Scribd
Upload
70 views11 pages

T910W (En)

This document provides step-by-step instructions for disassembling various components of a Model T910W device. It begins by outlining the necessary tools and screw types used. It then details how to remove the front and rear panels by taking out screws and using various tools to detach connectors. Next, it explains disassembling the buttons by pulling them directly out of the cables. Further sections describe removing the panel by disconnecting cables and lifting out the hinge. The document finishes by providing instructions for taking out the motherboard and power board through removing screws and cables. Troubleshooting tips are included for determining when to replace specific components.

Uploaded by

AN G
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
70 views11 pages

T910W (En)

This document provides step-by-step instructions for disassembling various components of a Model T910W device. It begins by outlining the necessary tools and screw types used. It then details how to remove the front and rear panels by taking out screws and using various tools to detach connectors. Next, it explains disassembling the buttons by pulling them directly out of the cables. Further sections describe removing the panel by disconnecting cables and lifting out the hinge. The document finishes by providing instructions for taking out the motherboard and power board through removing screws and cables. Troubleshooting tips are included for determining when to replace specific components.

Uploaded by

AN G
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

Model Name:T910W

1.Disassembly procedures…2
2.Disassembly tools…………2
3.Screw List…………………3
4.Disassembly of front and
rear panel……………………3
5.Disassembly of buttons……6
6.Disaseembly of panel………7
7.Disassembly of M/B…………9
8.Disassembly of P/B………11

-1-
1.Disassembly Procedures

Front and Panel M/B


Rear panel Disassembly Disassembly
Disassembly
Buttons P/B
Disassembly Disassembly

2.Disassembly tools

Slotted Screwdriver: 3.2 X 75mm

Philips Screwdriver: 5.0 X 100mm

Hex Screwdriver：5m/m

POM Rod

-2-
3. Screw List

1 2 1.Supporting screws

2. Panel screws: Steel rear


panel securing screw

3. Bolt: M/B D-SUB connector

3
4 4. M/B & P/B screws

4. Front and rear panel disassembly

1.Remove the 3 screws


circled in red with the
Philips screwdriver

2.Remove supporting stand


as indicated by the red
arrow.

-3-
3. The red circles indicate
the openings to detach the
panel.

4. Insert the slotted


screwdriver at a 45 degrees
angle into the right opening
to open the panel.

約略 45 度

5. Insert the POM rod at a


45 degrees angle into the
right opening and swipe
towards the right as
indicated by the red arrow
Back facing up remove the
rear panel.

-4-
6. Detached the hinge
circled in red by pulling
backwards. Remove the
buttons by pulling up.

8. Remove front panel.

-5-
5. Disassembly of buttons

1Cables do not have hinge.


Directly pull the buttons
out.

When the below happens, consider


changingthe buttons first
1. NO Power
2. OSD Key Unavailable
3.LED Off

-6-
6. Disassembly of panel

1.Remove the 4 screws


indicated in the red circle
on either sides with the
Philips screwdriver.

2. Use the Slotted


1 2
screwdriver to push down
on the end of the cable
connector as indicated in
pictures 1 and 2 so the
front of the connector lifts
up. At the same time use
your fingers to remove
3
both the cables. (DO NOT
pull the wires). Picture 3
indicates the position of
where to hold the cable
connector.

-7-
3. Lift the steel rear panel
upwards.

4. Push the hinge circled in


red on either side and pull
out the cable.
5. Panel diassembled.

When the below happens, consider changing


the panel first
1. Display White Out
2. Power On No Display.
3. Vertical Line Defect

-8-
7. Disassemble of M/B

1.Remove the 2 bolts with


the Hex screwdriver on
either side.

2.Remove the screw circled


in red with the Philips
screwdriver.

-9-
3.Remove the M/B and
turn it around.
4.There are 3 cables
connected to the M/B. The
3 cables circled in red can
be directly removed by
pulling.

When the below happens, consider changing


the M/B first
1. Power On No Display
2.Power On No Signal
3. Display Shake

-10-
8. Disassembly of P/B

1. Remove the 3 screws


circled in red with the
Philips screwdriver.

2. Remove the P/B.

When the below happens, consider changing


the P/B first.
1.NO Power
2.Power On No Display
3.Display Flicker
-11-

You might also like