MYPIN ① Measured value (PV)/Various parameter symbols Parameters setting
↓ SET
Resistance Controller ② Parameter value/Rate value/ct/AL1 1、Alarm setting: In the displaying estate, press and hold Low display setting.
③④⑤ Indication lamps for Alarm 1/2/3 SET key for more than 3 seconds, enter alarm mode parameters range:-1999～9999
User Manual
setting menu. Press ＜＜/RST key, LED flashes, press / key
Thanks a lot for selecting products!
On: Output Off: No alarm
to modify,and then press SET key to confirm. Press SET key to
↓SET
Before operating this instrument, please carefully read this ⑥ Select/Confirm key Input High display setting.
read the following parameters one by one.
manual and fully understand its contents. If have problems, range:-1999～9999
⑦ Shift/Clear /Reset key 2、The instrument will return to the measuring estate without
please contact our sales or distributors whom you buy from.
⑧ Up key ⑨ Down key any operation for 25 seconds. ↓ SET Decimal point setting: 0-3 stands
This manual is subject to change without prior notice.
Indication lamps for Resistance for 0000, 000.0, 00.00 and
Operation process
Warning 10 Ω 0.000 seperately
11 K Ω 12 M Ω ↓ SET
Please do not turn on the power supply until all of the wiring PowerON
is completed. Otherwise electrical shock, fire or malfunction ↓ Analogue Low value setting
Models range:LSP ≤ trL ≤ USP
may result. All LED on
Do not wire when the power is on. Do not connect the unused DR □ - □□□□□□ Input signal: any betwwen 0-500M Ω ① ↓ SET
terminals. Do not turn on the power supply when cleaning this
Communication：N：No
↓ Analogue High value setting
instrument. Do not disassemble, repair or modify the instrument. range:LSP ≤ trH ≤ USP
2：R232 4： R485 Input signal type
This may cause electrical shock, fire or malfunction
AL3: R:Relay S:SSR/LOGIC N：no ↓
Use this instrument in the scope of its specifications. Other-
AL2：R:Relay S:SSR/LOGIC N:no
↓ Parameter lock password.
wise fire or malfunction may result. Up linit LCK=000 means the parameter can
AL1：R:Relay S:SSR/LOGIC N:no
The use life of the output relay is quite different according Down limit
Analogue output：blank:no be modified.
to it capacity and conditions. If use out of its scope, fire or
I：DC 0-10mA or DC 4-20mA ↓ ↓ LCK=010 means it can be read only.
malfunction may result. Return to AL1
Power supply：black：AC 90-260V PV display
① AL3 and current output,only one can be selected at
！ Caution 50/60Hz E: 18-30V AC/DC Rate setting
the same time.
DR series Resistance Controller
This instrument should be installed in a domestic environment.
Dimensions：48H × 96W × 80L
Alarm parameter setting ★ The value showed is the factory setting value. If
Otherwise electrical shock, fire or malfunction may result.
★ Input signal is selected by user
↓ the user want to modify one of the them, the relative
The operating temperature environment should between 0 (32F) Measuring display parameter also should be modified, otherwise it will
to 50 (122F). Specifications Rate setting cause faulty measurement.
To avoid using this instrument in environment full of dust or ↓ SET＞3S
＞＞
P re s s / k e y f o r m o r e t h a n 3 s e c o nd s. c a n
＞＞
Power supply 90-260V AC 50/60Hz
caustic gas. Alarm 1 HIGH limit setting， enter/quit from the second grade parameters
To avoid using this instrument in environment of strong shock Consumption ≤ 5VA
range:LSP≤AL1≤USP s e t t in g ( o n l y c o m m u n i ca t i o n a c t i v e )
Accuracy 0.3%F.S ± 2digit
or concussion. ↓ SET
To avoid using this instrument in environment of overflow Sampling rate
Alarm
≤ 8 times/second
Relay: NO AC 250V/3A or DC 30V/3A cos =1
Alarm 1 mode setting ↓SET
water or explosive oil. H: High SET Bit rate setting. The factory
↓
The instrument has the recovable protection parts.It can pre- Input refer the input signal selection
vent demages in case of short circuit. Analogue 0-10V or 4-20mA, free set for control ↓ SET setting is 9.6k bit/s.
output range by software AL1 hysteresis value,range:±50. ↓ SET
Applications Auxiliary Power DC 12/24V/30mA 00，the factory setting is 0.5 Communication address se-
The instrument has data-holding or peak value remain function. Communication RS232 or RS485 for option ↓ SET lection Range:000-255
It can be use with 2-wire or 4-wire weight sensor.Isolated
sensor power and RS 485 communication is available. For non- Dmensions
Alarm 2 LOW limit setting，
↓SET
range:LSP≤AL2≤USP Linear input process
linear input,the instrument can process for 20 stages linear 96 ↓ SET
processing.The input, output and the power supply is isolated ← → ←
80
→ Alarm 2 mode setting NO=not select Yes=select
↑ L:Low ↓SET Password
Name of parts 48 ↑4 4 ↓ SET of calibration param-
eters for the factory or dis-
↓ ↓ AL2 hysteresis value,range:±50.
tributor only
←1 0
↑↑↑ ↑
③ AL1 Ω +0.5 00，the factory setting is 0.5
91 30
④ AL2 KΩ ←11 ←
0
→←→ ↓SET Diagram connections
⑤ AL3 MΩ ←1 2 ↑ Offset value display,
AL1
45+0.5
AL2
COM
0 Offset value=PV-PVF,range:±50.0
SET
<<
⑥ <</Rst
↓ 12 11 10 9 8 7 6 5 4 3 2 1
<<
↓ SET
A
→
→
→
→
↑ ↑ ↑ ↑ ↑
30 Input signal selection.
B
RXD TXD 18-30VAC/DC or
② ⑦ ⑧ ⑨ ↓ 90-260V AC
96W × 48H × 80L
