VEG800 SERIAL BOARD FOR FLOOR COMMANDS LCD 600-601 SERIAL ICARO DISPLAY FOR FLOOR COMMANDS
OUT OF SERVICE
KG
Programming
jumper Call buttons
Serial
Board
PARAMETERS RELATED TO THE TYPE OF SIGNAL CARRIED OUT BY THE OUTPUTS AND TO FLOOR NUMBERING ON SERIAL BOARD AND
DISPLAY (TO BE MODIFIED ON THE EURO BOARD IN THE CONTROL PANEL)
PELAZZA PEPPINO s.r.l.
Quadri di Manovra per Ascensori e Montacarichi
Lifts Control Panels
20063 CERNUSCO SUL NAVIGLIO (MI) ITALY
Via Ponchielli, 6/8
Tel. 02/9231694 – 02/9242706 – Fax 02/9242706
www.pelazza.com
E-mail: pelazza@pelazza.com
PROGRAM: EURO-INV13N CLIENT: MILAN ASCENSORE Ref: MARCH 2015 MRL 5.5 KW -
12PE-PA-S 2 ACC. - OP.380V3PH
Lift: VVVF – Simplex 1PE – Automatic Doors – Closed Doors Parking – Serial
PARAMETERS TO BE MODIFIED IF THE EURO BOARD SHOULD BE REINITIALIZED
PAR. VALUE MEANING
1 6 (def.) TMA = Maximum opening doors time (to be regulated about 1-2 sec over
the time required to open the doors)
2 6 (def.) TAP = Restarting and open doors parking time
3 8 TCH = Maximum time for doors closing
5 6 TMP = Engagement manoeuvre time and A67 fault signal time (5xP5 sec)
6 30 TMC = Maximum travel time
9 4 TOC = Engage time from closing doors start for parking (to be regulated
about 1-2 sec over the time required to close the doors)
10 69 P output used for low speed command
11 20 TRIF = Contactrors drop delay at stop: 7 (Inverter without encoder 27x0,1=0,7 sec)
20 (Fuji 20x0,1= 2,0 sec)
12 99 (def.) TSN = Return to parking floor time (from 0 to 99 x 10 sec)
13 99 (def.) 99 = Holding Connection to Battery During power failure
1 = Disconnection from Battery after 1 minute of power failure
14 99 (def.) RU output used for main contactors control (via FS3/CPF)
15 93 TMR3 = Emergency cycle end time (93x0,1=9,3 sec)
17 3 RITING = Direction reversion delay (3x0.1=1.5sec.)
19 36 68 = Maximum number of calls to parallel inputs = 24
36 = Maximum number of calls to parallel inputs = 12
20 = Maximum number of calls to parallel inputs = 8
20 1 Cabin calls on to parallel inputs
21 0 (def.) 0 = A3 Emendament disabled
1 = Brakes control for A3 Emendament type ELEC/1 or ELEC/1R
7 = Speed regulator control for A3 Emendament type ELEC/L
22 3 3 = Electric lift type with automatic or semiautomatic doors
2 = Electric lift type with manual doors
23 3 1 = Opened doors parking + Powered operator during travel
3 = Closed doors parking + Powered operator during travel (for manual doors = 3)
24 0 Down Re-phasing + 2 speed lift type
25 2 Automatic re-phasing
26 6 Inspection in high+low speed (reduced by VVVF) with stop on the re-phase impulsors
27 0 (def.) 0 = Fixed Confirmation Control and Directions signalling
28 2 2 = Normal selector + Re-levelling disabled
3 = Reverse selector + Re-levelling disabled
0 = Normal selector + Re-levelling enabled with safety circuit control on AUX3 input
1 = Reverse selector + Re-levelling enabled with safety circuit control on AUX3 input
29 0 Running direction control disabled
30 2 2 = 30KG floor contact (CCO) disabled + full load contact (CCC) enabled
0 = 30KG floor contact (CCO) enabled + full load contact (CCC) enabled
32 0 Door control enable
34 32 Registered lift type
35 19 19 = Cabin and floors full serial activation
17 = Cabin serial activation, floor serial display
