Section

Note: Where available, SAP numbers are listed first for the parts and tools in this
section. Former (legacy) part numbers are listed in parentheses. N/A in place of the
SAP number denotes that a SAP number has not yet been assigned for that part. 2b
RTTS Model 2 Circulating Valves
The table below lists the tools and procedures discussed in Section 2b.

Topic Page
General 1
Prejob Considerations 2
Paint and Coating Policy 2
Paint and Coating Specifications 2
Lubrication for Sour-Gas Tools 2
Lubrication for Downhole Tools 2
Operating Procedures 3
Installing the Model 2 Circulating Valve on the RTTS Packer 3
Operating the Model 2 RTTS Circulating Valve 3
Maintenance Procedure for the RTTS Model 2 Circulating Valve 3
Conversion Parts 3
N/A (696.5907)—Model 2 Circulating Valve—8 5/8 in. with 41/2-in. IF threads 6
5 3
N/A (696.6019)—Model 2 Circulating Valve—9 /8 in. to 11 /4 in. with 4 /2-in. IF threads 1 8
N/A (696.6031)—Model 2 Circulating Valve—13 3/ in. with 41/ 10
8 2-in. IF threads
1/ 13
N/A (696.6041)—Model 2 Circulating Valve—16 in. with 4 2-in. IF threads
N/A (696.6061)—Model 2 Circulating Valve—18 5/8 in. to 20 in. with 41/2-in. IF threads 15

General A straight J-slot is used in the locked-open position so

that the valve can be used with a straight J-slot in the
The Model 2 RTTS Circulating Valve is a locked- packer assembly. This combination eliminates the need
open type of valve that serves as both a circulating to rotate the tubing to close the circulating valve or to
valve and a bypass. It is available for RTTS Packers in reset the packer after the tubing has been displaced
casing sizes ranging from 8 5/8 in. through 20 in. with cement.
The Model 2 RTTS Circulating Valve provides a The calculations of the hydraulic forces of a Model 2
concentric tube-type bypass that is designed to force all RTTS Circulating Valve are the same as those of a
circulated fluid to flow through and around the bottom Champ® Packer. For more information, see the
of the packer. General Hydraulics Manual (SAP No. 100070444;
Legacy No. 696.99993).

September 14, 2001 Page 1 of 18 Section 2b—RTTS Model 2 Circulating Valves

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

Prejob Considerations Lubrication for Sour-Gas Tools

(626.XXXXX and 627.XXXXX series)
Paint and Coating Policy 718 high-nickel alloy threads are very susceptible to
®
All Halliburton Energy Services service tools and galling. A baked-on coating applied in Duncan protects
downhole service tools (DST) should be painted the threads as long as it remains in place. To help
completely red unless: prevent thread galling on sour-gas tools, use one of the
lubricants listed in Table 2b.2
• Customer requirements do not permit paint to be
Table 2b.2—Recommended Lubricants
used. In this case, the tools should have a clear
for Sour-Gas Toolsa
coating.
Part Number Description Quantity
• A special assembly is used. In this case, the bottom
100066644
of the assembly can be painted gray. Such special (626.00001)
Pro-Long Plug grease 40-lb pail
assemblies should be tagged. 100066645
Petrolon S-50 grease 35-lb pail
(626.00002)
• The equipment is used in a sour-gas environment.
100066646
In this case, the equipment should be painted sour- 896 grease 5-gal pail
(626.00003)b
gas green. 100066647
Pro-Long EP2 Plus 1-gal container
(626.00004)
100066648
Paint and Coating Specifications (626.00005)
Petrolon Slick 50 14-oz tube

Halliburton® uses Jones Blair latex paint (HMX 112- a

Petrolon S-50 EP or Molub-Alloy 936 greases can
15D) for the red, gray, and green paint. also be used, but they are not stocked in Duncan.
b896 grease costs about 60% more than Pro-Long
Two clear coatings currently used are Enses K clear
Plug grease or Petrolon S-50 grease.
coating, a Shell product now in use in the Europe-
Africa Region, and Aeroguard W600 clear coating,
which is manufactured by Aero Cote Co. of Houston, Lubrication for Downhole Tools
TX. Aero Cote paint is being tested along the Gulf Pro-Long Plug grease (SAP No. 100066644; Legacy
Coast. Enses K clear coating is not available in the U.S. No. 626.00001) is recommended for general purpose
Table 2b.1 lists paint and coating part numbers. lubrication. It is more expensive than regular greases,
but it may save money over time because it is a high-
quality product for corrosion protection in downhole
Table 2b.1—Paint and Coatings and offshore drilling applications.
for Service and DST Tools
The other lubricants listed in Table 2b.3 have also
Part performed well, especially for use at temperatures
Description
Number
higher than 250°F.
CHEMO-O-PLEX—Jones Blair
100002066
(70.35158) Red downhole tool paint—acrylic latex, water-
Table 2b.3—Recommended Lubricants
reducible for Downhole Tools
CHEM-O-PLEX—Jones Blair
100012961 Part Number Description Quantity
(70.35159) Gray downhole tool paint—acrylic latex, water-
reducible 100066644
Pro-Long Plug grease 40-lb pail
(626.00001)
CHEM-O-PLEX—Jones Blair
100022691 100047822
Sour-gas green downhole tool paint—acrylic Lubri-Plate 930 AA 1-lb can
(70.14131) (130.13049)
latex, water-reducible 100021245
Aeroguard W600—Aero Cote Lubri-Plate 930 AA 14.5-oz carton
100001558 (70.05117)
(70.14132) Clear downhole tool coating 100026246
Litholine No.3 44-gal drum
(70.31233)

