Table of Contents

English
1. Your Watch ................................................................................................. 9
2. Before Use ................................................................................................ 12
• Checking the Reference Position ......................................................... 14
3. Basic Watch Operations .......................................................................... 16

Radio Signal Reception

4. Radio Signal Reception ........................................................................... 18
5. Poor Reception Areas .............................................................................. 23
6. Display during Reception ........................................................................ 24
7. Confirming Reception Status .................................................................. 26
8. Reception Area Guidelines...................................................................... 28
9. World City Display.................................................................................... 33
10. Charge Level Display ............................................................................... 38

1
Operations in Each Mode Solar Power
11. Changing Mode ........................................................................................ 40 24. Solar Power Function .............................................................................. 88
12. Using Home Time and World Time ......................................................... 42 25. Characteristics of the Solar Powered Watch......................................... 90
13. Using Daylight Saving Time .................................................................... 44 A. Power Saving Function ....................................................................... 92
14. Setting the Time (TME) ............................................................................ 46 B. Insufficient Charge Warning Function............................................... 94
15. Setting the Calendar (CAL)...................................................................... 50 C. Overcharging Prevention Function.................................................... 95
16. Using the Timer (TMR) ............................................................................. 54 D. Guide to Charging Time ...................................................................... 96
17. Using the Chronograph (CHR) ................................................................ 58 E. Handling Your Solar Powered Watch................................................. 98
18. Using the World Time Setting (WT-S)..................................................... 60
19. Using the World Time Alarm (AL-1 and 2) ............................................. 64 Troubleshooting
20. Using the Receive Setting (RX-S) ........................................................... 66 Radio Signal Reception Function ......................................................... 100
21. LED Lights ................................................................................................ 70 Eco-Drive................................................................................................. 104
22. Resetting Your Watch .............................................................................. 70 Precautions................................................................................................... 106
23. Adjusting the Reference Position........................................................... 72
26. Specifications ......................................................................................... 112
Using the Slide Rule Bezel ............................................................................ 76

2 3
 Please use this watch after it has been sufficiently
charged by exposure to light.
Congratulations and Thank You for your selection of a CITIZEN Eco-Drive watch. If the second hand of the watch is moving at two-second intervals, this indicates the
To get the most out of your purchase, please be sure to read this manual and keep it watch is insufficiently charged. To ensure proper operation, the watch should be fully
on hand for reference. charged by placing the watch under direct sunlight for about eight (8) hours. We
Once fully charged by exposure to light, your watch will give you years of recommend the watch keep a high charge level to ensure optimum operation.
enjoyment and reliability. Charge your watch as indicated in “Guide to Charging Time” (p. 96).

Notice
All repairs performed on this watch are to be performed at the CITIZEN.
When desiring to have your watch repaired or inspected, please contact the Citizen
Service Center either directly or through the store where you purchased your watch.

4 5
Part Names (1) Part Names (2): Digital Displays
UTC hour hand
UTC minute hand [Digital display 2] [Digital display 1]
Charge level indicator/ Home city name World city name
radio wave reception Home time minute hand
indicator
Button (B)

24-hour hand
Home time hour hand
Chronograph
Crown measurement mark
Insufficient charge
warning mark Timer measurement mark
Digital display 2
(Displays the home city) Alarm setting mark
Button (A) World city time Daylight saving time setting
Hour/minute/second mark
Home time second Digital display 1
hand Morning: A
(Displays world city/ Afternoon: P
Mode hand world time)
Note: To assist in the explanation, all parts of the digital display are shown in the illustration.
• The illustrations shown in this manual may differ from the actual watch you have purchased.
6 7
Part Names (3): Radio Wave Reception Display ■ 1. Your Watch
NO: Signal reception failed RX: Reception standby H, M, L: Reception level/ World Time Eco-Drive Radio Controlled Watch
reception status
<Radio Signal Reception Function>
This watch is a radio controlled watch, which receives the standard time radio waves that are
broadcast from radio wave transmitters in three regions, Japan, the USA and Europe
(Germany), and uses these waves to automatically correct the time and date. (p. 18)

◎ Automatic reception: The watch will automatically receive the radio wave up to three
times a day, at 2 a.m., 3 a.m. and 4 a.m., and adjust the time and date accordingly. However,
note that if the watch successfully receives the radio wave at 2 a.m., it will not perform
automatic reception again at the later times.
Modes where reception is The 4 a.m. automatic reception can be changed to any time of the day.
possible: CAL, TME and ◎ On demand reception: The radio wave can be received at any time of the day to adjust
RX-S the time and date.
In the event that a radio signal cannot be received, the watch can be manually set and will
operate keeping time within +/- 15 seconds per month.
JPN : JJY (Japan)
USA : WWVB (USA)
EUR : DCF77 (Germany)

8 9
<World Time Function> Important Points Regarding Radio Wave Reception
◎ UTC (Coordinated Universal Time), the time and date of 43 cities (or regions) from around There are two methods to receive radio signals during normal operation, Automatic and
the world and one city (any can be set) can be displayed and easily called up. It is On Demand.
convenient when traveling overseas on business or vacation. The internal unidirectional antenna may be weakened by geography or building
Daylight saving time can also be set. (p. 44)
structures, which may require the user to place the watch near a window.
When receiving radio waves:
<Solar Power Function>
* Remove the watch from your wrist
This is a multi-functional Eco-Drive watch, which is equipped with a solar power function for
powering the watch by converting light energy into electric energy.
* Face the 9:00 position of the watch towards a window
* Place the watch on a stable surface
◎ Charge level display function: This function displays the charge level in four grades, to * Do not move the watch during this process. Movement of the watch may cause
give an approximate indication of how much the secondary battery is charged. (p. 38) incomplete reception. During radio reception, the second hand of the watch moves in
reception level.
◎ Power saving function: The watch is equipped with two power saving functions. * When reception is complete, the watch will return to movement at one-second
If the watch face is not exposed to light for 30 minutes or longer, all the LCD display intervals.
sections turn off (Power saving 1). If the watch face is then not exposed to light for one Reception can take from about 2 minutes to a maximum of 15 minutes.
week or longer, the hands are stopped in order to minimize the watch’s power consumption
(Power saving 2). (p. 92)

10 11
■ 2. Before Use
NO: Signal RX: Reception Reception level/
reception failed standby reception status Check the movement of The second Your watch is
H : High the second hand. Check the correctly receiving
reception status. hand indicates
M : Middle The second hand is a reception the standard time
L : Low • Pull out the crown to radio wave.
moving at 1-second position 1. status of H, M
intervals. or L It is ready to use.
• Turn the crown to
Crown in its align the mode hand
normal position The second hand is with TME.
moving at 2-second • Return the crown to
intervals or is stopped. the normal position. The second
Button (A) Refer to “On Demand
• Press the lower right hand indicates Reception” (p. 20) to
Mode hand button (A) at the a reception perform the radio wave
4:00 position. status of NO reception.
(p. 26)
[Insufficient charging] [Fully charged] Charge the watch
Charge level sufficiently by placing it in If you are unable to
indicator direct sunlight as indicated receive radio waves,
in “Guide to Charging please inquire to the
Time” (p. 96). Citizen Service Center.

12 13
[Checking the Reference Position] 1. Pull the crown out to position 1 and turn to align UTC hour and
the mode hand with CHR (chronograph mode). minute hands

Before using the watch, confirm that the hands are aligned with 2. Pull out the crown to position 2.
“0”, similar to when setting weighing scales • The hands will move rapidly, stopping at the
Hour, minute
reference position recorded in the watch and second 24-hour
◎ The reference position may become misaligned when the
memory. hands hand
watch is exposed to strong magnetism, static electricity
or impacts. Even if radio waves are received, the correct
Correct reference positions
time will not be indicated unless the watch hands are
aligned to the correct reference position. Check that the Charge level indicator: EUR
hands are properly aligned with “0”. UTC hour and minute hands: 12:00
Hour, minute and second hands: 12:00:00
Examples of magnetic products that can affect the 24-hour hand: 12:00
watch.
• Health products (for example, medical necklaces and waist bands 3. If the reference position is correct, the check is
that have magnetic fields) complete. Press the crown back into its normal
• Refrigerators (magnetic part of the door) position. Charge level
• Electromagnetic cookers indicator
• If a position is incorrect, refer to “Adjusting the
• Bags (with magnet fasteners)
• Mobile phones (speaker part) Reference Position” and adjust it to the correct
Keep the watch away from items similar to those above. position. (p. 72) Mode hand

14 15
■ 3. Basic Watch Operations
* The watch receives the radio wave from the radio wave transmitter located in the
home city’s region.

