Spool Valve:

J, H, S, T, and W Series
Disc Valve: 2,000, 4,000 Compact, Delta,
4,000, 6,000, and 10,000 Series
Low Speed, High Torque Motors VIS: VIS 40, and VIS 45 Series
2000 Series Two-Speed Note:
This is the low speed biased motor circuit. For the high
Typical Hydraulic Circuit speed biased motor motor circuit please contact your Eaton
Hydraulics representative.

Pump Pressure and Return, and

Shaft Rotation Directional Control Valv e

Pilot Pressure 6,9 Bar [100 PSI] Min.

Check Valve s

Two Position Three Way Valv e

LSHT HS LT

Pilot Port Pilot Port

Port A Port B Port A Port B

Restriction 14 Bar [200 PSI]

and Check Valv e

Case Drain
(Option) C-1

Output
Shaft
2000 Series Two Spee d
Motor — Motor
Two Spee d Schematic

Optional Shuttle
Valve Locatio n

Case Drain Case Drain (Option) Case Drain

Pilot Port
Port A Port B

Case Drain
(Option)
Low Speed Maximum System
High Torque Horsepower Curve
Two Spee d
Motor
Schematic
with... Output
Torqu e

Shaft

High Speed ...Optional Two

Low Torqu e Way Shuttle Valv e

Case Drain

Speed - RPM
2 - Speed Operating Range

EATON Low Speed High Torque Motors E-MOLO-MC001-E9 October 2018 C-1-27
2000 Series Two-Speed
Specifications

SPECIFICATION DATA — 2000 SERIES TWO-SPEED MOTORS

Displ. cm3/r [in3/r] High Speed Mode 40 [2.45] 50 [3.1] 65 [4.0] 80 [4.8] 95 [5.95] 120 [7.45] 155 [9.35] 195 [12.0] 245 [14.9]
Low Speed Mode 80 [4.9] 100 [6.2] 130 [8.0] 160 [9.6] 195 [11.9] 245 [14.9] 305 [18.7] 395 [24.0] 490 [29.8]
Max. Speed High Speed Mode 1000 1000 990 860 700 560 450 350 230
(RPM) Low Speed Mode 500 500 495 430 350 280 225 175 115
@ Continuous Flow
Flow l/min [GPM]
High Speed Mode 45 [12] 55 [15] 70 [19] 75 [20] 75 [20] 75 [20] 75 [20] 75 [20] 75 [20]
Low Speed Mode 45 [12] 55 [15] 70 [19] 75 [20] 75 [20] 75 [20] 75 [20] 75 [20] 75 [20]
Torque* High Speed Mode
Nm Continuous 100 [880] 125 [1115] 165 [1450] 195 [1725] 240 [2150] 300 [2675] 380 [3350] 365 [3225] 448 [3970]
[lb-in] Intermittent 145 [1300] 185 [1660] 240 [2150] 240 [2150] 300 [2650] 375 [3330] 440 [3900] 445 [3940] 486 [4300]
Torque* Low Speed Mode
Nm Continuous 235 [2065] 295 [2630] 385 [3420] 455 [4040] 540 [4780] 660 [5850] 765 [6750] 775 [6840] 845 [7470]
[lb-in] Intermittent 345 [3035] 445 [3950] 560 [4970] 570 [5040] 665 [5890] 820 [7250] 885 [7820] 925 [8170] 930 [8225]
Pressure Continuous 205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 155 [2250] 120 [1750]
∆ bar [∆ PSI] Intermittent 310 [4500] 310 [4500] 310 [4500] 260 [3750] 260 [3750] 260 [3750] 240 [3500] 190 [2750] 140 [2000]
Weight Standard or 13,8 [30.5] 14,1 [31.0] 14,3 [31.5] 14,5 [32.0] 15,0 [33.0] 15,4 [34.0] 15,9 [35.0] 16,3 [36.0] 16,8 [37.0]
kg [lb] Wheel Mount
Bearingless 11.8 [26.0] 12,0 [26.5] 12,2 [27.0] 12,5 [27.5] 12.9 [28.5] 13,4 [29.5] 13,8 [30.5] 14,3 [31.5] 14,7 [32.5]
Maximum Case Pressure: See case pressure seal limitation graph.
*See shaft torque ratings for limitations.

