Hardware Maintenance Manual

ThinkPad X220 Tablet and X220i Tablet

Note: Before using this information and the product it supports, be sure to read the general information
under “Notices” on page 138.

Fourth Edition (November 2011)

© Copyright Lenovo 2011.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services
Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract
No. GS-35F-05925.
Contents

About this manual. . . . . . . . . . . iii Supervisor password . . . . . . . . . . 39

How to remove the power-on password . . . 39
Chapter 1. Safety information . . . . . . 1 How to remove the hard-disk password . . . 40
General safety . . . . . . . . . . . . . . . . 1 Power management . . . . . . . . . . . . 40
Electrical safety . . . . . . . . . . . . . . . 2 Screen blank mode . . . . . . . . . . . 40
Safety inspection guide . . . . . . . . . . . . 3 Sleep (Standby) mode . . . . . . . . . . 41
Handling devices that are sensitive to electrostatic Hibernation mode . . . . . . . . . . . 41
discharge. . . . . . . . . . . . . . . . . . 3
Symptom-to-FRU index . . . . . . . . . . . 42
Grounding requirements . . . . . . . . . . . . 4
Numeric error codes . . . . . . . . . . 43
Safety notices (multilingual translations) . . . . . . 4
Error messages . . . . . . . . . . . . 47
Laser compliance statement (multilingual
translations) . . . . . . . . . . . . . . . . 16 Beep symptoms . . . . . . . . . . . . 48
No-beep symptoms . . . . . . . . . . . 48
Chapter 2. Important service LCD-related symptoms . . . . . . . . . 49
information . . . . . . . . . . . . . . 23 Intermittent problems . . . . . . . . . . 49
Strategy for replacing FRUs . . . . . . . . . 23 Undetermined problems . . . . . . . . . 49
Strategy for replacing a hard disk drive . . . 24
Important notice for replacing a system Chapter 5. Status indicators . . . . . 51
board . . . . . . . . . . . . . . . . 24
How to use error message . . . . . . . . 24 Chapter 6. Fn key combinations . . . 53
Strategy for replacing FRUs for CTO, CMV, and
GAV . . . . . . . . . . . . . . . . . . . 25 Chapter 7. FRU replacement
Product definition . . . . . . . . . . . . 25 notices . . . . . . . . . . . . . . . . 55
FRU identification for CTO, CMV, and GAV Screw notices . . . . . . . . . . . . . . . 55
products . . . . . . . . . . . . . . . 25 Retaining serial numbers. . . . . . . . . . . 56
Restoring the serial number of the system
Chapter 3. General checkout . . . . . 27 unit . . . . . . . . . . . . . . . . . 56
What to do first . . . . . . . . . . . . . . 27 Retaining the UUID . . . . . . . . . . . 57
Checkout guide . . . . . . . . . . . . . . 28 Reading or writing the ECA information . . . 57
Diagnostics using PC-Doctor for DOS. . . . 28
Lenovo ThinkVantage Toolbox . . . . . . . 31 Chapter 8. Removing and replacing a
PC-Doctor for Windows . . . . . . . . . 31 FRU . . . . . . . . . . . . . . . . . . 59
PC-Doctor for Rescue and Recovery . . . . 31 Before servicing ThinkPad X220 Tablet and X220i
Tablet models . . . . . . . . . . . . . . . 60
FRU tests . . . . . . . . . . . . . . . 31
1010 Digitizer pen . . . . . . . . . . . . . 61
Power system checkout . . . . . . . . . . . 33
1020 Battery pack . . . . . . . . . . . . . 61
Checking the ac power adapter . . . . . . 33
1030 Hard disk drive (HDD) and solid state drive
Checking operational charging . . . . . . 33 (SSD) . . . . . . . . . . . . . . . . . . 62
Checking the battery pack . . . . . . . . 34 1040 DIMM . . . . . . . . . . . . . . . . 64
Checking the backup battery . . . . . . . 34 1050 Hinge caps . . . . . . . . . . . . . . 66
1060 Keyboard . . . . . . . . . . . . . . 66
Chapter 4. Related service 1070 Palm rest . . . . . . . . . . . . . . 69
information . . . . . . . . . . . . . . 37
1080 Backup battery . . . . . . . . . . . . 71
Restoring the factory contents by using Product
Recovery discs . . . . . . . . . . . . . . 37 1090 PCI Express Mini Card for wireless
LAN/WiMAX. . . . . . . . . . . . . . . . 73
Restoring the factory contents by using Recovery
Disc Set . . . . . . . . . . . . . . . . . 37 1100 PCI Express Mini Card for wireless WAN . . 75
Passwords . . . . . . . . . . . . . . . . 39 1110 Bluetooth daughter card . . . . . . . . 76
Power-on password . . . . . . . . . . . 39 1120 Keyboard bezel . . . . . . . . . . . . 77
Hard-disk password. . . . . . . . . . . 39 1130 LCD assembly . . . . . . . . . . . . 79

© Copyright Lenovo 2011 i

1140 DC-in connector, base cover, fan, digitizer LCD FRUs . . . . . . . . . . . . . . . . 124
pen case, and pen switch assembly . . . . . . 82 Keyboard . . . . . . . . . . . . . . . . . 128
1150 System board and ExpressCard slot Miscellaneous parts . . . . . . . . . . . . 129
assemblies . . . . . . . . . . . . . . . . 87
ac power adapter . . . . . . . . . . . . . 130
1160 Speaker assembly . . . . . . . . . . . 89
Power cords . . . . . . . . . . . . . . . 130
1170 mSATA solid state drive . . . . . . . . . 90
Recovery discs . . . . . . . . . . . . . . 131
2010 LCD front bezel . . . . . . . . . . . . 91
Windows XP Professional DVDs . . . . . . 131
2020 Micro-Processor card. . . . . . . . . . 93
Windows XP Tablet (32 bit) DVDs . . . . . 132
2030 Hinge . . . . . . . . . . . . . . . . 94
Windows Vista Business (32 bit) DVDs . . . 132
2040 LCD panel and LCD cable . . . . . . . . 95
Windows Vista Home Basic (32 bit) DVDs . . 133
2050 Integrated camera . . . . . . . . . . . 98
Windows 7 Professional (32 bit) DVDs. . . . 133
2060 LCD rear cover and wireless antenna
cables . . . . . . . . . . . . . . . . . . 99 Windows 7 Ultimate (32 bit) DVDs . . . . . 134
Windows 7 Professional (64 bit) DVDs. . . . 134
Chapter 9. Locations . . . . . . . . 103 Windows 7 Ultimate (64 bit) DVDs . . . . . 135
Front view . . . . . . . . . . . . . . . . 103 Windows 7 Home Basic (32 bit) DVDs. . . . 135
Rear view. . . . . . . . . . . . . . . . . 104 Windows 7 Home Basic (64 bit) DVDs. . . . 136
Rear view (tablet mode) . . . . . . . . . . . 105 Windows 7 Home Premium (32 bit) DVDs . . 136
Bottom view . . . . . . . . . . . . . . . 105 Windows 7 Home Premium (64 bit) DVDs . . 137
Top view (ThinkPad X220 UltraBase) . . . . . . 106 Common service tools . . . . . . . . . . . 138
Bottom view (ThinkPad X220 UltraBase). . . . . 106 Notices . . . . . . . . . . . . . . . . . 138
Electronic emissions notices . . . . . . . 139
Chapter 10. Parts list . . . . . . . . 107 Trademarks . . . . . . . . . . . . . . 139
Overall . . . . . . . . . . . . . . . . . . 108

ii Hardware Maintenance Manual

About this manual
This manual contains service and reference information for the following ThinkPad® products.

ThinkPad X220 Tablet and Machine types (MT) 4294, 4296, 4297, 4298, 4299, 4300, and 4301
X220i Tablet

Use this manual along with the advanced diagnostic tests to troubleshoot problems.

Important:
This manual is intended only for trained service technicians who are familiar with ThinkPad products. Use this
manual along with the advanced diagnostic tests to troubleshoot problems effectively.
Before servicing a ThinkPad product, be sure to read all the information under Chapter 1 “Safety information” on
page 1 and Chapter 2 “Important service information” on page 23.

© Copyright Lenovo 2011 iii

iv Hardware Maintenance Manual
Chapter 1. Safety information
This chapter presents following safety information that you need to be familiar with before you service
a ThinkPad Notebook.
• “General safety” on page 1
• “Electrical safety” on page 2
• “Safety inspection guide” on page 3
• “Handling devices that are sensitive to electrostatic discharge” on page 3
• “Grounding requirements” on page 4
• “Safety notices (multilingual translations)” on page 4
• “Laser compliance statement (multilingual translations)” on page 16

General safety
Follow these rules to ensure general safety:

• Observe good housekeeping in the area of the machines during and after maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that
you think is too heavy for you.
• Do not perform any action that causes hazards to the customer, or that makes the equipment unsafe.
• Before you start the machine, make sure that other service technicians and the customer's personnel are
not in a hazardous position.
• Place removed covers and other parts in a safe place, away from all personnel, while you are servicing
the machine.
• Keep your toolcase away from walk areas so that other people will not trip over it.
• Do not wear loose clothing that can be trapped in the moving parts of a machine. Make sure that your
sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive clip, about 8
centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing.

Attention: Metal objects are good electrical conductors.

• Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device
that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent overheating of internal components. Do not obstruct fan
louvers or cover them with labels or stickers.

© Copyright Lenovo 2011 1

Electrical safety
Observe the following rules when working on electrical equipment.

Important:
Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does
not insulate you when working with live electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease
electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.

• Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical
accident occurs, you can then operate the switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near equipment that has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.

Attention: Another person must be there to switch off the power, if necessary.
– Use only one hand when working with powered-on electrical equipment; keep the other hand in your
pocket or behind your back.

Attention: An electrical shock can occur only when there is a complete circuit. By observing the above
rule, you may prevent a current from passing through your body.
– When using testers, set the controls correctly and use the approved probe leads and accessories for
that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as
metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages; Instructions for these
precautions are in the safety sections of maintenance information. Use extreme care when measuring
high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check that it has been powered off.
• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors,
nongrounded power extension cables, power surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury and machine damage.
• Do not service the following parts with the power on when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
– Similar units to listed above
This practice ensures correct grounding of the units.
• If an electrical accident occurs:

2 Hardware Maintenance Manual

 – Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each
machine was designed and built, required safety items were installed to protect users and service technicians
from injury. This guide addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent hazard could be and
whether you can continue without first correcting the problem.

Consider these conditions and the safety hazards they present:

• Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal
electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware

To determine whether there are any potentially unsafe conditions, use the following checklist at the beginning
of every service task. Begin the checks with the power off, and the power cord disconnected.

Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the external ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the safety of any
non-ThinkPad alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or
other liquids, or signs of fire or smoke damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to
electrostatic discharge(ESD). ESD damage can occur when there is a difference in charge between objects.
Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the
person handling the part are all at the same charge.

Chapter 1. Safety information 3

 Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.

When handling ESD-sensitive parts:

• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your body.
• Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when
you are wearing a wrist strap.
• Use a grounded work mat to provide a static-free work surface. The mat is especially useful when
handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection that meets the specific
service requirement.

Note: The use of a grounding system to guard against ESD damage is desirable but not necessary.

– Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.
– When working on a double-insulated or battery-operated system, use an ESD common ground or
reference point. You can use coax or connector-outside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a certified electrician.

Safety notices (multilingual translations)

The safety notices in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese

DANGER

Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small
parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening
for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.

4 Hardware Maintenance Manual

DANGER

Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery,
recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances
or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result
in ignition or explosion of the battery.

DANGER

The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or
short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the
battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result
in ignition or explosion of the battery.

DANGER

The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized
connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water.
Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate
parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.

DANGER

If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash
the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are
present after washing.

DANGER

To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card.

DANGER

Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to
burn personnel or combustible materials.

Chapter 1. Safety information 5

DANGER

Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the
computer, unplug all power cords from electrical outlets, remove the battery pack, and disconnect any
interconnecting cables.

6 Hardware Maintenance Manual

PERIGO

Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e
outras peças pequenas estejam no lugar e não estejam soltos dentro do computador. Verifique isso sacudindo
o computador e procurando ouvir sons de peças soltas. Peças metálicas ou lascas de metal podem causar
curto-circuito.

PERIGO

Algumas baterias reserva contêm uma pequena quantidade de níquel e cádmio. Não desmonte uma bateria
reserva, recarregue-a, jogue-a no fogo ou na água, ou deixe-a entrar em curto-circuito. Descarte a bateria
conforme requerido pelas leis ou regulamentos locais. Use somente a bateria nas partes listadas apropriadas.
O uso de uma bateria incorreta pode resultar em combustão ou explosão da bateria.

PERIGO

O pacote da bateria contém uma pequena quantidade de níquel. Não o desmonte, jogue-o no fogo ou na
água, ou deixe-o entrar em curto-circuito. Descarte o pacote da bateria conforme requerido pelas leis ou
regulamentos locais. Use somente a bateria nas partes listadas apropriadas ao substituir o pacote da bateria.
O uso de uma bateria incorreta pode resultar em combustão ou explosão da bateria.

PERIGO

Chapter 1. Safety information 7

A bateria de lítio pode causar incêndio, explosão ou graves queimaduras. Não a recarregue, remova seu
conector polarizado, desmonte-a, aqueça-a acima de 100°C (212°F), incinere-a, ou exponha o conteúdo de
sua célula à água. Descarte a bateria conforme requerido pelas leis ou regulamentos locais. Use somente
a bateria nas partes listadas apropriadas. O uso de uma bateria incorreta pode resultar em combustão
ou explosão da bateria.

PERIGO

Se o LCD quebrar e o fluido de dentro dele entrar em contato com seus olhos ou com suas mãos, lave as
áreas afetadas imediatamente com água durante pelo menos 15 minutos. Procure cuidados médicos se algum
sintoma causado pelo fluido surgir após a lavagem.

PERIGO

Para evitar choque elétrico, não remova a capa plástica que protege a parte inferior da placa inversora.

PERIGO

Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode
produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis.

PERIGO

A menos que uma hot swap seja permitida para a FRU que está sendo substituída, faça o seguinte antes de
removê-la: desligue o computador, desconecte todos os cabos de energia das tomadas, remova o pacote de
baterias e desconecte quaisquer cabos de interconexão.

DANGER

Avant de remettre l'ordinateur sous tension après remplacement d'une unité en clientèle, vérifiez que tous les
ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l'unité et assurez-vous
qu'aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer
un court-circuit.

DANGER

8 Hardware Maintenance Manual

Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez
pas, ne les exposez ni au feu ni à l'eau. Ne les mettez pas en court-circuit. Pour les mettre au rebut,
conformez-vous à la réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle de
l'horloge temps réel, veillez à n'utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une
batterie ou une pile inappropriée risque de prendre feu ou d'exploser.

DANGER

La batterie contient du nickel. Ne la démontez pas, ne l'exposez ni au feu ni à l'eau. Ne la mettez pas en
court-circuit. Pour la mettre au rebut, conformez-vous à la réglementation en vigueur. Lorsque vous remplacez
la batterie, veillez à n'utiliser que les modèles cités dans la liste de pièces détachées adéquate. En effet, une
batterie inappropriée risque de prendre feu ou d'exploser.

DANGER

La pile de sauvegarde contient du lithium. Elle présente des risques d'incendie, d'explosion ou de brûlures
graves. Ne la rechargez pas, ne retirez pas son connecteur polarisé et ne la démontez pas. Ne l'exposez pas à
une temperature supérieure à 100°C, ne la faites pas brûler et n'en exposez pas le contenu à l'eau. Mettez la
pile au rebut conformément à la réglementation en vigueur. Une pile inappropriée risque de prendre feu ou
d'exploser.

DANGER

Si le panneau d'affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une
partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des
symptômes persistent après le lavage.

DANGER

Afin d'éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure
de la carte d'alimentation.

DANGER

Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d'une
batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des
brûlures corporelles graves.

Chapter 1. Safety information 9

DANGER

Si le remplacement à chaud n'est pas autorisé pour l'unité remplaçable sur site que vous remplacez,
procédez comme suit avant de retirer l'unité : mettez l'ordinateur hors tension, débranchez tous les
cordons d'alimentation des prises de courant, retirez le bloc de batterie et déconnectez tous les câbles
d'interconnexion.

VORSICHT

Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß
keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß
geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen.

VORSICHT

Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel
und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle oder den IBM Kundendienst ausgetauscht
werden. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt
werden. Die Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der Entsorgung die
örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterie nur
Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann
zu Entzündung oder Explosion führen.

VORSICHT

Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt, wiederaufgeladen, kurzgeschlossen,
oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll
beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt
ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.

VORSICHT

Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren oder schwere Verbrennungen
hervorrufen. Batterien dieses Typs dürfen nicht aufgeladen, zerlegt, über 100°C erhitzt oder verbrannt werden.
Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte
Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll
beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt
ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.

VORSICHT

10 Hardware Maintenance Manual

Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen
für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß
behandelt wird oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und die darin
befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15
Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht werden.

VORSICHT

Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt,
nicht entfernen.

VORSICHT

Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei Kurzschluß oder Erdung genug
Strom abgeben, um brennbare Materialien zu entzünden oder Verletzungen bei Personen hervorzurufen.

VORSICHT

Wenn ein Austausch der FRU bei laufendem Betrieb nicht erlaubt ist, gehen Sie beim Austausch der FRU wie
folgt vor: Schalten Sie den Computer aus, ziehen Sie alle Netzkabel von den Netzsteckdosen ab, entfernen
Sie den Akku und ziehen Sie alle miteinander verbundenen Kabel ab.

Chapter 1. Safety information 11

12 Hardware Maintenance Manual
Chapter 1. Safety information 13
Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y
demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo
agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar
cortocircuitos eléctricos.

Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No las desmonte, ni
recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la normativa local.
Utilice sólo baterías que se encuentren en la lista de piezas. La utilización de una batería no apropiada
puede provocar la ignición o explosión de la misma.

14 Hardware Maintenance Manual

Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue, ni las eche al fuego
o al agua ni las cortocircuite. Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas al sustituir la batería. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.

La batería de repuesto es una batería de litio y puede provocar incendios, explosiones o quemaduras graves.
No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100°C (212°F), ni
la incinere ni exponga el contenido de sus celdas al agua. Deséchela tal como dispone la normativa local.

Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos, lave inmediatamente
las áreas afectadas con agua durante 15 minutos como mínimo. Obtenga atención medica si se presenta
algún síntoma del fluido despues de lavarse.

Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida.

Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra
puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en
el personal.

Salvo que se permita el intercambio en caliente para la unidad sustituible localmente, realice lo siguiente antes
de extraerla: apague el sistema, desconecte todos los cables de alimentación de las tomas de alimentación
eléctrica, extraiga la batería y desconecte los cables de interconexión.

Chapter 1. Safety information 15

Laser compliance statement (multilingual translations)
The laser compliance statements in this section are provided in the following languages:
• English
• Arabic
• Brazilian Portuguese
• French
• German
• Hebrew
• Japanese
• Korean
• Spanish
• Traditional Chinese

16 Hardware Maintenance Manual

Chapter 1. Safety information 17
18 Hardware Maintenance Manual
Chapter 1. Safety information 19
20 Hardware Maintenance Manual
Chapter 1. Safety information 21
22 Hardware Maintenance Manual
Chapter 2. Important service information
This chapter presents following important service information that applies to all machine types supported by
this manual:
• “Strategy for replacing FRUs” on page 23
– “Strategy for replacing a hard disk drive” on page 24
– “Important notice for replacing a system board” on page 24
– “How to use error message” on page 24
• “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 25
– “Product definition” on page 25
– “FRU identification for CTO, CMV, and GAV products” on page 25

Important:
Advise customers to contact the Lenovo Customer Support Center if they need any assistance in obtaining or
installing any software fixes, drivers, and UEFI BIOS downloads. Telephone numbers for Lenovo Support are
available at:
http://www.lenovo.com/support/phone
System Disassembly/Reassembly videos that show the FRU removals or replacements for the Lenovo® authorized
service technicians are available in the following support site:
http://www.lenovoservicetraining.com/ion/

Strategy for replacing FRUs

Before replacing parts:

Make sure that all software fixes, drivers, and UEFI BIOS downloads are installed before replacing any
FRUs listed in this manual.

After a system board is replaced, ensure that the latest UEFI BIOS is loaded to the system board before
completing the service action.

To download software fixes, drivers, and UEFI BIOS, do as follows:

1. Go to http://www.lenovo.com/support.
2. Enter the product number of the computer or press Auto-detect button on the screen.
3. Select Downloads and drivers.
4. Follow the directions on the screen and install the necessary software.

Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs:
• If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall
the original FRU before you continue.
• Some computers have both a processor board and a system board. If you are instructed to replace either
the processor board or the system board, and replacing one of them does not correct the problem,
reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change.
Replace only the FRU that changed the symptoms.

