AMERICAN

BUILDING
® COMPONENTS

26 Gauge Panel Product Information

Effective April 10, 2006

This booklet includes:

Trims and Accessories Information For
"PBR", "PBU" and 5-V Crimp 26 Gauge Panels
 Sgiven
ince 1908, our large selection of Panels and Trim have
buildings the finished look throughout America.
American Building Components wants your building to
give you years of beauty and reliability. Please take time to
read the following important information on safety and the
care of our roofing and siding materials.

SAFETY PRECAUTIONS
Improper unloading and handling of bundles Use extreme care when walking, sitting,
and crates may cause bodily injury or material standing or kneeling on a metal roof to avoid a fall.
damage. Use extreme care in the operation of Galvalume and galvanized panels have a light
power lifting devices, such as cranes and forklifts, coating of oil to protect the panels from moisture
and follow the safety instructions provided by their prior to erection. They can be extremely slippery, as
manufacturer. Crates, boxes and bundles may be are painted panels when they are wet. If necessary,
bulky, heavy or both. The improper or unaided remove the oil coating with a non-abrasive
lifting of them may cause bodily injury. The detergent and water mixture followed by a clear
manufacturer is not responsible for bodily injuries or water rinse. Insure the panels are dry prior to
material damage due to improper handling during installation.
unloading, storage or job-site placement. When nails are used to fasten the panels,
Protective heavy duty gloves should be worn goggles should be worn to prevent possible eye
when handling metal panels and trim products. injuries. Off center strikes by the hammer may
Safety goggles or face shield should be worn while cause nails to ricochet or metal fragments to
cutting or drilling metal products with power tools. become dislodged, striking the user or those
Follow the safety instructions provided by the nearby. Insure adequate safety measures and
manufacturer of the power tools. warnings are in place and followed.

STORAGE AND HANDLING

To preserve and protect the attractive Prolonged storage of sheets in bundles is not
appearance of American Building Components’ recommended. If conditions do not permit
roofing and siding from damage caused by immediate erection, extra care must be taken to
moisture, corrosive chemicals or improper handling, protect the material from damage caused by
it is necessary that you take a few simple moisture.
precautions. When material is received bundled, Store bundled sheets ONLY IN A DRY PLACE.
panels should be inspected for moisture. If there is Sheets should be unbundled, stood on end against
moisture, the panels should be separated and an interior wall to allow for air circulation. If unable to
dried. If shipping damage is found, the carrier store sheets in an upright position, strapping bands
should be advised and a notation made on the bill should be broken and sheets should be blocked off
of lading. the floor with one end slightly elevated.
On job sites, reasonable care should be taken Stacked sheets should then be completely protected
when handling painted surfaces during installation from the elements while maintaining good air flow to
in order to protect the finish. Although the paint prevent condensation. A properly draped canvas
coating is tough and provides impact resistance, tarpaulin that allows air flow is an example of a good
dragging panels across the surface of one another protective cover. Do not use plastic, as it causes
will almost certainly mar the finish. sweating or condensation to occur.

AMERICAN
BUILDING
® COMPONENTS
© Copyright American Building Components 2006. All Rights Reserved.

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-2 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 ITEM PAGE

PANEL PRICING INFORMATION 3

''PBR" • "PBU" • 5V Crimp PANEL INFORMATION 4-6
26 GAUGE SQUARE FOOT CHART FOR - "PBR" & "PBU" 7
26 GAUGE SQUARE FOOT CHART FOR - "5V-CRIMP" 8
PANEL TRIM 9-16
5V-CRIMP TRIM 17
PANEL ACCESSORIES 18-21
VENT MATERIAL 21-22
TERMS AND CONDITIONS OF SALE 23
HOW TO ORDER SPECIAL FLASHING 24
COLOR CHART 25
NOTES 26-27

PANEL PRICING:
1. All "PBR" and "PBU" Panel prices are based on 38 1/4" sheet width (see chart page 7).
2. Add $.75 per sheet for lengths under 4' - 0".

PACKAGING COST:
1. Maximum 3,000 Ibs. per bundle.
2. Block and band only $9.00
3. Block and band, water proof paper wrap $12.75 (up to 15' 0") $22.85 (over 15')
4. Block and band, waste sheet top only $14.42 (up to 15' 0") $28.02 (over 15')
5. Block and band, waste sheet top and bottom $28.02 (up to 15' 0") $51.76 (over 15')

FREIGHT:
FREIGHT: All prices are F.O.B. shipping point. • Stopover charge (For unloading delay in excess of
1 1/2 hours, charged in 1/2 hour increments). $90.00 Per Hour
FREIGHT CHARGES: 1-1/2% of invoice. Freight • Minimum charge for deliveries under $250.00 in value
on LTL shipments will be charged at the applicable or applicable freight charges, whichever is less. $25.00
commercial rate. • Job Site Delivery $75.00 MINIMUM
• Drop Charge $25.00

NOTICE:
ABC is pleased to provide job site delivery to our customers. Customers requesting this service must have mechanized means to offload the
material (i.e.- crane, forklift, gin pole). The job site location must be accessible to a vehicle 65' long and weighing up to 80,000 pounds. ABC
reserves the right to refuse delivery at job sites where unsafe or impassable terrain or road conditions are present.

TERMS:
Invoices paid ABC by buyer within 10 days of date of shipment are allowed 1/2% of 1% discount, net due 30 days from date of
shipment. Orders paid before shipment will be given discount; C.O.D. shipments paid at time of shipment are not allowed discount.
Possession of this price sheet does not constitute a proposal to sell. Prices in effect at time of shipment will apply.

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-3
 26 GAUGE “PBR” PANEL INFORMATION

“PBR” PANEL
36"
12" 1" 3/4"
3
/16"
1 1/4"
3 5/64" 13/8"
4" 4" 4"

SECTION PROPERTIES

PANEL Fy WEIGHT
TOP FLAT IN COMPRESSION BOTTOM FLAT IN COMPRESSION
GAUGE (KSI) (PSF) IX SX Ma IX SX Ma
(in.4/ft.) (in.3/ft.) (in. Kip) (in.4/ft.) (in.3/ft.) (in. Kip)

26 80.0 0.94 0.0423 0.0388 1.3928 0.0390 0.0437 1.5698

NOTES
1. All calculations for the properties of panels are calculated in accordance with the 1986 edition of Specifications for
the Design of Light Gauge Cold Formed Steel Structural Members - published by the American Iron and Steel
Institutue (A.I.S.I.)
2. Ix is for deflection determination.
3. Sx is for bending.
4. Ma is allowable bending moment.
5. All values are for one foot of panel width.

ALLOWABLE UNIFORM LIVE LOADS IN POUNDS PER SQUARE FOOT

SPAN LOAD 26 GAUGE (Fy = 80 KSI)
TYPE TYPE SPAN IN FEET
3.0 4.0 5.0 6.0 7.0 8.0
SIMPLE NEGATIVE WIND LOAD 155.0 87.2 55.8 38.8 28.5 21.8
LIVE LOAD/DEFLECTION 102.7 43.3 22.2 12.8 8.1 5.4
2-SPAN NEGATIVE WIND LOAD 137.6 77.4 49.5 34.4 25.3 19.3
LIVE LOAD/DEFLECTION 116.3 65.4 41.9 28.5 18.0 12.0
3-SPAN NEGATIVE WIND LOAD 172.0 96.7 61.9 43.0 31.6 24.2
LIVE LOAD/DEFLECTION 145.4 75.4 38.6 22.3 14.1 9.4
4-SPAN NEGATIVE WIND LOAD 160.6 90.3 57.8 40.1 29.5 22.6
OR MORE LIVE LOAD/DEFLECTION 135.7 76.3 41.0 23.7 14.9 10.0

NOTES
1. Allowable loads are based on uniform span lengths and Fy of 80 KSI for 26 gauge.
2. LL is allowable live load.
3. WL is allowable wind load and has been increased by 33.333%.
4. Deflection loads are limited by a maximum deflection ratio of L/240 of span or maximum bending stress to live
load.
5. Weight of the panels has not been deducted from allowable loads.
6. Load table values do not address web crippling requirements or connection of panel to substrate.
7. Minimum bearing length of 1.5" required.

