Direction of Ethernet Connection
Parameter of Ethernet
Wire & Wireless Parameter
Spec43: Connect mode. 0=Disable; 1=Server Mode; 2=Client Mode (Using in WAN normally).
Spec44: Re-connect interval. Please keep default.
Spec45: Re-configuration if parameter changes. Please keep default.
Spec150~153: Device IP. If Spec153=0, the device will use DHCP to obtain an IP automatically.
Spec154~157: PC IP. This IP only used in Client Mode(Spec43=2).
Spec158~161: Default gateway.
Spec162~165: Subnet mask.
Spec170~173: Primary DNS.
GlobalText19: Server’s Domain Name: Only used in client mode, and Spec154~157 all are “0”
Wireless Only Parameter (Only for device whose integration Wi-Fi)
Spec50: 0=Using Wire-Ethernet; 1=Using Wireless-Ethernet. (Reboot after you change this parameter)
Spec51: Security Mode: 0=No Security; 1=WEP; 2=WPA/WPA2
Spec53: Domain Type: 0: FCC; 1: IC; 2: ETSI; 3: Spain; 4: France; 5: JapanA; 6: JapanB (Please keep
default if you do not know it)
GlobalText15: Wi-Fi SSID.
GlobalText16: Wi-Fi Security Password.
Operation steps of Connecting to Wi-Fi
1. Get a wireless router or AP, set its “Security Mode”, “SSID” and “Security Password”.
2a. Edit Spec50=1, Spec51=“Security Mode”, GlobalText15=“SSID”, GlobalText16=“Security Password”
in software, and download them by USB-Disk.
2b. Or, Edit Spec50=1, Spec51=“Security Mode”, GlobalText15=“SSID”, GlobalText16=“Security
Password” by device keypad operation. (May a little difficult)
3. Reboot device after Step.2
4. Connecting your PC to Wi-Fi router or AP, open TM-xA software’s Etherent Menu.
If you faild to search device in TM-xA software, press keys in order: Prog, 4, 2, Confirm, Confirm. Device
will display Wi-Fi link status.
Link Success: Wi-Fi connected.
AP Not Found: Device do not found the AP whose SSID=GlobalText15. Check whether GlobalText15 is
correctly.
Link in prog: Try to connect or try to get rssi now.
Failed Join/ Failed Authent/ Failed Associa/ FailedSecurit: Securit not right, check whether GlobalText16
and Spec51 is right.
i
Direction of Ethernet Connection
1. LAN：Using DHCP function to connect
Router or Server
With DHCP Function
Straight Straight
Through Through
h
gh
Cab hroug
ble ou
C a T hr
tin g
le
ht T
ht
Set
aig
ai g
Str
St r
Setting
Setting
ting
Se t
Spec153=0, means enable DHCP
The factory default is enable DHCP.
So new device can connecting into LAN
without any settings.
ii
Direction of Ethernet Connection
2. LAN: Set IP
HUB or Server
Without DHCP
Straight Straight
Through Through
h
gh
Cab hroug
ble ou
Ca Thr
le
tT
t
igh
i gh
a
a
Str
Str
Setting
Setting
Setting
tin g
Se t
Spec150～153＝IP Address (First 3 segment
must same as PC's IP address, and the last
segment should different by device)
Spec158～161=Gateway (Must same as PC)
Spec162～165=Subnet mask (Do not change，
same as PC，255.255.255.0)
iii
Direction of Ethernet Connection
3. Single Device Connection
Crossover Cable
Setting
Setting
Spec150～153＝IP Address (First 3 segment
must same as PC's IP address, and the last
segment should different by device)
Spec158～161=Gateway (Here set value as PC's
IP Address)
Spec162～165=Subnet mask (Do not change，
same as PC，255.255.255.0)
iv
Direction of Ethernet Connection
4. WAN Connection
WAN PC Need fixed
Internet WAN IP
For example：Server IP
116.226.80.84
设定
设定
设定
Spec150～153
Spec158～161 Setting based on different LAN
Spec162～165
Using Client Mode: Spec43=2
Spec154～157=Server IP：116.226.80.84
Or Keep Spec154～157=0, Set "Global Text 19, Server's Domain Name"
v
Direction of Ethernet Connection
5. Ethernet Cable
T568A T568B Pins on plug face
Pin T568A Color T568B Color
Pair Pair (Socket is reversed)
1 3 2
white/green stripe white/orange stripe
2 3 2
green solid orange solid
3 2 3
white/orange stripe white/green stripe
4 1 1
blue solid blue solid
5 1 1
white/blue stripe white/blue stripe
6 2 3
orange solid green solid
7 4 4
white/brown stripe white/brown stripe
8 4 4
brown solid brown solid
Ethernet Straight Through Cable
T568B T568B
Ethernet Crossover Cable
T568A T568B
vi
