96M13107

Precautions on Proper Use

• Do not use a voltage other than 5VDC with the SR-700 Series. Doing so
may lead to damage on the unit.

ULTRA-COMPACT Code Reader • When using the dedicated communication units (N-R2/R4/UB/L1, or DV-90
Series), use a power supply within the appropriate range for each unit.

SR-700 Series
• Be sure to turn the power off to devices attached to the SR-700 Series
when you plug or unplug the cables. Failure to do so may cause damage
to the SR-700 Series.

Instruction manual • Do not disassemble or modify the SR-700 Series. Doing so may lead to
damage on the unit.
• Keep the cables away from high-tension cables or power sources.
Otherwise, noise could cause malfunctions or accidents.
Read this instruction manual before using the product in order to achieve • The SR-700 Series is a precision instrument.
Do not apply shock to the instrument or drop
maximum performance. it. Be especially careful when transporting or
Keep this instruction manual in a safe place after reading it so that it can be installing the unit.
used at any time.

„ Symbols
The following symbols alert you to important messages. Be sure to read
these messages carefully. NOTICE
• Do not hold the SR eries by its cable. The
It indicates a hazardous situation which, if not avoided, will result in death or units may become damaged if they strike
DANGER
serious injury. each other.

It indicates a hazardous situation which, if not avoided, could result in death

WARNING
or serious injury.
It indicates a hazardous situation which, if not avoided, could result in minor
CAUTION
or moderate injury.
It indicates a situation which, if not avoided, could result in product damage
NOTICE
as well as property damage.

Important It indicates cautions and limitations that must be followed during operation.

Point It indicates additional information on proper operation.

• Do not allow water, oil, dust, or other foreign substances to stick to the
Reference It indicates tips for better understanding or useful information. scanner. This may cause read errors. Use a soft, dry cloth to wipe any
substances from the scanner. (Do not use a cloth dipped in alcohol or
other cleaning substance.)
indicates the reference pages in this manual or the reference pages in separate manuals.

Safety Information for SR-700 Series Precautions on Regulations and Standards

„ General Precautions „ CE Marking
• Do not use this product for the purpose to protect a human body or a part Keyence Corporation has confirmed that this product complies with the
of human body. essential requirements of the applicable EC Directive, based on the
• This product is not intended for use as explosion-proof product. Do not
WARNING
following specifications. Be sure to consider the following specifications
use this product in a hazardous location and/or potentially explosive
atmosphere. when using this product in the Member State of European Union.
• Be sure to check that the SR-700 Series performs properly before starting z EMC Directive (2004/108/EC)
the work or operation.
• If the SR-700 Series malfunctions, take adequate safety precautions to • Applicable standards EMI : EN61326-1, Class A
CAUTION
prevent various types of damage.
EMS : EN61326-1
• Do not use the SR-700 Series in a manner not specified herein. It may
result in fire, electric shock or malfunction. • This product is intended to be used in an industrial electromagnetic
• It should be noted that functions and performances will not be guaranteed environment.
if the SR-700 Series is used in any way not specified or described in the Remarks:
product specifications or it is modified.
• When the SR-700 Series is used in combination with other devices, These specifications do not give any guarantee that the end-product with
NOTICE
functions and performance may be degraded, depending on the operating this product incorporated complies with the essential requirements of
conditions and environment. EMC Directive. The manufacturer of the end-product is solely responsible
• If the equipment is used in a manner not specified by the manufacturer.
the protection provided by the equipment may be impaired. for the compliance on the end-product itself according to EMC Directive.
z Low-voltage Directive (2006/95/EC)
Safety precautions on Laser product • Applicable Standard EN60825-1,
Class 1 Laser Product
The SR-700 Series ULTRA-COMPACT Code Reader uses a visible EN62471
semiconductor laser, with a wavelength of 660 nm, as a Laser pointer for
adjusting the reading position. „ CSA Certificate
„ Laser Pointer Specifications This product complies with the following CSA and UL standards and has
been certified by CSA.
Wavelength 660 nm • Applicable standards: CAN/CSA C22.2 No.61010-1
Output 60 μW UL61010-1
Be sure to consider the following specifications when using this product as a
Pulse duration 20 0μs
product certified by CSA.
Class 1 Laser Product
Laser class • Overvoltage category
(IEC60825-1:2007, FDA(CDRH) Part 1040.10*)
• Use this product under pollution degree 2.
* The laser classification for FDA(CDRH) is implemented based on • Use this product at the altitude of 2000 m or less.
IEC60825-1 in accordance with the requirements of Laser Notice No.50. • Indoor use only.
• When using this product, use the following power supply.
Follow the instructions mentioned in this manual. Otherwise, injury to the •CSA or UL certified power supply that provides Class 2 output as defined
human body (eyes and skin) may result. in the CEC (Canadian Electrical Code) and NFPA79 (NEC: National
• Use of controls or adjustments or performance of procedures other than
Electrical Code), or
those specified herein may result in hazardous radiation exposure. •CSA or UL certified power supply that has been evaluated as a Limited
• Do not disassemble this product. The laser radiation emission from this Power Source as defined in CAN/CSA-C22.2 No. 60950-1/UL60950-1.
WARNING
product is not automatically stopped when it is disassembled.
Precautions on Class 1 Laser Product
• Do not stare into the direct or specularly reflected beam.

