Boomer XL3 D face drilling rig

Three-boom tunneling drill rig for large sized underground tunnels and
cross sections, with maximum coverage area 178 m2

1
 A giant of high
penetration
Boomer XL3 D is a high efficient three-boom pilot-hydraulic controlled face drill-
Standard advanced and powerful water-
cooled Deutz engine, 6-cylinder, 173 kW
Service basket also equipped with FOPS
approved protective roof, which gives the
Maintenance-friendly design makes the
service work safe and easy. All service
ing rig, fulfilling all range large site underground applications with high productiv- with Stage IIIA emission operator a safer operation environment points are reachable from ground level

ity and ecofriendly design.

Main benefits
Robust BUT 35 heavy-duty boom with accurate
New designed boom bracket enlarges parallel holding in all directions and 360° feed
the coverage area, the height of which is up roll-over for full coverage of the tunnel face
to 12.4-13.1 m

Reliable and easy maintainable COP Three rock drills COP 1638HD+, COP 1838HD+,
1838HD+ rock drill with high reputation. and COP 2238HD+ with high reputation are avail-
able for various application demands. FOPS approved protection roof and optional
Advanced and powerful water-cooled cabin gives you a more comfortable operation
environment
Deutz engine, 173 kW with Stage IIIA
emission.

DCS 2 pilot hydraulic control system.

DCS2 pilot-hydraulic controlled drilling system-
with high reliability, easy maintenance and easy
FOPS protective roof or cabin can move trouble shooting
upwards 1100 mm to have good vision for
the operator.

Rigid heavy-duty BMH 6000 series feed for

medium-sized and large drill application

Sturdy carrier with imported large power

2 173 kW 6-cylinder, low- emission diesel 3
engine
 Technical specifications

All for your high performacen and safe operation Rock drill
COP 1638HD+ COP 1838HD+ COP 2238HD+ • Frequency..................................................................................................... 50–60 Hz

With mature engineering solution, solid experiences base and genuine components Shank adapter R38/T38 R38/T38 R38/T38 • Starting method......................................................................................... star/delta
Hole over drill center 88 mm 88 mm 88 mm • Thermal overload protection for electric motors
Length without
shank
1 008 mm 1 008 mm 1 008 mm • Digital voltmeter/amperage/percussion hour meter in electric
Impact power 16 kW 18 kW 22 kW
cabinet
Impact rate 60 Hz 60 Hz 73 Hz • Phase sequence indicator
+ Drilling system Hydraulic pressure 200 bar 230 bar 250 bar • Earth fault indicator
The reliable drilling system includes various functions to ensure high efficient Rotation system Separate rotation Separate rotation Separate rotation • Battery charger
working, such as collaring automatics, rotation pressure controlled feeding Rotation speed 0-340/0-215 rpm 0-340/0-215 rpm 0-340/0-215 rpm • Transformer......................................................................................................... 12 kVA
(RPCF), excellent anti-jamming function and big hole drilling kit. Rotation torque, max 640/1 000 Nm 640/1 000 Nm 640/1 000 Nm
• Cable reel, diameter..................................................................1 020/1 800 mm
Lub. air consump.
5 l/s 5 l/s 5 l/s • Limit switch for cable reel
at 2 bar
Water consumption 40-120 l/min 40-120 l/min 40-120 l/min • Dual controls for cable reel
Weight 175 kg 175 kg 175 kg
Sound level <106 dB(A) <106 dB(A) <106 dB(A)
Air system
• Electric driven piston compressor............................. Atlas Copco LE 10

Feed • Capacity, 7 bar.................................................................................................... 15.7 l/s

