Modify Configuration of Cell Reselection (MOD CELLRESEL)

Function

Use this command to modify the parameters about cell reselection.

Note

None.

Parameters

ID Name Description

Meaning: Indicates the local ID of the cell. It uniquely identifies

LocalCellId Local cell ID
a cell within a BS.
GUI Value Range: 0~255
Unit: None
Actual Value Range: 0~255
MML Default Value: None
Recommended Value: None
Parameter Relationship: None
Service Interrupted After Modification: N/A
Impact on Radio Network Performance: None
Applicable Mode: L

Qhyst Hysteresis Meaning: Indicates the hysteresis for cell reselection when
value for RSRP values are used in the evaluation. This parameter must
ranking be set based on the slow fading characteristic of the area
criteria covered by the cell. The greater the slow fading variance is,
the larger the value of this parameter must be set to. A larger
value of the hysteresis results in a larger boundary of the
serving cell and a lower probability of cell reselection to
neighboring cells.
GUI Value Range: DB0_Q_HYST(0dB), DB1_Q_HYST(1dB),
DB2_Q_HYST(2dB), DB3_Q_HYST(3dB),
DB4_Q_HYST(4dB), DB5_Q_HYST(5dB),
DB6_Q_HYST(6dB), DB8_Q_HYST(8dB),
DB10_Q_HYST(10dB), DB12_Q_HYST(12dB),
DB14_Q_HYST(14dB), DB16_Q_HYST(16dB),
DB18_Q_HYST(18dB), DB20_Q_HYST(20dB),
DB22_Q_HYST(22dB), DB24_Q_HYST(24dB)
Unit: dB
Actual Value Range: DB0_Q_HYST, DB1_Q_HYST,
DB2_Q_HYST, DB3_Q_HYST, DB4_Q_HYST,
DB5_Q_HYST, DB6_Q_HYST, DB8_Q_HYST,
DB10_Q_HYST, DB12_Q_HYST, DB14_Q_HYST,
DB16_Q_HYST, DB18_Q_HYST, DB20_Q_HYST,
DB22_Q_HYST, DB24_Q_HYST
MML Default Value: None
Recommended Value: DB4_Q_HYST(4dB)
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
 mode.)
Impact on Radio Network Performance: With other parameters
related to cell reselection unchanged, a larger value of this
parameter leads to a lower probability of reselection to an
intra-frequency or same-priority neighboring cell. A smaller
value of this parameter leads to a higher probability, but a
larger number of ping-pong cell reselections.
Applicable Mode: L

SpeedDepReselCfgI Speed- Meaning: Indicates whether to set the parameters related to

nd dependent speed-dependent cell reselection.
reselection GUI Value Range: NOT_CFG(Not configure), CFG(Configure)
parameter
configure Unit: None
indicator Actual Value Range: NOT_CFG, CFG
MML Default Value: None
Recommended Value: NOT_CFG(Not configure)
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

TEvaluation The duration Meaning: Indicates the duration in which the mobility status of
for evaluating the UE is evaluated. This parameter is one of the key
criteria to parameters in deciding on the UE mobility. A smaller value of
enter mobility this parameter may lead to more frequent switching among
states mobility status and lower decision accuracy. A larger value of
this parameter leads to the opposite effect.
GUI Value Range: S30_T_EVALULATION(30s),
S60_T_EVALULATION(60s), S120_T_EVALULATION(120s),
S180_T_EVALULATION(180s),
S240_T_EVALULATION(240s)
Unit: s
Actual Value Range: S30_T_EVALULATION,
S60_T_EVALULATION, S120_T_EVALULATION,
S180_T_EVALULATION, S240_T_EVALULATION
MML Default Value: None
Recommended Value: S60_T_EVALULATION(60s)
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of the
SpeedDepReselCfgInd parameter.
If the SpeedDepReselCfgInd parameter is set to CFG, this
parameter must be set.
If the SpeedDepReselCfgInd parameter is set to NOT_CFG,
this parameter does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A smaller value of this
parameter leads to a lower probability of the UE entering the
high mobility or medium mobility state and a smaller impact of
the mobility status on cell reselections. A larger value of this
 parameter leads to the opposite effects.
Applicable Mode: L

