Scribd
Upload
159 views2 pages

Removal: Torx Screw Screw Case

1. The document provides instructions for removing the tilt steering column on a 2000 Toyota Echo. 2. Key steps include removing the steering wheel pad, steering wheel, column lower and upper covers, spiral cable, switches, and disconnecting the sliding yoke and intermediate shaft assemblies. 3. Matchmarks should be made between removed parts and their mounting locations to ensure proper reinstallation.

Uploaded by

juan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
159 views2 pages

Removal: Torx Screw Screw Case

1. The document provides instructions for removing the tilt steering column on a 2000 Toyota Echo. 2. Key steps include removing the steering wheel pad, steering wheel, column lower and upper covers, spiral cable, switches, and disconnecting the sliding yoke and intermediate shaft assemblies. 3. Matchmarks should be made between removed parts and their mounting locations to ensure proper reinstallation.

Uploaded by

juan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SR−11

STEERING − TILT STEERING COLUMN


SR0ZK−01

Torx Screw Screw Case REMOVAL


1. REMOVE STEERING WHEEL PAD
NOTICE:
If the airbag connector is disconnected with the ignition
switch at ON, DTCs will be recorded.
(a) Place the front wheels facing straight ahead.
(b) Using a torx socket wrench, loosen the 2 torx screws until
the groove along the screw circumference catches on the
F08002
screw case.

(c) Pull out the wheel pad from the steering wheel and dis-
connect the airbag connector.
(d) Disconnect the connector.
CAUTION:
S When storing the wheel pad, keep the upper surface
of the pad facing upward.
S Never disassemble the wheel pad.
NOTICE:
When removing the wheel pad, take care not to pull the air-
bag wire harness.
Airbag Connector
Correct Wrong

F09849

Matchmarks 2. REMOVE STEERING WHEEL


(a) Remove the steering wheel set nut.
(b) Place matchmarks on the steering wheel and main shaft
assembly.
(c) Using SST, remove the steering wheel.
SST 09950−50012 (09951−05010, 09952−05010,
09953−05020, 09954−05020)
SST
3. REMOVE COLUMN LOWER COVER
F08004 Remove the 3 screws and column lower cover.
4. REMOVE SPIRAL CABLE, LIGHT CONTROL SWITCH
AND HEADLIGHT DIMMER SWITCH, WIPER AND
WASHER SWITCH AND COLUMN UPPER COVER
(a) Disconnect the 3 connectors from the spiral cable, light
control switch and headlight dimmer switch and wiper and
washer switch.
(b) Disconnect the airbag connector from the spiral cable.

2000 ECHO (RM750U)

Author: Date: 1001


SR−12
STEERING − TILT STEERING COLUMN

(c) Push the claw and pull out the light control switch and
headlight dimmer switch.
(d) Employ the same manner described above to the wiper
and washer switch.

F09907

(e) Slide the column upper cover and remove the spiral
cable.
NOTICE:
Do not disassemble the spiral cable or apply oil to it.
(f) Remove the column upper cover.
5. A/T:
REMOVE KEY INTERLOCK CABLE
(See page AX−18)
F09906 6. REMOVE NO. 2 COLUMN HOLE COVER
Remove the clip and No. 2 column hole cover.
7. DISCONNECT SLIDING YOKE
(a) Place matchmarks on the sliding yoke and No. 3 inter-
Matchmarks
mediate shaft assembly.
A (b) Loosen the bolt A and remove the bolt B, then disconnect
the sliding yoke.
8. REMOVE STEERING COLUMN ASSEMBLY
B
(a) Disconnect the connectors.
(b) Remove the lower mount bolt, 2 upper mount bolts and
F08008 steering column assembly.
9. REMOVE SLIDING YOKE
Remove the bolt A and sliding yoke.

10. REMOVE NO. 2 INTERMEDIATE SHAFT ASSEMBLY


(a) Place matchmarks on the No. 2 intermediate shaft as-
sembly and main shaft assembly.
(b) Remove the bolt and No. 2 intermediate shaft assembly.

Matchmarks

F08009

2000 ECHO (RM750U)

Author: Date: 1002

You might also like