Scribd
Upload
478 views3 pages

VE1A Station Maintenance Guide

The document provides guidelines for maintaining station VE1A (C4). It states that dirt and moisture often cause errors E-3 or E-5. The guidelines instruct cleaning insulators and cables, using alcohol and avoiding solvents. It outlines 5 steps for cleaning parts like the electrode cartridge, inside the station, insulators and electrodes to ensure proper electrical contact and air flow.

Uploaded by

aless2056
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
478 views3 pages

VE1A Station Maintenance Guide

The document provides guidelines for maintaining station VE1A (C4). It states that dirt and moisture often cause errors E-3 or E-5. The guidelines instruct cleaning insulators and cables, using alcohol and avoiding solvents. It outlines 5 steps for cleaning parts like the electrode cartridge, inside the station, insulators and electrodes to ensure proper electrical contact and air flow.

Uploaded by

aless2056
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Fabriksvej 11

DK-6000 Kolding Denmark


Tel. +45 76 300 333 A/S reg.no 106.139
Fax +45 76 300 334 VAT-no. DK 78756616

Maintenance of station
Guidelines for VE1A (C4) Station
In most occasions Dirt and moist causes error E-3 or E-5.
It is very important to clean the insulators and cable shown on the pictures on the following pages.

Here are a few pointers to go by.


· When cleaning use alcohol, NO solvents may be used as it will cause damage on parts.
Aim to get the insulators as clean as the one shown on the following pictures.
· You should clean the station according to the maintenance chapter in your manual.

Step 1
Take out electrode cartridge as shown in the picture below

Page 1 of 3

WWW.VETAPHONE.COM > MARKET LEADER WITH MORE THAN 60 YEARS EXPERIENCE


Fabriksvej 11
DK-6000 Kolding Denmark
Tel. +45 76 300 333 A/S reg.no 106.139
Fax +45 76 300 334 VAT-no. DK 78756616

Step 2
View of inside the station

The white insulator should be cleaned.


If any burn marks then replace part.

Connector Pin.
Check for good electrical
contact.

High Voltage Cable.


Clean grey insulating area of the cable.

Step 3
View of insulator in electrode cartridge

Clean the HP contact + insulator. If any burn


marks on insulator then replace it.
Connector clips.
Check for good
electrical contact.

Wires.
Check wires are
mounted as shown.
Always keep short

Page 2 of 3

WWW.VETAPHONE.COM > MARKET LEADER WITH MORE THAN 60 YEARS EXPERIENCE


Fabriksvej 11
DK-6000 Kolding Denmark
Tel. +45 76 300 333 A/S reg.no 106.139
Fax +45 76 300 334 VAT-no. DK 78756616

Step 4
Clean the electrodes. Especially between the electrodes to secure the air exhaust between the
electrodes.

Step 5
Clean the white electrode holder on all 4 electrode and on both the right and left side. As shown in
the picture below.

If you have any doubts or questions what to do or look for please do not hesitate to contact us again.

Best regards

Support Department

Support: +45 76 300 335


Vetaphone: +45 76 300 333
E-mail: support@vetaphone.com
Web: www.vetaphone.com

Page 3 of 3

WWW.VETAPHONE.COM > MARKET LEADER WITH MORE THAN 60 YEARS EXPERIENCE

You might also like