Mach3 USB Motion Card STB4100 V2.
1
Mach3 USB Motion Card (STB4100) Installation Manual
V2.1
Mach3 USB Motion Card STB4100 V2.1
The motion control card for machine control, with
strong professional.Requires the operator to have the
relevant expertise!If used improperly, may appear an
accident, please strictly follow the instructions and warnings using this
product if you are not sure, consulting engineers for help.First time
users, if you are not familiar with the product and software features
Mach3 In your test product, make sure the machine's power switch on
hand, you can quickly turn off the power. Recommends that users
install the emergency stop button and make sure the button is
functioning properly. Please strictly follow the instructions and
warnings using this product.Any direct / indirect personal injury, our
company does not assume any responsibility.
Mach3 USB Motion Card STB4100 V2.1
Contents
Mach3 USB Motion Card (STB4100) Installation
Manual......................................................... 1
Contents ..........................................................................
........................................................ 3
Features:..........................................................................
........................................................ 4
Basic connection diagram (an
Overview):.........................................................................
....... 5
Mechanical dimensions
diagram: ..........................................................................
.................. 6
1.Prepare: ........................................................................
........................................................ 6
1.1.Installation the
Mach3:.............................................................................
..................... 6
1.2.Software license
application:.......................................................................
.................. 7
1.3. Installation the software of the USB motion
card:........................................................ 7
1.3.1 Connecting the USB cable to the PC and the motion
card: ..................................... 7
1.3.2 Installing the motion card plug-
in. .......................................................................... 8
2.config for
mach3:.............................................................................
..................................... 9
2.1 Mach3 X、 Y、 Z、 A Axis config as shown below: Config => Ports and
Pins): .......... 9
2.2 Motor tuning setup as shown below: (Config => Motor
Tuning) ................................. 10
2.3 The Mach3 Menu => Config => Homing/Limits dialog：
............................................. 10
2.4 Setup the input signal：
...................................................................................
......... 10
2.5 Setup the Output
signals:...........................................................................
.................. 11
2.6 Spindle speed control (0-10V)
Setup:...........................................................................
12
2.6 Mach3 MPG
Setup: ............................................................................
.......................... 14
Mach3 USB Motion Card STB4100 V2.1
Features:
1. Support for 4-axis linkage, you can connect four stepper motor drives or servo
drives;
2. Maximum step-pulse frequency is 100KHz,which is suitable for the servo or
stepping motor;
3. 4 general-purpose opto-couplers isolation input : can connect the limit switch,
emergency stop
switch, auto tool zero, home switch etc.
4. Support for connecting electronic handwheel;
5. Have 0-10V signal output , you can use mach3 software to control the spindle
motor speed.
6. 4 general-purpose isolated relay drive output interface, can drive four relays
for controlling
the spindle starts, forward rotating and reverse rotating, pumps or other device;
7. 1 status LED, indicate connection status on the board.
Mach3 USB Motion Card STB4100 V2.1
Basic connection diagram (an Overview):
Mach3 USB Motion Card STB4100 V2.1
Mechanical dimensions diagram:
1.Prepare:
1.1.Installation the Mach3:
Open the CD, find mach3 software，run the installation file：
Follow the prompts to install, until the last step.
The last step requires Note: For 64-bit computer, it is best not to
select”LoadMach3 Driver “this
one, because it will cause the system to prompt installation errors.
Mach3 USB Motion Card STB4100 V2.1
1.2.Software license application:
Copy license files “Mach1Lic.dat” from “mach3 software folder”,to C:\Mach3 Cover
the
original file,Reset Computer（must reset the computr,please don't open the software
dircetly!）
Way above the license for DIY or study purposes only, not for commercial use.
1.3. Installation the software of the USB motion card:
This USB motion card does not need install any USB
driver,Windows2000/XP/Windows7,can
directly identify.
1.3.1 Connecting the USB cable to the PC and the motion card:
The first installation of motion control card, take about 10s, when the green led
lights on motion
control card, indicating that the connection is successful, return the following
tips when you
install on your computer:
1 2
Mach3 USB Motion Card STB4100 V2.1
1.3.2 Installing the motion card plug-in.
Unzip the usb move.zip, copy or drag RnRMotion.dll into your Mach3\PlugIns folder.
1.3.3 Start the Mach3 software, a dialogue of “Motion Control Hardware PlugIn
sensed!” is
shown. Please select the“ RnRMotionControllerECO-V2.0”, you can also check”Don't
ask me
this again”.
Mach3 USB Motion Card STB4100 V2.1
2.config for mach3:
2.1 Mach3 X、 Y、 Z、 A Axis config as shown below: Config => Ports
and Pins):
Pick tick “√”
Suggest to put ticks”√ ”,
to set low signal levels
actived
After setting, click "Apply" to
save the setting results
Mach3 USB Motion Card STB4100 V2.1
2.2 Motor tuning setup as shown below: (Config => Motor Tuning)
2.3 The Mach3 Menu => Config => Homing/Limits dialog：
Axis direction, depends on the “Reversed”
2.4 Setup the input signal：
There are 4 general-purpose input channels. The channels number is from I1 to I4.
Example of input signal settings: I1 is connected to emergency stop switch, I2 is
connected to 4 axis
limit switches, I3 is connected to 4 axis home switches, I4 is connected to auto
tool zero, set as shown
Setup each axis
