CENTRIFUGAL PUMP DATA SHEET

1 Note CONSTRUCTION Rev

2 API PUMP TYPE: BB3 [Based on API 610 definitions] CASING MOUNTING: IN-LINE
3 CASING TYPE: (6.3.10) MULTIPLE VOLUTE
4 NOZZLE CONNECTIONS: (6.5.5) OH3 BACKPULLOUT LIFTING DEVICE REQD. (9.1.2.6) NO
5 Size Facing Rating Position CASE PRESSURE RATING:
6 SUCTION 6 RTJ 900 SIDE MAWP : (6.3.6) 1480.00 psig @ 250.00 °F
7 DISCHARGE 3 RTJ 900 SIDE HYDROTEST : 1920 psig @ 250.00 °F
8 PRESSURE CASING AUX. CONNECTIONS: (6.4.3.2)
9 No. Size Type Facing Rating Posn. HYDROTEST OH PUMP AS ASSEMBLY YES
10 BALANCE/LEAK OFF SUCT'N PRESS. REGIONS DESIGNED FOR MAWP YES
11 DRAIN ROTATION: (VIEWED FROM COUPLING END) CW
12 VENT • IMPELLERS INDIVIDUALLY SECURED :
13 PRESSURE GAGE • BOLT OH 3/4/5 PUMP TO PAD / FOUNDATION : NO
14 TEMP GAGE • PROVIDE SOLEPLATE FOR OH 3/4/5 PUMPS NO
15 WARM-UP LINE ROTOR:
16 SHAFT FLEXIBILITY INDEX (SFI) (9.1.1.3)
17 Drain Valve Supplied By SUPPLIER First Critical Speed Wet (Multi stage pumps only) N/A
18 DRAINS MANIFOLDED NO COMPONENT BALANCE TO ISO 1940 G1.0 N/A
19 VENT Valve Supplied By SUPPLIER SHRINK FIT -LIMITED MOVEMENT IMPELLERS (9.2.2.3) N/A
20 VENTS MANIFOLDED
21 THREADED CONS FOR PIPELINE SERVICE & < 50°C (6.4.3.2) COUPLING:(7.2.3) (7.2.13.f)
22 SPECIAL FITTINGS FOR TRANSITIONING (6.4.3.3) MANUFACTURER
23 CYLINDRICAL THREADS REQUIRED (6.4.3.8) MODEL
24 GUSSET SUPPORT REQUIRED RATING (POWER/100 RPM)
25 MACHINED AND STUDDED CONNECTIONS (6.4.3.12) YES SPACER LENGTH in.
26 VS 6 DRAIN SERVICE FACTOR
27 DRAIN TO SKID EDGE RIGID YES
28 COUPLING WITH HYDRAULIC FIT (7.2.10)
29 MATERIAL (6.12.1.1) COUPLING BALANCED TO ISO 1940-1 G6.3 (7.2.3)
30 APPENDIX H CLASS S-6 COUPLING WITH PROPRIETARY CLAMPING DEVICE (7.2.11)
31 MIN DESIGN METAL TEMP (6.12.4.1) °F YES
32 REDUCED-HARDNESS MATERIALS REQ'D (6.12.1.12.1) COUPLING IN COMPLIANCE WITH (7.2.4) mfr std
33 Applicable Hardness Standard (6.12.1.12.3) COUPLING GUARD STANDARD PER (7.2.13.a) ANSI B15.1
34 BARREL : Window on Coupling Guard YES
35 CASE : Carbon Steel
36 DIFFUSERS BASEPLATE

37 IMPELLER : Bronze C93200 API BASEPLATE NUMBER : N/A

38 IMPELLER WEAR RING : GR CA40 BASEPLATE CONSTRUCTION (7.3.14) FULL TOP DECKING
39 CASE WEAR RING : BASEPLATE DRAINAGE (7.3.1) Partial Drain Pan
40 SHAFT: MONEL MOUNTING :
41 Bowl (if VS-type) NON-GROUT CONSTRUCTION : (7.3.13)
42 Inspection Class VERTICAL LEVELING SCREWS :

43 BEARINGS AND LUBRICATION (6.10.1.1) LONGITUDINAL DRIVER POSITIONING SCREWS :

44 BEARING (TYPE / NUMBER): (6.11.4) SUPPLIED WITH : l GROUT AND VENT HOLES
45 RADIAL BALL / l DRAIN CONNECTION
46 THRUST BALL / MOUNTING PADS SIZED FOR BASEPLATE LEVELING (7.3.5) YES
47 REVIEW AND APPROVE THRUST BEARING SIZE : (9.2.5.2.4) MOUNTING PADS TO BE MACHINED (7.3.6) YES
48 PROVIDE SPACER PLATE UNDER ALL EQUIPMENT FEET NO
49 LUBRICATION : (6.10.2.2) (6.11.3) (9.6.1) RING OIL OTHER
50 PRESSURE LUBE SYSTEM TO ISO 10438- (9.2.6.5) Production Solution Standard Base plate
50 ISO 10438 DATA SHEETS ATTACHED
51 Pressurized Lube Oil System mtd on pump baseplate REMARKS :
52 Location of Pressurized Lube Oil System mounted on baseplate : Production Solution Standard Base plate
53
54 INTERCONNECTING PIPING PROVIDED BY Supplier
55
56 OIL VISC. ISO GRADE VG 68
57 CONSTANT LEVEL OILER :
A

DATA SHEET No. Rev: B SHEET 3 of 10