Is:800-1984

( Rerfflrmed 1998
( Reaffirmed 2003) )

Indian Standard
CODE OF PRACTICE FOR

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
GENERAL CONSTRUCTION, IN STEEL

( First Revision )
Sixtcmtb Reprint MAY WI!3
(IncorporatingAmendments No. 1 and 2)

UDC 693814 : 006-76

8 Copyright 1995

BUREAU OF INDIAN STANDARDS

MANAK BHAVAN, 9 BAHADUR SHAH ZAPAR MARG
NEW DELHI- 110002

Gr 15 February, 1985
b
-

18:soo-1981

Indian Standard
CODE OF PRACTICE FOR
GENERAL CONSTRUCTION IN STEEL

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
( Second Revision)
Structural Engineering Sectional Committee, SMBDC 7

Chairman Rejraanting
DIREOTOBSTAHDAIGDS (Cm) Ministry of Railwaya
Members
SEBI R M. AGABWAL Institution of Engineers ( India ), Calcutta
Da Pa= ~ISEXA (Alimuf~ )
SEEI 0. P. bA2?D Central Water Commission, New Delhi
Srrnr V. NABAYANAEI ( Altmatr )
Smt~ A. K. BANEEJ~B Metallurgical & Engineering Consultants ( India )
Ltd, Ranchi
Sass S. SANKlsAZ4 ( Alternate )
SHRI P. G. BARDHAN Braithwaite & Co Ltd, Calcutta
Srrnr S. K. GANQOPADHYAY ( Altarnets)
SHBI S. N. BAEU Inspection Wing, Directorate General of Supplies
& Disposals, New Delhi
SHRI D. B. JAIN ( Affrrnafe )
SHBT P. C. BHA+N Ministry of Shipping & Transport ( Department
of Transport ) ( Roads Wing )
DR P. DAYARATNAX Indian Institute of Technology, Kanpur
SHRI D. S. DESAI M. N. Dastur & Co Pvt Ltd, Calcutta
SHRI S. R. KULKARNI ( Altmnutc )
DIRECTOR ( TRANSMISSION ) Central Electricity Authority, New Delhi
DEPUTY DIREOTOR
( TRANSA~ISSION) ( AIturnata)
JOINT DIREOTOR S T AN D A B D s Ministry of Railways
(B&S)
ASSISTANT DIRECTOR
STANDARDS ( B & S )-SB ( Alternate )
JOINT DIRECTOR ( DEBIONS ) National Building Organization, New Delhi
SERI K. S. SR~HIVASAN (Alternate )

( Continued on page 2 )

0 Copyright 1995
BUREAU OF INDIAN STANDARDS
Thir publication is protected under the Indian Copyright Act ( XIV of 1957 ) and
reproduction in whole or in part by any meane except with written permissionof the
publisher shall te deemed to be an infringement of copyright under the said'Act. 1
 l8:809-1984

( ,Co&inued from page 1 )

Members Ro@wnfing
DR J. N. KAR Government of West Bengal
SHRI KARTIK PRASAD Indian Roads Congress, New Delhi
SRRI S. P. CHAKRABA~~~ ( Altsrnnfr )

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
SHRI N. K. MAJUMDAB Hindustan Steel Works Construction Ltd,
Calcutta
SH~I P. K. MALLICK Jessop & Co Ltd, Calcutta
SHRI T. S. BA~CHI ( AIfernufe )
SHRI S. K. MUKEERJEE Bridge & Roof Co ( India ) Ltd, Howrah
SHRI B. K. CHATTERJEE ( Alfernafe )
SERI P. V. NAIK Richardson & Cruddas Ltd, Bombay
SHRI V.-G. MANORULKAR ( Alfernnfe )
SHRI DILIP PAVL Industrial Fasteners Association of Indim
Calcutta
i SHRI H. C. PARYESWA~AN Engineer-in-Chief’s Branch, Army Headquarters
SFIRI N. C. JAIN ( AItnnafr)
SERI N., RADHAKRISH~AN Binny Ltd. Madras
Sara1 P; APPARAO ( Alfekfe ) .
SHRI N. y. RADIAN , Struc$arax$gineering Research Centre ( CSIR ),

DR ‘ph’V. S. R. APP~ RAO ( Affernafe 1

SHPI M. %:‘RANCSA RAO Tats Consulting Engineers, New Delhi
SXRI~:A. S. BIJVRK AR ( Alternote )
SH~I A. B. RIBE~O Rail India Technical & Economic Services,
New Delhi
SHRI S. K. BHANOT ( Alfcrnafe)
SHRI P. SEN~UPTA Stewarts & Lloyds of India Ltd, C&utta
SRRI M. M. GHO~H ( Alfemafe )
SERI M. M. SHENOY Joint Plant Committee, Calcutta
SBRI D. SRINIVASAN ( Alternate )
SaxuC. N. SRINIVASAN Messrs C. R. Narayanan Rao, Madras
SHRI Cl. N. RA~EAVENDRAN ( AIfcrnafe)
SHRK M. SRIHARIVARDA RAJ Bharat Heavy Electricals Ltd. Tiruchchirapalli
SHRI A. K. MITTAL ( Alfernafe )
S,ERI H.?K. TANEJA Indian Register of Shipping, Bombay
SHR~ D. SARAN~DEAR ( Alfernafe )
SEBI M:D. THAIUBEKAR Bombay Port Trust, Bombay
University of Roorkee, Roorkee
Engineers India Ltd, New Delhi

Director General, BIS ( Ex-~&io Membrr )

Secretary
SERI S. S. SETHI
Deputy Director ( Strut & Met ), BIS

( Confinued on page 3 )

2
( Confinm#f*omPogr 2 )

Subcommittee for Use of Structural Steel in General

Building Constructim, SMBDC 7 : 2

Convener Rethsettting

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
SHRI A. CHELLAY Ministry of Railways
Members
SHRI A. K. BAN~ZJX~ Metallurgical & Engineering Consultants ( India )
Ltd. Ranchi
SHRI S. SANKARAN( Alternate)
SHRI P. G. BARDHAN Braithwaite & Co Ltd, Calcutta
SHRI S. K. GAN~OPADEYAY ( Altanatr )
Da P. N. CHATTERJEE Bengal Engine&n College, Howrah
SHRI S. K. DATTA Richardson & CN $ daa Ltd, Bombay
SHRI D. S. DESAI M. N. Dastur k Co Pvt Ltd, Calcutta
SHRI G. B. JAHA~IRDAR The National Industrial Development Corpora-
tion Ltd, New Delhi
DR A. K. JAIN University of Roorkee, Roorkee
SHRI K. C. KARAMCHAF~ANI Engineers India Ltd, New Delhi
SHRI B. B. NAP ( Altcrnata )
Snnr P. K. MALLICK Jesrop & Co Ltd, Calcutta
SHRI P. R. NATARAJAN Structural Engineering Research Centre (CSIR),
Madras
DR T. V. S. R. A~PARAO ( Alternate)
SHRI T. K. RAXANATHAN Triveni Structurals Ltd, Allahabad
Snn~ M. N. PAUL ( Alternate )
SHRI Y. C. RAO The Tata Iron & Steel Co Ltd, Jamshedpur
SHRI K. S. RANUANTHAN ( Aflernatc )
REPRESENTATIVE Engineer-in-Chief’s Branch, Army Headquarters
REPRESENTATIVE Burn Standard Co Ltd, Howrah
S-1 P. R. BH~WMIO Steel Authority of India Ltd ( Bokaro Steel
PIant ), Bokaro Steel City
SHRI N. K. CHAXRAVORTY ( Altcrnafs )
PROF P. K. SOM Government of West Bengal, Calcutta
SHRI C. N. SRINIVASAN Meson C. R. Narayana Rao, Madras
SHRI K. VEERARAQHAVACHARY Bharat Heavy Electricals Ltd, Tiruchchirapalli
SHRI A. K. MITTAL ( Altcrnuts )
ISrsoo-MS4

CONTENTS

PALE

0. FOREWORD . . . .. . . .. . .. .. . ... 11

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
SECTION 1 GENERAL

1.1 SC@qPE ... ... ... ... ... ... 13

1.2. TE~INOLOOY .., ... ... . .. . .. 13
1.3 !hfBOLS ... . .. ... ... . .. ‘... 14
1.4 REFERENCETO OTHER STANDARDS ... . .. *.. 17
1.5 UNITS AND CONVERSIONFACTORS ... ... ... 20
1.6 STANDARDDIMENSIONS,FORM AND WEIGHT .. . ... 20
1.7 PLANS AND DRAWINGS. . . ... ... . .. ... 20

SECTION 2 MATERIALS
2.1 STRUCTURALSTEEL ... . .. .. . . l .. ..I 21
2.2 RIVETS ... ... ... ... ... . . .
21
2.3 WELDING CONSUMABLES ... ... ... . . .
21
2.4 STEEL CASTINGS .:. . .. ... ... . . . 22
2.5 BOLTS AND Nuts ... ... .. . _. . . . 22
2.6 WAsHERs ... ... ... ... ... . . . 22
2.7 CEMENTCONCRETE ... ... _. ... . . . 22
2.8 OTHER MATERIALS ... ... ... ... . . . 22

SECTION 3 GENERAL DESIGN REQUIREMiNTS

3.1 TYPES OF LOADS ... ... ... ... ... 22

3.2 ERECTIONLOADS ... ... ... ... ... 23
3.3 TEMPERATUREEFFECTS ... ... ... ... 23
3.4 DESIQN CONSIDERATIONS ... ... ... ... 23
3.4.1 General .__ ... ... ... .. , ... 23
3.4.2 Load Combinations ... ... ... ... 24
3.4.3 Methods of Design ... ... ... ... 25
3.4.4 Simple Design .. . ... ... ... ... 25
3.4.5 Semi-rigid Design ... ... ... ... 25
3.4.6 Fully Rigid Design ... ... ... ... 25
3.4.7 Experimentally Based Design ... . .. .-. 26

4
 1s I 900 - 19&4

PAQE
3.5 GEOMETRICAL PROPERTIES ............ 26
3.5.1 General ... ............... 26
3.5.2 Plate Thickness ............... 27
3.6 HOLES ...... ............ 28

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
3.6.1 Diameter ................ 28
3.6.2 Deduction for Holes ...... ...... 28
3.7 MAXIMUMSLENDERNESSRATIO ............. 30
3.8 CORROSIONPRoTEaTroN - MINIMUMTHICKNESSOF METAL 30
3.8.1 General .................. 30
3.8.2 Steelwork Directly Exposed to. Weather ...... 30
3.8.3 Steelwork Not Directly Exposed to Weather ...... 30
3.8.4 Rolled Steel.Be’ams and Channels ...... ... 31
3.9 INGREA~EOF STRESSES...... r........ 31
3.9.1 General .................. 31
3.9.2 Increase in Permissible Stresses in Members Proportioned
for Occasional Loadings ............ 31
3.9.3 Increase in Permissible Stresses for Design of Gantry
Girders and Their Supporting Structures ...... 31
3.10 FLUCTUATIONOF STRESSES ............. 32
3.11 RESISTANCE TO HORIZONTALFORCES .......... 33
3.12 STABILITY. ...... ......... ... 34
3.13 LIMITINO DIWLBCTION ............ 34
3.14 EXPANSIONJOINTS ....... ......... 35

SECTION 4 DESIGN OF TENSION MEMBERS

4.1 AXIAL STRE%¶ ............... 37
4.2 DESIGNDETAILS ...... ......... 37
4.2.1 Net Effective Areas for Angles and Tees in Tension ... 37
SECTION 5 DESIGN OF COMPRESSION MEMBERS
5.1 IXXIALSTRESSES
IN UNCASED STRUTS ... ....... 38
5.2 EFFECTIVELEN~TI-IOF COMPRESSIONMEMBERS ... ... 38
5.2.1 General . . . .,. .,. ... ... ... 38
5.2.2 Effective Length . . . ... ... ... ... 40
5.2.3 Eccentric Beam Connections ... ... . .. 40
5.2.4 Members of Trusses ... . ,, ... ... 40
5.2.5 Stepped Columns ... ... . .. ... 40

..
Is : 688 - 1984

PAQE

5.3 DESIGNDETAILS .. . ... ... .. . . .. 40

5.3.1 Thickness of Elements ,. . .. . .. . .. 40
5.3.2 Effective Sectional Area _.. . .. ... ... 40
5.3.3 Eccentricity for Stanchion and Solid Columns . .. 40

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
5.3.4 Splices . ..- .. . . .. ... . .. .. . 43
5.4 COLUMNBASES .. . ... ... .. . . .. 44
5.4.1 Gusseted Bases _.. .__ . .. .. . . .. 44
5.4.2 Column and Base Plate Connections ... .. . 44
5.4.3 Slab Bases _.. _.. ... . .. . .. 44
5.4.4 Base Plates and Bearing Plates . .. ... . .. 46
5.5 ANISE STRUTS _,_ _.. . .. . .. . .. 46
5.5.1 Single Angle Struts _.. .. . ... . .. 46
5.5.2 Double Angie Struts .__ ... .. . ... 46
5.5.3 Continuous Members _.. . .. ... ... 47
5.5.4 Combined Stresses _.. ... . .. . .. 47
5.6 STEEL CASTINGS ___ ... ... ... ... 47
5.7 LACING ... . .. . .. ... . .. ... 47
5.7.1 General . .. ... ... . .. ... 47
5.7.2 Design of Lacing __. ... . .. ... ... 48
5.7.3 Width of Lacing Bars ... ... ... . .. 50
5.7.4 Thickness of Lacing Bars . . . ... ... . .. 50
5.7.5 Angle of Inclination __. . .. .-. . .. 51
5.7.6 Spacing ... . .. ... ... .. . 51
5.7.7 Attachment to Main Members ... .. . ... 51
5.7.8 End Tie Plates .._ ... ... ... .. . 51
5.8 BATTENINGAND TIE PLATES . . . ...
... . .. 51
5.8.1 General ... .. . .. .
... . .. 51
5.8.2 Design . .. ... .. .
... ... 53
5.8.3 Spacing of Battens ... ...
... ..i 54
5.8.4 Attachment to Main Members .. .
... ..I
54
5.9 COMPRESSIONMEMBERS COMPOSED OF COMPONENTS
Two
BACK-TO-BACK ... _.. . .. ...
... 54
SECTION 6 DESIGN OF MEMBERS
SUBJECT&D TO BENDING
6.1 GENERAL ... ... ... ... . .. .n 55
6.2 BENDINGSTRESSES . . . ... .,. . .. .., 55
6.2.1 Maximum Bending Stresses ... . .. . .. 55
6
 1s : 800 - 1984

PAGE
6.2.2 Maximum Permissible Bending Compressive Stress in
Beams and Channels with Equal Flanges ... . .. 55
6.2.3 Maximum Permissible Bending Compressive Stress in
Beams and Plate Girders . . . ... .,, ... 56

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
6.2.4 Elastic Critical Stress . .. ... ... ... 63
6.2.5 Beams Bent About the Axis of Minimum Strength (~9 Axis ) 68
6.2.6 Angles and Tees . . . . .. ... . .. .. . 68
6.3 BEARINGSTRESS . .. . .. ... .. . . .. 68
6.4 SHEARSTRESSES .. . .. . ... ..: . .. 68
6.4.1 Maximum Shear Stress .,. ... . .. I..
68
6.4.2 Average Shear Stress . . . . . . . . . .
69 . .

6.5 EFFECTIVESPAN OF BEAMS ... ... ... 76

. . .

6.6 EFFECTIVELENGTHOF COMPRESSION FLANGES . .. . . .

76
6.7 DESIGNOF BEAMSANDPLATE GIRDERSWITH SOLIDWEBS . . .
80
6.7.1 Sectional Properties . .. ... ... . . .
80
6.7.2 Flanges . .. ... . .. .f. . . .
80
6.7.3 Web Plates ... ... ... ... . . .
.81
6.7.4 Intermediate Web Stiffeners for Plate Girders . . .
84
6.7.5 Load Bearing Web Stiffeners ... ... . . .
87
6.8 Box GIRDERS . .. . .. .. . .. . . . . 88
6.9 PURLINS “._ . .. . .. . . . . .. .a.
89
6.10 SIDE ANDEND SHEETINGRAILS .,. . .. a..
89

SECTION 7 COMBINED STRESSES

7.1 COMBINATIONOF DIRECT STRESSES .. . .., .*.
90
7.1.1 Combined Axial Compression and Bending , . . . . .
90
7.J.2 Combined Axial Tension and Bending . .. . . .
90
7.1.3 Symbols . .. ... ... ... . . .
90
7.1.4 Bending and Shear .. . .. ... . . .
91
7.1.5 Combined, Bearing, Bending and Shear Stresses . . . 92
SECTION 8 CONNECTIONS
8.0 GENERAL . . . ... ... . .. . .. . . . ’ 92
8.1 RIVETS, CLOSETOLERANCEBOLTS,HIQH STRENGTHFRICTION
GRIP FASTENERS,BLACKBOLTSANDWELDING ... ._. 92
a.2 CO~~POSITECONNECTIONS .,. . . . . . . .. . 92
8.3 MEMBERSMEETINGAT A JOINT ... ,.. . .. 93

.
IS t 888 - 1984

8.4 BEARINGBRACKETS . . . ... ... .. . ... 93

8.5 GussETs ... . .. ... ... .. . ... 93
8.6 PACKINGS . . . . ., . .. . .. . .. ... 93

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
8.7 SEPARATORS
AND DIAPHRAGMS._. ... . .. .. . 94
8.8 LUG ANoLEs . . . . .. . .. . .. .*. . .. 94
8.9 PERMISSIBLESTRESSES
IN RIVETSAND BOLTS . .. . .. 94
8.9.1 Calculation of Stresses ... ... ... . .. 94
8.9.2 Gross and Net Areas of Rivets and Bolts ... ... 95
8.9.3 Areas of Rivets and Bolt Holes . .. ... 95
8.9.4 Stresses in Rivets, Bolts and Welds 1:: ... ... 95
8.10 RIVETS AND RIVETING ... . .. . .. . .. 96
8.10.1 Pitch of Rivets . . . ... . .. .. . ... 96
8.10.2 Edge Distance . . . . .. ... ... ... 97
8.10.3 Tacking Rivets . . . . .. ... . .. .. . 97
8.10.4 Countersunk Heads ... . .. .. . . .. 98
8.10.5 Long Grip Rivets ... ... ... ... ?8
8.11 BOLTSAND BOLTING . . . ... . .. ... . .. 98
8.11.1 Pitches, Edge Distances for Tacking Bolts . .. .. . 98
8.11.2 Black Bolts ... ... ... ... .. . 98
8.11.3 Close Tolerance Bolts ... ... . .. ... 98
8.11.4 Turned Barrel Bolts ... ... . .. ... 98
8.11.5 ‘Washers .. . ... ... ... .. . 98
8.11.6 Locking of Nuts . . . ... ... ... .. . 98
8.12 WELDSAND WELDING ... ... . .. ... 98

SECTION 9 PLASTIC DESIGN

9.1 GENERAL .. . .,. ... ... ... . .. 99
9.2 DESIGN .. . .., ... ... ... ... 99
9.2.1 Load Factors .. . ... ... ... ... 99
9.2.2 Deflection ... ... ... ... .. . 99
9.2.3 Beams ... ... ... ... ... 99
9.2.4 Tension Members ... ... ... ... ioo
9.2.5 Struts .. . ... .*. ... ... . .. 100
9.2.6 Members Subjected to Combined Bending, and Al&d
Forces ( Beam-Column Members ) . .. ._ ... 100
9.2.7 Shear . . . ... .. . ... . .. . .. 101

8
 PAQE

9.2.8 Stability.. ............. .. . 101

9.2.9 Minimum Thiekneas ......... . .. 102
9.2.10 Lateral Bracing ........... ... . .. 103

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
9.2.11 Web Stiffening ... ._ ...... A.. 104
9.2.12 Load Capacitiesof Connections ...... . .. 105
9.3 CONNECTIONS ANDFABRICATION ...... ... 105
9.3.1 Connections ............ ... 105
9.3.2 Fabrication ............ ... 105

SECTION 10 DESIGN OF ENCASED MEMBERS

10.1 ENCASEDCOLUMNS ............... 105
10.1 .l Conditions of Design ............. 105
10.1.2 Design of Member ............ 106
10.2 ENCASED BEAMS ... 1.. ......... 107
10.2.1 Conditions of Design ............ 107
10.2.2 Design of Member ............ 107

SECTION 11 FABRICATION AND ERECTION

11.1 GENERAL .................. 108
11.2 FABRICATION PROCEDURIS ............ 108
11.2.1 Straightening ............... 108
11.2.2 Clearances ............... 108
11.2.3 Cutting ............... 108
11.2.4 Holing .................. 108
11.3 &SEMBLY ............... _. 109
11.4 RIVETING .................. 109
11.5 BOLTING .................. 110
11.6 WELDING ................ ... 110
11.7 MACHININQOFBUTTS,CAPSANDBASES......... 110
11.8 SOLIDROUNDSTEELCOLUMNS ......... 111
11.9 BArNTrNo .................. 111
11.10 MARKING.................. 112
11.11 SHOPERECTION ............... 112
11.12 PACKING .................. 112
ANDTESTLNO ............
11.13 INSPECTION 112

9
IS t 800- 1984

PAGE

11.14 SITE ERECTION ... ... ... . .. ... 113

11.14.1 Plant and Equipment ... ... ... .. . 113
11.14.2 Storing and Handling ,.. . .. ... . .. 113

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
il.14.3 Setting Out ... ... ... ... *.. 113
11.14.4 Security During Erection ... ... ... 113
Il. 14.5 Field Connections ... ... ... ... 114
11.15 PAINTING AFTER ERECTION . . . .. . . .. . .. 114
11.16 BEDDING OF STANCHION BASES AND BEARINGS OF BEAMS AND
GIRDERS ON STONE, BRICK OR CONCRETE ( PLAIN OR
REINFORCED ) ... .. . .. . ... ... 114

SECTION ii STEELWORK TENDERS

AND CONTRACTS

12.1 GENERAL RECOMMENDATIONS 115

APPENDICES
APPENDIX A CHART SHOWING HIGHEST MAXIMUM TEMPERATURE 116
APPENDIX B CHART SHOWING LOWEST MINIMUM TEMPERATURE 117
APPENDIX C EFFECTIVE LENGTH OF COLUMNS . .. . .. 118
APPENDIX D METHOD FOR DETERMINING EFFECTIVE LENGTH FOR
STEPPED COLUMNS .. . .. . ,.. ... 120
APPENDIX E .LIST OF REFERENCES ON THE ELASTIC FLEXURAL
TORSIONAL BUCKLING OF STEEL BEAMS . . . .. . 131
APPENDIX F PLASTIC PROPERTIES OF INDIAN STANDARD MEDIUM
WEIGHT BEAMS [ IS : 808 ( Part 1 )-I973 } ... 132
APPENDIX G GENERAL RECOMMENDATIONS FOR STEELWORK
TENDERS AND CONTRACTS ... .. . . .. 133

10
 ISt800-1984

Indian Standard
CODE OF PRACTICE FOR
GENERAL CONSTRUCTION IN STEEL

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
( Second Revision )

0. FOREWORD

0.1 This Indian Standard ( Second Revision) was adopted by the Indian
Standards Institution on 25 April 1984, after the draft finalized by the
Structural Engineering Sectional Committee had been approved by the
Structural and Metal Division Council and the Civil Engineering Division
couucil.

