BILL OF QUANTITY

Name of Work:- Annual zonal rate contract for petty electrical works of Hostel area. (Zone I)
(2017-18).
Name of agency
Sl.N Description Qty Unit Rate Amount
o.
Wiring
1 Wiring for light point/fan point/exhaust fan point/call bell
point with 1.5 sq.mm FRLS PVC insulated copper conductor
single core cable in surface / recessed steel conduit, with
modular switch, modular plate, suitable GI box and earthing
the point with 1.5 sq.mm FRLS PVC insulated copper
conductro single core cable etc. as required.

a) Group 'A' 50 Pts 0.00

b) Group 'C' 50 Pts 0.00
2 Rewiring of light point/fan point/ exhaust point/ call bell point
with 1.5 sq.mm. PVC insulated flexible copper conductor and
earth wires (FR) cable in existing surface/recessed conduit I/c
dismantling as reqd.

a) Group 'A' 50 Pts 0.00

b) Group 'C' 10 Pts 0.00
3 Supplying & drawing following sizes of FRLS PVC insulated
copper conductor single core cable in / on the existing
surface / recessed, PVC / steel conduit as reqd.
a) 1 x 1.5 Sq.mm.. 50.00 Mtr. 0.00
b) 2 x 1.5 Sq.mm.. 50.00 Mtr. 0.00
c) 3 x 1.5 Sq.mm.. 300.00 Mtr. 0.00
d) 3 x 2.5 Sq.mm.. 100.00 Mtr. 0.00
e) 2 x 4 Sq.mm.. 50.00 Mtr. 0.00
f) 3 x 4 Sq.mm.. 150.00 Mtr. 0.00
g) 4 x 4 Sq.mm.. 50.00 Mtr. 0.00
h) 6 x 4 Sq. mm. 50.00 Mtr. 0.00
i) 2 x 6 Sq.mm.. 50.00 Mtr. 0.00
j) 3 x 6 Sq.mm.. 100.00 Mtr. 0.00
k) 4 x 6 Sq.mm.. 20.00 Mtr. 0.00
l) 6 x 6 Sq. mm. 50.00 Mtr. 0.00
4 Supplying & drawing following sizes of FRLS PVC insulated
copper conductor single core cable in / on the existing
surface / recessed, PVC / steel conduit as reqd.
a) 2 x 10 Sq.mm.. 25.00 Mtr. 0.00
b) 4 x 10 Sq.mm.. 25.00 Mtr. 0.00
c) 2 x 16 Sq.mm.. 25.00 Mtr. 0.00
d) 4 x 16 Sq.mm.. 25.00 Mtr. 0.00
5 Supply and drawing PVC insulated copper conductor 3 core
cable round cable of following size including connection etc.
Complete as required.
a) 1.5 sq.mm.. 50.00 Mtr. 0.00
b) 2.5 sq.mm 50.00 Mtr. 0.00
c) 4.0 sq.mm 50.00 Mtr. 0.00
6 Supply and drawing of telephone wire of 2 pair 0.50 mm dia 300.00 Mtr. 0.00
copper conductor FRLS PVC insulated unsheathed twisted wire
in existing / surface concealed conduit as reqd. including
numbering and connecting the wires at both the ends.

7 S & F of following size of steel conduit along with the

accessories in surface/recess I/c painting in case of surface
conduit or cutting the wall and making good the same in case
of recessed conduit as reqd.

a) 20 mm 16 SWG 50.00 Mtr. 0.00

b) 25 mm 16 SWG 50.00 Mtr. 0.00

Page 1
c) 32 mm 16 SWG 20.00 Mtr. 0.00
d) 40 mm 14 SWG 20.00 Mtr. 0.00
8 S & F metal box of following sizes ( nominal size ) on surface or
recess with suitable size of 3 mm phenolic laminated sheet
cover in the front I/c painting etc as reqd.

a) 75 mm x 75 mm x 60 mm deep 30 Nos. 0.00

b) 100 mm x 100 mm x 60 mm deep 30 Nos. 0.00
c) 180 mm x 100 mm x 60 mm deep 30 Nos. 0.00
d) 200 mm x 150 mm x 60 mm deep 30 Nos. 0.00
e) 200 mm x 250 mm x 75 mm deep 30 Nos. 0.00
9 S& F following size/module, GI box along with modular base
and cover plate for modular switches in recess as required.
a) 1/2 module (1 or 2 module) 50 Nos. 0.00
b) 3 module 50 Nos. 0.00
c) 4 module 50 Nos. 0.00
d) 6 module 50 Nos. 0.00
e) 8 module 20 Nos. 0.00
f) 12 module 10 Nos. 0.00
g) 18 module 10 Nos. 0.00
10 S & F following size modular base and cover plate for following
modular metal boxes etc as required.
a) 1/2 module (1 or 2 module) 50 Nos. 0.00
b) 3 module 50 Nos. 0.00
c) 4 module 50 Nos. 0.00
d) 6 module 50 Nos. 0.00
e) 8 module 20 Nos. 0.00
f) 12 module 10 Nos. 0.00
g) 18 module 10 Nos. 0.00
11 Supplyand & fixing following rating piano type switch
/socket /fan regulator on the existing switch box/cover I/c
connection etc. as reqd.
a) 5/6 amp one way switch 300 Nos. 0.00
b) Two way 5/6 amp switch 10 Nos. 0.00
c) 15/16 amp one way switch 150 Nos. 0.00
d) 3/5 pin 5/6 Amp. Socket outlet. 150 Nos. 0.00
e) 6 pin 15/16 Amp. Socket outlet 100 Nos. 0.00
f) Fan regulator socket type rotary step 300 Nos. 0.00
g) Batten Holder/Angle Holder bakelite type 50 Nos. 0.00
h) Ceiling rose 3-Pin, 5A 50 Nos. 0.00
i) Bell push 6 A one way. . 20 Nos. 0.00
12 Supplyand & fixing following modular switch/ socket on the
existing modular plates & switch box including connection but
excluding modular plate etc. as reqd.
a) 5/6 Amp one way switch 300 Nos. 0.00
b) 3 Pin 5/6 Amp. socket outlet 150 Nos. 0.00
c) 15/16 Amp. one way switch 100 Nos. 0.00
d) 6 Pin 15/16 Amp. socket outlet. 100 Nos. 0.00
e) Modular Type Electronic Fan regulator 300 Nos. 0.00
f) Telephone socket outlet 20 Nos. 0.00
g) TV antenna socket outlet 10 Nos. 0.00
h) Modular type blanking plate. 300 Nos. 0.00
i) Modular bell push 6 A one way. . 20 Nos. 0.00
13 Supplying and fixing call bell / buzzer suitable for single phase, 10 Nos. 0.00
230 volts, complete as required.
14 Supply, fixing, connecting & commissioning of 3 pin Plug top 6 20 Nos. 0.00
Amp. as reqd. Anchor
15 Supply fixing connecting & commissioning of 3 pin Plug top 16 10 Nos. 0.00
Amp. as reqd. Anchor

