Safety Data Sheet
according to 29CFR1910/1200 and GHS Rev. 3
Effective date : 12.26.2014 Page 1 of 7
Ammonium Molybdate
SECTION 1 : Identification of the substance/mixture and of the supplier
Product name : Ammonium Molybdate
Manufacturer/Supplier Trade name:
Manufacturer/Supplier Article number: S25171
Recommended uses of the product and uses restrictions on use:
Manufacturer Details:
AquaPhoenix Scientific
9 Barnhart Drive, Hanover, PA 17331
Supplier Details:
Fisher Science Education
15 Jet View Drive, Rochester, NY 14624
Emergency telephone number:
Fisher Science Education Emergency Telephone No.: 800-535-5053
SECTION 2 : Hazards identification
Classification of the substance or mixture:
Irritant
Skin irritation, category 2
Eye irritation, category 2B
Acute toxicity (oral, dermal, inhalation), category 4
Hazards Not Otherwise Classified - Combustible Dust
Acute Tox., oral, 4
Skin Irrit. 2
Eye Irrit. 2
STOT SE 3
Signal word :Warning
Hazard statements:
Harmful if swallowed
Causes skin irritation
Causes serious eye irritation
Harmful in contact with skin
Harmful if inhaled
May cause respiratory irritation
Precautionary statements:
Do not eat, drink or smoke when using this product
Wash … thoroughly after handling
Wear protective gloves/protective clothing/eye protection/face protection
Avoid breathing dust/fume/gas/mist/vapours/spray
Use only outdoors or in a well-ventilated area
Specific treatment (see … on this label)
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do.
Continue rinsing
Call a POISON CENTER or doctor/physician if you feel unwell
Created by Global Safety Management, Inc. -Tel: 1-813-435-5161 - www.gsmsds.com
Safety Data Sheet
according to 29CFR1910/1200 and GHS Rev. 3
Effective date : 12.26.2014 Page 2 of 7
Ammonium Molybdate
Rinse mouth
Take off contaminated clothing and wash before reuse
IF ON SKIN: Wash with soap and water
IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell
If skin irritation occurs: Get medical advice/attention
If eye irritation persists get medical advice/attention
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
Store locked up
Store in a well ventilated place. Keep container tightly closed
Dispose of contents/container to …
Combustible Dust Hazard: :
May form combustible dust concentrations in air (during processing).
Other Non-GHS Classification:
WHMIS
D1B D2B
NFPA/HMIS
NFPA SCALE (0-4) HMIS RATINGS (0-4)
SECTION 3 : Composition/information on ingredients
Ingredients:
CAS 12027-67-7 Ammonium Molybdate 100 %
Percentages are by weight
SECTION 4 : First aid measures
Description of first aid measures
After inhalation: Move exposed individual to fresh air. Loosen clothing as necessary and position individual in
a comfortable position.Seek medical advice if discomfort or irritation persists.If breathing difficult, give oxygen.
After skin contact: Wash affected area with soap and water. Rinse/flush exposed skin gently using water for
15-20 minutes. Seek medical advice if discomfort or irritation persists.
After eye contact: Protect unexposed eye. Rinse/flush exposed eye(s) gently using water for 15-20 minutes.
Remove contact lens(es) if able to do so during rinsing. Seek medical attention if irritation persists or if
concerned.
Created by Global Safety Management, Inc. -Tel: 1-813-435-5161 - www.gsmsds.com
Safety Data Sheet
according to 29CFR1910/1200 and GHS Rev. 3
Effective date : 12.26.2014 Page 3 of 7
Ammonium Molybdate
After swallowing: Rinse mouth thoroughly. Do not induce vomiting. Have exposed individual drink sips of
water. Seek medical attention if irritation, discomfort or vomiting persists.
Most important symptoms and effects, both acute and delayed:
Irritation, Nausea,Headache, Shortness of breath.;
Indication of any immediate medical attention and special treatment needed:
If seeking medical attention, provide SDS document to physician.
SECTION 5 : Firefighting measures
Extinguishing media
Suitable extinguishing agents: If in laboratory setting, follow laboratory fire suppression procedures. Use
appropriate fire suppression agents for adjacent combustible materials or sources of ignition
For safety reasons unsuitable extinguishing agents:
Special hazards arising from the substance or mixture:
Combustion products may include carbon oxides or other toxic vapors.Thermal decomposition can lead to
release of irritating gases and vapors.Avoid generating dust; fine dust dispersed in air in sufficient
concentrations, and in the presence of an ignition source is a potential dust explosion hazard.
Advice for firefighters:
Protective equipment: Use NIOSH-approved respiratory protection/breathing apparatus.
Additional information (precautions): Move product containers away from fire or keep cool with water
spray as a protective measure, where feasible.Use spark-proof tools and explosion-proof equipment.
SECTION 6 : Accidental release measures
Personal precautions, protective equipment and emergency procedures:
Wear protective equipment. Transfer to a disposal or recovery container.Use spark-proof tools and explosion-
proof equipment.Use respiratory protective device against the effects of fumes/dust/aerosol. Ensure adequate
ventilation.Keep away from ignition sources. Protect from heat.Stop the spill, if possible. Contain spilled
material by diking or using inert absorbent.