Section 2b—Model 2 RTTS Circulating Valves Page 2 of 18 September 14, 2001

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are listed
in parentheses. N/A in place of the SAP number denotes that a
Service Tools Manual
SAP number has not yet been assigned for that part.

Operating Procedures Operating the Model 2 RTTS

Circulating Valve
Note—Consult your local Best Practices Manual for Operating procedures for the Model 2 RTTS Circu-
operating instructions. If no Best Practices Manual is lating Valve are similar to procedures for regular circu-
available, the following instructions can be used as a lating valves; however, the following modifications to
guideline. Location, conditions, and other factors must standard procedures should be made:
be considered when operating the tool.
• After turning to the right and lowering the tubing
when setting the packer, it is unnecessary to
Installing the Model 2 Circulating Valve relieve right-hand torque because the Model 2
on the RTTS Packer Circulating Valve is held closed by tubing pressure
and/or pipe weight.
Follow these steps to install the Model 2 Circulating
Valve on the RTTS Packer: • To open a Model 2 Circulating Valve for spotting,
pick up to tubing weight before starting to circulate
1. Ensure that the lower adapter on the RTTS Packer so that tubing pressure will not resist the opening of
has been replaced with the proper port mandrel, the circulating valve.
which contains internal O-ring seals.
• When unseating the packer for coming out of the
2. Verify that the appropriate lower mandrel hole, it is unnecessary to turn to the right because the
extension is installed on the bottom of the circu- Model 2 Circulating Valve opens with a straight
lating valve. This extension passes completely pull. To lock the bypass open, before moving down-
through the packer and operates in the seals of hole, you must first pick up the workstring and turn
the port mandrel. to the left.
3. Make up the Model 2 RTTS Circulating Valve on
the top of the RTTS Packer. Maintenance Procedure for the
Model 2 RTTS Circulating Valve
The conversion parts that are necessary for use
with each circulating valve are listed in Table See “Maintenance Procedures Manual Section 2b “in
2b.4 (Page 4). the Section 2 Appendix.

Conversion Parts
Table 2b.4 (Page 4) lists the parts required to convert an
RTTS and bypass to a Model 2 RTTS with a concentric
bypass.

September 14, 2001 Page 3 of 18 Section 2b–Model 2 RTTS Circulating Valves

Copyright 1983, 1999, 2001
Halliburton Energy Services® Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

Table 2b.4—Conversion Parts

Model 2 RTTS Packer
Casing Model 2 RTTS Circulating Valve
With Round Hydraulic Slips
Lower Mandrel Overall
Size Weight Assembly Port O-ring Assembly
Mandrel O-ringa Length
(in.) (lb/ft) No. Mandrel (2 required) No.
Extension Extensiona (1 required) (in./mm)

