Operating instructions

Vacuum cleaners
S 4000 Series

To avoid the risk of accidents or damage

to the appliance, it is essential to read these
instructions before using it for the first time.
en - GB
These operating instructions apply to
standard models S 4211 - S 4781 as well as to
other S 4000 series vacuum cleaners
which are distinguished by names rather than numbers. M.-Nr. 06 885 930
Contents

Caring for the environment

Description of the appliance
Warning and Safety instructions
Preparing for use
Using the accessories supplied
Use
Mains cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Regulating the suction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Opening the air inlet valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting down, transportation and storage
Maintenance and care
Purchasing new dustbags and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Ordering the correct dustbags and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
When to change the dustbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Replacing the dustbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
When to change the exhaust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Exhaust filter change indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacing the Super Air Clean filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Replacing the Active Air Clean or Active HEPA filter . . . . . . . . . . . . . . . . . . . . . . 26
Replacing one type of filter with another . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
When to change the dust compartment filter (for motor protection) . . . . . . . . . . . 28
How to change the dust compartment filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
When to change the battery in the radio-operated handle . . . . . . . . . . . . . . . . . . 28
How to change the battery in the radio-operated handle . . . . . . . . . . . . . . . . . . . 29
When to change the thread lifters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
To replace the thread lifters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cleaning and care
Problem solving guide / After sales service
Optional accessories
Electrical connection for the UK

2
 Caring for the environment

Disposal of packing material Disposal of your old appliance

The transport and protective packing Electrical and electronic appliances
has been selected from materials which often contain materials which, if
are environmentally friendly for disposal handled or disposed of incorrectly,
and can normally be recycled. could be potentially hazardous to
human health and to the environment.
Ensure that any plastic, wrappings,
They are, however, essential for the
bags etc. are disposed of safely and
correct functioning of your appliance.
kept out of the reach of babies and
Please do not therefore dispose of it
young children. Danger of suffocation.
with your household waste.
Rather than just throwing these
materials away, please recycle them.

Disposing of the dustbag and

filters
These are made from environmentally
friendly materials, and can be disposed
of with the normal household waste, as
long as they have been used Please dispose of it at your local
exclusively for general household dust. community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.

3
Description of the appliance

The illustration shows the maximum number of features available on these Miele
vacuum cleaners.
Certain models are supplied as standard with the following accessories which are
not illustrated on this page.
– ALLERGOTEC floorhead
– Turbobrush
– ACCU NOVA floorhead
These floorheads and brushes are supplied with their own operating instructions.
4
 Description of the appliance
a Handle (some models have an air inlet valve in the handle) *
b Suction power selector + / - *
c Stand-by button for pauses in vacuuming *
d LED *
e Release button
f Accessories holder *
g Release buttons for the telescopic tube *
h Dust compartment release button
i Telescopic tube *
j Dustbag
k Carrying handle
l Floorhead *
m Parking attachment
n Dust compartment filter (for motor protection)
o Exhaust filter *
p Suction power selector *
q Stand-by indicator *
r Overheating warning light , *
s Exhaust filter change indicator (Re-set button) *
t Mains cable
u Foot switch for automatic cable rewind
v Park system
w On/Off foot switch s
x Dustbag change indicator
y Connection socket
z Suction hose

Those features marked * depend on the model, and may vary or not be available
on your model.