THystNormal Additional Meaning: Indicates the extra duration required in the

time evaluation before the UE can enter the normal-mobility state.
hysteresis for This parameter can prevent UEs from frequently switching
normal from the high- or medium-mobility state to the normal-mobility
speed state, and is one of the key parameters in deciding on the UE
mobility. A larger value of this parameter leads to a lower
probability of transition from the high- or medium-mobility state
to the normal-mobility state but higher decision accuracy. A
smaller value of this parameter leads to the opposite effect.
GUI Value Range: S30_T_HYST_NORMAL(30s),
S60_T_HYST_NORMAL(60s),
S120_T_HYST_NORMAL(120s),
S180_T_HYST_NORMAL(180s),
S240_T_HYST_NORMAL(240s)
Unit: s
Actual Value Range: S30_T_HYST_NORMAL,
S60_T_HYST_NORMAL, S120_T_HYST_NORMAL,
S180_T_HYST_NORMAL, S240_T_HYST_NORMAL
MML Default Value: None
Recommended Value: S30_T_HYST_NORMAL(30s)
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
SpeedDepReselCfgInd.
If SpeedDepReselCfgInd is set to CFG, THystNormal must be
set.
If SpeedDepReselCfgInd is set to NOT_CFG, THystNormal
does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A larger value of this
parameter leads to a lower probability of the UE entering the
normal mobility state, a lower probability of adjustment of
reselection-related parameters, and a smaller impact of UE
speed variation on cell reselection.
Applicable Mode: L

NCellChangeMedium The number Meaning: Indicates the threshold of the number of cell
of cell reselections, which is used for a UE to enter the medium
changes to mobility state. This parameter is one of the key parameters in
enter determining the mobility state of the UE. During the UE
medium mobility evaluation, if the number of cell reselections is greater
mobility state than this parameter value and is less than or equal to the
NCellChangeHigh parameter value, the UE enters the medium
mobility state.
GUI Value Range: 1~16
Unit: None
Actual Value Range: 1~16
MML Default Value: None
Recommended Value: 4
Parameter Relationship:
 -Configuration constraints:
In the CellResel MO, if SpeedDepReselCfgInd is set to CFG,
NCellChangeHigh must be greater than NCellChangeMedium.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A larger value of this
parameter indicates a lower probability of a UE entering the
medium mobility state. In this case, the reselection-related
parameters are not adjusted and cell reselections are more
difficult to trigger. A smaller value of this parameter leads to
the opposite effect.
Applicable Mode: L

NCellChangeHigh The number Meaning: Indicates the threshold of the number of cell
of cell reselections, which is used for a UE to enter the high mobility
changes to state. This parameter is one of the key parameters in
enter high determining the mobility state of the UE. During the UE
mobility state mobility evaluation, if the number of cell reselections is greater
than this parameter value, the UE enters the high mobility
state.
GUI Value Range: 1~16
Unit: None
Actual Value Range: 1~16
MML Default Value: None
Recommended Value: 8
Parameter Relationship:
-Configuration constraints:
In the CellResel MO, if SpeedDepReselCfgInd is set to CFG,
NCellChangeHigh must be greater than NCellChangeMedium.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A larger value of this
parameter indicates a lower probability of a UE entering the
high mobility state. In this case, reselection-related
parameters are not adjusted and cell reselections are more
difficult to trigger. A smaller value of this parameter leads to
the opposite effect.
Applicable Mode: L