1 E SR-700-IM
 FDA (CDRH) Regulations Part Names and Functions
This product complies with the following FDA (CDRH) regulations.
• FDA(CDRH) Part 1040.10, Class 1 Laser Product
The laser classification for FDA(CDRH) is implemented based on IEC60825-
(8) IN LED
1 in accordance with the requirements of Laser Notice No.50.

 FCC Regulations
This product complies with the following FCC EMI regulations.
• FCC Part 15 Subpart B, Class A Digital Device

 IC (Industry Canada) Regulations

This product complies with the following IC EMI regulations.
• ICES-003, Class A Digital Apparatus

 Radio Waves Act in South Korea (7) Multiple LED (11) TEST switch
Class A Equipment indicator
(9) OK/NG/ERR LED (10) TUNE switch
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Note: This caution is effective for the Korean Radio Act only. (1) Scanner
A 급 기기 ( 업무용 방송통신기자재 )
이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는 사용자는 이 점을 (2) Cable
주의하시기 바라며 , 가정외의 지역에서 사용하는 것을 목적으로 합 니다 .

Checking the Package Contents

Insulating spacer x 2 Main unit (SR-700HA/SR-700/SR-710)

Washer x 2

(3) Connector
(round connector)

Installation screws (M3) x 2

(6) Cable holder

(5) USB connector cap

(4) USB connector

Name Function
(1) Scanner Reads 2D codes and barcodes.
(2) Cable Cable length is 1.8 m.
Connects to the power supply and communication unit
Connector
(3) (N-R2/UB/R4/L1). The connector can be used for serial
(Round connector)
communications with external devices.
Connects to a PC to change settings with AutoID Network
(4) USB Connector Navigator. The connector is type A. Cable length is 130 mm
from the section where the cable splits.
When the USB connector is not in use, place the cap on the
(5) USB connector cap connector to prevent the entry of dust and contact with
Mounting bracket x 1 Instruction Manual surrounding metal objects.
When the USB connector is not in use, place the USB cable
(6) Cable holder
in the cable holder so that it does not move around.
96M13107
Precautions on Proper Use

• Do not use a voltage other than 5VDC with the SR Series. Doing so may
lead to damage on the unit.
• When using the dedicated communication units (NX-50CL, N-R2/R4/UB/
ULTRA-COMPACT Fixed Mount Code Reader L1, or DV-90 Series), use a power supply within the appropriate range for
each unit.
SR-700 Series • Be sure to turn the power off to devices attached to the SR Series when
you plug or unplug the cables. Failure to do so may cause damage to the
SR Series.
Instruction manual • Do not disassemble or modify the SR Series. Doing so may lead to
damage on the unit.
• Keep the cables away from high-tension cables or power sources.
Read this instruction manual before using the product in order to achieve Otherwise, noise could cause malfunctions or accidents.

Displays the operation status including the bank number

• The SR Series is a precision instrument. Do
maximum performance. not apply shock to the instrument or drop it.
Keep this instruction manual in a safe place after reading it so that it can be Be especially careful when transporting or
used at any time. installing the unit.

„ Symbols
The following symbols alert you to important messages. Be sure to read
these messages carefully. NOTICE
• Do not hold the SR eries by its cable. The

(7) Multiple LED indicator upon successful decoding, reading stability and operation
It indicates a hazardous situation which, if not avoided, will result in death or
DANGER units may become damaged if they strike
serious injury.
each other.
It indicates a hazardous situation which, if not avoided, could result in death
WARNING
or serious injury.
It indicates a hazardous situation which, if not avoided, could result in minor
CAUTION
or moderate injury.
It indicates a situation which, if not avoided, could result in product damage
NOTICE
as well as property damage.