0.2 The Steel Economy Programme was initiatedbyIS1 in 1950’s with the
object of achieving economy in the use of structural steel by establishing
rational, efficient and optimum standards for structural steel products and
their use. IS : 800-1956 was the first in the series of Indian Standards
brought out under this programme. The revision of this standard was
taken up after the standard was in use .for some time which was published
in 1962 incorporating certain very important changes.

0.3 IS : 800 is a basic standard widely used and accepted by engineers,

technical institutions, professional bodies and the industry. The committee
while preparing the second revision has given careful consideration tb the
comments received on the standard during its usage. Consideration has also
been given to the developments taking place in the country and abroad;
necessary modifications and additions have therefore been incorporated to
make the standard more useful.

0.4 In this revision the following major modifications have been effected:

a>Besides a general rearrangement of the clauses,

values have been given’in SI units only.
formulae and the

b) Symbols used in this standard have been aligned to the extent

possible with IS0 3898-1976 ‘ Basis for design of structures -
Notation - General symbols ‘, and these have been listed in 1.3.
4 All the Indian Standards referred to in this Code have been listed
under 1.4.

11
1s t 800 - 1984

d) In view of the development and production of new varieties of

medium and high tensile structural steels in the country, the
scope of the Code has been modified permitting the use of any
variety of structural steel provided the relevant provisions of the
Code are satisfied.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
e>Indian Standards are now available for rivets, bolts and other
fasteners and reference has been made to these standards.
f >In view of the fact that the Code specifies a number of grades of
steel with different yield strengths, the design parameter, the
geometrical properties and permissible stresses have been express-
ed to the extent possible in terms of the yield strength of the
material. Specific values have also been given for commonly
used steels.
g) Recommendations regarding expansion joints have been added.
h) Keeping in view the developments in the design of steel struc-
tures there has been a general revision in the permissible stress
values for steels and fasteners.
j> In IS : 800-1962, design by plastic theory had been permitted. In
this revision detailed design rules have been included for design
using plastic theory.
k) Specific provisions relating to limiting deflection have been
added.
m) Effective length of columns has been dealt with in a greater
detail. For normally encountered struts, a table has been given
strictly on the basis of end conditions. The effective length of
columns in framed structures and stepped columns in mill build-
ings have been specified on more exact basis.
4 The secant formula for axial compression has been dropped. In
its place the Merchant Rankine formula has been specified with
value of a, empirically fixed as 1.4.
P) Bending stresses - The method of calculating the critical stresses
in bending compression f,,b has been simplified by expressing the
formulae in terms of geometrical properdes of the section.
Merchant Rankine formula recommended for calculating permis-
sible stresses in axial compression has been used for calculating
permissible stresses in bending compression from the critical
stresses, with value of n, empirically fixed as l-4.
0.4.1 More rigorous analytical procedures than envisaged in this Code
are available and can be made use of for finding effective lengths of com-
pression members in determining elastic critical loads.
0.5 The original tide of the code namely ‘Code of practice for use of
structural steel in general building construction ’ has now been modified as

12
( Code of practice for general construction in steel ‘, since it was felt that
the code is applicable to all types of steel structures and not limited to
buildings only.

0.6 While preparing this Code, the practices prevailing in the field in the
country have been kept in view. Assistance has also been derived from the

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
following publications:
AS 1258-1981 SAA Steel structures code. Standards Association of
Australia.

RS 449 ( Part II )-1969 Specification for I the use of structural

steel in building; Part II Metric units. British Standards
Institution.
AISC Specification for the design, fabrication and erection of
structural steel for buildings. American Institute of Steel
Construction.

SNIP-II-W-72 Code of Practice for design of steel structures of the

USSR State Committee for Construction.

SECTiON 1 GENERAL

1.1 Scope
1.1.1 This code applies to general construction in steel. Specific provisions
for bridges, chimneys, cranes, tanks, transmission line towers, storage
structures, tubular structures and structures using cold formed light gauge
sections, etc, are covered in separate codes.
1.1.2 The provisions of this code generally .apply to riveted, bolted and
welded constructions, using hot rolled steel sections.
1.1.3 This code gives only general guidance as regards the various loads
to be considered in design , For actual loads to be used reference may be
made to IS : 875-1964.
1.2 Termino@gy - For the purpose of this code the following detini-
tions shall apply.
1.2.1 Buckling Load - The load at which a member or a structure as a
whole collapses in service or buckles in a load test.,
1.2.2 Dead Loads - The self weights of all permanent constructions and
installations including the self weights of all walls, partitions, floors ana
roofs.

13
IS r&lo-1904

1.2.3 Effective Lateral Restraint - Restraint which reduces sufficient

resistance in a plane perpendicular to the plane of ben Bing to restrain the
compression flange of a loaded strut, beam or girder from buckling to either
side at the point of application of the restraint.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
1.2.4 Elastic Critical Moment - The elastic moment which will initiate
yielding or cause buckling.
1.2.5 Factor of Safety - The factor by which the yield stress of the
material of a member is divided to arrive at the permissible stress in the
material.
1.2.6 Gauge - The transverse spacing between parallel adjacent lines
of fasteners.
1.2.7 Imposed ( Live ) Load - The load assumed to be produced by the
intended use of occupancy including distributed, concentrated, impact and
vibration and snow loads but excluding, wind and earthquake loads.
1.2.8 Load Factor - The numerical factor by which the working load
is to be multiplied to obtain an appropriate design ultimate load.
1.2.9 Main Member - A structural member which is primarily responsi-
ble for carrying and distributing the applied load.
1.2.10 Pitch - The centre to centre distance- between individual
fasteners in a line of fastener.
1.2.11 Secondary Member - Secondary member is that which is provided
for stability and or restraining the main members from buckling or similar
modes of failure.
1.2.12 Welding Terms - Unless otherwise defined in this standard the
welding terms used shall have the meaning given in IS : 8121957.
1.2.13 Yield Stress - The minimum yield stress of the material in tension
as specified in relevant Indian Standards.
1.3 Symbols - Symbols used in this Code shall have the following mean-
ings with respect to the structure or member or condition, unless other-
wise defined elsewhere in this Code:
A Cross-sectional area ( A used with subscripts has been defined at
appropriate place )
4, b Respectively the greater and lesser projection of the plate beyond
column
B Length of side ofcap or base
be Width of steel flange in encased member
c, Coefficient

14
-

c The distance centre to centre of battens

c Distance between vertical stiffeners
Cl, ca Respectively the lesser and greater distances from the sections
neutral axis to the extreme fibres

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
D Overall depth of beam
d De th of girder - to be taken as the clear distance between
i ange angles or where there are no flange angles the clear
distance between flanges ignoring fillets
to: Diameter of the reduced end of the column
4 i) For the web of a beam without horizontal stiffeners-the clear
distance between the flanges, neglecting fillets or the clear
distance between the inner toes of the flange angles as aipro-
priate.
ii) For the web of a beam with horizontal stiffeners - the clear
distance between the horizontal stiffener and the tension
flange, neglecting fillets or the inner toes of the tension flange
angles as appropriate.
da Twice the clear distance from the neutral axis of a beam to the,
compression flange, neglecting fillets or the inner toes of the
flange angles as appropriate
E The modulus of elasticity for steel, taken as 2 x 10” MPa in this
Code
fY Yield stress
f ob Elastic critical stress in bending
foo Elastic critical stress in compression, also known as Euler
critical stress.
Gauge
f Outstand of the stiffener
I Moment of inertia
Kb or x0 Flexural stiffnesscs
kl, ks Coefficients
k Distance from outer face of flange to web toe of fillet of member
to be stiffened
L Span/length of member
1 Effective length of the member
M Bending moment
M, Maximum moment ( plastic ) capacity of a section
MD0 Maximum moment ( plastic ) capacity of a section subjected to
bending and axial loads

15
Lateral buckling strength in the absence of axial load
Number of parallel planes of battens
Coefficient in the Merchant Rankine formula, assumed as I.4
Axial force, compressive or tensile
Calculated maximum load capacity of a strut

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
Calculated maximum load capacity as a tension member
Euler load
Yield strength of axially loaded section
The reaction of the beam at the support
Radius of gyration of the section
Transverse distance between centroids of rivets groups or
welding
Staggered pitch
Mean thickness of compression flange ( T used with subscripts
has been defined at appropriate place )
Thickness of web
Transverse shear
Longitudinal shear
Calculated maximum shear capacity of a section
Total load
Pressure or loading on the underside of the base
Plaqtic modulus of the section
Ratio of smaller to larger moment
Stiffness ratio
Slenderness ratio of the member; ratio of the effective length ( I)
to the appropriate radius of gyration (Y)

Characteristic slenderness ratio =!?

Al- p,
Maximum permissible compressive stress in an axially loaded
strut not subjected to bending
Maximum permissible tensile stress in an axially loaded tension
member not subjected to bending
Maximum permissible bending stress in slab base
Maximum permissible compressive stress due to bending in a
member not subjected to axial-force.
Maximum permissible tensile stress due to bending in a member
not subjected to axial force

16 --

.
h

lS:doo- 198

CO Maximum permissible stress in concrete in compression

Qe Maximum permissible equivalent stress
UP Maximum permissible bearing stress in a member
=Pf Maximum permissible bearing stress in a fastener
QIlo Maximum permissible stress in steel in compression

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
=ti Maximum permissible stress in axial tension in fastener
uaoc,
081. Calculated average axial compressive stress
Qat,t,oal. Calculated average stress in a member due to an axial tensile
force
flbbo, 081. Calculated compressive stress in a member due to bending about
a principal axis
cbt> oal. Calculated tensile stress in a member due to bending about both
principal axes
+a Maximum permissible average shear stress in a member
Grn Maximum permissible shear stress in a member
Gf Maximum permissible shear stress in fastener
e Ratio of the rotation at the hinge point to the relative elastic
rotation of the far end of the beam segment containing plastic
hinge
V Coefficient
I Ratio of total area of both the flanges at the point of least bend-
ing moment to the corresponding’area ar’the point of greatest
bending moment
0 Ratio of moment of inertia of the compression flange alone to
that of the sum of the moments of inertia of the flanges each
calculated about its own axis parallel to the _Y=Yaxis of the
girder, at the point of maximum bending moment.
NOTE- The aubscri t x, y denote the x-x and r-y axes of the section respec-
tively. For symmetrica P aectioos, x-x denotes the majot principal axti whilrty-y
denotes the minor principal axis.

1.4 Reference to Other Strmddads - All the standards referred to in

this Code are listed as under; and their latest versickshall be applicable:
IS :
226-1975 Structural steel ( standard quality ) (#“A rcvijion )
456-1978 Code of practice for plain and reinforced concrete ( fhirdrevision )
696-1972 Code of practice for general engineering drawings ( second
rmision )
*u.

IS : 800 - 1984

IS :

786-1967 ( Supplement ) SI supplement to Indian Standard conversion

factors and conversion tables (Jrst rcrji&ti\)
812-1957 Glossary of terms relating to welding and cutting of metals
813-1961 Scheme of symbols for welding

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
814 Covered electrodes for metal arc welding of structural steels:
) 814 ( Part 1 )-1974 Part 1 For welding products other than sheets
(fourth revision )
814 ( Part 2 )-1974 Part 2 For welding sheets (jwth revision )
816-196~ Code of practice for use of metal arc welding for general
construction in mild steel (first revision )
817-1966 Code of practice for training and testing of metal arc welders
( Y&Cd)
819:1957 Code of practice for resistance spot welding for light assemb-
lies in mild steel
875-1964 Code of practice for structural safety of buildings: Loading
standards ( rem>ed)
919-1963 Recommendations for limits and fits for engineering (revised )
961-1975 Structural steel ( high tensile ) ( second revision )
962- 1,967 Code of practice for architectural and building drawings (first
revision )
1024-1979 Code of practice for use of welding in bridges and structures
snbjec t to dynamic loading (Jrst revision )
1030-1982 ‘Carbon steel castings for general engineering purposes ( second
revision )
1148-1973 Hot-rolled steel rivet bars ( up to 40 mm diameter ) for struc-
tural purposes ( second revision )
1149-1982 High tensile steel rivet bars for structural purposes
1261-1959 Code of practice for seam welding in mild steel
12781372 Filler rods and wires fo.r gas welding ( second revision )
1323-1962 Code of practice for oxy-acetylene welding for structural work
in mild steel ( revised )
1363-1967 Black hexagon bolts, nuts and lock nuts ( diameter 6 to
39 mm ) and black hexagon screws ( diameter 6 to 24 mm )
.( @t~w.dsion )
1364-1967 Preia)iv; and semi-precision hexagon bolts, screws, nuts and
lo+c,nq~ diameter range 6 to 39 mm ) (Jirst revision )

18

.
 IS: 8901.1984

IS :

1367-1967 Technical supply conditions for threaded fasteners ( jirst rwi-

sion )
1393-1961 Code of practice for training and testing of oxy-acetylene
welders
1395-1971 Molybdenum a$ ehro%ium molybdenum vanad’ lov

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
alloy steel electrodes for metal arc welding ( third r&jT nh))
1477 Code of practice fodpainting of ferrous metals in buildings:
1477 ( Part 1 )-1971 Part 1 Pretreatment ( jirst r&.&n )
1477 ( Part 2 )-I971 Part 2 Painting
1893-1975 Criteria for earthquake resistant design of structures ( third
revision )
1929-1961 Rivets for/general purposes ( 12 to 48 mm diameter )
1977-1975 Structural steel ( ordinary qua&y ) ( secondrevision )
2062- 1984 Weld&\ “structural steel ( third revision )
2155-1962 Rivets t r general purposes (below 12 mm diameter )
36131974 Accep+nce tests for wire-flux combinations for submerged-arc
welding of structural steels ( jirst m&ion )
3640-1967 Hexagon fit bolts
3757-1972 High-tensile friction grip bolts (jirst mixion )
4000-l 967 Code of practice for assembly of structural joints using high
tensile friction grip fasteners
5369-1975 General requirements for plain washers and lock washers
( jirst revision )
5370-1969 Plain washers with outside diameter 3 x inside diameter
5372-1975 Taper washers for channels ( ISMC ) (first revision )
5374-1975 Taper washers for I-beams ( ISMB ) (first r&on )
6419-1971 Welding rods and bare electrodes for gas shielded arc welding
of structural steel
6560-1972 Molybdenum and chromium-molybdenum low alloy steel
welding rods and base electrodes for gas shielded arc,
weIding ’ /

6610-1972 Heavy washers for steel structures

6623-1972 High tensile friction grip nuts
6639-1972 Hexagon bolts for steel structures
6649-1972 High tensile friction grip washers.

19
 IS t 888 - 1984

7205-1973 Safety code for erection of structural steel work

7215-1974 Tolerances for fabrication of steel structures
7280-1974 Bare wire electrodes for submerged arc welding of structural
steels
7807 ( Part 1 )-1974 Approval tests for welding procedures: Part 1 Fusion
welding of steel

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
7818 ( Part 1 )-1974 Approval tests for welders working to approved
welding procedures: Part 1 Fusion welding of steel
7318 (Part 1 )-1974 Approval tests for weldersswhen welding procedure
is not required: Part 1 Fusion welding of steel
8500-1977 Weldable structural steel ( medium and high strength quali-
ties )
9595-1980 Recommendations for metal arc welding of carbon and carbon
manganese steels

13 Units and Conversion Factors - The SI system of units is appfi-

cable to this code. For conversion of system of units to another system,
IS : 786-1967 ( supplement ) may be referred.

1.6 Standard Dimensions, Form and Weight

1.6.1 The dimensions, form, weight, tolerances of all rolled shapes and
other members used in any steel structure shall, wherever available
conform to .the appropriate Indian Standards.

1.6.2 The dimensions, form, weight, tolerances of all rivets, bolts,

nuts, studs, etc, shall conform to the requirements of appropriate Indian
Standards, wherever available.

1.7 Plans and Drawings

1.7.1 Plans, drawings and stress sheet shall be prepared according to

IS : 696-1972 and IS ,: 962-1967.

1.7.1.1 Plans - The plans ( design drawings ) !hall show the com-
plete design with sixes, sections, and the relative locaticns of the various
members. Floor levels, column centres, and offsets shall be dimensioned.
Plans shall be drawn to a scale large enough to convey the information
adequately, Plans shall indicate the type of construction to be employed;
and shall be supplemented by such data on the assumed loads, shears,
moments and axial forces to be resisted by all members and their connec-
tions, as may be required for the proper preparation of shop drawings.
Any special precaution to be taken En the erection of structure from the
design consideration, the same shall also be indicated in the drawing.

20
 IS : 808 - 1984

1.7.1.2 Shop drawings - Shop drawings, giving complete information

necessary for the fabrication of the component parts of the structure in-
cluding the location, type, size, length and detail of all welds, shall be
prepared in advance of the actual fabrication. They shall clearly distinguish
between shop and field rivets, bolts and welds. For additional information

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
to be included on drawings for designs based on the use of welding, refer-
ence shall be made to appropriate Indian Standards. Shop drawings shall
be made in conformity with IS : 696-1972 and IS : 962-1967. A marking
diagram allotting distinct identification marks to each separate part of
steel work shall be prepared. The diagram shall be sufficient to ensure
convenient assembly and erection at site,
1.7.2 Symbols for welding used on plans and shop drawings shall be
according to IS : 813-1961.

SECTION 2 MATERIALS

2.1 Structural Steel - All structural steels used in general construction

coming under the purview of this code shall, before fabrication conform to
IS : 226-1975,. IS : 961-1975, IS : 1977-1975, IS : 2062-1984, and IS:
8500-1977 as appropriate.
3.1.1 Any structural steel other than those specified in 2.1 may also be
used provided that the permissible stresses and other design provisions are
suitably modified and the steel is also suitable for the type of fabrication
adopted.
2.2 Rivets - Rivets shall conform to IS : 1929-1961 and IS : 2155-1962
as appropriate.
2.2.1 High Tensile Steel Rivets - High tensile steel rivets, if used, shall
be manufactured from steel conforming to IS : 1149-1982.
2.3 Welding Consumables
2.3.1 Covered electrodes shall conform to IS: 814 ( Part 1 )-1974,
IS : 814 ( Part 2 )-1974 or IS : 1395-1971 as appropriate.
2.3.2 Filler rods and wires for gas welding shall conform to IS : 12?8-
1972.
2.3.3 The bare wire electrodes for submerged-arc welding shall con-
form to IS : 7280-1974. The combination of wire and flux shall satisfy the
requirements of IS : 3613-1974.
2.3.4 Filler rods and bare electrodes for gas shielded metal arc welding
shall conform to IS : 641941971 and IS : 6560-1972 as appropriate.

21
 Is t 888 - 1984

2.4 Steel Cast&s - Steel castings shall conform to grade 23-45 of

IS: 103011982,”
2.5 Bolts and‘hhtts -_ Bolts and nuts shall co orm to IS: 1363-1967,
IS: 1364-1967, IS: 1367-1967, IS: 3640-1967, I $ : 3757-1972, IS : 6623-
1972, and IS :‘6639-19i2 as appropriate.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
2.6 Washers -‘Washers shall conform to IS : 5369-1975, IS : 5370-1969,
IS: 5372-1975, IS: 5374-1975, IS: 6610-1972, and IS: 6649-1972 as
appropriate.
. 2,7 Cement Concrete - Cement concrete used in association with struc-
; tural steel shall comply with the appropriate provisions of IS : 456-1978.
.2.8 Other Materials - Other materials used in association with struc-
tural steel work shall conform to appropriate Indian Standards.

SECTION 3 GENERAL DESIGN REQUIREMENTS

3.1 Types of Loads

3.1.1 For the purpose of computing the maximum stresses in any struc-
ture or member of a structure, the following loads and load effects shall be
taken into account, where applicable:
Dead loads;
Imposed loads;
Wind loads;
Earthquake loads;
Erection loads; and
Secondary effects due to contraction or expansion resulting from
temperature changes, shrinkage, creep in compression members,
differential settlements of the structure as a whole and its com-
ponents.

3.1,l.l Dead loads, imposed loads and wind loads to be assttmed in

design shall be as specified in IS : 875-1964.
3.1.1.2 Imposed loads arising from equipment, such as cranes, and
machiDes to be assumed in design shall be as per manufacturers/suppliers
data ( see 3.4.2.4 ).
3.1.1.3 Earthquake loads shall be assumed as per. IS : 1893-1975.
3.1.1.4 The erection loads and temperature effects shall be considered
as specified in 3.2 and 3.3.
 IS : 800 - 1984

3.2 Erection Loads

3.2.1 All loads required to be carried by the structure or any part of it
due to storage or positioning of construction material and erection equip-
ment including all loads due to operation of such equipment, shall be
considered as ‘ erection loads ‘. Proper provision shall be made, including

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
temporary bracings to take care of all stresses due to erection loads. The
structure as a whole and all parts of the structure in conjuction with the
temporary bracings shall be capable of sustaining these erection lo tds,
without exceeding the permissible stresses as specified in this code sub_fect
to the allowable increase of stresses as indicated in 3.9. Dead load, wind
load and also such parts of the live load as would be imposed on the struc-
ture during the period of erection shall be taken as acting together with the
erection loads.

3.3 Temperature Effects

3.3.1 Expansion and contraction due to changes in temperature of the
materials of a structure shall be considered and adequate provision made
for the effects produced.
3.3.2 The temperature range varies for different localities and under
different diurnal and seasonal conditions. The absolute maximum and
minimum temperatures which may be expected in different localities in
the country are indicated on the maps of India in Appendices A and B,
respectively. These appendices may be used for guidance in assessing the
maximum variations of temperature for which provision for expansion and
contraction has to be allowed in the structure.
3.3.3 The temperatures indicated on the maps in Appendices A and B
are the air temperatures in the shade. The range of variation in tempera-
ture of the building materials may be appreciably greater or less than the
variation of air temperature and is influenced by the condition of exposure
and the rate at which the materials composing the structure, absorb or
radiate heat. This difference in temperature variations of the material and
air should be given due consideration.

3.3.4 The co-efficient of expansion for steel shall be taken ‘as 0.000 012
per degree centigrade per unit length.

3.4 Design Considerations

3.4.1 General - All parts of the steel framework’ of the structure shall
be capable of sustaining the most adverse combination of the dead loads,
‘prescribed imposed loads, wind loads, earthquake loads where ,applicfble
and any other forces or loads to which the ,building may reasonably be
subjected without exceeding the permissible stresses specified in, this
standard.

23
ISr8oo-1984

3.4.2 Load Combinations

3.4.2.1 Load combinations for design purposes shall be the one that
produces maximum forces and effects and consequently maximum stresses
from the following combinations of loads:
a) Dead load + imposed loads,

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
b) Dead load + imposed loads + wind or earthquake loads, and
c) Dead load + wind or earthquake loads.
NoTe - In case of structures bearing crane loads, imposed loads shall include
the crane effect as given in 3.4.2.4.