Home time 1. 2. 3. 4.
Home time
hour hand minute hand Check the Set the home city. Set the home time. Set digital display 1.
charge level. If the city in which you If the home time is correct, The world time or date can be
(p. 38) are situated is displayed displayed on digital display 1.
in digital display 2, Also, the mode can be switched
(1) Set the time manually (p. 46)
Button (B) in order to use the alarm, timer
(1) Pull out the crown to
(2) Set the time by receiving the radio
or chronograph. (p. 40)
position 1 and turn to wave (p. 20)
align the mode hand
with TME. Caution:
Digital display 1 If the home city is set to a city that
(2) Press button (A) or (B)
to call up the home city is outside the reception area, the
Button (A) radio wave cannot be received.
in digital display 1.
(3) Press button (A) and Turn off the automatic reception
Home city button (B) at the same and set the time manually.
(Digital display 2) time to display the home (p. 66 ∼ 69)
city in digital display 2.
Home time second hand
16 17
■ 4. Radio Signal Reception Automatic reception
• It is not necessary to operate buttons during automatic reception.
Three types of radio signal reception are possible: automatic reception, on demand • The watch will automatically receive the radio wave every day at 2
reception and recovery automatic reception. a.m., 3 a.m. and 4 a.m.
There are three modes where reception is possible: time (TME), calendar (CAL) and ∼ 69)
• The 4 a.m. reception can be changed to any time of the day. (p. 66∼
receive set (RX-S). The watch cannot receive signals in any other mode. • Reception can be set to OFF. (p. 66 ∼69)
Display the home city in digital display 2 when receiving the radio wave.
<Receiving the radio signals>
• Reception is not possible unless the crown is in the normal position.
1. Remove the watch from your wrist and place on
• If the home city is “UTC”, reception is not possible.
a stable surface in a location, such as near a
• Reception is not possible during chronograph or timer measurement.
window, from which radio waves can be easily
• The reception level may change depending on the surrounding environment. While
received, pointing the 9:00 side (reception
referring to reception level (H, M or L), change the watch location, direction and angle
antenna position) in the direction of the radio
to try to receive the radio wave.
wave transmitter.
• When the watch is receiving the radio wave signal, all of the hands will stop.
2. The watch will automatically receive the radio
To check the time, hold the lower right button (A) for 2 seconds to cancel the radio
wave every day at 2 a.m. An antenna for receiving the radio
wave reception. The hands will then return to the current time. signals is located inside the watch
If it successfully receives the wave, reception is
not performed at 3 a.m. and 4 a.m. (on the 9:00 position).

18 19
 On Demand Reception (Manual Reception) Recovery Automatic Reception (Automatic Reception)
• Signals can be received at any time. • If the watch stops due to insufficient charging, expose the watch to
[Mode hand position sunlight to recharge it. When the watch is recharged sufficiently, it will
<Receiving the radio signals>
when receiving] automatically receive the radio wave once.
1. Pull the crown out to position 1 and turn to align the
mode hand with the CAL, TME or RX-S position. * Regularly charge your radio controlled watch so it does not become insufficiently
2. Return the crown to the normal position. charged.
3. Remove the watch from your wrist and place on a The radio wave reception can be checked with “Confirming
stable surface near a window where the radio signal Reception Status”. (p. 26)
can be easily received.

4. Point the 9:00 side of the watch in the direction of the radio wave transmitter, and hold
down the lower right button (A) for more than 2 seconds. Release when the
confirmation tone sounds and the second hand stops at RX. The second hand will then
move to H, M or L.
* Do not move the watch during reception.
5. When the radio wave has been properly received, the second hand will automatically
move from H, M or L to the time that was received, all the hands will be corrected,
and the second hand will return to 1-second interval movement.
20 21
<Storing Your Radio Controlled Watch> ■ 5. Poor Reception Areas
If the watch has received insufficient light for charging or has been kept in a dark
location for an extended period of time (one week or more), the Power Save Feature of It may not be possible to receive radio waves under environmental conditions where reception
is difficult or in areas susceptible to radio noise, such as those shown in the illustrations below.
the watch is activated and the hands of the watch stop. Even though the watch will not While referring to the reception level display, try to find a location with better reception.
show movement, the correct time is kept in memory. When the watch is in the Power
Save mode, it will continue to keep the correct time internally. In some instances,
“Automatic Reception” may not be successful due to a weak signal reception. When
resuming use of the watch after the power save mode has been activated for an extended
period of time, you can cancel the Power Save function by placing the watch in light
sufficient for charging and performing the “On Demand” reception process to correctly ◆ Near high-tension electrical ◆ Inside vehicles, including
set the time and date. (Refer to page 92 for information on the Power Save Function.) ◆ Inside reinforced concrete lines, railway overhead wires cars, trains and aero planes
buildings or underground or communication facilities

◆ Near TVs, refrigerators,

computers, fax machines and other ◆ Near cellular ◆ Extremely hot or cold locations
home electronics or appliances phones that are
22 in use 23
■ 6. Display during Reception <Time required for reception>
Reception can take from about 2 minutes to a
[During reception standby] [Receiving signal] [Reception completed] maximum of 15 minutes, depending on factors such
[Second hand display] as the weather or noise. If the radio wave reception
fails, the watch may return immediately to the
Radio wave normal display.
reception
indicator
[Caution] During reception, the second hand may
rotate once and show the reception level
◆ Second hand moves to RX and ◆ The second hand moves from ◆ When the reception is
again.
stops. RX to reception level H, M or L successful, the second hand Do not move the watch until the second
The radio wave reception and reception starts. will return to 1-second interval hand has returned to 1-second interval
indicator points to the received movement and the other hands
transmitter. will be automatically corrected. movement.
[Digital display]
Off Off

Repeatedly switches ◆ If the reception fails, RC and

between on and off NO are displayed.

24 25
■ 7. Confirming Reception Status Reception
level
Reception status

Radio wave reception environment was very

• The result of the radio wave reception can be confirmed. H
good
• The daylight saving time setting status of the home city can be confirmed.
M Radio wave reception environment was good
1. Set the mode to TME, CAL or RX-S. L Radio wave reception environment was not very
good
2. Press the lower right button (A) once to display the reception status. The second hand
will move to H, M, L or NO. NO Signal reception failed
• The daylight saving time setting status for the home time is displayed on digital
display 2 (flashes alternately between SMT and ON or OFF).
* The time display may shift slightly depending on the reception environment and
• The radio wave reception indicator points to [Digital display 2] internal watch processing even if radio waves are properly received.
JPN, EUR or USA.
* H, M and L indicate the reception status and are not connected to the performance of
3. Press the lower right button (A) once.
the watch.
• The watch returns to the normal time display
(1-second interval movement).
• If NO is indicated, find a location or direction where the reception is better and
• It also returns automatically to normal
perform on demand reception again. (p. 20)
display if there are no operations for 10
seconds.

26 27
■ 8. Reception Area Guidelines Standard time
radio signal
Transmitter Frequency

This watch can receive standard time radio waves broadcast from Japan (two Ohtakadoya-yama Standard Time Transmitter
40 kHz
(Fukushima Transmitter)
transmitters), the USA and Europe (Germany). JPN
JJY
The standard time radio wave to be received can be changed by selecting the city in Japan
Hagane-yama Standard Time Transmitter
60 kHz
another region. (Kyushu Transmitter)
The maps show the approximate reception areas. However, note that the radio wave
WWVB
condition could change due to factors including the weather (such as lightning) and USA Fort Collins Transmitter, Denver, Colorado 60 kHz
USA
changes in the season or sunrise/sunset time.
The reception area on the map is only guideline, and it may be difficult to receive the DCF77
EUR Mainflingen Transmitter, Southeast Frankfurt 77.5 kHz
Germany
radio signal even within the areas indicated on the map.
The standard time radio wave this watch uses is broadcast almost continuously 24-hours
a day, but may occasionally be interrupted for maintenance.
Even if reception of the standard time radio signal has failed, the watch will continue to
be accurate to within ±15 seconds per month.