© Copyright Lenovo 2011 23

Attention: The setup configuration on the computer you are servicing may have been customized. Running
Automatic Configuration may alter the settings. Note the current configuration settings (using the View
Configuration option); then, when service has been completed, verify that those settings remain in effect.

Strategy for replacing a hard disk drive

If your computer is shipped with an mSATA drive and a solid state drive or hard disk drive, the mSATA drive
will be seen as hard disk 0 in the system, and assigned drive C:. The solid state drive or hard disk drive will
be seen as hard disk 1, and assigned drive D:. The mSATA drive is installed in the wireless WAN card slot of
the computer. The Lenovo preloaded software is installed on the mSATA drive.

Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on
the hard disk to be lost. Be sure that the customer has a current backup of the data before doing this task.

Attention: The drive startup sequence in the computer you are servicing may have been changed. Be
extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect
drive, data or programs can be overwritten.

Important notice for replacing a system board

Some components mounted on a system board are very sensitive. Improper handling of a system board can
cause damage to those components, and may cause a system malfunction.

Attention: When handling a system board:

• Do not drop a system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.

How to use error message

Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed,
begin the diagnosis with the first error code. Whatever causes the first error code may also cause false error
codes. If no error code is displayed, see whether the error symptom is listed in the Symptom-to-FRU
Index for the computer you are servicing.

24 Hardware Maintenance Manual

Strategy for replacing FRUs for CTO, CMV, and GAV

Product definition

Dynamic Configure To Order (CTO)

This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this
configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label,
Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT
and 3-digit model, where model = “CTO” (Example: 1829-CTO).

Custom Model Variant (CMV)

This is a unique configuration that has been negotiated between Lenovo and the customer. A unique 4-digit
MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15). A CMV is a special
bid offering. Therefore, it is NOT generally announced.
• The MTM portion of the machine label is the 4-digit MT and 3-digit model, where model = “CTO”
(Example: 1829-CTO). The PRODUCT ID portion of the machine label is the 4-digit MT and 3-digit CMV
model (Example: 1829-W15).
• The PEW record is the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
• eSupport will show both the CTO and CMV machine type models (Example: 1829-CTO and 1829-W15
will be found on the eSupport site.)
• The HMM will have the 4-digit MT and 3-digit CTO model only (Example: 1829-CTO). Again, CMVs are
custom models and are not found in the HMM.

General Announce Variant (GAV)

This is a standard model (fixed configuration). GAVs are announced and offered to all customers. The MTM
portion of the machine label is a 4-digit MT and 3-digit model, where model = a “fixed part number”, not
“CTO” (Example: 1829-F1U). Also, PEW, eSupport, and the HMM will list these products under the same
fixed model number.

FRU identification for CTO, CMV, and GAV products

There are three information resources to identify which FRUs are used to support CTO, CMV, and GAV
products. These sources are PEW, eSupport, and the HMM.

Using PEW
• PEW is the primary source for identifying FRU part numbers and FRU descriptions for the key commodities
for CTO, CMV and GAV products at a MT - serial number level. An example of key commodities are hard
disk drives, system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory.
• Remember, all CTO and CMV products are loaded in PEW under the 4-digit MT and 3-digit model, where
model = “CTO” (Example: 1829-CTO). GAVs are loaded in PEW under the 4-digit MT and 3-digit model,
where model = a “fixed part number”, not “CTO” (Example: 1829-F1U).
• PEW can be accessed at the following Web site:
http://www.lenovo.com/support/site.wss/document.do?lndocid=LOOK-WARNTY
Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be
returned in the PEW record under COMPONENT INFORMATION.

Using eSupport
For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory)

Chapter 2. Important service information 25

• eSupport can be used to view the list of key commodities built in a particular machine serial (this is the
same record found in PEW).
• eSupport can be accessed at the following Web site:
http://www.lenovo.com/support
• To view the key commodities, do the following:
1. Click Products & Service Warranty.
2. Click Check Warranty Status.
3. On the Warranty Status Lookup page, click Parts Lookup.
4. Type your machine type and serial number, and then click Submit. The key commodities will be
displayed.

For the Remaining FRUs (the complete list of FRUs at the MT Model level)
• eSupport can be used to view the complete list of FRUs for a machine type and model.
• To view the complete list of FRUs, do the following:
1. Click Product & Parts Detail and then follow the instructions on the screen to reach the Product
and Parts Details page.
2. Click the Parts Detail tab to view the list of service parts.

Using the HMM

For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory)

Use the HMM as a back-up to PEW and eSupport to view the complete list of FRUs at the MT Model level.

26 Hardware Maintenance Manual

Chapter 3. General checkout
This chapter presents following information:
• “What to do first” on page 27
• “Checkout guide” on page 28
– “Diagnostics using PC-Doctor for DOS” on page 28
– “Lenovo ThinkVantage Toolbox” on page 31
– “FRU tests” on page 31
• “Power system checkout” on page 33

The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS
diagnostics program. Some descriptions might not apply to your particular computer.

Before you go to the checkout guide, be sure to read the following important notes.

Important notes:
• Only certified trained personnel should service the computer.
• Before replacing any FRU, read the entire page on removing and replacing FRUs.
• When you replace FRUs, use new nylon-coated screws.
• Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer
that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs
might be overwritten.
• Replace a FRU only with another FRU of the correct model. When you replace a FRU, make sure that the model
of the machine and the FRU part number are correct by referring to the FRU parts list.
• A FRU should not be replaced because of a single, unreproducible failure. Single failures can occur for a
variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge,
or software errors. Consider replacing a FRU only when a problem recurs. If you suspect that a FRU is defective,
clear the error log and run the test again. If the error does not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.

What to do first
When you do return a FRU, you must include the following information in the parts exchange form or
parts return form that you attach to it:
1. Name and phone number of service technician
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Failure symptoms, error codes appearing on the display, and beep symptoms
6. Procedure index and page number in which the failing FRU was detected
7. Failing FRU name and part number
8. Machine type, model number, and serial number
9. Customer's name and address

Note: During the warranty period, the customer may be responsible for repair costs if the computer damage
was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper
maintenance by the customer. Following is a list of some common items that are not covered under warranty
and some symptoms that might indicate that the system was subjected to stress beyond normal use.

Before checking problems with the computer, determine whether the damage is covered under the warranty
by referring to the following list:

© Copyright Lenovo 2011 27

The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of an incompatible card
• Improper disc insertion or use of an optical drive
• Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive,
or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect ac power adapter on laptop products

The following symptoms might indicate damage caused by nonwarranted activities:

• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force,
or dropped.

Checkout guide
Use the following procedures as a guide in identifying and correcting problems with the ThinkPad Notebook.

Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products,
prototype cards, or modified options can lead to false indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as possible.
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test or by repeating the
operation.

Diagnostics using PC-Doctor for DOS

The ThinkPad Notebook has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can
detect errors by running the diagnostics test included in PC-Doctor.

Note: PC-Doctor for DOS is available at the following Web site:

http://www.lenovo.com/support

To create the PC-Doctor diagnostic CD, follow the instructions on the Web site.

For some possible configurations of the computer, PC-Doctor might not run correctly. To avoid this problem,
you need to initialize the computer setup by use of the ThinkPad Setup program before you run PC-Doctor.

To enter the ThinkPad Setup program, do as follows:

1. Turn on the computer.
2. When the ThinkPad logo comes up, immediately press F1 to enter the ThinkPad Setup program.

Note: If a supervisor password has been set by the customer, the ThinkPad Setup program menu appears
after the password is entered. You can start ThinkPad Setup by pressing Enter instead of entering the
supervisor password; however, you cannot change the parameters that are protected by the supervisor
password.

On the ThinkPad Setup program screen, press F9, Enter, F10, and then Enter.

28 Hardware Maintenance Manual

Note: When you initialize the computer configuration, some devices are disabled, such as the serial port. If
you test one of these devices, you will need to enable it by using Configuration utility for DOS. The utility is
available on the following Web site:
http://www.lenovo.com/support

PC-Doctor cannot be used to test a device that is in the docking station, even if the computer supports the
docking station. To test a USB device, connect it to the USB connector of the computer.

Testing the computer

In this product, you need an external optical drive to use the optical PC-Doctor diagnostic CD to test
the hardware features.

Note: The PC-Doctor for DOS CD-R/CD-RW disc supports only test of internal optical disc drives (CD-RW,
CD-RW/DVD Combo, and DVD Multi drives) on ThinkPad computers. It does not support test of any optical
disc drives connected through USB devices, PC cards, CardBus cards, or similar. The USB limitation only
applies to testing of the device. Using a bootable PC-Doctor for DOS CD/DVD, the computer can be
started from a USB attached optical drive.

To run the test, do as follows:

1. Turn off the computer.
2. Make sure that the optical drive that is supported as a startup device is installed to the computer.
3. Turn on the computer. If the computer cannot be powered on, go to “Power system checkout” on
page 33, and check the power sources.
If an error code appears, go to “Symptom-to-FRU index” on page 42.
4. When the ThinkPad logo comes up, immediately press F12 to enter the Boot Menu.
5. Insert the PC-Doctor CD into the optical drive.
6. Press cursor keys to select ATAPI CDx (x: 0, 1, ...) and then press Enter.
7. Follow the instructions on the screen.
8. The main panel of PC-Doctor appears.
9. Select Diagnostics with the arrow keys, and press Enter.

Note: You can select an item not only with the arrow keys, but also with the TrackPoint® pointer.
Instead of pressing Enter, click the left button.
A pull-down menu appears. (Its exact form depends on the model.)

Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names
may appear in the PC-Doctor menu.
Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help
Run Normal Test
Run Quick Test
CPU/Coprocessor
System Memory
Systemboard
Video Adapter
Fixed Disks
Diskette Drives
Other Devices
Communication
Wireless LAN

PC-DOCTOR 2.0 Copyright 2008 PC-Doctor, Inc. All Rights Reserved.

Use the cursor keys and ESC to move in menus. Press ENTER to select.

The options on the test menu are as follows:

Chapter 3. General checkout 29

 Diagnostics Interactive Tests
• Run Normal Test • Keyboard
• Run Quick Test • Video
• CPU/Coprocessor • Internal Speaker
• System Memory • Mouse
• Systemboard • Diskette
• Video Adapter • System Load
• Fixed Disks • Optical Drive Test
• Diskette Drives • Intel WLAN Radio Test
• Other Devices
• Communication
• Wireless LAN
Notes:
• In the Keyboard test in Interactive Tests, the Fn key should be held down for at least 2 seconds; otherwise, it
cannot be sensed.
• Video Adapter test supports only the LCD display on the ThinkPad Notebook. If you have an external monitor
attached to your computer, detach it before running PC-Doctor for DOS.
• To test Digital Signature Chip, the security chip must be set to Active.
• For models with no internal optical drives, Optical Drive Test can not be selected.

10. Run the applicable function test.

11. Follow the instructions on the screen. If there is a problem, PC-Doctor shows messages describing it.
12. To exit the test, select Quit - Exit Diag. To cancel the test, press Esc.

Note: After running PC-Doctor, check the time and date on the system and reset them if they are incorrect.

Detecting system information with PC-Doctor

PC-Doctor can detect the following system information:

Hardware Info
• System Configuration
• Memory Contents
• Physical Disk Drives
• Logical Disk Drives
• VGA Information
• IDE Drive Info
• PCI Information
• PNPISA Info
• SMBIOS Info
• VESA LCD Info
• Hardware Events Log
Utility
• Run External Tests
• Surface Scan Hard Disk
• Benchmark System
• DOS Shell
• Tech Support Form
• Battery Rundown
• View Test Log
• Print Log
• Save Log
• Full Erase Hard Drive
• Quick Erase Hard Drive

30 Hardware Maintenance Manual

Lenovo ThinkVantage Toolbox
Lenovo ThinkVantage® Toolbox is a diagnostic program that works through the Windows operating system.
It enables you to view symptoms of computer problems and solutions for them, and includes automatic
notification when action is required, computing assistance, advanced diagnostics, and diagnostic history.

Notes:
• The latest Lenovo ThinkVantage Toolbox is available at the following Web site:
http://web.lenovothinkvantagetoolbox.com/
• To install the latest Lenovo ThinkVantage Toolbox on the computer, click Download Lenovo ThinkVantage
Toolbox, and then follow the instructions on the Web site.

To run this program, do as follows:

Windows 7:
While the Windows operating system is running, press the ThinkVantage button.

To start this program, do the following:

• Click Start ➙ Control Panel ➙ System and Security ➙ Lenovo - System Health and Diagnostics.

Windows Vista and Windows XP:

Click Start ➙ All Programs ➙ ThinkVantage ➙ Lenovo ThinkVantage Toolbox

Follow the instructions on the screen. Lenovo ThinkVantageToolbox also has problem determination aids
that determine software and usage problems.

For additional information about this program, see the Help for the program.

PC-Doctor for Windows

In some models of ThinkPad Notebook, PC-Doctor for Windows enables you to troubleshoot and resolve
problems related to the computer.

Select one of the categories listed below to display symptoms and solutions:
• Check System Health
• System and Device Tests
• Lenovo Troubleshooting Center
• System Reports
• Updates and Support

PC-Doctor for Rescue and Recovery

In some models of ThinkPad Notebook, the Rescue and Recovery workspace enables you to run the
PC-Doctor program to test the hardware features of the computer.

To run the test, click “Run Diagnostics” on the Rescue and Recovery main screen.

FRU tests
The following table shows the test for each FRU.

Chapter 3. General checkout 31

Table 1. FRU tests
FRU Applicable test
System board 1. Diagnostics ➙ CPU/Coprocessor
2. Diagnostics ➙ Systemboard
3. If the docking station or the port replicator is attached to the ThinkPad computer,
detach it.
4. Place the computer on a horizontal surface, and run Diagnostics ➙ ThinkPad
Devices ➙ HDD Active Protection Test.

Note: Do not apply any physical shock to the computer while the test is running.
Power Diagnostics ➙ ThinkPad Devices ➙ ac power adapter, Battery 1 (Battery2)
LCD unit 1. Diagnostics ➙ Video Adapter
2. Interactive Tests ➙ Video
Audio Enter the ThinkPad Setup program and change Serial ATA (SATA) setting to
Compatibility, and run Diagnostics ➙ Other Device ➙ Conexant Audio.
Speaker Interactive Tests ➙ Internal Speaker
Note: Once Audio test is done, the no sound is heard this test. In this case, turn off
and turn on the computer. Then, run this test again.
Keyboard 1. Diagnostics ➙ Systemboard ➙ Keyboard
2. Interactive Tests ➙ Keyboard
Hard disk drive or solid state Enter the ThinkPad Setup program and change Serial ATA (SATA) setting to
drive Compatibility, and run Diagnostics ➙ Fixed Disks.
You can also diagnose the drive without starting up the operating system. To diagnose
the drive from the ThinkPad Setup program, do as follows:
1. Remove any diskette from the diskette drive, and then turn off the computer.
2. Turn on the computer.
3. While the message, “To interrupt normal startup, press the blue ThinkVangate
button,” is displayed at the lower left of the screen, press F1 to enter the ThinkPad
Setup program.
4. Using cursor keys, select HDD diagnostic program. Press enter.
5. Using cursor keys, select Main hard disk drive or Ultrabay hard disk drive.
6. Press Enter to start the diagnostic program.
Diskette drive 1. Diagnostics ➙ Diskette Drives
2. Interactive Tests ➙ Diskette
Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics ➙ System
Memory.
2. If the problem does not recur, return the DIMM to its place, remove the other one,
and run the test again.
TrackPoint or pointing If the TrackPoint does not work, check the configuration as specified in the ThinkPad
device Setup program. If the TrackPoint is disabled, select Automatic to enable it.

After you use the TrackPoint, the pointer may drift on the screen for a short time. This
drift can occur when a slight, steady pressure is applied to the TrackPoint pointer.
This symptom is not a hardware problem. If the pointer stops after a short time, no
service action is necessary.

If enabling theTrackPoint does not correct the problem, continue with the following:
• Interactive Tests ➙ Mouse
Touch Pad If the Touch Pad does not work, check the configuration as specified in the ThinkPad
Setup program. If the Touch Pad is disabled, select Automatic to enable it. If enabling
the Touch Pad does not correct the problem, continue with the following:
• Interactive Tests ➙ Mouse

32 Hardware Maintenance Manual

Power system checkout
To verify a symptom, do the following:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the ac power adapter.
4. Check that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the ac power adapter and install the charged battery pack.
7. Check that the battery pack supplies power when you turn on the computer.

If you suspect a power problem, see the appropriate one of the following power supply checkouts:
• “Checking the ac power adapter” on page 33
• “Checking operational charging” on page 33
• “Checking the battery pack” on page 34
• “Checking the backup battery” on page 34

Checking the ac power adapter

You are here because the computer fails only when the ac power adapter is used.
• If the power problem occurs only when the docking station or the port replicator is used, replace the
docking station or the port replicator.
• If the power-on indicator does not turn on, check the power cord of the ac power adapter for correct
continuity and installation.
• If the computer does not charge during operation, go to “Checking operational charging” on page 33.

To check the ac power adapter, do the following:

1. Unplug the ac power adapter cable from the computer.
2. Measure the output voltage at the plug of the ac power adapter cable. See the following figure:

Pin Voltage (V dc)

1 +20
3 2 0
2
3 Ground
1
(20V)

Note: Output voltage of pin no.2 of the ac power adapter may different from the one you are servicing.
3. If the voltage is not correct, replace the ac power adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem persists, go to “FRU tests” on page 31.

Note: Noise from the ac power adapter does not always indicate a defect.

Checking operational charging

To check whether the battery charges properly during operation, use a discharged battery pack or a battery
pack that has less than 50% of the total power remaining when installed in the computer.

Chapter 3. General checkout 33

Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery
pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does
not turn on, replace the battery pack.

If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is
still not charged, go to the next section.

Checking the battery pack

Battery charging does not start until the Power Manager Battery Gauge shows that less than 96% of the
total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects
the battery pack from being overcharged or from having a shortened life.

To check your battery, move your cursor to the Power Manager Battery Gauge icon in the icon tray of the
Windows taskbar and wait for a moment (but do not click), and the percentage of battery power remaining
is displayed. To get detailed information about the battery, double-click the Power Manager Battery
Gauge icon.

Note: If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and leave
it at room temperature for a while. After it cools down, reinstall and recharge it.

To check the battery pack, do the following:

1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 7 (-). See the
following figure:

Terminal Voltage (V dc)

1 + 0 to + 16.8
7 Ground (-)

7(-)
6(-)
5
3 4
2(+)
1(+)

3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.

Note: Recharging will take at least 3 hours, even if the indicator does not turn on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 5 and 7.
The resistance must be 4 to 30 K Ω. If the resistance is not correct, replace the battery pack. If the
resistance is correct, replace the system board.

Checking the backup battery

Do the following:
1. Power off the computer, and unplug the ac power adapter from it.
2. Turn the computer upside down.
3. Remove the battery pack (see “1020 Battery pack” on page 61).
4. Remove the backup battery (see “1080 Backup battery” on page 71).
5. Measure the voltage of the backup battery. See the following figure.

34 Hardware Maintenance Manual

 Wire Voltage (V dc)
Red +2.5 to +3.2
Black Ground

• If the voltage is correct, replace the system board.

• If the voltage is not correct, replace the backup battery.
• If the backup battery discharges quickly after replacement, replace the system board.

Chapter 3. General checkout 35

36 Hardware Maintenance Manual
Chapter 4. Related service information
This chapter presents following information:
• “Restoring the factory contents by using Product Recovery discs” on page 37
• “Restoring the factory contents by using Recovery Disc Set” on page 37
• “Passwords” on page 39
• “Power management” on page 40
• “Symptom-to-FRU index” on page 42

Service Web site:

When the latest maintenance diskette and the system program service diskette become available, they
will be posted on http://www.lenovo.com/support.

Restoring the factory contents by using Product Recovery discs

When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no Product
Recovery program is on the new drive. In this case, you must use the recovery discs for the computer. Order
the recovery discs and the drive at the same time so that you can recover the new drive with the pre-installed
software when they arrive. For information on which discs to order, see “Recovery discs” on page 131.

To install the factory contents by using Product Recovery discs, do the following:

Note: Recovery takes several hours. The length of time depends on the method you use. If you use recovery
discs, recovery takes at least five hours.

1. Insert the bootable Start Recovery Disc into the DVD drive.
2. Select your language and click Next.
3. Read the license. If you agree with the terms, select I accept these terms and conditions and then
click Next.
4. Insert the Operating System Recovery Disc when prompted and click Yes to begin the operating
system recovery process.
5. Insert the Product Recovery Disc when prompted and click OK.
6. If you have a Supplemental Recovery Disc, insert it when prompted and click Yes. If you do not
have a Supplemental Recovery Disc, click No.

Note: Not all recovery disc sets come with a Supplemental Recovery Disc. If there is a Supplemental
Recovery Disc, it will be clearly marked as such.
7. When all of the data has been copied from the last disc in the set, a message is displayed prompting
you to restart the computer. Remove the disc and then click Yes.

