AT6000 Alcohol Tester
HENAN HANWEI ELECTRONICS CO.,LTD Tel: 86 371 67169070 / 80 Fax: 86 371 67169090
Henan Hanwei Electronics Co.,Ltd www.hwsensor.com
AT6000 Alcohol Tester for Personal Use
Preface
Reminding Before your testing.
Alco Smart Breath tester should be used only to give an indication of the possible presence of
alcohol in the breath/blood. You should not rely upon it as the sole basis to determine intoxication
or whether it is safe to drive a vehicle, operate equipment, or engage in dangerous activities.
Everyone has different body responds to alcohol consumption and his testing result only as
reference, not a subject standard for consequent decision.
The manufacture, importer or distributor takes no responsibility whatsoever for the use of this
product for any reason. This product must not be used as a tool for determining whether a person is
able to operate a motor vehicle or device legally or safely. The intake of any alcohol will impair
reflexes and judgment to operate motor vehicle.
Before your testing, please view the manual carefully and follow the instruction strictly.
General Introduction
AT6000 breath alcohol tester is kind of tester designed to measure concentration result of the
breathed alcohol in the human body. This device adopts advanced NM Hot-wire alcohol sensor which
has excellent sensitivity and reproducibility, fashion and portable design make it more convenient for
personal use. When the alcohol content exceeds the preset limited level, this device would send an
audio and video warning to remind your safety.
Main Feature:
Advanced NM Hot-wire alcohol sensor
Quick response
SMD assembling, stable performance
Smart MCU control
Direct testing process LCD indication
Digital LCD display with light blue backup
Portable and fashion design
Audio warning beyond pre-set limit
Sensor Fault Self checking
Battery saved design, low voltage indication
Technical Data
Sensor type: NM Hot-wire alcohol sensor
Detection Range: 0.00 1.00mg/L (0.00 0.20%BAC; 0.00 2.00g/L; 0.00 2.00‰BAC)
Alarming Level: 0.24mg/L (0.05%BAC, 0.50g/L; 0.50‰BAC)
Accuracy: ±5% F.S
Response Time: 5s Warm-up Time: 20s
Resume Time: ≤20s
Working Voltage: DC4.5V 3×AAA Batteries; Working Current: ≤120mA
Working Environment: Temperature -10 50 Relative Humidity ≤95% No Dews
Display: 3 digits LCD display with light blue backup
Dimension: 103×65×27mm (L×W×H), ≤64 g Battery excluded
Battery expectancy time: ≥200Times
E-mail: sales@hwsensor.com Fax:86-37167169090
Henan Hanwei Electronics Co.,Ltd www.hwsensor.com
1. Structure and Function Guide
1.1 Structure Guide picture 1:
1
1 Mouthpiece
2 Buzzer hole
6
3 Switch Button
5 4 Input for external power
2 5 LCD Screen
4 6 Vent hole
3
Picture 1
1.2. Function Guide
Low Battery Indication
Excessive drinking
Excessive drinking
Indication unit
Testing Result
Warm-up Blow
Test Testing result
Picture 2
Digital Indication:
8.8 8 Alcohol content
20s Countdown Warm-up Countdown
“C” on the LCD ready for blow
000 flash working mode conversion
FFF sensor fault
2. Operation Instruction
2.1. Slide down the battery compartment on the back side, insert 3pcs AAA 1.5V batteries inside
according to battery polarity indication and close it.
2.2. Press the switch button last for 1S, the tester would be on with a buzzer brief ringing, ‘Wait’
flashes and Warm-up of 20 sec begin, the fig on the LCD Countdown from 20-0, please wait now.
Until “Wait” disappears, tester will send out a ring, meantime “BLOW” and “C” gliding, also the small
car icon twinkles, now the test could begin.
2.3. Have a deep breath before testing, and blow directly to gas entry until a buzzer ringing, “000”
E-mail: sales@hwsensor.com Fax:86-37167169090
Henan Hanwei Electronics Co.,Ltd www.hwsensor.com
twinkles for 4S on the screen, at the same time the “BLOW” disappear and ‘TEST’ shown.
2.4. Tester will send out a ring after testing process finished, the LCD screen would give the readout
of temporal alcohol concentration (If the testing result is lower than preset level, only the car icon
twinkles; If the testing result is higher than preset level, the buzzer ringing continuously, at the same
time the “Hi” and “No Driving” icon twinkles), this result would be keep on the screen for 10 sec, then
cut off the power supply automatically with two buzzer ringing.
2.5. If a new testing needed, press the switch button again and repeat the above step 4.2 4.4.
3. Notification
3.1. Avoid any fall or strong shock.
3.2. If noise gas with high concentration existed, may the tester won’t work normally.
3.3. If testing is done under low voltage, certain error will be existed between the real value.
3.4. To ensure the testing result, please wait 10 min to take the testing after your drinking.
3.5. Please operate it strictly according to this instruction. If long time not use, when you first begin a
new testing, the first two times testing result may be unreliable, just begin testing from the third time,
otherwise the result will also not be accurate.
