®

DSEULTRA
®

STARTING
WITH
QUALITY. SPECIFICATION

DC SUPPLY

DSE3110 CONTINUOUS VOLTAGE RATING

MANUAL & AUTO START CONTROL MODULE 8V to 35V Continuous

CRANKING DIP PROTECTION

Able to survive 0V for 50mS, providing supply
was at least 10V before dropout and supply
recovers to 5V. This is achieved without the
NEW RELEASE need for internal batteries

CHARGE FAIL/ EXCITATION

8V to 35V fixed power source 2.5W

MAXIMUM SHUTDOWN CURRENT

1.5mA at 12V 1.5mA at 24V

NOMINAL STANDBY CURRENT

23mA at 12V 18mA at 24V

MAXIMUM OPERATING CURRENT

35mA at 12V 30mA at 24V
ELECTRONIC ENGINE CAPABILITY
ALTERNATOR INPUT

RANGE
15V - 333V (L-N) 50Hz - 60Hz
(Minimum 15V AC Ph-N)

ACCURACY
1% of full scale true RMS sensing

MAGNETIC PICKUP

VOLTAGE RANGE
0.5V RMS minimum

FREQUENCY RANGE
10,000 Hz (max)
The DSE3110 can be utilised as a FEATURES OPERATION
Manual or Auto Start Module for • Back-lit LCD display MANUAL MODE OUTPUTS
single gen-set applications and • Remote start input • The engine is started using the
forms part of DSE’s next • Electronic engine enabled Start button on the front of the OUTPUT A (FUEL)
generation of control modules. The • Magnetic pick-up module. 2 Amp DC at supply voltage
module has been designed to work • Full engine monitoring and • Once pressed the module
OUTPUT B (START)
with electronic and non electronic protection instructs the engine to initiate its 2 Amp DC at supply voltage
engines providing advanced • PC programmable pre-heat sequence and then start
• Protected Solid State Outputs the engine. AUXILIARY OUTPUTS C,D
engine monitoring and protection
(PSS) • To stop the engine the Stop 2 Amp DC at supply voltage
features.
• 6 Digital Inputs button on the front of the module
• 4 Outputs (4 configurable on DIMENSIONS
should be pressed.
The DSE3110 includes a backlit Canbus version, 2 configurable on
LCD display which clearly show the Magnetic Pick-up version) AUTOMATIC MODE OVERALL
status of the engine at all times. 98mm x 79mm x 40mm
3.9” x 3.1” x 1.6”
The module monitors engine BENEFITS • The Auto button needs to
speed, frequency, voltage and run • Hours counter provides be pressed to put the unit in Auto PANEL CUT-OUT
hours and also displays the accurate information for 80mm x 68mm
Mode. 3.1” x 2.7”
warning and shutdown status of monitoring maintenance and • The module start sequence is
the engine. warranty periods initiated by the activation of the
• Multiple engine parameters are remote start input.
The module includes six digital monitored simultaneously • The pre-heat sequence is then TESTING STANDARDS
inputs and four outputs. Two of the • Suitable for engine only initiated and the engine is started.
outputs are configurable. The applications • To stop the engine the remote ELECTRICAL SAFETY/
• Module can be configured to suit start signal needs to be removed ELECTROMAGNETIC COMPATIBILITY
module can either be programmed
individual applications or the Stop button on the
using the front panel or by using
• IP65/NEMA 12 rating offers BS EN 61000-6-2
the DSE Configuration Suite PC module needs to be pressed. EMC Generic Emission Standard for the
advanced resistance to water
software. ingress Industrial Environment

• No need for additional metering BS EN 61000-6-4

The module is available in two equipment EMC Generic Emission Standard for the
variants: Magnetic Pick-up and • Wide range of engines can be Industrial Environment
Canbus. specified
• Uses the DSE Configuration Suite
PC Software for simplified
programming
DEEP SEA ELECTRONICS PLC TELEPHONE EMAIL ®
Highfield House +44 (0)1723 890099 sales@deepseaplc.com
Hunmanby Industrial Estate
Hunmanby, North Yorkshire FACSIMILE WEBSITE
YO14 0PH England +44 (0)1723 893303 www.deepseaplc.com