28 29
 JPN: JJY (Japan) Automatically selects one of the two transmitters USA: WWVB (USA) Fort Collins: 3,000 km radius from the transmitter
Fukushima Transmitter: 1,500 km radius from the transmitter
Kyushu Transmitter: 2,000 km radius from the transmitter

30 31
 EUR: DCF77 (Germany) Mainflingen: 1,500 km radius from the transmitter
■ 9. World City Display
UTC (Coordinated Universal Time) and 43 cities (or regions) are registered in this watch
in advance, and it is also possible to register one additional city. The time of each city
can be called up and displayed.
• Press the upper right button (B) while the crown is in position 1 during TME mode or
CAL mode to display in sequence from the top left to bottom right the city names
shown in “Table of UTC Time Differences” (p. 35), and press the lower right button
(A) to display the city names in sequence from the bottom right to top left.
• When visiting a city other than the registered 43 cities, please display one of the
registered cities in the same time zone.

UTC: Coordinated Universal Time

This is the time of an atomic clock that is used as the global standard (= international atomic time).
It uses leap seconds to correct deviations in time systems that are based on the rotation of the Earth
(universal time).

32 33
 [Cities and the standard time radio [Table of UTC Time Differences]
wave assignment] Set to TME mode and press the upper right button (B) repeatedly while the crown is in
• The received standard time radio waves shown position 1 to display in sequence in digital display 1 the table’s city names from top to
in “Table of UTC Time Differences” are bottom, and press the lower right button (A) to display in sequence the city names from
assigned one of the following three radio wave bottom to top.
transmitters, in accordance with the home city
Received Received
in digital display 2. Watch Time standard Watch Time standard
City name City name
display difference time radio display difference time radio
wave wave
[Standard time radio wave
assignment] Coordinated CAI Cairo +2 EUR
UTC universal time 0 ---
Radio signal transmitter JPN : JJY (Japan) JNB Johannesburg +2 EUR
USA : WWVB (USA)
Digital display 2 LON London 0 EUR ATH Athens +2 EUR
EUR : DCF77 (Germany)
PAR Paris +1 EUR MOW Moscow +3 EUR
• Radio wave transmitters are assigned even for countries and regions outside the
reception area. ROM Rome +1 EUR RUH Riyadh +3 EUR
• Radio wave transmitter assignment does not guarantee reception. BER Berlin +1 EUR THR Tehran + 3.5 EUR
• For regions that are assigned Japan’s standard time radio wave (JJY), either the
Fukushima transmitter or Kyushu transmitter is selected automatically for reception, MAD Madrid +1 EUR DXB Dubai +4 EUR
whichever is easier to receive.
34 35
 Received Received Received Received
Watch Time standard Watch Time standard Watch Time standard Watch Time standard
City name City name City name City name
display difference time radio display difference time radio display difference time radio display difference time radio
wave wave wave wave

KBL Kabul + 4.5 EUR SEL Seoul +9 JPN DEN Denver -7 USA Fernando de
FEN Noronha -2 EUR
KHI Karachi +5 JPN ADL Adelaide + 9.5 JPN CHI Chicago -6 USA
DEL Delhi + 5.5 JPN SYD Sydney + 10 JPN MEX Mexico City -6 USA PDL Azores -1 EUR
DAC Dhaka +6 JPN NOU Noumea + 11 JPN NYC New York -5 USA Time difference set Any Depends
HOM by user on the time
RGN Yangon + 6.5 JPN AKL Auckland + 12 JPN YMQ Montreal -5 USA difference

BKK Bangkok +7 JPN SUV Suva + 12 JPN CCS Caracas -4 USA

SIN Singapore +8 JPN MDY Midway Islands - 11 USA RIO Rio de Janeiro -3 USA
HKG Hong Kong +8 JPN HNL Honolulu - 10 USA • Radio waves are only received from the assigned transmitters.
BJS Beijing +8 JPN ANC Anchorage -9 USA
(Example: WWVB radio waves cannot be received when TYO is displayed in digital
display 2)
TPE Taipei +8 JPN LAX Los Angeles -8 USA
TYO Tokyo +9 JPN YVR Vancouver -8 USA

36 37
■ 10. Charge Level Display [Checking the charge level display]
Level Level 0 Level 1 Level 2 Level 3
• The charge level (approximate) is displayed in four grades to show how much the
secondary battery is charged. Charge
• The charge level indicator points to the middle of each grade. level
display
• Use the charge level display as a guideline when wearing your watch. We recommend
that you regularly check the charge level and keep it at level 2 or above.
About 3 to About 20 to About 130 to
About 3 days 20 days 130 days 180 days
Insufficient The charging level The charge The watch is
Remaining charging. Recharge is rather low. condition is good. sufficiently charged.
time the watch Recharge the The watch can be The watch is fully
(approximate) immediately. watch. used normally at charged and can be
The insufficient this level. used normally at
charge warning is this level.
activated at this
level.
[Caution]
When the charge level indicator points at level 0, the secondary battery is very low. The second hand
moves at 2-second intervals, and the mark flashes in the digital display.
After about three days the battery will run out and the watch will stop. Be sure to recharge the watch
before this condition is reached.
38 39
■ 11. Changing Mode <Mode names> 【WT-S】
World time set
* Crown in position 1
This watch has eight modes: time (TME), calendar (CAL), timer (TMR), chronograph
(CHR), world time set (WT-S), alarm 1 (AL-1), alarm 2 (AL-2) and receive set (RX-S). 【CHR】 【AL-1】
1. Pull the crown out to position 1 (mode switching position). Chronograph Alarm 1
• The home city and (M) are displayed alternately on digital display 2 to show that the
mode switching status has been entered.
2. Turn the crown to the right or left to align the mode hand with the desired mode.
3. Return the crown to the normal position. 【TMR】 Turn the Turn the 【AL-2】
Timer crown to crown to Alarm 2
the right the left

Digital Mode switching

display 2 position

Displayed 【CAL】 【RX-S】

alternately Calendar Receive set
Mode adjustment
position Mode hand 【TME】
Time
40 41
 Example: During time mode (TME)
■ 12. Using Home Time and World Time
• When going to a country or region in a different time zone when on business or vacation, the Los Angeles Switch New York
destination home time can be easily displayed by switching the home time and world time.
* Switching can only be performed during the time mode (TME) or calendar mode (CAL). Pull the crown out to
Button (B) position 1 and press
<Switching between home time and world time> buttons (A) and (B) at
Example: Going to New York from Los Angeles the same time.
When Los Angeles time “10:09 a.m.” is displayed for the home time
(hand display) and New York time “P1:09” is displayed for the world The hands also change
time (digital display) at the same time.
1. Pull the crown out to position 1 (mode switching position).
Digital Button (A)
• The home city LAX and (M) are displayed alternately on digital display 2, to show that the
display 2 Digital display 1
mode switching status has been entered.
2. Turn the crown to enter time mode (TME) or calendar mode (CAL). [Digital display 2] [Digital display 2]
3. Press button (A) and button (B) at the same time. Home city: LAX (Los Angeles) Home city: NYC (New York)
• A confirmation tone sounds, and the Los Angeles and New York city names and times are Home time (hand display): 10:09 a.m. Home time (hand display): 1:09 p.m.
switched.
• The date is also switched at the same time. [Digital display 1] [Digital display 1]
4. Turn the crown to return to the original mode. World city: NYC (New York) World city: LAX (Los Angeles)
5. Return the crown to the normal position to complete the operation. World time (digital display): P1:09 World time (digital display): A10:09

42 43
■ 13. Using Daylight Saving Time [Daylight saving time list]
To deactivate
Radio wave
Mode Setting item To set manually daylight saving
◎ To change automatically to daylight saving time by receiving the radio reception setting
time
wave
• By setting the daylight saving time reception setting in RX-S mode to AU, when the Daylight saving
RX-S time reception AU mA mA
radio wave is received, the time will be automatically updated with the daylight saving setting
time information of the received radio wave.
* The home city must be a city within the reception area. TME Daylight saving
* The timing for changing to daylight saving time can vary depending on the city or ON or OF (off) ON OF
WT-S time setting
region. There may be cases when the time is not changed on the appropriate date.
* Refer to the explanations for each mode for details on the operations.
◎ To manually set daylight saving time
• To manually set daylight saving time, set the RX-S mode to mA, select the city in
TME mode (or WT-S mode), and set the daylight saving time setting to ON. [What is daylight saving time?]
◎ To deactivate daylight saving time This is a time system where the clocks are put forward an hour during the summer, when the
• To deactivate daylight saving time, set the RX-S mode to mA, select the city in TME daylight hours are longer.
Whether or not the system is used and the length of use differs between countries and regions.
mode (or WT-S mode), and set the daylight saving time setting to OF (off).