5
Warning and Safety instructions
Correct application
This vacuum cleaner meets statutory
This vacuum cleaner must only be
safety requirements. Improper use
used for domestic household
can, however, lead to personal injury
purposes to vacuum dry floor surfaces.
and material damage.
Do not use on people or animals.
To avoid the risk of accidents and
Any other usage, modification or
damage to the vacuum cleaner,
alteration is at the owner's risk and could
read these instructions carefully
be dangerous.
before using it for the first time. They
The manufacturer cannot be held liable
contain important notes on its safety,
for damage resulting from improper or
operation and maintenance.
incorrect use of the appliance.
Keep these instructions in a safe
place and ensure new users are This appliance is not intended for
familiar with the content. Pass them use by persons (including children)
on to any future owner. with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
Always disconnect the vacuum have been given supervision or
cleaner from the mains supply when instruction concerning its use by a
you have finished using it, as well as person responsible for their safety.
for maintenance work and cleaning.
Switch it off at the wall socket and Safety with children
unplug it. If using the ACCU NOVA
powerbrush, switch this off as well. This vacuum cleaner is not a toy!
To avoid the risk of injury, keep
children well away, and do not allow
them to play with it or to use the
controls. Supervise children whilst you
are using it.
Older children may only use the
vacuum cleaner if its operation has
been clearly explained to them, and
they are able to use it safely,
recognising the dangers of incorrect
use.
Models with radio controls on the
handle: Keep batteries out of the
reach of children.

6
 Warning and Safety instructions

Technical safety If the cable is damaged it must be

replaced together with a complete
Ensure that the connection data on
cable rewind. For safety reasons this
the data plate (voltage and
must only be done by the Miele Service
frequency) match the mains electricity
Department or a Miele authorised ser-
supply. It is essential that they match to
vice technician.
avoid damage to the appliance.
While the vacuum cleaner is under
The plug must be fitted with a 13 A
guarantee, repairs should only be
fuse (UK).
undertaken by a service technician
Before using the vacuum cleaner, authorised by Miele. Otherwise the
check for any signs of damage. Do guarantee will be invalidated.
not use a damaged appliance: it could
Repairs should only be carried out
be dangerous.
by a Miele authorised service
There is a metal inlay underneath technician. Repairs and other work by
the handle which is designed to unqualified persons could be
avoid the unpleasant effects of dangerous. The manufacturer cannot
electrostatic discharges. Please make be held liable for unauthorised work.
sure that you keep your hand in
It is important to switch the vacuum
constant contact with this metal strip
cleaner off before changing over
during vacuuming.
accessories and floorheads, especially
Do not pull or carry the vacuum an Electro- or Turbobrush.
cleaner by the cable and be
Do not let the vacuum cleaner get
careful not to damage the cable when
wet. Clean only with a dry cloth or
withdrawing the plug from the socket.
slightly damp cloth when disconnected
– Keep the cable away from sharp from the mains supply. If moisture gets
edges and do not let it be squashed, into the appliance, there is a risk of
for example, under a door. electric shock.
– Avoid running the vacuum cleaner
over the cable.
This could damage the cable, plug or
socket and pose a safety hazard. The
appliance must not be used if any of
these have suffered damage.

7
Warning and Safety instructions

Correct use Do not vacuum up items which are

heavy, hard or have sharp edges.
To avoid the risk of damage, do not
They could cause a blockage and
use the vacuum cleaner without the
damage the appliance.
dustbag, dust compartment filter and
exhaust filter in place. Otherwise it Floor attachments, accessories
could get damaged. and tubes must not be used at
head level to avoid the risk of injury,
If a dustbag is not inserted, the
e.g. to eyes and ears.
dust compartment cover does not
normally close. Do not force it. Monitor the change dustbag
indicator and change the dustbag
Do not vacuum up any water, liquid
if necessary. Check the exhaust and
or damp dirt. This will cause major
dust compartment filters at the same
faults and could seriously impair the
time and change them too if necessary.
functioning and electrical safety of the
A full bag or blocked filter will reduce
appliance. Wait until any freshly
the suction power of the cleaner. A
cleaned or shampooed carpets or floor
temperature limiter switches the
coverings are completely dry before
vacuum cleaner off automatically if it
attempting to vacuum.
gets too hot. See "Problem solving
Do not vacuum toner dust. Toner, guide".
such as that used in printers and
Important information on the
photocopiers, can conduct electricity.
handling of batteries (for models
The filter system in the vacuum cleaner
with radio controls on the handle):
may not filter it completely, causing the
toner to be blown back into the room by – Do not use rechargeable batteries.
the fan.
– Do not short circuit or recharge
Do not vacuum up anything which batteries, or throw them into a fire.
has been burning or is still glowing Danger of explosion.
e.g. cigarettes, ashes or coal, whether
– Disposing of batteries: Remove the
glowing or apparently extinguished.
batteries from the radio control
The cleaner might catch fire.
handle and dispose of them in your
Do not vacuum up any inflammable recycling bin. Do not dispose of them
or combustible liquids or gases with the normal household waste.
and do not vacuum in areas where
such substances are stored. The
cleaner might explode.