N/A N/A 100001966 N/A N/A 100070249 100002000 129.67

8 5/8 24 to 49
(696.5989) (696.59886) (70.33979) (696.5907) (696.59071) (696.59075) c (70.34026) (3293.6)
100070326 N/A 100001966 N/A N/A 100070249 100002000 129.67
9 5/8 40 to 71.8
(696.6082) (696.59886) (70.33979) (696.5907) (696.59071) (696.59075) c (70.34026) (3293.6)
29.3 to 100070329 N/A 100001966 N/A 100070300 100070290 100002003 132.05
9 5/8
53.5 (696.6083) (696.60881) (70.33979) (696.6019) (696.60216) (696.60189) c (70.34029) (3354.1)
58.4 to N/A N/A 100001966 N/A N/A 100070249 100002000 121.42
9 5/8
71.8 (696.6084) b (696.59886) (70.33979) (696.5907) (696.59071) (696.59075) c (70.34026) (3084.1)
100070350 N/A 100001966 N/A 100070300 100070290 100002003 132.05
10 3/4 32.7 to 51
(696.6093) (696.60881) (70.33979) (696.6019) (696.60216) (696.60189) c (70.34029) (3354.1)
100070350 N/A 100001966 N/A 100070300 100070290 100002003 132.05
10 3/4 55.5 to 81
(696.6097) (696.60881) (70.33979) (696.6019) (696.60216) (696.60189) c (70.34029) (3354.1)
N/A N/A 100001966 N/A 100070300 100070290 100002003 132.05
11 3/4 38 to 47
(696.6211) (696.60881) (70.33979) (696.6019) (696.60216) (696.60189) c (70.34029) (3354.1)
N/A N/A 100001966 N/A 100070300 100070290 100002003 132.05
11 3/4 54 to 65
(696.622) (696.60881) (70.33979) (696.6019) (696.60216) (696.60189) c (70.34029) (3354.1)
100070417 100070424 100001966 N/A 100070309 143.05
13 3/8 48 to 72 — —
(696.6382) (696.63985) (70.33979) (696.6031) (696.60411) (3633.5)
100070421 100070424 100001966 N/A 100070309 143.05
13 3/8 72 to 98 — —
(696.6392) (696.63985) (70.33979) (696.6031) (696.60411) (3633.5)
N/A N/A 100001966 N/A 100070309 N/A 100002003 153.55
16 75 to 109
(696.642) (696.64209) (70.33979) (696.6041) (696.60411) (696.60412) (70.34029) (3900.2)
N/A N/A 100001966 N/A 100070309 N/A 100002003 153.55
18 5/8 78 to 118
(696.652) (696.66209) (70.33979) (696.6061) (696.60411) (696.60412) c (70.34029) (3900.2)
N/A N/A 100001966 N/A N/A N/A 100002003 155.68
20 94 to 133
(696.662) (696.66209) (70.33979) (696.6061) (696.60611) (696.60412) c (70.34029) (3954.3)
5 N/A N/A 100001966 N/A N/A 115.17 5
8 /8 24 to 49 8 /8 24 to 49
(696.5988) b (696.59886) (70.33979) (696.5907) (696.59071) (2925.3)
29.3 to N/A N/A 100001966 N/A N/A 115.17
9 5/8 9 5/8 29.3 to 53.5
53.5 (696.6088) b (696.60881) (70.33979) (696.6019) (696.60211) (2925.3)
5 58.4 to N/A N/A 100001966 N/A N/A 115.17 5
9 /8 9 /8 58.4 to 71.8
71.8 (696.6086) b (696.59886) (70.33979) (696.5907) (696.59071) (2925.3)
32.75 to N/A N/A 100001966 N/A N/A 115.17
10 3/4 10 3/4 32.75 to 51
51 (696.6188) b (696.60881) (70.33979) (696.6019) (696.60211) (2925.3)
3 N/A N/A 100001966 N/A N/A 115.17 3
10 /4 55.5 to 81 10 /4 55.5 to 81
(696.6189) b (696.60881) (70.33979) (696.6019) (696.60211) (2925.3)
N/A N/A 100001966 N/A N/A 115.17
11 3/4 38 to 47 11 3/4 38 to 47
(696.621)b (696.60881) (70.33979) (696.6019) (696.60211) (2925.3)
3 N/A 100070424 100001966 N/A 100070304 119.80 3
13 /8 48 to 72 13 /8 48 to 72
(696.638)b (696.63985) (70.33979) (696.6031) (696.60311) (3042.9)
N/A 100070424 100001966 N/A 100070304 119.80
13 3/8 72 to 98 13 3/8 72 to 98
(696.639)b (696.63985) (70.33979) (696.6031) (696.60311) (3042.9)
a
The mandrel extension is assembled between the lower mandrel and the lower mandrel extension. (Refer to the
Circulating Valve drawing.)
b
These RTTS Packer assemblies are outdated.
cThese parts are included with the Model 2 RTTS Circulating Valve Assembly.

Section 2b—Model 2 RTTS Circulating Valves Page 4 of 18 September 14, 2001

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are listed
in parentheses. N/A in place of the SAP number denotes that a
Service Tools Manual
SAP number has not yet been assigned for that part.

Table 2b.4—Conversion Parts

Casing Pressure-Assist RTTS Packer Model 2 RTTS Circulating Valve
Lower Overall
Size Weight Assembly Port O-ring Assembly Size Weight
Mandrel Length
(in.) (lb/ft) No. Mandrel (2 required) No. (in.) (lb/ft)
Extension (in./mm)
29.3 to N/A N/A 100001966 N/A 100070304 119.80
9 5/8 9 5/8 29.3 to 53.5
53.5 (696.604) b (696.60881) (70.33979) (696.6031) (696.60311) (3042.9)
3 32.75 to N/A N/A 100001966 N/A 100070304 119.80 3 32.75 to
10 /4 10 /4
55.5 (696.614) b (696.60881) (70.33979) (696.6031) (696.60311) (3042.9) 55.5
N/A N/A 100001966 N/A 100070304 119.80
10 3/4 55.5 to 81 10 3/4 55.5 to 81
(696.615) b (696.60881) (70.33979) (696.6031) (696.60311) (3042.9)
3 N/A 100070424 100001966 N/A N/A 119.80 3
13 /8 48 to 72 13 /8 48 to 72
(696.631) b (696.63985) (70.33979) (696.6031) (696.60312) (3042.9)
N/A 100070424 100001966 N/A N/A 119.80
13 3/8 72 -98 13 3/8 72 -98
(696.632) b (696.63985) (70.33979) (696.6031) (696.60312) (3042.9)
aThe mandrel extension is assembled between the lower mandrel and the lower mandrel extension. (Refer to the
Circulating Valve drawing.)
bThese RTTS Packer assemblies are outdated.
cThese parts are included with the Model 2 RTTS Circulating Valve Assembly.

