800 WATT POWER INVERTER

WITH USB CHARGING PORT
INSTRUCTION MANUAL

Cat. # BDPC750AU September 2016

RD091216 Printed in China
8 1

BDPC750AU_Manual_091216.indd 8-1 9/12/2016 11:56:47 AM

 INSTRUCTION MANUAL Inspection and repairs
• Before use, check the appliance for damaged or
INTENDED USE defective parts. Check for breakage of parts, damage
Your Black & Decker power inverter is designed to to switches and any other conditions that may affect
convert direct current (dc) to alternating current its operation.
(AC). It allows the 12V dc current in an automobile to • Do not use the appliance if any part is damaged or
supply ac power to operate equipment that is normally defective.
supplied from a mains power source. This product is • Have any damaged or defective parts repaired or
replaced by manufacturer.
7 intended for household, consumer use only.
• Never attempt to remove or replace any parts other
SAFETY INSTRUCTIONS than those specified in this manual.
Warning! When using battery-powered appliances, Specific safety instructions for power
basic safety precautions, including the following,
should always be followed to reduce the risk of fire, inverters
leaking batteries, personal injury and material damage. Warning! This appliance converts power from a 12V
dc battery to mains supply voltage. Take precautions,
• Read all of this manual carefully before using the including the following, to avoid the risk of electric
8 appliance. shock.
6 • The intended use is described in this manual. • Only connect a plug fitted to the supply cord of an
The use of any accessory or attachment or the appliance to the inverter.
3 4 5 9 performance of any operation with this appliance
• Never connect an appliance by modifying the plug or
other than those recommended in this instruction
manual may present a risk of personal injury. by using an adapter unless otherwise instructed by
this instruction manual.
• Retain this manual for future reference.
• The length of an appliance power cord to the inverter
2 Using your inverter must not exceed two metres unless otherwise
Always take care when using the inverter. instructed by this instruction manual.
• For indoor or in-car use only. • Never connect an appliance that is damaged or
• This appliance is not intended for use by persons incomplete.
(including children) with reduced physical, sensory • Never connect the inverter to the mains supply or to
or mental capabilities, or lack of experience and the output of another inverter.
knowledge, unless they have been given supervision –– The inverter cannot convert the mains supply
or instruction concerning use of the appliance by a to dc voltage.
person responsible for their safety. –– The inverter cannot be used to supplement
• Children should be supervised to ensure that they do the mains supply.
not play with the appliance. • Do not cover the inverter. Only use in well ventilated
• Use in a dry location only. Do not allow the appliance areas.
11 10 to become wet. Do not immerse the appliance in water. • Do not open the inverter, there are no serviceable
• Do not open body casing. There are no user- parts inside. Do not probe the inverter.
1 serviceable parts inside. • Check that connections to the dc supply are clean
• Do not operate the appliance in explosive and secure. Loose connectors may cause overheated
atmospheres, such as in the presence of flammable wires and melted insulation.
6 liquids, gases or dust. • Check to make sure you have not reversed the polarity.
• To reduce the risk of damage to plugs and cords • Do not install in engine compartments.
never pull the cable to remove the plug from a • Do not use the inverter to supply any medical devices.
socket.
Warning! A reverse polarity connection will result in a
After use blown fuse and may cause permanent damage to the
• When not in use, the appliance should be stored in a power inverter. Damage due to reversed polarity is not
dry, well ventilated place out of the reach of children. covered by the warranty.
• Children should not have access to stored appliances. Warning! Do not use with positive ground electrical
• When the appliance is stored or transported in a systems, (i.e. older vehicles).
vehicle it should be placed in the boot or restrained The power inverter output waveform
to prevent movement following sudden changes in The ac output waveform of this inverter is known
speed or direction. as a “modified sine wave.” This type of waveform
• The appliance should be protected from direct is suitable for most ac loads, including linear
sunlight, heat and moisture. and switching power supplies used in electronic
equipment, transformers, and small motors.
2 3