Note: The remainder of the recovery process is fully automated and no action is required by you. The
computer will restart into the Windows desktop several times and you might experience periods when
no activity is apparent on the screen for several minutes at a time. This is normal.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow
the instructions on the screen to complete the Windows setup.

Restoring the factory contents by using Recovery Disc Set

When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no product recovery
program is on the new drive. In this case, you must use the Recovery Disc Set for the computer. Order the

© Copyright Lenovo 2011 37

Recovery Disc Set and the drive at the same time so that you can recover the new drive with the pre-installed
software when they arrive. For information on which discs to order, see “Recovery discs” on page 131.

The recovery disc set consists of the user instructions and the following set of DVDs to restore the computer
to the original factory configuration.

Operating System Recovery Disc (one disc) This disc restores the Microsoft® Windows operating
system. Use this disc to start the recovery process.
Applications and Drivers Recovery Disc (one or This disc restores the preinstalled applications and
more discs) drivers on the computer.
Supplemental Recovery Disc This disc contains additional content, such as
updates to the software that was preinstalled on the
computer. Not all recovery disc sets come with a
Supplemental Recovery Disc.

Notes:
• You must have a DVD drive to use the recovery discs. If you do not have an internal DVD drive, you
can use an external USB DVD drive.
• During the recovery process, all data on the drive will be deleted. If possible, copy any important data
or personal files that you want to keep onto removable media or a network drive before you start the
recovery process.

To restore the computer to the original factory configuration using the recovery disc set, do the following:

Note: Recovery takes one to two hours to complete. The length of time depends on the method you use. If you use
recovery discs, the recovery process will take about two hours.

1. Make the CD/DVD drive the first startup device in the startup sequence using the following procedure:
a. Press and hold down the F1 key, and then turn on the computer. When the logo screen is displayed
or if you hear repeating beeps, release the F1 key. The ThinkPad Setup program opens.
b. Use the arrow keys to select Startup ➙ Boot.
c. Select the CD/DVD drive as the 1st Boot Device.
2. Insert the Operating System Recovery Disc into the DVD drive.
3. Press F10 to save the ThinkPad Setup program configuration changes. Follow the instructions on the
screen to begin the recovery process.
4. Select your language and click Next.
5. Read the license. If you agree with the terms and conditions, select I accept these terms and
conditions and then click Next. If you do not agree with the terms and conditions, follow the
instructions on the screen.
6. Click Yes in the displayed window to begin the operating system recovery process.
7. Insert the Applications and Drivers Recovery Disc when prompted and then click OK to begin the
applications and drivers recovery process.
8. If you have a Supplemental Recovery Disc, insert it when prompted and click Yes. If you do not have a
Supplemental Recovery Disc, click No.
9. When all of the data has been copied from the last disc in the set and has been processed, remove the
disc and restart the computer.

Note: The rest of the recovery process is fully automated and no action is required by you. The
computer will restart into the Microsoft Windows desktop several times and you might experience
periods when no activity is apparent on the screen for several minutes at a time. This is normal.
10. When the recovery process is complete, the Set Up Windows screen is displayed. Follow the
instructions on the screen to complete the Windows setup.

38 Hardware Maintenance Manual

11. After you have completed the Windows setup, you might want to restore the original startup sequence.
Start the ThinkPad Setup program and then press F9 to restore the default settings. Press F10 to save
and exit the ThinkPad Setup program.

Note: After restoring a drive to the factory default settings, you might need to reinstall some device drivers.

Passwords
As many as three passwords may be needed for any ThinkPad Notebook: the power-on password (POP),
the hard-disk password (HDP), and the supervisor password (SVP).

If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is
turned on. The computer does not start until the password is entered.

Note: If only an SVP is installed, the password prompt does not appear when the operating system is booted.

Power-on password
A power-on password (POP) protects the system from being powered on by an unauthorized person. The
password must be entered before an operating system can be booted. For how to remove the POP, see
“How to remove the power-on password” on page 39.

Hard-disk password
There are two hard-disk passwords (HDPs):
• User HDP - for the user
• Master HDP - for the system administrator, who can use it to get access to the hard disk even if the user
has changed the user HDP

Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires
two HDPs; the system administrator enters both in the same operation. The system administrator then
provides the user HDP to the system user.

Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be
used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized
service technicians provide any services to reset either the user or the master HDP, or to recover data from
the hard disk drive. The hard disk drive can be replaced for a scheduled fee.

For how to remove the POP, see “How to remove the hard-disk password” on page 40.

Supervisor password
A supervisor password (SVP) protects the system information stored in the ThinkPad Setup program.
The user must enter the SVP in order to get access to the ThinkPad Setup program and change the
system configuration.

Attention: If the SVP has been forgotten and cannot be made available to the service technician, there is no
service procedure to reset the password. The system board must be replaced for a scheduled fee.

How to remove the power-on password

To remove a POP that you have forgotten, do the following:

(A) If no SVP has been set:

1. Turn off the computer.

Chapter 4. Related service information 39

 2. Remove the battery pack. For how to remove the battery pack, see “1020 Battery pack” on page 61.
3. Remove the backup battery. For how to remove the backup battery, see “1080 Backup battery” on
page 71.
4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does
not appear. The POP has been removed.
5. Reinstall the backup battery and the battery pack.

(B) If an SVP has been set and is known by the service technician:
1. Turn on the computer.
2. When the ThinkPad logo comes up, immediately press F1 to enter the ThinkPad Setup program. When
the POP icon is appearing on the screen, enter the POP.
3. Select Security, using the cursor directional keys to move the menu.
4. Select Password.
5. Select Power-On Password.
6. Type the current SVP in the Enter Current Password field. then leave the Enter New Password field
blank, and press Enter twice.
7. In the Changes have been saved window, press Enter.
8. Press F10 to save changes and exit the ThinkPad Setup program.

How to remove the hard-disk password

Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made
available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any
services to reset the user HDPs or to recover data from the hard disk drive. The hard disk drive can be
replaced for a scheduled fee.

To remove a user HDP that has been forgotten, when the SVP and the master HDP are known, do the
following:
1. Turn on the computer.
2. When the ThinkPad logo comes up, immediately press F1 to enter the ThinkPad Setup program. When
the POP icon is appearing on the screen, enter the POP.
3. Select Security, using the cursor directional keys to move the menu.
4. Select Password.
5. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens.
6. Select Master HDP.
7. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password
field blank, and press Enter twice.
8. Press F10.
9. Select Yes in the Setup Configuration window. Both user HDP and master HDP will have been removed.

Power management
To reduce power consumption, the computer has three power management modes: screen blank, sleep
(standby in Windows XP), and hibernation.

Screen blank mode

If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off.

To put the computer into screen blank mode, do as follows:

40 Hardware Maintenance Manual

 1. Press Fn+F3. A panel for selecting a power plan (in Windows XP, power scheme) appears.
2. Select Power off display (keep current power plan) (in Windows XP, keep current power scheme).

You can also put the computer into screen blank mode, press ThinkVantage button and use the ThinkVantage
Productivity Center.

Note: If the computer is a Windows 7 model, it does not support ThinkVantage Productivity Center.

To end screen blank mode and resume normal operation, press any key.

Sleep (Standby) mode

When the computer enters sleep (standby) mode, the following events occur in addition to what occurs
in screen blank mode:
• The LCD is powered off.
• The hard disk drive or the solid state drive is powered off.
• The CPU stops.

To enter sleep (standby) mode, press Fn+F4.

Note: You can change the action of the Fn+F4 key combination by changing the settings in Power Manager.

In certain circumstances, the computer goes into sleep (standby) mode automatically:
• If a “suspend time” has been set on the timer, and the user does not do any operation with the keyboard,
the TrackPoint, the hard disk, the parallel connector, or the diskette drive within that time.
• If the battery indicator blinks orange, indicating that the battery power is low.

Note: Even if you do not set the low-battery alarm, the charge indicator notifies you when the battery is low,
and then the computer enters the power-saving mode automatically.

To cause the computer to return from sleep (standby) mode and resume operation, do one of the following:
• Press the Fn key.
• Open the LCD cover.
• Turn on the power switch.

Also, in either of the following events, the computer automatically returns from sleep (standby) mode and
resumes operation:
• The ring indicator (RI) is signaled by a serial device or a PC Card device.
• The time set on the resume timer elapses.

Note: The computer does not accept any input immediately after it enters sleep (standby) mode. Wait a
few seconds before taking any action to reenter operation mode.

Hibernation mode
In hibernation mode, the following occurs:
• The system status, RAM, VRAM, and setup data are stored on the hard disk.
• The system is powered off.

To cause the computer to enter hibernation mode, do any of the following:

• Press the Fn+F12 keys.

Chapter 4. Related service information 41

• If you have defined one of the following actions as the event that causes the system to go into hibernation
mode, perform that action.
– Closing the lid.
– Pressing the power button.
– Pressing Fn+F4 keys.

Also, the computer goes into hibernation mode automatically in either of the following conditions:
• If a “hibernation time” has been set on the timer, and if the user does not do any operation with the
keyboard, the TrackPoint, the hard disk drive, the parallel connector, or the diskette drive within that time.
• If the timer conditions are satisfied in suspend mode.

When the power is turned on, the computer returns from hibernation mode and resumes operation. The
hibernation file in the boot record on the hard disk drive is read, and system status is restored from the
hard disk drive.

Symptom-to-FRU index
This section contains following information:
• “Numeric error codes” on page 43
• “Error messages” on page 47
• “Beep symptoms” on page 48
• “No-beep symptoms” on page 48
• “LCD-related symptoms” on page 49
• “Intermittent problems” on page 49
• “Undetermined problems” on page 49

The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most
likely cause is listed first, in boldface type.

Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or
action, in sequence.” If replacing a FRU does not solve the problem, put the original part back in the
computer. Do not replace a nondefective FRU.

This index can also help you determine, during regular servicing, what FRUs are likely to need to be
replaced next.

A numeric error is displayed for each error detected in POST or system operation. In the displays, n can
be any number.

If no numeric code is displayed, check the narrative descriptions of symptoms. If the symptom is not
described there, go to “Intermittent problems” on page 49.

Note: For a device not supported by diagnostic codes in the ThinkPad Notebooks, see the manual for that device.

42 Hardware Maintenance Manual

Numeric error codes
Table 2. Numeric error codes
Symptom or error FRU or action, in sequence
0175 System board.
Bad CRC1, stop POST task - The EEPROM checksum is
not correct.
0176 1. Run the ThinkPad Setup program, and save the
System Security - The system has been tampered with. current setting by pressing F10.
2. System board.
0177 System board.
Bad SVP data, stop POST task - The checksum of the
supervisor password in the EEPROM is not correct.
0182 1. Run the ThinkPad Setup program. Press F9, and
Bad CRC2. Enter the ThinkPad Setup program and load Enter to load the default setting. Then save the
Setup defaults. - The checksum of the CRS2 setting in current setting by pressing F10.
the EEPROM is not correct. 2. System board.
0185 1. Run the ThinkPad Setup program. Press F9, and
Bad startup sequence settings. Enter the ThinkPad Setup Enter to load the default setting. Then save the
program and load Setup defaults. current setting by pressing F10.
0187 System board.
EAIA data access error - The access to EEPROM is failed.
0188 System board.
Invalid RFID Serialization Information Area.
0189 System board.
Invalid RFID configuration information area - The EEPROM
checksum is not correct.
0190 1. Charge the battery pack.
Critical low-battery error 2. Battery pack.
0191 1. Run the ThinkPad Setup program, and then save
System Security - Invalid Remote Change requested. current setting by pressing F10.
2. System board.
0192 System board.
System Security - Embedded Security hardware tamper
detected.
0193 Enter the supervisor password.
RF antenna has been removed
0194 Enter the supervisor password.
The computer has been carried through a security gate
0195 1. Enter the ThinkPad Setup program by entering
Security hardware tamper detected supervisor password, and select Password ➙
Security Chip ➙ Clear Security Chip to clear this
error.
2. Security chip.
3. System board.
0196 1. Enter the ThinkPad Setup program by entering
Security hardware removed supervisor password, and select Password ➙
Security Chip ➙ Clear Security Chip to clear this
error.
2. Security chip.
3. System board.

Chapter 4. Related service information 43

Table 2. Numeric error codes (continued)
Symptom or error FRU or action, in sequence
0197 The remote configuration for the security chip has
Invalid remote change requested. failed. Confirm the operation and try again.
0199 1. Run the ThinkPad Setup program, and then save
System Security - Security password retry count the current setting by pressing F10.
exceeded. 2. System board.
01C8 1. Remove either a Mini-PCI Card or a modem
Two or more modem devices are found. Remove all but daughter card. Otherwise, press Esc to ignore
one of them. Press <Esc> to continue. the warning message.
2. System board.
01C9 1. Remove either a Mini PCI Ethernet card or an
Two or more Ethernet devices are found. Remove all but Ethernet daughter card. Otherwise, press Esc to
one of them. Press <Esc> to continue. ignore the warning message.
2. System board.
01C9 1. Remove the Ethernet device that you installed; or
More than one Ethernet devices are found. Remove one press Esc to ignore the warning message.
of them. Press <Esc> to continue. 2. System board.
01CA 1. Remove the wireless LAN device that you
More than one Wireless LAN devices are found. Remove installed.
one of them. 2. System board.
0200 1. Reseat the hard disk drive.
Hard disk error - The hard disk is not working. 2. Load Setup Defaults in the ThinkPad Setup program.
3. Hard disk drive.
4. System board.
021x Run interactive tests of the keyboard and the auxiliary
Keyboard error. input device.
0220 Load Setup Defaults in the ThinkPad Setup program.
Monitor type error - Monitor type does not match the one
specified in CMOS.
0230 System board.
Shadow RAM error - Shadow RAM fails at offset nnnn.
0231 1. DIMM.
System RAM error - System RAM fails at offset nnnn. 2. System board.
0232 1. DIMM.
Extended RAM error - Extended RAM fails at offset nnnn. 2. System board.
0250 1. Charge the backup battery for more than 8 hours
System battery error - System battery is dead. by connecting the ac power adapter.
2. Replace the backup battery and run the ThinkPad
Setup program to reset the time and date.
0251 1. Charge the backup battery for more than 8 hours
System CMOS checksum bad - Default configuration by connecting the ac power adapter.
used. 2. Replace the backup battery and run the ThinkPad
Setup program to reset the time and date.
0252 Reset the password by running the ThinkPad Setup
Password checksum bad - The password is cleared. program.
0260 1. Charge the backup battery for more than 8 hours
System timer error. by connecting the ac power adapter.
2. Replace the backup battery and run the ThinkPad
Setup program to reset the time and date.
3. System board.

44 Hardware Maintenance Manual

Table 2. Numeric error codes (continued)
Symptom or error FRU or action, in sequence
0270 1. Charge the backup battery for more than 8 hours
Real-time clock error. by connecting the ac power adapter.
2. Replace the backup battery and run the ThinkPad
Setup program to reset the time and date.
3. System board.
0271 Run the ThinkPad Setup program to reset the time
Date and time error - Neither the date nor the time is set and date.
in the computer.
0280 1. Load “Setup Default” in the ThinkPad Setup
Previous boot incomplete - Default configuration used. program.
2. DIMM.
3. System board.
02B2 1. Diskette drive.
Incorrect drive A type. 2. External FDD cable.
3. I/O card.
02D0
System cache error.
02F0 1. CPU.
CPU ID:xx Failed. 2. System board.
02F4 1. Load Setup Defaults in the ThinkPad Setup
EISA CMOS not writable. program.
2. Replace the backup battery.
3. System board.
02F5 1. DIMM.
DMA test failed. 2. System board.
02F6 1. DIMM.
Software NMI failed 2. System board.
02F7 1. DIMM.
Fail-safe timer NMI failed 2. System board.
1801 Shut down the computer and remove it from the
Attached docking station is not supported docking station.
1802 1. Remove Mini PCI network card.
Unauthorized network card is plugged in - Turn off and 2. System board.
remove the miniPCI network card.
1803 1. Remove the daughter card that you installed.
Unauthorized daughter card is plugged in - Turn off and 2. System board.
remove the daughter card.
1804 1. Remove the WAN card that you installed.
Unauthorized WAN card is plugged in - Power off and 2. System board.
remove the WAN card.
1805 1. Remove the Wireless USB card that you installed.
Unauthorized Wireless USB card is plugged in - Power off 2. System board.
and remove the Wireless USB card.

Chapter 4. Related service information 45

Table 2. Numeric error codes (continued)
Symptom or error FRU or action, in sequence
1810 1. If the Access Predesktop Area has been previously
Hard disk partition layout error. disabled, then go to the ThinkPad Setup program
by pressing F1 to open the ThinkPad Setup
program. Select Security ➙ Predesktop Area
➙ Access Predesktop Area. Set this item to
Disabled. Save and exit.
2. If the Access Predesktop Area has not been
previously disabled, press Enter to load Access
Predesktop Area. Then run RECOVER TO FACTORY
CONTENTS in Access Predesktop Area.
3. If item 2 failed, press F3 in the Welcome screen in
RECOVER TO FACTORY CONTENTS. Run FDISK,
and then delete all partitions. Run RECOVER TO
FACTORY CONTENTS in Access Predesktop Area
again.
4. If item 3 failed, select CD-ROM boot in Startup in
Access Predesktop Area. Boot from the Recovery
CD and perform full recovery from it.
5. If item 4 failed, replace the hard disk drive.
1820 Remove all but the reader that you set up for the
More than one external fingerprint reader is attached. authentication.
Power off and remove all but the reader that you set up
within your main operating system.
1830 Install DIMM in Slot-0, but not in Slot-1.
Invalid memory configuration - Power off and install a Note: For the construction of the DIMM slot, see “1040
memory module to Slot-0 or the lower slot. DIMM” on page 64.
2000 1. Undock docking station or port replicator if it is
Hard Drive Active Protection sensor diagnostics attached to the ThinkPad Notebook.
failed.Press <Esc> to continue.Press <F1> to enter 2. Place the ThinkPad Notebook on a horizontal surface.
SETUP Do not apply any physical shock to the computer.
3. Run Diagnostics ➙ ThinkPad Devices ➙ HDD
Active Protection Test.
2010 Inform the following information to the customer: If in the
Warning: Your internal hard disk drive (HDD) may not primary bay the customer is using a non-Lenovo hard
function correctly on this system. Ensure that your HDD disk drive (HDD), which is not supported by this system,
is supported on this system and that the latest HDD with the risk in mind, the customer can still use it by
firmware is installed. pressing ESC. If in the primary drive bay the customer is
using a supported Lenovo HDD with an old firmware, the
customer needs to update its firmware to the latest. The
latest version is available at
http://www.lenovo.com/support
201x Inform the following information to the customer: If the
The solid state drive you have installed has not passed customer is using a non qualified SSD which is not
qualification for use in this computer. Using this drive may supported by this system, with the risk in mind, the
cause compatibility issues and potential issues with data customer can still use it by pressing ESC. Location of the
integrity, including data loss. Press <Esc> to continue. SSD is designated as below:
2010: HDD0 (in HDD slot-0)
2011: HDD1 (in HDD slot-1)
2012: Ultrabay™ with HDD adapter
2100 1. Reseat the hard disk drive.
Initialization error on HDD0 (Main hard disk drive) 2. Main hard disk drive.
3. System board.

46 Hardware Maintenance Manual

Table 2. Numeric error codes (continued)
Symptom or error FRU or action, in sequence
2102 1. Reseat the hard disk drive.
Initialization error on HDD1 (Ultrabay hard disk drive) 2. Ultrabay hard disk drive.
3. System board.
2110 1. Reseat the hard disk drive.
Read error on HDD0 (Main hard disk drive) 2. Main hard disk drive.
3. System board.
2112 1. Reseat the hard disk drive.
Read error on HDD1 (Ultrabay hard disk drive) 2. Ultrabay hard disk drive.
3. System board.

Error messages
Table 3. Error messages
Symptom or error FRU or action, in sequence
Device address conflict. 1. Load “Setup Defaults” in the ThinkPad Setup
program.
2. Backup battery.
3. System board.
Allocation error for device. 1. Load “Setup Defaults” in the ThinkPad Setup
program.
2. Backup battery.
3. System board.
Failing bits: nnnn. 1. DIMM.
2. System board.
Invalid system configuration data. 1. DIMM.
2. System board.
I/O device IRQ conflict. 1. Load “Setup Defaults” in the ThinkPad Setup
program.
2. Backup battery.
3. System board.
Hibernation error. 1. Restore the system configuration to what it was
before the computer entered hibernation mode.
2. If memory size has been changed, re-create the
hibernation file.
Fan error. 1. Fan.
2. Thermal grease.
3. System board.
Thermal sensing error. System board.
Cannot boot from any device. Check the status of device which you want to boot
from.

Device not found.

1. The device you want to boot from.
2. System board.

Device Error.
1. The device you want to boot from.
2. System board.