Important It indicates cautions and limitations that must be followed during operation.

mode.
Point It indicates additional information on proper operation.

Reference It indicates tips for better understanding or useful information. • Do not allow water, oil, dust, or other foreign substances to stick to the
scanner. This may cause read errors. Use a soft, dry cloth to wipe any
substances from the scanner. (Do not use a cloth dipped in alcohol or
indicates the reference pages in this manual or the reference pages in separate manuals. other cleaning substance.)

Safety Information for SR-700 Series

Precautions on Regulations and Standards
„ General Precautions
„ CE Marking
• Do not use this product for the purpose to protect a human body or a part

Lights up when an input terminal is on.

of human body. Keyence Corporation has confirmed that this product complies with the
WARNING • This product is not intended for use as explosion-proof product. Do not essential requirements of the applicable EC Directive, based on the
use this product in a hazardous location and/or potentially explosive following specifications. Be sure to consider the following specifications
atmosphere.
when using this product in the Member State of European Union.
• Be sure to check that the SR-700 Series performs properly before starting
z EMC Directive (2004/108/EC)

(8) IN LED
the work or operation.
• If the SR-700 Series malfunctions, take adequate safety precautions to
CAUTION
prevent various types of damage. • Applicable standards EMI : EN61326-1, Class A
• Do not use the SR-700 Series in a manner not specified herein. It may EMS : EN61326-1
result in fire, electric shock or malfunction.
Remarks:
• It should be noted that functions and performances will not be guaranteed
These specifications do not give any guarantee that the end-product with

(Default settings: Displays the Input terminal 1 state)

if the SR-700 Series is used in any way not specified or described in the
NOTICE
product specifications or it is modified. this product incorporated complies with the essential requirements of
• When the SR-700 Series is used in combination with other devices, EMC Directive. The manufacturer of the end-product is solely responsible
functions and performance may be degraded, depending on the operating
conditions and environment. for the compliance on the end-product itself according to EMC Directive.
z Low-voltage Directive (2006/95/EC)
Safety precautions on Laser product • Applicable Standard EN60825-1,
Class 1 Laser Product
The SR-700 Series ULTRA-COMPACT Fixed Mount Code Reader uses a visible EN62471
semiconductor laser, with a wavelength of 660 nm, as a Laser pointer for
adjusting the reading position. „ CSA Certificate
„ Laser Pointer Specifications This product complies with the following CSA and UL standards and has

• Lights green when a OK signal is output.

been certified by CSA.
Wavelength 660 nm • Applicable standards: CAN/CSA C22.2 No.61010-1
Output 60 PW UL61010-1
Be sure to consider the following specifications when using this product as a
Pulse duration 20 0Ps
product certified by CSA.
Class 1 Laser Product
Laser class • Overvoltage category
(IEC60825-1:2007, FDA(CDRH) Part 1040.10*)
• Use this product under pollution degree 2.
* The laser classification for FDA(CDRH) is implemented based on • Use this product at the altitude of 2000 m or less.
IEC60825-1 in accordance with the requirements of Laser Notice No.50. • Indoor use only.
• When using this product, use the following power supply.

(9) OK/NG/ERR LED • Lights orange when an NG signal is output.

Follow the instructions mentioned in this manual. Otherwise, injury to the •CSA or UL certified power supply that provides Class 2 output as defined
human body (eyes and skin) may result. in the CEC (Canadian Electrical Code) and NFPA79 (NEC: National
• Use of controls or adjustments or performance of procedures other than
Electrical Code), or
those specified herein may result in hazardous radiation exposure. •CSA or UL certified power supply that has been evaluated as a Limited
• Do not disassemble this product. The laser radiation emission from this Power Source as defined in CAN/CSA-C22.2 No. 60950-1/UL60950-1.
WARNING
product is not automatically stopped when it is disassembled.
Precautions on Class 1 Laser Product • Either PoE or 24V power supply shall be used.
• Do not stare into the direct or specularly reflected beam. • The symbol on the product means "Direct current".

• Lights red when an ERROR signal is output.