Page 2
16 Supply, Installation, testing & commissioning of AC ceiling fan
of following sweeps, alluminium die cast body , copper
wound, double bearing, less 70 watts 220 volts 50 Hz without
regulator I/c wiring the down rods of standard length up to 30
cm with 1.5 sq.mm. PVC insulated copper conductor single
core cable etc as reqd. ( ISI marked.)

a) 1200 mm make_Bajaj Kassels/or equivalent approved make. 30 Nos. 0.00

b) 1400 mm make_Bajaj Kassels/or equivalent approved make. 5 Nos. 0.00
17 Supplying, fixing, connecting, commissioning & testing of wall 5 Nos. 0.00
mounted fan 400mm (16") sleek model metal body with rag
bolts etc. as reqd.
18 Supply, Installation,testing and commissioning of exhaust fan
of following sizes,1Ǿ AC power supply,50 Hz in the existing
opening I/c connection,rag bolts complete as reqd.

a) 300mm 6_pole 5 Nos. 0.00

b) 380 mm 6_pole 2 Nos. 0.00
c) 450 mm 6_pole 2 Nos. 0.00
19 Supply and fixing of louver for exhaust fan of following sizes
with rag bolts as reqd.
a) 12" 2 Nos. 0.00
b) 15" 2 Nos. 0.00
c) 18" 2 Nos. 0.00
20 Supplying & fixing, connecting & commissioning industrical 15 Nos. 0.00
type metal clad plug top 20 Amp. 2P+E . (make_ Legrand).
21 Supplying & fixing, connecting & commissioning industrical 15 Nos. 0.00
type metal clad socket 20 Amp .(20 A 2P+E)(make_ Legrand).

22 S & replacement of Hotal key fob switch 20Amp. (Cat No. 5722 2 Nos. 0.00
44)with key fob complete, I/c connecting and commissioning
etc reqd. make legrand.
23 S & replacement of key fob (Cat No. 5722 59)suitable for 2 Nos. 0.00
Hotal key fob switch 20Amp. as reqd. .(Legrand/ cabtre)
24 Supplying and fixing 20 amps 240 volts, SPN industrial type, 10 Nos. 0.00
socket outlet with 2 pole earthing metal enclosure, metal plug
top,along with 20 amps, 10 KA,SP MCB on surface or in recess
with chained cover for the socket outlet and complete as reqd.

25 Supplying and fixing 20 amps 415 volts, TPN industrial type, 2 Nos. 0.00
socket outlet with 4 pole earthing metal enclosure, metal plug
top,along with 20 amps, 10 KA,TP MCB on surface or in recess
with chained cover for the socket outlet and complete as reqd.

26 S & F 3 mm thick phenolic laminated sheet on existing board 1000.00 Sq.in. 0.00
with brass screw & cup washer etc as reqd.
27 S & F bakelite sheet 5 mm thick complete with required nuts & 100.00 Sq.in. 0.00
bolts as reqd.
MCB,DB & SWITCH FUSE UNITS
28 S & F MCB of following pole and rating 240/415 volts 'C' series
in the existing MCB DB complete with connection, testing &
commissioning etc as reqd. ( legrand)
a) Single Pole 6 amp to 32 amp 80 Nos. 0.00
b) Single Pole & Neutral 6 amp to 32 amp 20 Nos. 0.00
c) Triple Pole 6 amp to 32 amp 10 Nos. 0.00
d) Triple pole & Neutral 6 amp to 32 amp 10 Nos. 0.00
e) SP MCB Blanking plats 100 Nos. 0.00
29 Supply and fixing, testing & commissioning of RCCB having
sensitivity current 300 MAmp following pole and rating as
reqd.
a) 25 to 32amp DP RCCB, 5 Nos. 0.00

Page 3
b) 40 amp DP RCCB 5 Nos. 0.00
c) 25 amp triple pole, RCCB 2 Nos. 0.00
d) 40 amp triple pole RCCB 2 Nos. 0.00
e) 63 amp four pole, RCCB 2 Nos. 0.00
30 Supply and fixing, testing & commissioning MCB of following
pole and rating 240/415 volts 'C' curve 10kA in the existing
MCB DB complete as reqd. ( legrand or equivalent make)

a) Single Pole 40 amp to 63 amp 5 Nos. 0.00

b) Single Pole & Neutral 40 amp to 63 amp 5 Nos. 0.00
c) Triple Pole 40 amp to 63 amp 2 Nos. 0.00
d) Triple pole & Neutral 40 amp to 63 amp 2 Nos. 0.00
31 S & F metal enclosure suitable for DP/FP MCB/ ELCB on 5 Nos. 0.00
surface or recessed etc as reqd.
32 P & F S&F following ratings and braking capacity and 3 pole
MCCB unit in existing panel board i/c driling and making
connections etc as reqd.
a) 125 Amp. 16KA 1 No. 0.00
b) 150 Amp. 16KA 1 No. 0.00
c) 200 Amp. 25KA 1 No. 0.00
d) 315 Amp. 35KA 1 No. 0.00
e) 200 Amp. 36KA 1 No. 0.00
f) 250 Amp. 36KA 1 No. 0.00
33 Supplying and fixing following way, SPN MCB DB (single pole
and neutral, sheet steel, MCB distribution board), 240 Volts,
on surface/ recess, complete with tinned copper bus bar,
neutral bus bar, earth bar, din bar, interconnections, powder
painted including earthing etc.as required. (But without
MCB/RCCB/Isolator).