QHystSfMedium Additional Meaning: Indicates the scaling factor (or known as additional
hysteresis for hysteresis) applied to Qhyst for medium-mobility UEs. For
medium details, see 3GPP TS 36.304 and 3GPP TS 36.331.
speed GUI Value Range: DB_6_Q_HYST_SF_MEDIUM(-6dB),
DB_4_Q_HYST_SF_MEDIUM(-4dB),
DB_2_Q_HYST_SF_MEDIUM(-2dB),
DB0_Q_HYST_SF_MEDIUM(0dB)
Unit: dB
Actual Value Range: DB_6_Q_HYST_SF_MEDIUM,
DB_4_Q_HYST_SF_MEDIUM,
DB_2_Q_HYST_SF_MEDIUM, DB0_Q_HYST_SF_MEDIUM
MML Default Value: None
Recommended Value: DB0_Q_HYST_SF_MEDIUM(0dB)
 Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
SpeedDepReselCfgInd.
If SpeedDepReselCfgInd is set to CFG, QHystSfMedium must
be set.
If SpeedDepReselCfgInd is set to NOT_CFG, QHystSfMedium
does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A smaller value of this
parameter results in a greater impact of the UE mobility state
on the hysteresis for cell reselection, that is, results in a higher
probability of cell reselection. A larger value leads to a smaller
impact.
Applicable Mode: L

QHystSfHigh Additional Meaning: Indicates the scaling factor (or known as additional
hysteresis for hysteresis) applied to Qhyst for high-mobility UEs. For details,
high speed see 3GPP TS 36.304 and 3GPP TS 36.331.
GUI Value Range: DB_6_Q_HYST_SF_HIGH(-6dB),
DB_4_Q_HYST_SF_HIGH(-4dB),
DB_2_Q_HYST_SF_HIGH(-2dB),
DB0_Q_HYST_SF_HIGH(0dB)
Unit: dB
Actual Value Range: DB_6_Q_HYST_SF_HIGH,
DB_4_Q_HYST_SF_HIGH, DB_2_Q_HYST_SF_HIGH,
DB0_Q_HYST_SF_HIGH
MML Default Value: None
Recommended Value: DB0_Q_HYST_SF_HIGH(0dB)
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
SpeedDepReselCfgInd.
If SpeedDepReselCfgInd is set to CFG, QHystSfHigh must be
set.
If SpeedDepReselCfgInd is set to NOT_CFG, QHystSfHigh
does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A smaller value of this
parameter results in a greater impact of the UE mobility state
on the hysteresis for cell reselection, that is, results in a higher
probability of cell reselection. A larger value leads to a smaller
impact.
Applicable Mode: L

SNonIntraSearchCfgI Threshold for Meaning: Indicates whether to configure the measurement

nd non-intra freq triggering threshold for cell reselection to inter-frequency or
measuremen inter-RAT cells. If this parameter is set to NOT_CFG and the
ts configure QQualMinCfgInd parameter is set to NOT_CFG, the UE
indicator continuously measures intra-frequency and inter-RAT cells,
regardless of the signal quality of the serving cell.
 GUI Value Range: NOT_CFG(Not configure), CFG(Configure)
Unit: None
Actual Value Range: NOT_CFG, CFG
MML Default Value: None
Recommended Value: CFG(Configure)
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter will affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

SNonIntraSearch Threshold for Meaning: Indicates the measurement triggering threshold for
non-intra reselection to inter-frequency or inter-RAT cells. If the cell
frequency reselection priority of a frequency or RAT is higher than that of
measuremen the serving frequency, the UEs always start inter-frequency or
ts inter-RAT measurements. If the cell reselection priority of a
frequency is lower than or equal to that of the serving
frequency or if the cell reselection priority of an RAT is lower
than that of the serving frequency, the UEs start inter-
frequency or inter-RAT measurements only when the value of
Cell selection RX level value (dB) is lower than or equal to the
value of this parameter.
GUI Value Range: 0~31
Unit: 2dB
Actual Value Range: 0~62
MML Default Value: None
Recommended Value: 9
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
SNonIntraSearchCfgInd.
If SNonIntraSearchCfgInd is set to CFG, SNonIntraSearch
needs to be set.
If SNonIntraSearchCfgInd is set to NOT_CFG,
SNonIntraSearch does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: With other conditions
unchanged, a larger value of this parameter leads to a higher
probability of triggering inter-frequency or inter-RAT
measurements, and a smaller value indicates a lower
probability.
Applicable Mode: L

