Technical Bulletin PAGE: 1/2
Reissued: 01-Jul-11
Model: ELP NX Date: 06-Jul-09 No.: RD490002e
RTB Reissue
The items in bold italics have been corrected.
Subject: Release Note: ELP NX Prepared by: T.Nihei
From: 1st Overseas Tech Support Sec., 1st PQM Dept.
Classification: Troubleshooting Part information Action required
Mechanical Electrical Service manual revision
Paper path Transmit/receive Retrofit information
Product Safety Other (Firmware) Tier 2
This RTB has been issued to announce the firmware release information for the ELP NX
(for 4 line LCD models).
Version Program No. Effective Date
1.4.4.0-01 D4901401E May 2011 production
1.4.3.0-01 D4901401D February 2011 production
1.4.1.0-01 D4901401C August 2010 production
1.4.0.0-01 D4901401B April 2010 production
1.3.1.0-01 D4901401A August 2009 production
1.3.0.0-01 D4901401 1st Mass production
Technical Bulletin PAGE: 2/2
Reissued: 01-Jul-11
Model: ELP NX Date: 06-Jul-09 No.: RD490002e
Version Modified Points or Symptom Corrected
1.4.4.0-01 Other changes:
1. Support for Model DI-C1.5(D104/D106) has been added.
Note: Requires the following Java VM firmware versions (or later):
GW Model name VM version
Ver.
07A D017/D018/D019/D020 4.16 or later
D009/D011/D012/D013 4.16 or later
D014/D015 4.16 or later
G179 4.16 or later
D084/D085 4.18 or later
D091/D092 4.18 or later
08S D023/D025 4.16 or later
D027/D029 4.16 or later
D038/D041 4.16 or later
G190 4.16 or later
08A D062/D063/D065/D066 5.05 or later
G188/G189 5.05 or later
09S D067/D068/D069/D072 6.04 or later
M047 5.07 or later
D115/D116 6.07 or later
09A D081/D082 7.01 or later
M065/M066 7.06 or later
D088/D089 7.06 or later
D086/D087 7.06 or later
M022/M024/M026/M028 7.09 or later
D104/D106 7.09 or later
1.4.3.0-01 Other changes:
1. Model S-C4.5(D115/D116) is now supported.
1.4.1.0-01 Other changes:
1. Model Z-P1(M065/M066) is now supported.
1.4.0.0-01 Other changes:
1. Support for Normal Print Jobs.
2. Capital or lower case conversion can be selected.
3. Up to 3 ELP-NX FS can be registered with 1 ELP-NX.
1.3.1.0-01 Symptom corrected:
1. The "Non Locked Print Jobs" setting is returned default value (disable)
after the power cycles though this setting is changed to enable.
1.3.0.0-01 1st Mass production
Effected Models
- S-C4 (D067/D068/D069/D072)
Technical Bulletin PAGE: 1/2
Reissued: 01-Jul-11
Model: ELP NX Date: 06-Jul-09 No.: RD490003d
RTB Reissue
The items in bold italics have been added.
Subject: Release Note: ELP NX Prepared by: T. Nihei
From: 1st Overseas Tech Support Sec., 1st PQM Dept.
Classification: Troubleshooting Part information Action required
Mechanical Electrical Service manual revision
Paper path Transmit/receive Retrofit information
Product Safety Other (Firmware) Tier 2
This RTB has been issued to announce the firmware release information for the ELP NX
( for Printer models).
Version Program No. Effective Date
1.4.4.0-01 D4901701D May 2011 production
1.4.0.0-01 D4901701B April 2010 production
1.3.1.0-01 D4901701A August 2009 production
1.3.0.0-01 D4901701 1st Mass production
Technical Bulletin PAGE: 2/2
Reissued: 01-Jul-11
Model: ELP NX Date: 06-Jul-09 No.: RD490003d
Version Modified Points or Symptom Corrected
1.4.4.0-01 Other changes:
1. Support for Model DI-C1.5(D104/D106) has been added.
Note: Requires the following Java VM firmware versions (or later):
GW Model name VM version
Ver.