September 14, 2001 Page 5 of 18 Section 2b–Model 2 RTTS Circulating Valves

Copyright 1983, 1999, 2001
Halliburton Energy Services® Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

4 1/2" API internal flush

tool joint thread
6.25" OD
(158.7 mm) 1
11.00“
(279.4 mm) 2

3 13/16" - 10 UNS thread

3.87“ OD
5.50" (98.3 mm) 3
(139.7 mm)
Travel 4
2 15/16" - 6 stub Acme thread
5
2.44" ID
(62.0 mm) 3 3/4" - 10 UNS thread

6.50" OD
(165.1 mm) 6
7
8
4.11" OD
(104.4 mm) 9
10 J-slot
11
115.17" 5.65" ID
(2925.3 mm) (143.5 mm) 12
2 2.40" ID 13 5 15/16" - 6 stub Acme thread
(61.0 mm) 14
3 3/4" - 6 stub Acme thread
32.23" 15
(818.6 mm) 3 9/16" - 12 UNS thread
16

4.13" ID 17
(105.0 mm) 5 15/16" - 6 stub Acme thread

18

2.00" ID
(50.8 mm) 2 1/2" - 10 UNS thread
19

20

4.37"
(111.0 mm) 4 1/2" API internal flush
tool joint thread

21

2 1/2" - 10 UNS thread

22 3

18

23 2

2.40" ID
(61.0 mm)

2.95" OD
(75.0 mm)

SAP No.: N/A Model 2 RTTS Circulating Valve Mandrel OD Areas

Mandrel OD (in.) Mandrel OD Area (in2)
(696.5907)
3.875 11.793
Model 2 RTTS Circulating Valve
Approx. shipping weight: 325 lb
8 5/8 in. with 41/2-in. IF threads

Section 2b—Model 2 RTTS Circulating Valves Page 6 of 18 September 14, 2001

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are listed
in parentheses. N/A in place of the SAP number denotes that a
Service Tools Manual
SAP number has not yet been assigned for that part.

SAP No.: N/A

(696.5907)
Model 2 RTTS Circulating Valve
8 5/8 in. with 41/2-in. IF threads

Part No. Number

# Description
SAP (Legacy) Required
1 100064924 (602.05215) 1 Coupling
2 100001970 (70.33983) 1 O-ring
3 100070295 (696.60195) 1 Lug mandrel
4 100001936 (70.33936) 2 O-ring
5 100002005 (70.34031) 1 O-ring
6 100070293 (696.60193) 1 J-slot sleeve
7 100070297 (696.60197) 1 Lug mandrel extension
8 N/A (696.59073) 1 Upper mandrel
9 100001917 (70.33819) 1 O-ring
10 100001971 (70.33984) 2 O-ring
11 100012949 (70.33993) 2 O-ring
12 100070324 (696.60803) 1 Piston
13 100002008 (70.34034) 1 O-ring
14 100070296 (696.60196) 1 Seal mandrel
15 100004063 (696.61215) 1 Seal
16 100070325 (696.60804) 1 Ring protector
17 100070291 (696.60191) 1 Bypass body
18 100002000 (70.34026) 2 O-ring
19 100070292 (696.60192) 1 Lower body
20 100002017 (70.34047) 1 O-ring
21 N/A (696.59072) 1 Lower mandrel
22 100070249 (696.59075) 1 Mandrel extension (not shown)
23 N/A (696.59071) 1 Lower mandrel extension

# Notes—N/A (696.5907) Data for Steel Components of New Toolsa

1 Optional pickup bail: 100067105 (640.52856) Tensile strength(lb) 271,800
See Table 2b.4 (Page 4) for optional parts and overall Burst (psi) 10,400
2 lengths of various Model 2 Circulating Valves for use Collapse (psi) 10,100
with RTTS Packers. a
The data is valid only for new tools, direct from the
Mandrel extension 100070249 (696.59075) (not shown) manufacturing facility.
is included with the assembly. This part is required
when the Model 2 Circulating Valve is used with the
3 Model 2 RTTS Packer with Round Slips.
One O-ring 100002000 (70.34026) is included with the
assembly and must be used with the mandrel exten-
sion.

