BEST WOOD CARVING TOOLS HOW TO DESIGNS

Find the best wood carving tools, guides, tutorials, and more!

Chip Carving: The Top Online Handbook

Something I really like about this method, and everyone reading will probably enjoy as well, is
that you only need two knives to get yourself started, and wood of course.

Today you’ll learn about the tools used for

chip carving as well as, main cutting
Best Seller
techniques, how to grip your knife, common
patterns, and more to help get you started.
Top Recommended Chip Knives

This style of wood carving is used for

creating aesthetic patterns and designs in
wood.

Check Prices on Amazon!

Also read the full review >>

Tools Used for Chip Carving

1. Primary Knife – You will be using this the most as it is used for chipping out most of the
material.

Inspecting the profile of the blade with a magnifying glass could be necessary if the knife has
been used before or if it wasn’t sharpened already when bought. The blade should have no
bevels (the horizontal or vertical slope that looks similar to an edge).

2. Stab Knife – Effectively utilized as a specialty tool for making aesthetic markings.
3. Wood – There’s a number of woods to choose from, but for beginners I’d suggest
basswood since it is the easiest to work with.

Here’s our top recommendations for this style:

BEST WOOD CARVING TOOLS HOW TO DESIGNS

Wayne Barton Chip Carving Knife Set

The durability of this knife is relieving seeing as how other knives in it’s price range tend to be
cheaply made. Most lack in wood density that make the handle comfortable enough to use for
long periods of time.

It comes razor sharp and ready to use.

Things we enjoyed Things we didn’t enjoy

Sturdy knife ✘ Requires honing

Blade isn’t glued in
Dense Wood
Quality Steel
Good knife for price

To add, basswood is the most ideal wood to begin carving with so go grab a 8″ X 10″ panel
to begin by clicking the button below.

Check Prices For Basswood

How Do I Sharpen My Chip Carving Tools?

If there are bevels on either side of your primary, using a sharpening stone to trim them off will
be required before beginning any projects.

I prefer diamond sharpening stones since they are the most diverse with wood carving tools,
this is the one I use:

Sharpening chip carving tools differs slightly Smith’s Arkansas TRI-HONE

than sharpening regular whittling knives. To
shave down the bevels it’s ideal to tip the
blade at a 10-degree angle then rub it back
and forth on the stone.

You’ll want to work both sides of the blade

the same number of times to avoid it being
uneven.
BEST WOOD CARVING TOOLS HOW TO DESIGNS

Check Prices on Amazon!

The 400 grit stone is to help remove the bevels so use this first then use the 1200 grit for
polishing.

Lastly, as far as sharpening goes, complete with a leather strop and honing compound. Be
sure to hone the blade to the tip as this is to remove any small chips, a magnifying glass is
helpful in this situation to be able to see if there are any left.

During the process, be mindful not to break the blade otherwise you must restart all over.

Gripping Positions
Grip positioning is very essential for chip carving. Although there are many determining
factors that can help carve a clean pattern, which I will discuss further into this guide, but here
is the main priority before ever even starting a project:

Perfecting grip positioning

If your grip is off, then your cut is off. If your cut is off, your pattern is off. And if your pattern is
off, well you see where I’m going with this.
 So let’s start with how to hold the primary knife, there are 2 ways:
BEST WOOD CARVING TOOLS HOW TO DESIGNS

• Grip the back part of the handle with your fingers and rest the thumb on the flat facet
that’s on the front side of the handle just under the blade.

Keep thumb on the handle, NOT on the wood otherwise cutting yourself can become
very easy to do!

• The alternative way positions the fingers around the front of the handle and the thumb
rests on the back part of the blade.

Both grip styles should be used cutting at a 65-degree angle.

The stab knife is meant for making aesthetic “stabs” into the wood not necessarily meant for
chipping out material.

• Puncture the wood with the knife holding it perpendicular to the work piece. Begin to tilt
the handle forward while the blade holds the same position. This technique helps create
this cut:
BEST WOOD CARVING TOOLS HOW TO DESIGNS

3 Main Cutting Techniques

Chip carving patterns are found from these shapes. After getting familiar with them, it only
becomes a matter of designing patterns and carving them.

