· i - Sense technology

(if the skin teamperature probe

detached from the baby skin,
the device automatically
sense and reduce the heater
output to 30%)

FLEXIBLE OPTIONS
COMFORTABLE FUNCTIONS

Neotech
Technical Specification
Infant Radiant Warmer
Features:
· Micro Controller based Electronics
· Controls: Skin/Air /Apgar and Manual
· Pre-warm: Use the equipment with 30% Heater Output
in Manual Mode.
· i - Sense technology
· No need of calibration required for temperature probe.
(if the skin teamperature probe
· High Intensity Quartz Heating element for effective
detached from the baby skin,
Radiation (Ceramic heater Optional)
the device automatically
· Halogen Observation Lamp
sense and reduce the heater
· The Heater Module rotates 90° to both sides to facilitate
output to 30%)
X-Ray Procedures.
· The Parabolic Reflector is designed to send uniform heat
to the bed surface.
· Memory Backup to restore set temperature and
previous mode, in case of power failure.
· Optimum Bed dimensions ensure optimum work space
for the nursing staff.
· Comprehensive Alarms and safety cut-offs.
· Programmable Mute time.
· Alert (Alarm) when sensor is detached from the
patient's skin(optional)
· Instant Warming and Uniform heating.
Optional (height Adjustment)
Main voltage : AC 230V/ 50 Hz. Apgar Timer : Alerts at 1,5,10,15 and 20 minutes
Max. power requirement : 700VA Selectable
Supply current : Maximum 3.2 Amps CPR Timer : 1 - 59 minutes selectable
Examination light : 50 W / 12 V AC Halogen lamp Heating element : Quartz IR heater(Standard)

Electronics : Highspeed Micro controller With self Mattress tilt : +/- 15 degrees
test function Heater Module Swivel : ±90° to the side to facilitate X -ray
Modes of operation : Servo Skin, Servo Air and Manual procedure
Castors : 4 Nos 4” (Antistatic with 2 brakes)
Controller Heating Alarms Heater watts : 600 VA
Skin Temp High : + 1 0 C from the2 set point
Skin Temp Low : - 1 0 C from the set point X-Ray cassette tray : 57cm (L) X 35cm (W)
Air Temp High : + 1 0 C from the set point IV pole : Maximum load : 1.5kg
Air Temp Low : - 1 0 C from the set point Monitor Tray : Swivel & Fixed Type Maximum Load
Over temperature : > 39 0 C ( Skin/Air) 2.5Kg
Probe failure : Short (or) Open circuit / No probe IEC 60601-1 Specification
System failure : Indicates system fail Type of protection against electric shock : Class 1
Heater failure : If heater fail Degree of protection against electric shock : Type BF (skin probe)
Power failure : AC power interruption Type B (Mattress)
Mode of Operation : Continuous
Alarm silence / Reset Intervals Protection against Hazardous of Explosion : Not Protected
Check patient : Resets clock for Every 15 minutes Protection against increases of liquid : Not Protected
(manual mode) MDD Product Classification : Class llb
Alarm silience :10 minutes
Controller Environmental
Skin set temp range : 32 - 380 C Operating Temperature : 100 C to 300 C
Air set temp range : 30 - 380 C Operating Relative Humidity : 15 to 90% RH non condensing
Heater output : 5% - 100%, 5% increments Storage Temperature : -100 C to 600 C
Skin/Air temp display : 10 - 50 0 C Storage Relative Humidity : 50 to 90% RH non condensing
Resolution : 0.1 0 C Altitude : Sea level to 1.9 miles (3 kms)
Accuracy : +/- 0.2 0 C (300 C to 50 0 C)
Temperature Conversion : Centigrade/Fahrenheit Dimensions
74-00-011, Rev 01

Temperature Calibration : No need of calibration Equipment : 192 cm (H) X 109 cm(L) X 68 c(W)
Skin probe : Thermistor based interchangeable Mattress : 73 cm (L) X 53 (W) cm X 5 cm (H)
with accuracy +/- 0.2 0 C Weight : 81 kgs
Air probe : Thermistor based interchangeable with
accuracy +/- 0.2 0 C Quality/Test approval
Noise level : < 50db Quality : ISO 13485:2016
Thermostat : Auto Reset 90 0 C +/- 5 0 C for infant Electrical safety : IEC 60601-1
warmer : IEC 60601-2-21
Control panel lock : Lock key provided EMC Safety : IEC 60601-1-2

Manual Mode : System alerts every set manual time

15 minutes with heater cutoff
. . .
Neotech

AN ISO 13485:2016 Company(with design)

Regd.Office & Factory:# 85 Krishna Industrial Estate, Mettukuppam,

Vanagaram, Chennai - 600 095 India
Tel:+91-44-24762594,+91-44-24764608 Fax: +91-44-24766920,
e-mail info@niceneotech.com Web: www.niceneotech.com