44 45
 3. Pull the crown out to position 2 to enter the time correction status.
■ 14. Setting the Time (TME) • The second hand will move to the 12:00 position and stop.
(The time is corrected using the digital display) • The home city display of digital display 2 will go off.
• The time can be set manually in countries or regions where the radio wave cannot be • The correction status for the daylight saving time setting is entered and ON or OF
received. flashes. (There is no daylight saving time ON or OF setting for UTC.)
• To set the time, call up the city whose time you want to correct in digital display 1. The • Press the lower right button (A) to switch between setting (ON) and canceling (OF)
home time (hour/minute/second hands) cannot be corrected directly. the daylight saving time.
• It is possible to change the daylight saving time setting in TME mode. • When daylight saving time is set, the time moves forward by one hour.
• Each time the upper right button (B) is pressed, the correction location changes. The
<Correcting the time> new correction location will begin flashing.
1. Pull the crown out to position 1 and turn to align the mode hand with TME (time 4. Press the upper right button (B) to enter the second correction status.
mode). • Press the lower right button (A) to return to 0 seconds.
2. Press button (A) or (B) to call up the city name whose time you want to correct. 5. Press the upper right button (B) to enter the minute correction status.
• When setting the home city time (hour, minute, second hands), switch the home city • Turn the crown to correct the time. Turn to the right to move forward and to the left
and world city before correcting the time. (Refer to “Switching between home to move back.
time and world time” p. 42) • Turn the crown continuously to move quickly. To stop, turn the crown to the left or
right.

46 47
6. Press the upper right button (B) to enter the hour correction status. • Daylight saving time can be set for
Position 1
• Turn the crown to correct the time. Turn to the right to move forward and to the left each city.
to move back. Button (A)/(B) • When the time is set for one of the
Button (B)
• Turn the crown continuously to move quickly. cities, the times for all the other cities
7. Press the upper right button (B) to enter the 12H/24H correction status. Select the city are also corrected automatically.
• Press the lower right button (A) to switch between the 12-hour clock and 24-hour
clock.
• This setting is applied even in other modes.
8. Return the crown to the normal position to complete the operation.
Position 2
• When the home time is corrected, the analog time, which is linked to the digital
time, is also corrected.
Daylight saving Correct the Correct the
time setting second minute
(B)
Button (B)
(B)
Button (A)
Switch between
Correct the hour
(B) 12H and 24H
(B)

48 49
 4. Each time the upper right button (B) is pressed, the correction location changes. The
■ 15. Setting the Calendar (CAL) new correction location will begin flashing.
(The date is corrected using the digital display) • The correction location changes in the following sequence: month → date → year.
• The date can be set manually in countries or regions where the radio wave cannot be 5. Select the correction location and turn the crown to correct the time.
received. Turn to the right to move forward and to the left to move back.
• In the same way as for “Setting the Time”, to adjust the date of the home city, call up • Turn the crown continuously to move quickly.
the city whose date you want to correct in digital display 1. To stop, turn the crown to the left or right.
• When the year, month and date are set, the day is corrected automatically.
<Correcting the date> 6. Press the crown back into its normal position.
1. Pull the crown out to position 1 and turn to [Digital display 2] [Digital display 1]
align the mode hand with CAL (calendar
mode).
2. Press button (A) or (B) to call up the city
name whose date you want to correct.
3. Pull the crown out to position 2 to enter the
date correction status. Off
• The month display flashes and the home
city display and day display will go off.

50 51
 <Date correction status> • When the date is set for one of the cities, the dates for all the other cities are also
corrected automatically.
Button (B) Position 1
Select the city • The year can be set between 2000 and 2099.
• When the year, month and date are set, the day is corrected automatically.
• If a date that does not exist is set (for example, February 30), when the watch returns to
Position 2 the normal display, it automatically displays the first day of the next month.
Correct the month
Button (A)
Button (B)

Correct the date

(B)

Correct the year

(B)

52 53
 3. Turn the crown to set the time.
■ 16. Using the Timer (TMR) • Turn to the right to increase the time and turn to the left decrease the time.
• Turn the crown continuously to move quickly.
• The timer can be set from 1 minute up to 99 minutes, in 1-minute units. After the end
To stop, turn the crown to the left or right.
of measurement, the time-up tone sounds for about 5 seconds and the watch returns to
4. After completing the settings, return the crown to the normal position.
the timer initial setting status. (Auto return function)
• Digital display 2 changes to RES (reset).
• Press the lower right button (A) during measurement to return to the initial set time and
start measurement again. (Flyback function)

<Setting the timer> Minute display flashes

1. Pull the crown out to position 1 and turn to
align the mode hand with TMR (timer
mode).
2. Pull the crown out to position 2 to enter the
Settings
timer setting status. complete
• SET is displayed in digital display 2 and
the minute display in digital display 1
flashes.
[Digital display 2] [Digital display 1]

54 55
<Using the timer> 4. When the time is up, END is displayed in digital display 2 and the time-up tone sounds for 5
1. A confirmation tone will sound each time you press the upper right button (B) to start and seconds.
stop the measurement. • To stop the time-up tone, press button (A) or (B).
• RUN (run) is displayed in digital display 2 during measurement, and STP (stop) is • RES is displayed on digital display 2 and the timer returns to the initial set time.
displayed when the timer is stopped. The measurement mark comes on during * Radio waves cannot be received during timer measurement.
measurement. * The measurement continues even if the watch is switched to a different mode during
2. Press the lower right button (A) during measurement to return to the initial set time and start measurement.
measurement again. * The time-up tone does not sound unless the crown is in the normal position.
3. Press the lower right button (A) while the timer is stopped to return to the initial set time.
• Digital display 2 changes to RES.

Button (B) Button (B)

Measurement
mark
[Digital display 2] [Digital display 1]
56 57
 • While the chronograph is being operated, the display of digital display 2 changes as
■ 17. Using the Chronograph (CHR) follows.
• The chronograph can display times up to 23 hours 59 minutes and 59.99 seconds. (Reset) (During measurement)
• After it exceeds 24 hours, the chronograph returns automatically to the reset status.
Button (B)
<Using the chronograph> Button (B)
1. Pull the crown out to position 1 and turn to align the
mode hand with CHR (chronograph mode). Button (A) (B) (A)
2. Return the crown to the normal position.
Mode *
3. A confirmation tone will sound each time you press switching
the upper right button (B) to start and stop the (A)
position (B)
measurement.
4. Press the lower right button (A) during measurement Button (A)
(A)
to display a split time for 10 seconds. After the 10 seconds, the
watch returns to the measurement status. (Auto return function) (Measurement stopped) (Split display)
• The measurement mark is displayed during measurement and * If there are no button (A) or (B) operations for 10 seconds, the watch returns to the
during the split display. measurement status.
• The SPL display flashes during the split time display.
• Radio waves cannot be received during chronograph measurement.
5. Press the lower right button (A) while the chronograph is
stopped to return to the chronograph reset status. • The measurement continues even if the watch is switched to a different mode during
measurement.
Measurement mark
58 59
 3. Press the lower right button (A) to switch between daylight saving time ON (set) and OF (canceled).
■ 18. Using the World Time Setting (WT-S) • When daylight saving time is set, the time will move forward by one hour.
• Turn the crown to set the daylight saving time for other cities. Turn to the right to change in the
• Daylight saving time can be set for each city (44 cities other than UTC) with the world time setting. direction of cities with more of a time difference, and turn to the left to change in the direction of
• Whether show or hide each city (44 cities other than UTC) can be set. cities with less of a time difference.
* Using this function, it is easy to call up and display the cities from each mode. (Zone set function) 4. Press the upper right button (B) to switch between the show/hide setting status for the city.
* If a city is set to not display, it cannot be displayed from other modes. • SET (show) or OFF (hide) flashes.
• Any time difference in units of 15 minutes can be set for HOM (user setting city). • The initial settings are all SET (show).
5. Press the lower right button (A) to select SET or OFF.
[NOTE] • Press the lower right button (A) to switch between displaying SET and OFF, and then select the
Even if daylight saving time is set for each city in WT-S mode (ON or OF (off)), if AU is set in RX-S desired setting.
mode, priority is given to the daylight saving time setting in RX-S mode, with ON automatically • Turn the crown to set other cities.
switched to OF or OF automatically switched to ON. 6. Press the crown back into its normal position.
(Users in countries or regions without a radio wave transmitter should make sure that the start date and
finish date of daylight saving time are accurate.) City name
Button (B) City
<“Daylight saving time” and “Show/hide city” settings> Display (SET)/
Mode switching
1. Pull the crown out to position 1 and turn to align the mode hand with WT-S (world time set mode). Hide (OFF)
position
2. Pull the crown out to position 2 to enter the world time correction status.
• Digital display 2 goes off, digital display 1 enters the daylight saving time setting status for the city Correction position Daylight saving time
that is displayed, and ON or OF flashes. Button (A) Set (ON)/
• The initial settings are all OF (canceled). Canceled (OF)
[Digital display 1]