• Three Corner Chip – If you couldn’t already tell from the name this is a three part cut
which gives you a triangle shaped chip. ***PICTURE***

Set the wood on your lap to make it easier to turn the work piece and achieve optimal angles.
If the wood is too big set it on a table. The two primary knife grips explained earlier are utilized
for this technique.

Let’s begin with the first part:

1. Plunge Cut – Start by piercing straight down into the wood with the point of your primary
knife at a 65-degree angle. Once the point of your knife reaches the desired depth, slide
the blade out of the work piece.
 2. Slicing Cut – Turn your work piece to a sufficient angle. Start the point of the knife
BEST WOOD
where CARVING
your last cutTOOLS
HOW TO
left off, start shallow with the cut on the baseline and go deeper to
DESIGNS

reach the point of depth the plunge cut created then draw the blade out slowly.

• Slicing Cut – Finish by doing another slicing cut. Begin where the second cut left off
while making the shallow cut down to the point of depth and slide the blade out. The
material should pop out with it.

Do not pry out material if your cut does not bring it out, you will run the risk of breaking
off the tip of your blade. Instead try cutting it again, except go deeper with the cut.

• Straight Lines – Keep a firm grip of the item you are carving while making these cuts to
provide stability. When finishing a stop cut, tip the knife up so your blade doesn’t surpass
the designated mark.

Something that has helped me with cutting clean straight lines is to look ahead of the
blade and anticipate where it should go, NOT looking at the blade.

• Curved Lines – The blade is consistently kept at a 65-degree angle and because of this
the wider the shapes makes for a deeper cut.

Transferring Patterns to Wood

Once the basic cutting styles have been perfected, you’ll probably be wanting to create
original or more intricate designs.
 There’s a key thing everyone misses to make things 100% easier when transferring any
BEST WOOD
pattern CARVING TOOLS
to wood:
HOW TO DESIGNS

Sand it down

Rough surfaces for chip carving are very annoying, you’ll soon find out, since it can cause
hesitation with your cuts and is also impossible to draw straight lines on. I use a 32 grit
sandpaper which also is useful for taking pencil sketches out when the project is finished.

How Do I Transfer a Design I Want to Carve on to Wood?

1. Pattern Tracing with Graphite Paper

This method is best with smaller patterns and also good to use on oddly shaped woods, as
opposed to a regular square shape.

Print a copy out of the design so you can use graphite paper to trace it onto the wood.
Center the pattern to your preference then tape it onto the edge from one side. Next you will
slide the graphite paper underneath the printed copy.

Be sure to use a ruler or a different straight edged object and a hard pencil to maintain
accuracy while marking along the edge.

Once cutting is complete just erase the traced lines, using sandpaper helps.

Check Prices for Graphite Paper

2. Graphing onto The Wood

Practically all of chip carving is geometrical patterns which makes graphing an ideal and
popular method.

Mark the grid to the board with a small t-square, a ruler, and a hard pencil. Keep in mind that
the size of each square unit determines the size of the final design.

Your completed project will only be as precise as your pencil marking so take your time and
be patient while creating the grid.

F.A.Q.
What sharpening stone should I use to shave the bevels off the primary knife?
 I use the Smith’s TRI-6 Arkansas. It has 3 stones which rotate around pretty easily. Comes
BEST
withWOOD CARVING
400 grit, TOOLS
600 grit, and
HOW TO
1200 grit stones that offer any needs your knives will need from
DESIGNS

shaving off steel matter to honing a finer edge retention.

Best Wood Carving Set For

All Wood

How To Make Woodworking

Projects Profitable

586+ Options for Beginner

Woodworking Projects

Best Woodworking Clamps

For Common Tasks

Best Sandpaper for Wood

Best Rotary Tool For Wood

Carving
BEST WOOD CARVING TOOLS HOW TO DESIGNS

RECENT REVIEWS
Search this website
Best Wood Carving Set For All Wood August 31,
2019
 How To Make Woodworking Projects Profitable
BEST WOOD CARVING TOOLS May 27, 2019 HOW TO DESIGNS

586+ Options for Beginner Woodworking

Projects May 19, 2019

Best Woodworking Clamps For Common Tasks

May 7, 2019

Best Sandpaper for Wood April 10, 2019

Copyright © 2019

About Us Contact Us Disclaimer