1 E SR-700-IM

Use this switch to perform the following operations. Refer to

the user manual for more details.
• Turn on the laser pointer for reading position adjustment
• Display registered parameter banks
(10) TUNE switch
(Up to10 banks can be registered.)
• Start parameter tuning
• Read all of the program codes
• Reset errors
Use this switch to perform the following operations. Refer to
the user manual for more details.
• Start and stop test mode
(11) TEST switch
• Run 1 reading operation
• Fix the communication settings to the default values when
sending and receiving the settings

E SR-700-IM 2
 Connection and Wiring Method  Input terminal 1 and Input terminal 2 wiring
These are non-voltage inputs. Connect relay contacts or NPN open collector
 Connection to the communication unit outputs.
Connect the connector to the communication • The TIMING and PRESET inputs are non-voltage inputs.
unit (N-R2/UB/R4/L1).
Refer to the communication unit instruction
manual for more details.
4.7kΩ
220Ω

Internal circuit
10kΩ IN
6,10 With or
without
12 contacts
GND
DC5V

 Connector pin alignment • TIMING (Input terminal 1) is input to initiate the 2D code and barcode
reading.
1 2
• PRESET (Input terminal 2) is input to preset (register) the 2D code and
RP17-13PA-12PC plug (male)
3 4 5 6
barcode data on the SR-700 Series.
Made by Hirose Electric Co., Ltd.
7 8 9 10
 Output terminal 1, Output terminal 2, Output terminal 3
11 12
and Output terminal 4 wiring
These are NPN open collector outputs.
Signal
Pin no. Wire color Signal name Description
direction
Output terminal 1
1 Transparent OUT1 (Default value: Output

Internal circuit
OK output) 4.7kΩ OUT
1, 2, Load
Output terminal 2 5, 9
2 Gray OUT2 (Default value: Output 47kΩ 33V
NG/ERROR output) 12
GND +
3 Purple TxD RS-232C send Output
4 Blue CTS RS-232C send OK Input
Output terminal 4
5 Lt. blue OUT4 (Default value: Output * Rated load: 24VDC (30mA) or less
BUSY output)
Input terminal 2 • OK (Output terminal 1) is output for a successful reading when a check
6 Yellow green IN2 (Default value: Input against preset data is successful.
PRESET input)
• NG/ERROR output (Output terminal 2) is output for an unsuccessful
7 Brown RxD RS-232C receive Input
reading when a check against preset data fails.
8 Pink RTS RS-232C receive OK Output
• ERROR (Output terminal 3) is output for an unsuccessful reading.
Output terminal 3
9 Orange OUT3 (Default value: Output
• BUSY (Output terminal 4) is output when preset data registration has been
ERROR output) completed and internal processing is taking place.
Input terminal 1 When BUSY is output, TIMING (Input terminal 1) cannot be input.
10 Yellow IN1 (Default value: Input
TIMING input)  RS-232C wiring
11 Red 5V 5 V Power –
Use the following wiring when connecting to a PC or a PLC.
12 Black GND (SG) Power GND/Signal GND –

* The shielded wire is connected to a signal ground. SR-700 Series PC, PLC

It is possible to change the functions of the input terminals and output TxD 3 2 RxD(RD)
terminals. Refer to the user's manual for making these changes.
CTS 4 7 RTS(RS)
 Connecting the power RxD 7 3 TxD(SD)

RTS 8 8 CTS(CS)

GND 12 5 GND(SG)

+5V 11 +5V 11 4 DTR(ER)

+

5 VDC
GND 12 Round 6 DSR(DR)
connector
12-pin + D-sub 9-pin
(female) (female)
#4-40 screw

• Do not use a reverse connection for the power supply. Doing so may
damage the unit.
NOTICE
• Use a stable power supply that is 5 VDC +5%, -10%.
Using a power supply that exceeds this range may damage the unit.

3 E SR-700-IM
 Installing the SR-700 Series Mounting the SR-700 Series

Install the SR-700 Series as shown below to ensure reading stability.

 Using the included mounting bracket
 Installation angle 1 Attach the SR-700 Series to the mounting bracket.
The scanner of the SR-700 Series should be positioned at an angle of 15° in
Secure the mounting bracket with the included M3 screws.
relation to the 2D code or barcode surface when carrying out reading.