a) 6 -way, D.Door 2 Nos. 0.00

b) 8 -way, D.Door 2 Nos. 0.00
c) 12 -way, D.Door 2 Nos. 0.00
d) 16 -way, D.Door 2 Nos. 0.00
34 Supplying and fixing following way, horizontal type triple pole
and neutral, sheet steel, MCB distribution board, 415 Volts, on
surface/ recess, complete with tinned copper bus bar, neutral
bus bar, earth bar, din bar, interconnections, powder painted
including earthing etc.as required. (But without MCB/ RCCB/
Isolator).

a) 4 way (4 + 12), Double door 2 Nos. 0.00

b) 6 way (4 + 12), Double door 2 Nos. 0.00
c) 8 way (4 + 12), Double door 2 Nos. 0.00
35 Supplying and fixing following way, vertical type triple pole
and neutral, sheet steel, MCB distribution board, 415 Volts, on
surface/ recess, complete with tinned copper bus bar, neutral
bus bar, earth bar, din bar, interconnections, powder painted
including earthing etc.as required. ( But without
MCB/RCCB/Isolator).

a) 4 way (4 + 12), Double door 2 Nos. 0.00

b) 8 way (4 + 12), Double door 2 Nos. 0.00
c) 12 way (4 + 12), Double door 1 No. 0.00
36 S&F following rating , TPN switch fuse unit (SFU) 415 / 500 volt
(open execution type) with HRC fuse i/c connections, earthing
the body etc. as reqd.
a) 63 Amp. 2 Nos. 0.00
b) 125 Amp. 2 Nos. 0.00
c) 200 Amp. 1 No. 0.00
d) 315 Amp. 1 No. 0.00
37 Supply and fixing of following rating HRC fuses din type in
existing SFU as reqd.

Page 4
a) 63 Amp, 100 Amp. 5 Nos. 0.00
b) 125 Amp. 5 Nos. 0.00
c) 200 Amp. 5 Nos. 0.00
38 Supply and fixing of following rating HRC fuses Bolted type in
existing SFU as reqd.
a) 100 Amps 5 Nos. 0.00
b) 200 Amps 5 Nos. 0.00
c) 315 Amps 5 Nos. 0.00
LIGHT FITTINGS & LUMINARIES
39 Supply and fixing of LED Light fixture
a) LED Batten Type fitting 9 watt make_Crompton (Cta. No. LCTL- 10 Nos. 0.00
09-CDL ) or equivalent from approved make.
b) LED Batten Type fitting 18 watt make_Crompton (Cta. No. 10 Nos. 0.00
LCTL-18-CDL ) or equivalent from approved make.
c) LED Ceiling Light 36watt,size(2X2) _Make crompton Aura (cat 3 Nos. 0.00
No.LCPL-36-CDL) or equivalent from approved make.
d) LED Ceiling Light 36 watt,size (1X4) _Make_Aura crompton (cat 3 Nos. 0.00
No. LCPL-36-CDL) or equivalent from approved make.

e) LED Ceiling Light Fitting Surface type 40 watt (1X4) 5 Nos. 0.00
make_Crompton SPAN (CAT No. LCTLRN-40-CDL) or equivalent
from approved make.
f) LED Ceiling Light 6 watt round/square shape Make_Crompton 10 Nos. 0.00
(Cat No. LCDSPL-S/R-06-CDL ) or equivalent from approved
make.
g) LED Ceiling Light 12 watt round/square shape 10 Nos. 0.00
Make_Crompton (Cat No. LCDSPL-S/R-12-CDL ) or equivalent
from approved make.
h) LED Ceiling Light 18 watt round/square shape 10 Nos. 0.00
Make_Crompton (Cat No. LCDSPL-S/R-18-CDL ) or equivalent
from approved make.
i) LED Mirror Light 7 watt Make_Crompton (LCL-07-CDL) or 10 Nos. 0.00
equivalent from approved make.
j) LED Mirror Light 14 watt Make_Crompton (LCL-14-CDL) or 5 Nos. 0.00
equivalent from approved make.
k) Bulkhead fitting CFL Type 1 X 8w Havells make (Cat No. CFL 5 Nos. 0.00
(TU) 100W GLS) or equivalent from approved make.
l) LED Bulkhead fitting 10 watt, Endura Rugby Neo - IP65, 5 Nos. 0.00
Havells make (Cat No. LHEOAOP7UZ6W010) or equivalent
from approved make.
m) Post Top Lantern 40watt make_Crompton (CatNo.LPTO-40- 5 Nos. 0.00
CDL) or equivalent from approved make.
n) Streetlight Luminaires 18 watt (Bracket type) 2 Nos. 0.00
make_Crompton (CatNo.LSTP-18-CDL) or equivalent from
approved make.
o) Streetlight Luminaires 25 watt (Bracket type) make_Crompton 2 Nos. 0.00
(CatNo.LSTP/LSTO-25-CDL) or equivalent from approved
make.
40 Supply & fixing of Luminaries (lamps) for following light fittings

a) PL-C 10 to18 watt/2 or 4Pin Make Philips or equivalent. 30 Nos. 0.00

b) PL-S 9 to 11Watt /2 or 4Pin Make Philips or equivalent. 30 Nos. 0.00
c) PL-L 18 to 36Watt/4P 1CT/25 Make Philips or equivalent 25 Nos. 0.00
d) Metal halide lamp double ended 70/150watt (MHN-TD DE 25 Nos. 0.00
70/150 Watt), make Philips or equivalent.
e) HPSV Lamps 70W with ignitor (eliptical), make_Philips or 25 Nos. 0.00
equivalent.
f) HPSV Lamps 70W Without ignitor (eliptical), make_Philips or 5 Nos. 0.00
equivalent