8
 Warning and Safety instructions

Accessories
In the UK, Miele accessories
including floorheads, filters and
dustbags are available to order from
your Dealer, the Miele Spare Parts
Department or via the internet on
www.miele.co.uk.

To avoid the risk of injury when

vacuuming with a Miele
Electrobrush or Turbobrush, do not
touch the rotating roller brush.
It is not advisable to vacuum
directly with the handle, i.e. without
an accessory attached as the rim could
get damaged and you could hurt
yourself on sharp edges.
Miele vacuum cleaner bags are
disposable and intended to be
used only once. Do not attempt to
re-use. Blocked pores reduce the
efficiency of the cleaner.
To ensure safety only use genuine
Miele dustbags, filters and
accessories. This will ensure optimum
performance of the appliance
throughout its life.

The manufacturer cannot be held

liable for damage caused by
non-compliance with these Warning
and Safety instructions.

9
Preparing for use

Attaching the suction hose

^ Insert the hose connector into the
socket until it clicks into position. To
do this, line up the guides on the two
pieces.

To remove the suction hose

from the cleaner
^ Press the release buttons at the side
of the hose connector, and lift the
hose from the socket.

Connecting the handle to the

suction tube
^ Insert the handle into the suction tube
until it clicks into position. To do this,
line up the guides on the two pieces.
^ To release the handle from the
suction tube, press the locking button
(see arrow) and pull the handle away
from the suction tube.

10
 Preparing for use
Your vacuum cleaner is fitted with one
of the following types of suction tube,
depending on the model:
– Connecting tubes (fixed height)
– 2-part telescopic tube
– Triscopic telescopic tube

Connecting the 2-part fixed

height tubes
Both sections of the suction tube have
locating arrows marked on them. When
connecting the two sections, ensure that
the two arrows point towards each other.

Adjusting the telescopic

suction tube
One part of this telescopic tube is
packed inside the other and can be
adjusted to suit your height for
comfortable vacuum cleaning.
^ Press the telescopic tube release
button (see arrow) to release the tubes
and adjust to the required height.

Adjusting the triscopic suction

tube
The triscopic tube has three sections.
Two sections of the telescopic tube are
packed together inside a third outer tube.
^ Press the release button (see arrow
a) to release the lower tube and pull
it right out until it clicks. Press the
button again when you want to retract
the tube again. The tube will click into
place.
^ Press the telescopic tube release
button b to release the tubes and
adjust to the required height.

11
Preparing for use

Fitting the standard floorhead

^ Push the suction tube into the
floorhead and turn it clockwise or
anti-clockwise until it clicks into
position.
^ To release the floorhead from the
suction tube, press the locking button
(see arrow) and pull the suction tube
away from the floorhead.
The floorhead can be used for all normal
cleaning of carpets and rugs. It can also
be used with the brush protruding to
vacuum hard flooring. For hard flooring,
such as stone and parquet, we
recommend using one of the special
Miele floor brushes (see "Optional
extras").

It is also important to observe the

flooring manufacturer’s cleaning and
care instructions.

Vacuum carpets and rugs with the

brush retracted:
^ Press the foot switch ö.
Clean hard flooring which is not
susceptible to scratching with the brush
protruding:
^ Press the foot switch ä.

The ALLERGOTEC floorhead, the

ACCU NOVA floorhead and the
Turbobrush
Some models may be supplied as stan-
dard with one of these accessories (see
"Optional accessories"). Please refer to
the separate operating instructions
supplied with these brushes for
instructions on use and maintenance.