60 61
<Setting the desired time difference> 4. Press the upper right button (B) twice to enter the [Time difference setting status]
• Any time difference can be set between the HOM city and the UTC time, in units of 15 time difference setting status.
minutes. (Range of -12 to +14 hours from UTC) • Each time you press the upper right button (B), the
• The radio wave received at HOM will be from the transmitter assigned to the city that has the “Daylight saving time ON/OF”, “City display
most similar time difference with UTC. SET/OFF” and “Time difference setting” correction 0:00 flashes
location changes. The new correction location will
1. Pull the crown out to position 1 and turn to align the mode hand with WT-S (world time set begin flashing.
mode). 5. Turn the crown to set the time difference.
2. Pull the crown out to position 2 to enter the world time correction status. • Turn to the right to display (+) in the world time
3. Turn the crown to call up HOM for the world city. section and display time differences with UTC in
• ON or OF flashes and the watch enters the daylight saving time setting status. 15-minute units in the time display section.
• Turn to the left to display (–) in the world time
section and display time differences with UTC in
[Digital display 2] [Digital display 1]
15-minute units in the time display section. When a time difference of +5
• Turn the crown continuously to change the time hours 45 minutes with UTC is set
difference quickly. Turn crown to the right or left to
stop the quick movement.
Daylight saving Turn the crown to 6. Press the crown back into its normal position.
time ON/OF flashes select HOM * If the time difference is not set, the HOM city will
not be displayed regardless of whether the display
is set to SET or OFF.

62 63
■ 19. Using the World Time Alarm (AL-1 and 2) • The correction location changes in the following sequence: Alarm ON/OF → City name →
Alarm: Hours → Alarm: Minutes.
• City name: Turn the crown to select the city.
• An alarm can be set for the set city time.
• Alarm hours/minutes: Turn the crown to the right to move the time forward and to the left
• Once a day, the alarm will sound for 15 seconds when it reaches the set time. To stop the
to move the time back.
alarm, press button (A) or (B).
Turn the crown continuously to move quickly. To stop, turn the crown to the left or right.
• The sound of the alarm is different for alarm 1 and alarm 2, but the setting method is the same.
5. Press the crown back into its normal position.
<Setting the alarm time> <Alarm 1 or 2 correction status>
1. Pull the crown out to position 1 and turn to align the mode Button (B)
Select alarm ON or OF (off)
hand with AL-1 or AL-2 (alarm mode). Button (A)
2. Pull the crown out to position 2 to enter the alarm correction Button (B)
status. Position 2
• The set city is called up and ON or OF flashes. Select the city (turn the crown)
3. Press the lower right button (A) to set alarm ON (set) or OF Button (A)
(canceled). Alarm (B)
• Press the lower right button (A) to switch between ON and mark
<Alarm tone check> Correct the hour (turn the crown)
OF. Alarm ON/OF
• The alarm mark comes on when ON is set. In AL-1 or AL-2 mode, the alarm tone can be (B)
4. Each time the upper right button (B) is pressed, the display checked by pulling the crown out to position 1
Correct the minute
flashes and the correction location changes. and pressing the lower right button (A). (turn the crown) (B)

64 65
 mA (Manual): The time is not updated with the daylight saving time from the received radio
■ 20. Using the Receive Setting (RX-S) wave.

[Daylight saving time reception setting] [Automatic reception setting]

• Select whether to update the time with the daylight saving time from the received radio wave. • Set the operating conditions for automatic reception.
AU (Auto): The time is updated with the daylight saving time from the received radio wave. MAN (Manual): The 4 a.m. automatic reception can be changed to any time of the day for the
* The timing for changing to daylight saving time can vary depending on the city or home time.
region. There may be cases when the time is not changed on the appropriate date. * The time can be changed in 1-hour units. It cannot be set to 2 a.m. or 3 a.m.
* If AU is selected, when daylight saving time data is received for the daylight saving time OFF (Off): Automatic reception is not performed.
setting of the home city, the setting is changed to ON, and when no daylight saving time AUT (Auto): Automatic reception is performed according to the initial settings
data is received, the setting is changed to OF (off). (at 2 a.m., 3 a.m. and 4 a.m.).
* If the home city setting is included in group 1 or 2 shown below, the settings for other
cities are also changed to ON or OF (off) at the same time after reception.

[Group 1] [Group 2]
LON London MAD Madrid ANC Anchorage CHI Chicago
PAR Paris ATH Athens LAX Los Angeles MEX Mexico City
ROM Rome MOW Moscow YVR Vancouver NYC New York
BER Berlin PDL Azores DEN Denver YMQ Montreal

66 67
<Setting procedure> 4. Press the upper right button (B) to enter the automatic reception setting status.
1. Pull the crown out to position 1 and turn to align the mode hand with RX-S (receive • The set automatic reception status flashes.
set mode). • AUT, MAN and OFF flash and the watch enters the correction status.
2. Pull the crown out to position 2 to enter the daylight saving time (SMT) reception 5. Press the lower right button (A) to set the automatic reception operating condition to
setting status. MAN.
• AU or mA flashes and the watch enters the correction status. • The hour of the reception time flashes.
• Each time the upper right button (B) is pressed, the display switches between the • Each time the lower right button (A) is pressed, the correction location changes in
daylight saving time reception setting and the automatic reception setting. the following sequence: AUT → MAN → OFF.
3. Press the lower right button (A) to select AU or mA. 6. To change the reception time, turn the crown to change the time in 1-hour units.
• Turn the crown to the right to move the time forward and to the left to move the time
back.
[Daylight saving time [Automatic reception setting] • Only the 4 a.m. automatic reception can be changed. (2 a.m. and 3 a.m. are not
reception setting] displayed.)
• Only the hour can be changed, and when using the 12-hour clock, “A” indicates a.m.
Button Button and “P” indicates p.m.
(A) (A)
Button (A) Button (B) 7. Press the crown back into its normal position.
* Nighttime is usually a good time for reception because radio wave noise is relatively
Turn the crown Button (A) low.

