Electric Double Layer Capacitors DLCAP(TM)

DLCAPTM
Electric Double Layer Capacitors

NO INDEX
1 Summary Introduction
2 Cyrindrical Type DLA Series 2.5V Standard type
3 Cyrindrical Type DLB Series 2.5V Energy type
4 Cyrindrical Type DLC Series 2.5V Power type
5 Cyrindrical Type DMA Series 2.3V High capacity standard type
6 Cyrindrical Type DMB Series 2.3V High capacity energy type
7 Cyrindrical Type DMC Series 2.3V High capacity power type
8 Prismatic Type DSC Series 2.5V Super low resistance type
9 Prismatic Type DTC Series 2.3V High capacity super low resistance type
TM
10 Standard Module DLCAP Module 13.8V 15.8V Module
11 Standard Rack DLCAPTM Rack 210V 105V Rack
 Electric Double Layer Capacitors DLCAP(TM)

ELECTRIC DOUBLE LAYER CAPACITOR Introduction

1. Introduction
Compared to the commonly used rechargable batteries, Electric Double Layer Capacitor (EDLC), which is capable of charge - discharge
with high current, is an excellent energy storage device with its charge - discharge cycle life. In the recent years, with energy issues (reducing
of oil use consumer electric power C02 emission effective utilization of new energy) being emphasized towards loading EDLC with a
@ @ @

completely new application is considered. Also, installation of EDLC in hybrid or fuel vehicle is considered.
Nippon Chemi-Con has strongly pursued towards a product development of an energy conservation low environmental load, within this,
@

EDLC is a representative product which is environmental friendly. We hold and provide several hundred F to large capacity of more than
3100F, holding wide specification, meeting user needs.
In this issue, we will introduce our product "DLCAPTM".

2. EDLC Principal
Ordinary capacitors have a dielectric sandwiched electrode, which when a voltage is applied, dipoles are oriented, thus an electric charge
is stored. EDLC has a phenomenon that electric charges are oriented at close locations to the boundary of the electrolyte and electrodes
(called "electric double-layer"), physically charged (Figure 1). Large activated carbon with large specific surface is used for EDLC
terminals.

(Figure1) EDLC Principal

3. Characteristic
As mentioned above, EDLC differs from rechargable batteries, not causing chemical reaction,
with surface of activated carbon with energy accumulation by ionic physical attachment only, therefore it holds the characteristics stated
below ;
@
With low degradation, multimillion cycles of charge - discharge is capable.
@
With a high output density, rapid (high current) charge - discharge is capable.
@
With a high charge - discharge efficiency, an output efficiency of over 95% with an output density 1kW/kg is obtained.
@
Environmental friendly without using heavy metal for its structure material.
@
High in safety during abnormal time, and no malfunction occurs due to short outer circulation.

4. Structure
Nippon Chemi-Con is developing a cylindrical type and prismatic type DLCAPTM (Photo 1).
Standard structure is made by both pasting a terminal onto the aluminum foil, prismatic type in laminated layer-type, and cylindrical type in
roll-type (Figure 2).
Using a large activated carbon with large specific surface for the terminal, with our original high-densified terminal development technology
the energetic characterized terminal, is excellent with both high volume low resistance.
@

Prismatic type DLCAPTM holds an original collector tab technology and by using our production made high density low resistance terminal,
lowering the products resistance, making high current charge - discharge possible, which will be a product capable for a more high power
use compared to the cylindrical type.

(Photo1) DLCAPTM (Figure2) DLCAPTM Structure

NIPPON CHEMI-CON CORPORATION 1

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.779A / Aug.2006 Electric Double Layer Capacitor

2.5V Standard type

@ With the original electrode process, high energy density implementation is possible
@ Charge/discharge efficiency are higher than in batteries
@ Environment-friendly
@ Suited for electricity storage, battery assistance, short-term backups, etc.