12
 Using the accessories supplied
The following accessories are supplied:
a Crevice nozzle
b Dusting brush (depending on model)
c Upholstery nozzle
d Accessory holder for 2 or 3 of the
above accessories
e Filter grille
The filter grille is supplied in the box
with models which are fitted with Active
Air Clean or Active HEPA filters as
standard. You will need to fit it if you
wish to replace one of these filters with
a Super Air Clean filter (see
"Maintenance and care - Replacing the
exhaust filter").

Crevice nozzle
For cleaning in folds, crevices or
corners.

Dusting brush
(supplied with some models)
For cleaning skirting boards, ornate or
carved articles, etc.
The head of the dusting brush can be
swivelled to attain the best cleaning
position.

Dusting brush with natural

bristles
(supplied with some models)
This brush is suitable for particularly
delicate objects.

13
Using the accessories supplied

Upholstery nozzle
For cleaning upholstery, mattresses,
cushions, curtains, covers etc.

Accessories holder
^ Attach the accessories holder to the
upper part of the suction tube when
required.

Floorhead
For general use and also for vacuuming
the stairs.

14
 Use

Mains cable
Unwinding the cable
^ Pull out the mains cable to the
required length (max. approx. 5.5 m).

Warning: If vacuuming for longer

than 30 minutes, the mains cable
must be pulled out to its fullest
extent. Otherwise there is a danger
of overheating and damage.

Rewinding the cable

^ Switch off at the wall socket and
remove the plug.
^ Press the rewind foot switch. The
cable will rewind automatically.

Switching on and off

^ Step on the On-Off foot switch s.

15
Use
Models with radio controls
Certain models have controls on the
handle which transmit radio signals to
the vacuum cleaner. The stand-by
indicator on the vacuum cleaner will
light up when the vacuum cleaner is
ready to use.
To pause the appliance during
operation:
^ Press the stand-by button on the
handle.

Warning: The stand-by button is

designed to pause the vacuum
cleaner for short periods of time
whilst vacuuming. After vacuuming
the device has to be switched off
and unplugged from the mains
supply.

An LED will indicate each time a button

is pressed on the handle.
At the end of the pause you can do one
of the following:
^ Press the stand-by button again to
switch the vacuum cleaner back on
at the setting you were using before
pausing it.
^ Press the + button to switch the
vacuum cleaner back on using the
highest power setting.
^ Press the - button to switch the
vacuum cleaner back on using the
lowest power setting.

16
 Use

Vacuuming Regulating the suction

^ When vacuuming, pull the cleaner Some models also have symbols on the
behind you on its wheels. You can controls. The symbols indicate the type
stand it upright for vacuuming stairs of use the settings are suitable for.
and curtains etc.
a - curtains, lightweight fabrics
Warning: When vacuuming b - upholstery, cushions
especially fine dust, e.g. sawdust,
c - carpets, rugs and runners
sand, plaster, flour, talcum powder
etc., electrostatic charges build up ( - for daily energy-saving vacuuming
naturally. Under certain conditions
e - lightly soiled rugs and fitted
these charges will be released. To
carpets
avoid the unpleasant effects of these
discharges, a metal inlay has been f - heavily soiled hard flooring, and
incorporated into the underside of for intensive cleaning of carpets
the handle. Please make sure that
The controls vary from model to model.
you keep your hand in constant
The different options are carried out in
contact with this metal strip during sequence.
vacuuming.

17
Use

Rotary selector
^ Turn the suction power selector
manually to the suction power setting
you require.

+ / - foot controls
Press the controls to select the suction
power you require.
^ Press the + control to select a higher
setting.
^ Press the - control to select a lower
setting.

+ / - controls on the handle

(radio-operated)
Press the control until the suction power
you require shows in the display on the
cleaner.
^ Press the + control to select a higher
setting.
^ Press the - control to select a lower
setting.
An LED will indicate each time a button
is pressed on the handle.

18
 Use

Opening the air inlet valve

(not on models with radio-controls on
the handle)
It is easy to reduce the suction power
for a short time, e.g. to prevent rugs or
other objects being sucked into the
vacuum cleaner.
^ Open the air inlet valve far enough to
reduce the suction power.
The floorhead will be easier to
manoeuvre. Close the valve up again
when you are ready to use full power
again.