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-4 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE “PBU” PANEL INFORMATION

“PBU” PANEL
36"
6" 1"
3/4"

2 1/2" 3 1/2"

SECTION PROPERTIES

PANEL Fy WEIGHT
TOP FLAT IN COMPRESSION BOTTOM FLAT IN COMPRESSION
GAUGE (KSI) (PSF) IX SX Ma IX SX Ma
(in.4/ft.) (in.3/ft.) (in. Kip) (in.4/ft.) (in.3/ft.) (in. Kip)

26 80.0 0.94 0.0262 0.0434 1.5610 0.0180 0.0409 1.4710

NOTES
1. All calculations for the properties of panels are calculated in accordance with the 1986 edition of Specifications for
the Design of Light Gauge Cold Formed Steel Structural Members - published by the American Iron and Steel
Institutue (A.I.S.I.)
2. Ix is for deflection determination.
3. Sx is for bending.
4. Ma is allowable bending moment.
5. All values are for one foot of panel width.

ALLOWABLE UNIFORM LIVE LOADS IN POUNDS PER SQUARE FOOT

SPAN LOAD 26 GAUGE (Fy = 80 KSI)
TYPE TYPE SPAN IN FEET
3.0 4.0 5.0 6.0 7.0 8.0
SIMPLE NEGATIVE WIND LOAD 145.3 81.7 52.3 36.3 26.7 20.4
LIVE LOAD/DEFLECTION 63.6 26.8 13.7 8.0 5.0 3.4
2-SPAN NEGATIVE WIND LOAD 154.2 86.7 55.5 38.5 28.3 21.7
LIVE LOAD/DEFLECTION 105.3 44.4 22.7 13.2 8.3 5.6
3-SPAN NEGATIVE WIND LOAD 192.7 108.4 69.4 48.2 35.4 27.1
LIVE LOAD/DEFLECTION 82.5 34.8 17.8 10.3 6.5 4.3
4-SPAN NEGATIVE WIND LOAD 179.9 101.2 64.8 45.0 33.1 25.3
OR MORE LIVE LOAD/DEFLECTION 87.5 36.9 18.9 10.9 6.9 4.6
NOTES
1. Allowable loads are based on uniform span lengths and Fy of 80 KSI for 26 gauge.
2. LL is allowable live load.
3. WL is allowable wind load and has been increased by 33.333%.
4. Deflection loads are limited by a maximum deflection ratio of L/240 of span or maximum bending stress to live
load.
5. Weight of the panels has not been deducted from allowable loads.
6. Load table values do not address web crippling requirements or connection of panel to substrate.
7. Minimum bearing length of 1.5" required.

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-5
 26 GAUGE 5V CRIMP-26 PANEL INFORMATION

5V Crimp
24"
12"
1/2"

5V CRIMP
SECTION PROPERTIES
NEGATIVE BENDING POSITIVE BENDING
PANEL Fy WEIGHT Ixe Sxe Maxo Ixe Sxe Maxo
GAUGE (KSI) (PSF) (IN.4/FT.) (IN.3/FT.) (KIP-IN.) (IN.4/FT.) (IN.3/FT.) (KIP-IN.)
29 60* 0.75 0.0014 0.0074 0.2662 0.0028 0.0061 0.2204
26 60* 0.95 0.0018 0.0112 0.4018 0.0032 0.0079 0.2826
* Fy is 80 ksi reduced to 60 ksi in acco rdance with the 2001editio n o f the N o rt h A m e ric a n S pe c if ic a t io n F o r D e s ign o f C o ld- F o rm e d S t e e l S t ruc t ura l M e m be rs - A 2.3.2.
NOTES:
1. All calculations for the properties of 5V Crimp panels are calculated in accordance w ith the 2001 edition of the North American Specification
For Design of Cold-Formed Steel Structural M embers.
2. Ixe is for deflection determination.
3. Sxe is for Bending.
4. Maxo is allow able bending moment.
5. All values are for the one foot of panel w idth.
29 Gauge ALLOWABLE UNIFORM LOADS IN POUNDS PER SQUARE FOOT
( F y = 6 0 k s i) SPAN IN FEET
SPAN TYPE LOAD TYPE 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Negative Wind Load 177.5 78.9 44.4 28.4 19.7 14.5 11.1
SINGLE
Live Load/Deflection 146.9 65.3 30.2 15.4 8.9 5.6 3.8
Negative Wind Load 146.9 65.3 36.7 23.5 16.3 12.0 9.2
2 SPAN
Live Load/Deflection 142.1 64.3 36.4 23.4 16.3 12.0 9.1
Negative Wind Load 183.7 81.6 45.9 29.4 20.4 15.0 11.5
3 SPAN
Live Load/Deflection 172.5 79.9 45.4 29.1 16.9 10.6 7.1
Negative Wind Load 171.5 76.2 42.9 27.4 19.1 14.0 10.7
4 SPAN
Live Load/Deflection 164.4 74.8 42.4 27.2 17.9 11.3 7.6

26 Gauge ALLOWABLE UNIFORM LOADS IN POUNDS PER SQUARE FOOT

( F y = 6 0 k s i) SPAN IN FEET
SPAN TYPE LOAD TYPE 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Negative Wind Load 267.9 119.1 67.0 42.9 29.8 21.9 16.7
SINGLE
Live Load/Deflection 188.4 83.4 35.2 18.0 10.4 6.6 4.4
Negative Wind Load 188.4 83.7 47.1 30.1 20.9 15.4 11.8
2 SPAN
Live Load/Deflection 182.4 82.5 46.7 30.0 20.9 15.3 10.6
Negative Wind Load 235.5 104.7 58.9 37.7 26.2 19.2 14.7
3 SPAN
Live Load/Deflection 224.9 102.5 58.2 34.0 19.7 12.4 8.3
Negative Wind Load 219.9 97.7 55.0 35.2 24.4 18.0 13.7
4 SPAN
Live Load/Deflection 211.0 95.9 54.4 34.9 20.9 13.2 8.8
NOTES:
1. Allow able loads are based on uniform span lengths and Fy = 60ksi.
2. LIVE LOAD is limited by bending, shear, combined shear & bending, or w eb crippling.
3. NEGATIVE WIND LOAD does not contain a 33.333% increase and does not consider fastener pullout or pullover.
4. Above loads consider a maximum deflection ratio of L/180.
5. The w eight of the panel has not been deducted from the allow able loads.
6. The use of any accessories other than those provided by the manufacturer may damage panels, void all w arranties and w ill void all engineering data.
7. This material is subject to change w ithout notice.
8. See w w w .am ericanbuildingcom ponents.com for most current information.

The Engineering data co ntained herein is fo r the expressed use o f custo mers and design pro fessio nals. A lo ng with this data, it is reco mmended that the design pro fessio nal have a co py o f
the mo st current versio n o f the N o rt h A m e ric a n S pe c if ic a t io n f o r t he D e s ign o f C o ld- F o rm e d S t e e l S t ruc t ura l M e m be rs published by the A m e ric a n Iro n a nd
S t e e l Ins t it ut e to facilitate design. This Specificatio n co ntains the design criteria fo r co ld-fo rmed steel co mpo nents. A lo ng with the Specificatio n, the designer sho uld reference the
mo st current building co de applicable to the pro ject jo bsite in o rder to determine enviro nmental lo ads. If further info rmatio n o r guidance regarding co ld-fo rmed design practices is desired,
please co ntact the manufacturer.
FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 26GA-6 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE SQUARE FOOT CHART

"PBR" Panel "PBU" Panel

36" 36"
12" 1" 6" 1"
3/4" 3/4"
3/16" 1-1/4"

2 1/2" 3 1/2"
4" 4" 4" 3 5/64" 1 3/8"

0" 1" 2" 3" 4" 5" 6" 7" 8" 9" 10" 11"

1 FT. 3.19 3.45 3.72 3.98 4.25 4.52 4.78 5.05 5.31 5.58 5.84 6.11
2 FT. 6.38 6.64 6.91 7.17 7.44 7.70 7.97 8.23 8.50 8.77 9.03 9.30
3 FT. 9.56 9.83 10.09 10.36 10.63 10.89 11.16 11.42 11.69 11.95 12.22 12.48
4 FT. 12.75 13.02 13.28 13.55 13.81 14.08 14.34 14.61 14.88 15.14 15.41 15.67
5 FT. 15.94 16.20 16.47 16.73 17.00 17.27 17.53 17.80 18.06 18.33 18.59 18.86

6 FT. 19.13 19.39 19.66 19.92 20.19 20.45 20.72 20.98 21.25 21.52 21.78 22.05
7 FT. 22.31 22.58 22.84 23.11 23.38 23.64 23.91 24.17 24.44 24.70 24.97 25.23
8 FT. 25.50 25.77 26.03 26.30 26.56 26.83 27.09 27.36 27.63 27.89 28.16 28.42
9 FT. 28.69 28.95 29.22 29.48 29.75 30.02 30.28 30.55 30.81 31.08 31.34 31.61
10 FT. 31.88 32.14 32.41 32.67 32.94 33.20 33.47 33.73 34.00 34.27 34.53 34.80