Registered in England & Wales No.01319649 VAT No.316923457

DEEP SEA ELECTRONICS INC TELEPHONE EMAIL

3230 Williams Avenue +1 (815) 316 8706 sales@deepseausa.com
Rockford
IL 61101-2668 USA FACSIMILE WEBSITE
+1 (815) 316 8708 www.deepseausa.com

TESTING STANDARDS
DSE3110
ENVIRONMENTAL

BS EN 60068-2-1
o
Cold Temperature -30 C

BS EN 60068-2-2
o
L1 Hot Temperature +70 C
L2
BS EN 60068-2-6 VIBRATION
L3 Ten sweeps in each of three major axes
FROM
GENERATOR MAG PICK-UP VERSION 5Hz to 8Hz @ +/-7.5mm, 8Hz to 500Hz @ 2gn
N
ONLY
BS 2011 part 2.1 60068-2-30 HUMIDITY
Test Cb Ob Cyclic
2 AMP
FUSES 93% RH @ 40oC for 48 hours

BS EN 60068-2-27 SHOCK
Three shocks in each of three major axes
15gn in 11mS
MPU

DO NOT CONNECT
THE SCREEN TO
ENGINE

ELECTRONIC ENGINE
8 9 10 11
COMPATIBILITY
U N
L1 • CAT
GEN VOLTS USB
• Cummins
MODULE 3110
PROGRAMMING
PORT
• Deutz
• John Deere
CRANK
O/P B
O/P A
FUEL

BATTERY
PLANT +VE PLANT +VE
2 FET OUTPUTS
ENGINE ECU • MTU
6 INPUTS
• Perkins
-VE

+VE

1 2 3 4 7 12 13 14 15 16 17 5 6 10 11
• Scania
• Volvo
• Generic
USER CONFIGURABLE +VE OUTPUT C

USER CONFIGURABLE +VE OUTPUT D

CONNECT THE
SCREEN TO • Plus additional manufacturers
EMERGENCY STOP

USER CONFIGURABLE –VE INPUT E

ENGINE ONLY

RECOMMEND THAT EMERGENCY

USER CONFIGURABLE –VE INPUT B

STOP BREAKS THE FUEL AND

USER CONFIGURABLE –VE INPUT F

CRANK OUTPUTS
MIN 2 AMP MAX 20 AMP
ANIT-SURGE FUSE

USER CONFIGURABLE –VE INPUT C

INPUT A CONFIGURED FOR EM STOP

USER CONFIGURABLE –VE INPUT D

WL
BATTERY

CHARGE
FUEL ALT ELECTRONIC ENGINE
VERSION ONLY

CRANK
NOTE: 120 R TERMINATING RESISTOR MAY
BE REQUIRED EXTERNALLY.
SEE ENGINE MANUFACTURERS LITERATURE

BATTERY NEGATIVE MUST BE GROUNDED

TERMINALS SUITABLE FOR 22-16 AWG (0.6mm - 1.3mm ) FIELD WIRING

TIGHTENING TORQUE = 0.8Nm (7lb-in)

RELATED MATERIALS
TITLE PART NO’S
DSE3110 Installation Instructions 053-050
DSE3110 Manual 057-086
DSE3110 PC Software Manual 057-087

PENDING

DEEP SEA ELECTRONICS maintains a policy of continuous development and reserves the right to
change the details shown on this data sheet without prior notice. The contents are intended for guidance only.

This data sheet is printed on 9lives 55 Silk, which is produced with 55% recycled fibre
from both pre and post-consumer sources, together with 45% virgin ECF fibre.
055-064/07/08 (1)