MS/MSX
OFF GRID SOLAR INVERTER
MPPT 25A/60A! LCD DISPLAY
HIGH FREQUENCY PURE SINE WAVE
AC CHARGER USB PORT
STACKABLE* PB ACID/LIFEPO4
* Only on 48V models
MONITORING SOFTWARE — WATCHPOWER
KEY FEATURES
● Built-in MPPT 60A solar charger ● Inverter+ AC Charger + Solar Charger 3-in-1 design
● Max AC charging up to 60A (48v models only) ● Pure sine wave output
● Max total system charging: 60A + 60A = 120A !! ● 2X surge capacity up to 5 seconds
● High frequency, light-weight design ● USB communication
● Highly programmable menu ● LCD monitor display system info + LED indicators
● Wide AC input range ● FREE monitoring software included
● Adjustable Bulk/Float Voltage ● Built-in generator starter dry contact**
● Supports various lead acid batteries, LiFePo4* ● Overload/Overtemp/short circuit protections
● Cold start capability (requires DC)
Only 48V models are PARALLEL–READY.
Optional Parallel Kit required for all units
in parallel and sold separately.
*For LiFePo4 suitability, please check with your battery supplier on charging and BMS requirement.
** Inverter-Generators are recommended for better compatibility
www.inpowers.co │ info@inpowers.co
Specifications
824 1624 2424 2424TSX 3248 4048 1624TSX
ELECTRICAL SPECIFICATIONS
Continuous/Surge Output 800 / 1600W 1.6 /3.2KW 2.4 / 4.8KW 2.4 / 4.8KW 3.2 / 6.4KW 4.0 / 8.0KW 1.6 / 3.2KW
Surge Rating 5 seconds max, 2X 5 seconds max 2X
Input Power Factor 0.8 0.8
Input Voltage Range 90~280VAC (Appliance mode), 170~280VAC (UPS mode) 65~140VAC, 95~140VAC
Input/Output Frequency 50Hz / 60Hz 50Hz / 60Hz
Output Voltage 230VAC±5% 110/120VAC±5%
Output Waveform Pure Sine Wave Pure Sine Wave
Output Regulation/THD < 3% RMS for battery voltage range < 3% RMS
Output Short Circuit Circuit Breaker Circuit Breaker
Peak Efficiency 91% 93% 93%
Nominal DC Voltage 24V (MAX 30V) 48V (MAX 60V) 24V (MAX 30V)
Transfer Time <10ms (UPS mode), <20ms (Appliance mode)** <10ms, <20ms
Charging Mode 3-stage 3-stage
Boost Voltage (Flooded/MF) 29.2V/28.2V 58.4V/56.4V 29.2V/28.2V
Float Voltage (Flooded/MF) 27.0V/27.0V 54.0V/54.0V 27.0V/27.0V
AC Recharging Current 10/20amp 20/30amp 60 amp 10/20amp
No Load Power Consumption <25W <50W <25W
Power Saving Consumption <10W <15W <10W
Solar Charger a
Max PV Input / Output 600W 1500W 3000W 1500W
Max Charging Current MPPT 25A MPPT 60A MPPT 60A
Max PV Input Voc, MPPT Range 75V, 30~66V 145V, 30~115V 145V, 60~115V 145V, 30~115V
Standby Power 2W 2W 2W
ENVIRONMENTAL / MECHANICAL SPECIFICATIONS a
Certification CE CE
Operating/Storage Temp. 0°C ~ 55°C / -15°C~ 60°C 0°C ~ 55°C / -15°C~ 60°C
Operating Humidity 20~90%RH Non-Condensing 20~90%RH N.C.
Dimension 355*272*100mm 479*295*140mm 468*295*140mm 479*295*140mm
Net Weight 7.0Kg 7.1Kg 7.5Kg 11.8Kg 11.5Kg 11.5Kg 11.8Kg
** Transfer time may be longer (30ms) when used in parallel configuration and this may cause interruption in certain load.
1 YEAR STANDARD WARRANTY PERIOD (3 YEARS EXTENDED)
*Product specifications are subject to change without prior notice
Optional Accessories
This accessory is applicable only to the
48VDC models of HS and MS series
inverter. It is a required component to
be installed in every unit of a parallel
system. A parallel kit includes:
● 1 X PARALLEL BOARD
● 1 X PARALLEL COMM CABLE
● 1 X CURRENT SHARING CABLE
*IMPORTANT: please do not wire 12v or 24v HS/TS inverters in parallel, as this will result instant
damage of all units!
This device is an extension of the HS/MS inverter’s
LCD module and allows user to implement control
on settings and monitoring from a distance away.
This remote module can coexist with the built-in
LCD device and is compatible with all models
12v/24v/48v in the HS/MS inverter series.
*Maximum operating distance: 15m via RJ45 net-
work cable
*Product specifications are subject to change without prior notice
