X F P Te c h n ic a l S p e c ific a tio n s SINGLE LOOP 16 ZONE XFP PANELS ONE OR TWO LOOP 32 ZONE XFP PANELS

XFP501E/X; XFP501E/H XFP501/X; XFP501/H; XFP502/X; XFP502/H

Power Supply Specification
Mains supply 230V a.c. ± 10% 50/60Hz. Max current 350mA 230V a.± 10% 50/60Hz. Max current 680mA
Internal power supply 27V d.c Nominal 27V d.c Nominal
Total output current limited to 1.4A @ 230V a.c. 3A @ 230 V a.c.
Power rating Imax. a = 210mA; Imin. = 40mA Imax. a = 250mA (1 loop) 270mA (2 loop); Imin. = 70mA
Maximum internal resistance Ri max. - 1.1Ω Ri max. - 1.1Ω
Supply and battery charger monitored for failure Yes Yes
Batteries monitored for disconnection and failure Yes Yes
Batteries protected against deep discharge Yes Yes
Max. battery size and type 3.2 Ahr VRLA 7.0 Ahr VRLA
Specified batteries for LPCB approved systems 2 x Yuasa NP3.2-12 2 x Yuasa NP7-12
Quiescent current drain < 50mA (1 loop unloaded) < 80mA (1 loop unloaded); <100mA (2 loops unloaded)
Earth fault monitoring Yes (any conductor) Yes (any conductor)
Temperature compensated charging Yes Yes

Loop Driver Specification

range
Number of loop drivers 1 1 (XFP501/X ; XFP501/H); 2 (XFP502/X, XFP502/H)
Line monitored for open and short circuit faults Yes Yes
Onboard loop isolators with LED indication when active Yes Yes
Auto-polling from each loop end Yes Yes
Max. loop output current 500mA (Voltage: 25V min, 34V max) 500mA (Voltage: 25V min, 34V max)
Max. number of addressable devices per loop 126 126
Max. number of loop powered sounders per loop @ 10mA 40 40
Number of programmable sounder groups 16 16
Number of programmable output sets 16 16

Conventional Sounder Circuit Specification

Number of programmable circuits 2 2
End of line resistor value
Line monitored for open and short circuit faults
Outputs fused at
6800 Ω 5% Tol. 0.25 W
Yes
400mA. Protected by resettable overload circuit
6800 Ω 5% Tol. 0.25 W
Yes
400mA. Protected by resettable overload circuit
NOW W ITH RFACE
E
USER INT
Output voltage 19.5V minimum; 28V maximum 19.5V minimum; 28V maximum

OVED TCHSWI
AN IMPR ED KEYPAD/KEYRD
Max. number of sounders @ 20mA 40 80

Auxiliary Outputs
IN
Type Relay voltage free single pole changeover
& COMB TRY AS STANDA
Max switching current
Max switching voltage
1A
30 V d.c EN
Relay 1/ Relay 2 / Relay 3 Programmed from cause and effect
Fault Active when no faults are present
‘24V’ Aux Power Output 19.5V min, 28V max. Max current 100mA. Protected by resettable overload circuit

Auxiliary Inputs
Input 1 Connect to 0V to trigger. Max input voltage 27V d.c. (non-latching). Programmable from cause and effect.
Input 2 Connect to 0V to trigger. Max input voltage 27V d.c (non-latching). Programmable from cause and effect.

