunroof motor bolts 3 N.m

130866
a Disconnect the connector (2) from the sunroof mo-

cardiagn.com
tor.
130865
a Remove:
- the bolts (3) from the sunroof motor,
Note:
- the sunroof motor.
In the event of a fault, the electric sunroof motor
can be moved manually at (1) using an Allen key.
REFITTING

Note: I - REFITTING OPERATION FOR PART

CONCERNED
The sunroof motor and the electric sunroof com-
puter cannot be separated. a Refit:
- the sunroof motor,
REMOVAL - the sunroof motor bolts.
a Torque tighten the sunroof motor bolts (3 N.m).
I - REMOVAL PREPARATION OPERATION a Connect the sunroof motor connector.
a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-3) . II - FINAL OPERATION.
a Remove the headlining (see Headlining: Removal - a Refit the headlining (see Headlining: Removal -
Refitting) (71A, Body internal trim). Refitting) (71A, Body internal trim).
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

87D-8
 PARKING DISTANCE CONTROL
Parking distance control: List and location of components 87F
FRONT AND REAR PROXIMITY RADAR
I - LIST OF COMPONENTS 2 - Front parking distance control buzzers

No. Description

(1) Parking distance control switch

(2) Front parking distance control

buzzer

(3) Rear parking distance control

buzzer

(4) Front proximity sensors

(5) Rear proximity sensors

(6) Parking distance control computer 131374

The front parking distance control buzzer (2) is located
at the rear of the dashboard lower cover on the driver's

cardiagn.com
II - LOCATION OF COMPONENTS
side.

1 - Parking distance control switch

3 - Rear parking distance control buzzer

131373
131375
The rear parking distance control buzzer (3) is located
in the left-hand side of the C-pillar lower trim.

87F-1
 PARKING DISTANCE CONTROL
Parking distance control: List and location of components 87F
FRONT AND REAR PROXIMITY RADAR
4 - Front proximity sensors 6 - Parking distance control computer

131378

cardiagn.com
131376
Four proximity radars (4) are clipped into the supports
on the front bumper.

5 - Rear proximity sensors

131377
Four proximity radars (5) are clipped into the supports
on the rear bumper.

87F-2
 PARKING DISTANCE CONTROL
Parking distance control switch: Removal - Refitting 87F
FRONT AND REAR PROXIMITY RADAR

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the dashboard lower cover on the driver's
side (see Dashboard: Removal - Refitting) (57A,
Interior equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130867
a Unclip the parking distance control switch (1) from
the dashboard lower cover.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Clip the parking distance control switch onto the
dashboard lower cover.

II - FINAL OPERATION.
a Refit the dashboard lower cover on the driver's side
(see Dashboard: Removal - Refitting) (57A, Interi-
or equipment).

87F-3
 PARKING DISTANCE CONTROL
Parking distance control buzzer: Removal - Refitting 87F
FRONT AND REAR PROXIMITY RADAR

REMOVAL

OPERATION FOR REMOVAL OF PART

CONCERNED

1 - Front parking distance control buzzer

a Remove the dashboard lower cover on the driver's
side (see Dashboard: Removal - Refitting) (57A,
Interior equipment).

cardiagn.com
130869
a Disconnect the connector (3) from the rear parking
distance control buzzer.
a Remove:
130868
- the rear parking distance control buzzer bolt (4) ,
a Remove:
- the rear parking distance control buzzer.
- the front parking distance control buzzer bolts (1) ,
- the front parking distance control buzzer (2) .
REFITTING
2 - Rear parking distance control buzzer
REFITTING OPERATION FOR PART CONCERNED
a Remove the C-pillar lower trim on the left-hand side
(see C-pillar lower trim: Removal - Refitting)
(71A, Body internal trim). 1 - Front parking distance control buzzer
a Refit:
- the front parking distance control buzzer,
- the front parking distance control buzzer bolts,
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment).

2 - Rear parking distance control buzzer

a Refit:
- the rear parking distance control buzzer,
- the rear parking distance control buzzer bolts.
a Connect the rear parking distance control buzzer
connector.
a Refit the C-pillar lower trim on the left-hand side (see
C-pillar lower trim: Removal - Refitting) (71A,
Body internal trim).

87F-4
 PARKING DISTANCE CONTROL
Proximity radar: Removal - Refitting 87F
FRONT AND REAR PROXIMITY RADAR

REMOVAL Front bumper

I - REMOVAL PREPARATION OPERATION

a

Note:
The operations for removing and refitting the
front and rear proximity radars are identical.

a Remove the front bumper (see Front bumper: Re-

moval - Refitting) (55A, Exterior protection) or the
rear bumper (see Rear bumper: Removal - Refit-
ting) (55A, Exterior protection).

II - OPERATION FOR REMOVAL OF PART

CONCERNED
a

cardiagn.com
WARNING
The distance control radars are fragile. Handle 131376
with care as the external part cannot withstand
impacts. Rear bumper

131377
a Disconnect the connectors (1) from the proximity ra-
dar.

87F-5
 PARKING DISTANCE CONTROL
Proximity radar: Removal - Refitting 87F
FRONT AND REAR PROXIMITY RADAR

131381
a Unclip the proximity radar at (2) .
a Remove the proximity radar (3) .

cardiagn.com
REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Clip the proximity radar onto its support.
a Connect the proximity radar connectors.

II - FINAL OPERATION.
a Refit the front bumper (see Front bumper: Remov-
al - Refitting) (55A, Exterior protection) or the rear
bumper (see Rear bumper: Removal - Refitting)
(55A, Exterior protection).

87F-6
 PARKING DISTANCE CONTROL
Parking distance control computer: Removal - Refitting 87F
FRONT AND REAR PROXIMITY RADAR
II - FINAL OPERATION.
Equipment required a Refit the luggage compartment floor trim (see Lug-
gage compartment floor lining: Removal - Refit-
Diagnostic tool ting) (71A, Body internal trim).
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .
REMOVAL
a In the event of replacement, carry out the necessary
operations using the Diagnostic tool (see Replace-
I - REMOVAL PREPARATION OPERATION ment of components) (87F, Parking distance con-
a Disconnect the battery (see 80A, Battery, Battery: trol).
Removal - Refitting, page 80A-3) .

a Remove the luggage compartment floor trim (see

Luggage compartment floor lining: Removal -
Refitting) (71A, Body internal trim).

II - OPERATION FOR REMOVAL OF PART

cardiagn.com
CONCERNED

131378

a Disconnect the connectors (1) from the parking dis-

tance control computer.

a Remove:

- the parking distance control computer nuts (2) ,

- the parking distance control computer.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

a Refit:

- the parking distance control computer,

- the parking distance control computer nuts.

a Connect the parking distance control computer con-

nectors.