11 FT. 35.06 35.33 35.59 35.86 36.13 36.39 36.66 36.92 37.19 37.45 37.72 37.98
12 FT. 38.25 38.52 38.78 39.05 39.31 39.58 39.84 40.11 40.38 40.64 40.91 41.17
13 FT. 41.44 41.70 41.97 42.23 42.50 42.77 43.03 43.30 43.56 43.83 44.09 44.36
14 FT. 44.63 44.89 45.16 45.42 45.69 45.95 46.22 46.48 46.75 47.02 47.28 47.55
15 FT. 47.81 48.08 48.34 48.61 48.88 49.14 49.41 49.67 49.94 50.20 50.47 50.73

16 FT. 51.00 51.27 51.53 51.80 52.06 52.33 52.59 52.86 53.13 53.39 53.66 53.92
17 FT. 54.19 54.45 54.72 54.98 55.25 55.52 55.78 56.05 56.31 56.58 56.84 57.11
18 FT. 57.38 57.64 57.91 58.17 58.44 58.70 58.97 59.23 59.50 59.77 60.03 60.30
19 FT. 60.56 60.83 61.09 61.36 61.63 61.89 62.16 62.42 62.69 62.95 63.22 63.48
20 FT. 63.75 64.02 64.55 48.55 64.81 65.08 65.34 65.61 65.88 66.14 66.41 66.67

21 FT. 66.94 67.20 67.47 67.73 68.00 68.27 68.53 68.80 69.06 69.33 69.59 69.86
22 FT. 70.13 70.39 70.66 70.92 71.19 71.45 71.72 71.98 72.25 72.52 72.78 73.05
23 FT. 73.31 73.58 73.84 74.11 74.38 74.64 74.91 75.17 75.44 75.70 75.97 76.23
24 FT. 76.50 76.77 77.03 77.30 77.56 77.83 78.09 78.36 78.63 78.89 79.16 79.42
25 FT. 79.69 79.95 80.22 80.48 80.75 81.02 81.28 81.55 81.81 82.08 82.34 82.61

26 FT. 82.88 83.14 83.41 83.67 83.94 84.20 84.47 84.73 85.00 85.27 85.53 85.80
27 FT. 86.06 86.33 86.59 86.66 87.13 87.39 87.66 87.92 88.19 88.45 88.72 88.98
28 FT. 89.25 89.52 89.78 90.05 90.31 90.58 90.84 91.11 91.38 91.64 91.91 92.17
29 FT. 92.44 92.70 92.97 93.23 93.50 93.77 94.03 94.30 94.56 94.83 95.09 95.36
30 FT. 95.63 95.89 96.16 96.42 96.69 96.95 97.22 97.48 97.75 98.02 98.28 98.55

31 FT. 98.81 99.08 99.34 99.61 99.88 100.14 100.41 100.67 100.94 101.20 101.47 101.73
32 FT. 102.00 102.27 102.53 102.80 103.06 103.33 103.59 103.86 104.13 104.39 104.66 104.92
33 FT. 105.19 105.45 105.72 105.98 106.25 106.52 106.78 107.05 107.31 107.58 107.84 108.11
34 FT. 108.38 108.64 108.91 109.17 109.44 109.70 109.97 110.23 110.50 110.77 111.03 111.30
35 FT. 111.56 111.83 112.09 112.36 112.63 112.89 113.16 113.42 113.69 113.95 114.22 114.48

36 FT. 114.75 115.02 115.28 115.55 115.81 116.08 116.34 116.61 116.88 117.14 117.41 117.67
37 FT. 117.94 118.20 118.47 118.73 119.00 119.27 119.53 119.80 120.86 120.33 120.59 120.86
38 FT. 121.13 121.39 121.66 121.92 122.19 122.45 122.72 122.98 123.25 123.52 123.78 124.05
39 FT. 124.31 124.58 124.84 125.11 125.38 125.64 125.91 126.17 126.44 126.70 126.97 127.23
40 FT. 127.50 127.77 128.03 128.30 128.56 128.83 129.09 129.36 129.63 129.89 130.16 130.42

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-7
 26 GAUGE SQUARE FOOT CHART

5V CRIMP
24"
12"
1/2"

0" 1" 2" 3" 4" 5" 6" 7" 8" 9" 10" 11"

1 FT. 2.17 2.35 2.53 2.71 2.89 3.07 3.26 3.44 3.62 3.80 3.98 4.16
2 FT. 4.34 4.52 4.70 4.88 5.06 5.24 5.43 5.61 5.79 5.97 6.15 6.33
3 FT. 6.51 6.69 6.87 7.05 7.23 7.41 7.60 7.78 7.96 8.14 8.32 8.50
4 FT. 8.68 8.86 9.04 9.22 9.40 9.58 9.77 9.95 10.13 10.31 10.49 10.67
5 FT. 10.85 11.03 11.21 11.39 11.57 11.75 11.94 12.12 12.30 12.48 12.66 12.84

6 FT. 13.02 13.20 13.38 13.56 13.74 13.92 14.11 14.29 14.47 14.65 14.83 15.01
7 FT. 15.19 15.37 15.55 15.73 15.91 16.09 16.28 16.46 16.64 16.82 17.00 17.18
8 FT. 17.36 17.54 17.72 17.90 18.08 18.26 18.45 18.63 18.81 18.99 19.17 19.35
9 FT. 19.53 19.71 19.89 20.07 20.25 20.43 20.62 20.80 20.98 21.16 21.34 21.52
10 FT. 21.70 21.88 22.06 22.24 22.42 22.60 22.79 22.97 23.15 23.33 23.51 23.69

11 FT. 23.87 24.05 24.23 24.41 24.59 24.77 24.96 25.14 25.32 25.50 25.68 25.86
12 FT. 26.04 26.22 26.40 26.58 26.76 26.94 27.13 27.31 27.49 27.67 27.85 28.03
13 FT. 28.21 28.39 28.57 28.75 28.93 29.11 29.30 29.48 29.66 29.84 30.02 30.2
14 FT. 30.38 30.56 30.74 30.92 31.10 31.28 31.47 31.65 31.83 32.01 32.19 32.37
15 FT. 32.55 32.73 32.91 33.09 33.27 33.45 33.64 33.82 34.00 34.18 34.36 34.54

16 FT. 34.72 34.90 35.08 35.26 35.44 35.62 35.81 35.99 36.17 36.35 36.53 36.71
17 FT. 36.89 37.07 37.25 37.43 37.61 37.79 37.98 38.16 38.34 38.52 38.70 38.88
18 FT. 39.06 39.24 39.42 39.60 39.78 39.96 40.15 40.33 40.51 40.69 40.87 41.05
19 FT. 41.23 41.41 41.59 41.77 41.95 42.13 42.32 42.50 42.68 42.86 43.04 43.22
20 FT. 43.40 43.58 43.76 43.94 44.12 44.30 44.49 44.67 44.85 45.03 45.21 45.39

21 FT. 45.57 45.75 45.93 46.11 46.29 46.47 46.66 46.84 47.02 47.20 47.38 47.56
22 FT. 47.74 47.92 48.10 48.28 48.46 48.64 48.83 49.00 49.19 49.37 49.55 49.73
23 FT. 49.91 50.09 50.27 50.45 50.63 50.81 51.00 51.18 51.36 51.54 51.72 51.90
24 FT. 52.08 52.26 52.44 52.62 52.80 52.98 53.17 53.35 53.53 53.71 53.89 54.07
25 FT. 54.25 54.43 54.61 54.79 54.97 55.15 55.34 55.52 55.70 55.88 56.06 56.24

26 FT. 56.42 56.60 56.78 56.96 57.14 57.32 57.71 57.69 57.87 58.05 58.23 58.41
27 FT. 58.59 58.77 58.95 59.13 59.31 59.49 59.68 59.86 60.04 60.22 60.40 60.58
28 FT. 60.76 60.94 61.12 61.30 61.48 61.66 61.85 62.03 62.21 62.39 62.57 62.75
29 FT. 62.93 63.11 63.29 63.47 63.65 63.83 64.02 64.20 64.38 64.56 64.74 64.92
30 FT. 65.10 65.28 65.46 65.64 65.82 66.00 66.19 66.37 66.55 66.73 66.91 67.09

