Structural Geology

Introduction
• Structural geology is the study of factors such as
origin, occurrence, classification, type and effects
of various secondary structures like folds, faults,
joints, rock cleavage and are different from those
primary structures such as bedding and vesicular
structure, which develop in rocks at the time of their
formation.
 Outcrop
• Any Geological formation exposed on the
surface is called an outcrop.
 Strike and Dip
• Strike refers to the direction in which a geological
structure is present. The strike direction may be
defined as the direction of the trace of the
intersection between the bedding plane
Strike and Dip
 Strike and Dip
• Dip literally means slope or inclination. In
structural geology dip is expressed both as
direction and amount. The dip direction is the
direction along which the inclination of the
bedding plane occurs.
Strike and Dip
 Folds

• Folds are one of the most common geological

structures found in rocks. When a set of
horizontal layers are subjected to
compressive forces, they bend either
upward or downward. The bend noticed in
rocks are called folds.
• In terms of their nature too, folds may occur
as single local bends or may occur repeatedly
and intricately folded to the tectonic history
of the region.
Folds
Folds
 Classification and Types of Folds
Usually, folds are classified on the basis of
• Symmetrical Character
• Upward or Downward Bend
• Occurrence of Plunge
• Uniformity of Bed Thickness
• Behavior of the Fold Pattern with Depth.
Classification and Types of Folds
Anticline and Syncline
• When the beds are bent upwards, the resulting
fold is called anticline. This fold is convex
upwards. Naturally, in such a fold, the older
beds occur towards the concave side, In a
simple case, the limbs of anticline slope in
opposite directions with reference to its axial
plane. But when the anticline is refolded, the
inclined character of limbs will be complicated.
 Anticline and Syncline
• Syncline is just opposite to anticline in its nature,
i.e. when the beds are bent downwards the
resulting fold is called syncline. This fold is convex
downwards. In this the younger beds occur towards
the concave side and, in a simple type of syncline, its
limbs dip towards each other with reference to the
axial plane.
Anticline and Syncline
Anticline and Syncline
Classification and Types of Folds
Symmetrical and Asymmetrical Folds
• When the axial plane divides a fold into two
equal halves in such a way that one half is the
mirror image, then the fold is called as
symmetrical fold. If the compressive forces
responsible for folding are not of the same
magnitude, asymmetrical folds are formed.
Symmetrical and Asymmetrical folds
Classification and Types of Folds
Plunging and Non-Plunging Folds
• The plunge of a fold has already been described
as the inclination of the fold axis to the horizontal
plane. Based on this, i.e. whether the axis of a
fold is inclined or horizontal, the folds are
grouped as plunging folds or non-plunging
folds.
• In geological maps, when strike lines are drawn
for both the limbs, for a non-plunging fold, they
will be mutually parallel and for a plunging
fold they will be either converging or diverging
but not parallel.
Classification and Types of Folds
Plunging and Non-Plunging Folds
Classification and Types of Folds
Open and Closed Folds
• Depending on the intensity of deformation, the
beds of the fold may or may not have uniform
thickness. If the thickness of beds is uniform
throughout the folds, it is called an open
fold. On the other hand, in a fold, if the beds
are thinner in the limb portions and thicker
at crest and trough, such a fold is called
closed fold.
Classification and Types of Folds
Classification and Types of Folds
Similar and Parallel Folds
• Based on whether the shape of folds remain the
same or altered with depth, folds are grouped
as similar or parallel folds. In the case of similar
folds, the shape or pattern of folds remain the
same at depths also. But in the case of parallel
folds, the crest and trough become pointed or
angular
Classification and Types of Folds
Miscellaneous Folds
Overturned Fold
• Usually, in simple folds, the limbs show the
order of superposition. But when one of the
limb is overturned, the order of superposition
of beds in that limb will be in reverse order and
such a fold is called an overturned fold.
Overturned Fold
Classification and Types of Folds
Classification and Types of Folds
• Cheveron folds: Usually the crest and troughs
of beds are smoothly curved. But some folds
have sharply bent, angular crest and
troughs, such folds are known as “ Chevron
folds”.
