Technical Data

JOTAFLOOR COATING

Product description
Jotafloor Coating is a high performance, self smoothing, solvent free, seamless epoxy coating
capable of being applied at varying thicknesses to suit the final use of the floor. Jotafloor Coating
offers excellent chemical, abrasion and impact resistance.

Recommended use
Jotafloor Coating has a wide range of application uses ranging from light industrial areas to floors
requiring long lasting protection from abrasion and heavy loads. Typical areas include:
l Warehouses
l Garages
l Dairies
l Factories
l Laboratories
l Aircraft hangers
l Plant rooms
l Food manufacuring plants

Film thickness and spreading rate

Minimum Maximum Typical
Film thickness, dry (µm) 200 500 300
Film thickness, wet (µm) 200 500 300
Theoretical spreading rate (m²/l) 5 2 3.3

Physical properties
Colour Cream 908, Light grey 967, Papyrus 980, Yellow 414 and Red 2230
Solids (vol %)* 98 ± 2
Flash point >100ºC (Setaflash)
Gloss Glossy
Water resistance Excellent
Abrasion resistance Excellent
Solvent resistance Excellent
Chemical resistance Excellent Check chemical resistance values in Jotafloor chemical
resistance chart.

*Measured according to ISO 3233:1998 (E)

Surface preparation
All concrete damaged by exposure to chemicals, contaminated by any substance or unsound in
any way, shall be removed to expose sound concrete.

Coated surfaces
Clean, dry and undamaged compatible primer. Contact your local Jotun office for more information.

Other surfaces
Concrete surface preparation by using dust free captive blasting units, grinding equipment, sand
blasting or high pressure water jetting is critical to achieving the right surface profile prior to paint
application. Contact your local Jotun office for more information.

The coating may be used on other substrates. Please contact your local Jotun office for more
information.

Condition during application

The temperature of the substrate should be minimum 10°C and at least 3°C above the dew point
of the air, temperature and relative humidity measured in the vicinity of the substrate. The
moisture content in the concrete should not exceed 4 % (by weight). The coating should not be
exposed to oil, chemicals or mechanical stress until fully cured.

Application methods
Brush Stiff nylon brush
Roller Recommended
Other It is very important to pierce the coating with a spiked roller, after achieving the
desired thickness, to avoid air bubbles.

Application data
Mixing ratio (volume) 2 parts Comp. A (base) to be mixed thoroughly with 1 part Comp. B
(curing agent). NO PART MIXING
Mixing Use a slow speed drill and mixing paddle. Pour the full contents of
the mixed material onto the floor immediately after mixing is
completed.
Pot life (23°C) Jotafloor Coating Comp. B (20) 10 min. (30 min. after poured on to
the floor).
Jotafloor Coating Comp. B (40) 20 min. (45 min. after poured on to
the floor).
Thinner/Cleaner Jotun Thinner No. 17
Note This product should be applied by a trained specialist. Jotun can offer
a list of Licensed Applicators on request to your local Jotun office.

JOTAFLOOR COATING Page 2

Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of
coats, and will be affected correspondingly. The figures given in the table are typical with:
* Good ventilation (Outdoor exposure or free circulation of air)
* Typical film thickness
* One coat on top of inert substrate
Curing agent Comp. B (20):

Substrate temperature 15°C 23°C 40°C

Surface dry 6h 3h 2h
Through dry 24 h 15 h 6h
Cured 10 d 7d 3d
Dry to recoat, minimum 24 h 15 h 6h
1
Dry to recoat, maximum 72 h 48 h 30 h

Curing agent Comp. B (40):

Substrate temperature 15°C 23°C 40°C
Surface dry 8h 5h 2h
Through dry 32 h 20 h 8h
Cured 12 d 9d 3d
Dry to recoat, minimum 32 h 20 h 8h
1
Dry to recoat, maximum 96 h 72 h 36 h

1 The surface should be free from chalking and contamination prior to application. If the
maximum dry to recoat time is exceeded, please contact Jotun Paints for advice.

The given data must be considered as guidelines only. The actual drying time/times before
recoating may be shorter or longer, depending on film thickness, ventilation, humidity, underlying
paint system, requirement for early handling and mechanical strength etc. A complete system can
be described on a system sheet, where all parameters and special conditions could be included.

Typical paint system

Jotafloor Sealer 1 x 50 µm (Dry Film Thickness)
Jotafloor Coating 1 x 300 µm (Dry Film Thickness)
or
Jotafloor Solvent Free Primer 1-2 x 100 µm (Dry Film Thickness)
Jotafloor Coating 1 x 300-500 µm (Dry Film Thickness)
Note: Thickness of the finished system will vary depending on use of the finished floor. Consult
your local Jotun Office for advice.
Other systems may be specified, depending on area of use

Storage
The product must be stored in accordance with national regulations. Storage conditions are to
keep the containers in a dry, cool, well ventilated space and away from source of heat and
ignition.Containers must be kept tightly closed.

Handling
Handle with care. Stir well before use.

JOTAFLOOR COATING Page 3

Packing size
13 l. Comp. A (base) and 6.5 l. Comp. B (curing agent).
2.6 l. Comp. A (base) and 1.3 l. Comp. B. (curing agent).
Packing may vary from country to country according to local requirements.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated
conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should
immediately be removed with suitable cleanser, soap and water. Eyes should be well flushed with
water and medical attention sought immediately.

For detailed information on the health and safety hazards and precautions for use of this
product, we refer to the Material Safety Data Sheet.

DISCLAIMER
The information in this data sheet is given to the best of our knowledge based on laboratory testing and
practical experience. However, as the product is often used under conditions beyond our control, we
cannot guarantee anything but the quality of the product itself. We reserve the right to change the
given data without notice.

Head Office & Nordic Europe Middle East South East Asia
Jotun Paints Jotun Paints (Europe) Ltd. Jotun U.A.E Ltd. LLC. Jotun (Singapore) Pte. Ltd.
P.O. Box 2021 Stather Road, Flixborough Al Quoz Industrial Area No 11-15, Sixth Lok Yang
N-3248 Sandefjord North Lincolnshire DN15 8RR P.O Box 3671 Road
Norway United Kingdom Dubai U.A.E Jurong
Phone + 4 7 3 3 4 5 7 0 0 0 Phone + 4 4 1 7 2 4 4 0 0 0 0 0 Phone + 9 7 1 4 3 3 9 5 0 0 0 Singapore 628 111
Fax +47 33 46 46 13 Fax +44 172 44 00 100 Fax +971 4 3 38 06 66 Phone + 6 5 6 2 6 5 4 7 1 1
Fax +65 6265 7484

Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your
nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com

ISSUED 13 FEBRUARY 2002 BY JOTUN PAINTS

THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED

JOTAFLOOR COATING Page 4