No valid operating system.

Chapter 4. Related service information 47

Table 3. Error messages (continued)
Symptom or error FRU or action, in sequence
1. Check that the operating system has no failure and is
installed correctly.
2. Reinstall the operation system.

Excluded from boot order.

• Enter the ThinkPad Setup program and add the device
in boot order.

Beep symptoms
Table 4. Beep symptoms
Symptom or error FRU or action, in sequence
One beep and a blank, unreadable, or flashing LCD. 1. Reseat the LCD connector.
2. LCD assembly.
3. External CRT.
4. System board.
One long and two short beeps, and a blank or unreadable 1. System board.
LCD. 2. LCD assembly.
3. DIMM.
Two short beeps with error codes. POST error. See “Numeric error codes” on page 43.
Two short beeps and a blank screen. 1. System board.
2. DIMM.
Two or more beeps, or a continuous beep. Operating If a mini-PCI Ethernet card is installed, confirm that Alert
system starts successfully. On LAN 2 in the ThinkPad Setup program is disabled.
Three short beeps, pause, three more short beeps, and 1. DIMM.
one short beep. 2. System board.
One short beep, pause, three short beeps, pause, three
more short beeps, and one short beep.
Only the cursor appears. Reinstall the operating system.
Four cycles of four short beeps and a blank screen. System board (security chip)
Five short beeps and a blank screen. System board

No-beep symptoms
Table 5. No-beep symptoms
Symptom or error FRU or action, in sequence
No beep, power-on indicator on, LCD blank, and no 1. Make sure that every connector is connected
POST. tightly and correctly.
2. DIMM.
3. System board.
No beep, power-on indicator on, and LCD blank during 1. Reseat DIMM.
POST. 2. System board.
The power-on password prompt appears. A power-on password or a supervisor password is set.
Type the password and press Enter.
The hard-disk password prompt appears. A hard-disk password is set. Type the password and
press Enter.

48 Hardware Maintenance Manual

LCD-related symptoms
Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a
small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but
excessive pixel problems can cause viewing concerns.

If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the
LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced.
Notes:
• This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later.
• Lenovo will not provide replacement if the LCD is within specification as we cannot guarantee that any
replacement LCD will have zero pixel defects.
• One pixel consists of R, G, B sub-pixels.

Table 6. LCD-related symptoms

Symptom or error FRU or action, in sequence
No beep, power-on indicator on, and a blank LCD during System board.
POST.
• LCD backlight not working. 1. Reseat the LCD connectors.
• LCD too dark. 2. LCD assembly.
• LCD brightness cannot be adjusted. 3. System board.
• LCD contrast cannot be adjusted.
• LCD screen unreadable. 1. See important note for “LCD-related symptoms.”
• Characters missing pixels. 2. Reseat all LCD connectors.
• Screen abnormal. 3. LCD assembly.
• Wrong color displayed. 4. System board.
Horizontal or vertical lines displayed on LCD. LCD assembly.

Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware
defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be
considered only when a problem recurs.

When analyzing an intermittent problem, do the following:

1. Run the diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRUs.
3. If any error is detected, replace the FRU shown by the FRU code. Rerun the test to verify that no
more errors exist.

Undetermined problems
If the diagnostic tests did not identify the adapter or device that has failed, if wrong devices are installed,
or if the system simply is not operating, follow these procedures to isolate the failing FRU (do not isolate
FRUs that have no defects).

Verify that all attached devices are supported by the computer.

Verify that the power supply being used at the time of the failure is operating correctly. (See “Power system
checkout” on page 33.)

1. Turn off the computer.

2. Visually check each FRU for damage. Replace any damaged FRU.

Chapter 4. Related service information 49

 3. Remove or disconnect all of the following devices:
a. Non-ThinkPad devices
b. Devices attached to the docking station or the port replicator
c. Printer, mouse, and other external devices
d. Battery pack
e. Hard disk drive
f. External diskette drive or optical drive
g. DIMM
h. PC Cards
4. Turn on the computer.
5. Determine whether the problem has been solved.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time (do not replace a nondefective FRU):
a. System board
b. LCD assembly

50 Hardware Maintenance Manual

Chapter 5. Status indicators
This chapter presents the system status indicators that show the status of the computer.

6 5

© Copyright Lenovo 2011 51

Table 7. Status indicators
Indicator Meaning
1 Wireless LAN status
Green: The wireless LAN feature is on, and the radio link is ready for use,
or the data is being transmitted.
Blinking Data is being transmitted (for some models).
green:

2 Wireless status
Green: Wireless PAN (Bluetooth wireless or Wireless USB) is operational.
R
This indicator is on when Wireless PAN is on and not in suspend
mode, or the data is being transmitted.
Blinking Data is being transmitted (for some models).
green:

3 Drive in use
Green: Data is being read from or written to the hard disk drive, the
diskette drive, or the drive in the Serial Ultrabay Slim device. When
this indicator is on, do not put the computer into sleep (standby)
mode or turn off the computer.

Note: Do not move the system while the green drive-in-use light is on. Sudden physical
shock could cause drive errors.
4 Fingerprint reader
Green: The fingerprint reader is ready to swipe.
status

Blinking The fingerprint is being authenticated or has been authenticated.

green:

Blinking The fingerprint could not be authenticated.

amber:

5 Battery status
Green: The battery is being charged when its charge level is between
80% and 100%. Or the battery is being discharged when its
charge level is between 0% and 80%.
Blinking green: The battery charge level is between 20% and 80%, and the
battery is being charged.
Orange: The battery charge level is between 5% and 20%, and the
battery is being discharged.
Blinking orange The battery charge level is between 5% and 20%, and the
(slow): battery is being charged.
Blinking orange The battery charge level is between 0% and 5%, and the battery
(rapid): is being charged.

6 Sleep (standby)
Green: The computer is in sleep (standby) mode.
status
Blinking The computer is entering sleep (standby) mode or hibernation mode,
green: or is resuming normal operation.

52 Hardware Maintenance Manual

Chapter 6. Fn key combinations
The following table shows the function of each combination of Fn with a function key.

Table 8. Fn key combinations

Key combination Description
Fn+F1 Reserved.
Fn+F2 Lock the computer.
Fn+F3 Select a power plan (in Windows XP, power scheme) that has been created by Power Manager,
or adjust the power level by using the slider control. When you press this combination, a
panel for selecting a power plan (power scheme) appears.

Notes:
1. To use the Fn+F3 key combination, you must have the ThinkPad PM device driver
installed on the computer.
2. If you have logged on with an administrator user ID, and you press Fn+F3, the panel for
selecting a power plan (power scheme) appears. If you have logged on with another user
ID, and you press Fn+F3, the panel does not appear.
3. You cannot turn off the computer display by pressing Fn+F3.
Fn+F4 Put the computer in sleep (standby) mode. To return to normal operation, press the Fn key
only, without pressing a function key.

Notes:
1. To use the Fn+F4 key combination, you must have the ThinkPad PM device driver
installed on the computer.
2. If you want to use the combination to put the computer into hibernation mode or
do-nothing mode (in Windows XP, shut the computer down or show the panel for turning
off the computer), change the settings in the Power Manager.
Fn+F5 Enable or disable the built-in wireless networking features and the Bluetooth features. If you
press Fn+F5, a list of wireless features is displayed. You can quickly change the power state
of each feature in the list.
Notes: If you want to use Fn+F5 to enable the wireless feature, the following device drivers
must be installed on the computer beforehand:
• ThinkPad Power Management driver
• OnScreen Display Utility
• Wireless device drivers
Fn+F6 Change the camera and audio settings.
Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director.

To disable this function and use the Fn+F7 key combination for switching a display output
location, start Presentation Director, and change the settings.

Note: If the computer is a Windows 7 model, it does not support presentation schemes, but
the Fn+F7 combination is available for switching a display output location.
For Windows 7:
Switch a display output location
• Computer display only (LCD)
• Computer display and external monitor (same image)
• Computer display and external monitor (extended desktop)
• External monitor only

© Copyright Lenovo 2011 53

Table 8. Fn key combinations (continued)
Key combination Description
Note: To switch between the computer display and an external monitor, the Win+P key
combination is also available.

For Windows Vista and Windows XP:

Switch a display output location
• External monitor
• Computer display (LCD) and external monitor
• Computer display (LCD)

Notes:
1. This function is not supported if different desktop images are displayed on the computer
display and the external monitor (the Extend desktop function).
2. This function does not work while a DVD movie or a video clip is playing.

To enable this function, start Presentation Director, and change the Fn+F7 settings.

Note: Multiple users can log on to a single operating system by using different user IDs. Each
user needs to change the settings.
Fn+F8 Change the settings of the input device.
Fn+F9 Open the ThinkPad EasyEject Utility screen. Buttons for the following choices are displayed:
• Eject ThinkPad PC from UltraBase: This button is displayed only if the ThinkPad
computer has been attached to a ThinkPad X200 UltraBase. The computer can be
detached from the ThinkPad X200 UltraBase.
• Run EasyEject Actions: This button is used to select, stop, or remove external devices
connected to the ThinkPad computer.
• Configure EasyEject Actions: Opens the ThinkPad EasyEject Utility main window.
• Fn+F9 Settings: Configures the settings for the Fn+F9 function.
Note: If the computer is a Windows 7 model, it does not support the EasyEject Utility function.
Fn+F10 Reserved.
Fn+F11 Reserved.
Fn+F12 Put the computer into hibernation mode. To return to normal operation, press the power
button for less than four seconds.
Note: To use Fn+F12 for hibernation, you must have the ThinkPad PM device driver installed
on the computer.
Fn+Home The computer display becomes brighter.
Fn+End The computer display becomes dimmer.
Fn+Spacebar Enable the FullScreen Magnifier function.
Fn+PrtSc Has the same function as the SysRq key.
Fn+ScrLk Enable or disable the numeric keypad.
Fn+Pause Has the same function as the Break key.
Fn+cursor keys These key combinations work with Windows Media Player. Fn+down arrow key works for the
Play or Pause button, Fn+up arrow key for the Stop button, Fn+right arrow key for the Next
Track button, and Fn+left arrow key for the Previous Track button.

54 Hardware Maintenance Manual

Chapter 7. FRU replacement notices
External CRU statement to customers:
Some problems with your product can be resolved with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others
are designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may
request that Lenovo installs an Optional-service CRU according to the warranty service for your product.
Where you are installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement
instructions are shipped with your product and are available from Lenovo at any time upon request. You may
find a list of CRUs in the publications that ship with your product or at http://www.lenovo.com/CRUs. You
may be required to return the defective part that is replaced by the CRU. When return is required: (1) return
instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you
may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days
of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.

This chapter presents notices related to removing and replacing parts. Read this chapter carefully before
replacing any FRU.

Screw notices
Loose screws can cause a reliability problem. In the ThinkPad Notebook, this problem is addressed with
special nylon-coated screws that have the following characteristics:

• They maintain tight connections.

• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
• Each one should be used only once.

Do the following when you service this machine:

• Keep the screw kit (for the P/N, see “Miscellaneous parts” on page 129) in your tool bag.
• Always use new screws.
• Use a torque screwdriver if you have one.

Tighten screws as follows:

• Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the plastic part:

• Logic card to plastic

Turn an additional 180 degrees after the screw head touches the surface of the logic card:

© Copyright Lenovo 2011 55

• Torque driver
If you have a torque driver, refer to the “Torque” column for each step.
• Make sure that you use the correct screw. If you have a torque screwdriver, tighten all screws firmly to the
torque shown in the table. Never use a screw that you removed. Use a new one. Make sure that all
of the screws are tightened firmly.
• Ensure torque screw drivers are calibrated correctly following country specifications.

Retaining serial numbers

This section includes the following descriptions:

• “Restoring the serial number of the system unit” on page 56

• “Retaining the UUID” on page 57
• “Reading or writing the ECA information” on page 57

Restoring the serial number of the system unit

When the computer was manufactured, the EEPROM on the system board was loaded with the serial
numbers of the system and all major components. These numbers need to remain the same throughout
the life of the computer.

If you replace the system board, you must restore the serial number of the system unit to its original value.

Before replacing the system board, save the original serial number by doing the following:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 2. Read S/N data from EEPROM.

The serial number of each device in your computer is displayed; the serial number of the system unit is
listed as follows:
• 20: Serial number

Write down that number.

Note: The serial number of the system unit is also written on the label attached to the bottom of the computer.

After you have replaced the system board, restore the serial number by doing the following:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later and restart the
computer.
2. From the main menu, select 1. Set System Identification.
3. Select 1. Add S/N data from EEPROM. Follow the instructions on the screen.

If the MTM and Product ID numbers differ from each other on the rear label, use what is shown for the
Product ID field. See example below:

56 Hardware Maintenance Manual

 MTM on rear label: TTTT-CTO S/N SSSSSSS
Product ID on rear label: TTTT-MMM (Use this number when setting Serial
Number)

In the example, the Serial Number to be input is “1STTTTMMMSSSSSSS”.

Retaining the UUID

The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at
production and stored in the EEPROM of your system board. The algorithm that generates the number is
designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same
number.

When you replace the system board, you must set the UUID on the new system board as follows:
1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already
exists, it is not overwritten.

Reading or writing the ECA information

Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board.
The electronic storage of this information simplifies the procedure to check if the ECA has been previously
applied to a machine. The machine does not need to be disassembled to check for the ECA application.

To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write
function on the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later.
1. Insert the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To read ECA information, select 2. Read ECA/rework number from EEPROM and follow the
instruction.
4. To read box build date, select 5. Read box build date from EEPROM, and follow the instruction on
the screen.

After an ECA has been applied to the machine, the EEPROM must be updated to reflect the ECA's
application. Use the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later to update the
EEPROM.

Note: Only the ECA number is stored in the EEPROM. The machine type of the ECA is assumed be the same
as the machine type of the machine that had the ECA applied to it.
1. Insert the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the
computer.
2. From the main menu, select 6. Set ECA Information.
3. To write ECA information, select 1. Write ECA/rework number from EEPROM, and follow the
instruction.
4. To write box build date, select 4. Write box build date from EEPROM, and follow the instruction on
the screen.

If the system board is being replaced, try to read the ECA information from the old system board and transfer
the information to the new system. If the system board is inoperable, this will not be possible.

Chapter 7. FRU replacement notices 57

58 Hardware Maintenance Manual
Chapter 8. Removing and replacing a FRU
External CRU statement to customers:
Some problems with your product can be resolved with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others
are designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may
request that Lenovo installs an Optional-service CRU according to the warranty service for your product.
Where you are installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement
instructions are shipped with your product and are available from Lenovo at any time upon request. You may
find a list of CRUs in the publications that ship with your product or at http://www.lenovo.com/CRUs. You
may be required to return the defective part that is replaced by the CRU. When return is required: (1) return
instructions, a prepaid shipping label, and a container will be included with the replacement CRU; and (2) you
may be charged for the replacement CRU if Lenovo does not receive the defective part within thirty (30) days
of your receipt of the replacement CRU. See your Lenovo Limited Warranty documentation for full details.

This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe
the following general rules:
1. Do not try to service any computer unless you have been trained and certified. An untrained person runs
the risk of damaging parts.
2. Before replacing any FRU, review Chapter 7 “FRU replacement notices” on page 55.
3. Begin by removing any FRUs that have to be removed before replacing the failing FRU. Any such FRUs
are listed at the top of each FRU replacement page. Remove them in the order in which they are listed.
4. Follow the correct sequence in the steps for removing a FRU, as given in the drawings by the numbers
in square callouts.
5. When turning a screw to replace a FRU, turn it in the direction as given by the arrow in the drawing.
6. When removing a FRU, move it in the direction as given by the arrow in the drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any notes that pertain to
replacement. For information about connecting and arranging internal cables, see Chapter 9 “Locations”
on page 103.
8. When replacing a FRU, use the correct screw(s) as shown in the procedures.

DANGER

Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets,
remove the battery pack, and then disconnect any interconnecting cables.

Attention: After replacing a FRU, do not turn on the computer until you have made sure that all screws,
springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking
the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.

Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before
touching it, establish personal grounding by touching a ground point with one hand or by using an
electrostatic discharge (ESD) strap (P/N 6405959).

© Copyright Lenovo 2011 59

Before servicing ThinkPad X220 Tablet and X220i Tablet models
Removing the SIM card:

Some models of the ThinkPad X220 Tablet and X220i Tablet you are servicing might have the SIM card that the
customer has been installed.

If the computer you are servicing has the SIM card, remove it before you start the servicing.

To remove the SIM card, you need to remove the battery pack first. (See “1020 Battery pack” on page 61.)

After you finish the servicing, make sure that you insert the card back into the slot firmly.

Notice on disconnecting a cable from a flip-lock ZIF connector:

Some cables used in ThinkPad X220 Tablet and X220i Tablet models are connected to flip-lock ZIF connectors.

When disconnecting a cable from a flip-lock ZIF connector, do as shown in the following figure.

1
2

60 Hardware Maintenance Manual

1010 Digitizer pen

Removal steps of digitizer pen

1020 Battery pack

Important notice for replacing a battery pack:
Lenovo ThinkVantage Toolbox (in Windows 7) has an automatic battery diagnostic that determines if the
battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic shows that
the battery is defective.

The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible
safety issue.

If Lenovo ThinkVantage Toolbox is not installed in the computer, the customer should download this program
before a non-physically damaged battery pack is replaced. Note that the replacement of a physically
damaged battery pack is not covered by the warranty.

DANGER

Use only the battery specified in the parts list for your computer. Any other battery could ignite
or explode.

Removal steps of battery pack

Slide the left battery latch to the unlocked position 1 , and then hold the right battery latch to the unlocked
position until you remove the battery 2 .

Chapter 8. Removing and replacing a FRU 61

 1

When installing:

Install the battery pack along the slide rails of the slot. Make sure that the left battery release lever is
in the locked position.

1030 Hard disk drive (HDD) and solid state drive (SSD)
• “1020 Battery pack” on page 61

Attention:
• Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to
physical shock. Improper handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the system is operating or is in suspend mode.

Removal steps of hard disk drive and solid state drive

Note: Loosen the screw 1 .

62 Hardware Maintenance Manual

 3
1

Step Screw (quantity) Color Torque

1 Hard disk drive screw, M3 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm
(1.85 kgfcm)

Chapter 8. Removing and replacing a FRU 63

 5

HDD and HDD rubber rails:

6

SSD and SSD spacers:

When installing:

Rubber rails on the hard disk drive or spacers on the solid state drive must be attached to the replacement
drive. Otherwise the drive cannot be installed properly.

1040 DIMM
For access, remove this FRU:
• “1020 Battery pack” on page 61

64 Hardware Maintenance Manual

Removal steps of DIMM
Remove the DIMM slot cover as shown in the following figure.

Note: Loosen the screws 1 .

Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0
a , but not in SLOT-1 b .

b a

When installing:

Chapter 8. Removing and replacing a FRU 65

Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into
place. Make sure that it is firmly installed in the slot and does not move easily.

1050 Hinge caps

For access, remove this FRU:
• “1020 Battery pack” on page 61

Removal steps of hinge caps

Open the LCD unit, and then remove the hinge cap.

1060 Keyboard
For access, remove this FRU:
• “1020 Battery pack” on page 61

66 Hardware Maintenance Manual

Removal steps of keyboard
Remove the screws 1 .

Step Icon Screw (quantity) Color Torque

1 M2 × 6 mm, wafer-head, nylon-coated (2) Black 0.181 Nm
(1.85 kgfcm)

Slightly press the keyboard and slide it a little bit forward, in the direction shown by arrow 2 , to detach the
front edge of the keyboard from the frame. Then, lift up the keyboard in the direction shown by arrow 3 .

Lift the keyboard a little in the direction shown by arrow 5 , and then detach the connector 4 .

Chapter 8. Removing and replacing a FRU 67

When installing:

1. Attach the keyboard connector firmly.

2. Make sure that the keyboard edge is under the frame as shown in the following figure. Then press
the keys to latch the keyboard firmly in place.

3. Gently press the keys with your palms and slightly slide the keyboard toward you until it snaps into
position.

68 Hardware Maintenance Manual

4. Secure the keyboard by tightening the screws from the bottom side of the computer.

1070 Palm rest

For access, remove these FRUs in order:
• “1020 Battery pack” on page 61
• “1060 Keyboard” on page 66

Removal steps of palm rest

Step Icon Screw (quantity) Color Torque

1 M2 × 6 mm, wafer-head, nylon-coated (5) Black 0.181 Nm
(1.85 kgfcm)

Chapter 8. Removing and replacing a FRU 69

 2

5 4

When installing:

When you attach the palm rest, do as follows:

1. Attach the touch pad connector firmly to the system board.
2. Press the left and right top edges of the palm rest to fit it into place.
3. Push the front side of the palm rest until it clicks into place.
4. Close the LCD cover and turn the computer over. And then fasten the five screws to secure the palm rest.