Cheveron Folds
Classification and Types of Folds
Isoclinal Folds
• Usually the folds have inclined limbs, i.e. the
limbs will be mutually diverging or converging
with reference to axial planes. But in some
folds, the limbs will be mutually parallel to a
great extent. Such folds are called isoclinals
folds. These folds may be vertical inclined or
horizontal.
Classification and Types of Folds
Classification and Types of Folds
Fan Folds
• Usually in simple anticlines, the limbs dip away
from one another and in simple synclines they dip
towards each other. But in the case of fan folds,
this trend is just the opposite, i.e. in anticlines of
fan folds, the limbs dip towards each other
with reference to their axial plane. In synclines
of this kind, the limbs dip away from each
other. As the term suggests, these folds are fan
shaped.
Classification and Types of Folds
Classification and Types of Folds
Domes and Basins
• Usually, a fold will have two distinct limbs. But
some folds do not have any such specific limbs
and appear as beds locally pushed up or down,
i.e. their shapes appear as dome or basin. In a
dome, which resembles an upper hemisphere, the
dips are found in all sides from the common
central top point. Thus, this is a type of
anticline. In the basin, which is like a bowl, the
slopes are just opposite
Domes and Basins
Domes
Basins
 Classification and Types of Folds
Geanticlines and Geosynclines
• The anticlines and synclines with a normal
shape but a very large magnitude are called
Geanticlines and Geosynclines.
Geanticlines and Geosynclines
Classification and Types of Folds
Drag Folds
• These are the minor asymmetrical folds within
major folds but confined only to incompetent
beds which are sandwiched between competent
formations. These develop because of the
shearing/ dragging effect.
Drag Folds
 Mechanisms of Folding
• Folding of rocks takes place by different ways of
accommodation of stress. In many cases, slips or shear
occur in between the beds.
• The process is similar to slipping of cards which occurs
when the set is fold. If they are not allowed to slip over
one another, folding of the set cannot take place.
• This is the way in which folding generally occur in the
case of hard and competent rock like quartzites.
• In another kind of folding, folds are characterized by
thinning of the limbs and thickening of crest and
troughs. This takes place commonly in weak and
incompetent rocks like shales.
Mechanisms of Folding
Mechanisms of Folding
Mechanisms of Folding
 Causes and Effects of Folding
• Most of the important folds, as already pointed
out, are due to tectonic causes. But a few folds of a
minor type are due to non-tectonic causes,
• Mainly, the compressive and shear type of tectonic
forces are responsible for the folding
phenomenon. Igneous intrusion of viscous
magmas such as laccoliths and lopoliths also
contribute to folding.
• Non-tectonic causes like
landslides, creeping, differential
compaction, isostatic setting and glaciations too are
responsible for some folds. These are minor in
terms of frequency of occurrence and magnitude.
Causes and Effects of Folding
 Causes and Effects of Folding
• When a folded area is affected by weathering and
erosion, interesting topographic features are
produced as follows, immediately after folding,
anticlines by virtue of their upward bending appear
as hills and synclines due to downward warping
appear as valley. During folding in the crest
portions, the geological formation are subjected to
tensional forces and hence numerous fractures
appear there. Because of these fractures, crest
portions are eroded quickly leading to conspicuous
degradations locally.
 Causes and Effects of Folding
• On the other hand, trough portion are highly
compressed and hence offer a greater resistance to
erosion. Thus, they stand out in the long run at a
greater elevation, while the adjacent parts degrade
fast. The net result of this response to erosion is
that the anticlines will change over to valleys, while
synclines change 'over to hills.. This paradoxical
phenomenon is popularly expressed as “anticlinal
valleys and Synclinal hills” The anticlinal valley are
the typical example of inliers and the synclinal hill
are example of outlier.
 Faults
• From the Civil engineering point of view, faults are the most
unfavorable and undesirable geological structures at the site
for any given purpose, i.e. for location of reservoir; as
foundations site for construction of dams, importance
bridges or huge buildings, for tunneling; for laying roads,
railways tracks, etc.
• This is because faults considerably weaken the rocks and
render the sites in which they occur as unfavorable places for
all constructional purposes.
