TL642
Telehandler
SPECIFICATIONS
Engine Tires
Model Cat ® 3054C Standard 13.00 x 24-12 PR
Gross Power (Basic) 74.5 kW 99 hp Optional 13.00 x 24 Foam Filled
Net Power (Basic) 70.4 kW 94.5 hp 13.00 x 24 Rock Lug
• Net Power shown is the power available at the flywheel
when equipped with fan, air cleaner, muffler, and alternator. Transmission Speeds
Forward 4 speed
Weights Reverse 3 speed
Operating Weight 9180 kg 20,240 lb
Boom Performance
Operating Specifications Boom Up 13 Seconds
Rated Load Capacity 2948 kg 6,500 lb Boom Down 10 Seconds
Maximum Lift Height 12.8 m 42 ft Tele In 13 Seconds
Maximum Forward Reach 9.1 m 30 ft Tele Out 14 Seconds
Frame Leveling 10° Drawbar Pull (Loaded) 8165 kg 18,000 lb
Top Travel Speed 30 kph 20.4 mph
Capacity at Max Height 2948 kg 6,500 lb Axles
Capacity at Max Reach 318 kg 700 lb • Trunnion mounted planetary 55 degree steer axles.
Turning Radius over Tires 3.7 m 12 ft • Integral steer cylinder.
• High bias limited slip differential on front axle.
Hydraulic System — Implement
Gear Pump Single-section Brakes
• Auxiliary Hydraulic Circuit used for all attachments equipped • Service Brakes are inboard wet disc brakes on front axle.
with cylinders or other hydraulic components. Consists of valves, • Parking Brakes are wet disc spring-applied hydraulic release.
controls, and hydraulic lines. Light on dash indicates when brake is on.
Service Refill Capacities Instruments
Fuel Tank 144 L 38 gal • Volt meter, hourmeter, engine oil pressure gauge, fuel gauge, water
Hydraulic System 151.4 L 40 gal temperature gauge. All gauges protected by clear acrylic cover.
Work Tools
Hydraulic IT Coupler Includes Auxiliary Electrics Includes Auxiliary Electrics
Standard Tilt Carriage 1270 mm 50 in
Wide Tilt Carriage 1829 mm 72 in
Pallet Forks (2) 1524 mm, 51 mm x 152 mm (2) 60 in, 2 in x 6 in
(2) 1219 mm, 60 mm x 102 mm (2) 48 in, 2.36 in x 4 in
Cubing Forks (2) 1219 mm, 51 mm x 51 mm (2) 48 in, 2 in x 2 in
Standard Rotate Carriage 1270 mm 50 in
Wide Rotate Carriage 1829 mm 72 in
Swing Carriage 100°, 1829 mm, 4028 kg Capacity, 2268 kg Swung 100°, 72 in, 9,000 lb Capacity, 5,000 lb Swung
Side Shift Carriage 1.22 m 48 in
SPECIFICATIONS TL642 Telehandler
Dimensions
All dimensions are approximate.
TL642
IN M
2.38 m (94 in)
IN
416 mm
MM
(16.4 in)
IN M
2.41 m (95.5 in) IN M
3.25 m (128 in)
IN M
5.63 m (221.6 in)
Load Chart and Dimensions
M FT
IMPORTANT
M FT &
Rated lift capacities shown are with machine
equipped with carriage and pallet forks. The
M FT %
machine must be level on a firm surface with
undamaged, properly inflated tires. Machine
M FT $ specifications and stability are based on rated
lift capacities at specific boom angles and
# boom lengths. (If specifications are critical, the
KG LB
M FT
proposed application should be discussed with
" your dealer.)
M FT
! DO NOT exceed rated lift capacity loads, as
M FT unstable and dangerous machine conditions
KG LB
will result.
KG LB
KG LB
DO NOT tip the machine forward to determine
KG LB
M FT
TL64
the allowable load.
KG LB
M FT Use only JLG approved attachments with
proper material handler model/attachment
M FT load capacity charts displayed in the
operator’s cab. OSHA requires all rough
TL642
M FT
terrain forklift operators be trained
according to OSHA 29 CFR 1910.178 (1).
M FT
Due to continuous product improvements,
M
FT machine specifications and/or equipment
changes may be made without prior
M
FT notification. This machine meets or exceeds
M M M M M M M M M ANSI/ITSDF B56.6-2005 as originally
FT FT FT FT FT FT FT FT FT manufactured for intended applications.
AEHQ5839-01 Printed in U.S.A.
© 2006 Caterpillar All rights reserved.
www.cat.com
CAT, CATERPILLAR, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