Fuses (to IEC - EN60127 Pt2)

Mains Fuse 1A HRC Ceramic 20mm 1A HRC Ceramic 20mm
Battery Fuse - limits the current drawn from the battery 1.6A F 20mm 3.15A F 20mm

Panel Indicators and Controls

Keyswitch Plastic key operated Metal key operated
Control buttons Silence, Reset, Resound, Investigate; More Information; Menu
Event scrolling and menu access buttons Up (1); Down (2); Accept (3); Abort (4)
Liquid Crystal Display Two lines x 40 characters, backlit
Number of Zonal LED indicators 16 32
Other LED indicators General Fire, System Energised; Pre-Alarm; Remote Output Activated; Menus Accessed; Disablement;
Test; Remote Output Disabled; Silenced; General Fault; System Fault;

Physical Dimensions
Approx. dimensions of back box (W x H x D) 380 x 235 x 77mm (plastic). Includes ‘lip’. 410 x 250 x 80mm (metal)
Approx. dimensions of lid (W x H x D) 380 x 235 x 16mm (plastic) 439 x 274 x 7mm (metal)
Approx. weight (without batteries) 1.8Kg 4.5kg

Cabling Requirements
Type of cable Fire resistant screened cable, minimum size 1mm2
Max. cable length per loop 1km
Connector blocks Plug-on type, largest acceptable conductor size 1.5mm2
Max. allowable loop impedance (each conductor) 20 Ω
Max. cable capacitance .27µF

Network Specification
Connection Via CFP761 network driver card fitted at main panel Via AFP711 network driver card fitted at main panel
Max. no. of main panels per network 8 8
Max. no of repeaters per non-networked main panel 8 8
Max. cable length per network 1km (main panel network); 500m (repeater network) 1km (main panel network); 500m (repeater network)

PC/Printer Interface
PC connection Via main panel RS232 molex connector (lead supplied in XFP507 upload/download software kit)
Printer connection Not applicable Via main panel RS232 connector block.

Operating conditions
The components are selected to operate within their specification when the environmental conditions outside the enclosure comply with class 3k5 of IEC 721-3-3 : 1978.
Temperature range:- -5 to +40oC. Maximum relative humidity: 95%

© Errors and omissions excepted.

Context Plus operates a policy of continuous improvement and we
reserve the right to alter product specifications at our discretion and without prior notice.
Approved Document No. DML0503400 Rev 1

Authorized Distributor for Asia Pacific

Manufactured in
Stephens Way, Wigan,
WN3 6PH. England
www.demcoalarm.com

Lot 3928, Jalan Keretapi Lama

Visit our website at www.contextplus.co.uk Off Jalan Kapar 5 1/2 Miles
42100 Klang
Selangor Darul Ehsan
West Malaysia
Tel: +603-3290 3333
DE MCO-1 2 -11-V 1

Fax: +603-3290 2288

Quality System Certificate No: 176
Assessed to ISO9001 : 2008 E-mail: sales@ demcoalarm.com

Quality without Compromise

1 or 2 loop EN54 networkable analogue addressable fire alarm panels TYPICAL WIRING

Below is a diagram of a typical XFP analogue addressable loop fitted with a KEY FEATURES OF THE XFP’S NETWORK PROTOCOL
Context Plus’s XFP range of networkable analogue selection of detectors, loop powered sounders, modules and isolators, all connected The XFP’s network protocol allows the interconnection
addressable fire panels offer high performance to an XFP single loop 16 zone panel. of up to eight XFP main panels (any mix) over a two-
The diagram also illustrates how a series of XFP main panels can be networked wire RS485 network. Alternatively, the network can be
at a competitive price. used to connect up to eight XFP repeaters to one XFP
using the range’s powerful RS485 network.
main panel. It is not possible to mix XFP main panels
Certified to the latest versions of and repeaters on the same network.
EN54 parts 2 & 4 by the Loss Prevention Key features of the XFP’s network protocol when
Certification Board, two versions are used for interconnecting XFP main panels:

range
Zone Monitor Detector c/w
with Isolator c c c Mounting Base
available - a cost-effective single loop EOL Allows the interconnection of up to eight XFP
Sounder control main panels (any mix of single loop 16 zone XFPs
16 zone panel in a plastic enclosure and unit with Isolator
Conventional detectors and manual call points Detector c/w
Isolating Base and 1 and 2 loop 32 zone XFPs).
a robust 1 or 2 loop 32 zone metal panel. Local
24V Up to 1 km of cable may be fitted to an XFP main
PSU c c c EOL Manual
Call Point panel network.
Ideal for use in office blocks, shopping complexes Externally powered conventional sounders
Each networked XFP main panel can be
and big industrial sites as well as smaller stand-alone Hush button
c c
Fire Output Loop Powered programmed to accept Fires, Faults and Control
with Isolator Fault Input Sounder
applications, both versions offer an array of user EOL
actions such as Silence Alarm Sounders and
and installer-friendly features, including:-
Conventional detectors, manual call points and sounders Input Output Unit Loop Powered Control Panel Reset from other main panels. They
Beacon
c c EOL
with Isolator will also Accept Disablement commands for zones,
sounders and output sets from other main panels.
Full compatibility with Apollo’s XP95/Discovery and All panels monitor all other panels for network
Important: Isolators should be installed at intervals not exceeding Ancillary function
Hochiki’s ESP protocols 20 devices and at the building's structural fire barriers/zonal boundaries. wiring faults.
Fires on remote panels are displayed on local panels
The ability to interconnect up to eight XFP main panels including the point description of the alarm’s origin.
(any variant) onto a two wire RS485 network. Alternatively, Switch Monitor Faults on remote panels are displayed on local panels
XFP single loop 16 zone panel up to eight XFP repeaters can be connected to a with Isolator including the point description of detectors.
Relay output 1 Programmable input 1
non-networked XFP main panel Relay output 2 Programmable input 2 Cause and effects can be programmed into local
Relay output 3
Fault output Conventional Sounder Circuit 1 panels dependent on which remote panel is in alarm.
Combined keypad / keyswitch entry to Access Levels 2 & 3 +24V output Conventional Sounder Circuit 2
The network supports the programming of site data
into remote panels from a PC at a local panel.
Two independently programmable conventional sounder circuits
Time and date is common to all panels throughout
the network.
Two programmable inputs
All networked main panels require a network
A fault output relay and three programmable relay outputs communication card.
with voltage free changeover contacts Key features of the XFP’s network protocol when
used for connecting XFP repeaters
Three zone dependency functions (A, B & C to EN54-2 Clause 7.12) Allows the connection of up to eight XFP repeaters
to one non-networked main panel. The XFP main
A day/night (building occupied/unoccupied) function panel must have a network communication card fitted.
Up to 500m of cable may be fitted to an XFP
An investigation delay period function repeater network.
This diagram is provided for illustration purposes only and you should always refer to the relevant XFP panel/device
instructions as appropriate before installation. Note that the descriptions and availability of the devices shown may not Each XFP repeater offers all the functions and
XFP 1 or 2 loop 32 zone panel Individual sensitivity settings for each device controls of an XFP main panel.
be applicable to all manufacturer’s protocols.
A phased evacuation and delays to outputs facility (to EN54-2
Clause 7.11)
XFP ORDER CODES
An alarm counter that records the number of times the
XFP SINGLE LOOP 16 ZONE FIRE PANELS - LPCB approved to EN54-2/4
_________________________________________________________________________ XFP BEZELS/ENCLOSURES* for XFP 32 zone main & repeater panels only
________________________________________________________________________
panel has been in an alarm state (to EN54-2 Clause 7.13)
XFP501E/X XFP Networkable single loop 16 zone panel (XP95/Discovery) AFP385 Flush mount bezel (for XFP 32 zone main & repeater panels)
________________________________________________________________________
Keypad/keyswitch entry, c/w 1.4A psu, plastic enclosure
________________________________________________________________________ BF359/3S Stainless steel glazed enclosure (for XFP 32 zone panels only)
________________________________________________________________________
Powerful short circuit protected loop drivers, capable of