3.4.2.2 Wind load and earthquake loads shall be assumed not to

act simultaneously. The effect of both the forces shall be given separately.
3.4.2.3 The effect of cranes to be considered under imposed loads
shall include the vertical loads, eccentricity effects induced by the vertical
loads, impact factors, lateral ( surge ) and the longitudinal horizontal
thrusts acting across and along the crane rail, respectively.
3.4.2.4 The crane loads to be considered shall be as indicated by the
customer. In the absence of any specific indications the load combination
shall be as follows:

a) Vertical loads with full impact from one loaded crane or two
cranes in case of tandem operation together with vertical loads,
without impact, from as many loaded cranes as may be positioned
for maximum effect, alongwith maximum horizontal thrust
( surge ) from one crane only or two cranes in case of tandem
operation;
b) For multibay multicrane gantries - loads as specified in (a) above,
subject to consideration of cranes in maximum of any two bays of
the building cross section;
Cl The longitudinal thrust on a crane track rail shall be considered
for a maximum of two loaded cranes on the track; and
4 Lateral thrust ( surge ) and the longitudinal thrust acting respect
tively across and along the crane rail shall not be assumed to act
simultaneously. The effect of both the forces, shall, however, be
investigated separately.
3.4.2.5 While investigating the effect of earthquake forces the result-
ing effect from dead loads of all cranes parked in each bay positioned for
maximum effect shall be considered.

3.4.2.6 The crane runway girders supporting bumpers shall be

checked for bumper impact loads.

24
 IS : 800 - 1984

3.4.2.7 Stresses developed due to secondary effects such as handling,

erection, temperature effects, settlement of foundations shall be
appropriately added to the stresses calculated from the combination of
loads stated in 3.4.2.1. The total stresses thus calculated shall be within
the permissible limits as specified in 3.9.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
3.4.3 Methods of Design - The following methods may be employed for
the design of the steel framework:
a) Simple design,
b) Semi-rigid design, and
c) Fully rigid design.

3.4.4 Simple Design - This method applies to structures in which the

end connections between members are such that they will not develop
restraint moments adversely affecting the members and the structure as a
whole and in consequence the structure may, for the purpose of design, be
assumed to be pin-jointed.
3.4.4.1 The method of simple design involves the following assump-
tions:

a) Beams are simply supported;

b) All connections of beams, girders or trusses are virtually flexible
and are proportioned for the reaction shears applied at the
appropriate eccentricity;
c) Members in compression are subjected to forces applied at the
appropriate eccentricities ( see 5.3.3 ) with the effective length
given in 5.2; and
d) Members in tension are subjected to longitudinal forces applied
over the net area of the section, as specified under 3.6.2 and 4.2.1.
3.4.5 Semi-Rigid Design - This method, as compared with the simple
design method, permits a reduction in the maximum bending moment in
beams suitably connected to their supports, so as to provide a degree of
direction fixity, and in the case of triangulated frames, it permits account
being taken of the rigidity of the connections and the moment of interaction
of members. In cases where this method of design is employed, calculations
based on general or particular experimental evidence shall be made to show
that the stresses in any part of the structureare not in excess of those laid
down in the code. Stress investigations may also be done on the finished
structure for assurance that the actual stresses under specific design loads
are not in excess of those laid down in the standard.
3.4.6 Fully Rigid Design - This method as compared to the methods of
simple and semi-rigid designs gives the greatest rigidity and economy in

25

.
I$: 800-1984

the weight of steel used when applied in appropriate cases. The end con-
nections of members of the frame shall have sufficient rigidity to hold the
original angles between such members and the members they connect
virtually unchanged. Unless otherwrse specified, the ‘design shall be based
on theoretical methods of elastic analysis and the calculated stresses shall
conform to the relevant provisions of this standard. Alternatively, it shall

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
be based on the principles of plastic design as given in Section 9 of the code.
3.4.7 Exfierimentally Based Design - Where structure is of non-conven-
tional or complex nature, the design may be based on full scale or model
tests subject to the following conditions:
a>A full scale test of prototype structure may be done. The prototype
shall, be accurately measured before testing to determine the
dimensional tolerance in all relevant parts of the structure; the
tolerances then specified on ,the drawing shall be such that all
successive structures shall be in practical conformity with the
prototype. Where the design is based on failure loads, a load
factor of not less than 2.0 on the loads or load combinations given
in 3.4.2 shall be used. Loading devices shall be previously cali-
brated and care shall be exercised to ensure that no artificial
restraintsiare applied to the prototype by the loading systems.
The distribution and duration of forces applied in the test shall
be,representative of those to which the structure is deemed to be
subjected.
b) In the case where design is based on the testing of a small scale
model structure, the model shall be constructed with due regard
for the principles of dimensional similarity. The thrusts, moments
and deformations under working loads shall be determined by
physical measurements made when the loadings are applied to
simulate the conditions assumed in the design of the actual
structure.
3.5 Geometrical ,Prop&ties
3.5.1 General - The geometrical .properties of the gross and the effec-
tive cross sections of a member or part thereof shall be calculated on the
following basis:
a) The properties of the gross cross section shall be calculated .from
the specified size of the member or part thereof.
b) The properties of the effective cross section shall be calculated by
deducting from the-area of the gross cross section the following:
i) T,he sectional area in excess of effective plate width, as given
in 3.5.2, and
ii) The sectional areas of all holes in the section, ,exce@’ fhtit ,$qc ,!,
parts in compression ( see 3.6 ).

26
 ..,...
..I,.. - .“~__ _.“.l-,_ _._-
-“---,~-..l .-- ._._ -. . ,..

IS:808-1984

3.5.2 Plate Thickness

3.5.2.1 If the projection of a plate or flange beyond its connection
to a web, or other line of support or the like, exceeds the relevant values
given in (a), (b) and (c) below, the area of the excess flange shall be

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
neglected when calculating the effective geometrical properties of the
section.
256 ?
a) Flanges and plates in compression - subject to a maximum
with unstiffened edges AlfT- of 16~4
b) Flanges and plates in compression 20 ~~ to the innermost face of
with stiffened edges the stiffening
C) Flanges and plates in tension 201,
NOTE 1 - Stiffened flanges shall include flanges composed of channels or
I-sections or of plates with continuously stiffened edges.
NOTE 2 - ‘II/denotes the thickness of the flange of a section or of a plate in
compression, or the aggregate thickness of plates, if connected together in accor-
dance with the provisions of Section 8, as appropriate.
NOTE 3 - The width ofthe outstand of members referred above shall be taken
as follows:
?W Width of Outstand
Plates Distance from the free edge to the first
row of rivets or welds
Angle, channels, Z-sections and Nominal width
stems of tee sections
Flange of beam and tee sections Half the nominal width
3.5.2.2 Where a plate is connected to other parts of a built up member
along lines generally parallel to the longitudinal axis-of the member, the
width between any two adjacent lines of connections or supports shall not
exceed the following:

1440 '11
a) For plates in uniform compression z subject to a maxi-
JfY mum of 901,
However, where the width exceeds - _-
560 71
subject to a maximum of 357,for welded plates which
-77
are not stressed relieved, or
80011
subject to a maximum of 507,‘for other plates,
q?’
the excess width shall be assumed to be located centrally and its
sectional area shall be neglected when calculating the effective
geometrical properties of the section.

27
fS:800-1984

b) For plates in uniform tension - lOOl1. However where the width

exceeds 60 T1, the excess width shall be assumed to be located
centrally and its sectional area shall be neglected when calculat-
ing the geometrical properties of the section.
In this rule,~shall be taken to be the thickness of the plate,

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
irrespective of whether the plate is a flange or a web of the
member.
3.5.2.3 The provisions contained in 3.5.2.1 and 3.5.2.2 shall not be
applicable to box girders ( where width/depth is greater than 0.2 ) . In
such cases strength is not usually governed by lateral buckling. However,
in such cases check should be exercised for local buckling and yield stress
of material.
3.5.2.4 For only the diaphragm of the box girder, all the provisions
pertaining to size, thickness, spacing etc. as given in 3.5.2.1 and 3.5.2.2
for plate girders shall be applicable.

3.6 Holes

3.6.1 Diameter - In calculating the area to be deducted for rivets, bolts

or pins, the diameter of the hole shall be taken.
3.6.1.1 In making deduction for rivets less than or equal to 25 mm
in diameter, the diameter of the hole shall be assumed to be 1.5 mm in
excess of the nominal diameter of the rivet unless specified otherwise. If
the diameter. of the rivet is greater than 25 mm, the diameter of the hole
shall be assumed to be 2:O mm in excess of the nominal diameter of the
rivet unless specified otherwise.
3.6.1.2 In making deduction for bolts, the diameter of the hole shall
be assumed to be 1.5 mm in excess of the nominal diameter of the bolt,
unless otherwise specified.
3.6.1.3 For counter sunk rivets or bolts the appropriate addition shall
be made to the diameter of the hole.

3.6.2 Deduction for Holes

3.6.2.1 Except as required in 3.6.2.2 the areas to be deducted shall

be the sum of the sectional area of the maximum number of holes in any
cross section at right angles to the direction of stress in the member for:
a) all axially loaded tension members,
b) plate girders with d/t ratio exceeding the limits specified in
6.7.3.1:

28
 IStsoo-1984

where
t = thickness of web, and
d = depth of the girder to be taken as the clear distance
between flange angles or where there are no flange angles
the clear distance between flanges ignoring fillets.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
3.6.2.2 Where bolt or rivet holes are staggered, the area to be
deducted shall be the sum of the sectional areas of all holes in a chain of ,
lines extending progressively across the member, less -$ for each line
extending between holes at other than right angles to the direction of
stress, where, s, g and t are respectively the staggered pitch, gauge, and
thickness associated with the line under consideration [ see Fig. 3.1 (a) 1.
The chain of lines shall be chosen to produce the maximum such deduo
tion. For non-planer sections, such as angles with holes in both legs, the
gauge, g, shall be the distance along the centre of the thickness of the
section between hole centres [ SCGFig. 3.1 (b) 1.

DIRECTION OF FORCE

(al Plates (b ) Angles

DEDUCTION = ( Sum of sectional areas of holes B, C and D )

FIG. 3.1 STAGGEREDPITCH, s, AND GAUGE,g

NOTE - In a built-up member where the chains of holes considered in individ-

ual parts do not correspond with the critical chain of holes for the members as a
whole, the value of any rivets or bolts joining the parts between such chains of holes
shall be taken into account in determining the strength of the member.

29

.
IS:809=1984

3.7 Maximum Slenderness Ratio

3.7.1 The maximum slenderness ratio h of a beam, strut or ten-

sion member given in Table 3.1 shall not be exceeded. In this ( i ’ is we

effective length of the member ( see 5.2 ) and ‘ r ’ is appropriate radius
of gyration based on the effective section as defined in 3.5.1.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE 3.1 MAXIMUM SLENDERNESS RATIOS
MEMBER MAXIMUX SL~DEB-;
&. NESS RATIO A

(1) (2) (3)

i) A member carrying compressive loads resulting from dead 180
loads and imposed loads
ii) A tension member in which a reversal of direct stress due 180
to loads other than wind or seismic forces occurs
iii) A member subjected to compression forces resulting from 250
wind/earthquake forces provided the deformation of
such member does not adversely affect the stress in any
part ofthe structure
iv) Compression flange of a beam 300.

v) A member normally acting as a tie in a roof truss or a 350

bracing system but subject to possible reverse of stress
resulting from the action of wind or earthquake forces
vi) Tension members ( other than pretensioned members ) 400

3.8 Corrosin Protection - Minimum Thickness of Metal

3.8.1 General - Except where the provisions of subsequent clauses in
this section require thicker elements of members, the minimum thickness
of metal for any structural element shall be,, as specified under 3.8.2 to 3.8.4.

3.8.2 Steelwork Dire&Q Exbosed to Weather - Where the steel is directly~

exposed to weather and is fully accessible for cleaning and repainting, the
thickness shall be not less than 6 mm and where the steel is directly exposed
to weather and is not accessible for cleaning and repainting, the thickness
shall be not less than 8 mm. These provisions do not apply to the webs of
Indian Standard rolled steel joists and channels or to packings.
3.8.3 Steelwork not Directly Exposed to Weather
3.8.3.1 The thickness of steel in main members not directly exposed
to weather shall be not less than 6 mm.

3.8.3.2 The thickness of steel in secondary members not directly

exposed to weather shall be not less than 4-5 mm.

30

.
 lS:tMlO-1984

3.8.4 Rolled Steel Beams ‘and Channels - The controlling thickness as

specified ‘under 3.8.2 and 3.9.3 for rolled beams and channels shall
be taken as the mean thickness of flange, regardless of the web thickness.
3.8.5 The requirements of thicknesses specified under 3.8.2 to 3.8.4 do
not apply to special light structural work or to sealed box section or to

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
steel work in which special provision against corrosion, such as use of
special paints has been made or to steelwork exposed to highly corrosive
industrial fumes or vapour or saline atmosphere. In such cases the
minimum thickness of structural and secondary members shall be mutually
settled between the customer and the designer.
3.9 Increase of Stresses
3.9.1 General - Except as specified in 3.9.2 to 3.9.4, all- parts of the
structure shall be so proportioned that the working stresses shall not exceed
the specified values.
3.9.2 Increase in PermaZble Stresses in Members Proportioned for Occasional
Loadings

3.9.2.1 Wind or earthquake loads

4 When the effect of wind or
Structural steel and steel castings -
earthquake load is taken into account, the .permissible stresses
specified may be exceeded by 334 percent.
b) Rivets, bolts and tension rods - When the effect of the wind or
earthquake load is taken into account, the permissible stresses
specified may be exceeded by 25 percent.
3.9.2,2 Erection loads
a) Secondary c$ec&without wind or earthquake loaa!s- For constructions
where secondary effects are considered without wind or earthquake
loads, the permissible stresses on the member or its connections
as specified may be exceeded by 25 percent.
b) Secondary e$ccts combined with wind or earthquake loads - When
secondary effects are considered together with wind or
earthquake,loads, the increase in the permissible stresses shall be as
specified in 3.9.2.1.
3.9.2.3 In no case shall a member or its connections have less
carrying capacity than that needed if the wind or earthquake loads or
secondary effects due to erection loads are neglected.
3.9.3 Increase in Permissible Stresses for Design of Gantry Girders and Their
Supporting Structures - While considering the simultaneous effects of vertical
and horizontal surge loads of cranes for the combination given in 3.4.2.3
and 3.4.2.4 the permissible stresses may be increased by 10 percent.

31
 lstmo-1984

3.3.4 Where the wind load is themain load acting on the structure, no
increase in the permissible stresses is ‘allowed.
3.10 Fluctuation of Stresses
3.10.1 Members subjected to fluctuations of stresses are liable to suffer
from fatigue failure caused by loads much lower than those which would

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
be necessary to cause failure under a single application. The fatigue
cracks are caused primarily due to stress concentrations introduced by
constructional details. Discontinuities such as bolt or rivet holes, welds and
other local or general changes in geometrical form cause such stress con-
centrations from which fatigue cracks may be initiated, and these cracks
may subsequently propagate through the connected or fabricated members.
All details shall, therefore, be designed to avoid, as far as possible,
stress concentrations likely to result in excessive reduction of the fatigue
strength of members or connections. Care shall be taken to avoid sudden
changes of shape of a member or part of a member, especially in regions
of tensile stress or local secondary bending.
Except where specificaily stated to the contrary, the permissible
fatigue stresses for any particular detail are the same for all steels.
3.10.2 When subjected to fluctuations of stresses the permissible stresses
shall be the basic stress stipulated in IS : 1024-1979 for differentfmrll/fmsr
and for different number of stress cycles and classes of constructional
details.
The following provisions shall also be considered while determining
the permissible stress in members subjected to fluctuations of stress:

4 While computing the value off ml=/f msx the effect of wind or
earthquake temperature and secondary stresses shall be ignored
b) For plain steel in the as-rolled condition with no gas cut edges
the constructional detail shall be considered as Class A of IS :
1024-1979.
4 For members of steel with yield stress 280 MPa and over, and
fabricated or connected with bolts or rivets the construction
details shall be considered as Class C of IS : 1024-1979.
For members of steels with yield stress below 280 MPa,
fabricated or connected with bolts or rivets the construction
details shall be considered’as Class D of IS : 1024-1979.
The value off max shall not exceed the permissible tensile or com-
pressive fatigue stress as determined from IS : 1024-1979. Where
co-existent bending and shear stresses are present, f mpxshall
be taken as the principal stress at the point under considera-
tion.

32
3.11 Resistance to Horizontal Foaces
3.11,1 In designing the steel framework of building, l.&visions shall be
made by adequate moment connections or by a system of bracing to
effectively transmit to the foundations all the horizontal forces, making
due allowance ‘for the stiffening effect of the walls and floors, where appli-
cable.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
3.11.2 When the walls, or walls and floors and/or roof are capable of
effectively transmitting all of the horizontal forces directly to the founda-
tions, the structural framework may be designed without considering the
effect of wind.
3.11.3 Wind, and earthquake forces are, reversible and therefore calls
for rigidity in both longitudinal and transverse directions. To provide for
torsional effects of wind and earthquake forces bracings in plan should be
provided and integrally connected with the longitudinal and transverse
bracings to impart adequate torsional resistance to the structure.
3.11.3.1 In shed type buildings, adequate provisions shall be made
by wind bracings to transfer the wind or earthquake loads from trbeir
points of action to the appropriate supporting members. Where the Gon-
nections to the interior columns are so designed that the wind or earth-
quake loads are not transferred to the interior columns, the extlerior
columns shall be designed to resist the total wind or earthquake loads.
Where the connections to the interior columns are so designed that the
wind or earthquake effects are traniferred to the interior columns also, both
exterior and interior columns shall be designed on the assumption that the
wind or earthquake load is divided among them in proportion to their
relative stiffnesses. Columns also should be tested for proper anchorage to
the trusses and other members to withstand the uplifting effect caused by
excessive wind or earthquake pressure from below the roof.
3.11.3.2 Earthquake forces are proportional to the mass of structural
component and the imposed load. Therefore earthquake forces should be
applied at the centre of gravity of all such components of loads and their
transfer to the foundation should be ensured ( see IS : 1893-1975 ).
3.11.3.3 In buildings where high-speed travelling cranes are support-
ed by the structure or where a building or structure is otherwise subj,ected
to vibration or sway, triangulated bracing or especially rigid portal
systems shall be provided to reduce the vibration or sway to a suitable
minimum.
3.11.4 Foundations- The foundations of a building or other structure
shall be so designed as to ensure such rigidity and strength as have been
allowed for in the design of the superstructure, including resistance to all
forces.

“33
_ls:800-1984

3.11.5 Overhang of Walls - Where a wall is placed eccentrically upon

the flange of a supporting steel beam, the beam and its connections shall be
designed for torsion, unless the beam is encased in solid concrete and
reinforced in combination with an adjoining solid floor slab in such a way
as to prevent the beam deforming torsionally.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
3.12 Stability

3.12.1 The stability of the structure as a whole or of any part of it shall

be investigated, and weight or anchorage shall be provided so that the
least restoring moment and anchorage, shall be not less than the sum of
12 times the maximum overturning moment due to dead load and 1.4
times the maximum overturning moment due to imposed loads and wind
or earthquake loads.

3.12.1.1 In cases where dead load provides the restoring moment,

only O-9 times the dead load shall be considered. Restoring moment due
to imposed loads shall be ignored.

3.12.1.2 To ensure stability at all times, account shall be taken of

probable variations in dead load during construction, rapair or other tem-
porary measures. The effect on the load from the deflected or deformed
shape of the structure or of individual elements of the lateral load resisting
systems, may be considered as required.
NOTEI -In complying with the requirements of 3.12.1, it is necessary to
ascertain that the resulting pressures and shear forces to be communicated by the
foundations to the supporting soil would not cause failure.

NOTE 2 - All individual members of the structure which have been designed
for their dead and imposed loads, wind or earthquake loads to the permissible stresses
stipulated in this code shall be deemed to be adequately covered for this margin
of stability.

3.13 Limihg Deflection

3.13.1 Limiting Vertical Deflection

3.13.1.1 The deflection of a member shall be calculated without con-

sidering the impact factor or dynamic effect of the loads causing defiec-
tion.

3.13.1.2 The deflection of member shall not be such as to impair

the strength or efficiency of the structure and lead to damage to finishings.
Generally, the maximum deflection should not exceed l/325 of the span,
but this limit may be exceeded in cases where greater deflection would not
impair the strength or efficiency of the structure or lead to damage to
finishings.

34
 3.13X4 In t&e case of crane runway girder the maximum- vertical
deflection under dead and imposed loads shall not exceed the following
values:
L
4 500

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
L
W Where electric overhead travellingcranes operate,
750
upto5Ot
L
Where electricoverhead _travellingcranes operate, -
=I loo0
over 5ot
L
4 Other moving loads such as charging cars, etc
600
where,
L=spanofcranerunwaygirder.
3.13.2 GmitingHi De&c&m
3.13.2.1 At the caps of cohmms in single storey buildings, the ho+
zontal deflectiondue to lateral forces should not ordinarily exceed l/325
of the actual length ‘P of the column. This limit &y be exceeded in cases
where greater deflection would not impair the strength and effitiency of
the structureor lead to damage to iinishing.
3.13.2.2 The horizontal deflection at column cap. level of columns
supportingcrane runway girdersin the building shall not exceed limits as
may be speci6ed by the purchaser.
3.14 Expansion Joints
3.14.1 In view of the large number of factors involved in deciding the
location, spacing and nature of expansion joints, provisionsof expansion
joints should be left to the discretionof the designer.
3.14.2 Structures in which marked changes in plan dimensions take
place abruptly shall be provided wi_thexpansionjoints at the sectionwhere
such changes occur. Expansionjoints shall be so provided that the neces-
sary movement occurs with a minimum resistanceat the joint. The struc-
ture adjaent to the .joint should preferably be supportedon separate
columns but not necessarilyon separatefoundation.
3.14.3 The details as to the length of a structurewhere expansionjoints
have to be provided may be determined after taking into conrideration
various factors such as temperature, exposure to weather and structural
design, etc. For the purposeof g:,leral guidance the. following pnxisions
have been recommended:
4 If one set of column longitudinal bracing is provided at the
centre of the building pr building section, the length of the
building section may be restricted to 180 metres in case of
covered buildings and 120 metres in case of open gantries
( w Fig. 3.2 ).
IS:888-1984

b> if one set of column bngitudinal bracing are provided near

cenfre of the building/section, the maximum centre line distance
between the two sets of bracing may be restricted to 48 metres for
covered buildings ( and 30 metres for open gantries ) and the
maximum distance between centre of the bracing to the nearest

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
expansion joint/end of ‘building or section may be restricted to
90 metres ( 60 metres in case of open gantries ). The maximum
length ofthe building section thus may be restricted to 228 metres
for covered buildings [ and 150 ‘metres for open gantries ( xee
Fig. 3.3)].
C>The maximum width of the covered building section should
preferably be rest&ted to 150 metres beyond which suitable
provisions for the expansion joints may be made.