68 69
■ 21. LED Lights <Resetting procedure>
All parts displayed
1. Pull the crown out to position 1 and turn to align
• Press the upper right button (B) while the crown is in the normal position to turn on the LED lights of the mode hand with CHR (chronograph mode). [Digital display 2] [Digital display 1]
digital displays 1 and 2 for three seconds. However, note that the lights do not come on in the 2. Pull out the crown to position 2.
following cases. • The hands will rotate rapidly.
* During timer mode or chronograph mode
3. After the hands stop, press buttons (A) and (B) at
* During radio wave reception
the same time.
* During 2-second interval movement (insufficient charge warning status)
• When you remove your finger from the buttons,
all parts of the digital displays and the lights will
■ 22. Resetting Your Watch come on.
• The confirmation tone sounds, the hands move
• If the watch displays or operates abnormally due to a strong impact or the effects of static electricity,
clockwise and counterclockwise and the watch switches to the reference position checking
reset the watch and then correct the reference position.
status.
[Caution] After resetting, all the mode settings return to their initial settings. Perform the settings
again as required. 4. If the reference position is incorrect, correct it.
(Refer to “Checking the Reference Position” (p. 14) and “Adjusting the Reference Position”
<Initial settings after resetting> (p. 72).)
• Home city/world city: UTC • Time: 0:00:00
• Date: January 1, 2007 (Monday) • Timer: 99 minutes 00 seconds
• Chronograph: 0 hours 00 minutes 00 seconds (reset status)
• World time: City displays - all SET, daylight saving time - all OF (off)
• Alarm 1/2: City - UTC, time - 12:00, set - OF (off)
• Receive set: Daylight saving time - AU, automatic reception - AUT
70 71
■ 23. Adjusting the Reference Position 4. ① Adjusting the charge level indicator
(1) Display CHA in digital display 2.
(2) Turn the crown to align the charge level indicator of
UTC hour 1. Pull the crown out to position 1 and the watch face with the center of EUR.
and minute
turn to align the mode hand with CHR. * Turn the crown continuously to move quickly. To stop,
hands
24-hour hand turn the crown to the left or right.
2. Pull the crown out to position 2. The * If no correction is required, proceed to the next step.
hands will move rapidly and stop at the
Hour, minute and
reference position (12:00 position) Press the upper right
second hands
Button (B) recorded in the watch memory. button (B).

3. When the upper right button (B) is 5. Each time the upper right button (B) is pressed in the reference position correction status,
pressed for more than 2 seconds, CHA digital display 2 changes in the sequence CHA → UTC → HR → MIN, and the
flashes in digital display 2 and the corresponding hand moves to show the location to be corrected.
watch enters the reference position
correction status. ① [Charge level ② [UTC hand] ③ [Hour hand] ④ [Minute hand]
indicator]
Charge
(B) (B) (B)
level Button (A)
indicator
Mode hand
Digital display 2 Button (B)

72 73
6. ② Adjusting the UTC hands (hour hand and minute hand) 8. ④ Adjusting the minute hand
(1) Press the upper right button (B) to display UTC in the digital display. (1) Press the upper right button (B) to display MIN in digital display 2.
(2) Turn the crown to align the UTC hour hand and minute hand with (2) Turn the crown to align the minute hand with 12:00.
12:00.
• Press the lower right button (A) to move the
minute hand by -3 minutes to make the UTC
hand easier to see.
Press the lower right button (A) again to return
Press the upper the minute hand to its original position.
right button (B). UTC hour and minute hands 9. When the upper right button (B) is pressed for more than 2 seconds after adjusting all the
hands to their correct reference positions, (0) is displayed in digital display 2 to show that the
7. ③ Adjusting the hour hand reference position adjustment is completed.
(1) Press the upper right button (B) to display HR in digital display 2. 10. Put the crown in position 1, set to the mode that you usually use, and then return the crown
(2) Turn the crown to align the hour hand with 12:00. to the normal position.
• Press the lower right button (A) to move the minute hand by -3
minutes to make the hour hand easier to see.
Press the lower right button (A) again to return the minute hand to
its original position.
* The 24-hour hand moves in tandem with the hour hand, so
Press the upper make sure that the a.m. and p.m. setting is correct.
right button (B).
74 75
 A. Navigation Calculator
Using the Slide Rule Bezel
1. Calculation of time required
Flying distance and other navigation Inside scale Problem: How long does it take an airplane flying at 180 knots to fly a distance of 450
calculations as well as general
nautical miles?
calculations can be performed using the
Outside scale Solution: Set the 18 mark on the outside scale to the SPEED INDEX (▲). At this
slide rule bezel located around the outside
time, the point on the inside scale that is aligned with 45 on the outside scale
of the dial. This slide rule bezel is not
indicates (2:30), and the answer is 2 hours and 30 minutes.
able to display decimal places for
calculation results, and should only be
used as a general reference as an
alternative to more accurate calculations.

76 77
2. Speed (Ground Speed) Calculation 3. Flying distance calculation
Problem: What is the speed (ground speed) of an airplane when it takes 1 hour and 20 Problem: What is the flying distance traveled in 40 minutes at a speed of 210 knots?
minutes to fly a distance of 240 nautical miles? Solution: Align the 21 on the outside scale with the SPEED INDEX (▲) of the inside
Solution: Align the 24 on the outside scale with 1:20 (80) on the inside scale. At this scale. The 40 of the inside scale is now pointing to 14, and the answer is 140
time, 18 is aligned with the SPEED INDEX (▲) on the inside scale, and the nautical miles.
answer is 180 Kt.

78 79
4. Fuel consumption rate calculation 5. Fuel consumption calculation
Problem: If 120 gallons of fuel are consumed in 30 minutes’ flying time, what is the Problem: How much fuel is consumedin 6 hours at a fuel consumption rate of 250
fuel consumption rate? gallons per hour?
Solution: Align the 12 of the outside scale with 30 of the inside scale. The SPEED Solution: Align the 25 of the outside scale with the inside scale’s SPEED INDEX (▲)
INDEX (▲) now points to 24, and the answer is 240 gallons per hour. of the inside scale. The 6:00 is aligned with 15, and the answer is 1500
gallons.

80 81
6. Maximum flying hours 7. Conversion
Problem: With a fuel consumption rate of 220 gallons per hour and a fuel supply of Problem: How do you convert 30 miles into nautical miles and kilometers?
550 gallons, what is the maximum number of flying hours? Answer: Align the 30 on the outside scale with the STAT (▲) mark on the inside
Solution: Align the 22 of the outside scale with the inside scale’s SPEED INDEX (▲) scale. At this time, 26 nautical miles is aligned at the NAUT (▲) mark on
of the inside scale. The 55 of the outside scale is now aligned with 2:30, and the inside scale, while the answer of 48.2 kilometers is aligned at the
the answer is 2 hours and 30 minutes. kilometers on the inside scale.

82 83
B. General calculation functions 2. Division
Problem: 250/20
1. Multiplication Solution: Align 25 on the outside scale with 20 on the inside scale. On the outside
Problem: 20 × 15 scale read the 12.5 mark that is aligned with 10 on the inside scale. figure the
Solution: Align 20 on the outside scale with 10 on the inside scale, and read the number of decimal places, and the answer is 12.5.
outside scale at the 30 mark which is aligned with 15 of the inside scale.
Figure the number of decimal places, and the answer is 300.
Remember: decimal places cannot be read on this scale.

84 85
3. Reading Ratios 4. Determining Square Root
Problem: 30/20 = 60/x Problem: What is the square root of 225?
Solution: Align 30 on the outside scale with 20 on the inside scale. At this time, the Solution: Rotate the scales so that the value on the inside scale corresponding to 22.5
answer of 40 can be read from the inside scale corresponding to 60 on the on the outside scale is equal to the value on the outside scale corresponding
outside scale. In addition, the ratio of the value on the outside scale to the to 10 on the inside scale, and read off the answer of 15 at that location.
value on the inside scale is 30:20 at all positions on the scales.

86 87
■ 24. Solar Power Function ◆ Wearing clothes with long sleeves makes it difficult for the watch to get the
necessary light, resulting in insufficient charging.
We recommended that you charge the watch for a long time in direct sunlight once a
This watch uses a secondary battery to store electrical energy.
month.
When the watch is fully charged, it will run for about 6 months.

<Ensuring best operation of the watch>

[Caution] Do not charge on surfaces that can easily become hot, such as a car
For best operation, charge your watch in direct sunlight. dashboard.
◆ An effective way of charging the watch is to keep it in a
bright location when you are not wearing it, such as
near a window where it can receive direct sunlight.

88 89
 * 1. When the watch stopped due to insufficient charging
■ 25. Characteristics of the Solar Powered Watch • It takes at least 30 minutes to recharge sufficiently to perform recovery automatic reception, even
if the watch is being exposed to light.
◎ When the watch is insufficiently charged, the indication will be changed as follows: After recovery, refer to “Guide to Charging Time” (p. 96) and sufficiently charge the watch.
* 2. If the watch failed to perform recovery automatic reception
• The time is incorrect even if the second hand moves at 1-second intervals, so after fully charging
the watch, set the time manually or perform on demand reception.