19
Setting down, transportation and storage

Parking system
A parking system has been designed
for conveniently parking the vacuum
cleaner during pauses.
^ Slot the floorhead into the parking
attachment at the back of the
vacuum cleaner.

Transportation and storage

^ Stand the vacuum cleaner upright
when it is not being used and during
storage.
^ Slot the floorhead downwards into the
parking attachment on the side of the
vacuum cleaner.
This makes the cleaner easier to carry
or store.

20
 Maintenance and care
Purchasing new dustbags and
Warning: Always disconnect the filters
vacuum cleaner from the electrical
supply for maintenance work and for Replacement dustbags and filters can
cleaning. Switch off at the wall be obtained from your local Miele
socket and remove the plug. If using Dealer or directly from the Miele Spare
the ACCU NOVA floorhead, switch Parts Department (see back cover for
this off as well. contact details) or in the UK, via the
internet on www.miele.co.uk.
The Miele filter system consists of three
filters which must be replaced from Ordering the correct dustbags
time to time to ensure that your cleaner and filters
performs efficiently.
When ordering dustbags for this
– Dustbag vacuum cleaner, ask for bags with the
– Exhaust filter code F/J/M.

– Dust compartment filter (for motor A Super Air Clean exhaust filter and a
protection) dust compartment filter are supplied
with every packet of Miele dustbags. If
Warning: To ensure that your you wish to purchase exhaust filters or
vacuum cleaner functions correctly, dust compartment filters separately,
cleans hygienically and gives you please quote the model number of your
many years of trouble-free operation appliance when ordering to ensure you
please only use genuine Miele get the correct items.
approved dustbags and filters. The You can replace the exhaust filter fitted
use of non-Miele approved in the vacuum cleaner with one of the
dustbags and accessories could other Miele exhaust filters if you wish
invalidate your warranty and cause (see "Optional accessories").
damage to your product.

21
Maintenance and care

When to change the dustbag

Change the dustbag when the colour
marker in the dustbag change indicator
fills the display, or sooner if it is no
longer effective (see possible reasons
for this below).

Dustbags are designed for single

use only. Do not attempt to re-use
them as suction would be reduced.

Checking the dustbag change

indicator
^ Attach the standard floorhead to the How the dustbag change indicator
suction tube. Do not use any of the works
other floorheads or attachments as
The dustbag change indicator is set for
they will cause the dustbag change
normal household dust. Normal
indicator to give a false reading.
household dust would contain a mixture
^ Switch the vacuum cleaner on and of dust, hair, carpet fluff, threads, grit
select the highest power setting. etc.
^ Lift the floorhead off the floor a little. If However, if the vacuum cleaner has
the marker completely fills the been used to suck up fine dust, such
dustbag change indicator, you as plaster, brick dust, cement or flour,
should replace the dustbag with a the pores of the dustbag will become
new one. blocked very quickly. This affects the
air permeability of the bag, and the
marker will indicate that the bag is "full"
even when it is not. If this happens you
must still change the dustbag because
suction power will be greatly reduced
by blocked pores in the dustbag.
If, on the other hand, you have
vacuumed up a large amount of hair
and carpet fluff which typically contains
a lot of air, the indicator may fail to
react even though the bag is full. You
should still change it! Both these
extremes can occur.

22
 Maintenance and care

Replacing the dustbag

^ Press the release button for the dust
compartment lid and raise the lid as
far as it will go.

^ To remove the dustbag hold the bag

by the collar and pull it out of its
holder.
The dustbag has a closing flap which
closes automatically when the dustbag
is removed to prevent any dust
escaping.

^ Fit the new dustbag into the holder as

far as it will go. Leave it folded up
when you take it out of the box.
^ Close the dust compartment lid
securely, making sure it clicks into
position. Take care not to trap the
dustbag when doing so.

Warning: The lid will not close

without a dustbag in place, or if the
dustbag is incorrectly fitted. Do not
use force!

