1 2 3 4

CODE AND SPECIFICATIONS

CODE: ASME, SECT.VIII, DIV.1, ED.2015. TEMA NINTH EDITION
TEMA CLASS: "R", TYPE BEU
115 in [2921,00 mm] STAMPED: TUBE BUNDLE, YES "U"PART
406 11/16 in [10329,93 mm] USER'S DESIGN REQUIREMENTS: UDR-16002-PC-HT
101 in [2565,15 mm]
INSPECTED BY: AUTHORIZED INSPECTOR (HSBCT)
393 3/16 in [9987,03 mm]

DESIGN DATA (TUBE BUNDLE)

390 1/4 in [9912,35 mm]
N3 N3 N3 MAXIMUM ALLOWABLE WORKING PRESSURE 151 psig
126 1/8 in [3203,58 mm] 126 1/8 in [3203,58 mm] MAXIMUM DESIGN TEMPERATURE 151 °F
WORKING PRESSURE 20.01 psig
WORKING TEMPERATURE 127.22 °F
CORROSION ALLOWANCE 0.0
MINIMAL DESIGN METAL TEMPERATURE 32 °F @ 151 psig
HYDROSTATIC PRESSURE TEST 196,3 psig
BB BB IMPACT TEST YES, ONLY TUBESHEET TO -40 °F PER UHA (a)
HEAT TREATMENT NO
SERVICE CONSIDERATION NO LETHAL
FLUID CIRCULATED (TUBE SIDE) WATER

106 5/8 in [2708,28 mm]

107 7/8 in [2740,03 mm]

TUBE TO TUBESHEET JOINT WELDED AND EXPANDED
NO. PASS PER SHELL 2
N2 N1 NDE: (FOR BUNDLE)

172 15/16 in [4392,61 mm]

JOINT EFFICIENCY: N/A
GAS RADIOGRAPH EXAM: N/A
N2 N1

FLOW MATERIALS
U TUBES SA-789-S32750
TUBESHEET SA-182-F60-S32750

104 7/8 in [2663,83 mm]

BAFFLES AND SUPPORT PLATE SA-240-TP 316L
SEALING STRIP SA-240-TP 316L
IMPINGEMENT PLATE SA-240-S32205
TIE ROD SA-479-S32205
SPACER SA-789-S32750
IMPINGEMENT ROD SA-479-S32205
SLIDING PLATE SA-479-S32205
A PIN GUIDE SA-479-S32205 A
NUTS SA-194-S32205

N4 N4 N4

WEIGHT
LIFT WEIGHT xxxx
42 13/16 in [1087,44 mm]
PAINTING AND SURFACE PREPARATIONS
7 in [177,80 mm] 7 in [177,80 mm] 399 3/8 in [10144,89 mm] SYSTEM APPLY FOR SURFACE PRIMER MID COAT TOP COAT DFT MILS
N/A N/A N/A N/A N/A N/A N/A
31 1/8 in [791,16 mm]
84 in [2133,59 mm] GENERAL NOTES
13
1.- ALL DIMENSIONS ARE IN INCHES [MILIMETERS] UNLESS OTHERWISE IS INDICATED.

14 2.- ANY MACHINING OPERATIONS BURRS SHALL BE REMOVED AND GIVEN A WORKMANLIKE FINISH.
12
3.- TOLERANCES FOR TUBE HOLES IN TUBESHEET: ±0.002 in [±0.05 mm]
9
7 8 4.- THE SURFACE FINISH FOR TUBE HOLES WILL BE [RESEARSCH]
61 1/2 in [1561,82 mm]

24) B 2-A 22) 5.- THE LOCATION OF DRILLING OPERATIONS IN TUBESHEET AND BAFFLES IS REFERRED FROM THE
4
23) 22) 2-B 21) CENTERLINE OF PIECES, MEASURES MUST HAVE TOLERANCES 0.005 in [0.127 mm].
4 21)
22) 2-B 20)
20) 4
21) 2-B 19)
4
6.- TOLERANCE FOR TUBESHEET EXTERNAL DIAMETER: `
1
6 20) 19) 2-B 18) 16 in [±1,5875 mm].
18) 4
19) 2-B 17)
4 17)
18) 2-B 16)
4 7.- TOLERANCES FOR TUBESHEET INTERNAL DIAMETERS: ±1/32"[±0.8]
17) 16) 2-B 15)
5 4 15)
16) 2-B 14)
14) 4 8.- TOLERANCES FOR GROOVES:
15) 2-B 13)
11 4 13) DEPTH: +0"[+0], -1/32"[-0.8]
14) 2-B 12)
4 WIDTH: ±1/16"[±1.6]
13) 12) 2-B 11)
4 11)
12) 2-B 10)
10) 4
11) 2-B 9) 9.- TOLERANCE +0"[+0], -1/32"[-0.8] WHERE INDICATED.
47 15/16 in [1217,61 mm]

61 1/2 in [1561,82 mm]

4
10) 9) 2-B 8)
8) 4
9) 2-B 7) 10.- TOLERANCE ±1/16"[±1.6] WHERE INDICATED.
4 7)
8) 2-B 6)
4
7) 6) 2-B 5)
4 11.- NOMINAL LENGTH FOR U-TUBES IS THE STRAIGHT LENGTH FROM END OF TUBE TO BEND TANGENT.
6) 5) 2-B 4)
4) 4
5) 1-B 3)
3 12.- EXPAND TUBES AFTER WELDING.
4) 3) 1-B 2)
2) 3
3) A 1-A 1)
2) 1) 13.- FOR BILL OF MATERIALS SEE DGW 16002-PC-HT-GEN-002.
1)
14.-TOLERANCE FROM TUBESHEET TO LAST BAFFLE: ±1/8 [±3.20].
BL
GAS FLOW 15.-TOLERANCE FROM BAFFLE TO BAFFLE: ±1/8 [±3.20].