Note: High Speed Mode ∆ bar [∆ PSI] : Recommended Fluids:

To assure best motor life, (Reduced Motor The true pressure difference Premium quality, anti-wear
run motor for approximately Displacement) between inlet port and type hydraulic oil with a
one hour at 30% of rated outlet port viscosity of not less than 70
pressure before application Low Speed Mode SUS at operating tempera-
to full load. Be sure motor is (Full Motor Displacement) Continuous Rating: ture.
filled with fluid prior to any Motor may be run continu-
load applications. Maximum Inlet Pressure: ously at these ratings Recommended System
Operating Temp.:
310 bar [4500 PSI]
Intermittent Operation: -34°C to 82°C [-30°F to
Do not exceed ∆ pressure 180°F]
rating (see chart above). 10% of every minute

Peak Operation: Recommended Filtration:

Maximum Return Pressure:
1% of every minute per ISO Cleanliness Code,
310 bar [4500 PSI] with case 4406: 20/18/13
drain line installed.
Do not exceed ∆ pressure
rating (see chart above).

C-1-28 EATON Low Speed High Torque Motors E-MOLO-MC001-E9 October 2018
 Ports
2000 Series Two-Speed 7/8 -14 UNF-2B SAE O-ring Staggered Ports (2)
9/16 -18 UNF-2B SAE O-ring Case Drain Port (1)
Dimensions 7/16 -20 UNF-2B SAE O-ring Pilot Control Port (1) or
Standard and Wheel G 1/2 (BSP) Staggered Ports (2)
G 1/4 (BSP) Case Drain Port (1)
G 1/4 (BSP) Pilot Control Port (1)
Standard Rotation Viewed from Shaft End
Port A Pressurized — CW
Port B Pressurized — CCW

Two-Speed Standard Motors STANDARD MOUNT MOTOR DIMENSIONS

Displacement X Y
Port B cm3/r [in3/r] mm [inch] mm [inch]
80 [4.9] 137,4 [5.41] 231,6 [9.12]
Y Max.
100 [6.2] 142,0 [5.59] 236,5 [9.31]
X 130 [8.0] 148,5 [5.85] 242,9 [9.56]
160 [9.6] 148,5 [5.85] 242,9 [9.56]
195 [11.9] 155,2 [6.11] 249,4 [9.82]
245 [14.9] 164,2 [6.47] 258,6 [10.18]
305 [18.7] 175,7 [6.92] 270,1 [10.63]
395 [24.0] 191,5 [7.54] 286,1 [11.26]
490 [29.8] 209,0 [8.23] 303,3 [11.94]

C-1

Two-Speed Wheel Motors WHEEL MOUNT MOTOR DIMENSIONS

Displacement X Y
cm3/r [in3/r] mm [inch] mm [inch]
Port B
80 [4.9] 97,2 [3.83] 191,5 [7.54]
Y Max.
100 [6.2] 101,8 [4.01] 196,4 [7.73]
X 130 [8.0] 108,3 [4.27] 202,7 [7.98]
160 [9.6] 108,3 [4.27] 202,7 [7.98]
195 [11.9 115,0 [4.53] 209,3 [8.24]
245 [14.9] 124,2 [4.89] 218,5 [8.60]
305 [18.7] 135,5 [5.34] 229,9 [9.05]
395 [24.0] 151,4 [5.96] 245,9 [9.68]
490 [29.8] 168,9 [6.65] 263,1 [10.36]