23
Maintenance and care

When to change the exhaust

filter
Depending on the model, your vacuum
cleaner will be fitted as standard with
one of the following exhaust filters:
a Super Air Clean filter,
Replace this filter every time you start a
new packet of Miele dustbags. A Super
Air Clean exhaust filter and a dust
compartment filter are supplied with
every packet of Miele dustbags.
b Active Air Clean (black)
c Active HEPA (blue)
These types of filter need to be
changed approx. once a year. Make a
note of the date on the filter.

Exhaust filter change indicator

Certain models are fitted with an
exhaust filter change indicator (reset
control) to show when to change your
Active Air Clean b or Active HEPA c
filter.
The indicator lights up after approx. 50
hours of operation which is equivalent
to about a year of average use. You
can continue vacuuming when the light
comes on. However, the suction power
will be reduced as will the effectiveness
of the filter if it is not replaced in good
time.
The filter change indicator light is
irrelevant if a Super Air Clean filter (a) is
being used, as long as it is replaced
every time a new packet of Miele
dustbags is started. The indicator light
will go out when the reset button is
pressed.

24
 Maintenance and care

Replacing the Super Air Clean

filter
^ Open the dust compartment lid.
^ Release the filter grille and raise it
upwards. Grasp the used Super Air
Clean filter by the clean, unsoiled
section (see arrow) and take it out.

^ Replace it with a new Super Air Clean

filter.
^ Close the filter grille.
^ Close the dust compartment lid
firmly. It should click into place.

25
Maintenance and care

Replacing the Active Air Clean

or Active HEPA filter
^ Open the dust compartment lid.
^ Remove the exhaust filter.

^ Fit the new exhaust filter in position.

^ Close the dust compartment lid
firmly. It should click into place.

Re-setting the exhaust filter change

indicator
If your vacuum cleaner is fitted with an
exhaust filter change indicator, this
needs to be re-set each time the filter is
replaced. To do this the vacuum
cleaner must be connected to the
electricity supply.
^ Press the reset button.
The exhaust filter change indicator
goes out, and resets to zero.

The filter change indicator can only

be reset by pressing the reset
button after the light has come on.
Pressing the button at any other time
will have no effect.

26
 Maintenance and care

Replacing one type of filter

with another
Depending on the model, your vacuum
cleaner will be fitted as standard with
one of the following exhaust filters:
a Super Air Clean filter,
b Active Air Clean (black)
c Active HEPA (blue)

Please note
1. If you wish to replace the Super Air
Clean filter a with an Active Air Clean
filter b or an Active HEPA filter c, it is
essential that you remove the filter
grille* before fitting the new type of
filter.
2. If you wish to replace the Active Air
Clean filter b or the Active HEPA filter c
with a Super Air Clean filter a, then it is
essential that you also fit the filter grille *.
* Filter grille - see "Accessories
supplied".

The exhaust filter indicator light (with

reset button) that is fitted on certain
models is designed to come on
when the Active Air Clean or Active
HEPA filters need to be changed.
The filter change indicator light is
irrelevant if a Super Air Clean filter is
being used, as long as it is replaced
every time a new packet of Miele
dustbags is started. The indicator
light will go out when the reset
button is pressed.

27
Maintenance and care

When to change the dust

compartment filter (for motor
protection)
Replace this filter every time you start a
new packet of dustbags. A dust
compartment filter is supplied with
every packet of Miele dustbags.

How to change the dust

compartment filter
^ Open the dust compartment lid.
^ Unclip the filter frame.
^ Take the old filter out.
^ Replace it with a new one.
^ Close the filter frame.

When to change the battery in

the radio-operated handle
Approx. every 18 months. One 3 V
battery (CR 2032) is required.

The vacuum cleaner can still be

used when the battery has run out or
if there is no battery fitted.

^ Switch the vacuum cleaner on using

the On/Off foot control s. The
vacuum cleaner is ready to use (in
stand-by mode).
^ Press the re-set button for the
exhaust filter change indicator.
The vacuum cleaner can continue to be
used, but only at maximum power.