Reading distance Mounting Included

bracket installation screws
M3 x2

15°
Mounting
bracket

Reading distance

Point Do not position the scanner to face directly at 2D codes or barcodes. Doing
so may cause instability in reading due to mirror reflection.
2 Secure the mounting bracket to the device.
Secure the mounting bracket to the device using the installation screws,
purchased separately, with the included insulating spacers and washers.
The installation screws should be at least 3.7 mm (thickness of the
bracket, washer, etc.) + 3 mm long.
20° or more

15° or more
Washer
Insulating
spacer
Installation
screw (M4)
 Adjusting the installation position and distance
1 Press the TUNE switch on the SR-700 Series. The laser pointer will
emit a laser beam.
Adjust the installation position and distance so that the laser pointer
intersection point and the center of the barcode line up.

The distance where the left

and right laser beams
• Make sure to attach the included insulating spacers to prevent excessive
intersect is the optimal NOTICE noise from the device.
reading distance. • Reading errors may occur if the insulating spacers are not attached.
Adjust the laser pointer's Focal
distance
intersection point so that it
lies directly in the middle
of the 2D code or the
barcode.

Refer to the user's manual for tuning and confirming reading stability.
• The reading distance and angle differ depending on conditions such as
the size and the print quality of the 2D code or the barcode. Carry out
reading tests using the 2D code or barcode to be used and make
adjustments.

E SR-700-IM 4
 Attaching directly to the device  Mounting bracket
Secure the SR-700 Series with screws (M3). * An insulating sheet is affixed to the bottom surface of the mounting
bracket. Do not remove the sheet.
Point The installation screws, purchased separately, should not be any longer than Screw hole size 2-(R2.65)
the length of the plate thickness + 4 mm. R1.5 R18 7 C1
40°
2-M4

40°

18.5
27.5
Installation screws (M3)
φ5.3
18
5.3

32
3.5 24.3
1.5 0.7 0.7 2-R1.5

3.5
8-(R1.65)

4-3.3
33
60.8
5°
1.
°±
90
• Use insulating material when installing the SR-700 Series to prevent
NOTICE excessive noise from the device.
• Reading errors may occur if the insulating material is not attached. 6

0.7

6
Dimensions

 Main unit (SR-700/710/700HA)

(27.8) 24
2-M3
Depth 4 mm 3.5 24.3 13.2 Center of scanner
3.5

18.5
(36.5)