September 14, 2001 Page 7 of 18 Section 2b–Model 2 RTTS Circulating Valves

Copyright 1983, 1999, 2001
Halliburton Energy Services® Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

4 1/2" API internal flush tool

joint thread
11.00" 6.25" OD 1
(279.4 mm) (158.7 mm)
2

3 13/16" - 10 UNS thread

3.87" OD
5.50" (98.3 mm)
(139.7 mm) 3 4 5
Travel
2.44" ID
4
(62.0 mm)
2 15/16" - 6 stub Acme thread
5 4 5

6
6.50" OD
(165.1 mm) 3 3/4" - 10 UNS
thread
7
32.23"
(818.6 mm) 8

9
4.11" OD
(104.4 mm) 10
11 J-slot
124.80"
(3169.9 mm) 5.65" ID 12
overall (143.5 mm) 13 5 15/16" - 6 stub Acme thread
length 3 3/4" - 6 stub Acme thread
2 14
2.40" ID
(61.0 mm) 15
3 9/16" - 12 UNS thread
16

4.13" ID
(105.0 mm) 17 5
5 15/16" - 6 stub Acme thread
18

3" - 10 UNS thread

2.40" ID
(61.0 mm)
19

20

4.37" 4 1/2" API internal flush tool

(111.0 mm) joint thread

21

22 3
3" - 10 UNS thread
18

23 2
2.40" ID
(61.0 mm)

2.95" OD
(75.0 mm)

SAP No.: N/ Model 2 RTTS Circulating Valve Mandrel OD Areas

A Mandrel OD (in.) Mandrel OD Area (in2)
(696.6019) 3.875 11.793

Approx. shipping weight: 353 lb Model 2 RTTS Circulating Valve

9 5/8 to 11 3/4 in. with 41/2-in. IF threads
Section 2b—Model 2 RTTS Circulating Valves Page 8 of 18 September 14, 2001
Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are listed
in parentheses. N/A in place of the SAP number denotes that a
Service Tools Manual
SAP number has not yet been assigned for that part.

SAP No.: N/A

(696.6019)
Model 2 RTTS Circulating Valve
9 5/8 to 11 3/4 in. with 41/2-in. IF threads

Part No. Number

Description
SAP (Legacy) Required
1 100064924 (602.05215) 1 Coupling
2 100001970 (70.33983) 1 O-ring
3 100070295 (696.60195) 1 Lug mandrel
4 100001936 (70.33936) 2 O-ring
5 100070293 (696.60193) 1 J-slot sleeve
6 100002005 (70.34031) 1 O-ring
7 100070297 (696.60197) 1 Lug-mandrel extension
8 100070298 (696.60198) 1 Upper mandrel
9 100001917 (70.33819) 1 O-ring
10 100001971 (70.33984) 2 O-ring
11 100012949 (70.33993) 2 O-ring
12 100070324 (696.60803) 1 Piston
13 100002008 (70.34034) 1 O-ring
14 100070296 (696.60196) 1 Seal mandrel
15 100004063 (696.61215) 1 Seal
16 100070325 (696.60804) 1 Protector ring
17 100070291 (696.60191) 1 Bypass body
18 100002003 (70.34029) 2 O-ring
19 100070292 (696.60192) 1 Lower body
20 100002017 (70.34047) 1 O-ring
21 100070299 (696.60199) 1 Lower mandrel
22 100070290 (696.60189) 1 Extension mandrel (not shown)
23 100070300 (696.60216) 1 Lower mandrel extension

# Notes—N/A (696.6019) Data for Steel Components of New Toolsa

Tensile strength (lb) 271,800
1 Optional pickup bail: 100067105 (640.52856)
Burst (psi) 10,400
See Table 2b.4 (Page 5) for optional parts and overall
2 lengths of various Model 2 Circulating Valves for use Collapse (psi) 10,100
with RTTS Packers. a
The data is valid only for new tools, direct from the
Mandrel extension 100070290 (696.60189), which is not manufacturing facility.
shown, is included with the assembly. The mandrel
extension is assembled between Locations 21 and 23
3 when a Model 2 Circulating Valve is used with a Model 2
RTTS Packer with round slips.
The mandrel extension requires one O-ring 100002003
(70.34029), which is included with the assembly.
Optional parts required for running a left-hand J-slot:
4 N/A (696.60214)—lug mandrel
N/A (696.60212)—left-hand J-slot sleeve
Optional parts required to convert from J-slot to straight
spline:
5 100070301 (696.60217)—splined mandrel
100070302 (696.60218)—spline sleeve
100070303 (696.60219)—bypass body

September 14, 2001 Page 9 of 18 Section 2b–Model 2 RTTS Circulating Valves

Copyright 1983, 1999, 2001
Halliburton Energy Services® Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

4 1/2" API internal flush tool

joint thread
11.00" 6.25" OD 1
(279.4 mm) (158.7 mm)
2
3 13/16" - 10 UNS thread

3 4 5
3.87" OD 4
5.50" (98.3 mm)
(139.7 mm) 2 15/16" - 6 stub Acme thread
Travel
2.44" ID 5 4 5
(62.0 mm)
6
3 3/4" - 10 UNS thread

