Valve amplifier - Wikipedia 6/24/20, 2:20 AM
Valve amplifier
A valve amplifier or tube amplifier is a type of electronic amplifier that
uses vacuum tubes to increase the amplitude or power of a signal. Low to
medium power valve amplifiers for frequencies below the microwaves were
largely replaced by solid state amplifiers in the 1960s and 1970s. Valve
amplifiers can be used for applications such as guitar amplifiers, satellite
transponders such as DirecTV and GPS, high quality stereo amplifiers,
military applications (such as radar) and very high power radio and UHF
television transmitters.
Contents
History
Origins
Post-war developments
Decline An ECC83 tube inside a
Audio usage preamp
Characteristics
Advantages
Disadvantages
Operation
Topologies
Output impedance
Applications
Audio frequency (AF) and broadband amplifiers
Telephony
Audio
Instrumentation amplifiers
Narrow band and radio frequency tuned amplifiers
Notes
See also
References
External links
https://en.wikipedia.org/wiki/Valve_amplifier Page 1 of 9
Valve amplifier - Wikipedia 6/24/20, 2:20 AM
History
Origins
Until the invention of the transistor in 1947, most practical high-frequency electronic amplifiers were
made using thermionic valves.[1] The simplest valve (named diode because it had two electrodes) was
invented by John Ambrose Fleming while working for the Marconi Company in London in 1904. The
diode conducted electricity in one direction only and was used as a radio detector and a rectifier.
In 1906 Lee De Forest added a third electrode and invented the first electronic amplifying device, the
triode, which he named the Audion. This additional control grid modulates the current that flows
between cathode and anode. The relationship between current flow and plate and grid voltage is often
represented as a series of "characteristic curves" on a diagram. Depending on the other components in
the circuit this modulated current flow can be used to provide current or voltage gain.
The first application of valve amplification was in the regeneration of long distance telephony signals.
Later, valve amplification was applied to the 'wireless' market that began in the early thirties. In due
course amplifiers for music and later television were also built using valves.
The overwhelmingly dominant circuit topology during this period
was the single-ended triode gain stage, operating in class A, which
gave very good sound (and reasonable measured distortion
performance) despite extremely simple circuitry with very few
components: important at a time when components were
handmade and extremely expensive. Before World War II, almost
all valve amplifiers were of low gain and with linearity dependent
entirely on the inherent linearity of the valve itself, typically 5%
distortion at full power.
Negative feedback (NFB) was invented by Harold Stephen Black
in 1927, but initially little used since at that time gain was at a
premium. This technique allows amplifiers to trade gain for
reduced distortion levels (and also gave other benefits such as
reduced output impedance). The introduction of the Williamson Circuit diagram of a single-ended
amplifier in 1947, which was extremely advanced in many triode
respects including very successful use of NFB, was a turning point
in audio power amplifier design, operating a push-pull output
circuit in class AB1 to give performance surpassing its contemporaries.
Post-war developments
https://en.wikipedia.org/wiki/Valve_amplifier Page 2 of 9
Valve amplifier - Wikipedia 6/24/20, 2:20 AM
World War II stimulated dramatic technical progress and industrial scale production economies.
Increasing affluence after the war led to a substantial and expanding consumer market. This enabled
electronics manufacturers to build and market more advanced valve (tube) designs at affordable
prices, with the result that the 1960s saw the increasing spread of electronic gramophone players, and
ultimately the beginnings of high fidelity. Hifi was able to drive full frequency range loudspeakers (for
the first time, often with multiple drivers for different frequency bands) to significant volume levels.
This, combined with the spread of TV, produced a 'golden age' in valve (tube) development and also in
the development of the design of valve amplifier circuits.
A range of topologies with only minor variations (notably different phase splitter arrangements and
the "Ultra-Linear" transformer connection for tetrodes) rapidly became widespread. This family of
designs remains the dominant high power amplifier topology to this day for music application. This
period also saw continued growth in civilian radio, with valves being used for both transmitters and
receivers.
Decline
From the 1970s the silicon transistor became increasingly pervasive. Valve production was sharply
decreased, with the notable exception of cathode ray tubes (CRTs), and a reduced range of valves for
amplifier applications. Popular low power tubes were dual triodes (ECCnn, 12Ax7 series) plus the
EF86 pentode, and power valves were mostly being beam tetrode and pentodes (EL84, EL34, KT88 /
6550, 6L6), in both cases with indirect heating. This reduced set of types remains the core of valve
production today.