Page 5
g) HPSV Lamps 150W with ignitor (eliptical), make_Philips or 5 Nos. 0.00
equivalent
h) Picture lamp 40 watt pin/screw typemake_Philips or 25 Nos. 0.00
equivalent
i) LED Tube rod 20 watt Make _philips steller Bright or 50 Nos. 0.00
equivalent
j) Tube light 28 watt T5 Make_Crompton or equivalent. 10 Nos. 0.00
k) Tube light 36 watt Make_Crompton or equivalent. 10 Nos. 0.00
l) Tube light 40 watt Make_Crompton or equivalent. 10 Nos. 0.00
m) Starter 20/40 watt 300 Nos. 0.00
41 Supply, Fixing,Testing and commissioning of choke (Electronic
ballast) for following fittngs including connection etc complete
as required.
a) Electronic Choke for FL. Fitting 36W/40W, make_Philips (Type 10 Nos. 0.00
EBT136TLD240, 1 X TL) or equivalent approved make.,

b) Electronic ballast for TL fitting 1XTL36W/40W 10 Nos. 0.00

Make_Philips(Cat No. EBE (Slim) 136 TLD 240V) or equivalent
approved make.,
c) Electronic Choke for FL fitting 2 X 18/20/36/40 watt, 15 Nos. 0.00
Make_Philips (Type EBT 236/218 TLD 240) or equivalent
approved make.,
d) Electronic Choke for FL. fitting 1 X28W TL_5 , 15 Nos. 0.00
Make_Philips(Type EBT I28 TLD 240) or equivalent approved
make.,
e) Electronic Choke for FL fitting 2 X28w TL_5 , 10 Nos. 0.00
Make_Philips(Type EBT 228 TL5 240 or equivalent approved
make.,
f) Electronic Choke for PL-s/PL-c/PL-t fitting 1X7/9W-2/4P Philips 15 Nos. 0.00
make, Type EB-S 109 220-240 SH) or equivalent approved
make.,
g) Electronic Choke for PL-s/PL-c/PL-t fitting 1XPL-C/PL-T 15 Nos. 0.00
10/13/18 & PLS /11 Watt 2/4P .Make_Philips (Type EB-S
114/118 230 SH) or equivalent approved make.,
h) Choke (Copper ballast) for PL-s fitting 5/7/9/11Watt, 10 Nos. 0.00
Make_Philips(Type BPL 009X261) or equivalent approved
make.
i) Choke (Copper ballast) for HPSV/metal halide fitting 1X70W 10 Nos. 0.00
SON/MH Lamp, make_Havells (Cat No. LHBW07170036) or
equivalent approved make.,
j) Choke (Copper ballast) for HPSV/metal halide fitting 1X150W 5 Nos. 0.00
SON/MH Lamp, make_Havells (Cat No. LHBW20115036) or
equivalent approved make.,
k) Ignitors for HPSV/MH Lamp 70 to 400 watt, make_Havells or 15 Nos. 0.00
equivalent approved make.
42 Supplying,fixing, connecting & commissioning timer switch 2 Nos. 0.00
complete as reqd.For 24 hrs setting (Maxirex 4QTB) Legrandor
equivalent
43 Providing,fixing ,Testing and commissioning of timer switch for 2 Nos. 0.00
24 Hrs setting astronomical type channel mounted complete
as reqd. Make_Legrand (Alpharex 3 D21 astro, 1 Channel) or
its equvalent.

44 S&F connecting and commissioning the contactor of following

ratings and pole 25KA with magnetic release I/c providing
connecting copper/Al. Strip/ lead of suitable rating between
bus bar and contactor tapping etc. as reqd.

a) 40-45 Amp. Single pole 230V, MNX 25 (Cat No. CS94110) 2 Nos. 0.00
b) 40 Amp. Three pole 415 V,MNX 40 (Cat No. CS94190) 2 Nos. 0.00

Page 6
45 Supply & fixing of 65 mm dia.'B' class GI pole 4.5 mtr. Long for 2 Nos. 0.00
post top lantern i/c bas eplate 300 x 300 x 3mm GI reducer &
nipple for mounting the fitting with painting etc. grounting in
cement concrete 1: 3: 6 (1 cement : 3 coarse sand : 6 grade
stone aggregate 40mm nominal size 0.4mm dia x 0.5 mm high
to accomade the looping) complete as reqd.

INTERNAL REPAIR WORKS

46 Dismantling of rally fan / cabin fan/ ceiling fan from normal 10 Nos. 0.00
height and depositing in store as reqd.
47 Installation, testing and commissioning of ceiling fan 10 Nos. 0.00
with/without, including wiring the down rods of standared
length (upto 30cm)with 1.5sq.mm FRLS PVC insulated, copper
conductor, single core cable etc as required.

48 Installation of exhaust fan in the existing opening , including

making good the damage, connection, testing, commissioning
etc. as reqd
a) Upto 450 mm sweep 10 Nos. 0.00
b) 510 mm sweep 10 Nos. 0.00
49 Dismantling and refixing bakelite/ phenolic laminated sheet 1000.00 Sq.in. 0.00
upto 6mm thickness with screws and cup washers as required

50 Repairing, cleaning and replacement of damaged parts in 200.00 Nos. 0.00

existing fitting (i.e. holder, Lamp, tubes, chokes starter etc.)
complete as required.
51 Erection of wall bracket / ceiling fittings of all sizes and shapes 5 Nos. 0.00
containing upto two GLS lamps per fitting, complete with all
accessories including connection etc. As required.

52 Installation, testing and commissioning of pre-wired, 10 Nos. 0.00

fluorescent fitting / compact fluorescent fitting of all types,
complete with all accessories and tube etc. Directly on
ceiling / wall including connection with 1.5sq.mm FRLS PVC
insulated, copper conductor, single core cable and earthing
etc. as required.

53 Dismentaling, disconnecting 3x1.5/2.5/4.0/6.0/10.0 sqmm 1000.00 Mtr. 0.00

wire from existing conduit pipe casing and caping and making
role and depositing in store as reqd.
54 Dismantling the old conduit pipe of all sizes from 100.00 Mtr. 0.00
surface/recessed & making good the damages I/c filling the
holes of the surface and depositing the same as reqd.

55 Dismantling the old wood batten/PVC casing caping of all sizes 100.00 Mtr. 0.00
from surface & making good the damages I/c filling the holes
of the surface and depositing the same as reqd.

56 Fixing 20/25/32 mm steel conduit pipe with all accessories in 100.00 Mtr. 0.00
surface / recess including painting in case of surface conduit or
cutting the wall and making good the same in case of
recessed conduit as required complete. Only conduit pipe
supplied by department as reqd.

57 Dismantling of M.S./PVC box of upto size 200 mm x 250 mm x 20 Nos. 0.00

75 mm on surface/ recessed including making good and
painting with enamel paint etc as reqd
58 Fixing following size PVC/MS box on surface/recessed
including painting, making good with enamel paint etc. As
reqd.
a) Up to size 100 mm x 100 mm x 75 mm 20 Nos. 0.00
b) size exceding 200 mm x 250 mm x 75 mm 20 Nos. 0.00
59 Fixing TPN switch/DB 100/400 amp on existing frame/board 2 Nos. 0.00
I/c providing nut & bolts with washer as reqd. i/c. c & c etc. as
reqd.