• Electric motor...................................................................................................... 7.5 kW
+ FAM III (Feed Angle Measurement) BMH 6800
Total length
BMH 6814
5 882 mm
BMH 6816
6 502 mm
BMH6818
7 102 mm
BMH 6820
7 677 mm • Air pressure gauge
Epiroc FAM III system guarantees you high precision drilling position, including: Drill rod length 4 310 mm 4 920 mm 5 530 mm 6 100 mm
− Drill plan and boom position display on screen Hole depth 4 048 mm 4 668 mm 5 268 mm 5 843 mm Water system
− Import/Export of drill plan data to screen via USB stick Weight, incl. drill 670 kg 705 kg 745 kg 775 kg • Electric driven water booster pump Lowara 22SV12F150
− Underground Manager drill plan design software Feed force 22 kN 22 kN 22 kN 22 kN
• Water booster pump max capacity at 17 bar....................... 300 l/min
− Manual drilling • Min water inlet pressure at 300 l/min................................................... 2 bar
− Manual positioning Boom • Electric motor....................................................................................................... 15 kW
• Boom .......................................................................................................................BUT 35 • Water pressure gauge
• Feed extension ......................................................................................... 1 800 mm • Water flow guard
+ Operator station • Boom extension ....................................................................................... 1 600 mm
The Boomer XL3 D is designed with safty and ergonomics in mind. Operators • Parallel holding ...........................................................................................complete Carrier
can work under safe FOFS approved protection roof with optional cabin. • Feed roll-over ......................................................................................................... 360° • Engine.................................... Deutz TCD 2013 L06 2V Stage IIIA / Tier 3
Operators’ platform lift system raises the operators’ platform 1100mm from stan- • Max. lifting angle ....................................................................................... +70°/–30° • Power rating at 2 300 rpm.................................................... 173 kW (235 hp)
dard height, assists the operator visibility when drilling. Easy access to hydraulic • Boom swing angle L/R ..................................................................................... ±45° • Torque at 1 500 rpm..................................................................................... 907 Nm
parts under the operators’ platform makes maintenance a lot easier. • Weight, Boom only..................................................................................... 2 920 kg • Four-wheel drive
• Hydrostatic power steering system
• Hydrodynamic transmission...................................................... Clark 32 000
Control system
• Front axle................................................................................................... Dana 37R116
• Direct hydraulic Control System, DCS 2
• Rear axle .................................................. Dana 213/169 with ± 7° oscillation
• Basic functions such as anti-jamming included
• Manual differential lock on front axle
• Tyres ............................................................................. 14.00 x R24 Michelin XKA

A comprehensive
Hydraulic system
• Clearance outside axles........................................................................................ 15°
• Hydraulic pumps......................... 3 separate units, one for each boom
• Hydraulic jacks, front .............................. 2 extendable with large plates

service offering • Pumps unloaded at start

• System pressure, max................................................................................. 210 bar
• Hydraulic jacks, rear..................................................................................................... 2
• Service brakes........................................................................ 2 separate circuits
• Hydraulic oil tank, volume min/max............................................ 470/755 l • Emergency and parking brakes................................................................ SAHR
Even the best equipment needs to be • Low oil level indicator • Fuel tank, volume.................................................................................................. 150 l
serviced regularly to make sure it sustains
• Oil temperature gauge on oil tank • Electric system......................................................................................................... 24 V
peak performance. An Epiroc service • Batteries.......................................................................................................... 2 x 120 Ah
• Electrical oil filling pump
solution offers peace of mind, maximizing • Tramming lights, LED..................................... ........................................... 8 x 40W
• Filtration................................................................................................................... 10 μm
availability and performance throughout
• Mineral hydraulic oil • Working lights, LED...................................................................................... 8x80W
the lifetime of your equipment. We focus
• Illuminated stairs for platform, LED........................................ ........ 2 x 40W
on safety, productivity and reliability.
• Silencer
Drilling system
• Fire extinguisher............................................................................................... 2 x 6 kg
By combining genuine parts and an Epiroc • Rock drill lubrication warning kit
• Gradeability at max. load on drive wheels................................................ 1:4
service from our certified technicians, we • Beacon and reverse alarm
safeguard your productivity – wherever Electric system
• Horn
you are. • Total insalled power ............................................................. 200 kW
• Hand throttle
• Main motors.................................................................................................. 3 x 55 kW
• Voltage......................................................................................................... 400–690 V

4 5
 Technical specifications Technical specifications
Optional equipment Measurements

Side view
Drifter rods
Dimension Min. hole diameter
mm R38-HEX 35-R32 45

1 100
T38-HEX 35-R32 45 Platform lift
T38-HEX 35-R32 Speedrod 45
7 102
R38-HEX 35-SR35 Speedrod 45 Roof lift
T38-HEX 35-SR35 45
T38-Rnd 39-SR35 45
T38-HEX 35-R35 48