ThrshServLow Serving Meaning: Indicates the threshold used in the evaluation of

frequency reselection to a cell on a lower priority E-UTRAN frequency or
lower priority on an inter-RAT frequency. Cell reselection to a cell on a
threshold lower priority E-UTRAN frequency or on an inter-RAT
frequency is performed if no cell on the serving frequency or
on a higher priority E-UTRAN frequency fulfills criteria 1 for
inter-frequency and inter-RAT reselections. For details, see
3GPP TS 36.304.
 GUI Value Range: 0~31
Unit: 2dB
Actual Value Range: 0~62
MML Default Value: None
Recommended Value: 7
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A smaller value of this
parameter indicates a lower frequency of the reselection to a
low priority inter-frequency/inter-RAT cell.
Applicable Mode: L

CellReselPriority Cell Meaning: Indicates the cell reselection priority of the serving
reselection frequency. 0 indicates the lowest priority. The value of this
priority parameter must be determined together with the priorities of
other frequencies during the network planning. Frequencies
used for different RATs must be assigned different cell
reselection priorities.
GUI Value Range: 0~7
Unit: None
Actual Value Range: 0~7
MML Default Value: None
Recommended Value: 7
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter will affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A larger value of this
parameter indicates a higher probability of a UE camping on
the cells assigned with the same frequency as the serving
one, and a smaller value indicates a lower probability.
Applicable Mode: L

QRxLevMin Minimum Meaning: Indicates the minimum required RX level used in

required RX intra-frequency E-UTRAN cell reselection, which corresponds
level to the IE q-RxLevMin in SIB3. This value is included in the cell
reselection criteria and used in the evaluation of cell
reselection. For details, see 3GPP TS 36.304.
GUI Value Range: -70~-22
Unit: 2dBm
Actual Value Range: -140~-44
MML Default Value: None
Recommended Value: -64
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: The greater the
parameter, the more difficult for the cell to meet the S criterion,
the more difficult for the cell to become Suitable Cell. The
difficulty level of the cell selection is increased. The smaller
the parameter, the easier for the cell to meet the S criterion,
 the easier for the cell to become Suitable Cell. The difficulty
level of the cell selection is decreased. The selected cell
should provide the signal quality for the basic services.
Applicable Mode: L

PMaxCfgInd Ue max Meaning: Indicates whether to configure the maximum TX

power power of the UE in the intra-frequency neighboring cell. If the
allowed value of this parameter is not specified, the maximum power is
configure subject to the UE capability.
indicator GUI Value Range: NOT_CFG(Not configure), CFG(Configure)
Unit: None
Actual Value Range: NOT_CFG, CFG
MML Default Value: None
Recommended Value: NOT_CFG(Not configure)
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

PMax Max transmit Meaning: Indicates the maximum power that the UE can apply
power to transmission in the intra-frequency neighboring cell. It is
allowed used in cell reselection criteria to calculate the compensated
power. If the value of this parameter is not specified, the
maximum power is subject to the UE capability. For details,
see 3GPP TS 36.304.
GUI Value Range: -30~33
Unit: dBm
Actual Value Range: -30~33
MML Default Value: None
Recommended Value: 23
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
PMaxCfgInd.
If PMaxCfgInd is set to CFG, PMax must be set.
If PMaxCfgInd is set to NOT_CFG, PMax does not need to be
set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