9 3/16 in [233,09 mm] 16.-STAMPING TO BE LOCATED ON TUBESHEET OD.

18 11/16 in [474,93 mm] 17.-FOR STAMPING THE MINIMUM HIGH OF LETTERS IS 5/16".

o4 in [101,60 mm] 18.-STAMPING MARK SHALL BE PERFORMED AS FOLLOWING:

SECTION BB-BB
SCALE 1/30
4 in [101,60 mm]

BILL OF MATERIAL
ITEM QTY PART DESCRIPTION MATERIAL
1 72 STRAIGHT SMLS FINNED TUBE 2 in [50,8 mm] OD, 0.135 in [3,429 mm] M.W. SA-213 Gr.T22
DETAIL BL 2 456 STRAIGHT SMLS FINNED TUBE 2 in [50,8 mm] OD, 0.135 in [3,429 mm] M.W. SA-192
3 48 180° RETURN BEND 2 in [50,8 mm] OD, 0.135 in [3,429 mm] M.W. SA-234 Gr. WP22 S58
SCALE 1 / 15 4 456 180° RETURN BEND 2 in [50,8 mm] OD, 0.135 in [3,429 mm] M.W. SA-234 Gr. WPB S58

10 BN 5 2 BUTT WELD TEE REDUCCION NPS 8X6, SCH80 SA-234 WPB

BK 6 4 SMLS PIPE NPS 8, SCH 80, LONG 40. 3/4 in [1035,05 mm] SA-106 Gr. B

7 4 BUTT WELD CAP NPS 8, SCH80 SA-234 WPB

X1 F X2 8 4 SMLS PIPE NPS 1. 1/2, SCH 80, LONG 6. 1/16 in [154 mm] SA-106 Gr. B
9 4 WN FLANGE NPS 1. 1/2, RF, CL 600, SCH 80 SA-105

B
BE 10 2 SMLS PIPE NPS 6, SCH 80, LONG 7 in [117,8 mm] SA-106 Gr. B B
1
BH 11 2 WN FLANGE NPS 6, RF, CL 600, SCH 80 SA-105
BODY ASTM A105, RF FLANGED CLASS 600, TRIM
12 14 GATE VALVE BOLTED BONNET SA-105
BJ 8
DETAIL BM 13 4 BLIND FLAGE NPS 1. 1/2, RE, CL 600 SA-105
L
SCALE 1 / 5
DETAIL BG
SCALE 1 / 8 TABLE
GS-1-1-G-1 ITEM L F X1 X2
GS-5-1-G-7 A 404. 5/8 in [10277,475 mm] 386. 1/4 [9810,75 mm] 3. 3/8 in [85,725 mm] 9. 5/8 in 244,475 mm]
60° ±5° 5/32" 60,0° `5° GS-1-1-G-1 B 393 in [9982,2 mm] 386. 1/4 [9810,75 mm] 3. 3/8 in [85,725 mm] 3. 3/8 in [85,725 mm]
38~
GS-1-1-G-1
GS-5-5-G-6 T22
7/16"x3/8"
5/32" 3/16
+0
- 1/16 [
in 5,29 + ,0
- 1,6
mm
]
38~
GS-5-1-G-7 ENGINEERING DEPARTMENT QA/QC DEPARTMENT
1/8" 3/8"
60°~

APPROVED:_____ DATE____ APPROVED:_____ DATE____

GENERAL ARRANGEMENT 16003-PS-CRF-MEC-GEN-001 TAG No: SERIAL No: JOB NUMBER (OT):
tc:1/4
+0
- 1/8 [
in 6,39 + ,0
- 3,2
mm
] 1/8 in [3,18 mm]
DETAIL BN DWG N~

GS
1/8 `1/16 in [3,18 `1,6 mm] REFERENCES 03S306/07/08 V-111002/3/4 16003-PS-CRF
TITLE:
TABLE OF NOZZLES INTERNAL DETAILS
SCALE 1 / 2 PROJECTION CARTRIDGE FILTER
MARK QTY SERVICE NPS CLASS TYPE SCH
TO C.L/R.L 03S306/07/08 GLOBAL SUPPLY
DETAIL BJ DETAIL BK
DETAIL BE DETAIL BH N1 1 FEEDWATER INLET 6 600 Lb WN RF 80 INDICATE
DWG: REVISED: APPROVED: P.: 1
SCALE 1 / 2 SCALE 1 / 2
N2 1 FEEDWATER OUTLET 6 150 Lb WN RF 80 INDICATE A.R J.L A.R. OF: 1
SCALE 1 SCALE 1 / 2 N3 2 VET 1. 1/2 -- WN RF 80 INDICATE 0 10-10-18 FIRST ISSUED A.R J.L A.R. DATE: DWG N°: SCALE: REV:
N4 2 DRAIN 1. 1/2 -- WN RF 80 INDICATE REV DATE: REVISIONS DWG. REV. APP. 10-10-18 16003-PS-CRF-MEC-DET-001 S/E 0

SIZE A1 1 2 3 4