SPEC. SHEET No.
TM-100ZT-1-00014/T-01
DATE April, 2016
TADANO CARGO CRANE
MODEL:TM-ZT1004H
CRANE SPECIFICATIONS
MAXIMUM LIFTING CAPACITY 10,000 kg at 1.4 m (8-part line)
CRANE CAPACITY 4,900 kg at 3.1 m (4-part line)
BOOM Four-sectioned, fully powered partly synchronized telescoping boom
of pentagonal box construction
Retracted length ---------------- 4.31m
Extended length ---------------- 12.91m
Extending speed ---------------- 8.6 m / 34s
Elevation--------------------------- Elevated by a double-acting
Hydraulic cylinder
Elevating speed ----------------- 1o to 82o / 17 s
Boom point ----------------------- 4 sheaves
WINCH Hydraulic motor driven Spur gear speed reduction, provided with
mechanical brake and cable follower
Single line pull --------------------14.72 kN {1,500 kgf}
Single line speed --------------- 44 m/min (at 4th layer)
Wire rope
Diameter x length --------- 10 mm x 80 m
Breaking strength --------- 73.5 kN {7,500 kgf}
Construction ---------------- 7 x 7 + 6 x Fi(29)
Hook block ----------------------- 4 sheaves
HOOK STOWING DEVICE Mechanically stowed beneath boom top portion
Specifications are subject to change without notice.
-1-
SPEC. SHEET No.TM-100ZT-1-00014/T-01
SLEWING Hydraulic motor driven Worm gear speed reduction
o
Continuous 360 full circle slewing on ball bearing slew ring
Automatic slewing lock
Slewing speed ------------- 2.2 min-1 {rpm}
OUTRIGGERS Hydraulically extended sliders and hydraulically extended jacks
Integral with crane frame Power up and down
Extended width ----------- Min. 2,300 mm
Mid. 3,900 mm
Max.5,200 mm
HYDRAULICS Hydraulic pump -------------------- Single gear pump
Hydraulic motors ------------------ Axial piston type for winch
Axial piston type for slewing
Control valves ---------------------- Multiple control valves with integral
safety valve
Oil tank capacity ------------------- approx. 90 L
SAFETY DEVICES Load meter
Load indicator
Over-winding alarm
Anti-two-block device
Hook safety latch
Hydraulic safety valves, check valves and holding valves
Level gauge
CRANE MASS Approx. 2,760 kg (except mounting parts)
NOTE : Operating speeds of the crane are guaranteed under the condition that the pump
delivery is 60 L/min.
-2-
SPEC. SHEET No.TM-100ZT-1-00014/T-01
RATED LIFTING CAPACITIES IN KILOGRAMS
Crane Strength Rated Capacities
Load 4.31 m Load 7.19 m Load 10.05 m Load 12.91 m
Radius Boom Radius Boom Radius Boom Radius Boom
1.4 m 2.25 m 4.5 m 4.5 m
10,000 6,000 3,000 3,000
and below and below and below and below
1.85 m 8,000 3.1 m 4,900 5.0 m 2,900 5.0 m 2,650
2.25 m 6,000 3.5 m 4,200 6.0 m 2,200 6.0 m 2,200
3.1 m 4,900 4.0 m 3,700 7.0 m 1,800 7.0 m 1,800
3.5 m 4,200 4.5 m 3,300 8.0 m 1,550 8.0 m 1,500
4.06 m 3,650 5.0 m 2,900 9.0 m 1,350 9.0 m 1,300
6.0 m 2,200 9.8 m 1,200 10.0 m 1,100
6.94 m 1,800 11.0 m 950
12.66 m 700
NOTES : 1. The above numerical values of total rated loads are based on crane strength only.
The total rated loads based on stability may lower than those in the above table
depending on the loading conditions and the types of the chassis.
2. Rated Lifting Capacities in these tables depend on condition that crane is set level
on firm level ground.
3. The mass of the hook (90 kg), slings and all similarly used load lifting devices must
be added to the mass of the load.
4. For boom lengths not shown, use the rated lifting capacity of next longer boom.
5. 10.05 m boom means mark on 3rd boom section side plate is half seen.
6. When the lifting load is heavier than 6,000kg, number of part lines must be 8. In
case of 6,000kg or less, number of part lines must be 4. Load per line must not
surpass 14.7kN{1,500kgf}.
-3-
SPEC. SHEET No.TM-100ZT-1-00014/T-01
WORKING RANGE
NOTE: The above lifting heights and boom angles are based on a
straight (unladen) boom, and allowance should be made for
boom deflection obtained under laden conditions.
-4-
SPEC. SHEET No.TM-100ZT-1-00014/T-01
DIMENSIONS
GENERAL DATA FOR SUITABLE TRUCKS
Gross vehicle mass (including crane mass) --- 25,000 kg or more
P.T.O. torque -------------------------------------------- 180 N.m{18.4 kgf.m} min.
P.T.O. revolution --------------------------------------- Approx. 1,200 min-1{rpm} max.
Width for crane mounting --------------------------- Approx. 1,000 mm min.
Frame ---------------------------------------------------- Weight distribution and frame strength
should be calculated for each truck
Frame width range (inside to outside) ----------- Approx. 610 to 940 mm
Frame height (ground to frame top) -------------- Approx. 1,300 mm max.
(Height of crane mounting base can be changed
by combination of jack floats and crane bases)
-5-