Environmental precautions:
Prevent from reaching drains, sewer or waterway. Collect contaminated soil for characterization per Section 13
Methods and material for containment and cleaning up:
If in a laboratory setting, follow Chemical Hygiene Plan procedures.Place into properly labeled containers for
recovery or disposal. If necessary, use trained response staff/contractor.Dust deposits should not be allowed to
accumulate on surfaces, as these may form an explosive mixture if they are released into the atmosphere in
sufficient concentration. Avoid dispersal of dust in the air (i.e., clearing dust surfaces with compressed air).
Collect solids in powder form using vacuum with (HEPA filter)
Reference to other sections:
SECTION 7 : Handling and storage
Precautions for safe handling:
Minimize dust generation and accumulation. Wash hands after handling. Avoid dispersal of dust in the air (i.e.,
clearing dust surfaces with compressed air). Routine housekeeping should be instituted to ensure that dusts do
not accumulate on surfaces. Dry powders can build static electricity charges when subjected to the friction of
transfer and mixing operations. Follow good hygiene procedures when handling chemical materials. Do not eat,
drink, smoke, or use personal products when handling chemical substances. Use only in well ventilated
areas.Avoid contact with eyes, skin, and clothing.
Conditions for safe storage, including any incompatibilities:
Created by Global Safety Management, Inc. -Tel: 1-813-435-5161 - www.gsmsds.com
Safety Data Sheet
according to 29CFR1910/1200 and GHS Rev. 3
Effective date : 12.26.2014 Page 4 of 7
Ammonium Molybdate
Provide ventilation for containers. Avoid storage near extreme heat, ignition sources or open flame. Store away
from foodstuffs. Store away from oxidizing agents.Store in cool, dry conditions in well sealed containers. Store
with like hazards
SECTION 8 : Exposure controls/personal protection
Control Parameters: , , OSHA PEL TWA (Total Dust) 15 mg/m3 (50 mppcf*)
, , ACGIH TLV TWA (inhalable particles) 10 mg/m3
Appropriate Engineering controls: Emergency eye wash fountains and safety showers should be available in
the immediate vicinity of use/handling.Provide exhaust ventilation or
other engineering controls to keep the airborne concentrations of vapor
or dusts (total/respirable) below the applicable workplace exposure limits
(Occupational Exposure Limits-OELs) indicated above.Use under a fume
hood. It is recommended that all dust control equipment such as local
exhaust ventilation and material transport systems involved in handling
of this product contain explosion relief vents or an explosion suppression
system or an oxygen deficient environment.Ensure that dust-handling
systems (such as exhaust ducts, dust collectors, vessels, and processing
equipment) are designed in a manner to prevent the escape of dust into
the work area (i.e., there is no leakage from the equipment).
Respiratory protection: Not required under normal conditions of use. Use suitable respiratory
protective device when high concentrations are present. Use suitable
respiratory protective device when aerosol or mist is formed. For spills,
respiratory protection may be advisable.
Protection of skin: The glove material has to be impermeable and resistant to the product/
the substance/ the preparation being used/handled.Selection of the glove
material on consideration of the penetration times, rates of diffusion and
the degradation.
Eye protection: Safety glasses with side shields or goggles.
General hygienic measures: The usual precautionary measures are to be adhered to when handling
chemicals. Keep away from food, beverages and feed sources.
Immediately remove all soiled and contaminated clothing. Wash hands
before breaks and at the end of work. Do not inhale
gases/fumes/dust/mist/vapor/aerosols. Avoid contact with the eyes and
skin.
SECTION 9 : Physical and chemical properties
Appearance (physical Explosion limit lower: Not Determined
White solid
state,color): Explosion limit upper: Not Determined
Odor: Odorless Vapor pressure: Not Determined
Odor threshold: Not Determined Vapor density: Not Determined
5.0 - 5.5 5% aq.
pH-value: Relative density: 2.490
solution
Created by Global Safety Management, Inc. -Tel: 1-813-435-5161 - www.gsmsds.com
Safety Data Sheet
according to 29CFR1910/1200 and GHS Rev. 3
Effective date : 12.26.2014 Page 5 of 7
Ammonium Molybdate
ND = Not Determined. N/A =
Melting/Freezing point: 190C Solubilities: Not Applicable. Material is
water soluble.
Boiling point/Boiling Partition coefficient (n-
Not Determined Not Determined
range: octanol/water):
Flash point (closed Auto/Self-ignition
Not Determined Not Determined
cup): temperature:
Decomposition
Evaporation rate: 2.490 >150C
temperature:
Flammability a. Kinematic:Not Determined
Not Determined Viscosity:
(solid,gaseous): b. Dynamic: Not Determined
Density: Not Determined
SECTION 10 : Stability and reactivity
Reactivity:
Chemical stability:No decomposition if used and stored according to specifications.
Possible hazardous reactions:None under normal processing.
Conditions to avoid:Store away from oxidizing agents, strong acids or bases.Incompatible materials, exposure to
moisture, excess heat, dust formation.