1 = Only floor serial activation and cabin serial display
36 2 Floors number
38 10 (def.) Lower floor numbering on serial display
(1=-9, 2=-8,...,9=-1, 10=0, 11=1, …, 20=10)
43 31 (def.) Impulsors and CCC Full load exclusion from serial
50 3 2° Selective access enabled at 1° stop
51 3 2° Selective access enabled at 2° stop
83 32 (def.) 32 = Return to parking floor disabled
N = Stop number of the return to parking floor (from 0 to 31)
84 33 32 = Emergency descending disabled
33 = Emergency descending with stop at the nearest floor
94 17 16 = Safety circuit control on CS1 input disabled
17 = Safety circuit control on CS1 input disabled + Second access enabled
95 36 Gong at stop and standard UP/DOWN registration
96 0 0 = Reversed binary display outputs (DEC 16)
4 = Normal binary display outputs
8 = 7 segments display outputs instead of normal position outputs
FUJI FRENIC LIFT 5,5 kW – PARAMETERS PROGRAMMING (Gearless)
Milan Ascensore Rif.Ord. March 2015 MRL 5,5KW 1/2Acc. OP.380V3PH V= 1m/s
P01 Motor Poles 20
P02 Motor power 4,30 kW
P03 Motor current 8,8 A
P06 No load motor current 4,4 A
C21 Speed measureament unit 0 (r/min)
F03 Motor speed regulation (reference for acc/dec time) 119 r/min
F04 Motor rated speed (reference for motor supply voltage) 119 r/min
F05 Motor rated voltage 360 Vac
F11 Motor thermal protection current 8,8 A
F24 Start frequency hold time 0,8 s
F25 Brake release frequency 0,30 r/min
F42 Control mode selection (with/without encoder) 1 (encoder)
C06 Inspection speed 23,8 r/min
C07 Low speed 12 r/min
C11 Nominal high speed 119 r/min
H74 Speed agreement hysteresis 0,4 r/min
L01 Encoder type 4 (Endat)
L02 Encoder resolution 2048
L36 Speed loop controller P gain at high speed 2,50
L38 Speed loop controller P gain at low speed 1,50
L40 Switching speed for P gain at low speed 14,4 r/min
L41 Switching speed for P gain at high speed 24 r/min
L65 Unbalanced load compensation activation 1
L66 Unbalanced load compensation activation time 0,8 s
L68 Unbalanced load compensation speed proportional gain 2,5
L69 Unbalanced load compensation integral time 0,003
F07 Acceleration time 1,80 s
E13 Deceleration time 1,80 s
E30 Emergency return to floor maximim speed 12 r/min
E31 Running lift detection speed 2,7 r/min
E32 Running lift detection speed hysteresis 0,3 r/min
PELAZZA PEPPINO Srl
Milan order March 2015 MRL-5,5KW-2 ACC.-OP.380V3PH
Complete pre-wired kit for n.2 stops -PF0009059
Item Code Description Unit Qty
CABIN FLEX CABLES
DONPRECAPXXX020 BLACK H05VVH6-F 24G0.75 flat flex cable mt. 36,00
DONPRECAPXXX023 BLACK H05VVH6-F 12G0.75 flat flex cable mt. 18,00
XXXPRECAPSEM001 Connectors Kit for 24 (12+12) F1A/F1B Flex PZ 1,00
XXXPRECAPSEM002 Connectors Kit for 24 (12+12) F2A/F2B Flex PZ 1,00
XXXPRECAPSEM020 Connectors Kit for 12 (7+5) F2A/F2B Flex PZ 1,00
PRE-WIRING CABIN WITH PUSH-BUTTON
XXXPRESEVSEM007 CU-CT Impulsors Conn.3P (IM1) PZ 1,00
XXXPRESEVSEM008 ID-IS Impulsors Conn.3P (IM2) PZ 1,00
XXXPREOPESEM001 Operator Cable (OP) PZ 2,00
XXXPREBMTSEM011 Service Push-button with 220v Plug (MAN/PC) PZ 1,00
XXXPRECTCSEM002 Frame Cable (AR) PZ 1,00
XXXPRECTCSEM046 Cabin Roof Manhole Cable (BT) PZ 1,00
XXXPRECTCSEM067 Cabin Stop Bracket Cable (FC) PZ 1,00
XXXPRECTCSEM003 Mobile Cabin Light Cable (LM) PZ 1,00
