JOB HAZARD ANALYSIS [JHA] WORKSHEET
JHA NO. PTW NO WORK PERMIT TYPE Hot work
FACILITY GIFT LOCATION GIFT / NEAR GIS SPECIFIC WORK STATION SEPCOO III early comb
WORK
EQUIPMENT NO DESCRIPTION
Welding and catting fence by welding machine
NOTE:
1. JHA shall be applicable for all work activities which requires PTW.
2. The pre-prepared JHA and JHA prompters will be used as a reference/guide during the development of JHA.
3. Personnel carrying out the work shall be fully familiar with the written Work/Operating Procedures developed for the job. The Work/Operating Procedures shall describe, in step-by-step
instructions, the correct method of executing the specified work.
4. Prior to commencement of work (after PTW has been approved), the task-specific JHA shall be discussed amongst all personnel involved in the execution; and requirements contained
therein shall be fully understood and agreed by all involved personnel.
DESCRIPTION POTENTIAL POTENTIAL ACTION RECOVERY
JOB STEP CONTROL BARRIERS
OF JOB STEP HAZARD CONSEQUENCES PARTY BARRIERS
Access to Preparation to Slip, trip & fall Minor injury (Laceration, , Obtain/ display approved PTW at Site SEPCOO Communication
working Area make proper hazards if improper contusion or wound) Organize toolbox meeting & share the Work s must be
access and storing of material, approved JHA with all personnel that leader or available during
egress into the equipment, etc. Body strain and sprain if involve with the work HSE the work
work area poor lifting or handling Ensure adequate precaution and access Supervisor activity.
Pinch point while are in place to allow the work to progress
unloading of blocks or Serious injury; Fracture safely
Driving to the tools or body or part of the Mixer machine must be inspected and
jobsite body crush upon contact approved by PCIHBV personnel
Manual handling/ with vehicles Ensure entire work area barricaded and
ergonomics issue .Complete all required properly secured from unauthorized
inspection for the personnel.
Vehicular accident: equipment Wear appropriate PPE including any other
taking turns too • Carry out as required
sharp; hitting objects physical checks and Provide traffic controller or banksman to
or people maintenance works of control any vehicles movement
grinding machine Inspect and ensure all other working tool
regularly free from damage.
•Ensure the grinder guard Competent driver: watch turning radius or
is correctly installed apply wide turns if required
Provide first aider c/w 1 unit of First aid box
with sufficient content
Close monitoring & supervision required
B- Injury to personnel • Wear reflective hi-vis All Worker/Supervisor/ Vehicle Operator First aid Supervisor/Medi
Welding and Presence of toxic Damage to vests when exposed to Check for loose cable connections or poor sent to c
catting fence by and flammable Equipment vehicular traffic insulation medic
welding gas Defective equipment • Isolate equipment swing • Ensure proper grounding with
machine areas copper rods and clamps of electric supply
Electric shock and • Make eye contact wit generator
electrocution and Barricade or enclose the • Keep the power supply cable
injuries work area h operators secured and properly routed
before approaching
equipment,
•
• Restrict work area entry
to authorized personnel
only during construction
activities, Wear hard
hats, safety glasses with
side shields, and steel-
toe safety boots
• Understand and review
hand signals
• Rebar that is used as
location markers or any
protruding object shall be
removed or covered with
rebar caps.
Fire / explosion - Injury to • Use hearing protection All Worker/Supervisor/ Vehicle First aid Supervisor/Medi
personnel when exposed to Operator sent to c
Trips/ Slips/ Falls excessive noise levels Wear appropriate PPE. Grinding face medic
(greater than 85 dBA shield, Grinding aprons and gloves
over an 8-hour work and fire resistant shoulder covers are
period) needed for overhead works
• Assess noise level with
sound level meter if
possibility exists that
level may exceed 85dBA
TWA
Always keep fire
extinguisher ready
for immediate use
irrespective of
location of work
Provide grinding
habitats or suitable
safety precautionary
measures with
standard fire
blankets to each
grinding location
Temperature or - Injury to • Hydration/electrolyte All Worker/Supervisor/ Vehicle First aid Supervisor/Medi
extreme winds personnel replacement fluids shall Operator sent to c
be available to prevent medic
dehydration and
work/rest periods shall be
scheduled accordingly.
• Safety glasses or
goggles shall be worn
during dust storms from
high winds
• Dust masks will be worn
if desired.
• No Scarves shall be
worn if dust masks are
available during dusty
conditions
- Injury to • All heavy equipment Supervisor/ Vehicle Operator First aid Supervisor/Medi
personnel should be inspected sent to c
before arrival onsite and medic
onsite by Contractor
• All heavy equipment
shall carry serviceable
fire extinguishers
Site Emergencies - Injury to • Personnel exposed to All Worker/Supervisor/ Vehicle First aid Supervisor/Medi
or unsafe personnel workplace violence Operator sent to c
conditions • All personnel should medic
move to muster areas at
FCP when the specified
emergency signal has
been sounded Notify
FCP Area security and
follow the directions of
security force.
House keeping Remove all the Slips, Trips, Falls due Personal injury Wear adequate PPE including suitable SEPCOO Communication
work materials, to uneven surface or (Laceration, wound, hand gloves Work s must be
equipment and poor house keeping fracture) Remove all the surplus material/ waste and leader or available during
tools from the Finger and hand injury keep the area clean & intact. HSE the work
work area Pinch between Body strain and sprain if Ensure close supervision Supervisor activity.
materials or poor lifting
machineries
Manual handling/
ergonomics issues
JHA APPROVAL DURING PTW APPLICATION
ACCEPTED BY RECEIVING AUTHORITY ACCEPTED BY RECEIVING AUTHORITY
NAME NAME
DESIGNATION DESIGNATION
SIGNATURE SIGNATURE
DATE DATE
AFTER PTW HAS BEEN APPROVED
WORK TEAM (CONFIRAMTION TEAM JHA HAS BEEN COMMUNICATED TO WORK TEAM AS PART OFPRE-JOB/TOOLBOX MEETING –
AFTER PTW BEEN APPROVED)
NAME(S) DESIGNATION SIGNATURE NAME(S) DESIGNATION SIGNATURE