6.50" OD
(165.1 mm)

7
32.23"
(818.6 mm) 8

4.11" OD 9
(104.4 mm)
10
11 J-slot
143.05" 5.65" ID
(3633.5 mm) (143.5 mm) 12
Overall 5 15/16" - 6 stub Acme thread
13
length
3 3/4" - 6 stub Acme thread
2 14
2.40" ID
(61.0 mm) 15
3 9/16" - 12 UNS thread
16

4.13" ID
(105.0 mm) 17 5
5 15/16" - 6 stub Acme thread
18

3" - 10 UNS thread

2.40" ID
(61.0 mm)
19

20

4.37" 4 1/2" API internal flush tool

(111.0 mm) joint thread

21

22 3
3" - 10 UNS thread
18

23 2
2.40" ID
(61.0 mm)

2.95" OD
(75.0 mm)

SAP No.: N/A Model 2 RTTS Circulating Valve Mandrel OD Areas

(696.6031) Mandrel OD (in.) Mandrel OD Area (in2)
Model 2 RTTS Circulating Valve 3.875 11.793
Approx. shipping weight: 353 lb
13 3/8 in. with 41/2-in. IF threads

Section 2b—Model 2 RTTS Circulating Valves Page 10 of 18 September 14, 2001

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are listed
in parentheses. N/A in place of the SAP number denotes that a
Service Tools Manual
SAP number has not yet been assigned for that part.

SAP No.: N/A

(696.6031)
Model 2 RTTS Circulating Valve
13 3/8 in. with 41/2-in. IF threads

Part No. Number

# Description
SAP (Legacy) Required
1 100064924 (602.05215) 1 Coupling
2 100001970 (70.33983) 1 O-ring
3 100070295 (696.60195) 1 Lug mandrel
4 100001936 (70.33936) 2 O-ring
5 100070293 (696.60193) 1 J-slot sleeve
6 100002005 (70.34031) 1 O-ring
7 100070297 (696.60197) 1 Lug mandrel extension
8 100070298 (696.60198) 1 Upper mandrel
9 100001917 (70.33819) 1 O-ring
10 100001971 (70.33984) 2 O-ring
11 100012949 (70.33993) 2 O-ring
12 100070324 (696.60803) 1 Piston
13 100002008 (70.34034) 1 O-ring
14 100070296 (696.60196) 1 Seal mandrel
15 100004063 (696.61215) 1 Seal
16 100070325 (696.60804) 1 Protector ring
17 100070291 (696.60191) 1 Bypass body
18 100002003 (70.34029) 2 O-ring
19 100070292 (696.60192) 1 Lower body
20 100002017 (70.34047) 1 O-ring
21 100070299 (696.60199) 1 Lower mandrel
22 3 1 Extension mandrel (not shown)
23 100070309 696.60411 1 Lower mandrel extension

The tables for N/A (696.6031) are continued on the following page.

September 14, 2001 Page 11 of 18 Section 2b–Model 2 RTTS Circulating Valves

Copyright 1983, 1999, 2001
Halliburton Energy Services® Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

SAP No.: N/A

(696.6031)
Model 2 RTTS Circulating Valve
13 3/8 in. with 41/2-in. IF threads

The tables for N/A (696.6031) are continued from the previous page.

# Notes—N/A (696.6031)

1 Optional pickup bail: 100067105 (640.52856)

See Table 2b.4 (Page 5) for optional parts and overall lengths of various
Model 2 Circulating Valves for use with RTTS Packers.
Lower mandrel extension 100070309 (696.60411) is included with the
2 assembly.
Lower mandrel extension 100070304 (696.60311), which is needed for
outdated RTTS Packers N/A (696.6381) and N/A (696.6391), is not
included with the assembly.
Mandrel extension 100070290 (696.60189), which is not shown, is not
included with the assembly. The mandrel extension is assembled
between Locations 21 and 23 when a Model 2 Circulating Valve is used
3
with a Model 2 RTTS Packer with round slips.
One O-ring 100002003 (70.34029) is included with the assembly and must
be used with the mandrel extension.
Optional parts required for running a left-hand J-slot:
4 N/A (696.60214)—lug mandrel
N/A (696.60212)—left-hand J-slot sleeve
Optional parts required to convert from J-slot to straight spline:
5
100070301 (696.60217)—splined mandrel
100070302 (696.60218)—spline sleeve
100070303 (696.60219)—bypass body

Data for Steel Components of New Toolsa

Tensile strength (lb) 271,800
Burst (psi) 10,700
Collapse (psi) 10,100
a
The data is valid only for new tools, direct from the manufacturing
facility.

Section 2b—Model 2 RTTS Circulating Valves Page 12 of 18 September 14, 2001

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are listed
in parentheses. N/A in place of the SAP number denotes that a
Service Tools Manual
SAP number has not yet been assigned for that part.