28
 Maintenance and care

How to change the battery in

the radio-operated handle
^ Open the cover to the battery
compartment on the handle, and
remove the battery.
^ Replace with a new battery, taking
care to fit it the right way round.
^ Replace the cover.
^ Dispose of the old battery responsibly.

When to change the thread

lifters
The thread lifters on the suction inlet to
the floorhead and upholstery nozzle
can be replaced.
Check them from time to time and
replace them if the pile has worn down.

To replace the thread lifters

^ Use a knife or similar object to
remove them from the slots.
^ Fit the new thread lifters.

If threads or hair have wound round

the bearing on the floorhead roller:
a Release the bearing (with bayonet
fitting) using a coin.
b Press the bearing out, and remove.
c Take out the roller.
Remove any threads and hair, replace
the roller and refit the bearing.
Spare parts are available from your
Miele dealer or from the Miele Spare
Parts Department (see back cover for
contact details).

29
Cleaning and care
Dust compartment
Warning: Always disconnect the
The dust compartment can, if
vacuum cleaner from the electricity
necessary, be cleaned using a dry
supply for maintenance work and for
duster, brush or, if available, a second
cleaning. Switch off at the wall
vacuum cleaner to vacuum the dust
socket and remove the plug. If using
out.
the ACCU NOVA floorhead, switch
this off as well.
Warning: Do not let the vacuum
cleaner get wet. If moisture gets into
Vacuum cleaner and accessories
the appliance, there is a risk of
External surfaces of the vacuum electric shock.
cleaner and of the accessories can be
cleaned with a dry or a slightly damp
cloth, or with a proprietary cleaner
suitable for plastic.

E-Cloth
A microfibre "E-Cloth" is available from
the Miele UK Spare Parts Department,
Part Number 98013530, which is
suitable for cleaning surfaces such as
stainless steel, glass, plastic and
chrome without the use of chemicals. It
can be washed 300 times.

Warning: Do not use abrasive

cleaners, glass cleaners or
all-purpose cleaners. Because of
their chemical composition they
could cause serious damage to
plastic components.

30
 Problem solving guide / After sales service
The vacuum cleaner switches off
automatically.

On certain models, the overheating

warning light also comes on.
A temperature limiter switches the
vacuum cleaner off automatically if it
gets too hot. Some models also have a
warning light , which comes on to
indicate that it has overheated.
This can occur if, for instance, large
articles block the suction tube or when
the filter bag is full or contains particles
of fine dust. A heavily soiled exhaust or
dust compartment filter can also be the
cause of overheating. Switch off the
vacuum cleaner using the On-Off
switch s. Disconnect from the
electricity supply. Switch off at the wall
socket and remove the plug.
After removing the cause, wait for
approx. 20 - 30 minutes to allow the
vacuum cleaner to cool down. It can
then be switched on again.

After sales service

In the event of a fault that you cannot
easily remedy, please contact
– your Miele dealer, or
– the nearest Miele Service
Department. (See address on back
page).

Please note that telephone calls may

be monitored and recorded for
training purposes.

31
Optional accessories

In the UK, Miele accessories

including floorheads, filters and
dustbags are available to order from
your Dealer, the Miele Spare Parts
Department or via the internet on
www.miele.co.uk.

Certain models are supplied as stan-

dard with one or more of the following
accessories:

Important: please observe the

flooring manufacturer’s cleaning and
care instructions.

Turbobrush
The Turbobrush is particularly suitable
for vacuuming cut-pile carpeting, and is
operated by the suction power of the
vacuum cleaner. It has a rotating brush
and is very effective at picking up
thread, hairs and fluff.

Hand-held Turbobrush
The hand-held Turbobrush is intended
for vacuuming upholstery, mattresses,
car seats, carpeted stairs and other
areas inaccessible to the standard
Turbobrush.

32
 Optional accessories
ACCU NOVA floorhead
The ACCU NOVA floorhead is driven by
a separate motor, and is particularly
suitable for the intensive cleaning of
heavily soiled textile floor surfaces. It is
very effective at removing deep seated
dirt and preventing areas of frequent
use being trodden into a path.