FIO. 3.2 MAXIWM LENGTH OF BUILDINGws% ONE SET

OF COLUMNBRACING

EXPANSION JOINi-

FIG. 3.3 MAXIMUMLENGTH OF BUILDINQS~SECTION

WITHTwo SETSOF COLUMNBRACINCN
 lS:&lo-1984

SECTION 4 DESIGN OF TENSION MEMBERS

4.1 Axial Stress

4.1.1 The permissible stress in axial tension, oat, in MPa on the net

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
effective area of the sections shall not exceed:

where,
f y = minimum yield stress of steel, in MPa
4.2 Design Details
4.2.1 .Net Effective Areasfor Angles and Tees in Tension
4.2.1.1 In the case of single angle connected through one leg the
net effective sectional area shall be taken as:
Al + A&
where
AI = effective cross-sectional area of the connected leg,
Aa = the gross cross-sectional area of the unconnected leg, and
3A1
k = 32, + A;
Where lug angles are used, the effective sectional area of the whole
of the angle member shall be considered.
4.2.1.2 In the case of a pair of angles back-to-hack ( or a single tee )
connected by one leg of each angle ( or by the flange of the tee ) to the
same side of a gusset, the net effective area shall be taken as
Al + Ask
where
Al and A, are as defined in 4.2.1.1, and
,5A,
k .
= 5A1 + As

The’anglesshall be connected together along their length in accord-

ante with the requirements under 8.10.3.3.
4.2.1.3 For double angles or tees placed back-to-back and connect-
ed to each side of a gusset or to each side of part of a rolled sections the
areas to be taken in computing the mean tensile stress shall be the effective
area provided the members are connected together along their length as
specified in 8.10.3.3

37
IS:800-1984

Where the angles are back-to-back but are not tack riveted
4.2.1.4
or welded according to 8.10.3.3 the provisions under 4.2.1.2 and 4.2.1.3
shall not apply and each angle shah be designed as a single angle
connected through one leg only in accordancewith 4.2.1.1.
4.2.1.5 When two tees are placed back-to-back but are not tack
riveted or welded as per 8.1033 the provisions under 4.2.1.3 shah not
apply and each tee shall be designed as a singIetee connected to one side

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
of a gussetonly in accordance with 4.2.1.2.
NOTE - The area of the leg of an angle shall he taken as the product of the
thickness +nd the length from the outer corner minus half the thickness. and the area
of the leg of a tee as the product of the thickness and the depth minus the thickness
of the table.

SECTION 5 DESIGN OF COMPRESSION MEMBERS

5.1 Axial Stresses in Uncased Struts

5.1.1 The direct stress in compression on the gross sectionalarea of
axially loaded compressionmembers shall not exceed 0.6~r nor the per-
missiblestressu,, calculated using the following formula:

where

CM = permissiblestressin axial compression,in MPa;

.
fP= yield stressof steel, in M.Pa;
&E
foe= ehtic critical stress in compression,= F

E = modulus of elasticity of steek 2 x 106 MPa;

A ( = l/r) = slendernessratio of the member, ratio of the eiGc&re
length.to appropriate radius of gyration; and
n-a&factor assumed as 1.4.
Values of tr.,, for some of the Jr&an Standard structuralsteelsare
given in Table 5.1 for convenience.
5.2 EffoctiveLength ofCompredonMember8
5.2.1 Gencrd- The slendernessratio of a strut shah be calculated as
the.ratio of the effective length, 1, $o the appropriateradius of gyratioq r.
The effectivelength, 1 shall be derived Corn the actual length, L. The
actualstrut length shah be taken as the length from the centrMo-centre of

38

.
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE 5.1 PERMISSIBLE STRESS uac ( MPa N AXIAL COMPRESSION
FOR STEELS WITH VARIOUS YIELD STRESS
( czuusc 5.1.1 )

220 230 243 250 260 280 300 320 340 360 380 400 420 450 480 510 540

10 132 138 144 150 156 168 180 192 204 215 227 239 251 269 287 305 323
131 137 142 148 154 166 177 189 201 212 224 235 246 263 280 297 314
zi 128 134 140 145 151 162 172 183 194 204 215 225 236 251 266 280 295
124 129 145 154 164 174 183 192 201 231 243 255 267
sx 118 123 u”; n; 136 145 153 161 168 176 183 % :A; 233
115 118 122 126 133 139 146 152 158 163 168 173 f;; Z; 225
193
% 102 106 1;; ;A$ ;g 120 125 130 135 139 142 147 150 155 160 164 :z
93 107 111 115 118 121 124 127 129 133 136 139 141
2 8.5 :; 88 90 92 98 101 103 105 108 109 111 114 116 118 119
76 ii: 86 92 96 101
g :t 78
69 71
79 % !Z 74 76 tt LO iif ii; 83 ii 85
gg lizi
120 :i 67 70 71_ 71 72 73 iz 74 ;;
130 55 65
140 49 z: 2 ti:
49
fZ
49
:: 56 it 57
150 47 48 50
160 2 43 43 ii 49 50
44 44
170 ifi ;i
180 34 35 3359 iii 35
iii iz ;z
190
zti 2381 ;i :i 32 ;: :z
fZ
220 23
26 26
24
26
24 ;:
26
24
26 :: 26 26

230
240
;: 22 2
20
22
20
22
20
22
20 if
24
2’:
ii
20
fi
20
;:
20
250 2o
18 :80 18 19 19 19 19 19 19 19 19
 . _ ._. . -. . -.. . _. -- .-- ---

lS:tUlO -1984

inter-sections with supporting members, or the cantilevered length in the

case of free-standing struts.
5.2.2 E_$ective Length - Where accurate frame analysis is not done, the
effective length of a compression member in a given plane may be deter-
mined by the procedure given in Appendix C. However, in most cases the
effective length in the given plane assessed on the basis of Table 5.2,

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
would be adequate. Effective length as given in Table 5.2 may also be
adopted where columns directly form part of framed structures.
5.2.3 Eccentric Beam Connections - In cases where the beam connections
are eccentric with respect to the axes of the columns, the same conditions
of restraint shall be deemed to apply, provided the connections are carried
across the flange or web of the columns as the case may be, and the web
of the beam lies within, or .in direct contact with the column section.
Where practical difficulties prevent this, the effective length shall be
estimated to accord with the case appropriate to no restraint in that
direction.
5.2.4 Members of Trusses - In the case of bolted, riveted or welded
trusses and braced frames, the effective length ‘ 1’ of the compression mem-
bers shall be taken as between 0.7 and 1.0 times the distance between
centres of inter-sections, depending on the degree ,of end restraint provid-
ed. In the case of members of trusses buckling in the plane perpendicu-
lar to the plane of the truss the effective length shall be taken as 1.0 times
the distance between points of restraints. The design of disc_ontinuous angle
struts shall be as specified in 5.5.
5.2.5 Stepped Columns - A method of determining the effective length of
stepped columns is given in Appendix D.
5.3 Des@ Details
5.3.1 Thickness of Elements - The thickness of an outstanding leg of any
member in compression shall be in accordance with 3.5.2.1 and 3.5.2.2.
5.3.2 @fictive Sectional Area - Except as modified under 3.5.2 the gross
sectional area shall be taken for all compression members connected by
welds and turned and fitted bolts and’pins except that holes, which are not
fitted with rivets, weld or tight-fitting bolts and pins, shall be deducted.
5.3.3 ficentricity for Stanchion and Solid Columns
5.3.3.1 For the purpose of determining the stress in a stanchion or
column section, the beam reactions or similar loads shall be assumed to be
applied 100 mm from the face of the section or at the centre of bearing
whichever dimension gives the greater eccentricity, and with the exemption
of the following two cases:
a) In the case of cap connections, the load shall be assumed to be
applied at the face of the column shaft or stanchion section; or
edge of packing if used, towards the span of the beam; and

40
 18 I 888 - 1984

TABLE 5.2 EFFECTIVE LENGTH OF COMPRESSION MEMBERS

OF CONSTANT DIMENSIONS
( Clause 5.2.2 )
DEGREEOFEND RESTRAINT OB RECOMMENDED SYMBOL
VALUE OF

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
COMPRESSION Mmrnmt
EFFECTIVE
LENGTH

(1) (2) (3)

a) Effectively held in position and 0’65 L

restrained against rotation at
both ends

b) Effectively held in position at 0.80 L

\,
both ends and restrained against
rotation at one. end

c) Effectively
both ends, but
held

against rotation
in position at
not restrained

41
l-00 L

1 /’
I
I

( Canfinued)
I
;
1.
L. _ ., _. ._~..

fS:888- 1984

TABLE 5.2 EFFECTIVE LENGTH OF COMPRESSION MEMBBBS

OF CONSTANT DIMENSIONS - Cod

DEGREE oY END RESTRAINT OP RECOMMENDED 5YhtBOL

COMPREBSION MEYBEB VALWOB
EEXXCTIVE
LENGTH

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
(1) (2)

d) Effectively held in position and 1’20 L

restrained against rotation at one
end, and at the other end res-
trained against rotation but not
held in position

e) Effectively held in position and 1’50 L

restrained against rotation at
one end, and at the other end
partially restrained against
rotation but not held in position

f) Effectively held in position at 2’00 L

one end but not restrained
against rotation, and at the other
end restrained against rotation
but not held in position

42
 tS : 804 - 1984

TABLE 5.2 EFFECTIVE LENGTH OF C&IMPRESSION MEMBEBS

OF CONSTANT DIMENSIONS - Contd
DE~UEE OCR END RESTEAINT OB RE~OMXENDED SYMBOL
C~IUTSSSION MEIXBEX VALUE OF
EFFECTIVE
LENGTH

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
(1)

g) Effectively held in position and

rdstrained against rotation at
one end but not held in position
n0r restrained against rotation
at the other end

NOTE 1 - L is the unsupported length of compression member.

NOTE 2 -For battened struts the effective length shall be increascd.by 10
percent.

b) In the case of a roof truss bearing on a cap, no eccentricity need

be taken for simple bearings without connections capable of
developing an appreciable moment.
5.3.3.2 In continuous columns, the bending moments due to
eccentricities of loading on the columns at any floor may be taken as:
a) ineffective at the floor levels above and below that floor; and
b) divided equally between the column’s lengths above and below
that floor level, provided that the moment of inertia of either
column section, divided by its effective length does not exceed
l-5 times the corresponding value of the other column. In case
where this ratio is exceeded, the bending moment shall be divided
in proportion to the moments of inertia of the column sections
divided by their respective effective lengths.
53.4 S#ices
5.3.4.1 Where the ends of compression members are faced for
bearing over the whole area, they shall be spliced to hold the connected
members accurately in position, and to resist any tension when bending is
present.
The ends of compression members faced for bearing shall invariably
be machined to ensure perfect contact of surfaces in bearing.
 IS t 800 - 1984

5.3.4.2 Where such members are not faced for complete bearing the
splices shall be designed to transmit all the forces to which they are
subjected.

5.3.4.3 Wherever possible, splices shall be proportioned and

arranged so that the centroidal axis of the splice coincides as nearly as
possible with the centroidal axes of the members jointed in order to avoid

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
eccentricity; but where eccentricity is present in the joint, the resulting
stress shall be provided for.

5.4 Column Bases

5.4.1 Gusseted Bases-For stanchion with gusseted bases, the gusset plates,
angle cleats, stiffeners, fastenings, etc, in combination with the bearing
area of the shaft shall be sufficient to take the loads, bending moments
and reactions to the base plate without exceeding specified stresses. All the
bearing surfaces shall be machined t) ensure perfect contact.

5.4.1.1 Where the ends of the column shaft and the gusset plates
are not faced for complete bearing, the fastenings connecting them to the
base plate shall be sufficient to transmit all the forces to which the base is
subjected..

5.4.2 Column and Base Plate Connections - Where the end of the column
is connected directly to the base plate by means of full penetration butt
welds the connection shall be deemed to transmit to the base all the forces
and moments to which the column is subjected.

5.4.3 Slab Bases - Columns with slab bases need not be provided with
gussets, but fastenings shall be provided sufficient to retain the parts
securely in plate and to resist all moments and forces, other than direct
compression, including those arising during transit, unloading and erection.
When the slab alone distributes the load uniformly, the minimum
thickness of a rectangular slab shall be given by the following formula:

t=d_$(aa-$)

where
t = the slab thickness, in mm;
w = the pressure or loading on the underside of the base,
in MPa;
a = the greater projection of the plate beyond column, in
mm;

44
 IS : 800 - Aad4

b = the lesser projection of the plate beyond the coiumn,

in mm; and
bba = the permissible bending stress in slab bases ( for a11steels,
shall be assumed as 185 MPa ).

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
5.4.3.1 When the slab does not distribute the loading uniformly or
where the slab is not rectangular, special calculations shall be made to
show that the stresses are within the specified limits.
5.4.3.2 For solid round steel columns, in cases where the loading on
the cap or under the base is uniformly distributed over the whole area
including the column shaft, the minimum thickness of the square cap or
base shall be:

90 w B
t=10 ____ ~
16 abs ’ B-do
where
t the thickness of the plate, in mm;
W 1 the total axial load, in kN;
B = the length of the side of cap or base, in mm;
gbs = the permissible bending stress in slab bases ( for all steels,
shall be assumed as 185 MPa ); and
d,, = the diameter of the reduced end, if any, of the column,
in mm.
5.4.3.3 When the load on the cap or under the base is not uniformly
distributed or where end of the column shaft is not machined with the cap
or base, or where the cap or base is not square in plan, calculations shall
be made based on the allowable stress of 185 MPa.

5.4.3.4 The cap or base plateshall not be less than l-5( do + 75 ) mm

in length or diameter.

5.4.3.5 The area of the shoulder ( the annular bearing area ) shall
be sufficient to limit the stress in bearing, for the whole of the load com-
municated to the slab, to the maximum values given in 6.3, and resistance
to any bending communicated to the shaft by the slab shall be taken as
assisted by bearing pressures developed against the reduced end of the
shaft in conjunction with the shoulder.
5.4.3.6 Bases for bearing upon concrete or masonry need not be
machined on the underside provided the reduced end of the shaft termi-
nates short of the surface of the slab, and in all cases the area of the
reduced end shall be neglected in calculating the bearing pressure from the
base.

45
-.

5.4.3.7 In cases where the cap or base is fillet welded direct to the
end of the column without boring and shouldering, the contact surfaces
shall be machined to give a perfect bearing and the welding shall be
sufficient to transmit the forces as required in 5.43 and its sub-clauses for
fastening to slab bases. Where full strength T-butt welds are provided no

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
machining of contact surfaces shall be required.
5.4.4 Base Plates and Bearing Plates - The base plates and grillages of
stanchions and the bearing and spreaders of beams and girders shall be
of adequate strength, stiffness and area, to spread the load upon the eon-
Crete, masonry, other foundation, or other supports without exceeding the
permissible stress on such foundation under any combination of load and
bending moments.
5.5 Angle Struts
5.5.1 Single Angle Struts
a) Single angle discontinuous struts connected by a single rivet or
bolt may be designed for axial load only provided the compressive
stress does not exceed 80 percent of the values given in Table 5.1
in which the effective length c 1 ’ of the strut shall be taken as
centre-to-centre of intersection at each end and ‘ r ’ is the mini-
mum radius of gyration. In no case, however, shall the ratio of
slenderness for such single angle struts exceed 180.
b) Single angle discontinuous struts connected by a weld or by two
or more rivets or bolts in line along the angle at each end may
be designed for axial load only provided the compression stress
does not exceed the values given in Table 5.1, in which the
effective length ‘ 1’ shall be taken as 0.85 time the length of the
strut, centre-to-centre of intersection at each end and ‘ I ’ is the
minimum radius of gyration.
5.5.2 Double Angle Strutr
a) For double angle discontinuous struts, back to back connected to
both sides of the gusset or section by not less than two bolts or
rivets in line along the angles at each end, or by the equivalent
in welding, the load may be regarded as applied axially. The effec-
tive length ‘ I ’ in the plane of end gusset shall be taken as between
0.7 and 0.85 times the distance between intersections, depending
on the degree of the restraint provided and in the plane perpen-
dicular to that of the end, gusset, the effective length ‘ I ’ shall be
taken as equal to the distance between centres of intersections.
The calculated average compressive stress shall not exceed the
values obtained from,Table 5.1 for the ratio of slenderness based
on the appropriate radius of gyration. The angles shall be con-
nected tegether in their lengths so as to satisfy the requirements
of 5.9 and 8.10.3.

46 1
 IS : 800 - 1984

b) Double angle discontinuous ,struts back-to-back, connected to one

side of a gusset or section by a one or more bolts or rivets in each
angle, or by the equivalent in .welding, shall be designed as for
single angles in accordance with 5.5.1 (a) and the angles shall be
connected together in their length so as to satisfy the require-

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
ments of 5.9 and 8.10.3.

5.5.3 Continuous Members - Single or double angle continuous struts, such

as those forming the flanges, chords or ties of trusses or trussed girders, or the
legs of towers shall be designed as axially loaded compression members,
and the effective length shall be taken in accordance with 5.2.4.

5.5.4 Combined Stresses - If the struts carry, in addition to axial loads,

loads which cause transverse bending, the combined bending and axial
stresses shall be checked in accordance with 7.1.1. For determining the
permissible axial and bending stresses, for use in applying 7.1.1, the
effective length shall be taken in accordance with 5.2 and 6.6.1, respec-
tively.

5.6 Steel Castings - The use of steel castings shall be limited to bear-
ings, junctions and other similar parts and the working stresses shall not
exceed the workings stresses given in this standard for steel of yield stress
250 MPa.

5.7 Lacing

5.7.1 General

5.7.1.1 Compression members’ comprising of two main components

laced and tied should where practicable, have a radius of gyration about
the axis perpendicular to the plane of lacing not less than the radius of
gyration about the axis in the plane of lacing ( see Fig. 5.1A ).

5.7.1.2 As far as practicable the lacing system shall not be varied

throughout the length of the strut.

5.7.1.3 Except for tie plates as specified in 5.8 double laced system
( see Fig. 5.1B ) and single laced systems on opposite sides of the main
components shall not be combined with cross members perpendicular to
the longitudinal axis of the strut unless all forces resulting from deforma-
tion of the strut members are calculated and provided for in the lacing and
its fastenings ( see Fig. 5.1C ).

5.7.1.4 Single laced systems on opposite sides of the components

shall preferably be in the same direction so that one be the shadow of the
other, instead of being mutually opposed in direction ( see Fig. 5.1D ).

47
IS: 808- 1984

5.7.2 Design of Lacing

5.7.2.1 The lacing of compression members shall be proportioned to
resist a total transverse shear ‘ V’ at any point in the length of the member
equal to at least 2-5 percent of the axial force in the member, which shear
shall be considered as divided equally among all transverse lacing systems
in parallel planes.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
5.7.2.2 For members carrying calculated bending stress due to
eccentricity of loading, applied end moments and/or lateral loading, the
lacing shall be proportioned to resist the shear due to the bending in addi-
tion to that specified under 5.7.2.1.
5.7.2.3 The slenderness ratio ‘h’ of the lacing bars for compression
members shall not exceed 145. In riveted constrpction, the effective length
of lacing bars for the determination of the permissible stress shall be take,n
as the length between the inner end rivets of thk bars for sirigle lacing,
and as O-7 of this length for double lacing $Fectively tiveted at intersec-
tion’. Ili welded construction, the effective lengths fhzill be taken as
0.7 times the distance between the inner ends of welkls connecting the
lacing bars to the member.

xE..-3x Y
LACING ON LACING ON
ry < rx FACE AA FACE BB

Fro. 5.1A LACING DETAILS Fro. 5.1B DOUBLE LACING SYSTEM

48

,
 .

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
..hEi!
.. .
.m
.
I
a . .
. . .

.E
...
/. l-2
fiz
1 .
.
4
.

Fro> 5. IC DOUBLE LACED AND SINQLE LACED SYSTEMS

COMBINED
WITHCROSSMEMBERS

49

‘.
km,__..,.. . .,_ - .._...

I8 : 888 - 1984

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
LACING ON LACING ON LACING ON LACING
ON
FACE A FACE B FACE A FACE E
PREFERRED NOT PREFERREO

Fro. 5.1D SINQLE LACED SYSTEMON OPPOSITE SIDES OF

MAIN COMPONENTS

5.7.3 Width of Lacing Bars.- In riveted construction, the minimum

width of laang bars shall be as follows:
Nominal Rivtt Dia Width of Lacing Bars
mm mm
22 65
20 60
18 55
16 50

5.7.4 Thickntss of Lacing Bars - The thickness of flat lacing bars shall
be not less than one-fortieth of the length between the inner end rivets or
welds for single lacing, and one-sixtieth of this length for double lacing
riveted or welded at intersections.
5.7.4.1 Rolled sections or tubes of equivalent strength may be used
instead of flats.

50

.
 18:800-1984

5.7.5 Angle of Inclination - Lacing bars, whether in double or single

systems, shall be inclined at an angle not less than 40 degree nor more
than 70 degrees to the axis of the member.
NOTE - The required section for lacing bars for compression membea or for
tensionmembers subject to bending shall be determined by using the appropriate

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
permissible stressessubject to the requirements in 5.7.5 and 5.7.4. For tension
members under stress, only the lacing ban shall be subject to the requirements
of 5.735.7.4 and 5.7.5.
5.7.6 Spating

5.7.6.1 The maximum spacing of lacing bars, whether connected by

riveting or welding, shall also be such that the minimum slenderness ratio
r\ ( I Z/r) of the components of the member between consecutive connections
is not greater than 50 or O-7 times the most unfavourable slenderness ratio
of the member as a whole, whichever is less, where ‘1 is the distance between
the centres of connection of the lattice bars to each component.
5.7.6.2 Where lacing bars are not lapped to form the connection to
the components of the members, they shall be so connected that there
is no appreciable interruption in the triangulation of the system.

5.7.7 Attachment to Main Members - The riveting or welding of lacing

bars to the main members shall be sufficient to transmit the load in the
bars. Where welded lacing bars overlap the main members, the amount
of lap measured along either edge of the lacing bar shall be not less than
four times the thickness of the bar or the members, whichever is less. The
welding shouid be sufficient to transmit the load in the bar and shall,
in any case, be provided along each side of the bar for the full length
of lap.
5.7.7.1 Where lacing bars are fitted between the main members,
they shall be connected to each member by fillet welds on each side of the
b8r or by full penetration butt welds. The lacing bars shall I)r so placed
as to be generally opposite the flange or stiffening elements of the main
member.
5.7.8 End Tie Plates - Laced compression members shall be provided
with tie plates at the ends of lacing systems and at points where the
systems are interrupted ( see also 5.8 ).

5.8 Battening and Tie Plates

5.8.1 General

5.8.1.1 Compression members composed of two main components

battened should preferably have their two main components of the same
cross section and symmetrically disposed about their x-x axis. Where
practicable, the compression members should have a radius of gyration

51
Is:mJ-1984

about the axis perpendicular to the plane of the batten not less -than the
radius of gyration about the axis in the plane of batten.
5.8.1.2 Battened compression members not complying with the
requirements specified in thii clause or those subjected, in the plane of the
battens, to eccentricity of loading, applied moments or lateral forces ( see
Fig. 5.2 ) shall be designed according to the exact theory of elastic stability

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
or empirically from the verification of tests, so that they have a load
factor of not less than l-7 in the actual structure.

Fro. 5.2 BATTENCOLUMN SECTION

NOTE - If the column section ls subjected to eccentricity or other moments
aboutl-y axis the battens and the column section should be specially designed for
such moments.