31 FT. 67.27 67.45 67.63 67.81 67.99 68.17 68.36 68.54 68.72 68.90 69.08 69.26
32 FT. 69.44 69.62 69.80 69.98 70.16 70.34 70.53 70.71 70.89 71.07 71.25 71.43
33 FT. 71.61 71.79 71.97 72.15 72.33 72.51 72.70 72.88 73.06 73.24 73.42 73.60
34 FT. 73.78 73.96 74.14 74.32 74.50 74.68 74.87 75.05 75.23 75.41 75.59 75.77
35 FT. 75.95 76.13 76.31 76.49 76.67 76.85 77.04 77.22 77.40 77.58 77.76 77.94

36 FT. 78.12 78.30 78.48 78.66 78.84 79.02 79.21 79.39 79.57 79.75 79.93 80.11
37 FT. 80.29 80.47 80.65 80.83 81.01 81.19 81.38 81.56 81.74 81.92 82.10 82.28
38 FT. 82.46 82.64 82.82 83.00 83.18 83.36 83.55 83.73 83.91 84.09 84.27 84.45
39 FT. 84.63 84.81 84.99 85.17 85.35 85.53 85.72 85.90 86.08 86.26 86.44 86.62
40 FT. 86.80 86.98 87.16 87.34 87.52 87.70 87.89 88.07 88.25 88.43 88.61 88.79

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-8 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE PANEL TRIM
DESCRIPTION NOTES
ITEM
PART NO. LENGTH GIRTH WEIGHT

CORNER TRIM ("PBU" PANEL - OUTSIDE) FL-10 10' - 2" 9 5/8" 7.50 #
3 5/16" 3/4" FL-10A 12' - 0" 9 5/8" 9.00 #
FL-10B 14' - 0" 9 5/8" 10.50 #

3/4"
3 5/16"

3/4"
3/4"

CORNER TRIM ("PBR" PANEL - OUTSIDE) FL-11 10' - 2" 11 3/4" 8.50 #
3 5/8" FL-11A 12' - 0" 11 3/4" 10.25 #
1 3/4"
FL-11B 14' - 0" 11 3/4" 11.90 #

3 1/8"
3/4"

1 3/4"
3/4"

BOX RAKE TRIM ("PBU" PANEL) FL-12 10' - 2" 20 3/4" 13.25 #
1 5/8" 6" FL-12D 20' - 2" 20 3/4" 26.50 #

1 1/8"

6 3/4"

RAKE ENDS FL-12A

CORNER BOX (Specify roof slope) 2 1/4"
FL-12B
PEAK BOX (Specify roof slope) 2" FL-12C

BOX RAKE TRIM ("PBR" PANEL) 1 3/16" FL-13 10' - 2" 20" 13.75 #
FL-13D 20' - 2" 20" 27.50 #
3/4" 5 1/2"

6 3/4"

RAKE ENDS FL-13A

2 1/4"
CORNER BOX (Specify roof slope) FL-13B
PEAK BOX (Specify roof slope) 2" FL-13C
"PBU" PANEL JAMB TRIM FL-20 7' - 3" 5" 2.60 #
FL-21 10' - 2" 5" 3.60 #
2 1/2"
FL-21B 12' - 3" 5" 4.40 #
FL-21C 14' - 2" 5" 5.13 #

1" 1/2"

1"

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-9
 26 GAUGE PANEL TRIM
DESCRIPTION NOTES
ITEM
PART NO. LENGTH GIRTH WEIGHT

"PBR" PANEL JAMB TRIM FL-22 7' - 3" 5" 2.60 #

2" FL-23 10' - 2" 5" 3.60 #
FL-23B 12' - 3" 5" 4.40 #
FL-23C 14' - 2" 5" 5.13 #
1 1/4"
1/2"

1 1/4"

HEAD TRIM ("PBR" & "PBU" PANELS) FL-24 3' - 6" 5 5/8" 1.25 #
FL-25 7' - 1" 5 5/8" 2.70 #
FL-26 10' - 4" 5 5/8" 3.80 #
2 1/2" FL-26B 12' - 3" 5 5/8" 4.65 #
FL-26C 14' - 2" 5 5/8" 5.41 #
1 1/4"

1 3/8"

JAMB OR HEAD CAP FL-37 10' - 2" 13 3/4" 10.00 #

8 1/8"

2 13/16"

FLAT RIDGE CAP FL-38 10' - 2" 24" 17.40 #

(1:12)

11 1/2" 11 1/2"

Specify Angle
"PBU" PANEL INSIDE CORNER FL-41 10' - 2" 9 3/4" 9.00 #
3/4"
3"

1 1/8"

3"

3/4" 1 1/8"

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-10 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE PANEL TRIM
DESCRIPTION NOTES
ITEM
PART NO. LENGTH GIRTH WEIGHT

"PBR" PANEL INSIDE CORNER FL-42 10' - 2" 13 1/2" 9.60 #

1-1/4"
3/4"
4 1/4"

4 1/4"

1 1/4"
3/4"

"PBR" PANEL TRANSITION FL-49A 10' - 2" 11 3/4" 8.50 #

3 3/4"

1 3/4"

5"
3/4"

"PBU" PANEL TRANSITION FL-50A 10' - 2" 10 3/8" 7.50 #

3 3/4"

1 1/8"

4 1/4"
3/4"

2X2 OUTSIDE ANGLE FL-27 10' - 2" 5" 3.60 #

2"

2"

2X2 INSIDE ANGLE FL-28 10' - 2" 5" 3.60 #

2"

2"

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-11
 26 GAUGE PANEL TRIM
DESCRIPTION NOTES
ITEM
PART NO. LENGTH GIRTH WEIGHT

3X3 OUTSIDE ANGLE FL-29 10' - 2" 7" 4.70 #

3"

3"

3X3 INSIDE ANGLE FL-30 10' - 2" 7" 4.70 #

3"

3"

PLAIN RIDGE CAP FL-600 10' - 2" 14 1/2" 9.71 #

2 1/2"
1/2"
4"

1/4" 1/4"

Specify Angle
DENVER ENDWALL AND HIGH FL-555 10' - 2" 10 1/2" 7.80 #
SIDE PARAPET TRIM
4"

5 1/2"

Specify Angle
BASE TRIM FL-601 10' - 2" 4 13/16" 3.56 #

1 1/2" 1"

1 13/16"

1/2"

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-12 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE PANEL TRIM
DESCRIPTION NOTES
ITEM
PART NO. LENGTH GIRTH WEIGHT

BASE TRIM FL-530 10' - 2" 6 3/4" 3.81 #

2"
1 3/4"

45⁰

2 1/2"

1/2"

CORNER TRIM FL-602 10' - 2" 12 1/2" 9.74 #

1 1/4"
1/2" FL-602A 12' - 6" 12 1/2" 11.67 #
FL-602B 14' - 6" 12 1/2" 13.62 #
FL-602C 16' 12 1/2" 15.56 #
4 1/4"
1/2"
4 1/4"

1 1/4"

SHINGLE RAKE TRIM FL-606 10' - 2" 9 1/2" 7.57 #

3"

4 1/2"

1 1/4"
1/4" 1/2"

CUSTOM SOFFIT (X=12") FL-607 10' - 2" 20" 15.50 #

(X=14") FL-607A 10' - 2" 22" 17.00 #
(X=16") FL-607B 10' - 2" 24" 18.60 #

5 1/2"
X

2" 1/4"

Z FLASHING FL-610 10' - 2" 4 1/4" 3.30 #

1 1/2"
1"

1 1/2"

1/4"

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-13
 26 GAUGE PANEL TRIM
DESCRIPTION NOTES
ITEM
PART NO. LENGTH GIRTH WEIGHT

J CHANNEL FL-611 10' - 2" 3 7/8" 3.30 #

1/4" 2"

3/4"

7/8"

DOOR POST TRIM (X=5 1/2") FL-612 10' - 2" 7 1/2" 5.82 #
1 1/2"
(X=7 1/4") FL-612A 10' - 2" 9 1/4" 7.18 #

1/4"

1/4"

WINDOW DRIP CAP FL-614 10' - 2" 3 1/4" 2.32 #

1 1/2"
1"
1/2"

BASE TRIM - ALL PANELS FL-72 10' - 2" 6 1/8" 4.38 #

3 1/4"
1 3/4"

5/8"
135⁰

CANNONBALL TRACK COVER FL-615 10' - 2" 12" 9.12 #

1 3/8"

6 7/8"
1 5/8"

1 3/8"

3/4"

