MATERIAL SAFETY DATA SHEET
SECTION 1: PRODUCT IDENTIFICATION
MANUFACTURERS ADDRESS : MODERN SAK FACTORY FOR POWDER PAINT
RIYADH, SAUDI ARABIA
MFG TELEPHONE NUMBER : 00966 – 1 - 8102849
CHEMICAL NAME OF FAMILY : EPOXY POLYESTER / PURE POLYESTER /
PURE EPOXY
FORMULA : NOT APPLICABLE
TRADE NAME : SAK Coat
SECTION 2: HAZARDOUS INGREDIENTS
Common (NA) Chemical Name Approx. TLV TWA 10.00 MG/CU M
Weight TLS STEL NOT ESTAB
CAS: 13463-67-7 TITANIUM DIOXIDE Up to OSHA PEL 15.00 UNITS
30% ECEILING NOT ESTAB
RECOMMD NOT ESTAB
CAS: 112926-008 AMORPHOUS SILICA GEL 1% OSHA PEL 6.00 MG/CU M
ECEILING NOT ESTAB
RECOMMD NOT ESTAB
SECTION 3: PHYSICAL DATA
Physical Properties Remarks
BOILING POINT DEG F NA
VAPOR PRESSURE MM HG AT DEG F NA
VAPOR DENSITY (AIR = 1.0) NA
SPECIFIC GRAVITY 1.6 – 1.8
PERCENT VOLATILE BY VOLUME 0.00
EVAPORATION RATE (BUTYL ACETATE = 1 NA
SOLUBILITY IN WATER NA
APPEARANCE AND ODOR POWDER WITH NO DISTINCT ODOR
MATERIAL SAFETY DATA SHEET
SECTION 4: FIRE AND EXPLOSION HAZARD
DESCRIPTION REMARKS
FLASH POINT ICC / PM DEG F DECOMPOSES WITHOUT FLASHING
LOWER EXPOLOSIVE LIMIT NA
UPPER EXPLOSIVE LIMIT NA
EXTINGUISHING MEDIA CARBON DIOXIDE, DRY CHEMICAL, FOAM, AND
/ OR WATER FOG
SPECIAL FIRE FIGHTING FIRE FIGHTERS MUST WEAR SELF CONTAINED
PROCEDURES BREATHING APPARATUS OR AIR MASKS
UNUSUAL FIRE AND EXPLOSIVE REFER TO NFPA 1977 EDITION OF 33 CHAPTER
HAZARDS 13 ORGANIC SOLIDS DUST WHEN SUSPENDED
IN AIR IN THE CORRECT RATIO IS FLAMMABLE
SECTION 5: HEALTH HAZARD DATA
DESCRIPTION REMARKS
THRESHOLD LIMIT VALUE NOT REQUIRED FOR MIXTURE
EFFECTS OF OVEREXPOSURE OVEREXPOSURE TO INGREDIENTS IN THIS
PRODUCT MAY CAUSE NOSE AND THROAT
IMMEDIATE EFFECTS (ACUTE) IRRIATATION, EYE IRRITATION, SKIN IRRITATION
DELAYED EFFECTS (CHRONIC) NOT KNOWN
MEDICAL CONDITIONS GENERALLY NOT KNOWN
AGGRAVATED BY EXPOSURE
EMERGENCY AND FIRST AID PROCEDURES
DESCRIPTION REMARKS
EYE CONTACT FLASH IMMEDIATELY WITH PLENTY OF WATER FOR AT
LEAST 15 MINUTES AND GET MEDICAL ATTENTION
SKIN CONTACT WASH THOROUGHLY WITH SOAP AND WATER
CLOTHING REMOVE CONTAMINATED CLOTHING AND SHOES, WASH
CLOTHING BEFORE REUSE, AND THOROUGHLY CLEAN
CONTAMINATED SHOES
INHALATION IF INHALED, REMOVE TO FRESH AIR, IF NOT BREATHING,
GIVE ARTIFICIAL RESPIRATION, IF BREATHING IS DIFFICULT,
GIVES OXYGEN, GET MEDICAL ATTENTION IMMEDIATELY
SWALLOWING IF SWALLOWED, CONTACT MEDICAL PERSONNEL
IMMEDIATELY TO DETERMINE BEST COURSE OF ACTION
POSSIBLE ROUTES OF INHALATION, INGESTION
ENTRY
MATERIAL SAFETY DATA SHEET