5.8.1.3 The battens shall be placed opposite each other at each end
of the member and points where the member is stayed in its length and
shall, as far as practicable, be spaced and proportioned uniformly through-
out. The number of battens shall be such that the member is divided
into not less than three bays within its actual length from centre to centre
of connection.

52
 rs:800-1984

5.8.2 Design

5.8.2.1 Battens - Battens shall be designed to carry the bending

moments and shears arising from transverse shear force ‘V’ of 2.5 percent
of the total axial force on the whole compression member, at any point in

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
the length of the member, divided equally between parallel planes of
battens. The main members shall also be checked for the same shear force
-and bending moments as for the battens.

Battens shall be of plates, angles, channels, or I-sections and shall be

riveted or welded to the main components so as to resist simultaneously a
V.C
longitudinal shear VI = g and a moment M = -
2N

where

V = the transverse shear force as defined above;

C = the distance centre-to-centre of battens, longitudinally;
.N = the number of parallel‘pianes of battens; and
5’ = the minimum transverse distance between the centroids
of the rivet group/welding.

5.8.2.2 Tie plates - Tie plates shall be designed by the same method
as battens. In no case shall a tie plate and its fastenings be incapable of
carrying the forces for which the lacing has been designed.

5.8.2.3 Siie - When plates are used for battens, the end battens and
those at points where the member is stayed in its length shall thave an
effective depth, longitudinally, of not less than the perpendicular distance
between the centroids of the main members, and intermediate battens
shall have an effective depth of not less than three quarters of this dis-
tance, but in no case shall the effective depth .of any batten be less than
twice the width of one member in the plane of the battens. The effective
depth of a batten shall be taken as the longitudinal distance between end
rivets or end welds.

The thickness of batten or the tie plates shall be not less than one-
fiftieth of the distance between the innermost connecting lines of rivets or
welds.

5.8.2.4 The requirement of size and thickness specified above does

not apply when angles, channels or I-sections are used for battens with
their legs or flanges perpendicular to the main member. However, it should
be ensured that the ends of the compression members are tied to achieve
adequate rigidity.

53
IS : 800 - 1984

5.0.3 S’acing of Battens

5.8.3.1 In battened compression members not specifically checked for

shear stress and bending moments as specified in 5.8.2.1, the spacing of
battens centre-to-centre of end fastenings shall be such that the slenderness

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
ratio c A’ of the lesser main component over that distance shall be not greater
than 50 or greater than 0.7 time the slenderness ratio of the member as
a whole, about its X-X ( axis parallel to the battens ).
NOTEZ- With regard to effective lesgth of the battened coniprevion member
as a whole, reference may be made to Table 5.2.

5.8.3.2 The number of battens shall be such that the member is

divided into not less than three parts longitudinally.

5.8.4 Attachment to Main Mmbcrs

5.8.4.1 W&d connections - Where tie or batten plates ovt~lap the
main members, the amount of lap shall be not less than four times the
thickness of the plate. The length of weld connecting each edge of the
batten plate to the member shall, in aggregate, be not less than half the
depth of the batten plate. At least one-third of the weld shall be placed
at each end of this edge. The length of weld and depth of batten plate
shall be measured along the longitudinal axis of the main member.

In addition, the welding shall be returned along the other two edges
of the plates transversely to the axis of the main member for a length not
less than the minimum lap specified above.

5.9 Compkession Members Composed of Two Components Back-

to-Back

5.9.1 Compression members composed of two angles, channels, or tees,

back-to-back in contact or separated by a small distance shall be connect-
ed together by riveting, bolting or welding so that the ratio of slenderness
of each member between the connections is not greater than 40 or greater
than O-6 times the most unfavourable ratio of slenderness of the strut as a
whole, whichever is less ( see also Section 8 -).

5.9.2 In no case shall the ends of the, strut be connected together with
less than two rivets or bolts or their equivalent in welding, and there shall
be not less than two additional connections spaced equidistant in the length
of strut. Where the members are separated back-to-back, the rivets or
bolts through these connections shall pass through solid washers or pack-
ings, and where the legs of the connected angles or tables of the connected
-tees are 125 mm wide or over, or where webs of channels are 150 mm
wide or over, not less than two rivets or bolts shall be used in each con-
nection, one on line of each gauge mark.

54
L-r_ .I.._ _. . - i.*-.. ,,

I ~.-.~--~-1_“1. “__-_- . . -“I...- ._.,...-...

._ .__--__ ^ ... ~..I
_-

IS : 800.. 1984

5.9.3 Where these connections are made by welding, solid packings

shall be used to effect the j jinting unless the members are sufficiently close
together to permit welding, and the members shall be connected by weld-
ing along both pairs of edges of the main components.
5.9.4 The rivets, bolts or welds in these connections shall be sufficient

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
to carry the shear force and moments, if any, specified for battened struts,
and in no case shall the rivets or bolts be less than 16 mm diameter for
members up to and including 10 mm thick, 20 mm diameter for members
up to and including 16 mm thick; and 22 mm diameter for members over
16 mm thick.
5.9.4.1 Compression members connected by such riveting, bolting or
welding shall not be subjected to transverse loading in a plane perpendi-
cular to the washer-riveted, bolted or welded surfaces.
5.9.5 Where the components are in contact back-to-back, the spacing
of the rivets, bolts or intermittent welds shall not exceed the maximum
spacing for compression members as given in 6.1.4 and 6.2.6 of IS : 816-
1969.

SECTION 6 DESIGN OF MEMBERS

SUBJECTED TO BENDING

6.1 General - The calculated stress in a member subjected to bending

shall not exceed any of the appropriate maximum permissible stresses given
in 6.2 for bending, 6.3 for bearing, 6.4 for shear and in 7.1 for the com-
bination of stresses.
6.2 Bending Stresses
6.2.1 Maximum Bending Stresses - The maximum bending stress in
tension ( cbt, csr ) or in Compression ( cbO, es1 ) in extreme fibre calculated
on the effective section of ‘a beam shall not exceed the maximum permis-
sible bending stress in tension ( @bt ) or in compression ( cbO ) obtained
as follows nor the values specified in 6.2.2, 6.2.3, 6.2.5 and 6.2.6, as
appropriate:
,,,,t Or t,,,o - O*SSf,,.
6.2.2 Maximum Permissible Bending Comjressiae Stress in Beams and Channels
with Equal Flanges - For an I-beam or channel with equal flanges bent
about the axis of maximum strength ( X-X axis ), the maximum bending
compressive stress on the extreme fibre calculated on the effective section
shah not exceed the values of maximum permissible bending compressive
stress, @,e, given directly in Table 6.1A or 6. lB, Table 6 1C or 6.1D and
Table 6.1 E or 6. lF, as appropriate, for steels with yield stress fy of 250 MPa,
340 MPa and 400 MPa, respectively. For steels with yield stresses other

.
 than those covered in Tables 6.1A to 6.1F, maximum permissible bending
compressive stress shall be obtained in accordance with 6.2.3 and 6.24.
NOTE - Tables 6.1A to 6.1F have been derived in accordance with 6a.3
and 6.2.4.

6.2.2.1 In Tables 6.1A to 6.1F:

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
D - overall depth of beam;
41 - depth of web ( see 1.3 );
1 = effective length of compression flange ( see 6.6 );
ry = radius of gyration of the section about its axis of minimum
strength (y-y axis );
T- mean thickness of the compression flange, is equal to the area
of horizontal portion of flange divided by width; and
t = web thickness. .*
For rolled sections, the mean thickness is that given in appropriate
Indian Standards. *
In case of compound girders with curtailed flanges, D shall be taken
as the overall depth of the girder at the point of maximum bending
moment, and T shall be taken as the effective thickness of the compression
flange and shall be calculated as:
T = X1 x mean thickness of the horizontal portion of the compres-
sion flange at the point of maximum bending moment. Coeffi-
cient K1 is defined in 6.2.4.
6.2.3 Maximum Permissible Bending Compressive Stress in Beams and Plate
Girders - For beams and plate girders, bent about the axis of maximum
strength ( x-x axis ), the maximum bending compressive stress on the
extreme fibre, calculated on the effective section shall not exceed the
maximum permissible bending compressive stress gbOin MPa obtained by
the following formula:

where
f ob = elastic critical stress in bending, calculated in accordance
with 6.2.4 or by an elastic flexural-torsional buckling
analysis, in MPa;
fr - yield stress of the steel in MPa; and
a ===a factor assumed as 1.4.

Values of ebO as derived from the above formula for some of the
Indian Standard structure1 steels are given in Table 6.2.

56
 IS : 800 - 1984
TABLE 6.1A MAXIMUM PERMISSIBLE BENDING STRESSES, mc ( MPn ),
IN EQUAL-FLANGE I-BEAMS OR CHANNELS
( Clause 6.2.2 )

with fy = 250 MPa, : > 2’0 or -$- > 85

Dl l-+
8 10 12 14 16 18 20 25 30 35 40 50 60 80 100

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
bY
L
40 160 160 159 159 158 158 158 158 158 157 157 157 157 157 157
45 159 158 157 157 156 156 156 155 155 155 155 155 154 154 154
50 158 157 156 155 154 154 153 153 152 152 152 151 151 151 151
55 157 155 154 153 152 151 150 149 149 148 148 148 148 147 147
60 156 153 152 150 149 148 148 146 145 145 144 144 1$4 143 143
65 154 152 150 148 147 145 144 143 142 141 140 140 139 139 139
70 153 150 148 14 144 142 141 139 138 137 136 135 135 135 134
75 152 148 145 143 141 139 138 136 134 133 132 131 130 130 129
80 150 147 143 141 138 136 135 132 130 128 128 126 126 125 125
85 149 145 141 138 136 133 132 128 126 124 123 122 121 120 120
90 147 143 139 136 133 130 128 124 122 120 119 117 116 115 115
95 146 141 137 133 130 128 125 121 118 116 114 112 111 110 110
100 145 140 135 131 128 125 122 117 114 112 110 108 107 105 105
110 142 136 131 127 123 119 116 111 107 104 102 99 98 96 95
120 139 133 127 122 118 114 111 104 100 97 94 91 90 88 87
130 137 130 124 118 113 109 106 99 94 90 88 84 82 80 79
140 134 127 120 114 109 105 101 93 88 84 81 78 75 73 72
150 132 124 117 110 105 100 96 88 83 79 76 72 69 67 65
160 129 121 113 107 101 96 92 84 78 74 71 66 64 61 60
170 127 118 110 104 98 93 88 80 74 69 66 62 59 56 55
180 124 115 107 100 94 89 85 76 70 65 62 58 55 52 50
190 122 113 104 97 91 86 82 73 66 62 58 54 51 48 46
200 120 110 102 94 88 83 78 70 63 59 55 50 48 44 43
210 118 108 99 92 86 80 76 67 60 56 52 47 44 41 40
220 116 105 97 89 83 78 73 64 58 53 49 45 42 38 37
230 113 103 94 87 80 75 70 62 55 51 47 42 39 36 34
240 111 101 92 84 78 73 68 59 53 48 45 40 37 34 32
250 109 99 90 82 76 70 66 57 51 46 43 38 35 32 30
260 107 97 88 80 74 68 64 55 49 44 41 36 33 30 28
270 106 95 86 78 72 66 62 53 47 43 39 35 32 28 26
280 104 93 84 76 70 65 60 51 45 41 38 33 30 27 25
290 102 91 82 74 68 63 58 50 44 39 36 32 29 25 24
300 100 89 80 72 66 61 57 48 42 38 35 30 27 24 22

57
 TABLE 6.1B MAXIMUM PERMISSIBLE BENDING STRESSES, ubo ( MPa ),
IN EQUAL FLANGE I-BEAMS OR CHANNELS
( &WS6 6.2.2 )

with f y= 250 MPa, +2*Oand+ 6 85

D/T-
8 10 12 14 16 18 20 25 30 35 40 50 60 80 100

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
l/‘J
--
40 161 161 160 160 160 160 160 159 159 159 159 159 159 159 159
45 161 160 159 159 158 158 158 157 157 157 157 157 157 157 157
50 160 158 158 157 156 156 156 155 155 155 154 154 154 154 154
55 159 157 156 155 154 154 153 153 152 152 152 151 151 151 151
60 158 156 154 153 152 152 151 150 149 149 149 148 148 148 148
65 156 154 153 151 150 149 148 147 146 146 145 145 144 144 144
70 155 153 151 149 149 147 146 144 143 142 142 141 141 140 140
75 154 152 149 147 146 144 143 141 140 139 138 137 137 136 136
80 153 150 148 145 143 142 140 138 136 135 134 133 132 132 132
85 152 149 146 143 141 139 138 135 133 131 130 129 128 127 127
90 151 147 144 141 139 137 135 131 129 127 126 125 124 123 123
95 150 146 142 139 137 134 132 128 126 124 122 121 120 119 118
100 149 145 141 137 134 132 129 125 122 120 118 116 115 114 113
110 147 142 137 133 130 127 124 119 115 113 111 108 107 105 105
120 144 139 134 129 126 122 119 113 109 106 104 101 99 97 96
130 142 136 131 126 121 118 114 108 103 99 97 94 91 89 88
140 140 133 128 122 118 113 110 103 97 94 91 87 85 82 81
150 138 131 124 119 114 109 105 98 92 88 85 81 78 76 74
160 136 128 121 115 110 106 ‘101 93 87 83 80 75 73 70 68
170 134 126 119 112 107 102 98 89 83 79 75 70 68 64 63
180 131 123 116 109 104 99 94 85 79 74 71 66 63 60 58
190 129 121 113 106 101 95 91 82 75 71 67 62 59 55 54
200 127 118 111 104 98 92 88 79 72 67 63 58 55 51 50
210 125 116 108 101 95 90 85 76 69 64 60 55 52 48 46 ,
220 123 114 lC6 99 92 87 82 73 66 61 57 52 49 45 43
230 122 112 103 96 90 84 80 70 63 58 55 49 46 42 40
240 120 110 101 94 87 82 77 68 61 56 52 47 43 40 38
250 118 108 99 92 85 80 75 65 59 54 50 44 41 37 35
260 116 106 97 89 83 77 73 63 57 52 48 42 39 35 33
270 114 104 95 87 81 75 71 61 55 50 46 41 37 33 31
280 113 102 93 85 79 73 69 59 53 48 44 39 35 32 30
290 111 100 91 84 77 72 67 58 51 46 42 37 34 30 28
300 109 98 89 82 75 70 65 56 49 45 41 36 32 29 27

58
TABLE 6.1 C MAXIMUM PERMISSIBLE BENDING STRESSES, (Ibc ( MPa ),
IN EQUAL FLANGE I-BEAMS OR CHANkELS
( Ckme 6.2.2 )
withfy = 340 MPa, f > 2’0 or $- > 75

D/T-+
8 10 12 14 16 18 20 25 30 35 40 50 60 80 100

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
eY+
4Q !15 214 212 212 211 211 210 210 209 209 209 209 209 209 209
45 !13 211 209 208 207 206 206 205 204 204 204 203 203 203 203
50 !10 208 205 204 203 202 201 199 199 198 198 197 197 197 197
55 !08 204 202 200 198 197 196 194 193 192 191 191 190 190 190
60 !05 201 198 195 193 191 190 188 186 185 185 184 183 183 183
65 !03 198 194 191 188 186 185 181 180 178 177 176 176 175 175
70 !OO 195 190 186 183 181 179 175 173 171 170 169 168 167 167
75 I98 192 186 182 179 176 173 169 166 164 163 161 160 159 159
80 195 188 183 178 174 170 168 163 159 157 156 154 153 151 151
85 93 185 179 174 169 165 162 157 153 1.50 149 146 145 144 143
90 90 182 175 169 165 161 157 151 147 144 142 139 138 136 136
95 .88 179 172 165 160 156 152 145 141 137 135 132 131 129 128
100 85 176 168 162 156 151 147 140 135 131 129 126 124 122 121
110 .80 170 162 154 148 143 138 130 124 120 117 114 112 109 108
120 .76 165 155 147 141 135 130 121 115 110 107 103 101 98 97
130 171 159 149 141 134 128 122 113 106 101 98 93 91 88 87
140 167 154 144 135 127 121 116 105 98 93 90 85 82 79 78
150 163 150 139 l.29 122 115 110 99 92 87 83 78 75 72 70
160 158 145 134 124 116 110 104 93 86 80 77 72 68 65 63
170 155 141 129 120 111 105 99 88 80 75 71 66 63 59 58
180 151 137 125 115 107 100 94 83 76 70 66 61 58 54 53
190 147 133 121 111 103 96 90 79 72 66 62 57 54 50 48
200 144 129 117 107 99 92 86 75 68 62 58 53 50 46 44
210 140 125 113 103 95 88 83 72 64 59 55 50 46 43 41
220 137 122 110 100 92 85 79 69 61 56 52 47 43 40 38
230 134 119 107 97 89 82 76 66 58 53 49 44 41 37 35
240 131 116 104 94 86 79 74 63 56 51 47 42 38 35 33
.250 128 113 101 91 83 76 71 61 53 48 44 39 36 32 31
260 125 110 98 88 80 74 68 58 51 46 42 37 34 31 29
270 122 107 95 86 78 72 66 56 49 44 41 36 32 29 27
280 120 105 93 83 76 69 64 54 47 42 39 34 31 27 25
290 117 102 90 81 73 67 62 52 46 41 37 32 29 26 24
300 115 100 88 79 71 65 60 51 44 39 36 31 28 25 23

59
1s : 806 - 1984
TABLE 6.1 D MAXIMUM PERMISSIBLE BENDING STRESSES, (q,~ l4fPs ),
IN EQUAL FLANGE I-BEAMS OR CHANNELS
( Ckru.w6.2.2 )
withfy = 340 MPa, T< 2’0 and +c 75

8 10 12 14 16 18 20 25 30 35 40 50 60 80 100

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
40 217 216 215 214 214 213 213 213 212 212 212 212 212 212 212
45 215 214 212 211 211 210 210 209 208 208 208 208 208 207 20~
50 213 211 209 208 207 206 206 205 204 203 203 203 203 202 207,
55 211 209 206 205 203 202 201 200 199 198 198 197 197 197 197
60 209 206 203 201 199 198 197 195 193 193 192 191 191 191 190
65 207 203 200 197 195 193 192 189 188 187 186 185 184 184 184
70 205 201 197 194 191 189 187 184 182 181 180 178 178 177 177
75 203 198 194 190 187 184 182 178 176 174 173 172 171 170 169
80 201 195 190 186 183 180 177 173 170 168 167 165 164 163 162
85 199 193 187 183 179 175 173 168 164 162 160 158 157 156 155
90 197 190 184 179 175 171 167 162 158 156 154 151 150 148 148
95 195 187 181 175 171 167 163 157 153 150 148 145 143 142 141
100 193 185 178 172 167 163 159 152 147 144 142 138 137 135 134
110 188 180 172 165 159 155 150 142 137 133 130 126 124 122 121
120 184 175 166 159 152 147 142 133 127 123 120 116 113 110 109
130 180 170 161 153 146 140 135 125 119 114 110 106 103 100 99
140 177 165 156 147 140 134 128 118 111 106 102 97 94 91 89
150 173 161 151 142 134 128 122 112 104 99 95 89 86 83 81
160 169 157 146 137 129 122 117 106 98 92 88 82 79 75 74
170 166 153 142 132 124 117 111 100 92 86 82 76 73 69 67
180 162 149 137 128 120 113 107 95 87 81 77 71 67 63 61
190 L59 145 133 124 115 108 102 91 82 76 72 66 63 59 56
200 155 141 130 120 111 104 98 86 78 72 68 62 58 54 52
210 152 138 126 116 108 100 94 83 74 69 64 58 54 50 48
220 149 135 123 113 104 97 91 79 71 65 61 55 51 47 45
230 146 132 119 109 101 94 88 76 68 62 58 52 48 44 42
240 143 128 116 106 98 91 85 73 65 59 55 49 45 41 39
250 141 126 113 103 95 88 82 70 62 57 52 46 43 38 36
260 138 123 110 100 92 85 79 68 60 54 50 44 40 36 34
270 135 120 108 98 89 82 77 65 58 52 48 42 38 35 32
280 133 117 105 95 87 80 74 63 56 50 46 40 36 32 30
290 130 115 103 93 84 78 72 61 54 48 44 38 35 31 29
300 128 112 100 90 82 76 70 59 52 46 42 37 33 29 27

60
 ISr800-l!J84
TABLE 6.1 E MAXIMUM PERMISSIBLE BENDING STRESSES, Ubo ( -1,
IN EQUAL FLANGE I-BEAMS OR CHANNELS
( Clausa 6.2 2 )

with fy = 400 MPa, f > 2.0 or + > 67

D/l-+

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
8 10 12 14 16 18 20 25 30 35 40 50 60 80 100
“7

40 250 248 247 245 245 244 243 243 242 242 242 241 241 241 241
45 247 244 242 240 239 238 237 236 235 235 234 234 234 233 233
50 244 240 237 234 233 231 230 228 227 227 226 226 225 225 225
55 240 235 232 229 226 224 223 221 219 218 217 216 216 216 215
60 236 231 226 223 220 217 216 212 210 209 208 207 206 206 205
65 233 226 221 217 213 210 208 204 202 200 199 197 197 196 195
70 229 222 216 211 207 203 201 196 193 191 189 188 187 186 185
75 226 217 211 205 200 196 193 188 184 182 180 178 177 175 175
80 222 213 206 199 194 190 186 180 176 173 171 168 167 166 165
85 219 209 201 194 188 183 179 172 167 164 162 159 158 156 155
90 216 205 196 188 182 177 173 165 160 156 154 151 149 147 146
95 212 201 191 183 177 171 166 158 152 149 146 142 140 138 137
100 209 197 187 178 171 165 160 151 145 141 138 135 133 130 129
II0 203 189 178 169 161 155 149 139 133 128 125 121 118 115 114
120 196 182 170 160 152 145 140 129 121 116 1!3 108 106 103 101
130 191 176 163 153 144 137 131 119 112 106 103 98 95 92 90
140 185 169 156 146 137 129 123 111 103 98 94 88 85 82 80
150 179 163 150 139 130 122 116 104 96 90 86 81 77 74 72
160 174 158 144 133 124 116 109 97 89 83 79 74 70 67 65
170 169 152 139 127 118 110 104 92 83 78 73 68 64 61 59
180 165 147 134 122 113 105 97 86 78 72 68 63 59 55 54
190 160 143 129 117 108 100 94 82 74 68 64 58 55 51 49
200 156 138 124 113 104 96 90 78 70 64 60 54 51 47 45
210 152 134 120 109 100 92 86 74 66 60 56 51 47 43 41
?20 148 130 116 105 96 88 82 71 63 57 53 47 44 40 38
230 144 126 112 101 92 85 79 67 60 54 50 45 41 37 36
240 141 123 109 98 89 82 76 65 57 52 47 42 39 35 ‘33
250 137 119 106 95 86 79 73 62 54 49 45 40 37 33 31
260 134 116 103 92 83 76 70 60 52 47 43 38 35 31 29
270 131 113 100 89 81 74 68 57 50 45 41 36 33 29 27
280 128 110 97 86 78 71 66 55 48 43 39 34 31 27 26
290 125 107 94 84 76 69 64 53 46 41 38 33 30 26 24
300 122 105 92 82 74 67 62 52 45 40 36 31 28 25 m