BDPC750AU_Manual_091216.indd 2-3 9/12/2016 11:56:48 AM

 Warning! Rechargeable devices: Some Specific safety instructions for the   5. Attach the negative ring terminal at the end of the fault icons. If a fault icon appears, refer to the
rechargeable devices do not operate well from a USB power port black battery clip cable to the negative connection “Troubleshooting” section.
modified sine wave inverter. They only operate • Do not insert foreign objects into the USB power post. Replace the connection screw and screw it The USB port is ready to use whenever the converter
correctly from a standard household outlet port. clockwise to secure. Do not over-tighten. is properly connected to a power source. To use the
which provides a pure sine wave. Therefore, the • Do not attach USB hubs or more than one personal   6. Make sure that all connections between cables mains socket, however, the inverter must be properly
manufacturer recommends that you operate these electronic device to the USB power port. and terminals are secure. connected to a power source and the on/off button
types of devices from a standard household outlet Warning! Connect the ring terminals to the terminals must be turned on.
only, not from the inverter. • Some USB-powered household electronics may not
operate with this USB power port. Check the manual of the power inverter before connecting the battery Caution! To reduce the risk of property damage:
This problem does not occur with the majority of of the corresponding electronic device to confirm clips to the battery. Always connect the converter to the 12 volt dc power
battery-operated equipment. Most of these devices use that it can be used with this type of USB power port. Warning! Loose connectors may cause overheated source before plugging any devices into the unit.
a separate charger or transformer that is plugged into wires and melted insulation.
an ac mains socket. The inverter is easily capable of FEATURES The standard mains socket and USB power port allow
running most chargers and transformers. Warning! Check to make sure you have not reversed simultaneous operation of multiple devices. Simply
  1. Battery clamps with cables and ring terminals the polarity. Damage due to reversed polarity is not plug the ac appliance into the inverter’s mains socket
Caution! Incompatible products: Certain products   2. Ventilation slots covered by our warranty. and/or plug the USB-powered device into the inverter’s
contain power supplies or circuits that are not   3. Black (negative) plastic protective cap USB power port and operate normally.
compatible with an inverter using a modified sine wave Power and fault indicators on the LCD
  4. Connection screws (PM6x10) display Notes:
output (such as this inverter) and may be damaged by   5. Red (positive) plastic protective cap
using this inverter. • Ensure that the wattage of all equipment
  6. Mounting brackets (total of 4, 2 in front, 2 in This indicates that simultaneously plugged into the inverter does not
Some products must be powered from a pure sine back) the unit is connected exceed 800 watts continuous.
wave power source, such as standard household   7. Cooling fans properly and
power, or a “pure sine wave” inverter in order to • The inverter will not operate appliances and
  8. LCD Display functioning normally. equipment that generate heat, such as hair dryers,
function properly. If your product requires pure
sine wave ac input power to function properly, the   9. On/Off button This indicates an input electric blankets, microwave ovens and toasters.
instruction manual for your product could state 10. USB power port voltage too low fault • This inverter’s USB Power Port does not support
this. If in doubt, you should contact your product 11. Mains socket condition. Refer to the data communication. It only provides 5 volts/500mA
manufacturer PRIOR TO USE. following section for dc power to an external USB-powered device.
Your product could be damaged by this inverter if it OPERATING INSTRUCTIONS an explanation. • Remember to turn the unit off and disconnect from