?SPECIFICATIONS
Items Specifications
Operating Temperature -25C to +60C
Rated Voltage 2.5Vdc
Capacitance Tolerance P10% (K) (at 20C)
Temperature Capacitance change [P30% of the initial measured value at 20C
Characteristics Internal Resistance [600% of the value given in the Ratings Tables (at -25C)
Load Life Test After the capacitors are subjected to the rated DC voltage at 60C for 2,000 hours, the following specifications shall be
satisfied when the capacitors are restored to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Table
Bias Humidity Test After the capacitors are subjected to the rated DC voltage at 40C and 90 to 95%RH for 500 hours, the following
specifications shall be satisfied when restoring to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Tables

?STANDARD RATINGS
Rated Voltage Capacitance Case Size F Internal Resistance*
Part No.
[V] [F] fD [mm] L [mm] [mm] [mo]

350 65 11 DDLA2R5LGN351KA65S
35 12.7
630 95 7 DDLA2R5LGN631KA95S
2.5
900 105 5 DDLA2R5LGN901KBA5S
40 17.0
1,400 150 3.5 DDLA2R5LGN142KBF0S
* typical data (at 20C)

?DIMENSIONS [mm]

Terminal type CE331

Sleeve

<Screw specification>
FDP1

FP1

Plus hexagon-headed screw

M5B0.8B10
L+4MAX 6P1
Maximum screw tightening torque:3.23Nm

?PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

D DLA AAA LG N AAA K AAA G

Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 700F:701, 1,400F:142)
Mounting Clamp code (B, C)
Terminal code
Voltage code (ex. 2.3V:2R3, 2.5V:2R5)
Series code
Category
Please refer to "A guide to global code (screw-mount terminal type)"

Special designs are available on requests. Note : The specifications are subject to change without notice

2 1371 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.779A / Aug.2006 Electric Double Layer Capacitor

?Temperature dependance of Capacitance & DCIR

120 1,400

100 1,200

1,000

DDCIR (%)
80
DC (%)

800
60
600
40
400

20 200

0 0
-25 -15 -5 5 15 -25 -15 -5 5 15

Temperature (C) Temperature (C)

?60c Load Life Test

-10
DC (%)

-20

-30
0 500 1,000 1,500 2,000

Time (hrs)

100

80
DDCIR (%)

60

40

20

0
0 500 1,000 1,500 2,000

Time (hrs)

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 1371 3

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.772A / Aug.2006 Electric Double Layer Capacitor

2.5V Energy type

@ With the original electrode process, high energy density implementation is possible
@ Charge/discharge efficiency are higher than in batteries
@ Environment-friendly
@ Suited for electricity storage, battery assistance, short-term backups, etc.

?SPECIFICATIONS
Items Specifications
Operating Temperature -25C to +60C
Rated Voltage 2.5Vdc
Capacitance Tolerance P10% (K) (at 20C)
Temperature Capacitance change [P30% of the initial measured value at 20C
Characteristics Internal Resistance [600% of the value given in the Ratings Tables (at -25C)
Load Life Test After the capacitors are subjected to the rated DC voltage at 60C for 2,000 hours, the following specifications shall be
satisfied when the capacitors are restored to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Table
Bias Humidity Test After the capacitors are subjected to the rated DC voltage at 40C and 90 to 95%RH for 500 hours, the following
specifications shall be satisfied when restoring to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Tables

?STANDARD RATINGS
Rated Voltage Capacitance Case Size F Internal Resistance*
Part No.
[V] [F] fD [mm] L [mm] [mm] [mo]

400 65 40 DDLB2R5LGN401KA65S
35 12.7
740 95 22 DDLB2R5LGN741KA95S
1,100 105 15 DDLB2R5LGN112KBA5S
2.5 40 17.0
1,700 150 10 DDLB2R5LGN172KBF0S
1,700 105 10 DDLB2R5LGN172KCA5S
50 22.4
2,700 150 7 DDLB2R5LGN272KCF0S
* typical data (at 20C)

?DIMENSIONS [mm]

Terminal type CE331

Sleeve

<Screw specification>
FDP1

FP1

Plus hexagon-headed screw

M5B0.8B10
L+4MAX 6P1
Maximum screw tightening torque:3.23Nm

?PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

D DLB AAA LG N AAA K AAA G

Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 700F:701, 1,400F:142)
Mounting Clamp code (B, C)
Terminal code
Voltage code (ex. 2.3V:2R3, 2.5V:2R5)
Series code
Category
Please refer to "A guide to global code (screw-mount terminal type)"