87F-7
 ENGINE COMPARTMENT CONNECTION UNIT
Protection and Switching Unit: Removal - Refitting 87G
REMOVAL
M9R
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-3) .

2TR

cardiagn.com
130772

a Unclip the clips (3) .

a Remove the air inlet duct (4) .

130771
a Unclip the clips (1) .
a Remove the air inlet duct (2) . II - OPERATION FOR REMOVAL OF PART
CONCERNED

130773

a Unclip the Protection and Switching Unit at (5) .

87G-1
 ENGINE COMPARTMENT CONNECTION UNIT
Protection and Switching Unit: Removal - Refitting 87G

cardiagn.com
130774
a Disconnect the connectors (6) from the Protection
and Switching Unit by pressing on the tab of the con-
nector.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Fit the protection and switching unit.
a Connect the connectors.
a Check the condition of the wiring.
a Clip on the Protection and Switching Unit.

II - FINAL OPERATION.
a Refit the air inlet duct.
a Clip on the clips.
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .
a When replacing the Protection and Switching Unit,
carry out the necessary configuration (see Replace-
ment of components) (87G, Engine compartment
connection unit).

87G-2
 WIRING HARNESS
Computers: List and location of components 88A
No. Description

I - LIST OF COMPONENTS (9) Pre-postheating unit

(10) Radio
No. Description
(11) Yaw speed and lateral acceleration
(1) Additional cornering lights computer sensor

(2) Tyre pressure monitor computer (12) ABS / ESP computer

(3) Passenger compartment fuse and (13) Navigation computer

relay box
(14) Rear final drive coupler computer
(4) UCH
(15) Telephone computer
(5) Protection and switching unit
(16) Airbag computer
(6) Engine fuse and relay box
(17) Radio unit

cardiagn.com
(7) Injection computer

(8) Automatic gearbox computer II - LOCATION OF COMPONENTS

130775

88A-1
 WIRING HARNESS
Computers: List and location of components 88A
Computers integrated into components

130776
The sunroof computer is integrated into the electric
motor (18) .

cardiagn.com
130777
The anti-pinch function is integrated into the electric
motor (19) .

88A-2
 WIRING HARNESS
Diagnostic socket: List and location of components 88A
I - LIST OF COMPONENTS

No. Description

(1) Diagnostic socket

II - LOCATION OF COMPONENTS

1 - Diagnostic socket

cardiagn.com
130778
The diagnostic socket is located on the lower section of
the dashboard lower cover on the driver's side.

88A-3
 AIR BAG AND PRETENSIONERS
Airbag and pretensioners: List and location of components 88C
I - LIST OF COMPONENTS II - LOCATION OF COMPONENTS

1 - Airbag computer
No. Description

(1) Airbag computer

(2) Driver's front airbag

(3) Passenger front airbag

(4) Front (thorax) side airbag

(5) Curtain side airbag

(6) Front seat lap belt pretensioner

(7) Front seat belt buckle

(8) Rear seat belt buckles

cardiagn.com
(9) Front side seat belt

(10) Rear side seat belt

(11) Rear centre seat belt 131742

(12) Side impact sensor

2 - Driver's front airbag
(13) Front impact sensor

(14) Inhibitor switch

(15) Front passenger airbag inhibitor switch

warning light

(16) Passenger seat belt warning light

(17) Passenger presence sensor

131743

88C-1
 AIR BAG AND PRETENSIONERS
Airbag and pretensioners: List and location of components 88C
3 - Passenger front airbag 4 - Front (chest-level) side airbag

131744 131745

5 - Curtain side airbag

cardiagn.com
131746

88C-2
 AIR BAG AND PRETENSIONERS
Airbag and pretensioners: List and location of components 88C
6 - Front seat lap belt pretensioner 9 - Front side seat belt

131747 131750
The front seat lap belt pretensioner cannot be separat-
ed from the front side seat belt. 10 - Rear side seat belt

cardiagn.com
7 - Front seat belt buckle

131751

131748 11 - Rear centre seat belt

8 - Rear seat belt buckles

131752

131749

88C-3
 AIR BAG AND PRETENSIONERS
Airbag and pretensioners: List and location of components 88C
12 - Side impact sensor 14 - Inhibitor switch

cardiagn.com
131753 131755

13 - Front impact sensor 15 - Passenger front airbag inhibitor switch

warning light

131754
131757

88C-4
 AIR BAG AND PRETENSIONERS
Airbag and pretensioners: List and location of components 88C
16 - Passenger seat belt warning light

cardiagn.com
131756

17 - Passenger presence sensor

131758
To remove it (see Passenger presence sensor cov-
er: Removal - Refitting) (59A, Safety equipment).

88C-5
 AIR BAG AND PRETENSIONERS
Airbag and pretensioners: Precautions for the repair 88C
Equipment required
IMPORTANT
Diagnostic tool To eliminate the risk of any accident, do not reuse
pyrotechnic components.
It is essential to destroy pretensioners or airbags
PRECAUTIONS FOR REPAIR
before scrapping a vehicle or a part only.
(see 88C, Air bag and Pretensioners, Airbags
IMPORTANT and pretensioners: Recycling - Destruction,
All operations on airbag and pretensioner systems page 88C-7) .
must be carried out by qualified trained personnel.
The airbags have a pyrotechnic gas generator, with
an ignition module and bag which must not be sep- IMPORTANT
arated. In the event of a repair operation after an impact,
The pretensioners have a pyrotechnic gas genera- the mounting bolts of the seat belts and seat belt
tor and an igniter which must, under no circum- buckles must always be replaced.
stances, be separated.
A visual inspection must be carried out on the pyro-

cardiagn.com
technic system mountings and the tightening torque
must be checked.
IMPORTANT The pyrotechnic systems (pretensioners and airbags)
Never handle the pyrotechnic systems (pretension- must be checked using the Diagnostic tool :
ers or airbags) near to a source of heat or naked
flame - they may be triggered. - after an accident that did not trigger the systems,
- after theft or attempted theft of the vehicle,
- before selling a used vehicle.
IMPORTANT
To prevent the pyrotechnic components from being
permanently deactivated or triggered (airbags or
pretensioners), wait for at least 3 min after discon-
necting the battery.

When an airbag or a pretensioner is triggered, the air-

bag computer is permanently locked and the « airbag
fault » warning light on the instrument panel comes on.
The airbag computer must be replaced (certain compo-
nents lose their nominal specifications after being sub-
jected to the trigger energy)

IMPORTANT

In order to prevent interference with the deployment

of the airbags:
- do not fit a cover to the front seats,
- do not place objects in the area of deployment.