07A D017/D018/D019/D020 4.16 or later
D009/D011/D012/D013 4.16 or later
D014/D015 4.16 or later
G179 4.16 or later
D084/D085 4.18 or later
D091/D092 4.18 or later
08S D023/D025 4.16 or later
D027/D029 4.16 or later
D038/D041 4.16 or later
G190 4.16 or later
08A D062/D063/D065/D066 5.05 or later
G188/G189 5.05 or later
09S D067/D068/D069/D072 6.04 or later
M047 5.07 or later
D115/D116 6.07 or later
09A D081/D082 7.01 or later
M065/M066 7.06 or later
D088/D089 7.06 or later
D086/D087 7.06 or later
M022/M024/M026/M028 7.09 or later
D104/D106 7.09 or later
1.4.0.0-01 Other changes:
1. Model Kr-P2(M047) is now supported.
2. Support for Normal Print Jobs.
3. Capital or lower case conversion can be selected.
4. Up to 3 ELP-NX FS can be registered with 1 ELP-NX.
1.3.1.0-01 Symptom corrected:
1. The "Non Locked Print Jobs" setting is returned default value (disable) after
the power cycles though this setting is changed to enable.
1.3.0.0-01 1st Mass production
Effected Models
- Al-P1(G179)
- AP-P2(G188/G189)
- G-P3(G190)
Other changes:
- ELP-NX now supports ELP-NX FS.
- The Card Authentication Package is now optional if using ELP-NX.
- The PS driver can now send Locked Print jobs to ELP-NX.
Technical Bulletin PAGE: 1/2
Reissued: 25-Nov-11
Model: ELP NX Date: 02-Jul-10 No.: RD490004b
RTB Reissue
The items in bold italics have been corrected.
Subject: Release Note: ELP NX update module for Lapnet Prepared by: T. Nihei
From: 2nd Tech Service Sect., MFP/Printer Tech Service Dept.
Classification: Troubleshooting Part information Action required
Mechanical Electrical Service manual revision
Paper path Transmit/receive Retrofit information
Product Safety Other (Firmware) Tier 2
This RTB has been issued to announce the firmware release information for the ELP NX
update module for Lapnet.
Version Program No. Effective Date
1.4.6.0-01 D4905101D November 2011 production
1.4.4.0-01 D4905101B May 2011 production
1.4.0.0-01 D4905101A June 2010 production
1.3.1.0-01 D4905101 June 2010 production
Version Modified Points or Symptom Corrected
1.4.6.0-01 Supported:
Support for the following devices has been added:
Sh-MF1 (M052/M053/M054)
OR-C1 (D120/D121/D122/D139/D140/D141)
Sh-P1 (M020/M021)
S-P3 (M080)
Fixed:
1. ELP-NX displays incorrect messages for the "Printing..." and
"Deleting..." dialog boxes when using a non-English language on a
4-line LCD device.
2. ELP-NX does not close the Deletion Confirmation Dialog if a user
logs out from the device while the Deletion Confirmation Dialog is
being displayed on a 4-line LCD device.
3. Print jobs sent via the dedicated PS driver for some devices are
not stored in the ELP-NX without CAP environment.
Update the Java VM to the latest version before installing this update.
1.4.4.0-01 Other changes:
1. Support for Model DI-C1.5 (D104/D106) has been added.
Technical Bulletin PAGE: 2/2
Reissued: 25-Nov-11
Model: ELP NX Date: 02-Jul-10 No.: RD490004b
Version Modified Points or Symptom Corrected
1.4.0.0-01 Other changes:
1. Model R-C5.5(D084/D085) / Model AL-C1.5(D091/D092) / Model V-C3
(D081/D082) / Model Kr-P2(M047) are now supported.