Special designs are available on requests. Note : The specifications are subject to change without notice

4 1373 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.772A / Aug.2006 Electric Double Layer Capacitor

?Temperature dependance of Capacitance & DCIR

120 1,400

100 1,200

1,000

DDCIR (%)
80
DC (%)

800
60
600
40
400

20 200

0 0
-25 -15 -5 5 15 -25 -15 -5 5 15

Temperature (C) Temperature (C)

?60c Load Life Test

-10
DC (%)

-20

-30
0 500 1,000 1,500 2,000

Time (hrs)

100

80
DDCIR (%)

60

40

20

0
0 500 1,000 1,500 2,000

Time (hrs)

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 1373 5

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.773A / Aug.2006 Electric Double Layer Capacitor

2.5V Power type

@ With the original electrode process, high energy density implementation is possible
@ Charge/discharge efficiency are higher than in batteries
@ Environment-friendly
@ Suited for electricity storage, battery assistance, short-term backups, etc.

?SPECIFICATIONS
Items Specifications
Operating Temperature -25C to +60C
Rated Voltage 2.5Vdc
Capacitance Tolerance P10% (K) (at 20C)
Temperature Capacitance change [P30% of the initial measured value at 20C
Characteristics Internal Resistance [600% of the value given in the Ratings Tables (at -25C)
Load Life Test After the capacitors are subjected to the rated DC voltage at 60C for 2,000 hours, the following specifications shall be
satisfied when the capacitors are restored to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Table
Bias Humidity Test After the capacitors are subjected to the rated DC voltage at 40C and 90 to 95%RH for 500 hours, the following
specifications shall be satisfied when restoring to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Tables

?STANDARD RATINGS
Rated Voltage Capacitance Case Size F Internal Resistance*
Part No.
[V] [F] fD [mm] L [mm] [mm] [mo]

350 65 8 DDLC2R5LGN351KA65S
35 12.7
640 95 5 DDLC2R5LGN641KA95S
2.5
950 105 3.5 DDLC2R5LGN951KBA5S
40 17.0
1,400 150 2.5 DDLC2R5LGN142KBF0S
* typical data (at 20C)

?DIMENSIONS [mm]

Terminal type CE331

Sleeve

<Screw specification>
FDP1

FP1

Plus hexagon-headed screw

M5B0.8B10
L+4MAX 6P1
Maximum screw tightening torque:3.23Nm

?PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

D DLC AAA LG N AAA K AAA G

Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 700F:701, 1,400F:142)
Mounting Clamp code (B, C)
Terminal code
Voltage code (ex. 2.3V:2R3, 2.5V:2R5)
Series code
Category
Please refer to "A guide to global code (screw-mount terminal type)"

Special designs are available on requests. Note : The specifications are subject to change without notice

6 1375 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.773A / Aug.2006 Electric Double Layer Capacitor

?Temperature dependance of Capacitance & DCIR

120 800

700
100
600

DDCIR (%)
80
DC (%)

500

60 400

300
40
200
20
100

0 0
-25 -15 -5 5 15 -25 -15 -5 5 15

Temperature (C) Temperature (C)

?60c Load Life Test

-10
DC (%)

-20

-30
0 500 1,000 1,500 2,000

Time (hrs)

100

80
DDCIR (%)

60

40

20

0
0 500 1,000 1,500 2,000

Time (hrs)

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 1375 7

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.774A / Aug.2006 Electric Double Layer Capacitor

2.3V High capacity standard type

@ With the original electrode process, high energy density implementation is possible
@ Charge/discharge efficiency are higher than in batteries
@ Environment-friendly
@ Suited for electricity storage, battery assistance, short-term backups, etc.