EATON Low Speed High Torque Motors E-MOLO-MC001-E9 October 2018 C-1-29
2000 Series Two-Speed Ports
7/8 -14 UNF-2B SAE O-ring Staggered Ports (2)
9/16 -18 UNF-2B SAE O-ring Case Drain Port (1)
Dimensions
7/16 -20 UNF-2B SAE O-ring Pilot Control Port (1) or
Bearingless G 1/2 (BSP) Staggered Ports (2)
G 1/4 (BSP) Case Drain Port (1)
G 1/4 (BSP) Pilot Control Port (1)
Standard Rotation Viewed from Shaft End
Port A Pressurized — CW
Port B Pressurized — CCW
Two-Speed
Bearingless Motors 17,3/15,7
41,7/40,8 [.68/.62]
[1.64/1.61] 61,9/60,8
[2.44/2.39]
27,7/26,1
[1.09/1.03] 31,0/30,2
[1.22/1.19]
14,0/12,9 3/8-24 UNF 26,5/25,4
[.55/.51] 15,8[.62] Dp. (4) [1.04/1.00]
20,6/19,5 8,7/7,8
[.81/.77] [.34/.31]
7/16-20 UNF-2B O-ring Port — Pilot Control
24,2/23,3 Pilot Port Pressurized 6,9 D Bar [100 D PSI]
[.95/.92] Port A High Speed Low Torque (HSLT)
Pilot Port Depressurized (Tank)
Port B Low Speed High Torque (LSHT)
37,9/36,8
[1.49/1.45]
Optional
Case Drain
10,7/9,6
[.42/.38] 45,5/44,4
64,3/62,7 [1.79/1.75]
[2.53/2.47] 66,1/65,0
[2.60/2.56]

Port B
122,0 [4.80] Max. 3,1 [.12] Max. Y Max.
68,1 X
[2.68] Max.

74,0/72,8
[2.91/2.87]

63,0
[2.48]
Max.
6,4/5,8
[.25/.23]
46,0/44,9
[1.81/1.77]
9/16-18
UNF O-ring
Case Drain
BEARINGLESS MOTOR DIMENSIONS
Port
Displacement X Y
cm3/r [in3/r] mm [inch] mm [inch]
80 [4.9] 79,3 [3.13] 174,0 [6.85]
100 [6.2] 84,1 [3.31] 178,9 [7.04]
130 [8.0] 90,7 [3.57] 185,2 [7.29]
160 [9.6] 90,7 [3.57] 185,2 [7.29]
195 [11.9] 97,3 [3.83] 191,8 [7.55]
245 [14.9] 106,4 [4.19] 201,0 [7.91]
305 [18.7] 117,8 [4.64] 212,4 [8.36]
395 [24.0] 133,6 [5.26] 228,4 [8.99]
490 [29.8] 151,1 [5.95] 245,6 [9.67]

C-1-30 EATON Low Speed High Torque Motors E-MOLO-MC001-E9 October 2018
2000 Series Two-Speed Note:
For 2000 Series Motors with
Use digit prefix —
193- plus four digit number
a configuration Not Shown from charts for complete
Product Numbers product number—Example
in the charts below, contact
your Eaton Representative. 193-0002.
Orders will not be accepted
without three digit prefix.

MOUNTING SHAFT PORT SIZE DISPL. cm3/r [in3/r] / PRODUCT NUMBER

80 100 130 160 195 245 305 395 490
[4.9] [6.2] [8.0] [9.6] [11.9] [14.9] [18.7] [24.0] [29.8]
7/8 -14 O-ring
1 Inch Straight Staggered 193-0002-001 -0003 -0004 -0005 -0006 -0007 -0008 -0009 —
2 Bolt
SAE A 7/8 -14 O-ring
1 1/4 Inch Straight Staggered 193-0010-001 -0011 -0012 -0013 -0014 -0015 -0016 -0017 -0070
Flange
1 1/4 Inch 7/8 -14 O-ring
14 T Splined Staggered 193-0018-001 -0019 -0020 -0021 -0022 -0023 -0024 -0025 —
7/8 -14 O-ring
Wheel
1 1/4 Inch Tapered Staggered 193-0222-001 -0223 -0224 -0225 -0226 -0227 -0228 -0229 —
Motor 1 1/4 Inch 7/8 -14 O-ring
14 T Splined Staggered 193-0230-001 -0231 -0232 -0233 -0234 -0235 -0236 -0237 —
7/8 -14 O-ring
Bearingless Staggered 193-0282-001 -0283 -0234 -0285 -0286 -0287 -0288 -0289 —

193-0288-001
C-1

EATON Low Speed High Torque Motors E-MOLO-MC001-E9 October 2018 C-1-31
2000 Series The following 30-digit coding system has been developed to identify all of the configura-
tion options for the 2000 Series motor. Use this model code to specify a motor with the
desired features. All 30 digits of the code must be present when ordering. You may want to
Two-Speed photocopy the matrix below to ensure that each number is entered in the correct box.

