An ISO 9001 Certified Company
mix the ingredients by simple stirring for about 1
AC-PQC-INJECTO min. Motorized or mechanical stirring is not
Low viscous epoxy injection resin necessary.
Fill the injection gun or syringe with AC-PQC-
Description
INJECTO (ensure no entrapment of air in the gun).
Inject the material directly in to the crack. If
AC-PQC-INJECTO is non-shrink, free flow, solvent free, necessary seal the crack and put nozzles and then
low viscosity, high molecular weight, special epoxy. Due carry out injection process.
to low viscosity, it penetrates into cracks and If the injection is done directly into the cracks,
honeycombs in concrete, up to full depth with very less ensure proper method to remove entrapment of air
pressure (or with gravity). in the crack so that epoxy flows into the full depth.
By virtue of low viscosity AC-PQC-INJECTO
Typical Properties
penetrate into the cracks at very low pressure. It
Base : High molecular epoxy
can fill cracks and strengthen concrete matrix.
Mix Proportion : Resin -- - 2 Parts
It has an excellent adhesion with old concrete, Hardener --
- 1 Part
Density : 1 ± 0.1 gm/cm3
repair composite and also possesses resistance to
Compressive : 1 Day --
- 45 N/mm2
chemical. 3 Days --
- 60 N/mm2
strength of mix
As the pot life is up to 60 min., injection process can (N/mm2) IS 9162- 7 Days --
- 75 N/mm2
1979
be done very comfortably.
Flexural strength : 5 N/mm2
AC-PQC-INJECTO is a product of AC-PQC-Road (N/mm2)
Repair System. The system includes 7 products and IS 9162-1979
Pot life : 60 minutes @ 25o C
ACTS Team (Apple Chemie Technical Solution) of
Setting time : 60 minutes @ 25o C
Apple Chemie should be contacted for details.
Viscosity of mix : 100 to 190 cps @ 25oC
Use
For strengthening of honeycombs in concrete.
Standards
For filling of cracks in PQC.
IS-4031-1988, IS 516-1959 and IS 9162-1979.
For repairs near expansion joints in PQC.
Packaging
DIRECTIONS FOR USE/
Kit -- 1 Kg.Resin + 0.5 Kg. Hardener + 0.25 kg. Cleaner
APPLICATION PROCEDURE
+ syringe for injection.
Area to be injected should be cleaned to remove all
loose material.
During the application of AC-PQC-INJECTO ,first stir Storage and Shelf life
the resin and hardener individually in the container Store in sealed container.
and then mix with each other. It is stable for 12 months, if stored in sealed /
Mix AC-PQC-INJECTO resin (2 parts), hardener (1 unopened container.
part). Add hardener into resin (and not reverse) and
1
An ISO 9001 Certified Company
Technical Service
"APPLE CHEMIE" provides technical support service on
evaluation of trials, dispensing equipment etc. Please
contact the Technical department in these cases.
PRECAUTIONS & LIMITATIONS
Exotherm: All epoxy products will develop a
temperature rise on mixing. Its extent will be a
function of the volume to surface ratio, the
ambient temperature as well as the mass and
thermal conductivity of the surrounding
materials. Apple Chemie can be contacted site
suggestions.
It is a performance based product and the
displayed performance depends upon the
quality of the ingredients atmospheric
conditions, e.g., temperature / relative humidity
/ wind speed & direction, etc.
Hence it is recommended that the user carries
out sufficient trials before using the same for
actual intended use.
Safety precaution s
HEALTH AND SAFETY
AC-PQC-INJECTO is non-toxic. Any splashes to the
skin should be washed immediately with water.
Splashes to the eyes should be washed immediately
with water and medical advice should be sought.
Fire: AC-PQC-INJECTO is non-flammable
All possible precautions are taken to manufacture all APPLE CHEMIE PRODUCTS to ensure best quality standards. All products undergo
rigid quality test, however, no guarantee can be given because results depend on many other factors beyond our control. Any verbal or
written recommendation for the product application is intended to support the Buyer / User on the bases if our actual state of scientific and
practical knowledge. They are given in good faith and without any commitment, reserving the rights of third parties or foreign legal
provisions. They do not create any legal relations and no deed of convenient under a sales contract.
It is the Buyer’s / User’s responsibility to find out whether or not our product will fit for the intended use. All transactions shall be subject
to our terms of sale, delivery and payment. We reserve right of changing any / all specifications without any notice.
APPLE CHEMIE INDIA PVT. LTD. 24 ‘Abhang’, Ring Road, Near Chhatrapati Nagar Chowk, Nagpur 440 015. Ph.No. +91-712-2284942,
Fax No. +91-712-2284184 Email : sales@applechemie.com, Visit us at:www.applechemie.com