?SPECIFICATIONS
Items Specifications
Operating Temperature -25C to +60C
Rated Voltage 2.3Vdc
Capacitance Tolerance P10% (K) (at 20C)
Temperature Capacitance change [P30% of the initial measured value at 20C
Characteristics Internal Resistance [600% of the value given in the Ratings Tables (at -25C)
Load Life Test After the capacitors are subjected to the rated DC voltage at 60C for 2,000 hours, the following specifications shall be
satisfied when the capacitors are restored to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Table
Bias Humidity Test After the capacitors are subjected to the rated DC voltage at 40C and 90 to 95%RH for 500 hours, the following
specifications shall be satisfied when restoring to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Tables

?STANDARD RATINGS
Rated Voltage Capacitance Case Size F Internal Resistance*
Part No.
[V] [F] fD [mm] L [mm] [mm] [mo]

400 65 12 DDMA2R3LGN401KA65S
35 12.7
720 95 7.5 DDMA2R3LGN721KA95S
2.3
1,000 105 5.5 DDMA2R3LGN102KBA5S
40 17.0
1,600 150 4 DDMA2R3LGN162KBF0S
* typical data (at 20C)

?DIMENSIONS [mm]

Terminal type CE331

Sleeve

<Screw specification>
FDP1

FP1

Plus hexagon-headed screw

M5B0.8B10
L+4MAX 6P1
Maximum screw tightening torque:3.23Nm

?PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

D DMA A A A L G N A A A K A A A G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 700F:701, 1,400F:142)
Mounting Clamp code (B, C)
Terminal code
Voltage code (ex. 2.3V:2R3, 2.5V:2R5)
Series code
Category
Please refer to "A guide to global code (screw-mount terminal type)"

Special designs are available on requests. Note : The specifications are subject to change without notice

8 1377 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.774A / Aug.2006 Electric Double Layer Capacitor

?Temperature dependance of Capacitance & DCIR

120 1,400

100 1,200

1,000

DDCIR (%)
80
DC (%)

800
60
600
40
400

20 200

0 0
-25 -15 -5 5 15 -25 -15 -5 5 15

Temperature (C) Temperature (C)

?60c Load Life Test

-10
DC (%)

-20

-30
0 500 1,000 1,500 2,000

Time (hrs)

100

80
DDCIR (%)

60

40

20

0
0 500 1,000 1,500 2,000

Time (hrs)

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 1377 9

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.775A / Aug.2006 Electric Double Layer Capacitor

2.3V High capacity energy type

@ With the original electrode process, high energy density implementation is possible
@ Charge/discharge efficiency are higher than in batteries
@ Environment-friendly
@ Suited for electricity storage, battery assistance, short-term backups, etc.

?SPECIFICATIONS
Items Specifications
Operating Temperature -25C to +60C
Rated Voltage 2.3Vdc
Capacitance Tolerance P10% (K) (at 20C)
Temperature Capacitance change [P30% of the initial measured value at 20C
Characteristics Internal Resistance [600% of the value given in the Ratings Tables (at -25C)
Load Life Test After the capacitors are subjected to the rated DC voltage at 60C for 2,000 hours, the following specifications shall be
satisfied when the capacitors are restored to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Table
Bias Humidity Test After the capacitors are subjected to the rated DC voltage at 40C and 90 to 95%RH for 500 hours, the following
specifications shall be satisfied when restoring to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Tables

?STANDARD RATINGS
Rated Voltage Capacitance Case Size F Internal Resistance*
Part No.
[V] [F] fD [mm] L [mm] [mm] [mo]

500 65 45 DDMB2R3LGN501KA65S
35 12.7
870 95 25 DDMB2R3LGN871KA95S
1,300 105 20 DDMB2R3LGN132KBA5S
2.3 40 17.0
2,000 150 11 DDMB2R3LGN202KBF0S
2,000 105 11 DDMB2R3LGN202KCA5S
50 22.4
3,100 150 7.5 DDMB2R3LGN312KCF0S
* typical data (at 20C)

?DIMENSIONS [mm]

Terminal type CE331

Sleeve

<Screw specification>
FDP1

FP1

Plus hexagon-headed screw

M5B0.8B10
L+4MAX 6P1
Maximum screw tightening torque:3.23Nm

?PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

D DMB A A A L G N A A A K A A A G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 700F:701, 1,400F:142)
Mounting Clamp code (B, C)
Terminal code
Voltage code (ex. 2.3V:2R3, 2.5V:2R5)
Series code
Category
Please refer to "A guide to global code (screw-mount terminal type)"

Special designs are available on requests. Note : The specifications are subject to change without notice

10 1379 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.775A / Aug.2006 Electric Double Layer Capacitor