[Normal display] [Insufficient charge warning] [Recovery automatic reception]

The watch has been The insufficient
insufficiently charged charge warning (a Sufficiently charge
because the watch face, 2-second interval by exposing the
which contains the solar movement) watch face, which
cell, has not received continues for more contains the solar
The watch will cell to light.*1
sufficient light. than 3 days. stop due to an
insufficient
charging.
2-second interval
movement
When the watch is recharged
sufficiently, it will receive the radio
The second hand starts to move in 2-second intervals When a radio signal has been signal automatically once.
and the mark flashes in digital display 1. successfully received*2
90 91
A. Power Saving Function <Canceling the power saving function>
If the watch face is not exposed to light for a long time, the power saving function is activated The power saving function will be automatically canceled when the watch face is
to minimize the battery consumption. exposed to light.
• Power saving 1: When power is not generated for more than 30 consecutive minutes, the
• When power saving 1 is canceled, the digital display is restored.
digital displays go off to save power.
• Power saving 2: When the power saving 1 condition continues for 7 days or longer, to save • After the power saving 2 has been canceled, the hands will rapidly move to the current
power, the hour hand, minute hand, second hand and 24-hour hand move to time and return to 1-second interval movement.
the reference position, and the charge level indicator and UTC hands (hour • If the watch is insufficiently charged, the second hand will begin the 2-second interval
and minute) stop in their current positions. movement. Return the second hand to 1-second interval movement by sufficiently
• The correct time continues to be kept inside the watch. charging the watch.
• The alarm tone will not sound.
[Normal diaplay] [Power saving 1] [Power saving 2]
The digital
display areas
Digital display all go off and
areas all go off the hands stop.

Not exposed to light Not exposed to light

for 30 minutes or more for 7 days or more
92 93
B. Insufficient Charge Warning ◆ If the charging insufficiency occurs during radio signal reception, the operation will
Function stop automatically, the watch will return to the time before the operation, and 2-
When the charge level indicator reaches level 0, the second interval movement will begin.
second hand’s movement changes from 1-second Regularly charge your radio controlled watch so it does not become insufficiently
intervals to 2-second intervals and the mark charged.
flashes in digital display 1 to show that the watch is
insufficiently charged.
2-second
The watch will stop due to insufficient charging about 3
days after starting the 2-second interval movement if
interval movement C. Overcharging Prevention Function
kept in a place with no light. When the secondary battery becomes fully charged by exposing the watch face to light,
the overcharging prevention function is automatically activated to prevent the battery
[Caution] During 2-second interval movement, the digital displays and watch operations
change as follows. from being charged further.
• The time cannot be adjusted manually, or by using automatic reception or on demand
reception. No matter how much the watch is charged, it will not affect the secondary battery,
• Push button operations are not possible. timekeeping, functions or performance of the watch.
• All modes change to time mode.
• The alarm tone and confirmation tone will not sound. (When the timer, chronograph or
alarm is used)
• The LED lights will not come on.
• The chronograph and timer are forcibly reset and cannot be operated.

94 95
D. Guide to Charging Time For a 1-day movement charging time ... The charging time to run the watch for one day
The charging time varies according to the model (including the color of the watch face). with normal movement.
The following data should only be used as a guideline. Time for full charging ... The time for full charging after the watch has stopped due to an
insufficient charging.
*The charging time is based on continuous exposure.
Charging time (approximate) [Caution] A fully charged battery will run the watch for about 6 months without further
Luminescence Time from charging.
Environment For a 1-day stopping to
(lx)
movement resuming the Time for full The watch will maintain its accuracy for about 2 and a half years when
charging time 1-second interval charging
running in the power saving mode.
movement
Charge the watch every day, as it will take a long time to recharge it, as is
500 Indoor lighting 4 hours 30 hours ------ indicated in the table, when it stops due to an insufficient charging.
1,000 60 to 70 cm beneath a 30 W fluorescent light 2 hours 14 hours ------ We recommended that you charge the watch for a long time in direct sunlight
once a month.
3,000 20 cm beneath a 30 W florescent light 40 minutes 5 hours 150 hours

10,000 Cloudy sky 12 minutes 2 hours 60 hours

100,000 Direct summer sunlight 4 minutes 40 minutes 20 hours

* If the second hand is moving in 2-second intervals, refer to “Time for full charging” and fully
charge.

96 97
E. Handling Your Solar Powered Watch
CAUTION Charging precautions
◆ Do not charge the watch in a high-temperature environment (about 60°C / 140°F or
WARNING Handling the secondary battery more).
◆ Do not remove the secondary battery from the watch yourself, unless unavoidable. Overheating while charging can cause the watch exterior to become discolored, the
If you must remove the battery, store it out of reach of children to avoid accidental watch to deform or the movement to be damaged.
ingestion. If the secondary battery is ingested, consult a doctor immediately. Example:
◆ Do not throw away with regular trash. • Charging close to incandescent lighting, halogen lamps, or other lighting sources
Doing so could cause a fire or environmental damage. Follow the collection that easily become hot.
procedures as specified by your local authority. • Charging on surfaces that can easily become hot, such as a car dashboard.

Do not use anything other than the specified secondary ◆ When charging with incandescent lighting, halogen lamps, or other lighting sources
WARNING battery. that easily become hot, place the watch at least 50 cm (20 in.) away from the source
◆ The watch will not operate if incorrect battery types are inserted. to avoid overheating.
Never use a regular silver battery. The battery could overcharge during the charging
process and burst, causing damage to the watch or injuries to the wearer.

98 99
 Troubleshooting
<Radio Signal Reception Function>
Problem Check Remedy Problem Check Remedy
• Is the home city (digital • Check the map and change the setting. • Are there objects nearby that • Avoid objects that block radio signals
display 2) set to the same • Check the map. (p. 28 ∼ 32) could block radio signals or or generate noise. Try to receive radio
reception area as your • Change the setting. (p. 42 ∼ 43) generate noise? signals by pointing the 9:00 position
current location? of the watch in the direction of the
radio signal transmitter.
• Are you attempting to receive the Find a location such as window that is
radio signal in a location far from conducive to radio signal reception
a window? and change the watch location,
Radio signals Radio signals
direction and angle. (p. 23)
cannot be • Are you moving the watch • Do not move the watch until the cannot be
received. while receiving a signal and signal has been properly received received. • Is the second hand moving at 2- • Radio waves cannot be received when
the second hand is showing (until normal hand movement is second intervals? the charge is insufficient.
RX, H, M or L? restored). (When the second hand moves in Charge the watch sufficiently by
(Reception can take from about 2 2-second intervals, the placing it in direct sunlight as
minutes to a maximum of 15 minutes.) insufficient charge warning mark indicated in “Guide to Charging
flashes in the digital display 1 and Time”. (p. 96)
the charge level indicator points
at level 0.)

100 101
 Problem Check Remedy Problem Check Remedy
Radio signals • Is the mode hand pointing to • Pull the crown out to position 1 and The time is not • Check the reception status. • If the reception status is NO,
cannot be a mode other than TME, set the mode to TME, CAL or RX-S. correct. change your location and try to
received. CAL or RX-S? receive the radio wave again. “On
Demand Reception” (p. 20)
• Check whether the daylight • In TME or WT-S mode, select
saving time is ON or OF daylight saving time ON or OF
(off). (p. 44) (off).

The watch • A slight deviance (less than 1

The time is not • Is the reference position set • If the reference position is not successfully second) may be caused by the
correct. correctly? correctly set, adjust it as indicated in received the radio internal processing of the watch.
Check the reference position. “Adjusting the Reference Position”. wave, but it deviates
(p. 14) (p. 72) slightly from the
correct time.
The second hand • Have you set the 4 a.m. • Check again the automatic
moved suddenly to automatic reception to a reception setting of the RX-S
the reception different time? (receive set) mode. (p. 66)
standby (RX)
position.