88C-6
 AIR BAG AND PRETENSIONERS
Airbags and pretensioners: Recycling - Destruction 88C
Special tooling required

Ele. 1287 Tool for destroying airbags

and pretensioners.

Ele. 1287-02 Kit of 2 adapters for the air-

bag and pretensioner
destruction tool.

IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-6) .

cardiagn.com
IMPORTANT
To eliminate the risk of any accident, do not reuse 131739
pyrotechnic components. a It is essential to use the tool (Ele. 1287) and (Ele.
It is essential to destroy pretensioners or airbags 1287-02).
before scrapping a vehicle or a part only.
a Use a wiring connector kit 82 00 518 971.

a Attach the wiring connectors 82 00 518 971 to the

adapters (Ele. 1287-02) to obtain an adapter for
WARNING
each colour (green, orange, blue, etc.) (see Wiring:
- Each part is intended for a specific vehicle type Repair) (Technical Note 6015A, 88A, Wiring).
and should not be fitted on another vehicle under
any circumstances. The parts are not interchange- a Use a battery to power the destruction tool.
able.
- Do not trigger pretensioners which are to be I - AIRBAGS
returned under warranty because of a faulty stalk.
This makes analysis of the part by the supplier a
impossible. Return the defective part to Techline in
the packaging of the new part. Note:
The airbags must be destroyed outside the work-
shop, in an area with sufficient space.
WARNING The airbags to be destroyed must be removed.
The destruction procedure cannot be carried out if
local regulations require a special procedure which
has been confirmed and published by the Fault find- Note:
ing, Repair and Procedures Department.
If the airbag has two levels of activation (i.e. it is
fitted with two connectors), destroy both connec-
tors.
Note:
a Prepare the adapter corresponding to the airbag to
If triggering is not possible (faulty ignition module)
be destroyed.
return the part to Techline.
a Connect:

- the adapter to the destruction tool (Ele. 1287),

- the adapter to the airbag.

88C-7
 AIR BAG AND PRETENSIONERS
Airbags and pretensioners: Recycling - Destruction 88C
a Connect the two feed wires of the destruction tool
(Ele. 1287) to a battery.

IMPORTANT
To prevent any risk of an accident when destroy-
ing a pyrotechnic component, check that no-one
is in the vicinity.

a Destroy the airbag by pressing the two push buttons

on the tool simultaneously.

II - PYROTECHNIC PRETENSIONERS AND INERTIA

REELS

1 - Destruction of part fitted on the vehicle to be

scrapped:
a Move the vehicle outside the workshop.

cardiagn.com
a Mark the adapter corresponding to the pyrotechnic
131740 component to be destroyed.
a Put the airbag on two wooden blocks. a Connect:
- the destruction tool (Ele. 1287) to the adapter,
- the adapter to the pyrotechnic component.
a Unwind the tool wiring fully, so that you are far
enough away from the vehicle (approximately ten
metres) when the device is triggered.
a Connect the two feed wires of the destruction tool
(Ele. 1287) to a battery.

IMPORTANT
To prevent any risk of an accident when destroy-
ing a pyrotechnic component, check that no-one
is in the vicinity.

a Destroy the pyrotechnic component by pressing the

two push buttons on the tool simultaneously.

2 - Destruction of part removed from the vehicle:

131741 a Proceed in the same way as for an airbag (in a stack
of old tyres).
a The destruction procedure is carried out in a stack of
old tyres.
a Make sure that the airbag deployment will not be
hindered.
a Unwind the full length of the wiring for the tool, in or-
der to distance it as far away as possible from the
pyrotechnic component to be destroyed.

88C-8
 AIR BAG AND PRETENSIONERS
Airbag computer: Removal - Refitting 88C
REFITTING
Tightening torquesm
I - REFITTING OPERATION FOR PART
airbag computer bolt (3) 7 N.m CONCERNED

airbag computer bolts 25 N.m a Refit:

(2) - the airbag computer,
- the airbag computer bolt,
IMPORTANT - the bolts from the airbag computer.
To prevent the pyrotechnic components from being a Torque tighten:
permanently deactivated or triggered (airbags or
pretensioners), wait for at least 3 min after discon- - the airbag computer bolt (3) (7 N.m),
necting the battery. - the airbag computer bolts (2) (25 N.m),
a Connect the airbag computer connectors.
REMOVAL
II - FINAL OPERATION.

cardiagn.com
I - REMOVAL PREPARATION OPERATION a Refit the centre console (see Centre console: Re-
moval - Refitting) (57A, Interior equipment).
a Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-3) . a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .
a Remove the centre console (see Centre console:
Removal - Refitting) (57A, Interior equipment).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130870
a Disconnect the airbag computer connectors (1) .
a Remove:
- the airbag computer bolts (2) ,
- the airbag computer bolt (3) ,
- the airbag computer.

88C-9
 AIR BAG AND PRETENSIONERS
Driver's frontal airbag: Removal - Refitting 88C
IMPORTANT
To avoid any risk of damaging the systems, apply
the instructions relating to safety and cleanliness
and the operation recommendations before carry-
ing out the repair (see 88C, Air bag and Preten-
sioners, Airbag and pretensioners: Precautions
for the repair, page 88C-6) .

REMOVAL

I - REMOVAL PREPARATION OPERATION

a

IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or

cardiagn.com
naked flame - they may be triggered.
130965
a Insert a flat-blade screwdriver into the opening locat-
IMPORTANT ed behind the steering wheel.
To prevent the pyrotechnic components from a Unclip the driver's front airbag by pushing the flat-
being permanently deactivated or triggered (air- blade screwdriver upwards.
bags or pretensioners), wait for at least 3 min
after disconnecting the battery.

a Disconnect the battery (see 80A, Battery, Battery:

Removal - Refitting, page 80A-3) .

II - OPERATION FOR REMOVAL OF PART

CONCERNED
a

WARNING
To ensure the airbag is not damaged during
removal, do not use a tool with a point or a sharp
edge.
130966
a

Note:
To disconnect the airbag connector, insert a flat-
blade screwdriver wrapped in adhesive tape in
the notch (1) , lift the security device (2) and dis-
connect the connector.

88C-10
 AIR BAG AND PRETENSIONERS
Driver's frontal airbag: Removal - Refitting 88C
III - FINAL OPERATION.
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

IMPORTANT
To eliminate the risk of any accident, do not
reuse pyrotechnic components.
It is essential to destroy pretensioners or airbags
before scrapping a vehicle or a part only (see
88C, Air bag and Pretensioners, Airbags and
pretensioners: Recycling - Destruction, page
88C-7) .

130967

a Disconnect:

- the driver's front airbag connector (3) ,

cardiagn.com
- the horn connector (4) .

a Remove the driver's front airbag.