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-14 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE PANEL TRIM
DESCRIPTION NOTES
ITEM
PART NO. LENGTH GIRTH WEIGHT

TOP MOUNT TRACK COVER FL-616 10' - 2" 10 3/8" 8.06 #

1" 3"

4"

1 5/8"
3/4"

OVERHEAD DOOR TRIM (7 7/8") FL-617 10' - 2" 12" 9.31 #

7 7/8"

3/4" 1/4"
1 1/2"
7/8"

OVERHEAD DOOR TRIM (9 1/8") FL-617A 10' - 2" 13 1/4" 9.94 #

9 1/8"

3/4" 1/4"
1 1/2"
7/8"

STANDARD VALLEY FL-556 10' - 2" 24" 12.87 #

1"

11"

45⁰

Specify Pitch

EAVE TRIM FL-19 10' - 2" 9" 5.00 #

5"

3 1/2"

1/2"

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-15
 26 GAUGE PANEL TRIM
DESCRIPTION NOTES
ITEM
PART NO. LENGTH GIRTH WEIGHT

STANDARD VALLEY AG-237 10' - 2" 22" 14.16 #

COLOR AG-238 20' - 2" 22" 28.32 #
SPECIFY
ANGLE

1"
10" 10"

Specify roof pitch

EXTENDED VALLEY AG-239 10' - 2" 42 3/4" 28.29 #

COLOR
AG-240 20' - 2" 42 3/4" 56.58 #
SPECIFY
ANGLE

1"
20 3/8" 20 3/8"

Specify roof pitch

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-16 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE 5V-CRIMP TRIM
ITEM PART NO. LENGTH GIRTH WEIGHT NOTES
RIDGE/HIP FLASH AG-202 10' - 2" 13" 8.37 #
COLOR
AG-203 20' - 2" 13" 16.74 #
6" 6"

SPECIFY
ANGLE

RAKE TRIM COLOR 4" 1 1/2" AG-248 10' - 2" 12 1/8" 7.81 #
AG-249 20' - 2" 12 1/8" 15.62 #
4" 1"

5/8"

RAKE TRIM COLOR

2 1/2"
5/8" AG-250 10' - 2" 8 3/4" 5.64 #
AG-251 20' - 2" 8 3/4" 11.28 #
1"
3"

5/8"

EAVE TRIM AG-246 10' - 2" 7 5/8" 4.51 #

3 1/2"
COLOR
AG-247 20' - 2" 7 5/8" 9.02 #
Specify
Angle
3"

5/8"

DRIP EDGE 2 1/2" 1 1/2" AG-279 10' - 2" 9 5/8" 6.18 #

90⁰
3"
COLOR
5/8"

CONTINOUS CLEAT FL-338 10' - 2" 3" 2.45 #

135⁰

1/2"

2 1/2"

Z CLOSURE AG-274 10' - 2" 2 3/4" 1.78 #

1"
3/4"
1/2"

135⁰
1"

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-17
 26 GAUGE ACCESSORIES
DESCRIPTION NOTES
ITEM SQ. FT. PIECE
PART NO. LENGTH COLOR TYPE WEIGHT WEIGHT

"R" LIGHT TRANSMITTING High Strength Fiberglass

PANEL HW-1509 10' - 8" White 1 16.89 #
8 oz.

High Strength Acrylit - U.V. Resistant

HW-1432 10' - 8" White 1 8 oz. 16.89 #

HW-1434 11' - 0" White 1 8 oz. 17.42 #
HW-1436 12' - 0" White 1 8 oz. 19.00 #

"U" LIGHT TRANSMITTING High Strength Fiberglass

PANEL HW-1542 10' - 8" White 1 16.89 #
8 oz.

High Strength Acrylit - U.V. Resistant

HW-1438 10' - 8" White 1 8 oz. 16.89 #

HW-1440 12' - 0" White 1 8 oz. 19.00 #

DESCRIPTION
GENERAL COLOR WEIGHT
FLAT SHEETS

40 7/8" X 126" COLOR 29.59 #

GALVANIZED
42 3/4" X 126" GALVALUME PLUS 28.98#
& COLOR
Skidding charge of $42.00 will be added

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-18 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE ACCESSORIES
DESCRIPTION NOTES
ITEM PART CARTON CARTON
TYPE ADHESIVE SIZE
NO. SIZE WEIGHT

"PBR" PANEL CLOSURE HW-455 INSIDE YES 1" X 36" 100 4.09 #
STRIP HW-456 OUTSIDE NO 1" X 36" 100 8.32 #

"PBU" PANEL CLOSURE HW-459 INSIDE YES 1" X 36" 100 4.05 #
STRIP HW-460 OUTSIDE NO 1" X 36" 100 6.27 #

5V CRIMP CLOSURE HW-450 INSIDE YES 1" X 24" 100 3.30 #

STRIP HW-452 OUTSIDE NO 1" X 24" 100 4.10 #

ITEM DESCRIPTION
PART CARTON ROLL
TAPE SEALER GENERAL LENGTH
NO. SIZE WEIGHT
HW-507 1/2" X 3/32" 50'-0" 20 1.70 #
HW-508 1" X 1/8" 40'-0" 12 3.50 #
HW-509 1 5/8" X 1/8" 30'-0" 10 2.30 #

FLAT

PART CARTON CARTON

GENERAL LENGTH
NO. SIZE WEIGHT
DOUBLE BEAD HW-500 7/8" X 3/16" 25'-0" 8 15.16 #
SEALER

SOLD IN FULL CARTONS ONLY

TRIPLE BEAD HW-502 2 1/2" X 3/16" 20'-0" 6 21.00 #

SEALER

SOLD IN FULL CARTONS ONLY

TRI-BEAD HW-504 7/8" X 3/16" 25'-0" 8 17.74 #

SEALER

SOLD IN FULL CARTONS ONLY

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-19
 26 GAUGE ACCESSORIES
FASTENERS
(SCREWS, NAILS, RIVETS)
DESCRIPTION NOTES
LB. PER 250
DESCRIPTION PART NO. LENGTH
PIECE BAG
SILVER SENTRI® 8A 10 X 1" 2.18 #
WOODGRIP LONG LIFE 8 10 X 1 1/2" 2.70 #
COATED FASTENER 8B 10 X 2" 3.28 #
8C 10 X 2 1/2" 3.85 #

OTHER SIZES
AVAILABLE
Head Size 1/4" (Panel To Solid Wood) Please inquire. 250 Per Bag
ZAC® LONG LIFE 9A 10 X 1" 3.55 #
WOODGRIP FASTENER 9 10 X 1 1/2" 4.58 #

OTHER SIZES
AVAILABLE
Head Size 5/16" (Panel To Solid Wood) Please inquire. 250 Per Bag

STAINLESS STEEL 216 10 X 1" 2.33 #

WOODGRIP 217 10 X 1 1/2" 2.83 #
218 10 X 2" 3.33 #
219 10 X 2 1/2" 3.58 #

Head Size 5/16" (Bi-Metal Fastener) 100 Per Bag

SELF-DRILLER 17A 12 X 1 1/4" 3.88 #

Head Size 5/16" Panel To Metal 250 Per Bag

SELF-DRILLER LAP-TEK 4A 14 X 7/8" 4.00 #
Paint setup
charges apply

Head Size 5/16" Panel To Panel 250 Per Bag

SELF TAPPING 18 14 X 1" 4.13 #
Special Order 18B 14 X 1 1/2" 5.15 #
UPS Charges apply

Head Size 3/8" (Panel To Plywood) Pre-Drill Holes 250 Per Bag
POP RIVET 14 1/8" X 3/16" .73 #

(Stainless Steel) 250 Per Bag

PANCAKE HEAD 13 10 x 1" 1.78 #
(Recommended for Royal Lock
and SL Series)

#2 Phillips - Wood Grip Panel to Plywood 250 Per Bag

LONG LIFE LAP TEK 4 14 X 7/8" 5.43 #

HEAD SIZE 3/8" 250 Per Bag

American Building Components recommends a #14 X 1", Type “A”, hex head fastener with
washer for all exposed fastener panels applied over a plywood or OSB substrate. The use of
a #9 or #10 “wood grip” type fastener into plywood or OSB substrates is not recommended.
This refers to exposed fastener panels installed over solid decks only. Open purlin
construction, such as 2 X 4’s on 24" center, should be fastened with #9 or #10 “wood grip”
type fasteners.
NOTE: Other lengths and sizes available, PLEASE INQUIRE. Not all fasteners in stock, UPS and $25.00 paint charges will apply.
FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 26GA-20
VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE ACCESSORIES
ROOFING NAILS
PART NO. LENGTH QTY. PER LB. NOTES
(Price Per LB.)
FLAT CHECKERED-HEAD HW-364 1 1/2" 126
RING SHANK HW-367 2" 100
(with Rubber Washer) HW-368 2 1/2" 82

Sold in 5 LB. and 50 LB. cartons

ITEM DESCRIPTION NOTES
PART NO. GENERAL

TOUCH UP PAINT - Spray HW-306 Spray Can

Cans (6oz by Volume) 4.25 oz. Net Weight
* Std. Colors (Recommended for field painting
of accessories only.) NOTE: Spray cans cannot be shipped via Air.
TOUCH-UP PAINT - HW-304 2 oz. Can
Brush Top Can
* Std. Colors (Recommended for minor scratch
cover only.)