Page 7
60 Locating fault in wiring rectifying removing & restoring supply 25 Nos. 0.00
the same & making good the damages etc as reqd.
61 Locating fault in the cable lines with meager etc. and rectifying 5 Nos. 0.00
removing & restoring supply the same & making good the
damages etc ( temporary) as reqd.
62 Providing 1/3 phase temporary service connection from 3 Nos. 0.00
supply source to desired place up to the lead/ cable 35
sq.mm. of 50 mtr. and disconnecting the same including to &
fro cartage. ( extension board and cable will be supplied by the
dept.)

63 Digging cable trench, lifting brick & cable and locating fault 50.00 Mtr. 0.00
and relaying the cable I/c. refilling the same as required.
64 Dismentling, lifting & removing cable of any size from trench/ 100.00 Mtr. 0.00
clamps on surface, making roll depositing the same in the
store I/c cartage etc as reqd.
65 Supply and fixing of Copper tube with coupling and washers 10 Set 0.00
geyser up to 4 ft long (set of two copper tube with nuts and
washers 4nos.) complete as required.
66 Supply & fixing 1 set (4 Nos.) of rag bolts with washer 100 Set 0.00
12x100mm suitable size for rack of network system & water
geyser as reqd.
METER /STARTERS
67 Supplying & fixing 1 or 3Ǿ with LCD display type electronic
energy meter of following rating and specification
with/without optical port existing surface including
connection complete as reqd.

a) 1P LCD Meter 5-30A with out BOX , Make_L & T (Cat no. 2 Nos. 0.00
WM101BC5DL0 ) or equivalent.
b) 1P LCD Meter 5-30A with BOX , Make_L & T (Cat no. 2 Nos. 0.00
WM101BC5DL0BOX ) or equivalent.
c) 1P LCD Meter 5-30A with Optical port + BOX ,Make_L & T (Cat 2 Nos. 0.00
no.WM101BC5DDHBOX ) or equivalent.
d) 3Ph 4 W LCD Energy Meter 5 -10 A ,240V CT op base mtg (cat 1 No. 0.00
no.WM301BC3C00)
e) 3Ph 4 W LCD Energy Meter 5 -20 A ,240V Dir base mtg 1 No. 0.00
Make_L&T Sleek(cat no.WM301BC4D20)
f) 3Ph 4 W LCD Energy Meter 10 -40 A ,240V Dir base mtg 1 No. 0.00
Make_L&T Sleek (cat no.WM301BC6D200)
g) 3Ph 4 W LCD Energy Meter 10 -60 A ,240V Dir base mtg big 1 No. 0.00
body Make_L&T(cat no.WM301BC7D10)
68 Supply,fixing,Testing and commissioning of 1 or 3Ǿ LCD
display type electronic Energy meter of following rating,
multifunction, Din rail type, compatible with RS485 and wifi
module in existing panel/frame/box complete as reqd.

a) 1_Phase Energy meter Meter, Make_L&T (Cat WD4000 2 Nos. 0.00

101OOO) or equivalent..
b) 3_Phase Energy meter Meter,Make_L&T (Cat WD4000 2 Nos. 0.00
103OOO) or equivalent.
69 Fixing Energy meter on exising panel door including Cutting 2 Nos. 0.00
MS pannel door and drilling holes and intact with GI srip,
nut,bolts & washers complete as requird.
70 Supply installation,testing and commissioning of 3-Ph,DOL 1 No. 0.00
Starter for 10 HP Motor, 415/440 volts,with sheet steel
enclosure, type MN with SPP feature including drilling holes
on the board,earthing etc. complete as reqd. make_ L&T (Cat
no SS94351) or equivalent.

Page 8
71 Supply installation,testing and commissioning of 3-Ph,DOL 1 No. 0.00
Starter for 7.5 HP Motor with sheet steel enclosure, type MK
415/440 volts, including drilling holes, earthing etc. Complete
as reqd. make_ L&T (Cat no SS96210) or equivalent.

72 Supply installation,testing and commissioning of 1-Ǿ DOL 1 No. 0.00

Starter for 2.0 HP Motor, 415/440 volts,type_MK with sheet
steel enclosure, including drilling holes, earthing the body
etc. as reqd. Make_L&T (Cat no ST37491BOVO) or equivalent.

73 Supply installation,testing and commissioning of 1-Ph,Starter 1 No. 0.00

(submersible pump) for 2 HP Motor , 220/240 volts, with
sheet steel enclosure, type MRG- 2 , including drilling
holes,earthing etc. as reqd. make_ L&T (Cat no SS96990) or
eqivalent.

OH & POLE
74 S&F of the 80 mm dia GI `B' class 4.5 mtr long with fixing base 5 Nos. 0.00
plate size 300x300x3mm for post top lantern light complete
with reducer socket and GI nipple suitable size as reqd.

75 Supply and fixing GI bracket 2mtrs long of 32 mm dia , class 5 Nos. 0.00
B GI pipe for mounting of fittings i/c making in shape bending
120°with clamps, wiring 1.5 sq.mm wire, painting etc as reqd.

76 Making masonry pillar with bricks, cement and sand ( 1: 4) of 5 Nos. 0.00
size 450mm x 450mm x 700mm height above the ground level
after 100mm C.C (1: 3 : 6 ) foundation and plastered 15 mm
on all sides including painting with white cement etc as reqd.

77 Supplying, fixing, connecting and commissioning of control 5 Nos. 0.00

box of 2mm thick MS sheet of size 200 x200x 125mm deep on
existing pole with 1 no. 6 Amp. to 32 Amp. SPMCB, 10 kA,
brass neutral link & phase link 6 way all these items fixed on 6
mm thick bakelite sheet, i/c painting earthing etc as reqd.