4 1/2" API internal flush tool joint thread

11.00" 6.25" OD 1
(279.4 mm) (158.7 mm)
2

3 13/16" - 10 UNS thread

3 4 5
3.87" OD
5.50" (98.3 mm) 4
(139.7 mm)
Travel 2 15/16" - 6 stub Acme thread
2.44" ID
(62.0 mm) 5 4 5
6
3 3/4" - 10 UNS thread

6.50" OD
(165.1 mm)

7
32.23"
(818.6 mm) 8

4.11" OD 9
(104.4 mm) 10
11 J-slot
143.05" 5.65" ID
(3633.5 mm) (143.5 mm) 12
Overall 13 5 15/16" - 6 stub Acme thread
length
3 3/4" - 6 stub Acme thread
2 14
2.40" ID
(61.0 mm) 15
3 9/16" - 12 UNS thread
16

4.13" ID
(105.0 mm) 17 5
5 15/16" - 6 stub Acme thread
18

3" - 10 UNS thread

2.40" ID
(61.0 mm)
19

20

4.37" 4 1/2" API internal flush

(111.0 mm) tool joint thread

21

22 3
3" - 10 UNS thread
18

23 2
2.40" ID
(61.0 mm)

2.95" OD
(75.0 mm)

SAP
No.: N/A
(696.6041)
Approx. shipping weight: Not available Model 2 RTTS Circulating Valve
16 in. with 41/2-in. IF threads
September 14, 2001 Page 13 of 18 Section 2b–Model 2 RTTS Circulating Valves
Copyright 1983, 1999, 2001
Halliburton Energy Services® Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

SAP No.: N/A

(696.6041)
Model 2 RTTS Circulating Valve
16 in. with 41/2-in. IF threads

Part No. Number

# Description
SAP (Legacy) Required
1 100064924 (602.05215) 1 Coupling
2 100001970 (70.33983) 1 O-ring
3 100070295 (696.60195) 1 Lug mandrel
4 100001936 (70.33936) 2 O-ring
5 100070293 (696.60193) 1 J-slot sleeve
6 100002005 (70.34031) 1 O-ring
7 100070297 (696.60197) 1 Lug mandrel extension
8 100070298 (696.60198) 1 Upper mandrel
9 100001917 (70.33819) 1 O-ring
10 100001971 (70.33984) 2 O-ring
11 100012949 (70.33993) 2 O-ring
12 100070324 (696.60803) 1 Piston
13 100002008 (70.34034) 1 O-ring
14 100070296 (696.60196) 1 Seal mandrel
15 100004063 (696.61215) 1 Seal
16 100070325 (696.60804) 1 Protector ring
17 100070291 (696.60191) 1 Bypass body
18 100002003 (70.34029) 2 O-ring
19 100070292 (696.60192) 1 Lower body
20 100002017 (70.34047) 1 O-ring
21 100070299 (696.60199) 1 Lower mandrel
22 1 Extension mandrel (not shown)
23 100070309 (696.60411) 1 Lower mandrel extension

# Notes—N/A (696.6041) Data for Steel Components of New Toolsa

1 Optional pickup bail: 100067105 (640.52856) Tensile strength(lb) 271,800

See Table 2b.4 (Page 5) for optional parts and overall Burst (psi) 10,700
2 lengths of various Model 2 Circulating Valves for use Collapse (psi) 10,100
with RTTS Packers. aThedata is valid only for new tools, direct from the
Mandrel extension N/A (696.60412), which is not manufacturing facility.
shown, is not included with the assembly. The man-
drel extension is assembled between Locations 21
and 23 when a Model 2 Circulating Valve is used with
3
a Model 2 RTTS Packer with round slips.
One O-ring 100002003 (70.34029), which is included
with the assembly, must be used with the mandrel
extension.
Optional parts required for running a left-hand J-slot:
4 N/A (696.60214)—lug mandrel
N/A (696.60212)—left-hand J-slot sleeve
Optional parts required to convert from J-slot to
straight spline:
5 100070301 (696.60217)—splined mandrel
100070302 (696.60218)—spline sleeve
100070303 (696.60219)—bypass body

Section 2b—Model 2 RTTS Circulating Valves Page 14 of 18 September 14, 2001

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are listed
in parentheses. N/A in place of the SAP number denotes that a
Service Tools Manual
SAP number has not yet been assigned for that part.