1/4" ONE PIECE MAGNETIC HW-606

SOCKET
ACRYLIC EDGE COAT HW-325 Pint
Color: Clear
Recommended for cut edges.
JOINT SEALER HW-552 5 oz. Tube
(Color: Aluminum) .30 # ea.
SILICONE* CAULK HW-546 Color: Clear
*Silcone caulk not recommended for panel applications.
URETHANE CAULK HW-540 Color: White
HW-542 Color: Bronze
HW-544 Color: Almond

VENT MATERIAL
ITEM PART NO. PROFILE LENGTH NOTES
PROFILE VENT HW-116R PBR Panel 100' Roll
(Pkgd. in
HW-116U PBU Panel Two 50' Rolls)

ITEM PART NO. GENERAL CARTON WEIGHT NOTES

SIZE EACH
PROFILE VENT HW-2075 1" Profile Vent 25 .05 #
Anchor Clip Anchor Clip

Sold in 25 pc. boxes only

ITEM PART NO. GENERAL CARTON LENGTH
SIZE
VERSA VENT HW-111 1" Thickness 10 10’-0”

HW-112 1 1/4" Thickness 10 10’-0”

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-21
 Profile Vent

NEW OR RE-ROOF ON PURLIN OR WOOD DECK CONSTRUCTION

Use a 2" opening at the ridge to provide ventilation. On new or re-roof wood deck construction cut a 2"
slot at the ridge (1" each side, start cut 6" from gable ends). On purlin construction position panels to
leave a 2" opening.

IMPORTANT NOTE:
This ventilation system is not guaranteed to be weather proof under all conditions. Many factors affect the
weather tightness of this or any ventilator apparatus. ABC recommends consulting a qualified architect,
design engineer, or HVAC professional for your particular application.

TECHNICAL DATA

Passed Net Free Area 1" nom. thickness 8.5 sq. in. per lin. ft. per slope
(17 sq. in. per lin. ft. ridge)
Passed Air Permeability ASTM D737 >>760 cu. ft. per minute
Passed Self-ignition Temp. ASTM D1929 963° F
Passed Cold Crack Loren C115 Resistance to >-25° F
Passed Snow Infiltration CRL 5704 -0-
Passed Tear Strength ASTM D1294-86 Tear: Machine 25 p.p.i.
Counter 25 p.p.i.
Passed Tensile Strength ASTM D2261-83 Tensile: Machine 25 p.p.i.
Counter 25 p.p.i.
Passed Attic Dust Test ASTM D1739-98 No Clogging, will not hold dust
Passed Dust Exposur e Test ICBO AC132
Passed Lor en Compression 13%
Recovery 100%
Passed UV Stable Chamber Test No change to color or materials
Passed Abrasion Test ASTM D1175 No damage to panel surface
Passed 100 MPH Wind Driven Rain Test

NOTE 1: When ordering profile vent for panels that are striated use HW-116SL12 for SL-12® or HW-116SL16 for SL-16®.

NOTE 2: Use appropriate length fasteners to affix Ridge Cap through Profile Vent into Deck. Use Tri-Bead Tape
Sealer at Profile Vent/Deck interface. DO NOT USE POP RIVETS.

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-22 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 TERMS AND CONDITIONS OF SALE
1. Parties - All references to ABC or Seller refer to Metal Building Components L.P. (hereinafter "Seller" or "ABC"). Seller and Buyer may sometimes collectively be referred to herein as the "parties."

2. Binding Effect - The following terms and conditions (the "Terms and Conditions") shall apply to any and all sales between Seller and the Buyer and shall not be waived, modified or amended without the express written consent of the
Seller's President or Executive Vice-President. Terms contained within any other purchase order or agreement issued by Buyer conflicting with these Terms and Conditions shall be of no force and effect. All sales by Seller of any nature to
Buyer shall be made under the provisions of this Agreement. Any documents that Buyer may use for its convenience including, but not limited to, purchase orders or sales acknowledgement forms shall be deemed to be for the administrative
convenience of Buyer only, and this Agreement as well as the terms and conditions as stated in Seller's invoices and bills of lading shall supersede and take precedence over any of Buyer's terms and conditions which may be contained on any
such forms. Further, should Seller act upon this Agreement without first obtaining Buyer's signature on a Purchase Order, Buyer hereby irrevocably agrees to be bound by this Agreement to the exclusion of any contrary terms and conditions
proposed by Buyer. All orders are subject to approval and acceptance by Seller.

3. Payment - Payments due Seller under the terms of this sale and any other money due Seller by Buyer shall be paid to Seller at its Houston, Harris County, Texas office. Unless otherwise agreed in advance and in writing by Seller's Credit
Department, payment for the materials and/or services under this Agreement shall be COD. Any and all different credit terms must be pre-approved in writing by Seller's Credit Department. If Seller grants Buyer credit terms, invoices paid
Seller by Buyer within ten (10) days of date of invoice may be allowed ½% discount, net due thirty (30) days from date of invoice. C.O.D. shipments paid at the time of shipment are not allowed discount. In the event Seller grants Buyer credit
terms, said credit terms are subject to change at any time, for any reason, at the sole discretion of Seller without prior written notice to Buyer. Unless specifically enumerated herein, the price does not include any taxes (including excise, privi-
lege, occupation, use, sales, etc.; Federal, State or local) or costs of shipment. All materials sold hereunder are sold F.O.B. Seller's plants. Seller reserves the right to approve the carrier on all C.O.D. shipments.

4. Lien/Release - Buyer agrees that all payments with lien release language on the back of any check shall be sent only to Seller at its Houston, Harris County, Texas office. Buyer agrees that any payment accepted through Seller's lock box
with lien release language on the check does not bind Seller to the attempted release. Seller's agent at the lock box who endorses and/or accepts checks for Seller is authorized only to accept unconditional payments, and no action by this
agent shall ever give rise to a claim of any authority, apparent or otherwise, beyond that described in this paragraph. Acceptance of any conditional check, including any lien release language or otherwise at the lock box shall only be a partial
release for those funds received, and never otherwise. This paragraph cannot be waived or modified except in writing in advance by the President of Seller.

5. Interest/Costs of Collection - Any payments deferred after the due date as specified herein shall bear interest at the greater of the rate of ten percent (10%) per annum or a rate equal to the maximum non-usurious rate under applicable
law. If an invoice becomes past due, is placed in the hands of an attorney for collection, if collected by any legal proceedings, or if this Agreement is relevant to any other dispute between the parties, in addition to any other amounts and dam-
ages recovered by Seller, Buyer agrees to pay Seller any and all attorney's fees and costs incurred in the collection of sums owed by Buyer to Seller on account of principal, interest or other charges, which attorneys' fees shall not be less than
thirty percent (30%) of the total amount payable. "Costs incurred in the collection of sums" as used herein is not to be limited to costs incurred in litigation, but includes, without limitation, copying and mailing expenses, lien fees, lost manage-
ment time, inspection expenses and expert witnesses expenses in addition to taxable costs incurred in litigation.

6. Security Interest - Buyer has and does by these presents grant to Seller and Seller has and does hereby retain a security interest in all parts and accessories described in and being purchased by Buyer pursuant to this Agreement. The
security interest herein granted by Buyer and retained by Seller is to secure payment of the full purchase price and all other charges due and owing Seller by Buyer under the terms of this sale. This Agreement is governed by Section 2.101, et.
seq. of the Texas Business & Commerce Code, and the security interest hereunder constitutes a "purchase money security interest" pursuant to the Uniform Commercial Code, This instrument is a contract, security agreement and financing
statement between the Parties hereto.