78 Dismantling of pole / street light standard/ strut embeded in 20 Nos. 0.00

brick bllast foundation etc as required.
79 Erection of metallic pole of following length in cement
concrete1:3:6 (1 cement : 3 coarse sand : 6 graded stone
aggregate 40mm nominal size) foundation including
excavation and refilling etc. as required.

a) Above 4.5 meter and upto 6.5 meter 2 Nos. 0.00

b) Above 6.5 meter and upto 8.0 meter 2 Nos. 0.00
c) Above 8.0 meter and upto 10.0 meter 2 Nos. 0.00
d) Above 10.00 meter and upto 12.00 meter 2 Nos. 0.00
80 Painting of following size steel tubular / GI street light poles
with minimum two coats of good quality (approved make)
aluminum paint after cleaning the surface and rubbing the old
paint etc. as required complete.

a) up to 4.5 mtr. Long 50 Nos. 0.00

b) above 4.5 mtr. Upto 8mtrs. Long 30 Nos. 0.00
81 Numbering of poles by enamel paint with black letter on 80 Nos. 0.00
yellow base etc. as required.
CABLES
82 Supply,laying,testing and commissioning 10 pairs telephone
armoured cable (jelly filled) 0.5 mm tinned copper conductor
in following manner as per specifications complete as
required..

a) In ground i/c excavation sand cushioning protective covering, 25.00 Mtr. 0.00
refilling of earth as reqd.
b) Fixing on surface with MS clamp 8.00 Mtr. 0.00
c) In existing pipe 10.00 Mtr. 0.00

Page 9
d) In existing open duct. 10.00 Mtr. 0.00
83 Supply,laying,testing and commissioning 20 pairs telephone
armoured cable (jelly filled) 0.5 mm tinned copper conductor
in following manner as per specifications complete as
required..

a) In ground i/c excavation sand cushioning protective covering, 25.00 Mtr. 0.00
refilling of earth as reqd.
b) Fixing on surface with MS clamp 8.00 Mtr. 0.00
c) In existing pipe 10.00 Mtr. 0.00
d) In existing open duct. 10.00 Mtr. 0.00
84 Supply,laying,testing and commissioning of one no. PVC
insulated & PVC sheathed aluminum conductor steel
armoured cable of following sizes 1.1kV grade Ain following
manners as per specifications reqd.

I) In ground i/c excavation sand cushioning protective covering,

refilling of earth as reqd.
a) 2 x 6 sq.mm. 50.00 Mtr. 0.00
b) 2 x 10 sq.mm. 20.00 Mtr. 0.00
c) 4 x 16 sq.mm. 50.00 Mtr. 0.00
d) 3.5 x 25 sq.mm. 50.00 Mtr. 0.00
e) 3.5 x 35 sq.mm. 20.00 Mtr. 0.00
f) 3.5 x 50 sq.mm. 20.00 Mtr. 0.00
g) 3.5 x 70 sq.mm. 50.00 Mtr. 0.00
h) 3.5 x 95 sq.mm. 20.00 Mtr. 0.00
i) 3.5 x 120 sq.mm. 50.00 Mtr. 0.00
II) On surface
a) 2 x 6 sq.mm. 10.00 Mtr. 0.00
b) 2 x 10 sq.mm. 10.00 Mtr. 0.00
c) 4 x 16 sq.mm. 10.00 Mtr. 0.00
d) 3.5 x 25 sq.mm. 10.00 Mtr. 0.00
e) 3.5 x 35 sq.mm. 10.00 Mtr. 0.00
f) 3.5 x 50 sq.mm. 10.00 Mtr. 0.00
g) 3.5 x 70 sq.mm. 10.00 Mtr. 0.00
h) 3.5 x 95 sq.mm. 10.00 Mtr. 0.00
i) 3.5 x 120 sq.mm. 10.00 Mtr. 0.00
III) On existing pipe
a) 2 x 6 sq.mm. 10.00 Mtr. 0.00
b) 2 x 10 sq.mm. 10.00 Mtr. 0.00
c) 4 x 16 sq.mm. 10.00 Mtr. 0.00
d) 3.5 x 25 sq.mm. 10.00 Mtr. 0.00
e) 3.5 x 35 sq.mm. 10.00 Mtr. 0.00
f) 3.5 x 50 sq.mm. 10.00 Mtr. 0.00
g) 3.5 x 70 sq.mm. 10.00 Mtr. 0.00
h) 3.5 x 95 sq.mm. 10.00 Mtr. 0.00
i) 3.5 x 120 sq.mm. 10.00 Mtr. 0.00
IV) On existing open duct.
a) 2 x 6 sq.mm. 50.00 Mtr. 0.00
b) 2 x 10 sq.mm. 50.00 Mtr. 0.00
c) 4 x 16 sq.mm. 10.00 Mtr. 0.00
d) 3.5 x 25 sq.mm. 10.00 Mtr. 0.00
e) 3.5 x 35 sq.mm. 10.00 Mtr. 0.00
f) 3.5 x 50 sq.mm. 10.00 Mtr. 0.00
g) 3.5 x 70 sq.mm. 10.00 Mtr. 0.00
h) 3.5 x 95 sq.mm. 10.00 Mtr. 0.00
i) 3.5 x 120 sq.mm. 10.00 Mtr. 0.00
85 Supplying and making end termination with brass compression
gland, aluminum lugs for following size of PVC insulated & PVC
sheathed / XLPE aluminum cable of 1.1kV grade as reqd.

a) 2x6 sq.mm./3x6 sq.mm. 40 Nos. 0.00

Page 10
b) 2x10 sq.mm./ 3x10 sq.mm. 40 Nos. 0.00
c) 2x16 sq.mm. 8 Nos. 0.00
d) 4x16 sq.mm. 8 Nos. 0.00
e) 3-1/2x25/ 4 x 25 sq.mm. 8 Nos. 0.00
f) 3-1/2x35/ 4 x 35 sq.mm. 8 Nos. 0.00
g) 3-1/2x 50/4 x 50 sq.mm. 8 Nos. 0.00
h) 3-1/2x 70 / 4 x 70 sq.mm. 8 Nos. 0.00
i) 3-1/2x 95 /4 x 95 sq.mm. 8 Nos. 0.00
j) 3-1/2x 120 /4 x 120 sq.mm. 4 Nos. 0.00
k) 3-1/2x 185 / 4 x 185 sq.mm. 4 Nos. 0.00
86 Supply and making straight through joint with cast resin
compound including ferrules and other jointing materials for
following size of PVC insulated and PVC sheathed / XLPE
aluminium conductor cable of 1.1 KV grade as required.

a) 2x16/2x10 sq.mm./ 3x6/ 3x10sq.mm. 5 Nos. 0.00

b) 4x16 sq.mm. 5 Nos. 0.00
c) 3-1/2x25/ 4 x 25 sq.mm. 5 Nos. 0.00
d) 3-1/2x35 / 4 x 35 sq.mm. 2 Nos. 0.00
e) 3-1/2x 50/ 4 x50 sq.mm. 2 Nos. 0.00
f) 3-1/2x 70/4x 70 sq.mm. 2 Nos. 0.00
g) 3-1/2x 95/ 4 x 95 sq.mm. 2 Nos. 0.00
h) 3-1/2x 120 / 4 x 120 sq.mm. 2 Nos. 0.00
i) 3-1/2x 185/4 x 185 sq.mm. 2 Nos. 0.00
87 Earthing with G.I earth pipe 4.5 metre long 40 mm dia 2 Sets 0.00
including accessories, and providing masonry enclosure with
cover plate having locking arrangement and watering pipe etc.
with charcoal/ coke and salt as required.