?Temperature dependance of Capacitance & DCIR

120 1,400

100 1,200

1,000

DDCIR (%)
80
DC (%)

800
60
600
40
400

20 200

0 0
-25 -15 -5 5 15 -25 -15 -5 5 15

Temperature (C) Temperature (C)

?60c Load Life Test

-10
DC (%)

-20

-30
0 500 1,000 1,500 2,000

Time (hrs)

100

80
DDCIR (%)

60

40

20

0
0 500 1,000 1,500 2,000

Time (hrs)

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 1379 11

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.776A / Aug.2006 Electric Double Layer Capacitor

2.3V High capacity power type

@ With the original electrode process, high energy density implementation is possible
@ Charge/discharge efficiency are higher than in batteries
@ Environment-friendly
@ Suited for electricity storage, battery assistance, short-term backups, etc.

?SPECIFICATIONS
Items Specifications
Operating Temperature -25C to +60C
Rated Voltage 2.3Vdc
Capacitance Tolerance P10% (K) (at 20C)
Temperature Capacitance change [P30% of the initial measured value at 20C
Characteristics Internal Resistance [600% of the value given in the Ratings Tables (at -25C)
Load Life Test After the capacitors are subjected to the rated DC voltage at 60C for 2,000 hours, the following specifications shall be
satisfied when the capacitors are restored to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Table
Bias Humidity Test After the capacitors are subjected to the rated DC voltage at 40C and 90 to 95%RH for 500 hours, the following
specifications shall be satisfied when restoring to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Tables

?STANDARD RATINGS
Rated Voltage Capacitance Case Size F Internal Resistance*
Part No.
[V] [F] fD [mm] L [mm] [mm] [mo]

450 65 8.5 DDMC2R3LGN451KA65S

35 12.7
760 95 5.5 DDMC2R3LGN761KA95S
2.3
1,100 105 4 DDMC2R3LGN112KBA5S
40 17.0
1,700 150 2.7 DDMC2R3LGN172KBF0S
* typical data (at 20C)

?DIMENSIONS [mm]

Terminal type CE331

Sleeve

<Screw specification>
FDP1

FP1

Plus hexagon-headed screw

M5B0.8B10
L+4MAX 6P1
Maximum screw tightening torque:3.23Nm

?PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

D DMC A A A L G N A A A K A A A G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 700F:701, 1,400F:142)
Mounting Clamp code (B, C)
Terminal code
Voltage code (ex. 2.3V:2R3, 2.5V:2R5)
Series code
Category
Please refer to "A guide to global code (screw-mount terminal type)"

Special designs are available on requests. Note : The specifications are subject to change without notice

12 1381 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.776A / Aug.2006 Electric Double Layer Capacitor

?Temperature dependance of Capacitance & DCIR

120 800

700
100
600

DDCIR (%)
80
DC (%)

500

60 400

300
40
200
20
100

0 0
-25 -15 -5 5 15 -25 -15 -5 5 15

Temperature (C) Temperature (C)

?60c Load Life Test

-10
DC (%)

-20

-30
0 500 1,000 1,500 2,000

Time (hrs)

100

80
DDCIR (%)

60

40

20

0
0 500 1,000 1,500 2,000

Time (hrs)

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 1381 13

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.778A / Aug.2006 Electric Double Layer Capacitor

2.5V Super low resistance type

@ With the original electrode process, high energy density implementation is possible
@ Charge/discharge efficiency are higher than in batteries
@ Environment-friendly
@ Suited for electricity storage, battery assistance, short-term backups, etc.

?SPECIFICATIONS
Items Specifications
Operating Temperature -30C to +60C
Rated Voltage 2.5Vdc
Capacitance Tolerance P10% (K) (at 20C)
Temperature Capacitance change [P30% of the initial measured value at 20C
Characteristics Internal Resistance [600% of the value given in the Ratings Tables (at -25C)
Load Life Test After the capacitors are subjected to the rated DC voltage at 60C for 2,000 hours, the following specifications shall be
satisfied when the capacitors are restored to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Table
Bias Humidity Test After the capacitors are subjected to the rated DC voltage at 40C and 90 to 95%RH for 500 hours, the following
specifications shall be satisfied when restoring to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Tables

