Accessed by UNIVERSITY OF MELBOURNE LIBRARY on 05 Dec 2012 (Document currency not guaranteed when printed)
TABLE Cl (continued) :.
'"
Z
N
Coating system details (See Notes I and 2)
---_._--- - - - - - - - _ . _ - - _ . - . - '"N
lsi Coat
--
2nd Coat 3rd Coat "'N"
System Surface Total nom.
Remarks N
designation preparation lype PRN
I~om
/lm
DFT
Type PRN
Nom.DFT
/lm
Type PRN
Nom.DFT
/lm
DFT, /lm =
=
N
---- r ---
TSA2S0S Sa 2'/, Iprofilc AlumInium -- 25(' Proprietary - Sufficient to - - - 250 -
SO· IUU llnlJ metai spray sealer seal porosity
- - - - - -' - - '
lAPF- -- WrappIng - - - - - - - - - -. Specialist
tapes advice ,huuld
be obtaInc:d
from the tape
manufacturer
Environment: Soil
E1I1I4 Sa 2 y, (profile Ultra high C34 I 200 Ultra high C34 I 20U _.. - - - - 2400 See '\loles 5
75-100 llm) build two· build two- and 6
o pack epoxy pack epoxy
oII -
FBEI Sa 2 y, (profile FuslC'n - 600 - - - - - - 600 See Note 6
-<
::u 75-1 00 ~lIn) bonded ~
Gl epoxv
I
~
TAPE - Wrapplllg - - - - - - - - - Specialist
tapes advice should
be obtained
from the tape
manufacturer
Environment: 1I0t water
IIWEI Sa 2Yo, (profile Hot water - 11)(1 Hot water - 100 Hot water - 100 300 See Notcs 4, 5
30-50 llm) epoxy epoxy epoxy and 6
TSA200P2 Sa 2 Yo, (profi Ie Aluminium ' 200 Butyl U5 Sufficient to - - - 200 --
SO-IOOllm) metal spray titanate seal porosity
(continued)
Accessed by UNIVERSITY OF MELBOURNE. LIBRARY on 05 Dec 2012 (Document currency not guaranteed when printed)
;l>
(FJ
TABLE Dl (continued) 2
"'"
Paint ref. Generic
General description Typical uses and properties
Nominal
volume
Method of
Reference (see Note)
-
'"'"
N
N
e
no. description application e
_. solids, % N
C34 Epoxy ultra Consists of epoxy resin base with As a high p<:rformance, very high-build coating for 90 to 100 Spray only AS 3750.2
high-build adduct or polyamide curing agent. very sevcre conditiuns. appl ied as a single coat or two
APAS 2975
(UHB) May contain some volatile solvent and coals to I 000 to 3 1)00 11m OFT
(2-pack) inert pigments. Limited colours
Has good resistance against water, weather, chemicals
and abrasion. Excellent resistance to cathodic
disbonding. T) picall) us<:d for the protection of
submerged. undergr,)und dnd splash zone surfaces.
Applicabk to steel and concrete structures, including
floors
C35 Butyl titanate Consists of butyl titanate and suitable As a finish coat over inorganic zinc primer for heat 20 Brush, roller -
heat-resistant pigments with volatile resistance to 480°C or spray
o hydrocarbon sol vent
o
IJ
-<
;u
C37 Polysiloxane Consists of catalysed, organic As a high performance, weather, chemical, abrasion 90 Brush, roller, - IV
0\
Cl
modified polysiloxane resin resistant, low surface energy finish. Excellent when preferably
I
used in conjunction with zinc rich primers (CO I, CO2) spray
-I
Application characteristics similar to zinc silicates
T) pically used for protecting the external surfaces of
steel and concrete structures in mild to severe
environmcnls
1\1 C38 Organic zinc Consists of metallic zinc with not less As a single coat. it pro\ ides medium to long term 61 Spray, brush AS 3750.18,
primer (one than 83% llnc 111 the dry film protection for Iron and steel in mild to moderate or roller APAS 2930
pack) moisture dispersed 111 orgal1lc resin-based exposures, and industrial (within pH 6-10 range) to
cure urethane moisture cure polyurethane as a severe marine
(MeU) prepolymet t'O cure as a polyurea
As a primer to be topcoated with a moisture-cured
polvmer. Contains volatile solvents
polyurethane finish (PRN C39 and C40)
Can be applied in high humidity and low temperature
conditions
(continued)