3 789
T38-HEX 35-R35 Speedrod 48
T38-Rnd 39-R35 48
T38-Rnd 39-R35 Speedrod 48

396
Shank adapters 3 591 4 200
Shank adapters
Tramming length 16 565 (BMH 6 818)
Thread Diameter Length Part No. Thread Diameter Length Part No.
mm R38 38 435 404-09101,00 mm R38 55 170 304-0055,00
T38 38 435 435-09101,00 T38 55 190 335-0055,00
T38 38 525 435-09103,00*
Coverage area
*Intended for RAS and extension drilling with BSH 110

Lock-out angle 2° Lock-out angle 2°

Extension rods for injection drilling/RAS Parallel holes Parallel holes
Dimension Min. hole diameter Coverage area: 160m2 Coverage area: 178m2
mm R32 Speedrod 51 (With 3 x BUT 35M) (With 3xBUT 35L)
T38 Speedrod 64
2 676 2 676
2 267 2 267

12 656
12 392

13 108
11 931
Drilling System Hydraulic system
• Hole blowing kit, excluding CSA approved air receiver (CE) • Biodegradable hydraulic oil

5 895

5 895
Feed Carrier

2 506

2 506
2 248

2 248
245

245
• Extension drilling set BSH 110 • Exhaust system catalyser
• Top-mounted feeds • Exhaust system particle filter
12 990 14 188
• Spotlight LED 70W, left/right
14 982 16 024
Boom
• BUT 35L (SP3 should be used if needed) Electrical system
• Automatic boom lubrication system, rear part of boom • Electric cable, Buflex
• Feed Angle Measurement system (FAM I) • Plug
• Feed Angle Measurement system with hole depth • Socket
measurement (FAM II) Dimensions Noise and vibration
• Switch gear
mm Width 2 926
• Feed Angle Measurement system with hole depth Operator sound pressure level in canopy, drilling,
• Connector Height roof down 3 089 free field (ISO 11201)
104±6 dB(A) re 20uPa
measurement and drilling plan (FAM III)
• Electric outlet for accessories, 3-phase, max 16 A, 690 V Height roof up 3 789
Operator sound pressure level working close to
• 3-phase outlets 32 A/16 A, with extra transformer 15 kVA, Length with BMH 6818 feeds 16 565 104±6 dB(A) re 20uPa
machine, drilling, free field
Air system
1-phase outlets 10 A Ground clearance 396
• Extra compressor LE5 additional 8 l/s at 8 bar (used for Sound power level (ISO 3744), drilling, free field 130 dB(A) re 1pW
Turning radius 12 100/6 700
hole blowing kit, manual lubrication kit, and air-water
Miscellaneous Vibration levels standing, canopy (ISO 2631-1) 0.1± 0.15 m/s^2
outlet on platform)
• Service platform, SP2 or SP3
• FOPS-approved protective roof for service platform Weight
Water system
gross weight Recommended cable size and length
• Water hose reel, diameter 1 800 mm • Water and air outlet in service platform basket
kg Total 42 000 Voltage Type Dimension, mm2 Diameter,mm Length,m
• Dual controls for hose reel • Hydraulic Swellex pump
Boom side 32 000 400 V Buflex 4x185+3G35 55 100
• Water hose, diameter 2”, lenght 70 m at 70% filling rate • Holder for spare drill rods
Engine side 10 000 440–500 V Buflex 3x150+3G25 52 110
• Rig washing kit 550 V Buflex 3x120+3G25 46 135
• Manual lubrication system 690 V Buflex 3x95+3G16 42 150
Tramming speed 1 000 V Buflex 3x50+3G10 32 250
km/h On flat ground (rolling resistance 0.05) >17
G = Protection yellow/green
On incline 1:8 >6
6 Recommendations are given for surrounding temperature of 40 °C and up to a height 7
of 2 000 m.
epiroc.com
commitment drives us to keep moving forward.
Performance unites us, innovation inspires us, and

Count on Epiroc to deliver the solutions you need to

Inspired by innovation.

succeed today and the technology to lead tomorrow.

United in performance.
9869 0034 01 2018-05, Nanjing, China. Legal Notice © Copyright 2018, Epiroc (Nanjing) Mining & Construction Equipment Ltd., Nanjing, China. All product names in this publication are trademarks of Epiroc. Any unauthorized
use or copying of the contents or any part thereof is prohibited. Illustrations and photos may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are
subject to change without notice. Consult your Epiroc Customer Center for specific information.