4 1/2" API internal flush

tool joint thread
11.00" 6.25" OD 1
(279.4 mm) (158.7 mm)
2

3 13/16" - 10 UNS thread

3 4 5
3.87" OD
5.50" (98.3 mm) 4
(139.7 mm)
Travel 5 4 5
2.44" ID
(62.0 mm) 2 15/16" - 6 stub Acme thread
6
3 3/4" - 10 UNS thread

6.50" OD
(165.1 mm)

7
32.23"
(818.6 mm) 8

4.11" OD 9
(104.4 mm)
10
11 J-slot
145.18" 5.65" ID
(3687.6 mm) (143.5 mm) 12
Overall 5 15/16" - 6 stub Acme thread
13
length 3 3/4" - 6 stub Acme thread
2 14
2.40" ID
(61.0 mm) 15
3 9/16" - 12 UNS thread
16

4.13" ID
(105.0 mm) 17 5
5 15/16" - 6 stub Acme thread
18

3" - 10 UNS thread

2.40" ID
(61.0 mm)
19

20

4.37" 4 1/2" API internal flush

(111.0 mm) tool joint thread

21

3" - 10 UNS thread

22 3

18

23 2
2.40" ID
(61.0 mm)

2.95" OD
(75.0 mm)

SAP No.: N/A

(696.6061)
Model 2 RTTS Circulating Valve
Approx. shipping weight: Not available
18 5/8 to 20 in. with 41/2-in. IF threads

September 14, 2001 Page 15 of 18 Section 2b–Model 2 RTTS Circulating Valves

Copyright 1983, 1999, 2001
Halliburton Energy Services® Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

SAP No.: N/A

(696.6061)
Model 2 RTTS Circulating Valve
18 5/8 to 20 in. with 41/2-in. IF threads

Part No. Number

# Description
SAP (Legacy) Required
1 100064924 (602.05215) 1 Coupling
2 100001970 (70.33983) 1 O-ring
3 100070295 (696.60195) 1 Lug mandrel
4 100001936 (70.33936) 2 O-ring
5 100070293 (696.60193) 1 J-slot sleeve
6 100002005 (70.34031) 1 O-ring
7 100070297 (696.60197) 1 Lug mandrel extension
8 100070298 (696.60198) 1 Upper mandrel
9 100001917 (70.33819) 1 O-ring
10 100001971 (70.33984) 2 O-ring
11 100012949 (70.33993) 2 O-ring
12 100070324 (696.60803) 1 Piston
13 100002008 (70.34034) 1 O-ring
14 100070296 (696.60196) 1 Seal mandrel
15 100004063 (696.61215) 1 Seal
16 100070325 (696.60804) 1 Protector ring
17 100070291 (696.60191) 1 Bypass body
18 100002003 (70.34029) 2 O-ring
19 100070292 (696.60192) 1 Lower body
20 100002017 (70.34047) 1 O-ring
21 100070299 (696.60199) 1 Lower mandrel
22 N/A (696.60412) 1 Extension mandrel (not shown)
23 N/A (696.60611) 1 Lower mandrel extension

The tables for N/A (696.6061) are continued on the following page.

Section 2b—Model 2 RTTS Circulating Valves Page 16 of 18 September 14, 2001

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are listed
in parentheses. N/A in place of the SAP number denotes that a
Service Tools Manual
SAP number has not yet been assigned for that part.

SAP No.: N/A

(696.6061)
Model 2 RTTS Circulating Valve
18 5/8 to 20 in.with 41/2-in. IF threads

The tables for N/A (696.6061) are continued from the previous page.

# Notes—N/A (696.6061)

1 Optional pickup bail: 100067105 (640.52856)

See Table 2b.4 (Page 5) for optional parts and overall lengths of vari-
ous Model 2 Circulating Valves for use with RTTS Packers.
2
Lower mandrel extension N/A (696.60611) is included with assembly.
Lower mandrel 100070309 (696.60411) is not included with assembly.
Mandrel extension N/A (696.60412), which is not shown, is included
with the assembly. The mandrel extension is assembled between Loca-
tions 21 and 23 when a Model 2 Circulating Valve is used with a Model
3
2 RTTS Packer with round slips.
One O-ring 100002003 (70.34029) is also included with assembly and
must be used with the mandrel extension.
Optional parts required for running a left-hand J-slot:
4 N/A (696.60214)—lug mandrel
N/A (696.60212)—left-hand J-slot sleeve
Optional parts required to convert from J-slot to straight spline:
5
100070301 (696.60217)—splined mandrel
100070302 (696.60218)—spline sleeve
100070303 (696.60219)—bypass body

Data for Steel Components of New Toolsa

Tensile strength(lb) 271,800
Burst (psi) 10,700
Collapse (psi) 10,100
a
The data is valid only for new tools, direct from the manufacturing
facility.

September 14, 2001 Page 17 of 18 Section 2b–Model 2 RTTS Circulating Valves

Copyright 1983, 1999, 2001
Halliburton Energy Services® Inc.
All rights reserved.
 Note: Where available, SAP numbers are listed first for the parts
and tools in this section. Former (legacy) part numbers are
listed in parentheses. N/A in place of the SAP number denotes
ServiceTools Manual
that a SAP number has not yet been assigned for that part.

This page intentionally left blank.

Section 2b—Model 2 RTTS Circulating Valves Page 18 of 18 September 14, 2001

Copyright 1983, 1999, 2001
Halliburton Energy Services® , Inc.
All rights reserved.