Incompatible materials:Strong acids.Strong oxidizers.
Hazardous decomposition products:Carbon oxides (CO, CO2).Oxides of nitrogen.
SECTION 11 : Toxicological information
Acute Toxicity:
Oral: > 2000 mg/kg bw LD50
Dermal: > 3.92 mg/L air LC50
Inhalation: > 2000 mg/kg bw LD50
Chronic Toxicity: No additional information.
Corrosion Irritation: No additional information.
Sensitization: No additional information.
Single Target Organ (STOT): No additional information.
Numerical Measures: No additional information.
Carcinogenicity: No additional information.
Mutagenicity: No additional information.
Reproductive Toxicity: No additional information.
SECTION 12 : Ecological information
Ecotoxicity
LC50 Fish : . 60 mg/L
Created by Global Safety Management, Inc. -Tel: 1-813-435-5161 - www.gsmsds.com
Safety Data Sheet
according to 29CFR1910/1200 and GHS Rev. 3
Effective date : 12.26.2014 Page 6 of 7
Ammonium Molybdate
Allorchestes compressa , 96 h , LC50 : 247 mg/L
EC10 , Pseudokirchnerella subcapitata: 52.4 mg/L
Persistence and degradability: Readily degradable in the environment.
Bioaccumulative potential:
Mobility in soil:
Other adverse effects:
SECTION 13 : Disposal considerations
Waste disposal recommendations:
Product/containers must not be disposed together with household garbage. Do not allow product to reach
sewage system or open water.It is the responsibility of the waste generator to properly characterize all waste
materials according to applicable regulatory entities (US 40CFR262.11). Consult federal state/ provincial and
local regulations regarding the proper disposal of waste material that may incorporate some amount of this
product.
SECTION 14 : Transport information
UN-Number
Not Regulated
UN proper shipping name
Not Regulated
Transport hazard class(es)
Packing group:Not Regulated
Environmental hazard:
Transport in bulk:
Special precautions for user:
SECTION 15 : Regulatory information
United States (USA)
SARA Section 311/312 (Specific toxic chemical listings):
Acute, Chronic
SARA Section 313 (Specific toxic chemical listings):
None of the ingredients is listed
RCRA (hazardous waste code):
None of the ingredients is listed
TSCA (Toxic Substances Control Act):
All ingredients are listed.
CERCLA (Comprehensive Environmental Response, Compensation, and Liability Act):
None of the ingredients is listed
Proposition 65 (California):
Chemicals known to cause cancer:
None of the ingredients is listed
Chemicals known to cause reproductive toxicity for females:
None of the ingredients is listed
Created by Global Safety Management, Inc. -Tel: 1-813-435-5161 - www.gsmsds.com
Safety Data Sheet
according to 29CFR1910/1200 and GHS Rev. 3
Effective date : 12.26.2014 Page 7 of 7
Ammonium Molybdate
Chemicals known to cause reproductive toxicity for males:
None of the ingredients is listed
Chemicals known to cause developmental toxicity:
None of the ingredients is listed
Canada
Canadian Domestic Substances List (DSL):
All ingredients are listed.
Canadian NPRI Ingredient Disclosure list (limit 0.1%):
None of the ingredients is listed
Canadian NPRI Ingredient Disclosure list (limit 1%):
12077-67-7 Ammonium Molybdate
SECTION 16 : Other information
This product has been classified in accordance with hazard criteria of the Controlled Products Regulations and the
SDS contains all the information required by the Controlled Products Regulations.Note:. The responsibility to
provide a safe workplace remains with the user.The user should consider the health hazards and safety information
contained herein as a guide and should take those precautions required in an individual operation to instruct
employees and develop work practice procedures for a safe work environment.The information contained herein is,
to the best of our knowledge and belief, accurate.However, since the conditions of handling and use are beyond
our control, we make no guarantee of results, and assume no liability for damages incurred by the use of this
material.It is the responsibility of the user to comply with all applicable laws and regulations applicable to this
material.
GHS Full Text Phrases:
Abbreviations and acronyms:
IMDG: International Maritime Code for Dangerous Goods
PNEC: Predicted No-Effect Concentration (REACH)
CFR: Code of Federal Regulations (USA)
SARA: Superfund Amendments and Reauthorization Act (USA)
RCRA: Resource Conservation and Recovery Act (USA)
TSCA: Toxic Substances Control Act (USA)
NPRI: National Pollutant Release Inventory (Canada)
DOT: US Department of Transportation
IATA: International Air Transport Association
GHS: Globally Harmonized System of Classification and Labelling of Chemicals
ACGIH: American Conference of Governmental Industrial Hygienists
CAS: Chemical Abstracts Service (division of the American Chemical Society)
NFPA: National Fire Protection Association (USA)
HMIS: Hazardous Materials Identification System (USA)
WHMIS: Workplace Hazardous Materials Information System (Canada)
DNEL: Derived No-Effect Level (REACH)
Effective date : 12.26.2014
Last updated : 03.19.2015
Created by Global Safety Management, Inc. -Tel: 1-813-435-5161 - www.gsmsds.com