70 Hardware Maintenance Manual

1080 Backup battery

DANGER

Use only the battery specified in the parts list for your computer. Any other battery could ignite
or explode.

For access, remove these FRUs in order:

• “1020 Battery pack” on page 61
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69

Chapter 8. Removing and replacing a FRU 71

Removal steps of backup battery

72 Hardware Maintenance Manual

When installing:

Make sure that the battery connector is attached firmly.

1090 PCI Express Mini Card for wireless LAN/WiMAX

For access, remove these FRUs in order:
• “1020 Battery pack” on page 61
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69

Removal steps of PCI Express Mini Card for wireless LAN/WiMAX

In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the
connectors with your fingers and gently unplug them in the direction shown by the arrow.

Note: Some models might have three antenna cables.

Chapter 8. Removing and replacing a FRU 73

 Step Screw (quantity) Color Torque
2 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm
(1.85 kgfcm)

When installing
• In models with a wireless LAN card that has two antenna connectors, plug the gray cable into the jack
labeled MAIN or M on the card, and the black cable into the jack labeled AUX or A. If the computer you
are servicing has three cables, put the white cable in the cable protection tube.

74 Hardware Maintenance Manual

• In models with a wireless LAN card that has three antenna connectors, plug the gray cable (MAIN) into
the jack labeled TR1, the white cable (third) into the jack labeled RO or TR3, and the black cable (AUX)
into the jack labeled TR2 on the card.

1100 PCI Express Mini Card for wireless WAN

For access, remove these FRUs in order:
• “1020 Battery pack” on page 61
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69

Removal steps of PCI Express Mini Card for wireless WAN

In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the
connectors with your fingers and gently unplug them in the direction of the arrow.

Step Screw (quantity) Color Torque

2 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm
(1.85 kgfcm)

Chapter 8. Removing and replacing a FRU 75

When installing:

When you install the card, plug the red cable into the jack labeled MAIN on the card, and the blue cable into
the jack labeled AUX.

If the computer you are servicing is the wireless WAN-ready model, put the antenna cables in the cable
protection tube and place them as shown in the following figure.

1110 Bluetooth daughter card

For access, remove these FRUs in order:
• “1020 Battery pack” on page 61
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69

76 Hardware Maintenance Manual

Removal steps of Bluetooth daughter card

Step Screw (quantity) Color Torque

1 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm
(1.85 kgfcm)

When installing:

Make sure that the connector 2 is attached firmly.

1120 Keyboard bezel

For access, remove these FRUs in order:
• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69

Chapter 8. Removing and replacing a FRU 77

Removal steps of keyboard bezel
1

2
2

1
1

Step Screw (quantity) Color Torque

1 M2 × 6 mm, wafer-head, nylon-coated (3) Black 0.181 Nm
(1.85 kgfcm)
2 M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm
(1.85 kgfcm)

3
3
3

Step Screw (quantity) Color Torque

3 M2 × 2 mm, wafer-head, nylon-coated (4) Black 0.181 Nm
(1.85 kgfcm)

Rotate the LCD unit as shown in the following figure.

78 Hardware Maintenance Manual

 4

In step 5 , detach the claws. Then remove the keyboard bezel in the direction shown by arrow 6 .

Attention: When you service the keyboard bezel, avoid any kind of rough handling.

5
5

6
5
5

When installing:

Make sure that all the claws are attached firmly.

1130 LCD assembly

For access, remove these FRUs in order:
• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1050 Hinge caps” on page 66
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69
• “1090 PCI Express Mini Card for wireless LAN/WiMAX” on page 73

Chapter 8. Removing and replacing a FRU 79

• “1100 PCI Express Mini Card for wireless WAN” on page 75
• “1120 Keyboard bezel” on page 77

Removal steps of LCD assembly

Step Screw (quantity) Color Torque

1 M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm
(4 kgfcm)

Step Screw (quantity) Color Torque

2 M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm
(4 kgfcm)

Before step 3 , strip off the tapes securing the antenna cables, and release the cables from the cable
guides of the frame.

80 Hardware Maintenance Manual

 3

When installing:
• Make sure that you attach the connectors firmly.

Chapter 8. Removing and replacing a FRU 81

• Make sure that you route the cables correctly and you tape up the cables in the proper positions as
shown in the following figure.
• When you route the cables, make sure that they are not subjected to any tension. Tension could cause
the cables to be damaged by the cable guides, or a wire to be broken.

1140 DC-in connector, base cover, fan, digitizer pen case, and pen
switch assembly
For access, remove these FRUs in order:
• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1050 Hinge caps” on page 66
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69
• “1090 PCI Express Mini Card for wireless LAN/WiMAX” on page 73
• “1100 PCI Express Mini Card for wireless WAN” on page 75
• “1110 Bluetooth daughter card” on page 76
• “1120 Keyboard bezel” on page 77
• “1130 LCD assembly” on page 79

Removal steps of DC-in connector, base cover, fan, digitizer pen case, and pen switch assembly
Remove the top shielding assembly at first.

82 Hardware Maintenance Manual

 2

Step Screw (quantity) Color Torque

1 M1.6 x 3 + 4.2A mm, shoulder socket-head, nylon-coated (1) Black 0.181 Nm
(1.85 kgfcm)
2 M2 x 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm
(1.85 kgfcm)

4 4
4

Chapter 8. Removing and replacing a FRU 83

 Step Screw (quantity) Color Torque
4 M2 × 3.5 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm
(1.85 kgfcm)

When installing:

Make sure that the wireless switch is adjusted as shown by callout a .

Turn the system board over, and then disconnect the DC-in connector, the fan connector, and the pen
switch connector from the system board.

9
8

10

84 Hardware Maintenance Manual

 11

Disconnect the fan assembly from the system board.

12
15
16
13
14

Step Screw (quantity) Color Torque

11 M2 × 3.5 mm, flat-head, nylon-coated (1) Silver 0.181 Nm
(1.85 kgfcm)

When installing:
• Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams,
on the part marked a as in the following figure. Either too much or too less application of grease can
cause a thermal problem due to imperfect contact with a component. You need to peel the thin film
off from the rubber b .
• Make sure that the DC-in connector, the fan connector, and the pen switch connector are attached to
the system board firmly.

Chapter 8. Removing and replacing a FRU 85

 b

Applying labels to the base cover:

The new base cover FRU is shipped with a kit containing labels of several kinds.

Note: If the Windows Authentication label (COA) 2 is attached to a part that is replaced, return the old part
with the label attached to the customer, or provide a letter to the customer stating what the label was
originally on the system and what the label part number, serial number, and product key were.

When you replace the base cover, you need to apply the following labels:

19 Homologation label
20 Product label

The following labels need to be peeled off from the old base cover, and need to be put on the new base cover.

1 China telecom label

2 Windows Certificate of Authentication label (COA)
3 SIM label
4 BTY word label
5 Asset tag
6 IMEI label
7 Brazil WWAN label
8 Wireless card label (only for Brazil)
9 Modem AMOM label
10 MEDEM label (only for PRC model)
11 Bluetooth label
12 China WWAN label
13 SIRIM label or POSTEL label
14 Non-encryption label (for non-TPM model) or Rating label (only for Indonesia)
15 AT Wireless LAN MAC address label
16 Vodafone label
17 FCC label
18 Serial number label
21 FCC-ID label for contactless smart card model

86 Hardware Maintenance Manual

 22 Israel label (67.8 mm x 27.9 mm)
23 Israel label (72.2 mm x 29.7 mm)
24 Israel label (76.2 mm x 31.8 mm)
25 Ethernet label or Onboard LAN MAV address label

For some models, you need to apply two FCC labels, 17 and 21 . Check the old base cover; if it has
two FCC labels, apply both to the new base cover.

For the location of each label, refer the following figure:

1 2 3 4

5
25
6
21
7
20 8
9 13
19 10
11
18
12
17
24
23 14
22

16 15

1150 System board and ExpressCard slot assemblies

Important notices for handling the system board:

When handling the system board, bear the following in mind.

• The system board has an accelerometer, which can be broken if several thousands of G-forces are applied.

Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench
can subject the accelerometer to as much as 6,000 G's of shock.
• Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or
composite.
• If a system board is dropped, you must test it, using PC-Doctor for DOS, to make sure that the HDD
Active Protection System™ still functions.

Note: If the test shows that the HDD Active Protection System is not functioning, be sure to document the
drop in a reject report, and replace the system board.
• Avoid rough handling of any kind.
• At every point in the process, be sure not to drop or stack the system board.
• If you put a system board down, be sure to put it only on a padded surface such as an ESD mat or a
corrugated conductive surface.

Chapter 8. Removing and replacing a FRU 87

After replacing the system board, run PC-Doctor for DOS to make sure that the HDD Active Protection
System still functions. The procedure is as follows:
1. Place the computer on a horizontal surface.
2. Run Diagnostics ➙ ThinkPad Devices ➙ HDD Active Protection Test.

Attention: Do not apply physical shock to the computer while the test is running.

For access, remove these FRUs in order:

• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1050 Hinge caps” on page 66
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69
• “1090 PCI Express Mini Card for wireless LAN/WiMAX” on page 73
• “1100 PCI Express Mini Card for wireless WAN” on page 75
• “1110 Bluetooth daughter card” on page 76
• “1120 Keyboard bezel” on page 77
• “1130 LCD assembly” on page 79
• “1140 DC-in connector, base cover, fan, digitizer pen case, and pen switch assembly” on page 82

Removal steps of system board and ExpressCard slot assembly

The following components soldered on the system board are extremely sensitive. When you service the
system board, avoid any kind of rough handling.

a Platform Controller Hub (PCH)

b CPU
c Accelerometer chip for the HDD Active Protection System

c
b

Note: The ExpressCard slot assembly is attached to the system board.

88 Hardware Maintenance Manual

 Step Screw (quantity) Color Torque
1 M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm
(1.85 kgfcm)

Turn the system board over, and then remove the ExpressCard slot assembly from the system board.

2
3

1160 Speaker assembly

For access, remove these FRUs in order:
• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1050 Hinge caps” on page 66
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69
• “1090 PCI Express Mini Card for wireless LAN/WiMAX” on page 73
• “1100 PCI Express Mini Card for wireless WAN” on page 75
• “1110 Bluetooth daughter card” on page 76
• “1120 Keyboard bezel” on page 77
• “1130 LCD assembly” on page 79
• “1140 DC-in connector, base cover, fan, digitizer pen case, and pen switch assembly” on page 82

Chapter 8. Removing and replacing a FRU 89

Removal steps of speaker assembly
Remove the speaker assembly from the base cover assembly.

Step Screw (quantity) Color Torque

2 M2 × 3mm, wafer-head, nylon-coated (1) Black 0.181 Nm
(1.85 kgfcm)

When installing:

Route the speaker cables along the cable guides as shown in the following figure.

1170 mSATA solid state drive

For access, remove these FRUs in order:
• “1020 Battery pack” on page 61
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69

Attention:
• Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to
physical shock. Improper handling can cause damage and permanent loss of data.
• Before removing the drive, have the user make a backup copy of all the information on it if possible.
• Never remove the drive while the system is operating or is in suspend mode.

90 Hardware Maintenance Manual

Removal steps of mSATA solid state drive

Step Screw (quantity) Color Torque

1 M2 × 3 mm, flat-head, nylon-coated (1) Black 0.181 Nm
(1.85 kgfcm)

2010 LCD front bezel

For access, remove this FRU:
• “1020 Battery pack” on page 61

Chapter 8. Removing and replacing a FRU 91

Removal steps of LCD front bezel

Step Screw cap Screw (quantity) Color Torque

1 M2.5 × 8 mm, wafer-head, nylon-coated (3) Black 0.392 Nm
(4 kgfcm)

When installing:

Attach the fingerprint reader connector firmly.

92 Hardware Maintenance Manual

2020 Micro-Processor card
For access, remove these FRUs in order:
• “1020 Battery pack” on page 61
• “2010 LCD front bezel” on page 91

Removal steps of Micro-Processor card

Step Screw (quantity) Color Torque

1 M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm
(1.85 kgfcm)

Chapter 8. Removing and replacing a FRU 93

When installing:

Make sure that connectors 2 and 3 are attached firmly.

2030 Hinge
For access, remove these FRUs in order:
• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1050 Hinge caps” on page 66
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69
• “1090 PCI Express Mini Card for wireless LAN/WiMAX” on page 73
• “1100 PCI Express Mini Card for wireless WAN” on page 75
• “1120 Keyboard bezel” on page 77
• “1130 LCD assembly” on page 79
• “2010 LCD front bezel” on page 91
• “2020 Micro-Processor card” on page 93

94 Hardware Maintenance Manual

Removal steps of the hinge
1

Step Screw (quantity) Color Torque

1 M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm
(4 kgfcm)

Detach the hinge from the LCD rear cover, and gently pull the cables out through the guide hole in the hinge.
Pull them all at once. As you pull them, be sure not to subject them to any tension, which could cause them
to be damaged by the cable guides, or a wire to be broken.

2040 LCD panel and LCD cable

For access, remove these FRUs in order:
• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1050 Hinge caps” on page 66
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69
• “1090 PCI Express Mini Card for wireless LAN/WiMAX” on page 73
• “1100 PCI Express Mini Card for wireless WAN” on page 75
• “1120 Keyboard bezel” on page 77
• “1130 LCD assembly” on page 79
• “2010 LCD front bezel” on page 91
• “2020 Micro-Processor card” on page 93

Chapter 8. Removing and replacing a FRU 95

• “2030 Hinge” on page 94

Removal steps of LCD panel and LCD cable

1
1
1
2
2

2
1

Step Screw cap Screw (quantity) Color Torque

1 M2.5 × 8 mm, wafer-head, nylon-coated (6) Black 0.392 Nm
(4 kgfcm)
2 — M2 × 3.5 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm
(1.85 kgfcm)

In step 3 , detach the claws. Then remove the LCD panel.

3 3
3
3
3
3

3
3

96 Hardware Maintenance Manual

When installing:

• Make sure that all the claws are attached firmly.

• When attaching the LCD panel to the cover, gently press the left and right edges covered with metal. Do
not press the surface of the panel or apply any excessive force to the panel.

Turn the LCD panel over, and then remove the LCD cable from the LCD panel.

10

11

Chapter 8. Removing and replacing a FRU 97

 3

When installing:

• Route the cable through the hooks and make sure the white dot 1 on the cable is aligned with the hooks.
Then paste a film on top of the hooks to secure the cable.
• Keep the cable between callout 1 and 2 short to prevent the cable from being winded.
• Route all the cables on the far side of the rib 3 so they are not pinched. No cables are pinched under
the hinge.

2050 Integrated camera

For access, remove these FRUs in order:
• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1050 Hinge caps” on page 66
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69
• “1090 PCI Express Mini Card for wireless LAN/WiMAX” on page 73
• “1100 PCI Express Mini Card for wireless WAN” on page 75
• “1120 Keyboard bezel” on page 77
• “1130 LCD assembly” on page 79
• “2010 LCD front bezel” on page 91
• “2020 Micro-Processor card” on page 93
• “2030 Hinge” on page 94
• “2040 LCD panel and LCD cable” on page 95

98 Hardware Maintenance Manual

Removal steps of Integrated camera

1
2

Step Screw (quantity) Color Torque

1 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm
(1.85 kgfcm)

2060 LCD rear cover and wireless antenna cables

For access, remove these FRUs in order:
• “1010 Digitizer pen” on page 61
• “1020 Battery pack” on page 61
• “1050 Hinge caps” on page 66
• “1060 Keyboard” on page 66
• “1070 Palm rest” on page 69
• “1090 PCI Express Mini Card for wireless LAN/WiMAX” on page 73
• “1100 PCI Express Mini Card for wireless WAN” on page 75
• “1120 Keyboard bezel” on page 77
• “1130 LCD assembly” on page 79
• “2010 LCD front bezel” on page 91
• “2020 Micro-Processor card” on page 93
• “2030 Hinge” on page 94
• “2040 LCD panel and LCD cable” on page 95
• “2050 Integrated camera” on page 98

Chapter 8. Removing and replacing a FRU 99

Removal steps of LCD rear cover and wireless antenna cables

Step Screw (quantity) Color Torque

1 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm
(1.85 kgfcm)

In step 3 , release the antenna cables from the cable guides of the rear cover.

100 Hardware Maintenance Manual

 3

3 4

When installing:

Place the antenna assembly as shown in the following figure.

a Wireless WAN antenna, AUX (blue)

b Wireless LAN antenna, AUX (black)
c Wireless LAN antenna, MAIN (gray)
d Wireless WAN antenna, MAIN (red)

a b c d

Attention: As you route the antenna cables, make sure that they are not subjected to any tension. Tension
could cause the cables to be damaged by the cable guides, or a wire to be broken.

Chapter 8. Removing and replacing a FRU 101

102 Hardware Maintenance Manual
Chapter 9. Locations
This chapter presents the locations of ThinkPad X220 Tablet and X220i Tablet features and hardware
components.

Front view
1 Integrated camera
2 Built-in microphone
3 Security keyhole
4 Tablet digitizer pen
5 Hard disk drive (HDD) or solid state drive (SSD)
6 Combo audio jack
7 Ethernet connector
8 Always On USB connector
9 Media card reader slot
10 TrackPoint pointing stick
11 TrackPoint buttons
12 Touch pad
13 UltraNav®
14 Volume control buttons
15 ThinkVantage button
16 Power switch

© Copyright Lenovo 2011 103

Rear view
1 Status indicators
Note: For the description of each indicator, see Chapter 5 “Status indicators” on page 51.
2 ExpressCard slot
3 Wireless radio switch
4 USB connector
5 DisplayPort connector
6 External monitor connector
7 USB connector
8 ac power connector

2
3
8 4
5
6
7

104 Hardware Maintenance Manual

Rear view (tablet mode)
1 Tablet buttons
2 Fingerprint reader
3 Status indicators

Note: For the description of each indicator, see Chapter 5 “Status indicators” on page 51.

Bottom view
1 Battery pack latch
2 Battery pack
3 Docking connector
4 DIMM slots
5 Built-in speakers

1
2
3

Chapter 9. Locations 105

Top view (ThinkPad X220 UltraBase)
1 Docking connector
2 ac power connector
3 Ethernet connector
4 DisplayPort connector
5 External monitor connector
6 Headphone jack
7 Microphone jack
8 USB connectors
9 Security keyhole
10 Security lock key
11 Serial Ultrabay Slim device

2
3
4

5
11
6
10 7
8
9

Bottom view (ThinkPad X220 UltraBase)

1 UltraBase eject request button
2 Docking indicator
3 UltraBase eject lever
4 Holes for speakers

4 1
2
3

106 Hardware Maintenance Manual

Chapter 10. Parts list
This section contains following lists of the service parts.
• “Overall” on page 108
• “LCD FRUs” on page 124
• “Keyboard” on page 128
• “Miscellaneous parts” on page 129
• “ac power adapter ” on page 130
• “Power cords” on page 130
• “Recovery discs” on page 131
• “Common service tools” on page 138

Notes:
• Each FRU is available for all types or models, unless specific types or models are specified.
• FRU with specific models listed and described as xxU (where U is an example of a country designator) should be
used for all models ending in U.
• FRU with specific models listed and described as 3Dx (where 3D is an example of a unique configuration) should be
used for all of these models, unless specific country or region designator is specified.
• A CRU (customer replaceable unit) is identified by a single asterisk (*) or two asterisks (**) in the CRU ID column. An
N in the CRU ID column means that the part is not a CRU. A single asterisk (*) means that the part is a Self-service
CRU; two asterisks (**) means that the part is an Optional-service CRU.
External CRU statement to customers:
Some problems with your product can be resolved with a replacement part you can install yourself, called
a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as Self-service CRUs and others are
designated as Optional-service CRUs. Installation of Self-service CRUs is your responsibility; you may request
that Lenovo installs an Optional-service CRU according to the warranty service for your product. Where you are
installing the CRU, Lenovo will ship the CRU to you. CRU information and replacement instructions are shipped
with your product and are available from Lenovo at any time upon request. You may find a list of CRUs in the
publications that ship with your product or at http://www.lenovo.com/CRUs. You may be required to return the
defective part that is replaced by the CRU. When return is required: (1) return instructions, a prepaid shipping label,
and a container will be included with the replacement CRU; and (2) you may be charged for the replacement CRU if
Lenovo does not receive the defective part within thirty (30) days of your receipt of the replacement CRU. See your
Lenovo Limited Warranty documentation for full details.
ThinkPad computers contain the following types of CRUs:
– Self-service CRUs: These CRUs unplug or are held by no more than two screws. Examples of these types
of CRUs include the ac power adapter, power cord, battery, and hard disk drive. Other Self-service CRUs
depending on product design may include the memory module, wireless card, keyboard, and palm rest with
finger print reader and touchpad.
– Optional-service CRUs: These CRUs are isolated parts within the computer that are concealed by an access
panel that is typically secured by more than two screws. Once the access panel is removed, the specific
CRU is visible.

© Copyright Lenovo 2011 107

• FRUs marked with OP are available as options.