7. Authorization for Credit History - The Buyer or undersigned individual who is either the credit applicant or a principal/agent of the Buyer, recognizes that a credit history report may be a factor in the evaluation of the credit history of the
Buyer. Buyer, therefore, consents to and authorizes the use of a commercial, consumer or any other credit report on the Buyer or undersigned individual by Seller from time to time as may be needed in the credit evaluation process.

8. Buyer Responsible for Accuracy of Order/Delivery - Buyer hereby assumes responsibility for the accuracy of verbal orders unless written confirmation is received prior to fabrication. Confirming orders should be marked "Confirming
Order-Do Not Duplicate." Buyer may arrange for pickup of order at ABC's plant or shipment will be made by common carrier - "Freight Collect" - unless other arrangements are previously made.

9. Cancellation - Either party may cancel this Agreement by giving written notice to the other party not less than seven (7) days prior to the cancellation date; provided, however, that the Terms and Conditions provided herein shall apply and
remain in full force and effect with respect to any and all transactions entered into by and between Seller and Buyer. In the event of such cancellation, Buyer agrees to pay Seller for any and all costs and damages occasioned by the cancella-
tion hereof including, but not limited to, Seller's expenses of order processing, engineering, detailing, purchase of material, fabrication and sales commissions and applicable incidental, consequential and lost profits damages; provided, however,
in no event will the amount payable by Buyer pursuant to this sentence be less than $2,500.

10. Manufacturer's Warranties/Disclaimer - Seller warrants its workmanship only against failure due to defective material or workmanship for a period of one (1) year from date of manufacture; however, Buyer's sole and exclusive remedy
shall be limited to, in Seller's sole discretion, the replacement of defective parts, F.O.B. Seller's plant (transportation, redesign, dismantling, disposal of material and installation are not included), or repair of defective parts. As a condition prece-
dent to the effectiveness of the any warranty, all amounts owing to Seller under this or any other agreement with Seller or Seller’s affiliates must be fully paid. Seller's liability shall be strictly limited to the written express warranties specified
herein, and Buyer agrees and stipulates that Seller shall not be liable for any direct, incidental, consequential, liquidated or exemplary damages, which Buyer may suffer for any reason, including reasons attributable to Seller. Seller does not
warrant products that are not manufactured by Seller except to the extent of the warranty ABC may actually pass through or assign from the manufacturer. EXCEPT AS STATED ABOVE, SELLER HEREBY EXPRESSLY DISCLAIMS ALL
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE, AND THE PARTIES HERETO HEREBY STIPULATE
THAT ALL SUCH WARRANTIES ARE HEREBY DISCLAIMED. Claims for shortages or defective materials must be made to Seller in writing within five (5) days after delivery of shipment (which the Parties agree is a reasonable time), or claim
shall be conclusively waived.

11. No Incidental, Special or Consequential Damages - Notwithstanding any other agreement to the contrary, Buyer hereby agrees and stipulates that Seller shall not be liable for any incidental, special, compensatory, expectation, exem-
plary or consequential damages, which Buyer may suffer for any reason, including reasons attributable to Seller.

12. Weathertightness Warranty - In the event that Buyer purchases a WeatherTightness Warranty, all Seller procedures must be strictly followed for issuance and effectiveness of the warranty, and Buyer must have paid in full all invoices for
materials and the warranty before the Weathertightness Warranty will be issued. As a condition precedent to the issuance of a Weathertightness Warranty by Seller, Buyer must not have any outstanding payables owed to Seller or any of
Seller's subsidiaries or affiliates.

13. Drawings - If Seller prepares shop drawings, the shop drawings will be in accordance with the Seller's Lump Sum Buyers Agreement which was prepared from the plans and specifications supplied by Buyer to Seller. The shop drawings
shall be submitted to Buyer for approval. All materials sold will be in substantial compliance to approved shop drawings only. The approval stamp on the shop drawings shall be signed by the Buyer or his Representative and made a part here-
of, and shall be an indication of the accuracy of the shop drawings.

14. Acceptance of Change Orders - Buyer may submit a written request for change orders to Seller adding, deleting or altering the Quantity, Description or Specifications of material ordered. Seller, upon receipt of a written request for
change order, shall price the requested changes and send to Buyer a price quotation thereof. Seller shall be under no obligation to accept or perform a request for change order unless Buyer accepts in writing, without alteration or adjustment,
the change order at the prices and terms quoted by Seller.

15. Insurance - Buyer will, at its sole expense, maintain insurance during the performance of the services covered by this agreement and thereafter, including General Liability Insurance with a per occurrence limit of not less than $1,000,000
covering Seller with respect to any involvement in the performance and/or services covered by this agreement. This insurance will include products liability and completed operations liability coverages, which will extend for three (3) years after
the completion of the services. Buyer agrees to name Seller as an additional named insured with respect to the coverages required to be maintained by this agreement and to provide Seller with a conformed Additional Named Insured
Endorsement setting forth the coverages required by this agreement. Buyer agrees that its insurance coverages as required by this agreement shall be primary to and not concurrent with any insurance coverages maintained by Seller and that
any such coverages maintained by Seller shall in no way be implicated unless and until all available coverages required by this agreement shall have been fully exhausted.

16. Effect of Sale - All materials sold hereunder to Buyer are final and cannot be returned to Seller for credit unless Buyer obtains prior written approval from Seller's authorized representative. If, at Buyer's request, the delivery of materials is
delayed, then ABC shall invoice Buyer for the price of materials, which invoice shall be due in accordance with the terms of payment provided herein. Buyer shall reimburse ABC for the cost of storing materials if shipment is delayed by Buyer,
and will assume any damages to the materials caused by deterioration. In the unlikely event Seller agrees to accept return of some of the materials, a 25% restocking fee shall be charged on all returned materials.

17. Force Majeure - Seller shall not be liable to Buyer for liquidated damages, back charges or loss of use to Buyer arising out of any delay or any other reason in carrying out this Agreement. Under no circumstances shall Seller be liable
in any way to Buyer, building owner or any other party for delays, failure in performance, or loss or damage due to force majeure conditions including, without limitation: fire; flood; epidemics; quarantine; lightening; strike;
embargo; explosion; power surge or failure; acts of God; war; labor or employment disputes; civil disturbances; acts of civil or military authority; inability to secure materials, fuel, products or transportation facilities; acts or
omissions of suppliers; or any other causes beyond ABC's reasonable control, whether or not similar to the foregoing. FURTHER, BUYER HEREBY AGREES AND STIPULATES THAT, IN THE EVENT SELLER RECEIVES NOTIFI-
CATION OF A SCHEDULED PRICE INCREASE FROM ANY OF ITS SUPPLIERS BETWEEN THE DATE OF THIS AGREEMENT AND THE DATE SCHEDULED FOR DELIVERY OF THE MATERIALS COVERED HEREBY, SELLER
RESERVES THE RIGHT, IN ITS SOLE DISCRETION, TO INCREASE THE PURCHASE PRICE STATED HEREIN IN AN AMOUNT CORRESPONDING TO SAID PRICE INCREASE. Buyer agrees this limitation of Seller's liability is reason-
able. Buyer further agrees that this limitation of Seller's liability is part of the consideration for this Agreement and is reflected in the amounts charged by Seller hereunder. Buyer intends that this limitation on Seller's liability be liberally con-
strued in favor of Seller to eliminate any other liability of Seller other than repair or replacement of defective products.