IMPORTANT
To prevent the any component from being thrown
upwards, store the airbag with the inflatable
cushion facing upwards.

REFITTING

I - REFITTING PREPARATION OPERATION

IMPORTANT
After a seat belt pyrotechnic component is trig-
gered, it is essential to replace certain parts (see
88C, Air bag and Pretensioners, Airbag and
pretensioners: Precautions for the repair,
page 88C-6) .

II - REFITTING OPERATION FOR PART

CONCERNED

a Connect:

- the horn connector,

- the driver's front airbag connector.

a Fit the driver's front airbag in place.

a Clip the driver's front airbag on to the steering wheel.

88C-11
 AIR BAG AND PRETENSIONERS
Passenger's frontal airbag: Removal - Refitting 88C
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm
a
passenger front airbag 23 N.m
bolts WARNING
To ensure the airbag is not damaged during
removal, do not use a tool with a point or a sharp
edge.
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-6) .

REMOVAL

cardiagn.com
I - REMOVAL PREPARATION OPERATION

a
130871
IMPORTANT
a Remove the front passenger airbag bolt (1) .
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.

IMPORTANT
To prevent the pyrotechnic components from
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min
after disconnecting the battery.

a Disconnect the battery (see 80A, Battery, Battery:

Removal - Refitting, page 80A-3) .

a Remove the glovebox (see Glovebox: Removal -

130872
Refitting) (57A, Interior equipment).
a

Note:
NAVIGATION AID 1 or NAVIGATION AID 2
To disconnect the airbag connector, insert a flat-
a Remove: blade screwdriver wrapped in adhesive tape in
the notch (2) , lift the security device (3) and dis-
- the navigation computer (see 8 3 C, On-board connect the connector.
telematics system, Navigation computer: Re-
moval - Refitting, page 83C-3)

- the navigation interface unit (see 83C, On-board

telematics system, Navigation interface unit:
Removal - Refitting, page 83C-4)

88C-12
 AIR BAG AND PRETENSIONERS
Passenger's frontal airbag: Removal - Refitting 88C
a Detach the passenger front airbag (8) from the dash-
board.
a Remove the passenger frontal airbag.

IMPORTANT
To prevent the any component from being thrown
upwards, store the airbag with the inflatable
cushion facing upwards.

REFITTING

I - REFITTING PREPARATION OPERATION

130873
a Always replace the passenger front airbag bolts.
a Disconnect the front passenger airbag connector (4)
.
a Remove the dashboard (see Dashboard: Removal IMPORTANT

cardiagn.com
- Refitting) (57A, Interior equipment). After a seat belt pyrotechnic component is trig-
gered, it is essential to replace certain parts (see
88C, Air bag and Pretensioners, Airbag and
pretensioners: Precautions for the repair,
page 88C-6) .

IMPORTANT
When the passenger front airbag is triggered, the
consequent damage caused to the mountings
always requires the dashboard to be replaced.
Affix the label warning against fitting a rear-facing
child seat on the front passenger seat to the pas-
senger side of the dashboard.

130874 II - REFITTING OPERATION FOR PART

a Remove: CONCERNED
- the front side air distribution duct bolts,
- the front side air distribution duct. NAVIGATION AID 1 or NAVIGATION AID 2
a Refit:
- the navigation interface unit (see 83C, On-board
telematics system, Navigation interface unit:
Removal - Refitting, page 83C-4)
- the navigation computer (see 8 3 C, On-board
telematics system, Navigation computer: Re-
moval - Refitting, page 83C-3)

a Refit:
- the passenger front airbag to the dashboard,

130875 - new passenger front airbag bolts,

a Remove the front passenger airbag bolts (7) . - the front side air distribution duct,

88C-13
 AIR BAG AND PRETENSIONERS
Passenger's frontal airbag: Removal - Refitting 88C
- the dashboard (see Dashboard: Removal - Refit-
ting) (57A, Interior equipment).
a Connect the front passenger airbag connector.
a Refit the passenger front airbag bolt.
a Torque tighten the passenger front airbag bolts
(23 N.m).

III - FINAL OPERATION

a Refit the glovebox (see Glovebox: Removal - Refit-
ting) (57A, Interior equipment).
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

IMPORTANT
To eliminate the risk of any accident, do not
reuse pyrotechnic components.

cardiagn.com
It is essential to destroy pretensioners or airbags
before scrapping a vehicle or a part only (see
88C, Air bag and Pretensioners, Airbags and
pretensioners: Recycling - Destruction, page
88C-7) .

88C-14
 AIR BAG AND PRETENSIONERS
Front (chest-level) side airbag: Removal - Refitting 88C
II - REMOVAL OF PART CONCERNED

Tightening torquesm

chest-level side airbag 7 N.m

nuts

The front (chest-level) side airbag is fitted to the back-

rest of each front seat on the door side.

When it is deployed, the airbag tears the module cover

and the foam and detaches the trim.

IMPORTANT
To avoid any risk of damaging the systems, apply
the instructions relating to safety and cleanliness
and the operation recommendations before carry- 131737
ing out the repair (see 88C, Air bag and Preten-
a Remove:
sioners, Airbag and pretensioners: Precautions

cardiagn.com
for the repair, page 88C-6) . - the covers from the front (chest-level) side airbag
cover bolts,

REMOVAL - the bolts (1) from the front (chest-level) side airbag
cover,

I - REMOVAL PREPARATION OPERATION - the cover (2) from the front (chest-level) side air-
bag.
a
a Detach the clips from the front (chest-level) side air-
IMPORTANT
bag wiring underneath the seat.
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.

IMPORTANT
To avoid causing a fault or triggering a pyrotech-
nic component (airbags or pretensioners), wait
for at least 3 minutes after disconnecting the
battery.

a Disconnect the battery (see 80A, Battery, Battery:

Removal - Refitting, page 80A-3) .

a Remove:

- the front seat (see Complete front seat: Removal 131738

- Refitting) (75A, Front seat frames and runners),
a Remove the nuts (3) from the front (chest-level) side
- the front seat belt stalk (see 88C, Air bag and Pre- airbag.
tensioners, Front seat belt buckle: Removal -
Refitting, page 88C-24) , a Separate the front (chest-level) side airbag (4) from
the seat backrest trim cover (5) .
- the headrest guide (see Front seat headrest
guide: Removal - Refitting) (79A, Seat accesso- a Remove:
ries),
- the front side (chest-level) airbag,
- the front seat backrest trim partially (see Front
seat base trim: Removal - Refitting) (77A, Front - the foam - trim assembly from the front seat back-
seat trim). rest.