ALLERGOTEC floorhead
The level of cleanliness of the floor
shows in a colour "traffic light" display
when vacuuming. The ALLERGOTEC
floorhead is designed specially for the
daily hygienic cleaning of all floor
surfaces.

33
Optional accessories
SBB 235-3 Hard floor brush
This brush is designed for use on hard
flooring such as tiled or stone floors.

Parquet floor brush

This brush has natural bristles and is
designed for use on parquet floors and
other surfaces which are susceptible to
scratching such as laminate flooring.

SBB 300-3 swivel-action floorbrush

This brush is suitable for use on all
types of hard flooring and is particularly
good at accessing awkward corners
and niches.

34
 Optional accessories
Universal brush
For dusting books, shelves, etc.

Dusting brush
For cleaning skirting boards, ornate or
carved articles, etc.

Dusting brush with natural bristles

This brush is suitable for particularly
delicate objects.

Radiator brush
(Can only be used if attached to the
crevice nozzle).
For cleaning radiators, narrow shelves
and crevices.

35
Optional accessories
Mattress nozzle
For cleaning upholstery, mattresses,
cushions, curtains, covers etc.

Crevice nozzle (300 mm)

For cleaning in folds, crevices or
corners.

Micro Set
This set is specially designed for
cleaning small objects and difficult to
reach areas (such as PC keyboards,
stereo equipment, intricately carved
furniture and ornaments, models etc).
It consists of:
– Micro-hose with combination nozzle
(crevice nozzle and dusting brush)
– Micro dusting brush
– Micro crevice nozzle
– Angled extension
36
 Optional accessories
CarClean Set Plus
The CarClean Set Plus has been
designed as an accessory for Miele
cylinder vacuum cleaners for valeting
the interior of cars.
It consists of:
– Hand-held Turbobrush
– Micro-hose with combination nozzle
(crevice nozzle and dusting brush)
– Crevice nozzle (300 mm)
These are supplied in a carry case
together with a 3 m long suction hose
with hose clip.

CarClean Set Vario

The CarClean Set Vario has been
designed as an accessory for Miele
and non-Miele cylinder vacuum
cleaners for valeting the interior of cars.
It consists of:
– Hand-held Turbobrush
– Micro-hose with combination nozzle
(crevice nozzle and dusting brush)
– Crevice nozzle (300 mm)
– Adapter for connecting the
accessories to a non-Miele vacuum
cleaner.
These are supplied in a carry case.
This set does not include the 3 m long
suction hose with hose clip.

37
Optional accessories
Active Air Clean filter
A special active charcoal filter, which
removes odours coming from the dirt in
the dustbag, keeping unpleasant
lingering smells to a minimum. There is
no difference in the filtration levels
between the Active Air Clean and
Super Air Clean filters.

Active HEPA filter

A combination filter which complies with
the requirements of EN 1822 HEPA
classification 12. It is able to filter out
very fine particles and micro-organisms.
The active charcoal layer absorbs
odours from the dust collected in the
dustbag. This filter is specially
appropriate for allergy sufferers and
users requiring exceptional standards of
hygiene.
The Active HEPA filter replaces the filter
fitted in the vacuum cleaner.

Do not use aroma capsules in your

cleaner if you use either of these
filters. The charcoal in them will
absorb their aroma, rendering them
ineffective.

38
 Electrical connection for the UK
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
national and local safety regulations
(BS 7671 in the UK).
The voltage and connected load are
given on the data plate located
underneath the vacuum cleaner. Please
ensure that these match the household
mains supply. The fuse rating is quoted
on the plug.
The appliance is supplied with a cable
and moulded plug ready for connection
to a 230-240 V/50 Hz a.c. single phase
supply.

Non-rewireable plugs BS 1363

The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug, (as applicable to the design of
plug fitted).
Replacement fuses should be ASTA
approved to BS1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.

39
Alteration rights reserved / (S4211- S4781) - 1107 M.-Nr. 06 885 930 / 05