XFP501E/H XFP Networkable single loop 16 zone panel (Hochiki ESP) BF359/3CL Cam lock kit for BF359/3S enclosure
________________________________________________________________________
supporting up to 40 loop powered 10mA sounders per loop Keypad/keyswitch entry, c/w 1.4A psu, plastic enclosure
_________________________________________________________________________ BF359/3SL Electromagnetic solenoid lock kit for BF359/3S enclosure
________________________________________________________________________
An integral EN54-4/A2 switch mode PSU rated @ 185-260V a.c. Note that XFP 16 zone panels have been designed so they can be surface
XFP 1 LOOP 32 ZONE FIRE PANELS - LPCB approved to EN54-2/4 or semi-flush mounted without the need for an additional bezel
50/60Hz (1.4A on a 16 zone panel, 3A on a 32 zone panel) _________________________________________________________________________ ________________________________________________________________________
XFP501/X XFP Networkable one loop 32 zone panel (XP95/Discovery) XFP NETWORK COMMUNICATION CARDS*
Earth fault monitoring Keypad/keyswitch entry, c/w 3A psu, metal enclosure
_________________________________________________________________________ ________________________________________________________________________
CFP761 XFP network communication card for XFP 16 zone main panels
________________________________________________________________________
XFP501/H XFP Networkable one loop 32 zone panel (Hochiki ESP)
An easy to read, 80 character back-lit display Keypad/keyswitch entry, c/w 3A psu, metal enclosure AFP711 XFP network communication card for XFP 32 zone main panels
________________________________________________________________________
_________________________________________________________________________
(One network communication card is required per networked main panel. Note that
repeater panels are supplied with a network communication card already fitted).
40 characters of custom text per device XFP 2 LOOP 32 ZONE FIRE PANELS - LPCB approved to EN54-2/4
_________________________________________________________________________
Stainless steel enclosure XFP PROGRAMMING SOFTWARE*
________________________________________________________________________
XFP502/X XFP Networkable two loop 32 zone panel (XP95/Discovery)
999 event monitoring Keypad/keyswitch entry, c/w 3A psu, metal enclosure XFP507 XFP Upload download software kit (all protocols)
_________________________________________________________________________
Windows 98, 2000, XP. Includes programming lead
________________________________________________________________________
XFP502/H XFP Networkable two loop 32 zone panel (Hochiki ESP)
Comprehensive test facilities (to EN54-2 Clause 10) and a wide Keypad/keyswitch entry, c/w 3A psu, metal enclosure SAF7070000 2m Programming lead ONLY
________________________________________________________________________
_________________________________________________________________________
range of maintenance & commissioning functions including
XFP PRINTER KITS*
________________________________________________________________________
auto-learn loops, monitor a point, test outputs, one man XFP REPEATERS*
________________________________________________________________________
walk test and loop continuity test AFP709 XFP off-board printer kit
________________________________________________________________________
XFP510-16 XFP Networkable repeater panel, 16 zones (all protocols)
Keypad/keyswitch entry, c/w psu, plastic enclosure
________________________________________________________________________
An intuitive Windows based upload-download PC program * Repeaters, bezels / enclosures, network communication cards,
XFP510-32 XFP Networkable repeater panel, 32 zones (all protocols) programming software and printer kits are not included within the
that allows the system to be programmed quickly and easily Keypad/keyswitch entry, c/w psu, metal enclosure
________________________________________________________________________ scope of the XFP’s LPCB approval

Full compatibility with Context Plus’ Hush Button fire alarm

solution for houses of multiple occupation WHY LPCB?
The LPCB stamp of approval is recognised worldwide and
Optional flush-mounting stainless steel enclosures available
(for 32 zone XFP panels only) demonstrates that the XFP has been tested and certified
Sophisticated sounder group mapping (above) and complex
cause and effect scenarios can be easily implemented using as being compliant with EN54 parts 2 and 4 by the Loss
the XFP’s intuitive upload-download programming software. Prevention Certification Board.