102 103
<Eco-Drive>

Problem Check Remedy Problem Check Remedy

• Is the charge level indicator • Charge the watch sufficiently until the The second hand • Is the charge level indicator • Charge the watch sufficiently until the
pointing at level 0? charge level indicator reaches level 3, is moving in 2- pointing at level 0? charge level indicator reaches the
as indicated in “Guide to Charging second intervals. fully charged level. (p. 38)
Time”. (p. 38)

The watch has • Is “ERR” displayed in • Reset the watch (p. 70) and then The hands moved • This is because the power saving
stopped. digital display 1? correct the reference position. (p. 72) forward quickly at mode was canceled when the watch
If “ERR” is displayed again, contact the moment that was exposed to light, and the hands
the store where you purchased the the watch was moved forward quickly to the current
watch or a Citizen Service Center. removed from a time. It is ready to use. (p. 92)
desk or drawer.

The watch does • Did you charge the watch • Charge the watch sufficiently, as
not work even sufficiently in sunlight? indicated in “Guide to Charging The hands or • Reset the watch. (p. 70)
after charging. Time”. (p. 96) digital displays (The internal watch system became
If the watch does not work even after are abnormal. unstable because of strong static
charging, contact a Citizen Service electricity or other external influence.)
Center.

104 105
 For correct use within the design limits of the watch, confirm the level of water-
Precautions resistance of your watch, as indicated on the dial and case, and consult the table.
WARNING: Water-resistance performance
There are several types of water-resistant watches, as shown Examples of use
in the following table.
The unit "bar" is roughly equal to 1 atmosphere.
* WATER RESIST(ANT) xx bar may also be indicated as
W.R. xx bar.

Indication Moderate exposure to Operation of the

Specifications Minor exposure to water Marine sports Scuba diving
Case (washing face, rain, etc.) water (washing, kitchen crown or button
Dial (skin diving) (with air tank)
(case back) work, swimming, etc.) with moisture visible

WATER RESIST WATER Water-resistant to

or no indication RESIST(ANT) 3 atmospheres OK NO NO NO NO
WATER
WR 50 or WATER Water-resistant to
RESIST 50 RESIST(ANT) 5 bar or
WATER RESIST(ANT) 5 atmospheres OK OK NO NO NO
WR 100/200 or WATER RESIST(ANT) Water-resistant to
WATER RESIST
100/200
10bar/20 bar or
WATER RESIST(ANT) 10/20 atmospheres OK OK OK NO NO
106 107
WARNING: Water-resistance performance • If seawater enters the watch, place the watch in a box or plastic bag and immediately take it
• Water-resistance for daily use (to 3 atmospheres): This type of watch is water-resistant to in for repair. Otherwise, pressure inside the watch will increase, and parts (crystal, crown,
minor exposure to water. For example, you may wear the watch while washing your face; buttons, etc.) may come off.
however, it is not designed for use underwater.
• Upgraded water-resistance for daily use (to 5 atmospheres): This type of watch is water- CAUTION: Keep your watch clean.
resistant to moderate exposure to water. You may wear the watch while swimming; • Leaving dust and dirt deposited between the case and crown may result in difficulty in
however, it is not designed for use while skin diving. pulling the crown out. Rotate the crown while in its normal position, from time to time, to
• Upgraded water-resistance for daily use (to 10/20 atmospheres): This type of watch may be loosen dust and dirt and then brush it off.
used for skin diving; however, it is not designed for scuba or saturated diving using helium • Dust and dirt tend to be deposited in gaps in the back of the case or band.
gas. Deposited dust and dirt may cause corrosion and soil your clothing. Clean the watch
occasionally.
CAUTION
• Be sure to use the watch with the crown pressed in (normal position). If your watch has a Cleaning the Watch
screw-lock type crown, be sure to tighten the crown completely. • Use a soft cloth to wipe off dirt, perspiration and water from the case and crystal .
• Do NOT operate the crown or button with wet fingers or when the watch is wet. Water may • Use a soft, dry cloth to wipe off perspiration and dirt from the leather band.
enter the watch and compromise water-resistance. • To clean a metal, plastic, or rubber watchband, wash away dirt with mild soap and water.
• If the watch is used in seawater, rinse with fresh water afterward and wipe with a dry cloth. Use a soft brush to remove dust and dirt jammed in the gaps in the metal band. If your
• If moisture has entered the watch, or if the inside of the crystal is fogged up and does not watch is not water-resistant, take it to your dealer.
become clear within a day, immediately take the watch to your dealer or Citizen Service NOTE: Avoid using solvents (thinner, benzine, etc.), as they may damage the finish.
Center for repair. Leaving the watch in such a state will allow corrosion to form inside.

108 109
CAUTION: Operating environment • Avoid using the watch in an environment where it may be exposed to chemicals or corrosive
• Use the watch within the operating-temperature range specified in the instruction manual. gases.
Using the watch where temperatures are outside the specified range, may result in If solvents, such as thinner and benzine, or substances containing such solvents come in
deterioration of functions or even stoppage of the watch. contact with the watch, discoloration, melting, cracking, etc. may result. If the watch comes
• Do NOT use the watch in places where it is exposed to high temperature, such as in a sauna. in contact with mercury used in thermometers, the case, band or other parts may become
Doing so may result in a skin burn. discolored.
• Do NOT leave the watch in a place where it is exposed to high temperature, such as the
glove compartment or dash-board of a car. Periodical inspections
Doing so may result in deterioration of the watch, such as deformation of plastic parts. Your watch needs inspection once in every two or three years for safety and long use.
• Do NOT place the watch close to a magnet. To keep your watch water-resistant, the packing needs to be replaced regularly.
Timekeeping will become inaccurate if you place the watch close to magnetic health Other parts need to be inspected and replaced if necessary.
equipment such as a magnetic necklace or a magnetic latch of a refrigerator door or handbag Ask for Citizen geuine parts upon replacement.
clasp or the earphone of a mobile phone. If this has occurred, move the watch away from the
magnet and reset the time.
• Do NOT place the watch close to household appliances that generate static electricity.
Timekeeping may become inaccurate if the watch is exposed to strong static electricity, such
as is emitted from a TV screen.
• Do NOT subject the watch to a strong shock such as dropping it onto a hard floor.

110 111
 • Daylight saving time on/off
■ 26. Specifications • Date: Month, date, day (fully automatic calendar until December 31, 2099)
6. Additional functions
1. Cal. No.: U60*
• Radio signal reception function (automatic reception, on demand reception, recovery
2. Type: Combination solar powered watch
automatic reception)
3. Time accuracy: Without reception (when watch is not receiving a radio signal)
• Radio wave transmitter automatic selection function (only when radio wave from
Average monthly deviation: ±15 seconds
Japan)
when used in room temperature (+5°C to +35°C / 41°F to 95°F)
• Reception on/off selection function
4. Acceptable temperature range: 0°C to + 50°C / 32°F to 122°F
• Reception standby indication function (RX)
5. Display functions
• Reception level indication function (H, M, L)
[Analog areas]
• Reception status confirmation function (H, M, L or NO)
• Home city time: Hours, minutes, seconds, 24-hour
• Automatic reception time setting function
• UTC time: Hours, minutes
• Daylight saving time on/off selection function
• Charge level display (fan-shaped display, 4 grades)
• World time alarm 1 and 2:Hours, minutes, AM/PM, city name, on/off, alarm check
• Radio wave reception display: Japan: JJY, USA: WWVB, Europe
function
(Germany: DCF77)
• Chronograph (24-hour measurement, 1/100 second units, split time measurement)
[Digital areas]
• Timer (setting range: from 1 minute up to 99 minutes, in 1-minute units)
• Home city name/world city name
Flyback function, auto return function
• World city time: Hours, minutes and seconds (switch between 12-hour and 24-hour
• World time display function
clock)
112 113
 • Time difference set by user 7. Operation time:
• Zone set function (city name display SET/OFF) • Time from a full charge until the watch stops without charging
• Home time (analog) and world time (digital) switching function : About 2.5 years (when in the power saving mode)
• LED lights : About 6 months (when not in the power saving mode)
• Power saving function 1 (The operation time may vary depending on the conditions of use, such as how
• Power saving function 2 many times the radio wave is received.)
• Reference position checking/adjustment function • Time from insufficient charge warning to watch stopping:
• Solar power function About 3 days
• Insufficient charge warning function (2-second interval movement) 8. Battery: Secondary battery 1
• Overcharging prevention function
• JIS Type-1 antimagnetic watch * Specifications may change without notice.
• Impact detection function
• Hand correction function

114 115