• Further, as long as the faults are active, the site is unstable
and susceptible to upward, downward or sideward movement
along the fault plane, thereby making the places highly
hazardous for foundation purposes. Thus, by virtue of the
harm they are capable of causing, faults are necessarily
investigated with special care in dealing with any major
construction.
Faults
Faults
 Joints and Faults
• Structurally, faults may be described as fractures
along which relative displacement of adjacent
blocks has taken place.
• If such relative displacement does not take place
on either side of fracture plane, it is called a joint.
Thus both joint and faults are fractures in rocks
but with difference in the kind of displacement.
Joints may be described as a set of aligned parallel
cracks or openings in geological formations.
Joints and Faults
 Magnitude of Faults
• Like folds, faults also have considerable range in their
magnitude. Some occur for short distance, while
other can be traced for very long distances. In some
cases displacement may be less than a centimeter
while in other it may be many or even kilometers.
The magnitude of faulting obviously depend on the
intensity and the nature of shearing stresses involved.
Magnitude of Faults
 Nature of Fault Plane
• Rarely the displacement during faulting occurs
along a single fault plane. In many cases,
faulting takes place along a number of parallel
fractures, Such a zone which contains a number
of closely spaced sub-parallel fractures along
which the relative displacement has taken place is
called shear zone or fault zone.
• A fault plane may be plain or straight or may
be curved or irregular, it may be horizontal or
inclined or vertical.
Nature of Fault Plane
 Recurrence of Faulting
• Faulting occurs when shearing resistance of the
geological formation is overcome by the tectonics
forces. Occurrence of faulting is often accompanied by
earthquakes and it is an indication of subsurface
instability of the region concerned.
• Thus, faulting may be treated as an attempt to reach
stability. Because of the hard, rigid and solid nature of
the rock masses involved, this stability is not achieved in
one stroke but by repetition of the process. Thus once if
a faulting occur in a place, it shall remain active for
some time, i.e. subsequent recurring faulting takes place
there only.
 Recurrence of Faulting
• This is so because this fault plane offers the
least resistance for the readjustment of the
blocks concerned and for the release of
accumulated energy in the rock. Once the
stability is attained, faulting may not recur
or, even if faulting takes place, it would be of
mild intensity. Such faults which have not
been affected in the known histgory are called
dead faults.
 Parts of a Fault
• The different parts of a fault are
Fault Plane
• This is the plane along which the adjacent blocks
were relatively displaced. In other words, this is the
fracture surface on either side of which the rocks
had moved past one another. Its intersection with
the horizontal plane gives the strike direction of the
fault. The direction along which the fault plane has
the maximum slope is its true dip direction.
Parts of a Fault
 Parts of a Fault
Foot Wall and Hanging Wall
• When the fault plane is inclined, the faulted
block which lies below the fault plane is called
the “foot wall” and the other block which rests
above the fault plane is called “hanging wall”.
In this case of vertical faults, naturally the
faulted blocks cannot be described as foot wall
or hanging wall.
Foot Wall and Hanging Wall
 Parts of a Fault
Slip
• The displacement that occurs during faulting is
called the slip. The total displacement is known as
the next slip. This may be along the strike direction or
the dip direction or along both.
 Parts of a Fault
Heave and Throw
• The horizontal component of displacement
is called “heave” and the vertical component
of displacement is called “throw”
• In vertical faults, there is only throw, but no
heave. In horizontal faults, there is only heave,
but no throw.
Heave and Throw
Classification and Types of Faults
• Like folds, faults also have been classified on
the basis of different principles as
• Types of displacement along the plane.
• Relative movement of foot wall and hanging
wall.
• Types of slip involved.
• Mode of occurrence of faults
Classification and Types of Faults
Types of displacement along the plane
• Based on this principle, faults are divisible into
transitional faults and rotational faults.
• In the case of transitional faults, the type of
displacement of the foot wall with reference to
the hanging wall is uniform along the fault
plane.
• In the case of the rotational fault the
displacement varies from place to place.
Classification and Types of Faults
• Relative movement of the footwall and the
Hanging Wall.
• In the case of inclined faults, if the hanging
wall goes down with reference to the footwall,
it is called normal fault or Gravity fault.