?STANDARD RATINGS
Rated Voltage Capacitance Case Size F F2 Internal Resistance*
Part No.
[V] [F] WbD [mm] L [mm] L2 [mm] [mm] [mm] [mo]

1,800 98 109 0.9 DDSC2R5LGN182K54AS

54×54 27.15 19.5
2,400 128 139 0.7 DDSC2R5LGN242K54BS
2.5
900 98 107 1.8 DDSC2R5LGN901K30AS
54×30 27.4 -
1,200 128 135 1.4 DDSC2R5LGN122K30BS
* typical data (at 20C)

?DIMENSIONS [mm]
Sleeve DP1 DP1

<Screw specification>
Plus hexagon-headed screw
WP1
WP1

F2 F
54B54type M6B1.0B12 54B30type M5B0.8B10
Maximum screw tightening torque :3.23Nm
LP1 F F2

L2P1

?PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

D DSC AAA LG N AAA K AAA G

Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 700F:701, 1,400F:142)
Mounting Clamp code (B, C)
Terminal code
Voltage code (ex. 2.3V:2R3, 2.5V:2R5)
Series code
Category
Please refer to "A guide to global code (screw-mount terminal type)"

Special designs are available on requests. Note : The specifications are subject to change without notice

14 1385 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.778A / Aug.2006 Electric Double Layer Capacitor

?Temperature dependance of Capacitance & DCIR

120 800

700
100
600

DDCIR (%)
80
DC (%)

500

60 400

300
40
200
20
100

0 0
-30 -20 -10 0 10 20 -30 -20 -10 0 10 20

Temperature (C) Temperature (C)

?60c Load Life Test

-10
DC (%)

-20

-30
0 500 1,000 1,500 2,000

Time (hrs)

100

80
DDCIR (%)

60

40

20

0
0 500 1,000 1,500 2,000

Time (hrs)

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 1385 15

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.777A / Aug.2006 Electric Double Layer Capacitor

2.3V High capacity super low resistance

@ With the original electrode process, high energy density implementation is possible
@ Charge/discharge efficiency are higher than in batteries
@ Environment-friendly
@ Suited for electricity storage, battery assistance, short-term backups, etc.

?SPECIFICATIONS
Items Specifications
Operating Temperature -30C to +60C
Rated Voltage 2.3Vdc
Capacitance Tolerance P10% (K) (at 20C)
Temperature Capacitance change [P30% of the initial measured value at 20C
Characteristics Internal Resistance [600% of the value given in the Ratings Tables (at -25C)
Load Life Test After the capacitors are subjected to the rated DC voltage at 60C for 2,000 hours, the following specifications shall be
satisfied when the capacitors are restored to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Table
Bias Humidity Test After the capacitors are subjected to the rated DC voltage at 40C and 90 to 95%RH for 500 hours, the following
specifications shall be satisfied when restoring to 20C.
Capacitance change [P30% of the initial measured value
Internal Resistance [200% of the value given in the Ratings Tables

?STANDARD RATINGS
Rated Voltage Capacitance Case Size F F2 Internal Resistance*
Part No.
[V] [F] WbD [mm] L [mm] L2 [mm] [mm] [mm] [mo]

2,100 98 109 0.9 DDTC2R3LGN212K54AS

54×54 27.15 19.5
2,800 128 139 0.7 DDTC2R3LGN282K54BS
2.3
1,100 98 107 1.8 DDTC2R3LGN112K30AS
54×30 27.4 -
1,400 128 135 1.4 DDTC2R3LGN142K30BS
* typical data (at 20C)

?DIMENSIONS [mm]
Sleeve DP1 DP1

<Screw specification>
Plus hexagon-headed screw
WP1
WP1

F2 F
54B54type M6B1.0B12 54B30type M5B0.8B10
Maximum screw tightening torque :3.23Nm
LP1 F F2

L2P1

?PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

D DTC AAA LG N AAA K AAA G

Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 700F:701, 1,400F:142)
Mounting Clamp code (B, C)
Terminal code
Voltage code (ex. 2.3V:2R3, 2.5V:2R5)
Series code
Category
Please refer to "A guide to global code (screw-mount terminal type)"

Special designs are available on requests. Note : The specifications are subject to change without notice