SIntraSearchCfgInd Threshold for Meaning: Indicates whether to set the measurement triggering
intra freq threshold for reselection to intra-frequency cells.
measuremen GUI Value Range: NOT_CFG(Not configure), CFG(Configure)
ts configure
indicator Unit: None
Actual Value Range: NOT_CFG, CFG
MML Default Value: None
Recommended Value: CFG(Configure)
Parameter Relationship: None
 Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

SIntraSearch Threshold for Meaning: Indicates the measurement triggering threshold for
intra reselection to intra-frequency cells.
frequency The UEs start intra-frequency measurements only if the value
measuremen of Cell selection RX level value (dB) is lower than or equal to
ts the value of this parameter.
GUI Value Range: 0~31
Unit: 2dB
Actual Value Range: 0~62
MML Default Value: None
Recommended Value: 29
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
SIntraSearchCfgInd.
If SIntraSearchCfgInd is set to CFG, SIntraSearch needs to be
set.
If SIntraSearchCfgInd is set to NOT_CFG, SIntraSearch does
not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: With other conditions
unchanged, a larger value of this parameter indicates a higher
probability of triggering intra-frequency measurements, and a
smaller value indicates a lower probability.
Applicable Mode: L

MeasBandWidthCfgI Measuremen Meaning: Indicates whether to set the measurement

nd t bandwidth bandwidth.
configure GUI Value Range: NOT_CFG(Not configure), CFG(Configure)
indicator
Unit: None
Actual Value Range: NOT_CFG, CFG
MML Default Value: None
Recommended Value: NOT_CFG(Not configure)
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

MeasBandWidth Measuremen Meaning: Indicates the measurement bandwidth on the

t bandwidth serving frequency on which the UE camps. It is used in intra-
frequency measurements for cell reselection and those by
UEs in RRC_CONNECTED mode. This parameter is optional;
if it is not set, the downlink bandwidth of the serving cell is
used by default.
GUI Value Range: MBW6(1.4M), MBW15(3M), MBW25(5M),
 MBW50(10M), MBW75(15M), MBW100(20M)
Unit: MHz
Actual Value Range: MBW6, MBW15, MBW25, MBW50,
MBW75, MBW100
MML Default Value: None
Recommended Value: MBW6(1.4M)
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
MeasBandWidthCfgInd.
If MeasBandWidthCfgInd is set to CFG, MeasBandWidth must
be set.
If MeasBandWidthCfgInd is set to NOT_CFG,
MeasBandWidth does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

TReselEutran Cell Meaning: Indicates the evaluation period for a UE to

reselection determine whether to perform cell reselections to a new E-
timer value UTRAN cell. If the signal quality of a new E-UTRAN cell is
for EUTRAN better than that of the serving cell within the period specified
by this parameter and a UE camps on the serving cell for
more than 1s, the UE initiates cell reselections to the new E-
UTRAN cell.
GUI Value Range: 0~7
Unit: s
Actual Value Range: 0~7
MML Default Value: None
Recommended Value: 1
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A smaller value of this
parameter leads to a higher probability of initiating cell
reselections but also a higher probability of ping-pong
reselections. A larger value of this parameter leads to the
opposite effects.
Applicable Mode: L

SpeedStateSfCfgInd Speed state Meaning: Indicates whether to set the scaling parameters for
scale factor speed-dependent cell reselection within E-UTRAN.
configure GUI Value Range: NOT_CFG(Not configure), CFG(Configure)
indicator
Unit: None
Actual Value Range: NOT_CFG, CFG
MML Default Value: None
Recommended Value: CFG(Configure)
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
 mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