These terms are very appropriate because of
the hanging wall is normally expected to move
down along the slope of the fault plane under
the influence of gravity.
Classification and Types of Faults
Classification and Types of Faults
• If the kind of displacement of the hanging wall is
opposite to this, the fault is called Reverse faults
or thrust fault. These terms also are appropriate
because in such fault plane and, therefore the type
of displacement is the reverse of the normally
expected downward movement of the hanging
wall under such a condition.
• If the relative displacement of the hanging wall is
neither upwards nor downwards with reference to
the inclined fault plane, but sidewards, then such
faults are described as Sinstral Faults.
Classification and Types of Faults
Classification and Types of Faults
Types of Slip Involved
• Slip has been already described as the
displacement along the fault plane. If the
displacement is along the strike direction of
the fault plane, such a fault is described as
strike slip fault. On the other hand. If the
displacement occurs partly along the strike
direction of the fault plane, such a fault is
called an oblique slip fault.
Strike Slip Fault
Oblique Slip Fault
Classification and Types of Faults
Classification and Types of Faults
Mode of Occurrence
Radial Faults
• When a set of faults occur on the surface and appears to be
radiating from a common point, they are called radial
faults.
Enechelon Faults
• These refer to a series of minor faults which appear to be
overlapping one another.
Arculate or Peripheral Faults
• These also refers to a set of relatively minor faults which
have curved outcrop and are arranged in a peripheral
manner, enclosing more or less a circular area.
Classification and Types of Faults
Classification and Types of Faults
Miscellaneous
Step Faults
• When a set of parallel normal faults occur at a
regular interval, they give a step-like
appearance and are called step faults.
Parallel Faults
• As the name indicates, these are a set of
parallel normal faults with the same strike and
dip. They are like step faults but may or may
not have a regular interval.
Classification and Types of Faults
Horst and Grabens
• When normal faults with mutually diverging or
converging fault plane occurs, then a few
wedge-shaped blocks called “horst” are
displaced upwards and a few other called
“grabens” are displaced downwards.
Horst and Grabens of large magnitude are
called block mountain and rift valleys.
Step Faults
Parallel Faults
Classification and Types of Faults
 Causes of Faulting
• Faults may occur due to various causes, among them
tectonic causes are responsible not only for most of the
faults but also for faults of grater magnitude.
• It may be recollected that faults develop mainly due to
shear and sliding failures resulting from tectonic forces. It
is natural that compression and tensional forces be mutually
interlinked because if in one part of the crust there is
compression, in the adjacent part there will be tension.
• In addition to these main causes, sometimes, the formation
of magmatic intrusions such as bysmaliths, may also
contribute to faulting, though on a very small scale.
Occasionally, local settlement under the influence of
gravity may also cause minor faulting.
Causes of Faulting
 Effects of Faulting
• The faulting phenomenon produces dislocation in
lithology and topography. Hence, they offer evidences
to recognize faults in the field. Proper geological
investigation followed by geological mapping
enables one to detect the occurrence of faults in any
area.
• Slickness, fault drags, brecciation, mineralization
zones, repetition and omission of strata and offsets of
beds are some of the lithological evidences of Faulting.
• Topographical evidences include various surface
features like, offset ridges, parallel deflection of
valley, reversal of drainage, straight reverse courses,
and a straight and steep coastal lines.
Effects of Faulting
 Joints
• Joints are fractures found in all types of
rocks. They are cracks or openings formed
due to various reasons. Naturally, the
presence of joints divides the rock into number
of parts or blocks. In simple terms, through
the joints may be described as mere cracks
in rocks, they differ mutually. Joints, like
cleavages of minerals, occur oriented in a
definite direction and as a set.
Joints
Joints
 Joints
Effects of Joints
• From the civil engineering point of view, joints
are important because they split the rocks into
a number of pieces which, in turn, reduce
the competence of rock mass, increase the
porosity and permeability and make them
susceptible to quick decay and weathering.
• Joints But a few advantages that accompany
joints are; their occurrence increases the
ground water potential in any place.
Joints
 Joints
• Joints, though they resembles faults by appearing
as fractures in rocks, are not as dangerous as
faults. This is so primarily because the region
affected by joint are not liable to recurrence of
joints in future as happens in the case of faults.