16 1383 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Engineering Bulletin No.777A / Aug.2006 Electric Double Layer Capacitor

?Temperature dependance of Capacitance & DCIR

120 800

700
100
600

DDCIR (%)
80
DC (%)

500

60 400

300
40
200
20
100

0 0
-30 -20 -10 0 10 20 -30 -20 -10 0 10 20

Temperature (C) Temperature (C)

?60c Load Life Test

-10
DC (%)

-20

-30
0 500 1,000 1,500 2,000

Time (hrs)

100

80
DDCIR (%)

60

40

20

0
0 500 1,000 1,500 2,000

Time (hrs)

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 1383 17

 Electric Double Layer Capacitors DLCAP(TM)

Tentative
Engineering Bulletin No.785A / Oct.2006 Electric Double Layer Capacitor

Electric Double Layer Capacitor

For an easy usage of Electric Double Layer Capacitor DLCAPTM,

we have prepared a standard module.
By connecting several of these modules, composing a higher voltage,
larger volumed module will be possible.

@ Application Examples
Solar energy generation charge
@ Rated 15V 100F (Inner Resistance 38mO)
Wind electric generator buffer
@

Battery assistance
@

Vehicle regenerative energy charge

@

UPS battery alternative

@

@ DLCAP Standard Module

? Features
Voltage balance circuit installed
@

(Up front photo)

Rated 15V 400F (Inner Resistance 6mO)
(Rear photo)
Rated 13.8V 500F (Inner Resistance 44mO)
?Product List
Rated Voltage Capacitance Size [mm] Inner Resistance Weight
Part No.
[V] [F] A B C [mo] [kg]

58 282 37 98 68 0.95 MDLA15R0V050F

15 100 282 37 138 38 1.40 MDL-15R0V100F
233 318 44 177 17 2.40 MDLC15R0V233F
13.8 500 377 54 163 44 3.20 MDMB13R8V500F
150 261 66 132 12 2.30 MDSC15R0V150F
15
400 401 58 162 6 4.16 MDSC15R0V400F

?Environmental Conditions
Item Performance
Operation Temperature[C] -30 to +60
Operation Humidity[%RH] 20 to 90 (non condensing)
Storage Temperature[C] -40 to +60
Storage Humidity[%RH] 15 to 95 (non condensing) * The specifications are subject to change without notice.

@ DLCAP Custom Module Responses

?Information
High voltage application response
@

Lagre volume application response

@

High current application response

@

Proper balance circuit recommendation

@

Uncommon circuit or controlled charge discharge

@

circuit response
Expected life estimation
@

Standard Bank Dimention Outline Drawing

Due to upgrading, this bulletin may change without notice

18 NIPPON CHEMI-CON CORPORATION

 Electric Double Layer Capacitors DLCAP(TM)

Tentative
Engineering Bulletin No.786A / Oct.2006 Electric Double Layer Capacitor

Electric Double Layer Capacitor

@ Rack type for fixed energy storage. ?Application Example

@ Suitable for industrial machine high voltage use. @
Instant low voltage electricity (less than 1 sec) measuring
@ Serieal / Parallel lining of the rack is possible. equipment energy storage use.
@
Regenerative Energy Storage use for cranes, etc.
* By connecting several racks, composing a high voltage high @

volume bank will be possible.

* Forced cooling fan (24 pieces) may be attached as an option.
?Specification Chart
Item Specifications Others
Product Number MDLC210V116F MDLC105V466F
Rated Voltage(Maximum charged voltage) 210 [V] 105 [V]
Electric Capacitance(typ.) 116 [F] 466 [F] 20C Defalt
Direct Inner Resistence(typ.) 32 [mO] 8[mO] 20C Defalt
Dimention 780 B 470 B 1770(H) [mm]
Weight 445 [kg]
Environmental Operation -25K+60 [C] 20K90 [%RH] (non condensing)
Requirements Storage -40K+60 [C] 15K90 [%RH] (non condensing)
Insulation Resistance Over 100 [MO] DC500V 1min
Insulation Voltage Over 2.5 [KV] AC 1min

?Aspect/ Dimention Outline Drawing

Special designs are available on requests. Note : The specifications are subject to change without notice

NIPPON CHEMI-CON CORPORATION 19