Product Data Sheet
Edition 01/01/2014
Identification no:
02 07 06 03 001 0 000016
®
Sikagard -694 F(I)
Sikagard®-694 F (I)
Moisture insensitive epoxy putty
Product ®
Sikagard -694 F (I) is a solvent free epoxy resin based putty like material. It has the
Description special property that it is a moisture insensitive repair material
Construction
®
Uses Sikagard -694 F(I) is recommended for :
Sealing of cracks both underwater and in dry conditions
Sealing of cracks for concrete, metal and wooden surfaces
Protection of concrete, steel, marine structures as protective coating at or below
the water line
Characteristics / Forms excellent bond on damp, dry and underwater surfaces
Advantages Stops the ingress of water
Excellent resistance to saline environment
Eliminates corrosion of steel and concrete structures even in marine condition
Excellent impact resistance
Good mechanical properties
Product Data
Form
Colours Part A: white
Part B: black
Part A+B mixed: grey
Packaging 8 kg (A+B) Pre-Batched unit
Part A: 4.00 kg plastic container
Part B: 4.00 kg plastic container
Pot Life 100 g mass (According to FIP 5.1)
~ 50 min at 30ºC
Storage
Storage Conditions / 12 months from date of production if stored properly in original unopened, sealed
Shelf-Life and undamaged packaging, in dry conditions at temperatures between +5°C and
+30°C. Protect from direct sunshine.
Technical Data
Chemical Base Epoxy resin.
1 ®
Sikagard -694 F(I) 1/3
Mixed Density ~ 1.55 kg/l
All density values at +27 ºC
Mechanical / Physical
Properties
Compressive Strength (According ASTM C579 )
Curing time +30°C
2
1 day >20 N/mm
2
3 days >25 N/mm
Product cured and tested at temperatures indicated.
Test specimen size: 50 * 50 * 50mm
Bond Strength On dry concrete: (According to EN 1542)
Curing temperature
Curing time + 30°C
3 day >2.5 N/mm²
Slant Shear on dry concrete: (According to ASTM C882)
Curing temperature
Curing time + 30°C
3 day >10 N/mm²
Application Details
Substrate Quality All surface must be clean and free from loose particles, laitance, grease, oil, marine
growth, etc.
Substrate Preparation The surface should be prepared using the required tools.
Application
Conditions /
Limitations
Substrate Temperature +5°C min. / +40°C max.
Ambient Temperature +5°C min. / +40°C max.
®
Material Temperature Sikagard -694 F(I) must be at a temperatures of between +10°C and +40°C for
application.
Application
Instructions
Mixing Part A : Part B = 1 : 1 (by weight)
Mixing Time Pre-batched units:
Mix parts A+B together for at least 3 minutes with a mixing
spindle attached to a slow speed electric drill
(max. 600 rpm) until the material becomes smooth in
consistency and a uniform grey colour. Avoid aeration
while mixing. Then, pour the whole mix into a clean
container and stir again for approx. 1 more minute at low
speed to keep air entrapment at a minimum. Mix only that
quantity which can be used within its potlife.
Application Method / Apply the mixed material using glove-protected hand, spatula or trowel and work
Tools well on to the property prepared substrate. The surface of the applied material can
be smoothened by slight rubbing with wet gloves.
®
Cleaning of Tools Clean all tools and application equipment with Sika Colma Cleaner immediately
after use. Hardened / cured material can only be mechanically removed.
2 ®
2/3
Sikagard -694 F(I)
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Health and Safety For information and advice on the safe handling, storage and disposal of chemical
products, users shall refer to the most recent Material Safety Data Sheet containing
Information physical, ecological, toxicological and other safety-related data.
Legal Notes The information, and, in particular, the recommendations relating to the application
and end-use of Sika products, are given in good faith based on Sika's current
knowledge and experience of the products when properly stored, handled and
applied under normal conditions in accordance with Sika’s recommendations. In
practice, the differences in materials, substrates and actual site conditions are such
that no warranty in respect of merchantability or of fitness for a particular purpose,
nor any liability arising out of any legal relationship whatsoever, can be inferred
either from this information, or from any written recommendations, or from any other
advice offered. The user of the product must test the product’s suitability for the
intended application and purpose. Sika reserves the right to change the properties
Construction
of its products. The proprietary rights of third parties must be observed. All orders
are accepted subject to our current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product Data Sheet for the product
concerned, copies of which will be supplied on request.
Sika India Pvt. Ltd. Phone +91 33 2447 2448/2449
Commercial Complex II Telefax +91 33 2468 8688/2665
620, Diamond Harbour Road www. sika.in
Kolkata, 700 034, India info@in.sika.com
3 ®
3/3
Sikagard -694 F(I)