The Soviets retained valves to a much greater extent than the West during the Cold War, for the
majority of their communications and military amplification requirements, in part due to valves'
ability to withstand instantaneous overloads (notably due to a nuclear detonation) that would destroy
a transistor.[2]
The dramatic reduction in size, power consumption, reduced distortion levels and above all cost of
electronics products based on transistors has made valves obsolete for mainstream products since the
1970s. Valves remained in certain applications such as high power RF transmitters and the microwave
oven, and audio amplification equipment, particularly for the electric guitar, recording studios, and
high-end home stereos.
Audio usage
In audio applications, valves continue to be highly desired by most professional users, particularly in
recording studios' equipment and guitar amplifiers. There is a subgroup of audio enthusiasts who
advocate the use of tube amplifiers for home listening. They argue that tube amplifiers produce a
"warmer" or more "natural" valve sound. Companies in Asia and Eastern Europe continue to produce
valves to cater to this market.
https://en.wikipedia.org/wiki/Valve_amplifier Page 3 of 9
Valve amplifier - Wikipedia 6/24/20, 2:20 AM
Many professional guitar players use 'tube amps' because of their
renowned 'tone'. 'Tone' in this usage is referring to timbre, or pitch
color, and can be a very subjective quality to quantify. Most audio
technicians and scientists theorize that the 'even harmonic distortion'
produced by valve tubes sounds more pleasing to the ear than
transistors, regardless of style. It is the tonal characteristics of valve
tubes that have sustained them as the industry standard for guitars and A single-ended class 'A' guitar
studio microphone pre-amplification. amplifier chassis, with
additional GZ34 valve rectifier
Tube amplifiers respond differently from transistor amplifiers when installed.
signal levels approach and reach the point of clipping. In a tube
amplifier, the transition from linear amplification to limiting is less
abrupt than in a solid state unit, resulting in a less grating form of distortion at the onset of clipping.
For this reason, some guitarists prefer the sound of an all-tube amplifier; the aesthetic properties of
tube versus solid state amps, though, are a topic of debate in the guitarist community.[3]
Characteristics
Power valves typically operate at higher voltages and lower currents than transistors - although solid
state operating voltages have steadily increased with modern device technologies. High power radio
transmitters in use today operate in the kilovolt range, where there is still no other comparable
technology available. ([power = voltage * amperage], so high power requires high voltage, high
amperage, or both)
Many power valves have good linearity but modest gain or transconductance. Signal amplifiers using
tubes are capable of very high frequency response ranges – up to radio frequency and many of the
directly heated single-ended triode (DH-SET) audio amplifiers use radio transmitting tubes designed
to operate in the megahertz range. In practice, however, tube amplifier designs typically "couple"
stages either capacitively, limiting bandwidth at the low end, or inductively with transformers,
limiting the bandwidth at both ends.
Advantages
Very linear (especially triodes) making it preferable to use them in low distortion linear circuits with
little or no negative feedback.[4]
Inherently suitable for high voltage circuits.
Can be constructed on a scale that can dissipate large amounts of heat (some extreme devices
even being water cooled). For this reason valves remained the only viable technology for very
high power applications such as radio and TV transmitters long into the age when transistors had
displaced valves in most other applications.
Electrically very robust, they can tolerate overloads for minutes, which would destroy bipolar
transistor systems in milliseconds
Withstand very high transient peak voltages without damage, suiting them to certain military and
https://en.wikipedia.org/wiki/Valve_amplifier Page 4 of 9
Valve amplifier - Wikipedia 6/24/20, 2:20 AM
industrial applications
Generally operate at applied voltages well below their maximum capability, providing long life and
reliability
Softer clipping when overloading the circuit, which many audiophiles and musicians subjectively
believe gives a more pleasant and more musically satisfying sound.
Disadvantages
Tubes require a cathode heater. Heater power represents a significant heat loss and energy use.
Tubes require higher voltages for the anodes compared to solid state amplifiers of similar power
rating.
Tubes are significantly larger than equivalent solid-state devices
High impedance and low current output is unsuitable for the direct drive of many real-world loads,
notably various forms of electric motors.
Valves have a shorter working life than solid state parts due to various failure mechanisms (such
as heat, cathode poisoning, breakage, or internal short-circuits).
Tubes are available in only a single polarity, whereas transistors are available in complementary
polarities (e.g., NPN/PNP), making possible many circuit configurations that cannot be realized
directly.
Valve circuits must avoid introduction of noise from ac heater supplies.
Microphonics – valves may sometimes be sensitive to sound or vibration, inadvertently acting like
a microphone.
Operation
All amplifier circuits are classified by "class of operation" as A, B, AB and C etc. See power amplifier
classes. Some significantly different circuit topologies exist compared to transistor designs.
