Datasheet Version 2.
MAP9000 – High Voltage AC LED Driver
MAP9000
High Voltage AC LED Driver
General Description Features
The MAP9000 is LED Driver which has high input Triac dimming (110Vac/120Vac only)
voltage ranged from 90V to 270V.
Flicker-free
It can drive several series LEDs from rectified AC
voltage. EMI improvement
Power variation: ±15%
The MAP9000 can achieve min 90% efficiency, 0.95 or Constant output power control
higher power factor and low total harmonic distortion Higher power factor : > 0.95
less than 20%. Lower total harmonic distortion : < 20%
Higher current drive capability
The MAP9000 has higher LED current drive capability
up to 240mA and the current can be adjustable with Up to 240mA
external resistors. 6X6mm QFN 12Leads
The MAP9000 is available in 6X6mm QFN 12Leads with
Halogen-free (fully RoHS compliant).
For more information, please contact local MagnaChip Applications
sales office in world-wide or visit MagnaChip’s website.
AC LED Driver
Lighting equipment
LED Driver Power Supplies
Ordering Information
Top Ambient
Part Number Package RoHS Status
Marking Temperature Range
MAP9000QNRH MAP9000 -30℃ to +85℃ 6X6mm QFN 12Leads Halogen Free
AUG 2015 Page 10
Datasheet Version 2.0
MAP9000 – High Voltage AC LED Driver
Simplified Application Circuit
- AC Direct
12 11 10
1 9
2 MAP9000 8
3 7
4 5 6
- Triac Dimming (110Vac/120Vac only)
1KΩ
100nF 12 11 10
1 9
2 MAP9000 8
3 7
4 5 6
- Flicker-free
3.3uF
12 11 10
1 9
2 MAP9000 8
3 7
4 5 6
AUG 2015 Page 10
Datasheet Version 2.0
MAP9000 – High Voltage AC LED Driver
Pin Configuration & Description
- Pin Configuration
12 11 10
Rhold VIN HOLD
1 VCC OUT1 9
2 GND MAP9000OUT2 8
3 N.C OUT3 7
EMI CS MODE
4 5 6
- Pin Description
Pin Descriptions
1 VCC VCC
2 GND Ground
3 N.C No Connection
4 EMI EMI improvement
5 CS Current sensing
6 MODE Flicker-free mode
7 OUT3 Output – 3
8 OUT2 Output – 2
9 OUT1 Output – 1
10 HOLD Holding-up current
11 VIN VCC charging
12 Rhold HOLD turn-on voltage
AUG 2015 Page 10
Datasheet Version 2.0
MAP9000 – High Voltage AC LED Driver
Functional Block Diagram
Bridge
AC
Diode VIN HOLD OUT1 OUT2 OUT3
11 10 9 8 7
VCC
Bandgap
1 &
Ref.
Rhold
Analog Logic & Current Control
12
Line
Shape
1uF
2 3 6 4 5
GND N.C MODE EMI CS
AUG 2015 Page 10
Datasheet Version 2.0
MAP9000 – High Voltage AC LED Driver
Absolute Maximum Ratings
PARAMETER VALUE UNIT
VIN 700 V
HOLD, OUT1, OUT2, OUT3 -0.3 ~ 700 V
EMI -0.3 ~ 6 V
VCC, Rhold, MODE 20 V
Operating Temperature Range -40 ~ 125 ℃
Junction Temperature Range -40 ~ 150 ℃
Storage Temperature Range -65 ~ 150 ℃
Lead Temperature(soldering, 10sec ) 260 ℃
HBM All Pins (Note 1) ±2000 V
ESD Susceptibility MM All Pins (Note 2) ±200 V
CDM All Pins (Note 3) ±1000 V
Note 1: ESD tested per JESD22A-114.
Note 2: ESD tested per JESD22A-115.
Note 3: ESD tested per JESD22C-101E
Thermal Resistance
PARAMETER VALUE UNIT
Thermal Resistance (θJA) , (Note4) 6X6mm QFN 12Leads 63 ℃/W
Thermal Resistance (θJT) , (Note5) 8.7 ℃/W
Note 4: Multi-layer PCB based on JEDEC standard (JESD51-7)
Note 5: The Metal PCB’ diameter is 70mm and height is 1.6t.