61
IS t 888 - 1984
TABLE 6.1 F MAXIMUM PERMISSIBLE BENDING STRESSES, abc ( MPa),
IN EQUAL FLANGE I-BEAMS OR CHANNELS
( Clause 6.2.2 )

with fy= 400 MPa, -+2.0and+C67

D/T+
hY 8 lo 12 14 16 18 20 25 30 35 40 50 60 80 loo

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
4
40 253 252 250 249 249 248 248 247 247 246 246 246 246 246 246
45 251 248 246 245 244 243 243 242 241 241 240 240 240 240 239
50 248 245 242 240 239 238 237 235 234 234 233 233 233 232 232
55 245 241 238 236 234 232 231 229 227 227 226 225 225 225 224
60 242 237 234 231 228 226 225 222 220 219 218 217 217 216 216
65 239 234 229 225 222 220 218 215 212 211 210 209 208 207 207
70 236 230 225 220 217 214 212 207 205 203 202 200 199 198 198
75 233 226 220 215 211 208 205 200 197 195 193 191 190 189 188
80 230 223 216 210 206 202 199 133, 189 186 185 182 181 180 179
85 227 219 212 205 200 196 192 186 181 178 176 174 172 171 170
90 225 215 207 201 195 190 186 179 174 171 168 165 164 162 161
95 222 212 203 196 190 185 180 172 167 163 161 157 155 153 152
100 219 208 199 191 185 179 175 166 160 156 153 150 148 145 144 .
110 213 202 191 183 176 169 164 154 148 143 140 135 133 130 129
120 208 195 184 175 167 160 154 144 136 131 127 123 120 117 115
130 203 189 177 167 159 152 146 134 126 121 117 111 108 105 103
140 198 183 171 160 152 144 138 126 117 111 107 102 98 95 93
150 193 178 165 154 145 137 131 118 109 103 99 93 89 86 84
160 188 172 159 148 139 131 124 111 102 96 92 85 82 78 76
170 183 167 154 142 133 125 118 105 96 90 85 79 75 71 69
180 179 162 149 137 127 119 112 99 90 84 79 73 69 65 63
190 175 158 144 152 122 114 108 94 85 79 74 68 64 60 58
200 171 153 139 128 118 110 103 90 81 75 70 63 60 55 53
210 167 149 135 123 114 105 99 86 77 70 66 59 55 51 49
220 163 145 131 119 110 102 95 82 73 67 62 56 52 48 45
230 159 141 127 115 106 98 91 79 70 64 59 53 49 44 42
240 156 138 123 112 102 94 88 75 67 61 56 50 46 42 39
250 152 134 120 108 99 91 85 72 64 58 53 47 43 39 37
260 149 131 117 105 96 88 82 70 61 55 51 45 41 37 34
270 146 128 114 102 93 85 79 67 59 53 49 43 39 35 32
280 i43. 125 111 99 90 83 77 85 57 51 47 41 37 33 30
290 140 122 108 97 88 80 74 63 55 49 45 39 35 31 29
300 137 119 105 94 85 78 72 61 53 47 43 37 3% 29 27

62

l
 IS t 800 - 1984

6.2.4 Elastic Critical &ess - If an elastic flexural analysis is not carried

out, the elastic critical stressfOb for beams and plate girders with Ir smaller
than 1x shall be calculated using the following formula:

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
where

= 26.5 x IO’JMPa
Y
( 0% )’ -

k1 - a coefficient to allow for reduction in thickness or breadth of

flanges between points of effective lateral restraint and depends
on #, the ratio of the total area of both flanges at the point of
least bending moment to the corresponding area at the point of
greatest bending moment between such points of restraint.
Values of kl for different values of # are given in Table 6.3.

D’pr$ - as defined in 6.2.2.1.

,
k, - a coefficient to allow for the inequality of flanges, and depends
on W, the ratio of the moment of inertia ofthe compression
flange alone to that of the sum of the moments of inertia of the
flanges, each calculated about its own axis parallel to the y-y
axis of the girder, at the point of maximum bending moment.
Values of k, for different values of o are given in Table 6.4.

Cl, ca= respectively the lesser and greater distances from the section
neutral axis to the extreme fibres.

I, = moment of inertia of the whole section about the axis lying in

the plane of bending ( axis y-y ), and

Ix - moment of inertia of the whole section about the axis normal

to the plane of bending ( x-x axis ).

Values of X and Y are given in Table 6.5 for appropriate values of

D/T and l/r,..

63
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE 6.2 VALUES OF mc CALCULATED FROM feb FOR DIFFERENT VALUES OF fu
tf
( Claw 6.2.3 ) ..
All units in MPa.
8
I
h +
220 23 0 240 250 260 280 300 320 340 360 380 400 420 450 480 510 540
P
20 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13
30 19 19 19 19 19 19 19 19 19 19 19 19 19 19 20 20 20
40 25 25 25 25 25 25 25 2.5 26 26 26 26 26 26 26 26 26

50 30 30 31 31 31 31 31 31 31 32 32 32 32 32 32 32 32

60 36 36 36 36 36 37 37 37 37 37 3% 3% 3% 3% 3% 3% 3%

7Q 41 41 41 41 42 42 42 43 43 43 43 .44 44 44 44 44 44
% 80 45 46 46 46 47 47 4% 4% 4% 4?I 49 49 49 50 50 50 50

90 50 50 51 51 51 52 53 53 54 54 54 55 55 55 56 56 56
100 54 54 55 55 56 57 57 5% 59 59 60 60 60 61 61 62 62
I
,
110 5% 5% 59 60 60 61 62 63 64 64 65 65 66 66 67 67 67 /

120 61 62 63 64 64 65 67 67 6% 69 70 70 71 71 72 72 73

130 65 66 67 67 6% 70 71 72 73 74 74 75 76 76 77 7% 7%

140 6% 69 70 71 72 73 75 76 77 7% 79 80 80 81 82 83 a4

150 71 72 73 74 75 77 79 80 81 82 83 84 a5 a6 87 88 89

160 74 75 77 7% 79 81 82 84 a5 87 88 89 90 91 92 93 94
170 77 7% 80 81 82 84 86 8% 89 91 92 ;3 94 95 97 9% 99

180 79 81 82 84 85 87 89 91 93 94 96 97 9% 100 101 102 103

190 82 %k 85 87 a% 90 93 95 97 9% 100 1.02 102 104 106 107 10%

 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
200 84 86 88 89 91 93 96 98 100 102 103 105 106 108 110 111 113

210 86 88 90 92 93 96 ,99 101 103 105 107 109 110 112 114 116 117

220 89 90 92 94 96 99 102 104 106 109 111 112 114 116 118 120 121

230 90 93 94 96 98 101 104 107 110 112 114 116 118 120 122 124 126

240 92 94 97 99 100 104 107 110 113 115 117 119 121 124 126 128 130

250 94 96 99 101 103 106 110 113 115 118 120 122 124 127 130 132 134

260 96 98 100 103 H)5 108 112 115 110 121 123 126 128 131 133 136 138

270 97 100 102 104 107 111 114 118 121 124 126 129 131 134 137 139 142

280 99 101 104 106 108 113 116 120 123 126 129 132 134 137 140 143 145

290 100 103 lb5 108 110 115 119 122 126 129 132 135 137 141 144 147 149

300 102 104 107 110 112 116 121 125 128 131 135 137 140 144 147 150 153

310 103 106 108 111 114 118 123 127 130 134 137 140 143 147 150 153 156
c 320 104 107 110 113 115 120 125 129 133 136 140 143 146 150 153 157 160

330 105 108 111 114 117 122 126 131 135 138 142 145 148 152 156 160 163

340 106 110 113 115 118 123 128 133 137 141 144 148 151 155 159 163 166

350 108 111 114 117 12a 125 130 134 139 143 147 150 153 158 162 166 169

360 109 112 115 118 121 126 131 136 141 145 149 152 156 161 166 169 172

370 110 113 116 119 122 128 133 138 143 147 151 155 158 163 168 172 175

380 111 114 117 120 123 129 135 140 144 149 153 157 160 166 170 174 178

390 111 115 118 121 125 130 136 141 146 151 155 159 163 168 173 177 181

400 112 116 119 122 126 i32 137 143 148 152 157 161 165 170 175 180 184

420 114 118 121 124 128 134 140 146 151 156 160 165 169 175 180 185 189

115 119 123 126 130 136 142 148 154 159 164 169 173 179 185 190 195
440
( Continued)

l
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE 6.2 VALUES OF U&. CALCULATED FROM f& FOR DWFERENT VALUES OF fy - ~otthf
All units in MPa.
L
fY +
220 230 240 250 260 280 300 320 34@ 3@l 380 400 420 450 480 510 540
f?

460 117 121 124 128 132 138 145 151 157 162 167 172 177 183 189 194 200
-480 118 122 126 130 133 140 147 153 159 165 170 175 180 187 i93 199 204
500, 119 123 127 131 135 142 149 155 162 168 173 178 183 190 197 203 209
520 120 125 129 133 136 144 151 158 164 170 176 181 187 194 201 207 213
540 121 126 130 134 138 145 153 160 166 172 178 184 189 197 204 211 217
560 122 127 131 135 139 147 154 161 168 175 181 187 192 200 208 215 221
580 123 128 132 136 140 148 156 163 170 177 183 i89 195 203 211 218 225
600 124 129 133 137 141 150 157 165 172 179 185 192 198 206 214 222 229
s 620 125 129 134 138 143 151 159 166 174 181 187 194 200 209 217 225 232
6‘lo 126 130 135 139 144 152 160 168 175 183 189 196 202 211 220 228 235
660 126 131 136 140 145 153 161 169 177 i84 191 198 204 214 222 231 238
680 127 132 136 141 145 154 163 171 178 186 193 200 207 216 225 234 242
700 128 132 137 142 146 155 164 172 180 187 195 202 209 218 228 236 244
720 128 133 138 143 147 156 165 173 181 189 196 204 210 220 230 239 247
740 157 166 ~ 174 182 190 198 205 212 222 232 241 250
129 134 139 143 148
760 199 207 214 224 234 244 253
129 134 139 144 149 158 167 175 184 192
780 130 135 140 145 149 159 168 176 185 193 201 208 216 226 236 246 255
800 130 135 140 145 150 159 169 177 186 194 202 210 217 228 238 248 257
850 131 137 142 147 152 161 171 180 188 197 205 213 221 232 243 253 263
900 132 138 143 148 153 163 172 182 191 200 208 216 224 236 247 258 268
950 133 138 144 149 154 164. 174 183 193 202 211 219 227 240 251 262 273
Iooo 134 139 145 150 155~ 165 175 185 195 204 213 222 230 243 255 266 277

.
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
1050 135 140 145 151 156 167 177 187 196 206 215 224 233 246 258 270 281
1 100 135 141 146 152 157 168 178 188 198 207 217 226 235 248 261 273 285

I 150 136 141 147 152 158 168 179 189 199 209 219 228 237 251 263 276 288

1200 136 142 147 153 159 169 180 190 200 210 220 230 239 253 266 279 291

1300 137 143 149 154 160 171 182 192 203 213 223 233 243 257 270 284 297

1400 138 144 149 155 161 .172 183 194 205 215 225 236 246 260 274 288 302

1500 139 144 150 156 162 173 184 195 206 217 228 238 248 263 278 292 306

1600 139 145 151 157 163 174 185 197 208 219 229 240 250 266 281 295 309

1 700 140 146 151 157 163 175 186 198 209 220 231 242 252 268 283 298 313

! 800 140 146 152 158 164 176 187 199 210 221 232 243 254 270 285 301 316

1 900 140 146 152 158 164 176 188 200 211 222 234 245 256 272 287 303 318

2 000 ‘141 147 153 159 165 177 189 200 212 223 235 246 257 273 289 305 321
2 2 200 141 147 154 160 166 178 190 202 213 225 237 248 259 276 292 309 325

2 400 142 148 154 160 166 179 191 203 215 226 238 250 261 278 295 312 328

2 600 142 148 154 161 167 179 191 204 216 227 239 251 263 280 297 314 331

2 800 142 149 155 161 167 180 192 204 216 228 240 252 264 282 299 316 333
3 000 143 149 155 161 168 180 193 205 217 229 241 253 265 283 300 318 335
3 500 143 149 156 162 168 181 194 206 218 231 243 255 267 286 303 321 339

4000 143 150 156 163 169 182 194 207 219 232 244 257 269 287 306 324 342

4 500 144 150 157 163 169 182 195 208 220 233 245 258 270 289 307 326 344 t;
5000 144 150 157 163 170 183 195 208 221 233 246 259 271 290 309 327 346 ”

d 500 144 151 157 163 170 183 196 208 221 234 247 259 272 291 310 328 347 0

6 0‘00 144 151 157 164 170 183 196 209 222 234 247 260 273 291 310 329 348 &
I
g
 _.._“.,--.7- II=‘ -m...- .
*.“, /, “l.*.*_^,“. c_J,I,l~**.“--“I_L._I

IS I 809 - 1984

TABLE 6.3 VALUES OF k, FOR BEAMS WITH CURTAILED FLANGES

( Clause 6.2.4 )
(1, 1.0 0.9 0’8 0.7 0’6 0.5 0’4 0.3 0.2 0.1 0’0
kl I.0 1-O 1’0 0.9 0’8 0.7 0.6 0.5 0’4 0’3 0’2
NOTE - Flanges should not be reduced in breadth to give a value of + lower
than 0.25.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE 6.4 VALUES OF kp FOR BEAMS WITH UNEQUAL FLANGES
( Clause 6.2.4 )
0 1’0 0’9 0’8 0.7 0.6 0’5 0.4 0.3 0.2 0’1 0.0
k, 0.5 0’4 0.3 0.2 0’1 0 -0.2 -0.4 -0.6 -0.8 -1.0

6.2.4.1 Values of fob shall be increased by 20 percent when T/t is

not greater than 2-O and d,/t is not greater than 1 3441 qf; where dl is as
defined in 6.2.2.1 and 1.3 and t the thickness of web.
NOTE - Guidance for calculqting elastic buckling forces may be found in the
references listed in Appendix E.
6.2.5 Beams Bent About the Axis of Minimum Strength ( y-y axis ) - The
maximum permissible bending stress in tension u,-,t or in compression CQO
in beams bent about t,he axis of minimum strength shall not exceed
@66 f,,, where f y is the yield stress of steel.
6.2.6 Angles and Tees - The bending stress in the leg when loaded with
the flange or table in compression shall not exceed O-66f ,,. When loaded
with the leg in compression, the permissible bending stress shall be
calculated from 6.2.3 and 6.2.4 with k8 = - l-0 and I = thickness of leg.
6.3 Bearing Stress -The bearing stress in any part of a beam when
calculated on the net area of contact shall not exceed the value of up
determined by the following formula:
bp = 0.75 fy
where
bp = maximum permissible bearing stress, and
fY = yield stress of steel.
6.4 Shear Stresses
6.4.1 Maximum Shear Stress - The maximum shear stress in a member
having regard to the distribution of stresses in conformity with the elastic
behaviour of the member in flexure, shall not exceed the value 7vm given
below: ~

68
 r&s: 800 - 1984

where
rym = maximum permissible shear stress, and
f,. = yield stress of steel,
6.4.2 Average Shear Stress - The average shear stress in a member
calculated on the cross section of the web ( see 6.4.2.1 ) shall not exceed:

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
a) For unst$ened webs - the value rVa obtained by the formula
rva = 0.4 f,, and
b) For sti$ened webs - the values given in Tables 6.6A, 6.6B and 6.6C
as appropriate for yield stress values 250, 340 and 400 MPa,
respectively.
The values rya for stiffened webs for a steel whose yield stress is
not given in Tables 6.6A, 6.6B and 6.6C shall be determined
by using the following formulae, provided that the average
stress rVQ, shall not exceed O-4 f,,.
i) For webs where the distance between the vertical stiffeners
is less than ‘d’

zoi
- c
.-
TVS = 0.4fy

[
le3
- 1+ 4 (;)‘)
1
ii) For webs where the distance between the vertical stiffeners
is more than ‘d’

%a = 0.4fr 1.3 _

where

rva = maximum permissible average shear stress.

c = distance between vertical stiffeners.
d =
1) For vertically sti$ened webs without horizontal stgeners - the clear
distance between flange angles or, where there.are no flange
angles, the clear distance between flanges, ignoring fillets.
Where tongue plates ( see Fig. 6.1 ) having a thickness of
not less than twice the thickness of the web plate are used,
the depth d shall be taken as the depth of the girder between
the flanges less the sum of the depths of the tongue plates or
eight times the sum of the thickness of the tongue plates,
whichever is less.

69
 _-

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE 6.5 VALUES OF x AND Y FOR CALCULATING f&

( Clam 6.2.4 )
- __I
DIT X r ’
-5:

1
h +
\ + 8 10 12 14 16 18 20 25 30 35 40 50 60 80 100 $
-
40 !484 2222 2066 1965 1897 1849 1814 1759 1728 1709 1697 1683 1675 1.667 1663 1 656
45 ! 103 1856 1708 1612 1546 1499 1465 1411 1380 1362 1349 1335 1327 1319 1315 1 309
50 1822 1590 1449 1357 1293 1248 1214 1161 1131 1113 1101 1086 1078 1070 1067 1 060
55 1 607 I389 1254 1 166 1 105 1061 1028 976 947 929 917 902 894 886 883 876
60 1 437 1 232 1 104 1 020 961 918 886 835 806 788 776 762 754 746 743 736
65 1 301 1 107 985 904 847 806 775 726 697 679 667 653 645 637 634 627
70 1 188 1 005 889 811 757 717 687 638 610 592 581 567 559 551 547 541
2 75 1 094 920 810 735 682 644 615 567 540 522 511 497 489 481 478 471
80 1 014 849 743 672 621 584 556 509 482 465 454 440 432 424 421 414
85 945 788 687 618 570 533 506 461 434 417 406 392 385 377 373 367
90 886 735 639 573 526 491 464 420 394 377 366 353 345 337 334 327
95 833 689 597 534 488 454 428 385 360 343 332 319 311 304 300 294
100 787 649 560 499 455 423 398 356 331 314 304 290 283 275 272 265
110 708 58“ 499 443 402 371 317 307 283 268 257 244 237 229 226 219
120 644 527 451 398 359 330 308 270 247 232 222 209 202 194 191 184
130 591 482 411 361 325 298 277 240 218 204 194 181 174 167 163 157
140 546 444 378 331 297 271 251 217 195 181 172 160 153 145 142 135
150 508 412 350 306 274 249 230 197 177 163 152 142 135 145 124 118
160 474 385 326 284 254 230 212 181 161 148 139 127 121 113 110 104
170 445 360 305 265 236 214 197 167 148 135 126 115 109 102 98 92
180 420 339 286 249 221 200 184 155 137 125 116 105 98 92 88 82

.
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
190 397 320 270 235 208 188 172 145 127 115 107 96 90 83 80 1 73
200 376 304 256 222 197 177 162 136 119 107 99 89 83 76 73 66
210 358 288 243 210 186 168 153 128 112 101 93 82 76 70 66 60
220 341 275 231 200 177 159 145 121 105 94 87 77 71 64 61 55
230 32; 262 220 191 169 152 138 115 99 89 82 72 66 60 56 50
240 312 251 211 182 161 145 132 109 94 84 77 67 62 55 52 46
250 299 241 202 175 154 138 126 104 90 80 73 64 58 52 49 42
260 288 231 194 167 148 133 12 1 99 85 76 69 60 55 48 45 39
270 277 222 186 161 142 127 116 95 82 72 66 57 52 46 42 36
280 267 214 180 155 137 122 111 91 78 69 63 54 49 43 40 34
290 257 207 173 149 132 118 107 88 75 66 60 52 46 41 38 32
300 249 200 167 144 127 114 103 84 72 64 57 49 44 38 35 2g
_lS:808-1984

2 ) For vertically s@ened webs with horizontal sti$eners - as describ-

ed in 6.7.4.3, the clear distance between the tension flanges
( angles, flange plate or tongue plate ) and the horizontal
stiffener.
t = the thickness of the web.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
NOTE 1 - For the minimum thickness of web plates and the design
of web stiffeners, see 6.7.3 and 6.7.4.

NOTE 2 - The allowable stresses given in the Tables 6.6A, 6.6B and
6.6C apply provided any reduction of the web cross section is due only to
rivet holes, etc. Where large apertures are cut in the web, a special analysis
shall be made to ensure that the maximum permissible average shear stresses
laid down in this standard are not exceeded.

NOTE 3 - Compliance with this subclause shall be deemed to satisfy the

requirements of 6.4.1.

6.4.2.1 The cross sections of the web shall be taken as follows:

For rolled I-beams and The depth of the beam multiplied by

channels web thickness

For plate girders The depth of the web plate multi-

plied by its thickness

FIG. 6.1 TONQUE PLATES

72
t,
. .=“ll..___.....
t----“‘-- “’
1 _,.“.^.-1-,_-.
I _ .,-... _^I^. .l_-_---._.._ ..-_.

TABLE 6.6A PERMISSIBLE AVERAGE &EAR STRESS 7va

IN STIFFENED WBBS OF STEEL WITH fy = 250 MPa
( C1au.r~
6.4.2 )

dlt STRESS rva ( MPa ) BORDIFFERENTDISTANCESc BETWEENSTIFFENERS

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
_ __--___------~_* --_----_--_-_--_
‘0*3d 0’4d 0’5d 0.6d 0’7d 0'8d 0.9d I’Od l.ld 1’2d 1.3d 1*4d

zi
100
100
100
100
100
100
100
100
100
100
:::
100
looloo
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100

‘9”:
100

‘:
105 100 100 100 100 100 100 100 100 100 99 98 97

110 100 100 100 100 100 100 100 100 99 96 95

100 100 100 1oc 100 100 100 z:
::; 100 100 100 100 100 100 100 100
98 2: 95 :; ;“;
125 100 100 100 100 100 100 98 97 95 93 92 91

130 100 :I 87
69
135 100 :“o: :z 100 100
100 :: z: z; z:
100 160’ 100 100 99 89
:: 100 loo 100 100 97 ;: :: :: 86 8847 tf

100 89 83 81 80
:;x 100 :!8 loo
100 98 94 t: :: :;
180 100 100 98 2: 92 87 :: 82 80 z :z :f
190 100 100 97 92 :!I 84

200 100 100 95 90 86 82

210 100 99 88 83 sl
220 100 86 801
230 100 tt 90
,“; 84 ;:
I Non-applicable ione.
240 100 95 88 83
250 100 ::
260 100 z: t5” :: -
270 99 90 84 81 I

NOTE - Intermediate values may be obtained by linear interpolation.