88C-15
 AIR BAG AND PRETENSIONERS
Front (chest-level) side airbag: Removal - Refitting 88C
REFITTING

I - REFITTING PREPARATION OPERATION

a

IMPORTANT
After a seat belt pyrotechnic component is trig-
gered, it is essential to replace certain parts (see
88C, Air bag and Pretensioners, Airbag and
pretensioners: Precautions for the repair,
page 88C-6) .

IMPORTANT
To eliminate the risk of any accident, do not
reuse pyrotechnic components.
It is essential to destroy pretensioners or airbags
before scrapping a vehicle or a part only (see

cardiagn.com
88C, Air bag and Pretensioners, Airbags and
pretensioners: Recycling - Destruction, page
88C-7) .

a Always replace the nuts for the front (chest-level)

side airbag.

II - REFITTING PART CONCERNED

a Refit:
- the foam - trim assembly for the front seat backrest,
- the front (chest-level) side airbag to the seat back-
rest trim cover,
- the new nuts for the front (chest-level) side airbag
a Torque tighten the chest-level side airbag nuts (7
N.m).

III - FINAL OPERATION.

a Refit:
- the front seat backrest trim partially (see Front
seat base trim: Removal - Refitting) (77A, Front
seat trim),
- the headrest guide (see Front seat headrest
guide: Removal - Refitting) (79A, Seat accesso-
ries),

- the front seat belt stalk (see 88C, Air bag and Pre-
tensioners, Front seat belt buckle: Removal -
Refitting, page 88C-24) ,
- the front seat (see Complete front seat: Removal
- Refitting) (75A, Front seat frames and runners),
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

88C-16
 AIR BAG AND PRETENSIONERS
Side curtain airbag: Removal - Refitting 88C
Tightening torquesm

side curtain airbag bolts 11 N.m

The side curtain airbag is mounted behind the headlin-

ing.

When inflating, the airbag becomes detached from the

roof lining.

IMPORTANT
To avoid all risk of damage to the systems, apply
130876
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any a
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the Note:

cardiagn.com
repair, page 88C-6) . To disconnect the airbag connector, insert a flat-
blade screwdriver wrapped in adhesive tape in
the notch (1) , lift the security device (2) and dis-
REMOVAL connect the connector.

I - REMOVAL PREPARATION OPERATION

IMPORTANT
To prevent the pyrotechnic components from
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min
after disconnecting the battery.

a Disconnect the battery (see 80A, Battery, Battery:

Removal - Refitting, page 80A-3) .

a Remove the headlining (see Headlining: Removal -

Refitting) (71A, Body internal trim).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.

WARNING
To ensure the airbag is not damaged during
removal, do not use a tool with a point or a sharp
edge.

88C-17
 AIR BAG AND PRETENSIONERS
Side curtain airbag: Removal - Refitting 88C

cardiagn.com
130877

a Disconnect the connector (3) from the side curtain a Remove the side curtain airbag.
airbag.
a Remove the side curtain airbag bolts. REFITTING

I - REFITTING PREPARATION OPERATION

a Always replace the side curtain airbag bolts.

IMPORTANT
In order to ensure that the side curtain airbag
mountings are secure, never refit a side curtain
airbag which has been removed.

IMPORTANT
After a seat belt pyrotechnic component is trig-
gered, it is essential to replace certain parts (see
88C, Air bag and Pretensioners, Airbag and
pretensioners: Precautions for the repair,
page 88C-6) .

130878 II - REFITTING OPERATION FOR PART

CONCERNED
a Unclip the side curtain airbag mounting brackets (4)
. a Fit the side curtain airbag.

88C-18
 AIR BAG AND PRETENSIONERS
Side curtain airbag: Removal - Refitting 88C
a Attach the side curtain airbag mounting brackets.
a Refit the new side curtain airbag bolts.
a Torque tighten the side curtain airbag bolts (11
N.m).
a Connect the side curtain airbag connector.
a Check that the side curtain airbag connector is cor-
rectly locked.

III - FINAL OPERATION

a Refit the headlining (see Headlining: Removal -
Refitting) (71A, Body internal trim).
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

IMPORTANT

cardiagn.com
To eliminate the risk of any accident, do not
reuse pyrotechnic components.
It is essential to destroy pretensioners or airbags
before scrapping a vehicle or a part only (see
88C, Air bag and Pretensioners, Airbags and
pretensioners: Recycling - Destruction, page
88C-7) .

88C-19
 AIR BAG AND PRETENSIONERS
Side impact sensor: Removal - Refitting 88C
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm

side impact sensor N.m

nuts11

IMPORTANT
To avoid any risk of damaging the systems, apply
the instructions relating to safety and cleanliness
and the operation recommendations before carry-
ing out the repair (see 88C, Air bag and Preten-
sioners, Airbag and pretensioners: Precautions
for the repair, page 88C-6) .

REMOVAL

cardiagn.com
I - REMOVAL PREPARATION OPERATION
a

IMPORTANT 130879
To prevent the pyrotechnic components from
being permanently deactivated or triggered (air- a Remove the nuts (1) from the side impact sensor.
bags or pretensioners), wait for at least 3 min
a Disconnect the connector (2) from the side impact
after disconnecting the battery.
sensor.
a Disconnect the battery (see 80A, Battery, Battery:
a Remove the side impact sensor (3) .
Removal - Refitting, page 80A-3) .
a Remove the front pyrotechnic inertia reel (see 88C,
Air bag and Pretensioners, Front side seat belt: REFITTING
Removal - Refitting, page 88C-27) .

I - REFITTING PREPARATION OPERATION

a Always replace the side impact sensor nuts.

II - REFITTING OPERATION FOR PART

CONCERNED

a Refit:

- the side impact sensor,

- the new side impact sensor nuts.

a Torque tighten the side impact sensor nuts11

(N.m).

a Connect the side impact sensor connector.

III - FINAL OPERATION.

a Refit the front pyrotechnic inertia reel (see 88C, Air

bag and Pretensioners, Front side seat belt: Re-
moval - Refitting, page 88C-27) .

88C-20
 AIR BAG AND PRETENSIONERS
Side impact sensor: Removal - Refitting 88C
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

IMPORTANT
To eliminate the risk of any accident, do not
reuse pyrotechnic components.
It is essential to destroy pretensioners or airbags
before scrapping a vehicle or a part only (see
88C, Air bag and Pretensioners, Airbags and
pretensioners: Recycling - Destruction, page
88C-7) .

cardiagn.com

88C-21
 AIR BAG AND PRETENSIONERS
Inhibitor switch: Removal - Refitting 88C
Special tooling required
REFITTING

Car. 1363 Set of trim removal levers. I - REFITTING OPERATION FOR PART
CONCERNED
REMOVAL a Refit the inhibitor switch on the side panel.
a Connect inhibitor switch connector.
I - REMOVAL PREPARATION OPERATION a Clip the side panel onto the dashboard.
a Switch off the ignition.
II - FINAL OPERATION.