3.6. Do not keep the tester in the environment of Corrosive gas (Chlorine etc) for use or deposit, also
in other bad surroundings.
3.7. Under normal detections, sensor life could be more than two years.
3.8. After Long time use, there may be dirt on the tester, please use clean cloth to wipe off. Do not
use any hard object or the solvent with any Corrosive ingredient.
Remarks: Common Fault and Solving solutions
Fault Possible reason Solution
Incorrect battery Insert battery correctly
installation according to polarity
NO display on LCD
Low battery seriously New battery replacement
Circuit fault Contact distributor
No response to not complete Warm-up Waiting complete Warm-up
detection gas Circuit fault Contact distributor
FFF display then power off Sensor fault Contact distributor
Low voltage display then power off Low battery seriously New battery replacement
To keep the continuous improvement of the products, we reserve the right to improve design without prior notice.
Hanwei
Electronics Co.,Ltd
2006.06
E-mail: sales@hwsensor.com Fax:86-37167169090
HENAN HANWEI ELECTRONICS CORP LIMITED
ALC Nose
AT-126 Breath Alcohol Tester
Reminding Before your testing
Alco Nose Breath tester should be used only to give an indication of the possible presence of alcohol in the breath/blood.
You should not rely upon it as the sole basis to determine intoxication or whether it is safe to drive a vehicle, operate
equipment, or engage in dangerous activities.
Everyone has different body responds to alcohol consumption and his testing result only as reference, not a subject
standard for consequent decision.
The manufacture, importer or distributor takes no responsibility whatsoever for the use of
this product for any reason. This product must not be used as a tool for determining whether a person is able to operate a
motor vehicle or device legally or safely. The intake of any alcohol will impair reflexes and judgment to operate motor vehicle.
Main Features:
Advanced NM hot-wire alcohol sensor;
□Quick response;
□SMD assembling, stable performance;
□MCU control;
□Cartoon and LCD indication, backup light
□Portable and small design
□No Touch Healthy design;
□ Sensor fault self-checking;
Battery saved design, low Volt warning.
Main Technical Info:
Sensor Type: Hot-wire alcohol sensor
Detection Range: 0.00～1.00mg/L(0.00～0.20%BAC；0.00～2.00g/L)
Alarming Level: 0.24mg/L (0.05%BAC; 0.5g/L)
Working Volt: DC3V（2×AAA batteries） Battery using time: ≥60 times
Using Environment: Tem： 0℃～45℃ Relative Hum：≤93% No Dews
Response Time: ＜8S Warm-Up: ＜18S
Indication Manner: 3 digital LCD with cartoon indication
Dimension: l×b×h, 103×37×19 mm ≤45 g
Structure and function Direction
3.2 Function Direction,
shown as Fig 1： Short of Volt
Alcohol Warm up, please wait
concentration Ready for blow
Higher than preset level
Digital Alcohol
results concentration
Units
www.hwsensor.com E-mail: hwsensor@163.com
HENAN HANWEI ELECTRONICS CORP LIMITED
LCD indication：
8.8 8 Breathed alcohol concentration
10S / 18S count down Warm -Up
3S count down Low battery
“C” shown in circle Ready, please blow
“000” shown in flash Turning working manner
FFF Sensor fault
Operation instruction:
4.1 Open the battery room in the back, packed 2 pcs of AAA batteries according to their polarity and close it。
4.2 Press the On/Off switch lasting 1S, backup light would be on following with a brief ringing, then shown (10.9.8 … … 0)
count down, also “WAIT” shown on the upper of LCD screen, now the testers is in Warm-up status, please wait. After
10S W-Up finished, with a ringing, meantime shown “BLOW”, and “C”, now you can start the testing.
4.3 Take a deep breath, then blow to the gas entry slowly with 3-4cm interval until a buzzer ringing for stop, now “000”
flashed in the LCD screen and result comes out.
4.4 The end, testing result would remain 8S, after that the tester would cut off the power with a buzzer ring.
4.5 If a new testing needed, press the “On/Off” switch again, then following the above 4.2 – 4.4 steps instruction.
5. Goblet indication
Above 0.08%BAC 0.05%BAC～0.08%BAC 0.02%BAC～0.05%BAC 0%BAC～0.02%BAC
6. Notification
6.1 Avoid any strong shock and drop to keep the tester in careful package or deposit.;
6.2 Do not wipe it with any cleaning agent, If noise gas exist, the normal testing would be disturbed;
6.3 Avoiding short of Volt batteries used in testing, the result would be not accurate and you need replace new battery;
6.4 It’s better to take testing after 10Mins of drinking for more accurate results;
6.5 After long time storage, If the initial alcohol level of the LCD is on high Level, Please open and close it times to stabilize
until the level is 0.00 in unit.
www.hwsensor.com E-mail: hwsensor@163.com