contains: Power source requirements any power source when it is not in use.
The power source must provide 12V dc and must be This indicates an Connection to load
• Microwave ovens input voltage too
• Transformerless battery chargers able to supply the necessary current to operate the The power inverter is equipped with a standard mains
load. high fault condition. socket. Plug the cord from the equipment you wish
• Capacitive coupled power supplies Refer to the Protective
Warning! The power inverter must be connected only to operate into the mains socket and/or USB power
If an incompatible product is used with this inverter: Features section for an port. Make sure that the load requirement of your
to batteries with a nominal output voltage of 12 volts. explanation.
• The product might not operate at all, with no The appliance will not operate from a 6 volt battery equipment does not exceed 800 watts.
indication of failure. The product fuse might open as and will sustain permanent damage if connected to a This indicates a The appliance is engineered to be connected directly
a result of trying to use it with the inverter. 24 volt battery. thermal fault condition. to standard electrical and electronic equipment in the
• The product might exhibit unusual operation (such Refer to the Protective manner described above. Do not connect the inverter
as, intermittent operation, buzzing, and the like.) Connecting to a power source
Tools Required: a Philips head screwdriver (NOT Features section for an to household ac wiring. Do not connect the inverter to
Warning! This appliance will not operate high wattage supplied). explanation. any ac load circuit in which the neutral conductor is
appliances or equipment that produce heat, such as connected to ground (earth) or to the negative of the
coffee makers, hair dryers, microwave ovens, and Use the provided battery clips to connect the inverter This indicates a dc (battery) source.
toasters. directly to the 12 volt power source as follows: USB fault condition,
  1. Check to make sure the inverter’s On/Off switch and displays when Warning! Do not connect to ac wiring.
Note: Some laptop computers may not operate with has been turned off and that no flammable fumes the USB load exceeds
this inverter. are present in the installation area. capacity.
PROTECTIVE FEATURES OF THE
Rated versus actual power   2. Open the red (positive) plastic protective cap
POWER INVERTER
requirements of equipment This indicates an Your appliance monitors the following potentially
(downward). Using a Philips head screwdriver, overload or short hazardous conditions:
Most electrical tools, appliances and audio/video unscrew the PM6x10 connection screw
equipment have labels that indicate the power circuit fault condition. Low battery voltage. This condition is not harmful
(counterclockwise) and remove it. Refer to the Protective
consumption in amps or watts. Be sure that the power   3. Attach the positive ring terminal at the end of the to the appliance but could damage the power source.
consumption of the item you wish to operate is rated Features section for an The appliance automatically shuts down when input
red battery clip cable to the positive connection explanation.
at 800 watts or less. post. Replace the connection screw and screw it voltage drops to 10,5 ± 0,5 volts. When the condition
The power inverter is fitted with overload protection clockwise to secure. Do not over-tighten. Operation of the mains socket and is corrected, turn the appliance off and then on.
and will shutdown if a load in excess of 800W is   4. Open the black (negative) plastic protective cap USB power port Over voltage. The power inverter will automatically
applied. Resistive loads (i.e incandescent lights) are (downward). Using a Philips head screwdriver, Refer to “Power and Fault Indicators on the LCD shutdown when the input voltage exceeds 15,5 ± 0,5
the easiest for the power inverter to run. unscrew the PM6x10 connection screw Display” for an explanation of the operating and volts dc.
(counterclockwise) and remove it.
4 5