88 Earthing with GI earth plate size 600mm x 600mm x 6mm with 2 Sets 0.00
watering 20mm dia. 2.7 mtr long GI pipe, hinged C.I. 5 mm
cover plate/ RCC 100 mm and funnel as per specification,
with charcoal & salt for electrode as reqd.

89 Providing & fixing copper earth strip of size 25mm x 5mm in 25.00 Mtr. 0.00
40 mm GI pipe with bend etc in ground / surface as per
specification.
90 Providing & fixing GI earth strip of size 25mm x 5mm in 40 mm 100.00 Mtr. 0.00
GI pipe with bend etc in ground / surface as per specification.

91 P&F 25 mm x 5 mm copper strip on surface or in recessed for 25.00 Mtr. 0.00

loop connection etc as reqd.
92 P&F 25 mm x 5 mm G.I. strip on surface or in recessed for loop 100.00 Mtr. 0.00
connection etc as reqd.
93 Supply installation,testing and commissioning of of lightning 2 Nos. 0.00
conductor finial, made of 25 mm dia 300mm long, G.I. tube,
having single prong at top, with 85mm dia 6mm thick G.I. base
plate and rag bolts including holes etc.complete as required.

94 Supply installation,testing and commissioning of G.I. tape 20 100.00 Mtr. 0.00

mm x 3 mm thick on parapet or surface of wallfor lightning
conductor complete as required.(for horizontal run).

95 Supply installation,testing and commissioning of G.I. tape 20 50.00 Mtr. 0.00

mm x 3 mm thick on parapet or surface of wall for lightning
conductor complete as required.(for Vertical run)

96 Fixing of copper / G.I. tape 20 mm x 3mm thick on parapet or 50.00 Mtr. 0.00
surface of wall for lithtning conductor complete as required
(For horizontal run).
97 P & F 6 SWG dia. GI wire on surface or in recess for loop 200.00 Mtr. 0.00
earthing as reqd.
98 Providing & fixing of size 32 mm x 12.5 mm. DLP mini trunking 200.00 Mtrs 0.00
system with independent cover as reqd.

Page 11
99 Providing & fixing accessories for following size of DLP mini
trunking system as reqd. (32 mm x 12.5 mm. )
a) Flat junction 5 Nos. 0.00
b) Changeable flat angle 5 Nos. 0.00
c) Changeable internal /External angle 5 Nos. 0.00
d) End cap left or right 10 Nos. 0.00
100 Providing & fixing of size 32 mm x 20 mm. DLP mini trunking 200.00 Mtrs 0.00
system with independent cover as reqd.
101 Providing & fixing accessories for following size of DLP mini
trunking system as reqd. (32 mm x 20 mm. )
a) Flat junction 5.00 Nos. 0.00
b) Changeable flat angle 5.00 Nos. 0.00
c) Changeable internal /External angle 5.00 Nos. 0.00
d) End cap left or right 10.00 Nos. 0.00
102 Providing & fixing of following size of DLP trunking on surface 100.00 Mtrs. 0.00
with suitable plug & screws as reqd. (105 mm x 50 mm. )

103 Providing & fixing of accessories for folliwing size of DLP

trunking system as reqd. (105 mm x 50 mm. )
a) Flexible cover for 85 mm width 100.00 Mtr 0.00
b) End Caps 10 Nos. 0.00
c) Base Joint 10 Nos. 0.00
d) Joint for 85 mm width cover 10 Nos. 0.00
e) Clips 10 Nos. 0.00
f) VDI accessories for external angle 2 Nos. 0.00
g) VDI accessories for internal angle 2 Nos. 0.00
h) Flat junction 2 Nos. 0.00
i) VDI accessories for flat junction 2 Nos. 0.00
j) Flat angle 2 Nos. 0.00
k) Internal angle adjustable from 80 - 100 2 Nos. 0.00
l) External angle adjustable from 60 - 120 2 Nos. 0.00
m) Capacity change 2 Nos. 0.00
104 S&L one no. HDPE pipe size inner dia. 50 mm andsuitable for 6
kg pressure as per specification.
a) In ground i/c excavation sand cushioning protective covering, 50.00 Mtr. 0.00
refilling of earth as reqd.
b) Fixing on surface with MS clamp 8.00 Mtr. 0.00
c) In existing pipe 10.00 Mtr. 0.00
d) In existing open duct. 10.00 Mtr. 0.00
105 Drawing of RG-6 cable / network cable/ wiring cable/ 1000.00 Mtrs 0.00
telephone cable in existing surface /concealed conduits reqd.

106 Providing, laying and fixing following dia G.I. pipe class B with
G. I. Fittings complete as required
a) 50 mm dia 10.00 Mtrs 0.00
b) 80 mm dia 10.00 Mtrs 0.00
c) 100 mm dia 10.00 Mtrs 0.00
107 Providing, laying and fixing following dia RCC pipe NP2 class
(light duty) in ground complete with RCC collars, jointing with
cement mortar 1:2 (1 cement : 2 fine sand ) including
trenching (75 cm deep) and refilling etc as required.

a) 150 mm dia 5.00 Mtrs 0.00

b) 250 mm dia 5.00 Mtrs 0.00
c) 300 mm dia 5.00 Mtrs 0.00
CIVIL WORKS
108 Making hole on wall for fixing exhaust fan upto 18 " size and 2 Nos. 0.00
making good the same.