2. Support for Normal Print Jobs.
3. Capital or lower case conversion can be selected.
4. Up to 3 ELP-NX FS can be registered with 1 ELP-NX.
1.3.1.0-01 Other changes:
1. Model AL-P1(G179) / Model G-P3(G190) / Model AP-P2(G188/G189) /
Model S-C4(D067/D068/D069/D072) are now supported.
2. ELP-NX now supports ELP-NX FS.
3. The Card Authentication Package is now optional if using ELP-NX.
4. The PS driver can now send Locked Print jobs to ELP-NX.
Technical Bulletin PAGE: 1/2
Reissued: 02-Jul-12
Model: ELP NX Date: 19-Nov-08 No.: RD490001k
RTB Reissue
The items in bold italics have been corrected.
Subject: Release Note: ELP NX Prepared by: S. Maruyama
From: 1st Solution Support Sect., Solution Support Dept.
Classification: Troubleshooting Part information Action required
Mechanical Electrical Service manual revision
Paper path Transmit/receive Retrofit information
Product Safety Other (Firmware) Tier 2
This RTB has been issued to announce the firmware release information for the ELP NX.
Version Program No. Effective Date Availability of RFU
1.4.8.0-01 D4900001M June 2012 production Not available
1.4.7.0-01 D4900001L June 2012 production Not available
1.4.6.0-01 D4900001K November 2011 production Not available
1.4.4.0-01 D4900001I May 2011 production Not available
1.4.3.0-01 D4900001H February 2011 production Not available
1.4.2.0-01 D4900001G November 2010 production Not available
1.4.1.0-01 D4900001F August 2010 production Not available
1.4.0.0-01 D4900001E April 2010 production Not available
1.3.1.0-01 D4900001D August 2009 production Not available
1.3.0.0-01 D4900001C July 2009 production Not available
1.2.0.0-01 D4900001B April 2009 production Not available
1.10a D4900001A 1st Mass production Not available
Note: Definition of Availability of RFU via @Remote
“Available” The firmware can be updated via RFU or SD card.
“Not available”: The firmware can only be updated via SD card.
Version Modified Points or Symptom Corrected
1.4.8.0-01 Supported:
Support for the following devices has been added:
MT-C5
GR-C1
S-C5
Update the Java VM to the latest version before installing this update.
1.4.7.0-01 Supported:
Support for the following devices has been added:
AP-C3
AT-C3
AL-C2
1.4.6.0-01 Supported:
Support for the following devices has been added:
Sh-MF1 (M052/M053/M054)
OR-C1 (D120/D121/D122/D139/D140/D141)
Sh-P1 (M020/M021)
S-P3 (M080)
Technical Bulletin PAGE: 2/2
Reissued: 02-Jul-12
Model: ELP NX Date: 19-Nov-08 No.: RD490001k
Version Modified Points or Symptom Corrected
Fixed:
1. ELP-NX displays incorrect messages for the "Printing..." and "Deleting..."
dialog boxes when using a non-English language on a 4-line LCD device.
2. ELP-NX does not close the Deletion Confirmation Dialog if a user logs out
from the device while the Deletion Confirmation Dialog is being displayed
on a 4-line LCD device.
3. Print jobs sent via the dedicated PS driver for some devices are not stored
in the ELP-NX without CAP environment.
1.4.4.0-01 Other changes:
1. Support for Model DI-C1.5 (D104/D106) has been added.
1.4.3.0-01 Other changes:
1. Models Z-C1(M022/M024/M026/M028) and S-C4.5(D115/D116) are now
supported.
1.4.2.0-01 Other changes:
1. Models AT-C2.5(D086/D087) and AP-C2.5(D088/D089) are now supported.
2. Simplified Chinese is now supported.
1.4.1.0-01 Other changes:
1. Model Z-P1(M065/M066) is now supported.
1.4.0.0-01 Other changes:
1. Model R-C5.5(D084/D085) / Model AL-C1.5(D091/D092) / Model V-C3
(D081/D082) / Model Kr-P2(M047) are now supported.