18. Jurisdiction/Venue/Waiver of Trial by Jury - Buyer hereby acknowledges, stipulates and agrees that (i) any and all claims, actions, proceedings or causes of action relating to the validity, performance, interpretation, and/or enforcement
hereof must be submitted to a court of competent jurisdiction in Houston, Harris County, Texas, (ii) to the maximum extent practicable, this Agreement will be deemed to call for performance in Harris County, Texas, (iii) Buyer irrevocably sub-
mits itself to the jurisdiction of the state and federal courts in Harris County, Texas, (iv) service of process may be made upon it in any legal proceeding in connection with this Agreement or any other agreement as provided by Texas law, (v)
Buyer irrevocably waives, to the fullest extent permitted by law, any objection that it may now or hereafter have to the laying of venue of any litigation arising out of or in connection with this Agreement or any other agreement or transaction
brought in any such court, (vi) Buyer irrevocably waives any claims that litigation brought in any such court has been brought in an inconvenient forum, and (vii) it irrevocably consents to the service of process out of any of the aforementioned
courts by the mailing of copies thereof by Certified Mail, Return Receipt Requested, postage prepaid, at its address set forth herein. The scope of each of the foregoing waivers is intended to be all encompassing. Buyer acknowledges that this
waiver is a material inducement to the agreement of Seller to enter into a business relationship, and that Seller has already relied on this waiver in entering into this Agreement. EACH PARTY HEREBY AGREES NOT TO ELECT A TRIAL BY
JURY OF ANY ISSUE TRIABLE OF RIGHT BY JURY, AND FULLY WAIVES ANY RIGHT TO TRIAL BY JURY TO THE EXTENT THAT ANY SUCH RIGHT NOW OR HEREAFTER EXISTS WITH RESPECT TO THIS AGREEMENT AND/OR
THE AGREEMENTS, INSTRUMENTS AND DOCUMENTS CONTEMPLATED HEREBY OR ANY CLAIM, COUNTERCLAIM OR OTHER ACTION ARISING IN CONNECTION HEREWITH. EACH PARTY ACKNOWLEDGES AND AGREES
THAT THIS WAIVER OF RIGHT TO TRIAL BY JURY IS GIVEN KNOWINGLY AND VOLUNTARILY BY SUCH PARTY AND IS INTENDED TO ENCOMPASS EACH INSTANCE AND EACH ISSUE AS TO WHICH THE RIGHT TO TRIAL BY
JURY WOULD OTHERWISE ACCRUE. EITHER PARTY IS HEREBY AUTHORIZED TO FILE A COPY OF THIS SECTION IN ANY PROCEEDING AS CONCLUSIVE EVIDENCE OF THIS WAIVER.

19. Indemnification - BUYER ASSUMES ENTIRE RESPONSIBILITY AND LIABILITY FOR ANY CLAIMS OR ACTIONS BASED ON OR ARISING OUT OF INJURIES, INCLUDING DEATH, TO PERSONS OR DAMAGES TO OR
DESTRUCTION OF PROPERTY, SUSTAINED OR ALLEGED TO HAVE BEEN SUSTAINED IN CONNECTION WITH OR TO HAVE ARISEN OUT OF OR INCIDENTAL TO THE PERFORMANCE OF THIS CONTRACT BY BUYER, ITS
AGENTS AND EMPLOYEES, AND ITS SUBCONTRACTORS, THEIR AGENTS AND EMPLOYEES, INCLUDING CLAIMS OR ACTIONS FOUNDED IN WHOLE OR IN PART UPON THE ALLEGED ACTS, OMISSIONS OR NEGLIGENCE OF
SELLER, SELLER'S REPRESENTATIVES, OR THE EMPLOYEES, AGENTS, INVITEES, OR LICENSEES THEREOF. BUYER FURTHER AGREES TO DEFEND, INDEMNIFY AND HOLD HARMLESS SELLER AND ITS REPRESENTA-
TIVES, AND THE EMPLOYEES, AGENTS, INVITEES AND LICENSEES THEREOF IN RESPECT OF ANY SUCH MATTERS AND AGREES TO DEFEND ANY CLAIM OR SUIT OR ACTION BROUGHT AGAINST SELLER, SELLER'S REP-
RESENTATIVE, AND THE EMPLOYEES, AGENTS, INVITEES AND LICENSEES THEREOF. THE PARTIES HEREBY WAIVE THEIR RESPECTIVE RIGHTS UNDER THE DECEPTIVE TRADE PRACTICES-CONSUMER PROTECTION
ACT, SECTIONS 17.41 THROUGH 17.63 INCLUSIVE, OF THE TEXAS BUSINESS AND COMMERCE CODE, A LAW THAT GIVES CONSUMERS SPECIAL RIGHTS AND PROTECTIONS. AFTER CONSULTATION WITH LEGAL COUN-
SEL, EACH VOLUNTARILY CONSENTS TO THIS WAIVER.

20. Severability - Each of the provisions of this Agreement is a separate and distinct agreement and independent of the others. If any provision of this Agreement is found to be invalid or unenforceable in any jurisdiction, such provision shall
be fully severable in such jurisdiction, and this Agreement shall be construed and enforced as if in such jurisdiction such provision had never comprised a part hereof. In such event, the remaining provisions of this Agreement shall remain in full
force and effect. The terms of this Agreement are intended by the parties as a final expression of their agreement containing all oral and written understandings between the parties relative to the materials generally described in this Agreement.

21. Acceptance/Entire Agreement - As a condition precedent to the effectiveness of an order, all orders are subject to approval and acceptance by Seller. This Agreement, along with any attached exhibits, constitutes the entire agreement of
the parties herein.

AGREED AND ACCEPTED:

Signature Date

ABC RESERVES THE RIGHT TO CHANGE THESE TERMS AND CONDITIONS WITHOUT NOTICE. EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE PRODUCT INFORMATION

HOW TO ORDER
SPECIAL FLASHING
NOTE:
1. Always dimension each segment
2. Always put in degrees of each angle.
3. Always use degrees on inside angle from line
to line (never use angle to a non-existing line).
4. Always show where color goes on each piece.
5. Calculate girth (flat width). 80° 90° 100°110°
70°
60° 120°
50° 130°
135°
40° 140°
30° 150°
20° 160°

10° 170°
8
7
6
0° 180°
5
4
3
2 128° 8:12
1 123° 7:12
119° 6:12
113° 5:12
RIDGE ANGLE 109° 4:12
104° 3:12
1:12 = 170° 100° 2:12
2:12 = 161° 95° 1:12
90° FLAT
3:12 = 152°
4:12 = 143° EAVE ANGLE
5:12 = 135°
6:12 = 127°
7:12 = 120°
8:12 = 113°

ANGLE CHART FOR

HIP, VALLEY, RIDGE, GUTTER and PITCH BREAK TRIM
RIDGE TRANSITION GUTTER HIP
VALLEY

ROOF SLOPE
1:12 2:12 3:12 4:12 5:12 6:12 7:12 8:12 9:12 10:12 11:12 12:12

HIP AND VALLEY 173º 166º 160º 154º 148º 143º 138º 133º 129º 126º 123º 120º

RIDGE 170º 161º 152º 143º 135º 127º 120º 113º 106º 100º 95º 90º

GUTTER AND PITCH BREAK 94º 99º 104º 108º 112º 116º 120º 123º 126º 129º 132º 135º

FOR THE MOST CURRENT INFORMATION SUBJECT TO CHANGE WITHOUT NOTICE

PAGE 26GA-24 VISIT www.abcmetalroofing.com EFFECTIVE DATE APRIL 10, 2006
 26 GAUGE COLOR CHART
HAWAIIAN BLUE *¨CRIMSON RED BURNISHED SLATE
ASH GRAY AZTEC GOLD CHARCOAL GRAY
KOKO BROWN SADDLE TAN DESERT SAND
POLAR WHITE RUSTIC RED LIGHT STONE
COLONY GREEN FERN GREEN GALLERY BLUE

All colors except Crimson Red contain not more than .06% lead.
*Use this color for applications which meet Federal, State and local regulations for lead-based paints.
¨20 - Year Warranty not available for Crimson Red.

See appropriate color chart for sample of color selection.

Final color selection should be made from actual painted metal color chips.

20 YEAR LIMITED WARRANTY AVAILABLE UPON WRITTEN REQUEST

Galvalume® and Galvalume Plus® is a registered trademark of BIEC International.

SUBJECT TO CHANGE WITHOUT NOTICE FOR THE MOST CURRENT INFORMATION

EFFECTIVE DATE APRIL 10, 2006 VISIT www.abcmetalroofing.com PAGE 26GA-25
NOTES
NOTES
 Big Rapids Rome
Omaha Oskaloosa
Salt Lake City

Nicholasville
Oklahoma City
Phoenix
Lubbock
Jackson

Contact American Building Components at

the plant located nearest you for
information on any of our fine products.
For the most current information see our website at
www.abcmetalroofing.com

AMERICAN
BUILDING
® COMPONENTS
BIG RAPIDS, MI JACKSON, MS LUBBOCK, TX NICHOLASVILLE, KY OKLAHOMA CITY, OK
866-334-4222 800-877-8709 800-481-3035 800-877-8709 800-228-2260

OMAHA, NE OSKALOOSA, IA PHOENIX, AZ ROME, NY SALT LAKE CITY, UT

800-228-2260 800-345-0044 800-481-3035 800-544-2651 800-481-3035

Rugged Rib®, Regal Rib®, Imperial Rib®, Ameri-Drain®, Monarch Rib®, 7/8" Wide Rib®, Perma Clad®, SL-16®, and
Royal Lock® are registered trademarks of American Building Components. Galvalume® and Galvalume Plus® are
registered trademarks of BIEC International. 04-06-10M