SECTION 6: REACTIVITY DATA
THIS PRODUCT IS STABLE
CONDITIONS TO AVOID NONE
INCOMPATIBILITY STRONG OXIDIZERS
HAZARDOUS DECOMPOSITION PRODUCTS CARBON DIOXIDE / MONOXIDE
HAZARDOUS POLYMERIZATION NONE
SECTION 7: SPILL OR LEAK PROCEDURES
SHOVEL UP AND DISPOSE OF IN AN AVOID CONTACT WITH EYES
APPROVED MANNER
WASTE DISPOSAL METHODS
1. PLACE THE POWDER, BACK IN THE CORRUGATED BOXES WITHOUT THE
POLYTHENE BAGS AND PUT THEM NEAR AN OVEN TILL THE POWDER
SOLIDIFIES. DUMP IT AS SOLID WASTE. (REF: BILL LEHR & ASSOCIATES,
POWDER COATINGS, 48 AUGUST 1994)
2. DISPOSE THE POWDER BY BURYING IT UNDER GROUND IN AN ISOLATED AREA
3. DISPOSE IN CHEMICAL DISPOSAL AREA OR IN A MANNER THAT COMPLIES WITH
LOCAL / NATIONAL REGULATONS.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION
REQUIRED FOR DUSTS AND FUME CONDITIONS.
VENTILATION
VENTILATION EQUIPMENT SHOULD BE EXPLOSION PROOF. CURING OVENS SHOULD BE
PROPERLY VENTED TO PREVENT RELEASE OF CURING OFF GASES INTO THE WORKPLACE
PROTECTIVE GLOVES : USUAL INDUSTRIAL HAND PROTECTION
EYE PROTECTION : USUAL INDUTRIAL EYE PROTECTION
OTHER PROTECTIVE EQUIPMENT : USUAL INDUSTRIAL WORK CLOTHES
MATERIAL SAFETY DATA SHEET
SECTION 9 : SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:
AVOID FREE FALL OF POWDER IN EXCESS OF A FEW INCHES, KEEP AWAY
FROM HEAT.
SPARKS AND OPEN FLAMES. KEEP CONTAINER CLOSED WHEN NOT IN USE. DO
NOT STORE ABOVE 49°C.
ABREVIATIONS USED
OSHA OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION
IRC INTERNATIONAL AGENCY FOR RESEARCH ON CANCER
LEL LOWER EXPLOSIVE LIMITS
UEL UPPER EXPLOSIVE LIMITS
MG CU M MILLIGRAMS PER CUBIC METER
MM MILLIMETERS
PPM/CF MILLIONS OF PARTICLES PER CUBIC FEET
MSHA MINE SAFETY AND HEALTH ADMINISTRATION
NA NOT APPLICABLE
NIOSH NATIONAL INSTITUTE OF OCCUPATIONAL SAFETY AND HEALTH
NOT ESTAB NOT ESTABLISHED
NTP NATIONAL TOXICOLOGY PROGRAM
PEL PERMISSIBLE EXPOSURE LEVEL
PPM PARTS PER MILLION
TCC TAG CLOSED CUP
PM –PENSKY MARTEN
RECM RECOMMENDED
TLV THRESHOLD LIMIT VALUE
DISCLAIMER SECTION
INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED TO BE
ACCURATE. M/s. MODERN SAK FACTORY FOR POWDER PAINT MAKES NO
WARRANTIES EXPRESS OR IMPLIED AND ASSUMES NO RESPONSIBILITY FOR THE
ACCURACY OR COMPLETENESS OF THE DATA. MODERN SAK FACTORY FOR POWDER
PAINT FURTHER ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE TO VENDEES, USERS, OR THIRD PARTIES CAUSED BY THIS MATERIAL.
SUCH VENDERS OR USERS ASSUME ALL RISKS ASSOCIATED WITH THE USE OF THIS
MATERIAL.