2. Support for Normal Print Jobs.
3. Capital or lower case conversion can be selected.
4. Up to 3 ELP-NX FS can be registered with 1 ELP-NX.
1.3.1.0-01 Symptom corrected:
1. The "Non Locked Print Jobs" setting is returned default value (disable) after
the power cycles though this setting is changed to enable.
1.3.0.0-01 Other changes:
1. Model AL-P1 / Model G-P3 / Model AP-P2 / Model S-C4 are now
supported.
2. ELP-NX now supports ELP-NX FS.
3. The Card Authentication Package is now optional if using ELP-NX.
4. The PS driver can now send Locked Print jobs to ELP-NX.
1.2.0.0-01 Other changes:
1. Model AT-C2 / Model AP-C2 / Model DI-C1 / Model MT-C4 are now
supported.
2. Follow Me Printing is newly supported.
1.10a Other changes:
1. Model R-C5 / Model AL-C1 / Model V-C2 are supported.
2. 1st Mass production
Technical Bulletin PAGE: 1/2
Reissued: 02-Jul-12
Model: ELP NX Date: 02-Jul-10 No.: RD490005d
RTB Reissue
The items in bold italics have been corrected.
Subject: Release Note: ELP NX update module for Activation Prepared by: S. Maruyama
From: 1st Solution Support Sect., Solution Support Dept.
Classification: Troubleshooting Part information Action required
Mechanical Electrical Service manual revision
Paper path Transmit/receive Retrofit information
Product Safety Other (Firmware) Tier 2
This RTB has been issued to announce the firmware release information for the ELP NX
update module for Activation.
Version Program No. Effective Date Availability of RFU
1.4.8.0-01 D4905001E June 2012 production Not available
1.4.7.0-01 D4905001D June 2012 production Not available
1.4.6.0-01 D4905001C November 2011 production Not available
1.4.4.0-01 D4905001A May 2011 production Not available
1.4.0.0-01 D4905001 June 2010 production Not available
Note: Definition of Availability of RFU via @Remote
“Available” The firmware can be updated via RFU or SD card.
“Not available”: The firmware can only be updated via SD card.
Version Modified Points or Symptom Corrected
1.4.8.0-01 Supported:
Support for the following devices has been added:
MT-C5
GR-C1
S-C5
Update the Java VM to the latest version before installing this update.
1.4.7.0-01 Supported:
Support for the following devices has been added:
AP-C3
AT-C3
AL-C2
1.4.6.0-01 Supported:
Support for the following devices has been added:
Sh-MF1 (M052/M053/M054)
OR-C1 (D120/D121/D122/D139/D140/D141)
Sh-P1 (M020/M021)
S-P3 (M080)
Fixed:
1. ELP-NX displays incorrect messages for the "Printing..." and "Deleting..."
dialog boxes when using a non-English language on a 4-line LCD device.
2. ELP-NX does not close the Deletion Confirmation Dialog if a user logs out
Technical Bulletin PAGE: 2/2
Reissued: 02-Jul-12
Model: ELP NX Date: 02-Jul-10 No.: RD490005d
Version Modified Points or Symptom Corrected
from the device while the Deletion Confirmation Dialog is being displayed
on a 4-line LCD device.
3. Print jobs sent via the dedicated PS driver for some devices are not
stored in the ELP-NX without CAP environment.
1.4.4.0-01 Other changes:
1. Support for Model DI-C1.5 (D104/D106) has been added.
1.4.0.0-01 Other changes:
1. Model R-C5.5(D084/D085) / Model AL-C1.5(D091/D092) / Model V-C3
(D081/D082) / Model Kr-P2(M047) are now supported.
2. Support for Normal Print Jobs.
3. Capital or lower case conversion can be selected.
4. Up to 3 ELP-NX FS can be registered with 1 ELP-NX.