BDPC750AU_Manual_091216.indd 4-5 9/12/2016 11:56:48 AM

 Short circuit. A reverse polarity or short circuit Television The inverter is shielded to MAINTENANCE If a Baccus Worldwide LLC product becomes
condition may cause external or internal fuses to open Interference From time to time wipe the outside casing of the defective due to faulty materials, workmanship or
and may cause irreversible damage to the appliance. minimize interference with lack of conformity, within 24 months from the date
television signals. However, in inverter with a damp cloth. Do not use any abrasive
Take extra care to insure a correct polarity connection. or solvent-based cleaner. Do not immerse the inverter of purchase, Baccus Worldwide LLC guarantees to
some instances, interference replace defective parts, repair products subjected to
Overload. The power inverter will automatically shut may still occur, particularly in water.
down when the continuous load exceeds 800 watts. Warning! Before performing any maintenance or fair wear and tear or replace such products to make
where television signals sure of the minimum inconvenience to the customer
When the overload is removed, reset the appliance by are weak. Try the following cleaning on the inverter, disconnect it from any power
turning it off and then on again. source. unless:
corrective measures:
Over temperature. If the temperature inside the • The product has been used for trade, professional or
• Place the inverter as far as
appliance is too high, the appliance will automatically possible from the television, PROTECTING THE ENVIRONMENT hire purposes;
shut down. Allow the appliance to cool for at least the aerial or cables. Use Correct disposal of this product • The product has been subjected to misuse or
15 minutes before restarting after a heat-related an extension cable, if This marking indicates that this product neglect;
shutdown. Unplug the appliance while cooling. necessary. should not be disposed with other • The product has sustained damage through foreign
• Readjust the orientation of household waste throughout the EU. To objects, substances or accidents;
HINTS FOR OPTIMUM USE the inverter, the aerial or prevent possible harm to the environment • Repairs have been attempted by persons other than
For best operating results, the inverter should be cables and the television or human health from uncontrolled Baccus Worldwide LLC service staff.
placed on a flat and/or solid surface. The inverter power cord to minimize waste disposal, recycle it responsibly to promote the To claim on this warranty, you will need to submit
should only be used in locations that meet the interference. sustainable reuse of material resources. To return proof of purchase and return the allegedly defective
following criteria: your used device, please use the return and collection product to Baccus Worldwide LLC’s local market
• Make sure the aerial or
DRY – Do not allow water or other liquids to come cable feeding the television systems or contact the retailer where the product distributor, at your expense.
into contact with the inverter. provides an adequate was purchased. They can take this product for Please visit our website www.baccusworldwide.com
COOL – The surrounding air temperature should be (“snow free”) signal and environmentally safe recycling. to register your new Baccus Worldwide LLC product
between 5°C and 40°C. Keep the inverter away from that high quality, shielded Separate collection of used products and packaging and to be kept up to date on new products and special
direct sunlight, when possible. aerial or cable is used. allows materials to be recycled and used again. offers. Further information on the Baccus Worldwide
WELL VENTILATED – Keep the area surrounding • Do not use the inverter Re-use of recycled materials helps prevent LLC brand and our range of products is available at
the inverter clear to ensure free air circulation. Do not to operate high-power environmental pollution and reduces the www.baccusworldwide.com.
place items on or over the inverter during operation. appliances or tools at the demand for raw materials.
The inverter will shut down if the internal temperature same time you are using it Local regulations may provide for separate collection Distributed by: Directed Electronics
gets too hot. Refer to the Protective features section of to operate the television. of electrical products from the household, at municipal Address: 44 Translink Drive, Keilor Park Victoria Australia 3042
this instruction manual for more information. waste sites or by the retailer when you purchase a PH: + 61 03 8331 4800  Email: service@directed.com.au
Common Power Output Problems new product.
SAFE – Do not use the inverter near flammable Baccus Worldwide LLC
materials or in any location that may accumulate Input voltage Recharge auto battery or Weena 290, 3012 NJ Rotterdam or
flammable fumes or gases. This is an electrical below 10,5 volts check dc power supply. TECHNICAL DATA Postbus 819, 3000 AV Rotterdam
Input voltage 12V dc, 78A +31(0)10 282 16 11
appliance that can briefly spark when electrical
connections are made or broken. Equipment being Reduce load to maximum Output voltage 230-240V ac, 50 Hz
operated draws 800 watts. Power output 800 W continuous
TROUBLESHOOTING too much power USB 5V dc, 500mA
Common Audio/Visual Problems Common Power Output Problems Output waveform Modified sine wave

Buzzing Sound In Some inexpensive stereo Inverter in Allow inverter to cool down. WARRANTY
Audio Systems systems make a buzzing thermal shutdown Ensure there is adequate Our goods come with guarantees that cannot be
sound when operated from condition ventilation around the unit excluded under the Australian & New Zealand
an inverter because the and that the load is no Consumer Law. You are entitled to a replacement
power supply in the electronic more than 800 watts for or refund for a major failure and compensation
device does not properly filter continuous operation. for any other reasonably foreseeable loss or
the modified sine wave. The damage. You are also entitled to have the goods
AC output is Unplug the ac appliance. Turn repaired or replaced if the goods fail to be of
only solution to this problem shorted off the inverter. Disconnect
is to use a sound system that acceptable quality and the failure does not
the unit from any 12 volt amount to a major failure.
has a higher quality power dc power source. Check the
supply. Baccus Worldwide LLC is confident of the quality of
appliance cord. its products and offers an outstanding warranty. This
warranty statement is in addition to and in no way
prejudices your statutory rights under the Australian &
New Zealand Consumer Law.

6 7

BDPC750AU_Manual_091216.indd 6-7 9/12/2016 11:56:48 AM