Model Code (193-)

M 2 2 * * * * * * * * * * * * * 1 * * * 0 0 * * * * A A A

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Shaft with .375-16UNC-2B

1 Product Thread in End, 7.938 [.3125] Sq 19 Seal Option
M – Motor x 31.75 [1.250] Straight Key 00 – Standard Seals
03 – 31.75 [1.250] Dia. .125:1 02 – S
 eal Guard
2 , 3 Series Tapered Shaft per SAE J501 03 – Viton Seals
22 – 2000 2 Speed Series with/1.000-20 UNEF-2A
(1:2 Ratio) Threaded Shaft End and 04 – Viton Shaft Seal
Slotted Hex Nut, 7.938 [.3125] 11 – High pressure shaft
4 , 5 , 6 Displacement Sq x 25.40 [1.0] Straight Key seal, slinger seal
049 – 80.6 cm3/r [4.92 in3/r] 04 – 31.75 [1.250] Dia. Flat 19 – Extreme duty seal
062 – 101.6 cm3/r [6.20 in3/r] Root Side Fit, 14 Tooth, 12/24 guard
080 – 130.6 cm3/r [7.97 in3/r] DP 30° Involute Spline w/
096 – 158.1 cm3/r [9.65 in3/r] .375-16UNC-2B Thread in End, 20 , 21 Accessories
119 – 194.8 cm3/r [11.89 in3/r] 33.0 [1.30] Min. Full Spline 00 – NONE
149 – 244.3 cm3/r [14.91 in3/r]
187 – 306.6 cm3/r [18.71 in3/r] 22 , 23 Special Features
240 – 393.8 cm3/r [24.03 in3/r 11 , 12 Ports Description (Hardware)
298 – 489.0 cm3/r [29.84 in3/r] AA – .875-14 UNF-2B SAE 00 – NONE
7 , 8 Mounting O-ring Ports - Staggered Ports
Description AB –12.70 [.500] and 15.88 24 , 25 Special Features
AB – Wheel, 4 Bolt: 108.0 [.625] Dia. Manifold Ports with (Assembly)
[4.25] Pilot Dia. 13.59 [.535] 3 x .375-16 UNC-2B Port Block 00 – NONE
Dia. Holes on 147.6 [5.81] Dia. Mounting Holes
Bolt Circle. 127.0 [5.00] Dia. 26 , 27 Paint / Packaging
Rear Mount Pilot 13 , 14 Case Flow Options /
AA – No Paint, Individual Box
AC – Standard, 2 Bolt: 82.6 Selector Valve
AB – Low Gloss Black Primer,
[3.25] Pilot Dia. 13.59 [.535] 01 – .5625-10 UNF-2B SAE
Individual Box
Dia. Holes on 106.4 [4.19] Dia. O-Ring Case Drain Port,
Bolt Circle. SAE A .4375-20 UNF-2B SAE O-Ring
28 , 29 Customer
AE – Bearingless (w/ Leakage Pilot Control Port, Optional
.4375-20 UNF-2B SAE Case Identification
Slots), 4 Bolt: 101.6 [4.00]
Drain Port for Pilot Operated AA – NONE
Pilot Dia. 13.59 [.535] Dia.
Holes on 127.0 [5.00] Dia. Bolt Normally Low Speed
30 Design Code
Circle
15 Shuttle Valve / Low A – FIRST
AF – Standard, 2 Bolt: 101.6
[4.00] Pilot Dia. 14.35 [.565] Pressure Relief
Dia. Holes on 146.0 [5.75] Dia. 0 – NONE
Bolt Circle. SAE B
Dia Bolt Circle (European) 16 , 17 Pressure / Flow
Option
9 , 10 Output Shaft 00 – NONE
Description
00 – None (Bearingless) 18 Geroler Option
01 – 25.40 [1.000] Dia. Straight 1 – STANDARD
Shaft with 1/4-20UNC-2B
Thread in End, 6.35 [.250]
Wide x 25.40 [1.000] Dia.
Woodruff Key
02 – 31.75 [1.250] Dia. Straight

C-1-32 EATON Low Speed High Torque Motors E-MOLO-MC001-E9 October 2018