Overall
1

26

25

24

23

22
3

4
21
5

20 6
7

19
8

18 10

17 11

12

13

14

16
15

108 Hardware Maintenance Manual

Table 9. Parts list - Overall
No. FRU FRU no. CRU
ID
1 LCD unit (see “LCD FRUs” on page 124.)
2 Digitizer pen case assembly 04W1477 N
3 Backup battery 02K7078 N
4 1-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card 55Y3715 **
• 4294-CTO
• 4296-CTO, 2Rx
• 4297-CTO
• 4298-CTO, 38x, 3Mx, 3Nx
• 4299-CTO
• 4300-CTO
• 4301-CTO
4 2-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card 55Y3716 **
• 4294-CTO, 2Ux, 2Tx, 2Gx, 2Fx, 2Cx, 2Bx, 25x
• 4296-CTO, 3Jx, 3Cx, 2Ax, 3Sx, 3Gx, 2Qx, 2Cx
• 4297-CTO, 23x, 24x
• 4298-CTO, 4Jx, 4Hx, 37x, 2Xx, 2Rx, 27x
• 4299-CTO, 3Ex, 3Dx, 3Cx, 3Bx, 2Kx, 28x, 27x, 2Mx
• 4300-CTO
• 4301-CTO
4 4-GB DDR3-1333 SDRAM SO-DIMM (PC3-10600) card 55Y3717 **
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Kx, 24x, 2Ex, 2Dx, 27x, 26x, 28x
• 4296-CTO, 3Mx, 3Lx, 3Ex, 3Dx, 3Bx, 3Ax, 39x, 37x, 36x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx,
2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Bx, 29x, 28x, 27x, 26x, 22x, 3Rx, 3Qx, 3Px, 3Nx, 3Kx,
3Hx, 3Fx, 2Tx, 2Sx, 2Jx, 2Hx, 2Gx, 2Fx, 25x, 24x, 23x
• 4297-CTO, 22x
• 4298-CTO, 53x, 52x, 4Yx, 4Xx, 4Vx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Lx, 4Kx, 4Gx,
4Dx, 4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx, 3Vx, 3Ux,
3Tx, 3Sx, 3Rx, 3Qx, 3Px, 3Lx, 3Kx, 3Jx, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x,
35x, 2Wx, 2Vx, 2Tx, 2Sx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Ex, 2Dx, 2Cx,
2Bx, 2Ax, 29x, 28x, 4Zx, 4Wx, 4Fx, 4Ex, 36x, 34x, 33x, 32x, 2Zx, 2Yx, 26x
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ax, 39x, 37x,
36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Rx, 2Qx, 2Px, 2Lx, 2Jx,
2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Nx, 2Cx, 2Bx, 2Ax, 29x, 26x
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel® Core™ i5-2520M processor, AMT, TPM, AES 04W2127 N
• 4294-CTO, 2Nx, 23x, 24x
• 4296-CTO, 3Jx, 3Cx, 3Bx, 36x, 33x, 32x, 2Xx, 2Wx, 2Mx, 2Lx, 2Kx, 2Bx, 22x
• 4297-CTO, 24x, 23x
• 4298-CTO, 4Yx, 4Vx, 4Hx, 4Gx, 4Cx, 4Bx, 42x, 3Zx, 3Wx, 3Vx, 3Sx, 3Rx, 3Qx, 3Px, 3Mx,
3Jx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 2Zx, 2Xx, 2Vx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx,
2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Dx, 2Ax, 28x, 27x
• 4299-CTO, 53x, 4Xx, 4Vx, 4Ux, 4Cx, 4Bx, 36x, 35x, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Qx,
2Px, 2Kx, 2Jx, 2Hx, 2Fx, 2Ax, 28x, 27x
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 109

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
5 System board assembly with Intel Core i5-2520M processor, AMT, non-TPM, non-AES 04W2131 N
• 4294-CTO, 2Ax
• 4296-CTO, 3Dx
• 4297-CTO
• 4298-CTO, 4Ax, 49x
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M processor, non-AMT, TPM, AES 04W2129 N
• 4294-CTO, 2Rx, 2Kx
• 4296-CTO, 26x, 27x
• 4297-CTO
• 4298-CTO, 4Xx, 4Jx, 46x, 45x
• 4299-CTO, 3Bx
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M processor, non-AMT, non-TPM, non-AES 04W2133 N
• 4294-CTO, 29x, 28x
• 4296-CTO, 3Ax, 28x
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M processor, AMT, TPM, AES 04W2128 N
• 4294-CTO, 22x
• 4296-CTO, 3Ex, 39x, 38x, 37x, 35x, 34x, 2Zx, 2Yx, 2Ux, 2Px, 2Nx, 2Ex, 2Dx
• 4297-CTO
• 4298-CTO, 4Ux, 4Dx, 48x, 47x, 44x, 43x, 3Yx, 3Xx, 3Ux, 3Tx, 3Lx, 3Kx, 3Hx, 3Gx, 3Fx,
35x, 32x, 2Yx, 2Wx, 2Ux, 2Tx, 2Fx, 2Ex, 2Cx, 2Bx, 29x, 26x
• 4299-CTO, 54x, 4Yx, 3Ex, 3Dx, 3Cx, 3Ax, 39x, 38x, 37x, 34x, 33x, 32x, 2Zx, 2Sx, 2Rx,
2Lx, 2Gx, 2Ex, 2Dx, 2Bx, 29x, 26x
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M processor, AMT, non-TPM, non-AES 04W2132 N
• 4294-CTO, 2Ax
• 4296-CTO, 3Dx
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M processor, non-AMT, TPM, AES 04W2130 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

110 Hardware Maintenance Manual

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
5 System board assembly with Intel Core i7-2620M processor, non-AMT, non-TPM, non-AES 04W2134 N
• 4294-CTO
• 4296-CTO, 29x
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i3-2310M processor, non-AMT, TPM, non-AES 04W2136 N
• 4294-CTO, 2Ex, 2Dx, 27x, 26x, 25x
• 4296-CTO, 2Jx, 2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x, 23x
• 4297-CTO
• 4298-CTO, 4Fx, 4Ex, 3Nx
• 4299-CTO, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i3-2310M processor, non-AMT, non-TPM, non-AES 04W2135 N
• 4294-CTO, 2Cx, 2Bx
• 4296-CTO, 2Tx, 2Sx, 2Rx, 2Qx
• 4297-CTO, 22x
• 4298-CTO, 36x
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M processor, AMT, TPM, AES 04W1534 N
• 4294-CTO, 2Nx, 23x, 24x
• 4296-CTO, 3Jx, 3Cx, 3Bx, 36x, 33x, 32x, 2Xx, 2Wx, 2Mx, 2Lx, 2Kx, 2Bx, 22x
• 4297-CTO, 24x, 23x
• 4298-CTO, 4Yx, 4Vx, 4Hx, 4Gx, 4Cx, 4Bx, 42x, 3Zx, 3Wx, 3Vx, 3Sx, 3Rx, 3Qx, 3Px, 3Mx,
3Jx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 2Zx, 2Xx, 2Vx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx,
2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Dx, 2Ax, 28x, 27x
• 4299-CTO, 53x, 4Xx, 4Vx, 4Ux, 4Cx, 4Bx, 36x, 35x, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Qx,
2Px, 2Kx, 2Jx, 2Hx, 2Fx, 2Ax, 28x, 27x
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M AMT, non-TPM, non-AES 04W1535 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO, 4Ax, 49x
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M, non-AMT, non-TPM, AES 04W1536 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 111

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
5 System board assembly with Intel Core i5-2520M, non-AMT, non-TPM, non-AES 04W1537 N
• 4294-CTO, 29x, 28x
• 4296-CTO, 3Ax, 28x
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M, AMT, TPM, AES 04W1538 N
• 4294-CTO, 22x
• 4296-CTO, 3Ex, 39x, 38x, 37x, 35x, 34x, 2Zx, 2Yx, 2Ux, 2Px, 2Nx, 2Ex, 2Dx
• 4297-CTO
• 4298-CTO, 4Ux, 4Dx, 48x, 47x, 44x, 43x, 3Yx, 3Xx, 3Ux, 3Tx, 3Lx, 3Kx, 3Hx, 3Gx, 3Fx,
35x, 32x, 2Yx, 2Wx, 2Ux, 2Tx, 2Fx, 2Ex, 2Cx, 2Bx, 29x, 26x
• 4299-CTO, 54x, 4Yx, 3Ex, 3Dx, 3Cx, 3Ax, 39x, 38x, 37x, 34x, 33x, 32x, 2Zx, 2Sx, 2Rx,
2Lx, 2Gx, 2Ex, 2Dx, 2Bx, 29x, 26x
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M, AMT, non-TPM, non-AES 04W1539 N
• 4294-CTO, 2Ax
• 4296-CTO, 3Dx
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M, non-AMT, TPM, AES 04W1540 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M, non-AMT, non-TPM, non-AES 04W1541 N
• 4294-CTO
• 4296-CTO, 29x
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i3-2310M, non-AMT, TPM, non-AES 04W1542 N
• 4294-CTO, 2Ex, 2Dx, 27x, 26x, 25x
• 4296-CTO, 2Jx, 2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x, 23x
• 4297-CTO
• 4298-CTO, 4Fx, 4Ex, 3Nx
• 4299-CTO, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO

112 Hardware Maintenance Manual

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
5 System board assembly with Intel Core i3-2310M, non-AMT, non-TPM, non-AES 04W1543 N
• 4294-CTO, 2Cx, 2Bx
• 4296-CTO, 2Tx, 2Sx, 2Rx, 2Qx
• 4297-CTO, 22x
• 4298-CTO, 36x
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M, AMT, TPM, AES 04W3276 N
• 4294-CTO, 2Nx, 23x, 24x
• 4296-CTO, 3Jx, 3Cx, 3Bx, 36x, 33x, 32x, 2Xx, 2Wx, 2Mx, 2Lx, 2Kx, 2Bx, 22x
• 4297-CTO, 23x, 24x
• 4298-CTO, 4Yx, 4Vx, 4Hx, 4Gx, 4Cx, 4Bx, 42x, 3Zx, 3Wx, 3Vx, 3Sx, 3Rx, 3Qx, 3Px, 3Mx,
3Jx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 2Zx, 2Xx, 2Vx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx,
2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Dx, 2Ax, 28x, 27x
• 4299-CTO, 53x, 4Xx, 4Vx, 4Ux, 4Cx, 4Bx, 36x, 35x, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Qx,
2Px, 2Kx, 2Jx, 2Hx, 2Fx, 2Ax, 28x, 27x
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M, non-AMT, TPM, AES 04W3277 N
• 4294-CTO, 2Rx, 2Kx
• 4296-CTO, 27x, 26x
• 4297-CTO
• 4298-CTO, 4Xx, 4Jx, 46x, 45x
• 4299-CTO, 3Bx
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M, AMT, non-TPM, non-AES 04W3278 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO, 4Ax, 49x
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i5-2520M, non-AMT, non-TPM, non-AES 04W3279 N
• 4294-CTO, 29x, 28x
• 4296-CTO, 3Ax, 28x
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M, AMT, TPM, AES 04W3280 N
• 4294-CTO, 22x
• 4296-CTO, 3Ex, 39x, 38x, 37x, 35x, 34x, 2Zx, 2Yx, 2Ux, 2Px, 2Nx, 2Ex, 2Dx
• 4297-CTO
• 4298-CTO, 4Ux, 4Dx, 48x, 47x, 44x, 43x, 3Yx, 3Xx, 3Ux, 3Tx, 3Lx, 3Kx, 3Hx, 3Gx, 3Fx,
35x, 32x, 2Yx, 2Wx, 2Ux, 2Tx, 2Fx, 2Ex, 2Cx, 2Bx, 29x, 26x
• 4299-CTO, 54x, 4Yx, 3Ex, 3Dx, 3Cx, 3Ax, 39x, 38x, 37x, 34x, 33x, 32x, 2Zx, 2Sx, 2Rx,
2Lx, 2Gx, 2Ex, 2Dx, 2Bx, 29x, 26x
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 113

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
5 System board assembly with Intel Core i7-2620M, non-AMT, TPM, AES 04W3281 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M, AMT, non-TPM, non-AES 04W3282 N
• 4294-CTO, 2Ax
• 4296-CTO, 3Dx
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2620M, non-AMT, non-TPM, non-AES 04W3283 N
• 4294-CTO, 29x
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i3-2310M, non-AMT, TPM, non-AES 04W3284 N
• 4294-CTO, 2Ex, 2Dx, 27x, 26x, 25x
• 4296-CTO, 2Jx, 2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x, 23x
• 4297-CTO
• 4298-CTO, 4Fx, 4Ex, 3Nx
• 4299-CTO, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i3-2310M, non-AMT, non-TPM, non-AES 04W3285 N
• 4294-CTO, 2Cx, 2Bx
• 4296-CTO, 2Tx, 2Sx, 2Rx, 2Qx
• 4297-CTO, 22x
• 4298-CTO, 36x
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2640M, AMT, TPM 04W3380 N
• 4294-CTO, 2Sx, 2Mx, 2Lx, 2Jx, 2Hx
• 4296-CTO, 3Mx, 3Lx
• 4297-CTO
• 4298-CTO, 53x, 52x, 4Tx, 4Sx, 4Rx, 4Qx, 4Mx, 4Lx, 4Kx
• 4299-CTO, 52x, 4Zx, 4Wx, 4Tx
• 4300-CTO
• 4301-CTO

114 Hardware Maintenance Manual

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
5 System board assembly with Intel Core i7-2640M, AMT, non-TPM 04W3381 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2640M, non-AMT, TPM 04W3382 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO, 4Px, 4Nx
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i7-2640M, non-AMT, non-TPM 04W3383 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i3-2350M, non-AMT, TPM 04W3384 N
• 4294-CTO, 2Gx, 2Fx
• 4296-CTO, 3Nx, 3Kx, 3Hx, 3Gx, 3Fx
• 4297-CTO
• 4298-CTO, 4Zx, 4Wx
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i3-2350M, non-AMT, non-TPM 04W3385 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
5 System board assembly with Intel Core i3-2370M, non-AMT, TPM 04W3598 N
• 4294-CTO, 2Qx, 2Px, 2Ux, 2Tx
• 4296-CTO, 3Sx, 3Rx, 3Qx, 3Px
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 115

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
5 System board assembly with Intel Core i3-2370M, non-AMT, non-TPM 04W3599 N
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
6 Integrated Mobile Broadband (Gobi 3000 3G with GPS) 60Y3257 **
• 4294-CTO
• 4296-CTO, 3Bx
• 4297-CTO
• 4298-CTO, 4Gx
• 4299-CTO
• 4300-CTO
• 4301-CTO
6 Integrated Mobile Broadband (Gobi 3000 Malaysia) 60Y3283 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
6 Integrated Mobile Broadband (Ericsson F5521gw) 60Y3279 **
• 4294-CTO
• 4296-CTO, 22x
• 4297-CTO
• 4298-CTO, 53x, 48x, 47x, 32x, 2Wx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Cx, 2Bx, 29x
• 4299-CTO, 4Wx, 3Ax, 2Qx, 2Px, 2Bx
• 4300-CTO
• 4301-CTO
6 Integrated Mobile Broadband (Ericsson F5521gw Malaysia SKU) 60Y3267 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
6 Integrated China Telecom Mobile Broadband (Leadcore LC5740 TD-SCDMA) 60Y3261 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

116 Hardware Maintenance Manual

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
6 Integrated China Telecom Mobile Broadband (Huawei EM660) 60Y3239 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO, 4Lx, 4Kx, 3Hx, 3Gx, 3Bx, 3Ax
• 4299-CTO
• 4300-CTO
• 4301-CTO
7 ThinkPad b/g/n Wireless (1x1 BGN) 60Y3247 **
• 4294-CTO, 28x, 29x
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
7 ThinkPad b/g/n Wireless (1x1 BGN) 60Y3249 **
• 4294-CTO, 28x, 29x
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
7 Intel Centrino Wireless-N 1000 60Y3241 **
• 4294-CTO, 2Rx, 2Qx, 2Px, 2Kx, 2Gx, 2Fx, 2Ex, 2Cx, 2Bx, 27x, 26x
• 4296-CTO, 3Ax, 29x, 28x, 27x, 26x, 3Hx, 3Gx, 2Tx, 2Sx, 2Rx, 2Qx, 2Cx, 25x, 24x
• 4297-CTO, 22x
• 4298-CTO, 4Xx, 4Px, 4Nx, 4Jx, 46x, 45x, 4Wx, 3Nx, 36x
• 4299-CTO, 2Mx, 3Bx
• 4300-CTO
• 4301-CTO
7 Intel Centrino Advanced-N 6205 (2x2 AGN) 60Y3253 **
• 4294-CTO, 2Sx, 2Nx, 2Mx, 2Lx, 2Jx, 2Hx, 2Ax, 22x, 24x, 2Dx, 25x
• 4296-CTO, 3Mx, 3Lx, 3Ex, 3Dx, 3Bx, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx,
2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 22x, 3Qx, 3Px, 3Nx, 3Kx, 3Fx,
2Jx, 2Hx, 2Gx, 2Fx, 23x
• 4297-CTO, 23x, 24x
• 4298-CTO, 53x, 52x, 4Yx, 4Vx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Mx, 4Lx, 4Kx, 4Hx, 4Gx, 4Dx,
4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx, 3Vx, 3Ux, 3Tx, 3Sx, 3Rx,
3Qx, 3Px, 3Mx, 3Lx, 3Kx, 3Jx, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x,
35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx,
2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 27x, 4Zx, 4Fx, 4Ex
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx, 3Cx,
3Ax, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Rx, 2Qx, 2Px, 2Lx,
2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Cx, 2Bx, 2Ax, 29x, 28x, 27x, 2Nx
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 117

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
7 Intel Centrino Ultimate-N 6300 60Y3233 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO, 26x
• 4299-CTO, 39x, 38x, 37x, 2Dx, 26x
• 4300-CTO
• 4301-CTO
7 Intel Centrino Advanced-N + WiMAX 6250 60Y3195 **
• 4294-CTO, 23x
• 4296-CTO, 3Cx, 3Jx, 2Ax
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
7 Intel Centrino Advanced-N + WiMAX 6250, Russian SKU 60Y3209 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
8 Battery pack, 3 cell 42T4877 *
• 4294-CTO, 2Ux, 2Tx, 2Gx, 2Fx, 2Cx, 2Bx, 25x
• 4296-CTO, 3Cx, 39x, 2Ax, 3Sx, 3Rx, 3Hx, 3Gx, 2Tx, 2Sx, 2Rx, 2Qx, 2Cx
• 4297-CTO, 24x, 23x, 22x
• 4298-CTO, 4Vx, 4Lx, 4Kx, 4Jx, 3Lx, 3Kx, 3Jx, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax,
39x, 38x, 37x, 36x
• 4299-CTO, 2Kx
• 4300-CTO
• 4301-CTO
8 Battery pack, 6 cell 42T4879 *
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Ax, 29x, 28x, 22x, 23x,
24x, 2Ex, 2Dx, 27x, 26x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Dx, 3Bx, 3Ax, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx,
2Yx, 2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 29x, 28x, 27x, 26x, 22x,
3Qx, 3Px, 3Nx, 3Kx, 3Fx, 2Jx, 2Hx, 2Gx, 2Fx, 25x, 24x, 23x
• 4297-CTO
• 4298-CTO, 53x, 52x, 4Yx, 4Xx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Mx, 4Hx, 4Gx, 4Dx,
4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx, 3Vx, 3Ux, 3Tx,
3Sx, 3Rx, 3Qx, 3Px, 3Mx, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx,
2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x,
28x, 26x, 27x, 4Zx, 4Wx, 4Fx, 4Ex, 3Nx
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx, 3Cx,
3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx,
2Sx, 2Rx, 2Qx, 2Px, 2Lx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x,
27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO

118 Hardware Maintenance Manual

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
8 Battery pack, 6 cell 42T4881 *
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Ax, 29x, 28x, 22x, 23x,
24x, 2Ex, 2Dx, 27x, 26x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Dx, 3Bx, 3Ax, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx,
2Yx, 2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 29x, 28x, 27x, 26x, 22x,
3Qx, 3Px, 3Nx, 3Kx, 3Fx, 2Jx, 2Hx, 2Gx, 2Fx, 25x, 24x, 23x
• 4297-CTO
• 4298-CTO, 53x, 52x, 4Yx, 4Xx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Mx, 4Hx, 4Gx, 4Dx,
4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx, 3Vx, 3Ux, 3Tx,
3Sx, 3Rx, 3Qx, 3Px, 3Mx, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx,
2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x,
28x, 26x, 27x, 4Zx, 4Wx, 4Fx, 4Ex, 3Nx
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx, 3Cx,
3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx,
2Sx, 2Rx, 2Qx, 2Px, 2Lx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x,
27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
8 Battery pack, 6 cell 42T4903 *
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Ax, 29x, 28x, 22x, 23x,
24x, 2Ex, 2Dx, 27x, 26x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Dx, 3Bx, 3Ax, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx,
2Yx, 2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 29x, 28x, 27x, 26x, 22x,
3Qx, 3Px, 3Nx, 3Kx, 3Fx, 2Jx, 2Hx, 2Gx, 2Fx, 25x, 24x, 23x
• 4297-CTO
• 4298-CTO, 53x, 52x, 4Yx, 4Xx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Mx, 4Hx, 4Gx, 4Dx,
4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx, 3Vx, 3Ux, 3Tx,
3Sx, 3Rx, 3Qx, 3Px, 3Mx, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx,
2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x,
28x, 26x, 27x, 4Zx, 4Wx, 4Fx, 4Ex, 3Nx
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx, 3Cx,
3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx,
2Sx, 2Rx, 2Qx, 2Px, 2Lx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x,
27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
9 Hard disk drive rubber rails 04W1716 **
10 SATA hard disk drive, 250GB, 5,400 rpm 42T1153 **
• 4294-CTO, 25x
• 4296-CTO, 23x, 3Fx
• 4297-CTO
• 4298-CTO, 4Jx, 34x, 2Xx, 2Rx, 2Ax, 4Fx, 4Ex
• 4299-CTO, 28x
• 4300-CTO
• 4301-CTO
10 SATA hard disk drive, 250GB, 5,400 rpm 42T1167 **
• 4294-CTO, 25x
• 4296-CTO, 23x, 3Fx
• 4297-CTO
• 4298-CTO, 4Jx, 34x, 2Xx, 2Rx, 2Ax, 4Fx, 4Ex
• 4299-CTO, 28x
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 119

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
10 SATA hard disk drive, 320GB, 5,400 rpm 42T1155 **
• 4294-CTO, 2Gx, 2Fx, 2Cx, 2Bx
• 4296-CTO
• 4297-CTO, 22x
• 4298-CTO, 4Hx, 48x, 47x, 46x, 45x, 36x
• 4299-CTO, 3Ax
• 4300-CTO
• 4301-CTO
10 SATA hard disk drive, 160 GB, 7,200 rpm 42T1157 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
10 SATA hard disk drive, 160 GB, 7,200 rpm 42T1169 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
10 SATA hard disk drive, 250 GB, 7,200 rpm 42T1163 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
10 SATA hard disk drive, 250 GB, 7,200 rpm 42T1173 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

120 Hardware Maintenance Manual

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
10 SATA hard disk drive, 320 GB, 7,200 rpm 42T1159 **
• 4294-CTO, 2Hx, 28x, 22x, 24x, 2Ux, 2Ex, 2Dx, 27x, 26x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Dx, 3Cx, 3Bx, 39x, 37x, 36x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx,
2Ux, 2Nx, 2Mx, 2Kx, 2Ex, 2Bx, 2Ax, 28x, 27x, 26x, 22x, 3Qx, 3Px, 3Nx, 3Kx, 3Hx, 3Gx,
2Tx, 2Sx, 2Rx, 2Qx, 2Hx, 2Gx, 2Cx, 25x, 24x
• 4297-CTO, 23x
• 4298-CTO, 52x, 4Yx, 4Qx, 4Px, 4Mx, 4Gx, 4Dx, 4Ax, 49x, 44x, 43x, 42x, 3Zx, 3Wx, 3Vx,
3Ux, 3Tx, 3Sx, 3Rx, 3Qx, 3Px, 3Jx, 3Fx, 3Ex, 3Bx, 39x, 38x, 37x, 35x, 33x, 2Zx, 2Yx, 2Tx,
2Sx, 2Qx, 2Px, 2Nx, 2Jx, 2Hx, 2Ex, 2Dx, 2Bx, 26x, 27x, 4Zx
• 4299-CTO, 54x, 53x, 4Zx, 3Ex, 3Dx, 3Cx, 3Bx, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 2Yx,
2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Rx, 2Qx, 2Kx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Ax, 29x,
26x, 27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
10 SATA hard disk drive, 320 GB, 7,200 rpm 42T1171 **
• 4294-CTO, 2Hx, 28x, 22x, 24x, 2Ux, 2Ex, 2Dx, 27x, 26x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Dx, 3Cx, 3Bx, 39x, 37x, 36x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx,
2Ux, 2Nx, 2Mx, 2Kx, 2Ex, 2Bx, 2Ax, 28x, 27x, 26x, 22x, 3Qx, 3Px, 3Nx, 3Kx, 3Hx, 3Gx,
2Tx, 2Sx, 2Rx, 2Qx, 2Hx, 2Gx, 2Cx, 25x, 24x
• 4297-CTO, 23x
• 4298-CTO, 52x, 4Yx, 4Qx, 4Px, 4Mx, 4Gx, 4Dx, 4Ax, 49x, 44x, 43x, 42x, 3Zx, 3Wx, 3Vx,
3Ux, 3Tx, 3Sx, 3Rx, 3Qx, 3Px, 3Jx, 3Fx, 3Ex, 3Bx, 39x, 38x, 37x, 35x, 33x, 2Zx, 2Yx, 2Tx,
2Sx, 2Qx, 2Px, 2Nx, 2Jx, 2Hx, 2Ex, 2Dx, 2Bx, 26x, 27x, 4Zx
• 4299-CTO, 54x, 53x, 4Zx, 3Ex, 3Dx, 3Cx, 3Bx, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 2Yx,
2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Rx, 2Qx, 2Kx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Ax, 29x,
26x, 27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
11 Solid state drive spacers 04W1717 **
12 SATA solid state drive, 128 GB 45N8081 **
• 4294-CTO, 29x, 2Px
• 4296-CTO, 2Px
• 4297-CTO
• 4298-CTO, 4Tx, 4Rx, 4Lx, 4Cx, 4Bx, 3Yx, 3Xx, 3Mx, 3Lx, 3Kx, 3Gx, 3Ax, 2Wx, 2Mx, 2Kx
• 4299-CTO, 4Tx, 4Cx, 4Bx, 32x, 2Zx
• 4300-CTO
• 4301-CTO
12 SATA solid state drive, 128 GB 45N8007 **
• 4294-CTO, 29x, 2Px
• 4296-CTO, 2Px
• 4297-CTO
• 4298-CTO, 4Tx, 4Rx, 4Lx, 4Cx, 4Bx, 3Yx, 3Xx, 3Mx, 3Lx, 3Kx, 3Gx, 3Ax, 2Wx, 2Mx, 2Kx
• 4299-CTO, 4Tx, 4Cx, 4Bx, 32x, 2Zx
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 121

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
12 SATA solid state drive, 128 GB 45N7981 **
• 4294-CTO, 29x, 2Px
• 4296-CTO, 2Px
• 4297-CTO
• 4298-CTO, 4Tx, 4Rx, 4Lx, 4Cx, 4Bx, 3Yx, 3Xx, 3Mx, 3Lx, 3Kx, 3Gx, 3Ax, 2Wx, 2Mx, 2Kx
• 4299-CTO, 4Tx, 4Cx, 4Bx, 32x, 2Zx
• 4300-CTO
• 4301-CTO
12 SATA solid state drive, 160 GB 45N8057 **
• 4294-CTO, 2Mx, 2Jx, 2Ax, 23x
• 4296-CTO, 3Ex, 3Ax, 38x, 35x, 34x, 2Lx, 2Dx, 29x, 2Jx, 2Fx
• 4297-CTO
• 4298-CTO, 53x, 4Ux, 4Sx, 4Nx, 4Kx, 3Hx, 3Dx, 3Cx, 32x, 2Vx, 2Ux, 2Lx, 2Gx, 2Fx, 2Cx,
29x, 28x, 3Nx
• 4299-CTO, 52x, 4Yx, 4Xx, 2Px, 2Lx, 2Jx, 2Bx
• 4300-CTO
• 4301-CTO
13 Hard disk drive cover assembly 04W1414 **
14 ThinkPad X220 UltraBase 04W1420 *
14 ThinkPad X220 UltraBase 04W1890 *
15 DVD-ROM drive 45N7485 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO
15 DVD-ROM drive 45N7521 **
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

122 Hardware Maintenance Manual

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
15 DVD/CD-RW combo drive 45N7457 **
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 22x, 23x
• 4296-CTO, 3Mx, 38x, 37x, 36x, 2Px, 2Mx, 27x, 3Qx, 2Jx, 2Hx, 25x
• 4297-CTO
• 4298-CTO, 52x, 4Dx, 44x, 43x, 42x, 3Zx, 3Fx, 3Ex, 3Dx, 33x, 2Lx, 2Kx
• 4299-CTO, 4Ux, 36x, 35x, 34x, 33x, 2Cx
• 4300-CTO
• 4301-CTO
15 DVD/CD-RW combo drive 45N7451 **
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 22x, 23x
• 4296-CTO, 3Mx, 38x, 37x, 36x, 2Px, 2Mx, 27x, 3Qx, 2Jx, 2Hx, 25x
• 4297-CTO
• 4298-CTO, 52x, 4Dx, 44x, 43x, 42x, 3Zx, 3Fx, 3Ex, 3Dx, 33x, 2Lx, 2Kx
• 4299-CTO, 4Ux, 36x, 35x, 34x, 33x, 2Cx
• 4300-CTO
• 4301-CTO
15 DVD-RAM/RW combo drive 45N7453 **
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 22x, 23x
• 4296-CTO, 3Mx, 38x, 37x, 36x, 2Px, 2Mx, 27x, 3Qx, 2Jx, 2Hx, 25x
• 4297-CTO
• 4298-CTO, 52x, 4Dx, 44x, 43x, 42x, 3Zx, 3Fx, 3Ex, 3Dx, 33x, 2Lx, 2Kx
• 4299-CTO, 4Ux, 36x, 35x, 34x, 33x, 2Cx
• 4300-CTO
• 4301-CTO
16 DIMM door kit 04W1416 **
17 Base cover assembly 04W2239 N
17 Base cover assembly 04W2240 N
18 Bluetooth daughter card 60Y3271 N
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Ax, 29x, 28x, 22x, 23x,
24x, 2Ux, 2Tx, 2Gx, 2Ex, 2Dx, 2Bx, 27x, 26x, 25x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x,
32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 2Ax, 29x, 28x,
27x, 26x, 22x, 3Sx, 3Rx, 3Qx, 3Px, 3Nx, 3Kx, 3Hx, 3Gx, 3Fx, 2Tx, 2Sx, 2Rx, 2Qx, 2Jx,
2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x, 23x
• 4297-CTO, 22x, 23x, 24x
• 4298-CTO, 53x, 52x, 4Yx, 4Xx, 4Vx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Mx, 4Lx, 4Kx,
4Gx, 4Dx, 4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx, 3Vx,
3Ux, 3Tx, 3Sx, 3Rx, 3Mx, 3Lx, 3Kx, 3Jx, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x,
38x, 37x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Qx, 2Px, 2Nx,
2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x, 27x, 4Zx,
4Wx, 4Fx, 4Ex, 3Nx, 36x
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx, 3Cx,
3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Ux, 2Tx, 2Sx, 2Rx, 2Qx,
2Px, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x, 27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 123

Table 9. Parts list - Overall (continued)
No. FRU FRU no. CRU
ID
18 Bluetooth daughter card 60Y3275 N
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Ax, 29x, 28x, 22x, 23x,
24x, 2Ux, 2Tx, 2Gx, 2Ex, 2Dx, 2Bx, 27x, 26x, 25x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x,
32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 2Ax, 29x, 28x,
27x, 26x, 22x, 3Sx, 3Rx, 3Qx, 3Px, 3Nx, 3Kx, 3Hx, 3Gx, 3Fx, 2Tx, 2Sx, 2Rx, 2Qx, 2Jx,
2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x, 23x
• 4297-CTO, 22x, 23x, 24x
• 4298-CTO, 53x, 52x, 4Yx, 4Xx, 4Vx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Mx, 4Lx, 4Kx,
4Gx, 4Dx, 4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx, 3Vx,
3Ux, 3Tx, 3Sx, 3Rx, 3Mx, 3Lx, 3Kx, 3Jx, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x,
38x, 37x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Qx, 2Px, 2Nx,
2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x, 27x, 4Zx,
4Wx, 4Fx, 4Ex, 3Nx, 36x
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx, 3Cx,
3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Ux, 2Tx, 2Sx, 2Rx, 2Qx,
2Px, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x, 27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
19 Fan assembly 04W1774 N
20 DC-in cable assembly 04W1651 N
21 ExpressCard slot 04W1413 N
22 Palm rest assembly 04W2188 N
23 Keyboard bezel assembly 04W1771 N
24 Keyboard (see “Keyboard” on page 128.)
25 TrackPoint stick caps 91P9642 *
26 80GB mSATA 45N8259 *
• 4294-CTO, 2Lx, 2Hx, 22x
• 4296-CTO, 2Ex, 3Dx
• 4297-CTO
• 4298-CTO, 4Sx, 4Rx, 4Qx, 3Lx, 3Jx, 33x, 2Sx
• 4299-CTO
• 4300-CTO
• 4301-CTO
— ac power adapter (see “ac power adapter ” on page 130.)

LCD FRUs
12.5-in. HD LED backlight LCD (Table 10 “Parts list - 12.5-in. HD LED backlight LCD for multi-touch panel
LCD or outdoor LCD” on page 125)

124 Hardware Maintenance Manual

 12

11

3
10

Table 10. Parts list - 12.5-in. HD LED backlight LCD for multi-touch panel LCD or outdoor LCD
No. FRU FRU no. CRU
ID
1 LCD panel, 12.5-in. WXGA, LED backlight for multi-touch panel 04W1545 N
• 4294-CTO, 2Nx, 2Mx, 2Lx, 2Jx, 2Hx, 2Ax, 29x, 2Sx, 2Rx, 2Qx, 2Px, 2Kx, 23x, 24x, 2Ux,
2Tx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 27x, 25x
• 4296-CTO, 3Dx, 3Cx, 2Ex, 2Dx, 2Ax, 3Mx, 3Lx, 3Jx, 3Ex, 39x, 38x, 37x, 36x, 34x, 33x,
32x, 2Yx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Bx, 29x, 28x, 22x, 3Sx, 3Rx, 3Qx, 3Px,
3Nx, 3Kx, 3Hx, 3Gx, 3Fx, 2Tx, 2Sx, 2Rx, 2Qx, 2Jx, 2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x, 23x
• 4297-CTO, 22x, 23x, 24x

Chapter 10. Parts list 125

Table 10. Parts list - 12.5-in. HD LED backlight LCD for multi-touch panel LCD or outdoor LCD (continued)
No. FRU FRU no. CRU
ID
• 4298-CTO, 4Sx, 4Rx, 4Qx, 4Jx, 4Hx, 46x, 3Jx, 35x, 33x, 2Sx, 53x, 52x, 4Yx, 4Vx, 4Ux,
4Tx, 4Px, 4Nx, 4Mx, 4Lx, 4Kx, 4Dx, 4Bx, 49x, 48x, 47x, 43x, 42x, 3Yx, 3Vx, 3Ux, 3Rx,
3Px, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 34x, 2Yx, 2Xx, 2Wx,
2Ux, 2Tx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Gx, 2Fx, 2Bx, 2Ax, 29x, 28x, 4Zx,
4Fx, 4Ex, 36x, 2Jx, 26x
• 4299-CTO, 2Cx, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Bx, 3Dx, 3Cx,
3Bx, 3Ax, 39x, 35x, 34x, 2Zx, 2Yx, 2Vx, 2Ux, 2Rx, 2Qx, 2Px, 2Kx, 2Hx, 2Ex, 29x,
28x, 2Dx, 26x
• 4300-CTO
• 4301-CTO
1 LCD panel, 12.5-in. WXGA, LED backlight for outdoor panel 04W1546 N
• 4294-CTO, 22x, 28x, 26x
• 4296-CTO, 3Bx, 3Ax, 35x, 2Zx, 2Xx, 27x, 26x
• 4297-CTO
• 4298-CTO, 45x, 3Lx, 4Xx, 4Gx, 4Cx, 4Ax, 44x, 3Zx, 3Xx, 3Wx, 3Tx, 3Sx, 3Qx, 3Mx,
3Kx, 32x, 2Zx, 2Vx, 2Hx, 2Ex, 2Dx, 2Cx, 4Wx, 3Nx, 27x
• 4299-CTO, 4Cx, 3Ex, 38x, 37x, 36x, 33x, 32x, 2Xx, 2Wx, 2Tx, 2Sx, 2Lx, 2Jx, 2Gx,
2Fx, 2Bx, 2Ax, 2Nx, 2Mx, 27x
• 4300-CTO
• 4301-CTO
2 Fingerprint reader 04W1548 N
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Ax, 29x, 28x, 22x, 23x,
24x, 2Ux, 2Tx, 2Gx, 2Ex, 2Dx, 2Bx, 27x, 26x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x,
32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 2Ax, 29x,
28x, 27x, 26x, 22x, 3Sx, 3Rx, 3Qx, 3Px, 3Kx, 3Hx, 3Gx, 2Tx, 2Sx, 2Rx, 2Qx, 2Jx,
2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x
• 4297-CTO, 22x, 23x, 24x
• 4298-CTO, 53x, 52x, 4Xx, 4Vx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Mx, 4Lx, 4Kx,
4Gx, 4Dx, 4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx,
3Vx, 3Ux, 3Tx, 3Sx, 3Rx, 3Mx, 3Lx, 3Kx, 3Jx, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx, 3Bx,
3Ax, 39x, 38x, 37x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Qx,
2Px, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x,
27x, 4Wx, 3Nx, 36x
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx,
3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Ux, 2Tx, 2Sx,
2Rx, 2Qx, 2Px, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x,
26x, 27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
2 Fingerprint reader dummy 04W1549 N
• 4294-CTO, 25x, 2Cx, 2Fx
• 4296-CTO, 23x, 3Fx, 3Nx
• 4297-CTO
• 4298-CTO, 4Yx, 4Jx, 4Hx, 3Qx, 3Px, 2Rx, 2Nx, 4Zx, 4Fx, 4Ex
• 4299-CTO, 2Vx, 2Wx
• 4300-CTO
• 4301-CTO

126 Hardware Maintenance Manual

Table 10. Parts list - 12.5-in. HD LED backlight LCD for multi-touch panel LCD or outdoor LCD (continued)
No. FRU FRU no. CRU
ID
3 Integrated camera 04W1364 N
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Ax, 29x, 28x, 22x, 23x,
24x, 2Ux, 2Tx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 27x, 26x, 25x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 2Zx,
2Yx, 2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 2Ax, 29x, 28x, 27x, 26x,
22x, 3Sx, 3Rx, 3Qx, 3Px, 3Nx, 3Kx, 3Hx, 3Gx, 3Fx, 2Tx, 2Sx, 2Rx, 2Qx, 2Jx, 2Hx, 2Gx,
2Fx, 2Cx, 25x, 24x, 23x
• 4297-CTO, 22x, 23x, 24x
• 4298-CTO, 53x, 52x, 4Yx, 4Xx, 4Vx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Mx, 4Lx,
4Kx, 4Gx, 4Dx, 4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx,
3Wx, 3Vx, 3Ux, 3Tx, 3Sx, 3Rx, 3Mx, 3Lx, 3Kx, 3Jx, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx,
3Bx, 3Ax, 39x, 38x, 37x, 35x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Px,
2Nx, 2Mx, 2Lx, 2Kx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 4Zx, 4Wx,
4Fx, 4Ex, 3Nx, 36x
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx, 3Cx,
3Bx, 3Ax, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Ux, 2Tx, 2Sx, 2Rx, 2Qx, 2Px, 2Lx,
2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Cx, 2Bx, 2Ax, 29x, 28x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
4 LCD cable assembly 04W1775 N
4 LED cable assembly 04W1776 N
5 Wireless LAN antenna assembly 04W1779 N
6 Wireless WAN antenna assembly 04W1778 N
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Kx, 23x, 24x, 2Ux, 2Tx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx,
2Bx, 27x, 26x, 25x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx,
2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Bx, 29x, 28x, 27x, 26x, 3Sx, 3Rx, 3Qx, 3Px,
3Nx, 3Kx, 3Hx, 3Gx, 3Fx, 2Tx, 2Sx, 2Rx, 2Qx, 2Jx, 2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x, 23x
• 4297-CTO, 22x, 23x, 24x
• 4298-CTO, 52x, 4Yx, 4Xx, 4Vx, 4Ux, 4Tx, 4Px, 4Nx, 4Mx, 4Dx, 4Cx, 4Bx, 4Ax, 49x, 44x,
43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx, 3Vx, 3Ux, 3Tx, 3Sx, 3Rx, 3Qx, 3Px, 3Mx, 3Kx, 3Fx, 3Ex,
3Dx, 3Cx, 39x, 38x, 37x, 2Zx, 2Yx, 2Xx, 2Vx, 2Ux, 2Tx, 2Rx, 2Qx, 2Px, 2Nx, 2Fx, 2Ex,
2Dx, 2Ax, 28x, 26x, 27x, 4Zx, 4Wx, 4Fx, 4Ex, 3Nx, 36x
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx, 3Cx, 3Bx,
36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Rx, 2Lx, 2Kx, 2Jx,
2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Ax, 29x, 28x, 26x, 27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
6 Wireless WAN antenna assembly dummy 04W1780 N
• 4294-CTO, 2Nx, 2Mx, 2Jx, 2Ax, 29x, 28x
• 4296-CTO, 2Ax, 2Dx, 3Cx
• 4297-CTO
• 4298-CTO, 4Jx, 4Hx, 46x, 45x, 35x, 34x
• 4299-CTO, 37x, 38x, 39x
• 4300-CTO
• 4301-CTO
7 LCD rear cover assembly 04W1772 N
8 Hinges 04W1773 N
9 LED card 04W1777 N
10 Speaker assembly 04W1782 N