II - OPERATION FOR REMOVAL OF PART a Check:

CONCERNED - the operation of the deactivation switch,
- the « airbag OFF » warning light on the instrument
panel.

cardiagn.com
130968

a Unclip the side panel (1) using the tool (Car. 1363).

131075

a Disconnect the inhibitor switch connector (2) .

a Remove the inhibitor switch by pressing on the clips

(3) .

88C-22
 AIR BAG AND PRETENSIONERS
Front seat lap belt pretensioner: Removal - Refitting 88C

130880

Note:

cardiagn.com
The front side seat lap belt pretensioner (1) cannot
be separated from the front side seat belt. In the
event of a fault, replace the front side seat belt (see
88C, Air bag and Pretensioners, Front side seat
belt: Removal - Refitting, page 88C-27) .

88C-23
 AIR BAG AND PRETENSIONERS
Front seat belt buckle: Removal - Refitting 88C
2 - Passenger side front seat belt buckle

Tightening torquesm a Remove the flap and the storage compartment un-
derneath the seat (see Storage compartment and
driver's side front seat 49 N.m flap under the seat: Removal - Refitting) (57A, In-
belt buckle bolt terior equipment).

passenger side front 49 N.m

seat belt buckle bolt

IMPORTANT
Consult the safety and cleanliness advice and oper-
ation recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Air-
bag and pretensioners: Precautions for the
repair, page 88C-6) .

cardiagn.com
REMOVAL
130882
a Disconnect the connector (3) from the passenger
I - REMOVAL PREPARATION OPERATION presence sensor.
a Remove the clip (4) .
a Remove the front seat (see Complete front seat:
Removal - Refitting) (75A, Front seat frames and
runners).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

1 - Driver's side front seat belt buckle

130883
a Disconnect the font seat belt buckle connector (5) .
a Remove:
- the bolt (6) from the front seat belt buckle,
- the front seat belt buckle.

130881

a Disconnect the font seat belt buckle connector (1) .

a Remove:

- the bolt (2) from the front seat belt buckle,

- the front seat belt buckle.

88C-24
 AIR BAG AND PRETENSIONERS
Front seat belt buckle: Removal - Refitting 88C
REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

1 - Driver's side front seat belt buckle

a Refit the front seat belt buckle.
a Torque tighten the driver's side front seat belt
buckle bolt (49 N.m).
a Connect the front seat belt stalk connector.

2 - Passenger side front seat belt buckle

a Refit the front seat belt buckle.
a Torque tighten the passenger side front seat belt
buckle bolt (49 N.m).

cardiagn.com
a Connect the front seat belt stalk connector.
a Refit the clip.
a Connect the connector for the passenger presence
sensor.
a Refit the flap and the storage compartment under-
neath the seat (see Storage compartment and flap
under the seat: Removal - Refitting) (57A, Interior
equipment).

II - FINAL OPERATION.
a Refit the front seat (see Complete front seat: Re-
moval - Refitting) (75A, Front seat frames and run-
ners).

88C-25
 AIR BAG AND PRETENSIONERS
Rear seat belt buckle: Removal - Refitting 88C
REFITTING
Tightening torquesm
REFITTING OPERATION FOR PART CONCERNED
rear seat belt buckle 49 N.m
a Refit the rear seat belt buckles.
bolts
a Torque tighten the rear seat belt buckle bolts (49
N.m).
REMOVAL a Fit the rear seat base in place.

OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
130884
a Pull the tabs (1) on each side of the bench seat.
a Fold the rear seat base down in the direction of the
arrows.

130885
a Remove:
- the bolts (2) from the rear seat belt buckles,
- the rear seat belt buckles.

88C-26
 AIR BAG AND PRETENSIONERS
Front side seat belt: Removal - Refitting 88C
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm

front lap belt preten- 49 N.m

sioner bolt

front pyrotechnic inertia 49 N.m

reel bolt

front side seat belt upper bolt49

N.m

front pyrotechnic inertia N.m

reel bolt49

front side seat belt lower N.m

bolt49
130886
front side seat belt upper bolt49
N.m a Remove cover (1) .

cardiagn.com
REMOVAL

I - REMOVAL PREPARATION OPERATION

IMPORTANT
Never handle the pyrotechnic systems (preten-
sioners or airbags) near to a source of heat or
naked flame - they may be triggered.

IMPORTANT
To prevent the pyrotechnic components from
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min
after disconnecting the battery.
130887
a Disconnect the battery (see 80A, Battery, Battery: a Remove the front side seat belt upper bolt (2) .
Removal - Refitting, page 80A-3) .
a Detach the front side seat belt guide (3) .
a Remove:

- the front sill panel trim (see Front door sill lining:
Removal - Refitting) (71A, Body internal trim),

- the rear inner sill trim (see Rear door sill lining:
Removal - Refitting) (71A, Body internal trim),

- the B-pillar trim (see B-pillar trim: Removal - Re-

fitting) (71A, Body internal trim).

a Move the front seat as far forward as possible.

a Partially pull up the edge of the floor carpet around

the B-pillar trim.

88C-27
 AIR BAG AND PRETENSIONERS
Front side seat belt: Removal - Refitting 88C
- the front pyrotechnic inertia reel bolt (9) ,
- the front pyrotechnic seat belt inertia reel,
- the « front side seat belt - front pyrotechnic inertia
reel - front lap belt pretensioner » assembly.

2 - Passenger side front side seat belt

130876
a

Note:

cardiagn.com
To disconnect the airbag connector, insert a flat-
blade screwdriver wrapped in adhesive tape in
the notch (4) , lift the security device (5) and dis-
connect the connector.

1 - Driver's side front side seat belt

130890

a Disconnect the connector (10) from the front pyro-

technic inertia reel.
a Remove:
- the front pyrotechnic inertia reel bolt (11) ,
- the lower bolt (12) for the front side seat belt,
- the « front side seat belt - front pyrotechnic inertia
reel » assembly.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED

130889
1 - Driver's side front side seat belt

a Disconnect: a Fit the « front side seat belt - front pyrotechnic inertia
reel - front lap belt pretensioner » assembly in place.
- the connector (6) for the front lap belt pretensioner,
a Refit:
- the connector (7) for the front pyrotechnic inertia
reel. - the front lap belt pretensioner,
a Remove: - the front lap belt pretensioner bolt,
- the bolt (8) from the front lap belt pretensioner, - the front pyrotechnic seat belt inertia reel,
- the front lap belt pretensioner, - the front pyrotechnic inertia reel bolt.