73

‘
 TABLE 6.6 B PERMISSIBLE AVERAGE SHEAR T,,,, IN STIFFENED
WEBS OF STEEL WITH fu = 340 MPa

( C1m.w6.4.2 )
0 SPRESA~,,a ( MPa ) BOR DIFFERENTDISTANCESc BETWEENSTIFFENEREI
~--------- F__-h___-- _____ -------~

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
-0.3d 0’4d 0’5d 0’6d 0*7d 0’8d 0’9d 1’Od l’ld l*Zd 1’3d 1*4d 1’5d

75 136 136 136 136 136 136 136 136 136 136

8”: :3”6
136
136
136 136 136 136 136 ::Fi136
136
136
136 136 136
134
136
133
136 136 136 136 136 136 136 136 136

90 136 136 136 136 136 136 136 136 136 135 133 132 131
1:; 136 136 136 136 136 136 136 135 133 131 129 128
136 136 :iz 136 135
105 136 136 136 :t: 136 :z 135 133 132
130 130
128 128
126 :2”; ::3”

110 136 136 136 136 136 135 133 131 128 ;;; 124 122 120
115 136 136 136 136 136 133 131 129 126 121 119 118
ii0 i% 136 136 135 131 129 127 124 121 119 117 115
125 136 136 136 :Ei 133 129 127 125 121 119 116 114 113

130 136 136 136 135 131 127 125 122 119 116 114 ;;; Hz
135 136 136 136 134 129 126 123 120 117 114 111
140 136 136 136 132 127 124 121 118 115 112 109 107 105
150 136 136 135 129 124 120 117 114 110 107 104 102 100

160 136 136 132 126 120 110 95

170
180
136
136
136
135 ET
123
119
117
113
tt2”
108
::9”
105
106
102
E97 lo2
98
93
gg
95
90
3:
87 ::
190 136 133 124 116 110 105 100

200 136 130 121 113 106 101 96

128 118 110 103 97 -
s:“o 136 126 116 107 99 93 I
230 135 123 113 103 96 - Non-applicable zone.

121 110
2: E‘i
260 130
119
116
107
104
270 128 114 102

NOTE-Intermediate values may be obtained by linear interpolation.

74

.
 ts : 690- 19a4
TABLE 6.6 C PERMISSIBLE AVERAGE SHEAR STRESS 7va
IN STIFFENED WEBS OF STEEL WITH fy = 460 MPa
( Clause6.42 )
d/t STREW TV* (MPa ) FOR DIFFERENT DISTANCES c BETWEEN STIFFENERS
r------------ *_----__-------__-_~

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
0*3d 0’4d 0*5d 0’6d 0*7d 0’8d 0*9d I’Od IOld i’2d I’3d 1’4d 1’5d

70 160 160 160 160 160 160 160 160 160 160 XX ;;; 160
75 160 160 160 160 160 160 160 160 160 160 159
160 160 160 160 160 160 160 160 159 157 156
160 160 160 160 160 160 160 158 156 154 152

;; 160 160 160 160 160

160 160 159
160 157
160 157
154 155 152
149 147
151 149
146
100 160 160 160 160 160 157 155 151 ::: 146 144 143
105 160 160 160 160 160 1’Z 154 152 149 146 143 141 139

110
115 160 160 160 160
::“9 159
156 155
152 152
149 ;;; ;;; 143
140 fZ 138
135 ‘36
133
120 160 160 160 154 147 144 ;40 137 134 132 129
125 160 160 160 157 152 t:; 144 141 137 134 131 128 126

130 160 ::: 160 155 150 145 141 139 134 131 128 125 123
135 160 160 153 147 143 139 136 132 128 125 122 120
140 160 160 158 151’ 145 140 136 133 129 125 122 119 116
150 160 160 155 147 141 135 131 128 123 119 115 112 110

160 160 160 151 143 136 130 126 123 117 113 109 106 103

180
170 160 155
158 144
148 135
139 127
132 E 116
121 112
117 106
112 101
107 97
103 93
100 Zl
190 160 152 140 131 123 116 111
-

200 160 149 137 127 118 111 106 I

7in ifx 14li
--- 133 123 114 106 I------
220
___ 157
_-_ 143 i30 il9 109 101 1
230 155 140 126 114 105 I-
Non-applicable zone.
240
-..
2.50
153
ii1
137
134
123
119
110
106
100
96
I1

NOTE - Intermediate values may be obtained by linear interpolation.

75
k, ._. __. . --.

1s I 806 - 1984

6.5 Effective Span of Beams - The effective span of a beam shall be

taken as the length between the centres of the supports, except in cases
where the point of application of the reaction is taken as eccentricity to
the support, when it shall be permissible to take the effective span as the
length between the assumed points of application of reaction.

6.6 Effective Length

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
of Compression Flanges

6.6.1 For simply supported beams and girders where no lateral

restraint of the compression flanges is provided, but where each end of the
beam is restrained against torsion, the effective length ‘ 1 ’ of the
compression ,flanges to be used in 6.2 shall be taken as follows:
a ) With ends of compression flanges unrest- 1 = span
rained against lateral bending ( that is,
free to rotate in plan at the bearings )
b) With ends of compression flanges partially 1 = O-85 X span
restrained against lateral bending ( that is,
not free to rotate in plan at the bearings )
Cl With ends of compression flanges fully 1 = 0.7 X span
restrained against lateral bending ( that is,
not free to rotate in plan at the bearings )
Restraint against torsion can be provided by:
i) web or flange cleats, or
ii) bearing stiffeners acting in conjunction with the bearing of
the beam, or
iii) ‘lateral end frames or other external supports to the ends of
the compression flanges ( see Note below ), or
iv) their being built in to walls.
Where the ends of the beam are not restrained against torsion, or
where the load is applied to the compression flange and both the load and
flange are free to move laterally, the above values of the effective length
shall be increased by 20 percent.
NOTE - The end restraint element shall be capable of safely resisting, in
addition to wind and other applied external forces, a horizontal force acting at the
bearing in a direction normal to the compression flange of the beam at the level of
the centroid of the flange and having a value equal to not less than 2.5 percent of
the maximum force occurring in the flange.

6.6.2 For beams which are provided with members giving effective
lateral restraint to the compression flange at intervals along the span, in
addition to the end torsional restraint required in 6.6.1 the effective length
of the compression flange shall be taken as the maximum distance, centre-
to-centre, of the restraint members.

76

.
 IS rmo - 1984
6.6.3 For cantilever beams of projecting length ‘ L ’ the effective length
( 1 ’ to be used in 6.2 shall be taken as follows:

4 Built-in at the support, free at the end I = 0.85 L

b) Built-in at the support, restrained against 1 = 0.75 L
torsion at the end by continuous construction

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
( see Fig. 6.2A )
Cl Built-in at the support, restrained against 1 = 0.5 L
lateral deflection and torsion at the free end
( see Fig. 6.2B )
4 Continuous at the support, unrestrained against 1=3L
torsion at the support and free at the end
( see Fig. 6.2C )
e) Continuous at the support with partial restraint 1=2L
against torsion of the support and free at the
end ( see Fig. 6.2D )
f 1 Continuous at the support, restrained against l=L
torsion at the support and free at the end
( see Fig. 6.2E )
bT =length of cantilever

If there is a degree of fixity at the free end, the effective length shall
be multiplied by

0.5
oT5 in (b) and (c) above, and by Gin (d), (e) and ( f) above.

6.6.4 Where beams support slab construction, the beam shall be

deemed to be effectively restrained laterally if the frictional or positive
connection of the slab to the beam is capable of resisting a lateral force of
2.5 percent of the maximum force in the compression flange of the beam,
considered as distributed uniformly along the flange. Furthermore, the
slab construction shall be capable of resisting this lateral force in flexure
and shear.

6.6.5 For beams which are provided with members giving effective
lateral restraint of the compression flange at intervals along the span, the
effective lateral restraint shall be capable of resisting a force of 2.5 percent
of the maximum force in the compression flange taken as divided equally
between the number of points at which the, restraint members occur.

6.6.6 In a series of such beams, with solid webs, which are connected
together by the same system of restraint members, the sum of the restraining
forces required shall be taken as 2 percent of the maximum flange force
in one beam only.

77
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
FICL 6.2A CANTILEVERBUILT-IN
AT SUPPORT,RESTRAINEDAGAINST
TORSIONATTHE END

FIG.6.2B CANTILEVERBUILT-IN AT SUPPORT,RESTRAINED

LATERALLY AT THEEND
78
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
FIG. 6.2C CANTILEVERL, FIG. 6.2D CANTILEVERIa
CONTINUOUSAT THE SUPPORT, CONTINUOUSAT THE SUPPORT,
UNRESTRAINEDAGAINSTTORSION PARTIALLYRESTRAINEDAGAW~T
AT THE SUPPORTAND UNRESTRA~NBD TORSIONAT THE SUPPORTAND
AT THE END UNRESTRAINED
AT THE END

TIONS
AT INTERSECTIONS

Fro. 6.2E CANTILEVERSPAN CONTINUOUSAT THE SUPPORT,FULLY

RESTRAINEDAQAINSTTORSIONAT THE SUPPORTAND
UNRESTRAINBDAT THE FREE END
6.6.6.1 In the case of a series of latticed beams, girders or roof trusses
which are connected together by the same system of restraint members,
the sum of the restraining forces required shall be taken as 2b5 percent
of the maximum force in the compression flange plus l-25 percent of this
force for every member of the series other than the first up to a maximum
total of 7.5 percent.

79
L.

6.7 Design of Beams and Plate Girders with Solid Webs

6.7.1 Sectional Projerties - Solid web girders should preferably be

proportioned on the basis of the moment of inertia of the gross~ cross
section with the neutral axis taken at the centroid of that section, but it
shall be permissible to use the net moment of inertia. In arriving at the
maximum flexural stresses, the stresses calculated on the basis of the gross
moment of inertia shall be increased in the ratio of gross area to effective

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
area of the flange section, For this purpose the flange sectional area in
riveted or bolted construction shall be taken to be that of the flange plate,
flange angles and the portion of the web and side plates ( if any ) between
the flange angles; in welded construction the flange sectional area shall be
taken to be that of the flange plates plus that of the tongue plates ( if any )
up to a limit of eight times their thickness, which shall be not less than
twice the thickness of the web. **
6.7.1.1 The effective sectional area of compression flanges shall be
the gross area with d.eductions for excessive width of plates as specified for
compression members ( see 3.5.2.1 and 3.5.2.2 ) and for open holes ( inclu-
ding holes for pins and black bolts ) occurring in a plane perpendicular to
the direction of stress at the section being considered ( see 3.6 ).
The effective sectional area of tension flanges shall be the gross
sectional area with deductions for holes as specified in 3.5.2.1 and 3.6 of
this Code.
The effective sectional area for parts in shear shall be taken as
specified in 6.7.3.4.

6.7.2 Flanges

6.7.2.1 In riveted or bolted construction, flange angles shall form as

large a part of the area of the flange as practicable ( preferably not less
than one-third ) and the number of flange plates shall be kept to a
minimum:
a>Inplateexposed situations where
of the top flange shall
flange plates are used, at least one
extend the full length of the girder,
unl,ess the top edge of the web is machined flush with the flange
angles. Where two or more flange plates are used on the one
flange, tacking rivets shall be provided, if necessary, to comply
with the requirements of 8.10.2 and 8.10.3.
b) Each flange plate shall be extended beyond its theoretical cut-off
point, and the extension shall contain sufficient rivets or welds to
develop in the plate the load calculated for the bending moment
on the girder section ( taken to include the curtailed plate ) at
the theoretical cut-off point.

80
--. _. ,..-._.-._- “_,-._.I_.., . . “_,

xs:8oo-1984

c) The outstand\ of flange plates, that is the projection beyond the

outer line of connections to flange angles, channel or joist flanges,
or, in the case of welded constructions, their projection beyond
the face of the web or tongue plate, shall not exceed the valueb
given in 3.5.2.
d) In the case of box girders, the thickness of any plate, or the
aggregate thickness of two or more plates when these plates are

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
tacked together to form the flange, shall satisfy the requirements
given in 3.5.2.
6.7.2.2 Flange splices - Flange joints preferably should not be
located at points of maximum stress. Where splice plates are used, their
area shall be not less than 5 percent in excess of the area of the flange
element spliced, their centre of gravity shall coincide, as nearly as possible,
with that of the element splfced.’ There shall be enough rivets or welds on
each side of the splice to develop the load in the element spliced plus 5
percent but in no case should the strength developed be less than 50
percent of the effective strength of the material spliced. Xn welded
construction, flange plates shall be joined by complete penetration butt
welds, wherever possible. These butt welds shall deveIop the full strength
of the plates.
6.7.2.3 Connection of jlanges to web - The flanges of plate girders shall
be connected to the web by sufficient rivets, bolts or welds to transmit the
maximum horizontal shear force resulting from the bending moments in
the girder, combined with any vertical loads which are directly applied to
the flange.

6.7.2.4 Disbersion of load through JIange to web - Where a Ioad is

directly applied to a top flange, it shall be considered as dispersed
uniformly at an angle of 30 degrees to the horizontal.
6.7.3 Web Plates
6.7.3.1 Minimum thickness - The thickness of the web plate shall be
not less than the following:
a) For unstiffened webs: the greater of
-
4 2/ Tvap cam and “;_&$_- but not less than i.
816
where
dl = depth of web as defined in 1.3, and
%a, cal = calculated average stress in the web due to shear
force.

81

.
rsrsoo-1984

b) For vertically stiffened webs: the greater of

l/180 of the smallest clear panel dimension

and d y’-
-!-_& but not less than -&-
200

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
3 200

4 For webs stiffened both vertically and horizontally with a

horizontal stiffener at a distance from the compression flange
equal to 2/5 of the distance from the compression flange to the
neutral axis: the greater of

l/l80 of the smaller dimension in each panel,

and da
_ V~ but not less than &
4 000

4 When there is also a horizontal stiffener at the neutral axis of

the girder: the greater of

l/180 of the smaller dimension in each panel,

and !!6?&& but not less than -%

400

In (b), (c) and (d) above, dz is twice the clear distance from the
compression flange angles, or plate, or tongue plate to the neutral
axis.

In the case of welded crane gantry plate girders intended for

carrying cranes with a lifting load of 15 tonnes or more, the
thickness of web plate shall be not less than 8 mm.

The minimum thickness of web plates for different yield stress

values are given in Table 6.7 for information.

NOTE- In no case shall the greater clear dimension of a web panel exceed
270 f, nor the lesser clear dimension of the same panel exceed 180 t, where t is
the thickness of the web plate.

6.7.3.2 Riveted construction - For girders in exposed situations and

which do not have flange plates for their entire length, the top edye
of the web plate shall be flush with or above the angles, as specified ‘o;-
the engineer, and the bottom edge of the web plate shall be flush with or
set back from the an;Tles, as specified by the engineer.

6.7.3.3 Welded construction -- The gap between the web ;llatc’s and
flange plates shall be kept to a minimum, and for fillet weld:; .shall not
exceed 1 mm at any point before welding.

82

.
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
l’ABLE 6.7 MINIMUM THICKNESS OF WEB

( Clause 6.7.3.1 )

Minimum Thickness of Web for Yield Stressfy ( in MPa ) of

y-------_-_____ ---_-h-____, -- ,
fY 220 230 240 250 260 280 300 320 340 360 380 400 420 450 480 510 540

ds
----- dr ds da ds de
185 (79 174 169 -ialp
d,&y ds ds ds da 4 da da j’e_ & Js_ & 4, ds dr 4 ds 4
4ooo zz 250 250 %Y 248 239 %l 224 217 211 ‘205 %% 195 x 183 -i?? 172

z drcy dp dz da da dt da _&_ 5 ds dt ds A_ de d, j-a_ pI

da
6 400 &)- 400 hoo -@%- 396 382 370 358 348 338 328 320 312 302 292 284 276
 6.7.3.4 E$ctive sectionalarea
a) Web of #ate girder - The effective cross-sectional area shall be
taken as the full depth of the web plate multiplied by the
thickness.
NOTE -Where webs are varie in thickness in the depth of the section
by the use of tongue plates or the Ii e, or where the proportion of the web

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
included in the flange area ia 25 pert
“%, t or more of the overall depth, the
above approximationis not permissible&nd the maximum shear stress shall
be computed.
b) Rolled beam.rand channels - The effective cross-sectional area for
shear shall be taken as the full depth of the beam or channel
multiplied by its web thickness. For other sections the maxi-
mum shear stress shall be computed from the whole area of the
cross section, having regard to the actual distribution of shear
stress.
c) Webs which have openings larger than those normally used for
rivets or other fastenings require s cial analysis to ensure that
the permissible stress as specific % in this standard are not
exceeded.
6.7.3.5 Splices in webs -“Splices in the webs of the plate girders and
rolled sections shall be designed to resist the shears and moments at the
spliced section.
In riveted construction, splice plates shall be provided on each side
of the web. In welded construction, web splices shall preferably be made
with complete penetration butt welds.
6.7.3.6 Where additional plates are re.quired to augment the strength
of the web, they shall be placed on each side of the web and shall be
equal in thickness. The proportion of shear force, assumed to be resisted
by these plates shall be limited by the amount of horizontal shear which
they can transmit to the flanges through their fastenings, and such re-
inforcing plates and their fastenings shall be carried beyond the points
at which they become theoretically necessary,
6.7.4 Intermediate Web Sti$cnersfor Plate Girders,
6.7.4.1 General - When the thickness of the web is less than the
limits specified in 6.7.3.1 (a) vertical stiffeners shall be provided through-
out the length of the girder. When the thickness of the web is less than
the limits specified in 6.7.3.1 (b) horizontal stiffeners shall be provided in
addition to the vertical stiffeners.
In no case shall the greater unsupported clear dimension of a web
Dane1 exceed 270 t nor the lesser unsupported clear dimension of the .same
panel exceed 180 t, where t is the thickness of the web plate.

84
 6.7.4.2 Vertical ,sti$eners - Where vertical stiffeners are required, they
shall be provided throughout the length of the girder at a distqce apart
not greater than l-5 d and not less than 0*33 d, where d is the depth as
defined in 6.4.2 ( definition 1 ). ‘Where horizontal stiffeners are provided
d in mm shall ‘be taken as’the clear distance between the horizontal
stiffener and the tension flange ( farthest flange ) ignoring fillets. These
vertical stiffeners shall be designed so that I is not !ess than

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
ds -x ts
-. l-5 x 7

where
I = the moment of inertia of a pair of stiffeners about the
centre of the web, or a single stiffener about the face of the
web,
t = the minimum required thickness of the web, and
c = the maximum permitted clear distance between vertical
stiffener for thickness t.
NOTE- If the thickness of the web is made greater, or the spacing of stiffeners
made smaller than that required by the atandard, the moment of inertia of the
stiffener need not be correspondingly increased.
Intermediate vertical stiffeners may be joggled and may be single or
in pairs placed one on each side of the web. Where single stiffeners are
used, they should preferably be placed alternatively on opposite sides of
the web. The stiffeners shall extend from flange to flange, but need not
have the ends fitted to provide a tight bearing on the flange.
6.7.4.3 Horizontal sti$eners - Where horizontal stiffeners are used in
addition to vertical stiffeners, they shall be as follows:
4 One horizontal stiffener shall be placed on the web at a distance
from the compression flange equal to 215 of the distance from the
compression flange to the neutral axis when the thickness of the
web is less than the limits specified in 6.7.3.1 (b). This stiffener
shall be designed so that I is not less than 4c.ts where I and t
are as defined in 6.7.4.2 and c is the actual distance between the
vertical stiffeners;
b) A second horizontal stiffener ( single or double ) shall be placed
at the neutral axis of the girder when the thickness of the web ‘is
less than the limit specified in 6.7.3.1 (c). This stiffener shall be
designed so that I is not less than ds.ts where ds also in mm, I
and t are as defined in 6.7.4.2 and ds is as defined in 6.7.3.1;
Cl Horizontal web stiffeners shall extend between vertical stiffeners
but need not be continuous over them; and
4 Horizontal stiffeners may be in pairs arranged on ‘each side of
the web, or single.

85
IS t 806 - 1984

6.7.4.4 Outstand of sti$eners - Unless thesouter edge of each stiffener

is continuously stiffened, the outstand of all stiffeners from the web shall
256~
be not more than - for sections and 12 t for flats where t is the

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
4fF
thickness of the section or flat.
6.7.4.5 External forces on intermediate sti$eners - When vertical inter-
mediate stiffeners are subjected to bending moments and shears due to
eccentricity of vertical loads, or the action of transverse forces, the moment
of inertia of the stiffeners given in 6.7.4.2 shall be increased as shown
below:
a) Bending moment on stiffener due to eccentricity of vertical loading
bith respect to the vertical axis of the web:

increase of I = 150MDacm4., and

Et
b) Lateral loading on stiffener:
0.3 VDS
Increase of I = Et - cm4
,
where
M = the applied bending moment, KNm;
D = overall depth of girder, in.mm;
E = Young’s modulus, 2 x 10s MPa;
t = thickness of web, mm; and
V = the transverse force in KN to be taken by the stiffener
and deemed to be applied at the compression flange of
the girder.
6.7.4.6 Connections of intermediate sti&zers to web - Intermediate
vertical and horizontal stiffeners not subjected to external loads shall be
connected to the web by rivets or welds, so as to withstand a shearing
force, between each component of the stiffener and the web of not less
than

where
t = the web thickness in~@rn,‘and
*l’ h = the outstand of stiffener in mm.

For stiffeners subjected to external ,loads, the shear between the web
and stiffeners due to these loads shall be added to the above values.

86
 IS : 800 - 1984

6.7.5 Load Bearing Web St$eners

6.751 All sections - For any section, load bearing stiffeners
shall be provided at points of concentrated load ( including points of
support ) where the concentrated load or reaction exceeds the value of
aa~.z.B
where

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
aa = the maximum permissible axial stress for colunins as
given under 5.1 for a slenderness ratio $-LIT

t = web thickness;
B = the length of the stiff portion of the bearing plus the addi-
tional length given by dispersion at 45’ to the level of the
neutral axis, pIus the thickness of the stating angle, if any.
The stiff portion of a bearing is that length which cannot
deform appreciably in bending and shall not be taken as
greater than half the depth of beam for simply supported
beams and the full depth of the beams continuous over a
bearing; and
dl = clear depth of web between root E”:ts.

Load bearing stiffeners shall be symmetrical about the web, where

possible.

6.7.5.2 Plate girders - ,Tn addition to the requirements of 6.7.5.1,

load bearing stiffness shall be prsvided also at the supports where
either:
a) the web is overstressed in shear [ see 6.7.3.1 (a)], or
b) the web is otherwise overstressed at support or at the web
connection.

6.7.5.3 Design of load bearing stijhers

a) Load bearing stiffeners shall be designed as columns assuming the

section to consist of fhe pair of stiffeners together with a Iength
of web on each side of the cenere line of the stiffeners and equal,,
where available, to 20 .times the web thickness. The radius of
gyration shall be taken about the axis parallel to the web of the
beam or girder, and the working stress shall be in accordance
with the appropriate allowable value for a compression member
assuming an effective length equal to O-7 of the length of the
stiffeners;

87

‘.

