Sr.No. Tool Name/EMD/DLW/Part No. Qty.

1. Clamp for lifting Cyl. Head DLW Part No. 14

15610202
2. Lifting arrangement for Head fram DLW Part No. 04
3. Lifter for Bearing cap DLW Part No. 15610524 07
4. Reaming Fixture DLW Part No. 15610299 24
5. Lifter for radiator assly. DLW part No. 15630043 03
6. Cradle for Power pack DLW Part No. 15610573 17
Drg. NO. SK05GM0052
7. Lifting for G Turbocharger DLW Part No. 4
15610147
8. G.M. Loco alternator & Engine alignment drive 4
DLW part No.15630080
9. Sacking tool for Adjusting Accessory DLW Part 08
No.-15610020
10. Guide Pin to line up oil Pan to crank case during 07
Assly.
11. CCrank case line up fixture for oil pan assembly 08
12. Crank case line up fixture (small length 5th) for 5
oil pan assly.
13. Clamp lifting piston linor and head assly. 9
14. Spanner bar to chack flexing of accessory drive 6
gear assly.
15. Hook and clamp for lifting lube oil strainer assly. 7
16. Braket lifter for assly of cam shaft housing 6
17. Lifting drive turbo air duct assly 4
18. LLocating Pad for end crab cyl.Head 11
19. Jack for governer in secter linkage 6
20. Lifter for after cooling con assly 5
21. C –clamp for aux-gen assly 5
22. Mandrel for assly 8
23. Pressing for ½” OD Tube main fram member of 4
crankcase
24. Dowilling fixture for generator 4
25. AAlignment fixture for w/ coupling (Engine) to 5
equipment rack
26. Arrangement for alignment of w/pump 5
27. Steel straight ledge 36” for counter weight 6
 setting
28. Piston ring compressor guide 4
29. Clamp lifting cyl.linor assly 8
30. Clearing tool for reate seal 13
31. Lifter for cooling fan assly 2
32. SSpring depressor cyl.head valen liver 10
33. Acc. Housing alignment gauge 8
34. Cranking tool for GM 10
35. Piston holder DLW 35
36. Engine Turing Fixture 3
37. Eyebolt for lifter turbo 4
38. Gauge with dial indicator for cam shaft drive 6
housing
39. jacking tool for lining Acc. Drive housing 6
40. Point disc used for timing engine 7
41. Insert pressing fixture c/case assly 3
42. WWire holder 13
43. Installer part 4
44. Clamp for lifting idler gear stab shaft 2
45. Alignment gauge to check line up of oil pan 3
46. Hook for lifting acc. Drive housing 6
47. Lifter for aux. gen assly 5
48. Try squre 12” for counter weight setting 5
49. Timing gauge for end of in section at future c/c 8
50. Gauge for injector rack setting 10
51. Tube for crab stand thread 3
52. GGauge for alignment at driving end aux. 6
53. Assly. Fix for connecting rob. Carrier and piston 4
pin
54. Line up indicators gauge to set up at stub shaft 5
from crank shaft & cam shaft
55. Backlash crack gauge on starter & braket assly. 3
56. Arrangement for alignment as R/s w/pump in 6
GM loco
57. Holding fix for crank shaft with crank case 4
58. Line up tooling for engine to compressor applied 2
to shaft
59. Tram for exhaust valve HT 2
60. Master setting gauge for GP001GM 0009 used 5
with stub idlor shaft setting
61. Mounting arrangement flange of dial gauge 7
62. Engine lift device & hooking position 3
63. Ream fix and plug to be used for ream stub shaft 4
to crank case plate
64. Distance gauge idler gear stub and L/S cam shaft 5
65. Alignment gauge and dial indicator for oil pan to 6
c/case
66. Template to crack line up of oil pan and crank 6
case assly. End
67. Wrinch. In jector assly. 8
68. Counter Weight alignment gauge at cam shaft 4
drive end
69. Leak test gauge 11
70. Flat wire brush 25
71. Wire brush for cleaning gearcase 38
72. Hydraulic lash adjuster installer 01
73. Puller Multiple hydraulic lash adjuster 04
74. Box socket wrench w/pump mounting nut 4
75. Valve bridge spring compressor 4
76. Crank over tool 4
77. Crank over tool air motor reaction bar 4
78. Pin vise for holding 03
79. Remover for upper main bearing 03
80. Seal inserter for head fram 3
81. Reamer for test valve 1