XXXPRECTCSEM004 Permanent Cabin Light Cable (LF) PZ 1,00
XXXPRECTCSEM015 Supply Operator Cable (OR) PZ 1,00
XXXPREBOTSEM081 Required only for lift with OP.230Vdc PZ 1,00
XXXPREBOTSEM082 (Supplied inside the Panel) PZ 1,00
XXXPRECTCSEM012 Cabin Final Limit (EX) PZ 1,00
XXXPREFOTSEM002 FTA-FTB double Photocell (FOT) PZ 1,00
XXXPREPSCSEM001 Overload Cable (SVR) PZ 1,00
XXXPREBTCSEM086 Serial Cabin Push-Button Cables F3-1T16 (BC1/BC2) PZ 1,00
XXXPRECTCSEM190 Cabin Roof Junction Box SCH Electric PA Serial 2Acc MRL PZ 1,00
DONPREXXXXXX012 90MM Wall Pipeline PZ 3,00
LABKVAACCXXX001 Normal Impulsors Guide PZ 2,00
MPIKVASEMMAG003 150 x 15 x 6 mm Long Ferrite Plate PZ 6,00
MPIKVASEMMAG002 80 x 20 x 6 mm Ferrite Plate PZ 2,00
SHAFT PRE-WIRING WITH PUSH-BUTTONS
XXXPREVANSEM028 Pizzato Pit Stop (SF) PZ 1,00
XXXPREVANSEM002 Alarm Siren (SA) PZ 1,00
XXXPRECVASEM001 Locks Cable (CP) PZ 2,00
XXXPRECVASEM005 6m Locks Cable (CP) PZ 2,00
XXXPRECVASEM014 Overspeed Governor Tensioner Cable (TD) PZ 1,00
XXXPRECVASEM057 Car Ropes Tensioner Cable (AF) PZ 1,00
XXXPRECVASEM012 Floor Push-Button Serial Cable (VS) PZ 1,00
XXXPRECVASEM046 8m Overspeed Governor Cable (LLR) PZ 1,00
XXXPRECVASEM060 Overspeed Governor Test/Reset Coils Cable (BPR) PZ 1,00
VEGSMPACCCAV016 4x0.5-10m 2C FEMM. Cable (between floors from VEG to VEG) PZ 3,00
EMACEMCABCAV014 N07 V-K 6 sqmm Y/G Wire mt. 5,00
BOCCMOCANXXX014 80 x 60 (24) Closed Pipeline mt. 4,00
BOCCMOCANXXX008 40 x 40 (40) Closed Pipeline mt. 20,00
UPRIGHT SHAFT CABLE (V1)
MORCONPOLFEM008 Screw Female Connector p 5.08 front – 7 pole PZ 1,00
MORCONPOLFEM004 Screw Female Connector p 5.08 front – 3 pole PZ 1,00
ABBMORVITXXX017 2Ways Female Terminal PZ 9,00
ABBMORVITXXX016 3Ways Female Terminal PZ 1,00
EMACEMCABCAV046 H05 V-K 0,75 sqmm colored Wire mt. 128,20
EMACEMCABCAV010 N07 V-K 2,5 sqmm Y/G Wire mt. 15,00
SERIAL PUSH-BUTTONS ACCESSORIES
VEGSMPACCCAV006 50cm 4p AMP Flat Cable(from PULS to SERCAR) PZ 2,00
VEGSMPACCCAV007 72cm 4p AMP Flat Cable (from PULS to SERCAR) PZ 3,00
VEGSMPACCCAV003 15cm 4p AMP Flat Cable (from PULS to VEG) PZ 4,00
VEGSMPEXPXXX004 VEG 800 Board for Floor Buttons Collection PZ 3,00
Milan Ascensore 0101 EASY MOD Push-Buttons Kit
XXXPREBOTSEM097 2F/2A (0,1,0,1) EASY MOD CABIN PUSH-BUTTON PZ 1,00
XXXPREBOTSEM106 EASY MOD FLOOR DOUBLE ARROW PUSH-BUTTON WITH DISPLAY PZ 1,00
XXXPREBOTSEM107 EASY MOD FLOOR DOUBLE ARROW PUSH-BUTTON PZ 3,00
F1A F1B
F1B F1A
PELAZZA PEPPINO s.r.l
F2A F2B
F2B F2A
PELAZZA PEPPINO s.r.l
F3A F3B
F3A
F3B
PELAZZA PEPPINO s.r.l
IM1
PELAZZA PEPPINO s.r.l
IM2
PELAZZA PEPPINO s.r.l
OP
PELAZZA PEPPINO s.r.l
OP
PELAZZA PEPPINO s.r.l
MAN
PC
PELAZZA PEPPINO s.r.l
AR
PELAZZA PEPPINO s.r.l
BT
PELAZZA PEPPINO s.r.l
FC
PELAZZA PEPPINO s.r.l
LM
PELAZZA PEPPINO s.r.l
LF
PELAZZA PEPPINO s.r.l
OR
PELAZZA PEPPINO s.r.l
EX
PELAZZA PEPPINO s.r.l
FOT
PELAZZA PEPPINO s.r.l
SVR
PELAZZA PEPPINO s.r.l
BC1
BC2
VEGA
SERCAR_LCD_2.4
PELAZZA PEPPINO s.r.l
SF
PELAZZA PEPPINO s.r.l
SA
PELAZZA PEPPINO s.r.l
CP
PELAZZA PEPPINO s.r.l
TD
PELAZZA PEPPINO s.r.l
AF
PELAZZA PEPPINO s.r.l
VS
PELAZZA PEPPINO s.r.l
LLR
PELAZZA PEPPINO s.r.l
BPR
PELAZZA PEPPINO s.r.l
PELAZZA PEPPINO s.r.l
PELAZZA PEPPINO s.r.l
STOP '1A' STOP '1' STOP '0A' STOP '0'
CP LLR TD CP CP SA CP
V1
V2
BPR SF AF
PELAZZA PEPPINO s.r.l