TReselEutranSfMedi Scaling Meaning: Indicates the scaling factor applied to TReselEutran

um factor of for medium-mobility UEs. The actual duration of cell
TReselEutra reselection for medium-mobility UEs to E-UTRAN is equal to
n in medium the product of TReselEutran and TReselEutranSfMedium.
mobility state GUI Value Range: T_RESEL_SF_0DOT25(0.25),
T_RESEL_SF_0DOT5(0.5), T_RESEL_SF_0DOT75(0.75),
T_RESEL_SF_1DOT0(1.0)
Unit: None
Actual Value Range: T_RESEL_SF_0DOT25,
T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
T_RESEL_SF_1DOT0
MML Default Value: None
Recommended Value: T_RESEL_SF_1DOT0(1.0)
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
SpeedStateSfCfgInd.
If SpeedStateSfCfgInd is set to CFG, TReselEutranSfMedium
must be set.
If SpeedStateSfCfgInd is set to NOT_CFG,
TReselEutranSfMedium does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A smaller value of this
parameter results in a greater impact of the UE mobility state
on the cell reselection duration within E-UTRAN, that is,
results in a shorter duration. A larger value leads to a smaller
impact.
Applicable Mode: L

TReselEutranSfHigh Scaling Meaning: Indicates the scaling factor applied to TReselEutran

factor of for high-mobility UEs. The actual duration of cell reselection of
TReselEutra high-mobility UEs to E-UTRAN is equal to TReselEutran
n in high multiplied by TReselEutranSfHigh.
mobility state GUI Value Range: T_RESEL_SF_0DOT25(0.25),
T_RESEL_SF_0DOT5(0.5), T_RESEL_SF_0DOT75(0.75),
T_RESEL_SF_1DOT0(1.0)
Unit: None
Actual Value Range: T_RESEL_SF_0DOT25,
T_RESEL_SF_0DOT5, T_RESEL_SF_0DOT75,
T_RESEL_SF_1DOT0
MML Default Value: None
Recommended Value: T_RESEL_SF_0DOT75(0.75)
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of the
SpeedStateSfCfgInd parameter.
If SpeedStateSfCfgInd is set to CFG, TReselEutranSfHigh
must be set.
 If SpeedStateSfCfgInd is set to NOT_CFG,
TReselEutranSfHigh does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: A smaller value of this
parameter results in a greater impact of the UE mobility state
on the actual value of the timer for cell reselection within E-
UTRAN, that is, results in a higher probability of cell
reselection. A larger value leads to a smaller impact.
Applicable Mode: L

NeighCellConfig Neighbor Meaning: Indicates the information related to MBSFN and

Cell TDD UL/DL configurations of intra-frequency neighboring cells
Configuration of the serving cell.
The value 00 indicates that some neighboring cells have the
same MBSFN subframe configuration as the serving cell.
The value 01 indicates that none of the neighboring cells is
configured with MBSFN subframes.
The value 10 indicates that the MBSFN subframe
configurations of all neighboring cells are the same as or
subsets of that of the serving cell.
The value 11 indicates that some neighboring cells have
different UL-DL configurations from the serving TDD cell.
For details, see 3GPP TS 36.331.
GUI Value Range: BitString00(00), BitString01(01),
BitString10(10), BitString11(11)
Unit: None
Actual Value Range: BitString00, BitString01, BitString10,
BitString11
MML Default Value: None
Recommended Value: BitString01(01)
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

PresenceAntennaPor Presence Meaning: Indicates whether all the intra-frequency neighboring

t1 antenna cells are configured with at least two antenna ports.
port1 Set this parameter to BOOLEAN_TRUE when all the intra-
frequency neighboring cells are configured with at least two
antenna ports.
Set this parameter to BOOLEAN_FALSE when one of the
intra-frequency neighboring cells is configured with only one
antenna port.
GUI Value Range: BOOLEAN_FALSE(False),
BOOLEAN_TRUE(True)
Unit: None
Actual Value Range: BOOLEAN_FALSE, BOOLEAN_TRUE
MML Default Value: None
Recommended Value: BOOLEAN_FALSE(False)
Parameter Relationship: None
 Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