88C-28
 AIR BAG AND PRETENSIONERS
Front side seat belt: Removal - Refitting 88C
a Torque tighten: a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .
- the front lap belt pretensioner bolt (49 N.m),
- the front pyrotechnic inertia reel bolt (49 N.m).
IMPORTANT
a Connect: To eliminate the risk of any accident, do not
- the connector for the front lap belt pretensioner, reuse pyrotechnic components.

- the connector for the front pyrotechnic inertia reel. It is essential to destroy pretensioners or airbags
before scrapping a vehicle or a part only (see
a Connect the front pyrotechnic inertia reel connector. 88C, Air bag and Pretensioners, Airbags and
pretensioners: Recycling - Destruction, page
a Refit:
88C-7) .
- the front side seat belt guide,
- the upper bolt for the front side seatbelt.
a Torque tighten the front side seat belt (upper
bolt49 N.m).
a Refit the cover.

cardiagn.com
2 - Passenger side front side seat belt
a Fit the « front side seat belt - front pyrotechnic inertia
reel » assembly in place.
a Refit:
- the front pyrotechnic seat belt inertia reel,
- the front pyrotechnic inertia reel bolt,
- the lower bolt for the front side seat belt.
a Torque tighten:
- the front pyrotechnic inertia reel bolt49 (N.m),
- the front side seat belt lower bolt49 (N.m).
a Connect the front pyrotechnic inertia reel connector.
a Refit:
- the front side seat belt guide,
- the upper bolt for the front side seatbelt.
a Torque tighten the front side seat belt (upper
bolt49 N.m).
a Refit the cover.

II - FINAL OPERATION.
a Position the floor carpet.
a Refit:
- the B-pillar trim (see B-pillar trim: Removal - Re-
fitting) (71A, Body internal trim),
- the rear inner sill trim (see Rear door sill lining:
Removal - Refitting) (71A, Body internal trim),
- the front sill panel trim (see Front door sill lining:
Removal - Refitting) (71A, Body internal trim).

88C-29
 AIR BAG AND PRETENSIONERS
Rear side seat belt: Removal - Refitting 88C
Tightening torquesm

rear side seat belt auto- 49 N.m

matic inertia reel bolt

rear side seat belt lower 49 N.m

bolt

rear side seat belt upper 49 N.m

bolt

REMOVAL
130892

I - REMOVAL PREPARATION OPERATION a Remove:

- the cover of the rear side seat belt lower bolt,

a Remove:

cardiagn.com
- the rear side seat belt lower bolt (3) ,
- the rear parcel shelf (see Rear parcel shelf: Re-
moval - Refitting) (57A, Interior equipment), - the rear pillar lower trim (4) (see C-pillar lower
trim: Removal - Refitting) (71A, Body internal
- the rear inner sill trim (see Rear door sill lining: trim).
Removal - Refitting) (71A, Body internal trim),

- the luggage compartment floor trim (see Luggage

compartment floor lining: Removal - Refitting)
(71A, Body internal trim),

- the rear panel trim (see Rear end panel lining:

Removal - Refitting) (71A, Body internal trim).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

130893

a Remove:

- the rear side seat belt cover (5) ,

- the rear side seat belt automatic inertia reel bolt (6)
,

- the « rear side seat belt - rear side seat belt auto-
matic inertia reel » assembly.

REFITTING
130891
I - REFITTING OPERATION FOR PART
a Open the cover (1) of the rear side seat belt upper CONCERNED
bolt.
a Fit the « rear side seat belt - rear side seat belt auto-
a Remove the rear side seat belt upper bolt (2) . matic inertia reel » assembly in place.

88C-30
 AIR BAG AND PRETENSIONERS
Rear side seat belt: Removal - Refitting 88C
a Refit:
- the rear side seat belt automatic inertia reel bolt,
- the rear side seat belt cover.
a Torque tighten the rear side seat belt automatic
inertia reel bolt (49 N.m).
a Refit:
- the lower trim of the C-pillar (see C-pillar lower
trim: Removal - Refitting) (71A, Body internal
trim),
- the rear side seat belt lower bolt.
a Torque tighten the rear side seat belt lower bolt
(49 N.m).
a Refit:
- the cover of the rear side seat belt lower bolt,
- the rear side seat belt upper bolt.

cardiagn.com
a Torque tighten the rear side seat belt upper bolt
(49 N.m).
a Refit the cover of the rear side seat belt upper bolt.

II - FINAL OPERATION.
a Refit:
- the rear panel trim (see Rear end panel lining:
Removal - Refitting) (71A, Body internal trim),
- the luggage compartment floor trim (see Luggage
compartment floor lining: Removal - Refitting)
(71A, Body internal trim),
- the rear inner sill trim (see Rear door sill lining:
Removal - Refitting) (71A, Body internal trim),
- the rear parcel shelf (see Rear parcel shelf: Re-
moval - Refitting) (57A, Interior equipment).

88C-31
 AIR BAG AND PRETENSIONERS
Rear centre seat belt: Removal - Refitting 88C
Tightening torquesm

rear centre seat belt 49 N.m

automatic inertia reel
bolt

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove:
- the headrests from the rear seats,
130895
- the rear centre armrest (see Rear centre armrest:
Removal - Refitting) (79A, Seat accessories), a Remove:

- the rear seat backrest (see Complete rear seat: - the rear centre seat belt automatic inertia reel bolt
Removal - Refitting) (76A, Rear seat frames and (3) ,

cardiagn.com
runners), - the nuts (4) for the rear centre seat belt guide,
- the rear seat backrest trim (see 1/3 and 2/3 rear - the « rear centre seat belt - rear centre seat belt au-
bench seatback trim: Removal - Refitting) (78A, tomatic inertia reel » assembly.
Rear seat trim).

REFITTING
II - OPERATION FOR REMOVAL OF PART
CONCERNED
I - REFITTING OPERATION FOR PART
CONCERNED
a Fit the « rear centre seat belt - rear centre seat belt
automatic inertia reel » assembly in place.
a Refit:
- the rear centre seat belt automatic inertia reel bolt,
- the nuts for the rear centre seat belt guide.
a Torque tighten the rear centre seat belt automatic
inertia reel bolt (49 N.m).
a Refit:
- the rear centre seat belt automatic inertia reel cov-
er
130894
a Remove: - the clips.