The grid (where the input signal is presented) needs to be biased substantially negative with
respect to the cathode. This makes it extremely difficult to directly couple the output of one valve
to the input of a following valve as is normally done in transistor designs.
Valve stages are coupled with components rated to withstand several hundred volts, typically a
capacitor, occasionally a coupling transformer. The phase shifts introduced by coupling networks
can become problematic in circuits that have feedback.
There is no valve analog of the complementary devices widely used in "totem pole" output stages
of silicon circuits. Push-pull valve topologies therefore require a phase splitter.
The very high output impedance of valves (compared with transistors) usually requires matching
transformers to drive low impedance loads such as loudspeakers or cutting lathe heads. The
transformer is used as the load, in place of the resistor usually used in small-signal and driver
stages. The reflected impedance of the transformer primary at the frequencies in use is much
higher than the DC resistance of the windings, often kilohms. High performance transformers are,
however, severe engineering compromises, are expensive and, in operation, are far from ideal.
https://en.wikipedia.org/wiki/Valve_amplifier Page 5 of 9
Valve amplifier - Wikipedia 6/24/20, 2:20 AM
Output transformers dramatically increase the cost of a valve amplifier circuit compared to a
direct-coupled transistor alternative. However, in both tube and solid state amps, matching output
transformers are required for public address applications where low-loss high impedance/high
voltage lines are used to connect multiple distant loudspeakers.
The open loop linearity of valves, especially triodes, makes it possible to use little or no negative
feedback in circuits whilst retaining acceptable or even excellent distortion performance
(especially for small-signal circuits).
Topologies
Linear small signal circuits almost invariably use a triode in the single ended gain stage topology
(in class A), including the output stage.
Broadband valve amplifiers typically use class A1 or AB1.
Modern high power output stages are usually push pull, often necessitating some form of phase
splitter to derive a differential/balanced drive signal from a single ended input, typically followed by
a further gain stage (the "driver") prior to the output tubes. For example, a shunt regulated push-
pull amplifier)
single ended power stages using very large valves exist and dominate in radio transmitter
applications. A sidebar is the observation that the niche "DH-SET" topology favored by some
audiophiles are extremely simple and typically constructed using valve types originally designed
for use in radio transmitters
more complex topologies (notably the use of active loads) can improve linearity and frequency
response (by removing Miller capacitance effects).
Output impedance
The high output impedance of tube plate circuits is not well matched to low-impedance loads such as
loudspeakers or antennas. A matching network is required for efficient power transfer; this may be a
transformer at audio frequencies, or various tuned networks at radio frequencies.
In a cathode follower or common-plate configuration, the output is taken from the cathode
resistance. Because of negative feedback (the cathode-ground voltage cancels the grid-ground voltage)
the voltage gain is close to unity and the output voltage follows the grid voltage. Although the cathode
resistor can be many kilohms (depending on biasing requirements), the small-signal output
impedance is very low (see operational amplifier).
Applications
Audio frequency (AF) and broadband amplifiers
https://en.wikipedia.org/wiki/Valve_amplifier Page 6 of 9
Valve amplifier - Wikipedia 6/24/20, 2:20 AM
Valves remain in widespread use in guitar and high-end audio amplifiers due to the perceived sound
quality they produce. They are largely obsolete elsewhere because of higher power consumption,
distortion, costs, reliability, and weight in comparison to transistors.
Telephony
Telephony was the original, and for many years was a driving application for audio amplification. A
specific issue for the telecommunication industry was the technique of multiplexing many (up to a
thousand) voice lines onto a single cable, at different frequencies.
The advantage of this is that a single valve "repeater" amplifier can amplify many calls at once, this
being very cost effective. The problem is that the amplifiers need to be extremely linear, otherwise
"intermodulation distortion" (IMD) will result in "crosstalk" between the multiplexed channels. This
stimulated development emphasis towards low distortion far beyond the nominal needs of a single
voice channel.
Audio
Today, the main application for valves is audio amplifiers for high-end hi-fi and musical performance
use with electric guitars, electric basses, and Hammond organs, although these applications have
different requirements regarding distortion which result in different design compromises, although
the same basic design techniques are generic and widely applicable to all broadband amplification
applications, not only audio.
Post World War II, the majority of valve power amplifiers are of the Class AB-1 "push pull" ultralinear
topology, or lower cost single ended i.e. 6BQ5/EL84 power tubes, but niche products using the DH-
SET and even OTL topologies still exist in small numbers.