AUG 2015 Page 10
Datasheet Version 2.0
MAP9000 – High Voltage AC LED Driver
Electrical Characteristics
Ta = 25℃, CS Resistance = 6.8Ω unless otherwise specified
SYMBOL PARAMETER TEST CONDITION MIN TYP MAX UNIT
Supply
VVIN Input voltage range Note 6 50 700 V
VVCC Operating voltage - 15 - V
IVCC Input current 300 600 900 uA
UVLO_H - 12 - V
VUVLO Under voltage lockout
UVLO_L - 10 - V
Driver Section
Rhold Rhold reference voltage VVIN = 200V, VGND = 0V 5.2 V
VVIN = 200V, VGND = 0V,
ID Leak Driver Leakage current - - 10 uA
HOLD & OUT1 ~ 3 = 400V
VVIN =200V, HOLD = 40V
IHOLD HOLD current 78.3 86.3 94.2 mA
MODE = 0V, Rhold = 0V
VVIN =200V, OUT1 = 40V
IOUT1 Driver 1 current 119.3 128.0 136.7 mA
Rhold = 0V
VVIN =200V, OUT2 = 40V
IOUT2 Driver 2 current 146.0 155.2 164.3 mA
Rhold = 0V
VVIN =200V, OUT3 = 40V
IOUT3 Driver 3 current 178.7 186.2 193.6 mA
Rhold = 0V
IOUT_SUM - IHOLD + IOUT1 + IOUT2 + IOUT3 531.0 556.0 581.0 mA
Note 6: Stress beyond the maximum ratings listed above may incur permanent damage to the device. Operating above the recommended
conditions for extended time may stress the device and affect device reliability. Also the device may not operate normally above
the recommended operating conditions. These are stress ratings only.
AUG 2015 Page 10
Datasheet Version 2.0
MAP9000 – High Voltage AC LED Driver
Typical Operating Characteristics
Iop
180
0.6
160
0.5 140
LED Drive Current (mA)
120
0.4
100
Iop (mA)
0.3
80
0.2
60
IHOLD
0.1 40
IOUT1
20
IOUT2
0.0 IOUT3
0
0 50 100 150 200 0 20 40 60 80 100 120 140 160 180 200
VIN (V) VIN (V)
Operate Current Vs. Input Voltage LED Drive current Vs. Input Voltage
200 800
190
180
700
170
160
150 600
LED Drive Current (mA)
140
130
Iop (uA)
500
120
110
100 400
90
80
300
70
60
50 IHOLD 200
40 IOUT1
30 IOUT2 100
20 IOUT3
10 Iop
0 0
-40 -20 0 20 40 60 80 100 120 140 -20 0 20 40 60 80 100 120 140
o o
Temperature (C ) T e m p e r a t u r) e ( C
LED Drive current Vs. temperature Operate Current Vs. temperature
AUG 2015 Page 10
Datasheet Version 2.0
MAP9000 – High Voltage AC LED Driver
Recommended Surge Protection Circuit
1. Circuit Diagram
The surge test using our demo-board and pass 0.5KV surge voltage at input wattage 16W
10KΩ
2012
Varistor
330VDC/250VAC
1uF 12 11 10
1 9
2 8
MAP9000
3 7
4 5 6
2. Demo-board layout
AUG 2015 Page 10
Datasheet Version 2.0
MAP9000 – High Voltage AC LED Driver
Physical Dimensions
1) QFN 6x6 12LD
MagnaChip Semiconductor Ltd. doesn’t not recommend the use of its products in hostile environments, including, without limitation,
aircraft, nuclear power generation, medical appliances, and devices or systems in which malfunction of any product can reasonably
be expected to result in a personal injury. Seller’s customers using or selling Seller’s products for use in such applications do so at
their own risk and agree to fully defend and indemnify Seller.
MagnaChip reserves the right to change the specifications and circuitry without notice at any time. MagnaChip does not consider
responsibility for use of any circuitry other than circuitry entirely included in a MagnaChip product.
is a registered trademark of MagnaChip Semiconductor Ltd.
MagnaChip Semiconductor Ltd.
891, Daechi-Dong, Kangnam-Gu, Seoul, 135-738 Korea
Tel : 82-2-6903-3451 / Fax : 82-2-6903-3668 ~9
www.magnachip.com
AUG 2015 Page 10
