1916098 Page 1 of 1

2008 Suzuki XL-7 AWD | XL-7 (VIN L) Service Manual | Engine | Cruise Control | Schematic and Routing Diagrams |
1916098

Cruise Control Schematics

cardiagn.com

1916098&pubCellSyskey=10758&pub... 12/13/2010
 1707094 Page 1 of 3

2008 Suzuki XL-7 AWD | XL-7 (VIN L) Service Manual | Engine | Cruise Control | Repair Instructions |
1707094

Cruise Release Switch Adjustment

1. Remove the instrument panel left lower closeout panel. Refer to Instrument Panel Insulator
Panel Replacement - Left Side .
2. Remove the knee bolster. Refer to Knee Bolster Replacement .

Notice: Improper cruise control release switch adjustment may cause brake damage such as
brake drag, heat buildup and excessive brake lining wear.

cardiagn.com
3. Disconnect the cruise brake switch harness connector.
4. Rotate the cruise brake switch counterclockwise and remove the cruise brake switch from the
switch retainer.

Important: Do not depress the brake pedal assembly during the brake switch installation.
Depressing the brake pedal will cause a brake drag condition.

1707094&pubCellSyskey=10766&pub... 12/13/2010
 1707094 Page 2 of 3

cardiagn.com
5. Install the cruise brake switch.
• Position the switch into the retainer with the electrical connector index notch pointing to
the 1 o'clock position.
• Slide the switch in the retainer until the plunger is fully depressed into the barrel.
• Rotate the switch clockwise until the travel stop has been reached, approximately
60 degrees.
• Inspect the cruise brake switch to ensure the switch is properly locked into the switch
retainer with the cruise brake switch electrical connector index notch pointing to the
3 o'clock position.

6. Connect the cruise brake switch harness connector.

7. Install the knee bolster. Refer to Knee Bolster Replacement .

1707094&pubCellSyskey=10766&pub... 12/13/2010
 1707094 Page 3 of 3

8. Install the instrument panel left lower closeout panel. Refer to Instrument Panel Insulator
Panel Replacement - Left Side .
9. Use the scan tool to monitor CRUISE BRAKE SWITCH in the engine control module (ECM)
General Information data table, while depressing and releasing the brake pedal. Verify the
APPLIED and RELEASED states read correctly.

cardiagn.com

1707094&pubCellSyskey=10766&pub... 12/13/2010
 1707096 Page 1 of 4

2008 Suzuki XL-7 AWD | XL-7 (VIN L) Service Manual | Engine | Cruise Control | Repair Instructions |
1707096

Cruise Control Release Switch Replacement

Removal Procedure
1. Remove the instrument panel left lower closeout panel. Refer to Instrument Panel Insulator
Panel Replacement - Left Side .
2. Remove the knee bolster. Refer to Knee Bolster Replacement .

cardiagn.com
3. Disconnect the cruise brake switch connector.

4. Rotate the cruise brake switch counterclockwise and remove the cruise brake switch from the
switch retainer.

1707096&pubCellSyskey=10818&pub... 12/13/2010
 1707096 Page 2 of 4

Important: Depressing the brake pedal will allow easier access of the retainer locking tabs.

5. Gently compress the locking tabs on the cruise brake retainer and remove the switch retainer
from the brake pedal assembly.

Installation Procedure
Important: Ensure that the indexing arrow is facing to the right and the ears on the retainer
are fully extended on the back side of the bracket to prevent the retainer from being pushed
out.

cardiagn.com
1. Install the cruise brake switch retainer into the upper hole of the brake pedal assembly with
the retainer arrow pointing in the 3 o'clock position.

Important: Do not depress the brake pedal assembly during the cruise brake switch
installation. Depressing the brake pedal during the cruise brake switch installation will cause
a brake drag condition.

1707096&pubCellSyskey=10818&pub... 12/13/2010
 1707096 Page 3 of 4

cardiagn.com
2. Install the cruise brake switch.
• Position the switch into the retainer with the electrical connector index notch pointing to
the 1 o'clock position.
• Slide the switch in the retainer until the plunger is fully depressed into the barrel.
• Rotate the switch clockwise until the travel stop has been reached, approximately
60 degrees.
• Inspect the cruise brake switch to ensure the switch is properly locked into the switch
retainer with the cruise brake switch electrical connector index notch pointing to the
3 o'clock position.

3. Connect the cruise brake switch harness connector.

4. Install the knee bolster. Refer to Knee Bolster Replacement .

1707096&pubCellSyskey=10818&pub... 12/13/2010
 1707096 Page 4 of 4

5. Install the instrument panel left lower closeout panel. Refer to Instrument Panel Insulator
Panel Replacement - Left Side .
6. Use the scan tool to monitor CRUISE BRAKE SWITCH in the engine control module (ECM)
General Information data table, while depressing and releasing the brake pedal. Verify the
APPLIED and RELEASED states read correctly.

cardiagn.com

1707096&pubCellSyskey=10818&pub... 12/13/2010