Chapter 10. Parts list 127

Table 10. Parts list - 12.5-in. HD LED backlight LCD for multi-touch panel LCD or outdoor LCD (continued)
No. FRU FRU no. CRU
ID
11 LCD button bezel with fingerprint reader 04W1550 N
• 4294-CTO, 2Sx, 2Rx, 2Qx, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Ax, 29x, 28x, 22x, 23x,
24x, 2Ux, 2Tx, 2Gx, 2Ex, 2Dx, 2Bx, 27x, 26x
• 4296-CTO, 3Mx, 3Lx, 3Jx, 3Ex, 3Dx, 3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x,
32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Ux, 2Px, 2Nx, 2Mx, 2Lx, 2Kx, 2Ex, 2Dx, 2Bx, 2Ax, 29x,
28x, 27x, 26x, 22x, 3Sx, 3Rx, 3Qx, 3Px, 3Kx, 3Hx, 3Gx, 2Tx, 2Sx, 2Rx, 2Qx, 2Jx,
2Hx, 2Gx, 2Fx, 2Cx, 25x, 24x
• 4297-CTO, 22x, 23x, 24x
• 4298-CTO, 53x, 52x, 4Xx, 4Vx, 4Ux, 4Tx, 4Sx, 4Rx, 4Qx, 4Px, 4Nx, 4Mx, 4Lx, 4Kx,
4Gx, 4Dx, 4Cx, 4Bx, 4Ax, 49x, 48x, 47x, 46x, 45x, 44x, 43x, 42x, 3Zx, 3Yx, 3Xx, 3Wx,
3Vx, 3Ux, 3Tx, 3Sx, 3Rx, 3Mx, 3Lx, 3Kx, 3Jx, 3Hx, 3Gx, 3Fx, 3Ex, 3Dx, 3Cx, 3Bx,
3Ax, 39x, 38x, 37x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Wx, 2Vx, 2Ux, 2Tx, 2Sx, 2Qx,
2Px, 2Mx, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x, 26x,
27x, 4Wx, 3Nx, 36x
• 4299-CTO, 54x, 53x, 52x, 4Zx, 4Yx, 4Xx, 4Wx, 4Vx, 4Ux, 4Tx, 4Cx, 4Bx, 3Ex, 3Dx,
3Cx, 3Bx, 3Ax, 39x, 38x, 37x, 36x, 35x, 34x, 33x, 32x, 2Zx, 2Yx, 2Xx, 2Ux, 2Tx, 2Sx,
2Rx, 2Qx, 2Px, 2Lx, 2Kx, 2Jx, 2Hx, 2Gx, 2Fx, 2Ex, 2Dx, 2Cx, 2Bx, 2Ax, 29x, 28x,
26x, 27x, 2Nx, 2Mx
• 4300-CTO
• 4301-CTO
11 LCD button bezel without fingerprint reader 04W1666 N
• 4294-CTO, 25x, 2Cx, 2Fx
• 4296-CTO, 23x, 3Fx, 3Nx
• 4297-CTO
• 4298-CTO, 4Yx, 4Jx, 4Hx, 3Qx, 3Px, 2Rx, 2Nx, 4Zx, 4Fx, 4Ex
• 4299-CTO, 2Vx, 2Wx
• 4300-CTO
• 4301-CTO
12 Icon plate for X220 Tablet 04W2044 N
— N

Keyboard
Table 11. Parts list - Keyboard
Language P/N CRU ID
Arabic 45N2216 45N2076 45N2146 **
Belgian 45N2217 45N2077 45N2147
Brazilian Portuguese 45N2215 45N2075 45N2145
Bulgarian 45N2218 45N2078 45N2148
Canadian French (058) 45N2213 45N2073 45N2143
Canadian French (Acnor) 45N2212 45N2072 45N2142
Czech 45N2219 45N2079 45N2149
Danish 45N2220 45N2080 45N2150
Dutch 45N2230 45N2090 45N2160
French 45N2222 45N2082 45N2152
German 45N2223 45N2083 45N2153
Greek (U.S. English and Greek layout) 45N2224 45N2084 45N2154

128 Hardware Maintenance Manual

Table 11. Parts list - Keyboard (continued)
Language P/N CRU ID
Hungarian 45N2226 45N2086 45N2156
Icelandic 45N2227 45N2087 45N2157
Israel (Hebrew) 45N2225 45N2085 45N2155
Italian 45N2228 45N2088 45N2158
Japanese 45N2242 45N2102 45N2172
Kazakhstan 45N2229 45N2089 45N2159
Korean 45N2243 45N2103 45N2173
Latin American Spanish 45N2214 45N2074 45N2144
Norwegian 45N2231 45N2091 45N2161
Polish 45N2232 45N2092 45N2162
Portuguese 45N2233 45N2093 45N2163
Russian 45N2234 45N2094 45N2164
Slovak 45N2235 45N2095 45N2165
Slovenian 45N2236 45N2096 45N2166
Swedish, Finnish 45N2237 45N2097 45N2167
Spanish 45N2221 45N2081 45N2151
Swiss 45N2238 45N2098 45N2168
Thai 45N2245 45N2105 45N2175
Traditional Chinese 45N2244 45N2104 45N2174
Turkish 45N2239 45N2099 45N2169
Turkish (F Type) 60Y9550 60Y9552 60Y9554
U.K. English 45N2240 45N2100 45N2170
U.S. English 45N2211 45N2071 45N2141
U.S. English (International, with a Euro symbol) 45N2241 45N2101 45N2171

Miscellaneous parts
Table 12. Parts list - Miscellaneous parts
FRU P/N CRU
ID
Screw kit: 04W1785 N
• M2 × 3 mm, (2)
• M2 × 3.5, mm (31)
• M2 × 5 mm, (10)
• M2 × 2 mm, (1)
• M2 × 3.5 mm, (3)
• M2 × 3 mm, (8)
• M2.5 × 6 mm, (9)
• M3 × 3.5 mm , (1)
• Hex stud, (2)
• IMS 2 x 5 mm, (10)
• LCM LCD bezel screw mylar, (3)
• LCM LCD bezel screw mylar, (3)
• LCD side screw mylar, (8)

Chapter 10. Parts list 129

Table 12. Parts list - Miscellaneous parts (continued)
FRU P/N CRU
ID
• LCD side screw mylar, (8)
• Microphone support mylar, (1)
• Microphone support mylar, (1)
• Name plate, (1)
• Name plate, (1)
Base cover miscellaneous parts kit: 04W1547 N
• Screw M2 x 2, (1)
• Screw M2 x 3.5, (3)
• Step screw M1.6 x 3, (1)
• Pen push
• Pen switch
• Base cover bracket
• DC-in cable bracket
• Front rubber foot, (2)
• Rear rubber foot left
• Rear rubber foot right
• Battery latch right
• Battery latch left
• Battery knob right
• Battery knob left
• Battery latch spring
System miscellaneous parts kit: 04W1784 N
• EMI touch pad conductive clothes LDB-1
• Touch pad mylar
• EMI gasket, (2)
• Name plate mylar
• LCD side screw mylar, (8)
• LCD conductive tape cateron LCO-1, (2)
• Sponge panel 01
• Sponge panel 02, (4)
• Sponge 09 panel LCO-1
• Sponge 10 panel LCO-1
Rubber kit 04W1783 N

ac power adapter
Table 13. Parts list - ac power adapters
FRU P/N CRU
ID
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxY, xxU) 42T5282 *
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxY, xxU) 42T4419
2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxY, xxU) 42T4423
3-pin (65W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxT, xxV) OP 42T5283
3-pin (65W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxT, xxV) OP 42T4417
3-pin (65W, 20 V) adapter (models CTO, xxA, xxB, xxC, xxG, xxH, xxK, xxM, xxT, xxV) OP 42T4421

Power cords
A ThinkPad power cord for a specific country or region is usually available only in that country or region:

130 Hardware Maintenance Manual

Table 14. Parts list - 2-pin power cords
Country or region FRU no. CRU
ID
Argentina 42T5020 42T5105 *
• Models: CTO, xxY
Brazil 42T5180 42T5183
• Models: CTO, xxP
Canada, U.S. 42T5008 42T5093
• Models: CTO, xxF, xxL, xxS, xxU
Japan 42T5014 42T5099
• Models: CTO, xxE, xxJ

Table 15. Parts list - 3-pin power cords

Country or region FRU no. CRU
ID
Australia, New Zealand 42T5050 42T5135 *
• Models: CTO, xxM
Bangladesh, Sri Lanka, South Africa 42T5056 42T5141
• Models: CTO, xxG
Canada, U.S. 42T5004 42T5089
• Models: CTO, xxG, xxT
China (P.R.C.) (other than Hong Kong S.A.R.) 42T5065 42T5150
• Models: CTO, xxC
Denmark 42T5041 42T5126
• Models: CTO, xxG
European countries 42T5029 42T5114
• Models: CTO, xxG
India 42T5083 42T5168
• Models: CTO, xxQ
Israel 42T5062 42T5147
• Models: CTO, xxG
Italy 42T5047 42T5132
• Models: CTO, xxG
Korea 42T5077 42T5162
• Models: CTO, xxK
Switzerland 42T5044 42T5129
• Models: CTO, xxG
Taiwan 42T5071 42T5156
• Models: CTO, xxV
U.K., China (Hong Kong S.A.R.) 42T5035 42T5120
• Models: CTO, xxB, xxG, xxH

Recovery discs

Windows XP Professional DVDs

Note: The Windows XP Professional recovery DVDs are available only for models with a valid Microsoft
Windows XP Professional certificate of authenticity (COA) affixed to the system. Due to a Microsoft licensing

Chapter 10. Parts list 131

limitation, if a model came with Windows XP Professional preinstalled from the factory, but has either a
Windows 7 or Windows Vista COA affixed to the system, that model is eligible only for recovery DVDs that
match the operating system specified on the COA.
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Table 16. Parts list - Windows XP Professional (32 bit) recovery DVDs
Language P/N CRU
ID
Japanese 03W8394 *
English 03W8395

Windows XP Tablet (32 bit) DVDs

Note: The Windows XP Professional recovery DVDs are available only for models with a valid Microsoft
Windows XP Professional certificate of authenticity (COA) affixed to the system. Due to a Microsoft licensing
limitation, if a model came with Windows XP Professional preinstalled from the factory, but has either a
Windows 7 or Windows Vista COA affixed to the system, that model is eligible only for recovery DVDs that
match the operating system specified on the COA.
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO

Table 17. Parts list - Windows XP Tablet (32 bit) recovery DVDs
Language P/N CRU
ID
English 04X0000 *
Japanese 03W8396

Windows Vista Business (32 bit) DVDs

Note: The Windows Vista recovery DVDs are available only for models with a valid Microsoft Windows Vista
certificate of authenticity (COA) affixed to the system. Due to a Microsoft licensing limitation, if a model came
with Windows Vista Business or Windows Vista Ultimate preinstalled from the factory, but has a Windows 7
COA affixed to the system, that model is eligible only for recovery DVDs that match the operating system
specified on the COA.
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

132 Hardware Maintenance Manual

Table 18. Parts list - Windows Vista Business (32 bit) recovery DVDs
Language P/N CRU
ID
English 04T2211 *
Japanese 04T2210

Windows Vista Home Basic (32 bit) DVDs

Note: The Windows Vista recovery DVDs are available only for models with a valid Microsoft Windows Vista
certificate of authenticity (COA) affixed to the system. Due to a Microsoft licensing limitation, if a model came
with Windows Vista Business or Windows Vista Ultimate preinstalled from the factory, but has a Windows 7
COA affixed to the system, that model is eligible only for recovery DVDs that match the operating system
specified on the COA.
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Table 19. Parts list - Windows Vista Home Basic (32 bit) recovery DVDs
Language P/N CRU
ID
English 04T2212 *

Windows 7 Professional (32 bit) DVDs

Windows 7 Professional (32 bit) is preinstalled as the operating system in the following models:
• 4294-CTO
• 4296-CTO, 3Cx, 3Jx
• 4297-CTO, 23x
• 4298-CTO, 36x, 37x, 38x, 4Hx, 4Jx
• 4299-CTO, 2Kx
• 4300-CTO
• 4301-CTO

Table 20. Parts list - Windows 7 Professional (32 bit) recovery DVDs
Language P/N CRU
ID
English 04T2218 *
Japanese 04T2216
Simplified Chinese 04T2213
French 04T2214
German 04T2215
Spanish 04T2217
English, Danish, Finnish, Swedish, and Norwegian 04T2219
English, Dutch, French, German, and Italian 04T2220

Chapter 10. Parts list 133

Windows 7 Ultimate (32 bit) DVDs
• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Table 21. Parts list - Windows 7 Ultimate (32 bit) recovery DVDs
Language P/N CRU
ID
English 04T2221 *

Windows 7 Professional (64 bit) DVDs

Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models:
• 4294-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Dx, 2Ex
• 4296-CTO, 22x, 24x, 25x, 26x, 27x, 28x, 29x, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx,
2Nx, 2Px, 2Tx, 2Ux, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 34x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Dx, 3Ex, 3Kx
• 4297-CTO
• 4298-CTO, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px,
2Qx, 2Rx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 35x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx,
3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x,
46x, 47x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Fx, 4Gx, 4Kx, 4Lx
• 4299-CTO, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Lx, 2Mx, 2Nx, 2Px, 2Qx, 2Rx,
2Sx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 2Yx, 2Zx, 32x, 33x, 34x, 35x, 36x, 3Ax, 3Bx, 3Dx, 3Ex, 4Bx, 4Cx
• 4300-CTO
• 4301-CTO

Table 22. Parts list - Windows 7 Professional (64 bit) recovery DVDs
Language P/N CRU
ID
Arabic 04T2222 *
Brazilian Portuguese 04T2223
Czech 04T2226
English, Danish, Finnish, Swedish, and Norwegian 04T2246
English, Dutch, French, German, and Italian 04T2247
English, Slovenian, and Croatian 04T2248
French 04T2228
German 04T2230
Greek 04T2229
Hebrew 04T2231
Hungarian 04T2233
Indian English 04T2227
Japanese 04T2234
Korean /English 04T2235

134 Hardware Maintenance Manual

Table 22. Parts list - Windows 7 Professional (64 bit) recovery DVDs (continued)
Language P/N CRU
ID
Polish 04T2236
Portuguese 04T2237
Romanian 04T2238
Russian 04T2239
Serbian-Latin 04T2242
Simplified Chinese 04T2224
Slovakian 04T2240
Spanish 04T2241
Traditional Chinese 04T2225
Traditional Chinese (Hong Kong S.A.R.) 04T2232
Turkish 04T2243
US English 04T2245
US English (Disabled) 04T2244

Windows 7 Ultimate (64 bit) DVDs

• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Table 23. Parts list - Windows 7 Ultimate (64 bit) recovery DVDs
Language P/N CRU
ID
English 04T2249 *

Windows 7 Home Basic (32 bit) DVDs

• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Chapter 10. Parts list 135

Table 24. Parts list - Windows 7 Home Basic (32 bit) DVDs
Language P/N CRU
ID
Arabic 04T2250 *
Brazilian Portuguese 04T2251
English 04T2260
Indian English 04T2253
French 04T2254
Portuguese 04T2255
Russian 04T2256
Serbian-Latin 04T2258
Simplified Chinese 04T2252
Spanish 04T2257
Turkish 04T2259

Windows 7 Home Basic (64 bit) DVDs

• 4294-CTO
• 4296-CTO
• 4297-CTO
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Table 25. Parts list - Windows 7 Home Basic (64 bit) DVDs
Language P/N CRU
ID
Simplified Chinese 04T2848 *

Windows 7 Home Premium (32 bit) DVDs

Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models:
• 4294-CTO, 2Bx, 2Cx, 2Fx, 2Gx
• 4296-CTO, 2Qx, 2Rx, 3Gx
• 4297-CTO, 22x
• 4298-CTO
• 4299-CTO
• 4300-CTO
• 4301-CTO

Table 26. Parts list - Windows Home Premium (32 bit) recovery DVDs
Language P/N CRU
ID
English 04T2263 *
Indian English 04T2262
Simplified Chinese 04T2261

136 Hardware Maintenance Manual

Windows 7 Home Premium (64 bit) DVDs
• 4294-CTO
• 4296-CTO, 23x, 2Sx, 33x, 3Fx, 3Hx
• 4297-CTO
• 4298-CTO, 4Ex
• 4299-CTO, 37x, 38x, 39x
• 4300-CTO
• 4301-CTO

Table 27. Parts list - Windows 7 Home Premium (64 bit) recovery DVDs
Language P/N CRU
ID
Arabic 04T2264 *
Brazilian Portuguese 04T2265
Czech 04T2268
English, Danish, Finnish, Swedish, and Norwegian 04T2287
English, Dutch, French, German, and Italian 04T2288
English, Slovenian, and Croatian 04T2289
French 04T2269
German 04T2271
Greek 04T2270
Hebrew 04T2272
Hungarian 04T2274
Japanese 04T2275
Korean /English 04T2276
Polish 04T2277
Portuguese 04T2278
Romanian 04T2279
Russian 04T2280
Serbian-Latin 04T2283
Simplified Chinese 04T2266
Slovakian 04T2281
Spanish 04T2282
Traditional Chinese 04T2267
Traditional Chinese (Hong Kong S.A.R.) 04T2273
Turkish 04T2284
US English 04T2286
US English (Disabled) 04T2285

Chapter 10. Parts list 137

Common service tools
Table 28. Parts list - Common service tools
Tool P/N
Screwdriver kit 95F3598
1/4" drive spinner handle 1650840
1/4" Sq. to 1/4" hex torx adapter 93F2838
TR7-TR-10 tamper resistant torx bits 00P6967
Removal tool antenna RF connector 08K7159
USB 2.0 CD-RW/DVD-ROM combo drive II 40Y8687
USB cable 40Y8704
USB floppy diskette drive for maintenance diskette 05K9283
USB floppy diskette drive tool kit 27L3452
Test card for integrated Smart Card 42W7820
ThinkPad Hardware Maintenance Diskette Version 1.73 or later -
Note: Download the file from the following Web site: http://www.lenovo.com/spm

Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult
your local Lenovo representative for information on the products and services currently available in your
area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that
Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service
that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's
responsibility to evaluate and verify the operation of any other product, program, or service.

Lenovo may have patents or pending patent applications covering subject matter described in this
document. The furnishing of this document does not give you any license to these patents. You can send
license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing

LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow
disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply
to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication.
Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.

The products described in this document are not intended for use in implantation or other life support
applications where malfunction may result in injury or death to persons. The information contained in this

138 Hardware Maintenance Manual

document does not affect or change Lenovo product specifications or warranties. Nothing in this document
shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo
or third parties. All information contained in this document was obtained in specific environments and is
presented as an illustration. The result obtained in other operating environments may vary.

Lenovo may use or distribute any of the information you supply in any way it believes appropriate without
incurring any obligation to you.

Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in
any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of
the materials for this Lenovo product, and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled environment. Therefore, the result
obtained in other operating environments may vary significantly. Some measurements may have been
made on development-level systems and there is no guarantee that these measurements will be the same
on generally available systems. Furthermore, some measurements may have been estimated through
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their
specific environment.

Electronic emissions notices

For electronic emission information on Class B digital devices, refer to the corresponding information in
the User Guide.

Trademarks
The following terms are trademarks of Lenovo in the United States, other countries or both:

Active Protection System

Lenovo
Rescue and Recovery
ThinkPad
ThinkVantage
TrackPoint
UltraBase
Ultrabay
UltraNav

The following terms are trademarks of Microsoft Corporation in the United States, other countries, or both:
Windows
Windows Vista

The following are trademarks of Intel Corporation or its subsidiaries in the United States, other countries, or
both:
Intel
Intel Celeron
Intel Core 2 Duo
Intel Core 2 Solo

Other company, product, or service names may be the trademarks or service marks of others.

Chapter 10. Parts list 139

140 Hardware Maintenance Manual
Part Number: 0A60175_03

Printed in China

(1P) P/N: 0A60175_03

*0A60175_03*