33

40

φ5
Minimum bend R10
3.8

9.3 11

32

Cable length 1800

Cable length 200

53
21

Thickness 13
Cable length 130

5 E SR-700-IM
 Specifications WARRANTIES AND DISCLAIMERS
(1) KEYENCE warrants the Products to be free of defects in materials and
Model SR-700HA SR-700 SR-710 workmanship for a period of one (1) year from the date of shipment. If any
High models or samples were shown to Buyer, such models or samples were used
Type Short-range Mid-range
resolution merely to illustrate the general type and quality of the Products and not to
Light source Visible semiconductor laser (660 nm) represent that the Products would necessarily conform to said models or
Output 60 μW samples. Any Products found to be defective must be shipped to KEYENCE
Laser pointer Pulse width with all shipping costs paid by Buyer or offered to KEYENCE for inspection and
200 μs
examination. Upon examination by KEYENCE, KEYENCE, at its sole option,
Class 1
Laser class will refund the purchase price of, or repair or replace at no charge any Products
(IEC60825-1, FDA CDRH Part 1040.10)
found to be defective. This warranty does not apply to any defects resulting
Light Light source High intensity red LED
from any action of Buyer, including but not limited to improper installation,
QR, MicroQR, DataMatrix,
improper interfacing, improper repair, unauthorized modification, misapplication
2D Code GS1 DataMatrix, PDF417, Micro PDF417,
and mishandling, such as exposure to excessive current, heat, coldness,
GS1 Composite (CC-A, CC-B, CC-C)
moisture, vibration or outdoors air. Components which wear are not warranted.
Code 39, ITF,
(2) KEYENCE is pleased to offer suggestions on the use of its various Products.
2of5 (Industrial 2of5),
Supported COOP 2of5, NW-7 (Codabar), They are only suggestions, and it is Buyer's responsibility to ascertain the
code Code 128, GS1-128, fitness of the Products for Buyer’s intended use. KEYENCE will not be
Barcode *1 GS1 DataBar, Code 93, responsible for any damages that may result from the use of the Products.
JAN/EAN/UPC, (3) The Products and any samples ("Products/Samples") supplied to Buyer are not
Trioptic Code 39, to be used internally in humans, for human transportation, as safety devices or
CODE39 FullASCII, fail-safe systems, unless their written specifications state otherwise. Should any
Pharmacode
Products/Samples be used in such a manner or misused in any way,
Reading Focal distance 38 mm 60 mm 100 mm KEYENCE assumes no responsibility, and additionally Buyer will indemnify
Minimum 2D Code 0.082 mm 0.127 mm 0.19 mm KEYENCE and hold KEYENCE harmless from any liability or damage
resolution Barcode - 0.127 mm 0.127 mm whatsoever arising out of any misuse of the Products/Samples.
22 to 50 mm 40 to 80 mm 45 to 165 mm (4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE
2D Code (Cell size= (Cell size= (Cell size= PROVIDED WITH NO OTHER WARRANTIES WHATSOEVER. ALL
Reading 0.25 mm) 0.5 mm)
0.25 mm) EXPRESS, IMPLIED, AND STATUTORY WARRANTIES, INCLUDING,
distance
30 to 100 mm 45 to 195 mm WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY,
(typical
(Narrow bar (Narrow bar FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF
examples) Barcode -
width width
PROPRIETARY RIGHTS, ARE EXPRESSLY DISCLAIMED.
= 0.33 mm) = 0.5 mm)
IN NO EVENT SHALL KEYENCE AND ITS AFFILIATED ENTITIES BE
Reading view range 26 mm x 42 mm x 70 mm x LIABLE TO ANY PERSON OR ENTITY FOR ANY DIRECT, INDIRECT,
(focal distance) 17 mm 27 mm 45 mm
INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES
Control input 2 non-voltage inputs (IN1, IN2) (INCLUDING, WITHOUT LIMITATION, ANY DAMAGES RESULTING FROM
4 NPN open collector outputs (OUT1 to OUT4) LOSS OF USE, BUSINESS INTERRUPTION, LOSS OF INFORMATION,
30 mA max. (24 V or less) LOSS OR INACCURACY OF DATA, LOSS OF PROFITS, LOSS OF
Control output
ON: Residual voltage 0.8 V or less,
SAVINGS, THE COST OF PROCUREMENT OF SUBSTITUTED GOODS,
OFF: leakage current 0.1 mA or less
SERVICES OR TECHNOLOGIES, OR FOR ANY MATTER ARISING OUT OF
Communicati
RS-232C standards OR IN CONNECTION WITH THE USE OR INABILITY TO USE THE
on method
PRODUCTS, EVEN IF KEYENCE OR ONE OF ITS AFFILIATED ENTITIES
Transmission
9600, 19200, 38400, 57600, 115200 bps WAS ADVISED OF A POSSIBLE THIRD PARTY’S CLAIM FOR DAMAGES
speed
OR ANY OTHER CLAIM AGAINST BUYER. In some jurisdictions, some of the
Input/output Synchronizati
Asynchronous foregoing warranty disclaimers or damage limitations may not apply.
on method
RS-232C Supported
No-protocol, MC Protocol, SYSWAY, KVSTUDIO
protocol BUYER'S TRANSFER OBLIGATIONS:
Data bit If the Products/Samples purchased by Buyer are to be resold or delivered to a
7/8 bits
length third party, Buyer must provide such third party with a copy of this document, all
Stop bit specifications, manuals, catalogs, leaflets and written information provided to
1/2 bits
length Buyer pertaining to the Products/Samples.
Parity check None/Even/Odd E 1101-3
USB Full-speed USB 2.0 interface
Enclosure rating IP65
Ambient temperature 0 to +45°C
Storage temperature -10 to +50°C
Relative humidity 35 to 95% RH (No condensation)
Environment
resistance Sunlight: 10,000lx, incandescent lamp 6,000lx,
Ambient luminance
fluorescent lamp: 2,000lx
Operating environment Location without dust or corrosive gas
10 to 55 Hz: double amplitude 1.5 mm in the X, Y
Vibration
and Z directions. 3 hours respectively.
Power supply voltage 5 VDC +5%, -10%
Rating
Current consumption 630 mA or less
Weight Approx. 160 g (including the cable)

*1 Barcodes fitted into the visual field range in size can be read.

Copyright (c) 2014 KEYENCE CORPORATION. All rights reserved.

E SR-700-IM 6 13107E 1084-1 96M13107 Printed in Japan