- the clips (1) ,

II - FINAL OPERATION.
- the rear centre seat belt automatic inertia reel cov-
er (2) . a Refit:
- the rear seat backrest trim (see 1/3 and 2/3 rear
bench seatback trim: Removal - Refitting) (78A,
Rear seat trim),
- the rear seat backrest (see Complete rear seat:
Removal - Refitting) (76A, Rear seat frames and
runners),
- the rear centre armrest (see Rear centre armrest:
Removal - Refitting) (79A, Seat accessories),

88C-32
 AIR BAG AND PRETENSIONERS
Rear centre seat belt: Removal - Refitting 88C
- the rear seat headrests.

cardiagn.com

88C-33
 AIR BAG AND PRETENSIONERS
Passenger airbag deactivation warning light: Removal - Refitting 88C
Special tooling required

Car. 1363 Set of trim removal levers.

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the control panel (see Control panel: Re-
moval - Refitting) (61A, Heating).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
131495
a Unclip the clips (2) on both sides.
a Remove the passenger front airbag deactivation
switch warning light.

REFITTING

131494 I - REFITTING OPERATION FOR PART

a Remove the hazard warning light switches and the CONCERNED
central locking switches (1) using the tool (Car. a Refit the passenger front airbag deactivation switch
1363). warning light.
a Disconnect the connectors. a Connect the connectors.
a Refit the hazard warning light switches and the cen-
tral locking switches.

II - FINAL OPERATION.
a Refit the control panel (see Control panel: Remov-
al - Refitting) (61A, Heating).

88C-34
 AIR BAG AND PRETENSIONERS
Seat belt reminder warning light: Removal - Refitting 88C
Special tooling required

Car. 1363 Set of trim removal levers.

REMOVAL

I - REMOVAL PREPARATION OPERATION

a Remove the control panel (see Control panel: Re-
moval - Refitting) (61A, Heating).

II - OPERATION FOR REMOVAL OF PART

CONCERNED

cardiagn.com
131497
a Unclip the clips (2) on both sides.
a Remove the passenger seat belt warning light.

REFITTING

I - REFITTING OPERATION FOR PART

131496 CONCERNED
a Remove the hazard warning light switches and the a Refit the passenger seat belt warning light.
central locking switches (1) using the tool (Car.
1363). a Connect the connectors.

a Disconnect the connectors. a Refit the hazard warning light switches and the cen-
tral locking switches.

II - FINAL OPERATION.
a Refit the control panel (see Control panel: Remov-
al - Refitting) (61A, Heating).

88C-35
 AIR BAG AND PRETENSIONERS
Front impact sensor: Removal - Refitting 88C
II - REMOVAL OF PART CONCERNED

Tightening torquesm

front impact sensor nuts 11 N.m

IMPORTANT
To avoid any risk of damaging the systems, apply
the instructions relating to safety and cleanliness
and the operation recommendations before carry-
ing out the repair (see 88C, Air bag and Preten-
sioners, Airbag and pretensioners: Precautions
for the repair, page 88C-6) .

IMPORTANT
To eliminate the risk of any accident, do not reuse

cardiagn.com
pyrotechnic components.
It is essential to destroy pretensioners or airbags
before scrapping a vehicle or a part only (see 88C, 131383
Air bag and Pretensioners, Airbags and preten-
a Remove:
sioners: Recycling - Destruction, page 88C-7) .
- the front impact sensor nuts (1) ,
- the front impact sensor cover (2) .
REMOVAL

I - REMOVAL PREPARATION OPERATION

a

IMPORTANT
To prevent the pyrotechnic components from
being permanently deactivated or triggered (air-
bags or pretensioners), wait for at least 3 min-
utes after disconnecting the battery.

a Disconnect the battery (see 80A, Battery, Battery:

Removal - Refitting, page 80A-3) .
a Remove the front bumper (see Front bumper: Re-
moval - Refitting) (55A, Exterior protection).

131384
a Disconnect the front impact sensor connector (3) .
a Remove the front impact sensor (4) .

REFITTING

I - REFITTING PREPARATION OPERATION

a Always replace the front impact sensor nuts.

88C-36
 AIR BAG AND PRETENSIONERS
Front impact sensor: Removal - Refitting 88C
II - REFITTING PART CONCERNED
a Refit the front impact sensor.
a Connect the front impact sensor connector.
a Refit:
- the front impact sensor cover,
- the front impact sensor nuts.
a Torque tighten the front impact sensor nuts (11
N.m).

III - FINAL OPERATION.

a Refit the front bumper (see Front bumper: Remov-
al - Refitting) (55A, Exterior protection).
a Connect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-3) .

cardiagn.com

88C-37
 DRIVER'S POSITION
Cigarette lighter: Removal - Refitting 88D
REMOVAL

I - REMOVAL PREPARATION OPERATION

131580
a Remove:
- the lower covers (3) from the centre panel on both
130758 sides,

cardiagn.com
a Remove the centre front panel side trim (1) . - the glovebox (see Glovebox: Removal - Refit-
ting) ( 57A, Interior equipment),
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment).

131581
131579 a Remove:
a Remove the plate (2) from the gear lever (see Cen- - the lower trims (4) from the centre panel on both
tre console: Removal - Refitting) (57A, Interior sides,
equipment).
- the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) .

88D-1
 DRIVER'S POSITION
Cigarette lighter: Removal - Refitting 88D

132547
a Remove the cigarette lighter socket in the direction
of (9) by moving it in the direction of (10) using a
small flat-blade screwdriver.

cardiagn.com
131582
a Remove:
- the starter control panel bolts (5) ,
- the starter control panel (6) .
a Disconnect the connectors.

II - OPERATION FOR REMOVAL OF PART

CONCERNED
a Remove the cigarette lighter.

132548
a Unclip the bulb support (11) by pulling on the clips
(12) using a flat-blade screwdriver.

REFITTING

I - REFITTING OPERATION FOR PART

CONCERNED
a Clip on the bulb mounting.
a Refit:

132546 - the cigarette lighter socket on the fascia panel,

a Keep the plastic support unlocked at (7) using a - the cigarette lighter mounting,
small flat-blade screwdriver.
- the cigarette lighter.
a Remove the cigarette lighter support in the direction
of (8) .
II - FINAL OPERATION.
a Connect the connectors.
a Refit:
- the starter control panel,

88D-2
 DRIVER'S POSITION
Cigarette lighter: Removal - Refitting 88D
- the starter control panel bolts,
- the radio (see 86A, Radio, Radio: Removal - Re-
fitting, page 86A-4) ,
- the CD multi-changer (see 86A, Radio, CD chang-
er: Removal - Refitting, page 86A-14) ,
- the centre panel lower trims on both sides,
- the dashboard lower cover on the driver's side (see
Dashboard: Removal - Refitting) (57A, Interior
equipment),
- the glovebox (see Glovebox: Removal - Refit-
ting) ( 57A, Interior equipment),
- the centre panel lower covers on both sides,
- the gear lever plate (see Centre console: Remov-
al - Refitting) (57A, Interior equipment),
- the centre front panel side trim.

cardiagn.com

88D-3