Instrumentation amplifiers
The basic moving coil
voltmeter and ammeter itself
takes a small current and
thus loads the circuit to
which it is attached. This can
significantly alter the
operating conditions in the
A pre-amplifier design using all circuit being measured. The A 300B preamp/solid state output
power tubes instead of small signal vacuum tube voltmeter 70Wrms/ch hybrid amp
tubes
(VTVM) uses the high input
impedance of a valve to
buffer the circuit being measured from the load of the ammeter.
https://en.wikipedia.org/wiki/Valve_amplifier Page 7 of 9
Valve amplifier - Wikipedia 6/24/20, 2:20 AM
Valve oscilloscopes share this very high input impedance and thus can be used to measure voltages
even in very high impedance circuits. There may typically be 3 or 4 stages of amplification per display
channel. In later oscilloscopes, a type of amplifier using a series of tubes connected at equal distances
along transmission lines, known as a distributed amplifier was employed to amplify very high
frequency vertical signals before application to the display tube. Valve oscilloscopes are now obsolete.
In the closing years of the valve era, valves were even used to make "operational amplifiers" – the
building blocks of much modern linear electronics. An op-amp typically has a differential input stage
and a totem pole output, the circuit usually having a minimum of five active devices. A number of
"packages" were produced that integrated such circuits (typically using two or more glass envelopes)
into a single module that could be plugged into a larger circuit (such as an analog computer). Such
valve op-amps were very far from ideal and quickly became obsolete, being replaced with solid-state
types.
Narrow band and radio frequency tuned amplifiers
Historically, pre-WWII "transmitting tubes" were among the most powerful tubes available. These
usually had directly heated thoriated filament cathodes that glowed like light bulbs. Some tubes were
capable of being driven so hard that the anode itself would glow cherry red; the anodes were
machined from solid material (rather than fabricated from thin sheet) to withstand heat without
distorting. Notable tubes of this type are the 845 and 211. Later tetrodes and pentodes such as 817 and
(direct heated) 813 were also used in large numbers in (especially military) radio transmitters
RF circuits are significantly different from broadband amplifier circuits. The antenna or following
circuit stage typically contains one or more adjustable capacitive or inductive component allowing the
resonance of the stage to be accurately matched with carrier frequency in use, to optimize power
transfer from and loading on the valve, a so-called "tuned circuit".
Broadband circuits require flat response over a wide range of frequencies. RF circuits by contrast are
typically required to operate at high frequencies but often over a very narrow frequency range. For
example, an RF device might be required to operate over the range 144 to 146 MHz (just 1.4%)
Today, radio transmitters are overwhelmingly silicon based, even at microwave frequencies. However,
an ever-decreasing minority of high power radio frequency amplifiers continue to have valve
construction.
Notes
1. Solid state devices such as the cat's-whisker detector, copper oxide rectifier, or crystal detector
diode were known before the transistor, but were unable to amplify a signal. Magnetic amplifiers
were limited to below roughly 200kHz. Hydraulic amplifiers were not directly useful as electronic
devices.
2. See Nuclear electromagnetic pulse.
3. Tubes vs Transistors – Is There An Audible Difference? (http://milbert.com/articles/tubes_vs_trans
https://en.wikipedia.org/wiki/Valve_amplifier Page 8 of 9
Valve amplifier - Wikipedia 6/24/20, 2:20 AM
istors)
4. Tubes vs Transistors Feature Comparison (http://milbert.com/articles/tube_transistor_feature_com
parison)
See also
Guitar amplifier
Vintage musical equipment
Klystron
Robert von Lieben
Traveling wave tube
Valve audio amplifier – technical
Valve RF amplifier
Valve transmitters
References
Radio communication handbook (5th Ed), Radio Society of Great Britain, 1976, ISBN 0-900612-
28-2
External links
The Vacuum Tube FAQ (http://www.ken-gilbert.com/techstuff/vtf.html) – Henry Pasternack's FAQ
from rec.audio
The Audio Circuit (http://www.audiocircuit.com/index.php?cc=920) – An almost complete list of
manufacturers, DIY kits, materials and parts and 'how they work' sections on valve amplifiers
Conversion calculator (http://www.sengpielaudio.com/calculator-thd.htm) – distortion factor to
distortion attenuation and THD
AX84.com (http://www.ax84.com) – Although oriented towards valve guitar amplifiers, AX84's free
schematics and theory document apply well to any tube/valve project
Tube Data Archive (http://tubedata.milbert.com) – Massive collection (7 GB+) of tube data sheets
and information.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Valve_amplifier&oldid=948706887"
This page was last edited on 2 April 2020, at 15:48 (UTC).
Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. By using this site,
you agree to the Terms of Use and Privacy Policy. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a
non-profit organization.
https://en.wikipedia.org/wiki/Valve_amplifier Page 9 of 9