SIntraSearchQ RSRQ Meaning: Indicates the RSRQ threshold for starting intra-
Threshold for frequency measurements. It determines the probability of
intra triggering cell reselection to an intra-frequency neighboring
frequency cell. For details, see 3GPP TS 36.304.
measuremen GUI Value Range: 0~31
ts
Unit: dB
Actual Value Range: 0~31
MML Default Value: None
Recommended Value: 5
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: With other conditions
unchanged, a larger value of this parameter indicates a higher
probability of triggering intra-frequency measurements, and a
smaller value indicates a lower probability.
Applicable Mode: L

SNonIntraSearchQ RSRQ Meaning: Indicates the RSRQ threshold for starting inter-
Threshold for frequency or inter-RAT measurements. It determines the
non-intra probability of triggering cell reselection to an inter-frequency or
frequency inter-RAT neighboring cell. For details, see 3GPP TS 36.304.
measuremen GUI Value Range: 0~31
ts
Unit: dB
Actual Value Range: 0~31
MML Default Value: None
Recommended Value: 4
Parameter Relationship: None
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: With other conditions
unchanged, a larger value of this parameter leads to a higher
probability of triggering inter-frequency or inter-RAT
measurements, and a smaller value indicates a lower
probability.
Applicable Mode: L

ThrshServLowQCfgI Serving Meaning: Indicates whether to set the RSRQ threshold for
nd frequency reselection to cells on the serving frequency.
lower priority GUI Value Range: NOT_CFG(Not configure), CFG(Configure)
RSRQ
threshold Unit: None
configure Actual Value Range: NOT_CFG, CFG
indicator MML Default Value: None
Recommended Value: NOT_CFG(Not configure)
Parameter Relationship:
 -Configuration constraints:
In the CellSel, when the QQualMin is set 0, the
ThrshServLowQCfgInd in the CellResel can not be set CFG.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

ThrshServLowQ Serving Meaning: Indicates the RSRQ threshold for cell reselection to
frequency cells on lower-priority frequencies. It determines the probability
lower priority of triggering cell reselection to inter-frequency or inter-RAT
RSRQ neighboring cells on lower-priority frequencies. For details,
threshold see 3GPP TS 36.304.
GUI Value Range: 0~31
Unit: dB
Actual Value Range: 0~31
MML Default Value: None
Recommended Value: 0
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
ThrshServLowQCfgInd.
If ThrshServLowQCfgInd is set to CFG, this parameter must
be set.
If ThrshServLowQCfgInd is set to NOT_CFG, this parameter
does not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: With other conditions
unchanged, a smaller value of this parameter leads to a lower
probability of reselection to an inter-frequency or inter-RAT
cell on lower-priority frequencies, and a larger value of this
parameter leads to a higher probability.
Applicable Mode: L

QQualMinCfgInd Minimum Meaning: Indicates whether to set cell reselection parameters

required in compliance with 3GPP Release 9 in SIB3.
quality level GUI Value Range: NOT_CFG(Not configure), CFG(Configure)
configure
indicator Unit: None
Actual Value Range: NOT_CFG, CFG
MML Default Value: None
Recommended Value: CFG(Configure)
Parameter Relationship:
-Others:
If QQualMinCfgInd is set to CFG, the following cell reselection
parameters in compliance with 3GPP Release 9 in SIB3 will
be
set:SIntraSearchQ,SNonIntraSearchQ,SIntraSearch,SNonIntr
aSearch and QQualMin.
If QQualMinCfgInd is set to NOT_CFG, the following cell
reselection parameters in compliance with 3GPP Release 9 in
SIB3 will not be
 set:SIntraSearchQ,SNonIntraSearchQ,SIntraSearch,SNonIntr
aSearch and QQualMin.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: None
Applicable Mode: L