Page 12
109 Supply installation,testing and commissioning of M.S. fan 5 Nos. 0.00
clamp type I or II of 16 mm dia M.S. bar, bent to shape with
hooked ends in R.C.C. slabs or beams during laying, including
painting the exposed portion of loop, all as per standard
design complete.

110 Supply installation,testing and commissioning of circular/ 10 Each 0.00

Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of
internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick
M.S.sheet with its top surface hacked for proper bonding, top
lid shall be screwed into the cast iron/ M.S. sheet box by
means of 3.3 mm dia round headed screws,one lock at the
corners. Clamp shall be made of 12 mm dia M.S. bar bent to
shape as per standard drawing.

111 Structural steel work riveted, bolted or welded in built up 50.00 Kgs 0.00
sections, trusses and framed work, including cutting, hoisting,
fixing in position and applying a priming coat of approved
steel primer all complete.

112 Providing and laying in position reinforced cement concrete 1.00 Cum 0.00
1:2:4(1 cement :2coarse sand:4graded stone aggregate 20mm
nominal size) in foundation of pump, DG set etc including form
work etc as required .

113 Providing brick work (in width 225 mm or more ) with F.P.S. 1.00 Cum 0.00
bricks of class designation 7.5 in cement mortal 1:4 (1
cement :4 coarse sand ) at all levels.
114 Providing cement plaster of mix 1:4 (1 cement : 4 fine sand ) at 10.00 Sqm 0.00
all levels
115 Excavation for foundation in soft soil i/c dressing of sides and 10.00 Cub 0.00
ramming of bottoms lift up1.5mtrs i/c getting out the mtrs.
excavated soiland disposal of surplus excavated soil as directed
within a lead of 50 mtrs.

116 Filling available excavated earth in trenches sides of 10.00 Cub 0.00
foundations etc. in layers not exceeding 20 cm indepth mtrs.
conolidating each deposited layer by ramming and watering
lead upto 50mtrs.

FAN REPAIR
117 Rewinding of ceiling fans of following sizes i/c dismantling of
rotor,cutting & removing damage winding and rewinding thr
rotor with material including winding wire,insulation varnish
paper,connecting copper leads including testing and
commissioning etc including dismantling and re-fixing
compelte as required.(old copper shall be retained by
contractor)

a) 48" 50 Nos. 0.00

b) 56" 10 Nos. 0.00
118 Rewinding of exhaust fans of following sizes i/c dismantling of
rotor,cutting & removing damage winding and rewinding thr
rotor with material including winding wire,insulation varnish
paper,connecting copper leads including testing and
commissioning compelte including dismantling and re-fixing
as required.(old copper shall be retained by contractor)

a) 12" 2 Nos. 0.00

b) 15 to 18" 2 Nos. 0.00
119 Rewinding of Air curtain motor i/c dismantling cutting the 2 Nos. 0.00
damaged winding and providing rewinding along with
insulation paper, varnish, connecting copper leads of suitable
quality including testing as required .(Old burnt wire shall be
retain by the contractor).

Page 13
120 Overhauling ceiling fan of any size including opening and 40 Nos. 0.00
refitting of fan after checking ,cleaning all parts, bearing/
bush, greasing/ oiling including Supply & replacement of
defective rubber real, rings,nut,bolts ,washer, hanger clamps,
bearing plates,cutter/split pin etc complete as required.

121 Overhauling exhaust fan of any size including opening and 20 Nos. 0.00
refitting of fan after checking ,cleaning all parts, bearing/
bush, greasing/ oiling including Supply & replacement of
defective rubber real, rings,nut,bolts ,washer ,hanger
clamps ,bearing plates,cutter/split pin etc complete as
required.
122 Overhauling of air-curtain of any size including dismantling 3 Nos. 0.00
and re-fixing complete unit with rag bolts, checking, clening,
oiling greasing, replacement of defective spares etc. (Extra
cost will be paid against used new parts after submitted bill).
reassembling the air curtain testing and commissioning as
reqd..

123 Cleaning of ceiling fan with detergent at site and replacement 100 Nos. 0.00
of damaged items i.e. rubber real, cutter pin, capacitor clamp,
nut and bolts of hanger clamps etc as required.

124 Cleaning of exhaust fan installed in kitchen/mess area up to 20 Nos. 0.00

18"size including dismantling bearings,checking, cleaning,
greasing, replacing rubber rings,nut bolts,hander
clamps,bearing plates,cutter pin etc. if required reassembling,
testing & commissioning complete as required.

125 Cleaning of air curtain of any size installed in kitchen/mess 10 Nos. 0.00
area including opening cabinet, bearings,checking, cleaning,
greasing, replacing rubber rings,nut bolts,hander
clamps,bearing plates,cutter pin etc. if required reassembling,
testing & commissioning complete as required.

126 Supply & Fxing of following size bearing complete as required.

a) 6201 ZZ 20 Nos. 0.00

b) 6202 ZZ 20 Nos. 0.00
c) 6203 2Z 10 Nos. 0.00
d) 6204 2Z 10 Nos. 0.00
127 Supplying and fixing of following capacity capacitor suitable
for ceiling fan.
a) 2.5 MFD Capacitor 50 Nos. 0.00
128 Dismantling and re-fixing of any size ceiling fan (at normal 40 Nos. 0.00
height) complete including connection as requied.
129 Dismantling and re-fixing of exhaust fan of size 12"to 24" with 20 Nos. 0.00
required nut, bolts,washer, fasteners and rag bolts etc. as
reqd.
130 Dismantling and re-fixing of air-curtain of any size complete 3 Nos. 0.00
including electrical connection as requied.
131 Repairing of housing for bearing side /bush side /in fan body 20 Nos. 0.00
in ceiling fan /exhaust fan /rally fan/ cabin fan/ pedestal fan/
water lifting pump/ air-circulator.
132 Carriage of ceiling fan and regulator / exhaust fan from store 60 Nos. 0.00
to site as required.
133 Painting of ceiling fan/exhaust any size with one or more 20 Nos. 0.00
coats with supper enamel paint of approved brand i/c cleaning
and making smooth surface with emery paper and detergent
etc. as required.

Page 14
134 Supplying and fixing fan blade set comprising 3 blades with 10 Nos. 0.00
1200 mm sweep ceiling fan i/c dismantling of existing creaked
fan blades.
Total Rs. 0.00

Page 15