Thus places where joints occur are not very
unstable for foundation purpose. Also the area
affected by joints can be easily improved by
methods such as suitable cement grouting or
plugging.
 Joints
Parts of a Joint
• Joints like faults, refer to the fracture in rocks.
Hence, like faults, inclined and vertical joints
also can be described by their attitude.
• However, in joints the fracturing blocks are not
named as footwall or hanging wall.
 Joints
Classification of Joints
• Classification based on the relative attitude of
joints
• When the joints are parallel to the strike and
dip of adjacent beds, they are called Strike
Joints or Dip Joints, respectively.
• If the strike direction of joints is parallel neither
to the strike nor dip direction of adjacent
beds, then such joints are called Oblique
Joints.
• If the strike direction, dip direction and dip
amount) coincides completely with the attitude of
adjacent beds, they are called bedding joints.
 Joints
Classification based on the Origin of Joints
• Most of the joints are formed due to either
tensional forces or shearing forces.
Accordingly they are described as Tension or
Shear Joint.
Classification of Joints
 Unconformities
• Unconformity is one of the common
geological structure found in rocks. It is
somewhat different from other structures like
folds, faults and joints in which the rock are
distorted, deformed or dislocated at a
particular place. Still, unconformity is a
product of diastorphism and involve
tectonic activity in the form of upliftment
and subsidence of land mass.
Unconformities
 Unconformities
• When a sedimentary rocks are formed
continuously or regularly one after another
without any major brake, they are said to be
conformable beds, and this phenomenon is called
conformity. All the beds belonging to
conformable set shall possess the shame strike
direction, dip direction and dip amount.
• On the other hand, if a major break occurs in
sedimentation in between two sets of
conformable beds, it is called an unconformity.
 Parts of an Unconformity
• There are different types of unconformities, all
the types have two different ages, i.e. one set is
older and the other set is younger having a
depositional break in between)
Unconformity
 Unconformity
Hiatus
• An unconformity which represent a long
geological period during which break in
sedimentation had occurred) is known as a
“hiatus”.
Hiatus
 Types of an Unconformity
Types of Unconformities
• Based on factors such as type of rocks, relative
attitude of sets involved and their extent of
occurrence, the different types of unconformities
are named as
Non-Conformity
• When the underlying older formation are
represented by igneous or metamorphic rocks
and the overlying younger formation are
sedimentary rocks, the unconformity is called
“non-conformity”
Types of an Unconformity
 Types of an Unconformity
Angular Unconformity
• When the younger bed and older set of
strata are not mutually parallel, then the
unconformity is called “angular
unconformity”. In such a case, beds of one set
occur with a greater tilt or folding.
 Types of an Unconformity
Disconformities
• On the other hand, if the bed of the younger
and older set are mutually parallel and the
contact plane of two sets is only an erosion
surface, then the unconformity is called
“disconformities” in this case, the lower set of
beds have undergone denudation before the
deposition of the overlying strata commenced.
 Types of an Unconformity
Paraconformity
• When the two sets of beds are parallel and
the contact is a simple bedding plane, the
unconformity is called “paraconformity”. In
such cases, the unconformities is inferred by
features like sudden change in fossil content
or in lithological nature.
Types of an Unconformity
 Types of an Unconformity
Regional and Local Unconformities
• When an unconformity extends over a larger
or over a greater area, it if called regional
unconformity. On the otherhand, if an
unconformity occur over a relatively small
area it is called local unconformity.
 Unconformity
Recognition of Unconformities
• Some of the evidences which helps in the recognition of
unconformity are:
• Difference in attitude of two adjacent sets of beds
• Remarkable difference in nature, age and types of beds.
• Occurrence of residual soil/ laterite/bauxite along the
unconformity surface.
• Considerable difference in the degree of metamorphism of
two adjacent sets of beds.
• Stratification correlation and lithological pecularities.
• All of these and other evidences are inherently linked up
with the processes of unconformity formation
Recognition of Unconformities
 References

• Engineering and General Geology : By Parbin Singh

• Textbook of Engineering Geology : N.Chenna
Kesavullu
• http://geology.com/
Thanks !

Brittle Deformation