QQualMin Minimum Meaning: Indicates the minimum required RX signal quality

required used in intra-frequency E-UTRAN cell reselection, which
quality level corresponds to the IE q-QualMin in SIB3. This value is
included in criteria R and used in the evaluation of cell
reselection. For details, see 3GPP TS 36.304.
GUI Value Range: -34~-3
Unit: dB
Actual Value Range: -34~-3
MML Default Value: None
Recommended Value: -18
Parameter Relationship:
-Others:
This parameter is optional, depending on the setting of
QQualMinCfgInd.
If QQualMinCfgInd is set to CFG, this parameter must be set.
If QQualMinCfgInd is set to NOT_CFG, this parameter does
not need to be set.
Service Interrupted After Modification: No (Modifications on
this parameter would affect cell reselection of the UE in idle
mode.)
Impact on Radio Network Performance: With other conditions
unchanged, a smaller parameter value for a cell leads to lower
probabilities of the cell meeting criteria S and becoming a
suitable cell for selection, and a larger parameter value for a
cell leads to higher probabilities. Set this parameter properly
so that the selected cell can provide signals that meet the
quality requirement of basic services.
Applicable Mode: L

Example

Example 1: To modify the parameters about cell reselection as follows:

Local cell ID: 0, Hysteresis value for ranking criteria: DB2_Q_HYST,
Speed-dependent reselection parameter configure indicator: NOT_CFG,
Threshold for non-intra freq measurements configure indicator: CFG,
Threshold for non-intra frequency measurements: 4, Serving frequency
lower priority threshold: 1, Cell reselection priority: 4, Minimum
required RX level: -65, Ue max power allowed configure indicator: CFG,
Max transmit power allowed: -27, Threshold for intra freq measurements
configure indicator: NOT_CFG, Measurement bandwidth configure
indicator: NOT_CFG, Cell reselection timer value for EUTRAN: 5, Speed
state scale factor configure indicator: NOT_CFG, run the following
command:
MOD CELLRESEL: LocalCellId=0, Qhyst=DB2_Q_HYST,
SpeedDepReselCfgInd=NOT_CFG, SNonIntraSearchCfgInd=CFG,
SNonIntraSearch=4, ThrshServLow=1, CellReselPriority=4, QRxLevMin=-65,
PMaxCfgInd=CFG, PMax=-27, SIntraSearchCfgInd=NOT_CFG,
MeasBandWidthCfgInd=NOT_CFG, TReselEutran=5,
SpeedStateSfCfgInd=NOT_CFG;
Example 2: To modify the parameters about cell reselection as follows:
Local cell ID: 0, Hysteresis value for ranking criteria: DB2_Q_HYST,
Speed-dependent reselection parameter configure indicator: CFG, The
duration for evaluating criteria to enter mobility states:
S60_T_EVALULATION, Additional time hysteresis for normal speed:
S60_T_HYST_NORMAL, The number of cell changes to enter medium mobility
state: 3, The number of cell changes to enter high mobility state: 7,
Threshold for non-intra freq measurements configure indicator: NOT_CFG,
Serving frequency lower priority threshold: 1, Cell reselection
priority: 4, Minimum required RX level: -68, Ue max power allowed
configure indicator: NOT_CFG, Threshold for intra freq measurements
configure indicator: NOT_CFG, Measurement bandwidth configure
indicator: CFG, Measurement bandwidth: MBW50, Cell reselection timer
value for EUTRAN: 5, Speed state scale factor configure indicator:
NOT_CFG, run the following command:
MOD CELLRESEL: LocalCellId=0, Qhyst=DB2_Q_HYST,
SpeedDepReselCfgInd=CFG, TEvaluation=S60_T_EVALULATION,
THystNormal=S60_T_HYST_NORMAL, NCellChangeMedium=3, NCellChangeHigh=7,
SNonIntraSearchCfgInd=NOT_CFG, ThrshServLow=1, CellReselPriority

=4, QRxLevMin=-68, PMaxCfgInd=NOT_CFG, SIntraSearchCfgInd=NOT_CFG,

MeasBandWidthCfgInd=CFG, MeasBandwidth=MBW50, TReselEutran=5,
SpeedStateSfCfgInd=NOT_CFG;

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.