.
 b) The outstanding legs of each pair-of stiffeners shall be so propor-
tioned that the bearing stress on that part of their area clear of
the root of the flange or flange angles or clear of the welds does
not exceed the bearing stress specified in 6.3;
Stiffeners shall be symmetrical about the web, where possible and

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
at points of support shall project as nearly as practicable to the
outer edges of the flanges;
4 Load bearing stiffeners shall be provided with sufficient rivets
or welds to transmit to the web the whole of the concentrated
load;
e) The ends of load bearing stiffeners shall be fitted to provide a
tight and uniform bearing upon the loaded flange unless welds or
rivets designed to t#ansmit the full reaction or load are provided
between the flange and stiffener. At points of support this require-
ment shall apply ,at both flanges;
f > Bearing stiffeners shall not be joggled and shall be solidly packed
throughout; and
EC)For plate girders, where load bearing stiffeners at supports are the
solemeans of providing restraint against torsion ( see 6.6.4 ) the
moment of inertia, 1, of the stiffener about the centre line of the
web plate, shall be not less than
DST R

where
D - overall depth of the girder,
f - maximum thickness of compression flange,
R = reaction of the beam at the support, and
W - total load on the girder between supports.
In addition, the bases of the stiffeners in conjunction with the bear-
ing of the girder shall be capable of resisting a moment due to the horizon-
tal force specified in the Note under 6.6.1.
6.8 Box Girders - The design and detailing of box girders shall be such
as to,give, full advantage of its higher load carrying capacity. The diaph-
ragms and horizontal stiffeners should conform to 6.7.3 and 6.7.4.
6.8.1 All diaphragms shall be connected such as to transfer the resultant
shears to the web and flanges.
6.8.2 Where the concentrated or moving load does not come directly on
top of the web, the local effect shall be considered for the design of flanges
and the diaphragms.

88
6.9 Purlins

6.9.1 All purlins shall be designed in accordance with the requirements

for undsed bean& ( see 6.2.1 and Table 3.1 ), and the limitations of
bending stress based on lateral instability of the compressicn flange and
the limiting deflection specified under 3.13 may be waived for the design

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
of purlins. The maximum fibre stress shall not exceed the values
specified in 6.2.1 except as provided under 3.9 for increase of stress.
The calculated deflections should not exceed those,permitted for the type
of roof cladding used. In calculating the bending moment advantage may
be taken of the continuity of the purlin over supports. The bending
stresses about the two axes should be determined separately and
checked in accordance with 7.1.1. Open web purlins shall be designed as
trusses.

6.9.2 Angle @urlins of steel copforming to Grades Fe 410-O. Fe 410-S or

Fe 4 10-W and slofies not exceeding,3@’ Pitch - As an alternate to the general
design procedure given in 6.9.1 angle purlins of roofs with slopes not
exceeding 30 degrees may be designed, if the following I :quirements which
are based on a minimum imposed load of 0.75 kN/ms are fulfilled:

4 The width of leg or the depth of the purlin in the plane

appropriate to the incidence of the maximum load or maximum
component of the load is not less than L/45;

b) The width of the other leg or width of the purlin is not less
than L/60;

C>The maximum bending moment in a purlin may be taken as F

where W is the total distributed load on the purlin including
wind load. The loads shall be assumed as acting normal to the
roof in which case the bending about the minor axis may be neg-
lected. L shall be taken as distance centre-to-centre of the rafters
or other supports of the purlins; and

4 Under the bending moment calculated as in (c)‘above, the maxi-

mum fibre stress shall not exceed the appropriate vahre of gb,r or cbt
given in 6.2 except as provided under 3.9 for increase of stresses.
The calculated deflection should not exceed those permitted for
the type of cladding used.

6.10 Side and End Sheeting Rails - Side and end sheeting rails shall be
designed for wind pressures and vertical loads, if any; and the require-
ments of, as regards limiting deflection and lateral stability of beams, the
same provisions as given in 649.1 shall apply.

89
18 : 800 - 1984

SECTION 7 COMBINED STRESSES

7.1 Combination of Direct Stresses

7.1.1 Combined Axial ,Compression and Bending - Members subjected to

axial compression and bending shall be proportioned to satisfy the follow-
ing requirements:

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
However, if the ratio ‘e ’ is less than 0.15, the following expres-

sion may be used in lieu of the above:

cat, 081. u”;.,“,“’ 1 ““;;o;l- 6 1.(I
+
1 QBO
The value of (2bCXand to be used in the above formulae shall
@boy

each be lesser of the values of the maximum permissible stresses bbC given
in Section 6 for bending about the appropriate axis.
b) At a suppbrt and using the values bbCxand obey at the support:
uac>Cal @box, 081.
---+
0*6Of y+ flbox

For an’ encased strut where an allowance

is made for the force
uac, OSl.
carried by the concrete in accordance with 10.1.1 the ratio of ----
GAO
shall be replaced by the ratio of the calculated axial force on the strut to
the maximum permissible axial force determined as per 10.1.2.
7.1.2 Combined Axial Tension and Bending - A member subjected to both
axial tension and bending shall be proportioned so that the following
condition is satisfied:
Uat, 081. ubtx> oal. %ty, O&l.< ]
---+
O*60fY + 0*66fY, 0.66 fv

7.1.3 Symbols - The symbols used in 7.1.1 and 7.1.2 shall have the
following meaning:
uao, 081. = calculated average axial compressive stress
@at, Cal. - calculated average axial tensile stress
ubc, 081. = calculated bending compressive stress in extreme fibre
@bt. 081. = calculated bending tensile stress in extreme fibre

90
@a0 permissible axial compressive stress in the member subject
to axial compressive load only
permissible axial tensile stress in the member subject to
axial tensile load only
permissible bending compressive stress in extreme fibre

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
ubo
flbt permissible bending tensile stress in extreme fibre
GE
foo elastic critical stress in compression - --
As
slenderness ratio in the plane of bending

%Y = represent x-x and Y-y planes

c, = a coefficient whose value shall be taken as follows:
a) For member in frames where side sway is not prevented:
C, ‘5 0.85
b) For members in frames where side sway is prevented and
not subject to transverse loading between their supports
in the plane of bending:
CDl e= 0.6 - 0.4 e 2 0.4
NOTE 1 - f3is the ratio of mallt-r to the larger moments at
the ends of that portion of the b braced member in the plane of
bending under consideration.

NOTE 2 - $ is positive yhen fhe member is bent in reverse

curvature and negative when It is bent in single curvature.

c) For members in frames where Aide sway is prevented in,

the plane of loading and subjected to transverse loading
between their supports; the value of C, may be determin-
ed by rational analysis. In the absence of such analysis,
the following values may be used:
For members whose ends are restrained against rotation
C, = 0.85
For members whose ends are unrestrained against rotation
c, 5 1.00
7.1.4 Bending and Shear - Irrespective of any increase in the germissi-
ble stress specified in 3.9, the equivalent stress ue, oer., due to co-e\xistent
bending ( tension or compression ) and shear stresses obtained from the
formula given in 7.1.4.1 shall not exceed the value:
be - 0.9f,
where
~a p maximum permissible equivalent stress.

91
L.,. _ -_-..i. _

7.1.4.1 The equivalent stress ue, ,,ar. is obtained from the following
formula:
@BPO&&l.
= debt*, Cal* + 37Vma>
081. Or

=t/ ebo’, oal. + 37~12, oal.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
7.1.5 Combined, Bearing, Bending and Shear Stresses - Where a bearing
stress is combined with tensile or compressive, bending and shear stresses
under the most unfavourable condition of loading, the equivalent
stress be, oal. obtained from the following formulae, shall not exceed
Qe = 0*9f,.
Oe3 081. = dubt’, ml* + up’* oal* + ubt, osl. up, calm+ 3 Tvrn’,oal-
or *
Qe, Or&l.- d/Qboa, oal. $ upa,
oal. $ ubo, 081. up, oal. + 3T~rn2,cal.
+ 7.1.6 In 7.1.4 and 7.1.5 ubt, oa1.Gbbo, oar.; Tvm, oar. and up, oal.are the
numerical values of the co-existent bending ( compression or tension ), shear
and bearing stresses. When bending occurs about both axes of the
member, ubt. cal and ebC, oar. shall be,taken as the sum of the two calculat-
ed fibre stresses. ue is the maximum permissible equivalent stress.

SECTION 8 CONNECTIONS

8.0 Ge era1 - As much of the work of fabrication as is reasonably

practica le shall be completed in the shops where the steel work is
fabricateB .

8.1 Rivet& Close Tolerance Bolts, High Strength Friction Grip

Fasteners,;Black Bolts and Welding - Where a connection is subject
to impact or‘vibration or to reversal of stress ( unless such reversal is due
solely to wind ) or where for some special reason, such as continuity in
rigid framing or precision in alignment of machinery-slipping of bolts is
not permissible! then rivets, close tolerance bolts, high strength friction
grip fasteners or welding shall be used. In all other cases bolts in clearance
holes may be used provided that due allowance is made for any
slippage.

8.2 Compositti Connections - In any connection which takes a force

directly communicated to it and which is made with more than one type
of fastening, only rivets and turned. and fitted bolts may be considered as
acting together to share the load. In all other connections sufficient
number of one type of fastening shall be provided to communicate the
entire load for which the connection is designed.

92
 IS:88811884

8.3 Members Meeting at a Joint - For triangulated frames designed

on the assumption of pin jointed connections, members meeting at a joint
shall, where practicable, have their centroidal axes meeting at a point; and
wherever racticable the centre of resistance of a. connection shall be on
the line o P action of the load so as to avoid an eccentricity moment on the
connections.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
8.3.1 However, where eccentricity of members or of connections is
present, the members a+ the connections shall provide adequate resistance
to the induced bending moments.

8.3.2 Where the design is based on non-intersecting members at a joint

all stresses arising from the eccentricity of the members shall be calculated
and the stresses kept within the limits specified in the appropriate clause
of this code.

8.4 Bearing Brackets - Wherever practicable, connections of beams to

columns shall include a bottom bracket and top cleat. Where web cleats
are not provided, the bottom bracket shall be capable of carrying the
whole of the load.

8.5 Gussets - Gusset plates shall be designed to resist the shear, direct
and flexural stresses acting on the weakest or critical section. Re-entrant
cuts shall be avoided as far as practicable.

8.6 Packings

8.6.1 Rivets or Bolts Through Packings- Number of rivets or bolts carrying

calculated shear through a packing shall be increased above the number
required by normal calculations by 2.5 percent for each 2.0 mm thickness
of packing except that, for packings having a thickness of 6 mm or less, no
increase need be made. For double shear connections packed on both
sides, the number of additional rivets or bolts required shall be determined
from the thickness of the thicker packing. The additional rivets or bolts
should preferably be placed in an extension of the packing.

8.6.2 Packings in Welded Construction - Where a packing is used between

two parts, the packing and the welds connecting it to each part shall be
capable of transmitting the load between the parts. Where the packing is
too thin to carry the load or permit the provlsion of ade uate welds, the
load shall be transmitted through the welds alone, the we1%s being increas-
ed in size by an amount equal to the thickness of the packing.

8.663 Packing Subjected to Direct Compression only _- Where properly fitted

packings are subjected to direct compression only, the provisions
under 8.6.1 and 8.6.2 shall not apply.

93
L

IS t 888 - 1984

8.7 Separators and Diaphragms - Where two or more rolled steel joists
or channels are used side by side to form a girder, they shall be connected
together at intervals of not more than 1 500 mm except in the case of gril-
lage beams encased in concrete, where suitable provision shall be made to
maintain correct spacing. Bolts and separators may be used provided that

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
in beams having a depth of 300 mm or more, not fewer than 2 bolts are
used with each separator. When loads are required to be carried from
one beam to the other or are required to be distributed between the beams,
diaphragms shall be used, designed with sufficient stiffness to distribute
the load.
8;8 Lug Angles
8.8.1 Lug angles connecting a channel-shaped member shall, as far as
possible, be disposed symmetrically with respect to the section of the
member.
868.2 In the case of angle members, the lug: angles and their connec-
tions to the gusset or other supporting member shall be capable of develop
ing a strength not less than 20 percent in excess of the force in the
outstanding leg of the angle, and the attachment of the lug angle to the
angle member shall be capable df developing 40 percent in excess of that
force.
8i8.3 In the case of channel members and the like, the lug angles and
thei’r connection to the gusset or other supporting member shall be cap-
able of developing a strength of not less than 10 percent in excess of the
force not accounted for by the direct connection of the member, and the
attachment of the lug angles to the member shall be capable of developing
20 percent in excess of that force.
8.8;4 In no case shall fewer than two bolts or rivets be used for attach-
ing the lug angle to the gusset or other supporting member.
8.8.5 The effective conxiection of the lug angle shall, as far as possible
terminate at the end of the member connected, and the fastening of the
lug angle to the timber shall perferably start in advance of the direct
connection of the member to the gusset or other supporting member.
8.8.6 Where lug angles are used to connect an angle member the whole
area of the member shall be taken as effective notwithstanding the require-
ments’of Section 3 and Section 5 of this code.
8.9 Permissible Stresses in Rivets and Bolts
8.9.1 Calculation of Stresses - In calculating shear and bearing stresses
the effective diameter of a rivet shall be taken as the hole diameter and
that of a bolt as its nominal diameter. In calculating the axial tensile
stress in a rivet the gross area shall be used and in calculating the axial
tensile stress in a bolt or screwed tension rod the net area shall be used.

94
 ISr808-1984

8.9.2 Gross and Net Areas of Rivets and Bolts

8.9.2.1 The gross area of a rivet shall be taken as the cross-sectional
area of the rivet hole.
8.9.2.2 The net sectional area of a bolt or,screwed tension rod shall
be taken as the area of the root of the threaded part or cross-sectional area

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
of the unthreaded part whichever is lesser.
NOTE-The net sectional areas of bolts are given in IS : 1364-1967 and
IS : 1367-1967.
8.9.3 Area of Rivet and Bolt Holes - The diameter of a rivet hole shall be
taken as the nominal diameter of a rivet plus 1.5 mm for rivets of nominal
diameter less than or equal to 25 mm, and 2.0 mm for rivets of nominal
diameter exceeding 25 mm, unless otherwise specified. The diameter of a
bolt hole shall be taken as the nominal diameter of the bolt plus I.5 mm
unless specified otherwise.
8.9.4 Stresses in Rivets, Bolts and Welds
8.9.4.1 The calculated stress in a mild steel shop rivet or in a bolt of
property class 4.6 ( see IS : 1367-1967 ) shall not exceed the values given
in Table 8.1.

TABLE 8.1 MAXIMUM PBRMISSIBLE STRESS IN RIVETS AND BOLTS ~-

DESORIPTION or AXIAL TENSION, utf, SEIEAR, f,f BEARING, up!
FASTENERS
(1) (2) (3) (4)
Mpa MPa MPa
Power-driven rivets 100 100 300
Hand-driven rivets 80 80 250
Close tolerance. and 120 100 300
turned bolts
Bolts in clearance holes 120 80 250

8.9.4.2 The permissible stress in a high tensile steel rivet shall be

those given in Table 8.1 multiplied by the ratio of the tensile strength
of the rivet material to the tensile strength as specified in IS : .I 148-1982
NOTE - For field rivets the permissible stresses shall be reduced by 10 percent.
8.9.4.3 The permissible stress in a bolt ( other than a high strength
friction grip bolt ) of property class higher than 4.6 shall be those given
in Table 8.1 multiplied by the ratio of its yield stress or 0.2 percent
proof stress or 0.7 times its tensile strength, whichever is the lesser, to
235 MPa.
8.9.4.4 The calculated bearing stress of a rivet or bolt on the parts
connected by it shall not exceed : (a) the valuef Y for hand driven rivets or
bolts in clearance holes, and (b) the value 1.2 f, for power driven rivets
or close tolerance and turned bolts. fy is the yield stress of the connected
parts.

95
A‘ .

ISr80@- 1984

Where the end distance of a rivet or bolt ( that is, the edge distance
in the direction in which it bears ) is less than a limitfof twice the effec-
tive diameter of the rivet or bolt, the permissible bearing stress of that
rivet or bolt on the connected part shall be reduced in the ratio of the
actual and distance to that limit.
8.9.4:5 Combined shear and tension - Rivets and bolts subject to both

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
shear and axial tension shall be so proportioned that the shear and axial
stresses calculated in accordance with 8.9.1 do not exceed the respective
allowable stresses rVf and utf and the expression WY OSl.‘ Rf, oa1.
-+---
I w nf 1
does not exceed 1.4.
8.9.4.6 High strength friction grit bold - The provisions contained
in 8;9.4:1 to 8.9L4.5 do not apply to high strength friction grip bolts, which
shall be used in conformity with I,S : 4000-1,967.
8.9.4.7 Welds - Permissible stress in welds shall be as specified in ’
IS : 816-1969 and IS : 1323-1982.
8.10 Rivetsand Riveting
Pitch
8.10.1 of Rivets

a) Minimum Pitch - The distance between centres of rivets should be

not less than 2.5 times the nominal diameter of the rivet.
b) Maximum Pitch
i) The distance between centres of any two adjacent rivets
( includ.ing tacking rivets ) shall not exceed 32 t or 300 mm,
whichever is less, where t is the thickness of the thinner
outside plate.
ii) The distance between centres of two- adjacent rivets, in a line
lying in the direction of stress, shall not exceed 16 t or
200 mm, whichever is less in tension members and 12 t or
200mm, whichever is less in compression members. In the
case of compression members in which farces are transferred
through butting faces, this distance shall not exceed 4.5 times
the diameter of the rivets for a distance from the abutting
faces equal to 1.5 times the width of the member.
iii) The distance between centres of any two consecutive rivets in
a line adjacent and parallel to an edge of an outside plate
shall not exceed (100 mm + 4 t ) or 200 mm, whichever
is less in compression or tension members.
iv) When rivets are staggered at equal intervals and the gauge
does not exceed 75 mm, the distances specified in (ii) and
(iii) between centres of rivets, may be increased by 50
percent.

96
 IS:rwo-1984

8.10.2 Edge Distance

4 The minimum distance from the centre of any hole to the edge of
a plate shall be not less than that given in Table 8.2.

b) Where two or more parts are connected together, a line of rive&

or bolts shall be provided at, a distance of not more than
37 mm + 4 t from the nearest edge, where t is the thickness in

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
mm of the thinner outside plate. In the case of work not
exposed to weather, this may be increased to 12 t.

TABLE 8.2 EDGE DISTANCE OF HOLES

DIAXETER OF HOLE DISTANCETO SHEAREDOR DISTANCETO ROW,

HAND FLAME CUT EDGE MACHINE FLAXE CUT,
SAWN OR PLANEDEDGE
(1) (2) (3)
mm mm mm
13.5 and below 19 17
15’5 25 22
17-5 29 25
19’5 32 29
21.5 32 29
23.5 38 32
25.5 44 38
29-o 51 44
32’0 57 51
35-o 57 51

8.10.3 Tacking Rivets - In cases of members covered under I).lO.l(b)(ii),

when the maximum distance between centres of two adjacent rivets
astspecified in 8.10.l(b)( ii ) is exceeded, tacking rivets not subjected to
calculated stress shall be used.

8.10.3.1 Tacking rivets shall have a pitch in line not exceeding

32 times the thickness of the outside plate or 300 mm, whichever is less.
Where the plates are exposed to the weather, the pitch in line shall not
exceed 16 times, the thickness of the outside plate or 200 mm, whichever
is less. In both cases, the lines of rivets shall not be apart at a distance
greater than these pitches.

8.10.3.2 All the requirements specified in 8.10.3.1 shall apply to

compression members generally, subject to the stipuIation in this code
affecting the design and construction of compression members.

97
IS:800 -1984

8.10.3.3 In tension members composed of two flats, angles, channels

or tees in contact back-to-back or separated back-to-back by a distance not
exceeding the aggregate thickness of the connected parts, tacking rivets,
with solid distance pieces where the parts are separated, shall be provided
at pitch in line not exceeding 1 000 mm.

8.10.3.4 For compression members covered in Section 5, the tacking

rivets shall be at a pitch in line not exceeding 600 mm.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
8.10.4 Counterjunk Heads - For countersunk heads, one-half of the depth
of the countersinking shall be neglected in calculating the length of the
rivet in bearing. For rivets in tension with countersunk heads, the tensile
value shall be reduced by 33.3 percent. No reduction need be made in
shear.

8.10.5 Long Grip Rivets - Where the grip of rivets carrying calculated
loads exceed 6 times the diameter of the holes, the number of rivets required
by normal calculation shall be increased by not less than one percent for
each additional 1.5 mm of grip; but the grip shall not exceed 8 times the
diameter of the holes.

8.11 Bolts an-d Bolting

8.11.1 Pitches, Edge Distances for Tacking Bolts - The requirements for
bolts shall be the same as for rivets given in 8.10 and its sub-clauses.

8.11.2 Black Bo!ts - The dimepsions of black bolts shall conform, to

those given in IS : 1363-1967.

8.11.3 (Jose Tolerance Bolts - Close tolerance bolts shall conform to

IS : 1364-1967.

8.11.4 Turned Barrel Bolts - The nominal diameter of the barrel shall be
in multiples of 2 mm and shall be at least 2 mm larger in diameter than
the screwed portion.

8.11.5 Washers - Washers with perfectly flat faces should be provided

with all close tolerance bolts and turned barrel bolts. Steel or malleable
cast iron tapered washers shall be provided for all heads and nuts bearing
on bevelled surfaces.

8.11.6 Locking of Nuts - Wherever there is risk of the nuts becoming

loose due to vibration or reversal of stresses, they shall be securely locked.

8.12 Welds and Welding - For requirements of welds and welding,

reference shall be made to IS : 816-1969 and IS: 9595-1980.

98
 fS : so0 - 1984

SECTION 9 PLASTK DESIGN

9.1 ,GeneraY
9.1.1 The structure or part of a structure may be proportioned on the
basis of plastic design based on their maximum strength using the
provisions- contained in this section. Reference may also be made to
SP (6) 6-1972.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
9.1.2 The requirement of this standard regarding the maximum per-
missible stress shall be waived for this method. However, the design shall
comply with all other requirements of this standard.
9.13 Members subjected to heavy impact and fatigue shall not be
designed on the basis of plastic theory.
9.1.4 Steel conforming to Grade Fe 410-O of IS : 1977-1975 shall not
be used when the structure is designed on the basis of plastic theory.
1
9.2 Design
9.2.X Load Factors - Structures or portions of structures proportioned
using plastic design shah have sufficient strength as determined by plastic
analysis to support the working loads multiplied by load factors as given
below:
Working Loads Load Factor,
Min
Dead load 1.7
Dead load + imposed load 1.7
Dead load + load due to wind or seismic I.7
forces
Dead load + imposed load + load due l-3
to wind or seismic forces
9.2.2 Dejection - Deflections under working loads shall be in accor-
dance with relevant provisions of this code.
9.2.3 Beams

9.2.3.1 The calculated maximum moment capacity, &I,, of a beam

shall be
Mp = &fv
where
&, 5 plastic modulus of the section, and
f,, = yield stress of the material.

99
 _ ._ ._ ___..
__...I

IS I 888 - 1984

9.2.3.2 Plastic properties of Indian Standard medium weight beams

are given in Appendix F for information.
9.2.4 Tension Members - The calculated maximum load capacity Pat of
a tension member shall be Pat = 0.85 AS&
where

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
A, = effective cross-sectional area of the member, and
f y= yield stress of the steel.
9.2.5 Struts - The calculated maximum load capacity P,, of a strut
shall be
P *,, = 1.7 A, sac
where sac is the maximum permissible stress in axial compression as
given in 5.1 using an effective length 2 equal to the actual length L.
9.2.6 Members Subjected to Combined Bending and Axial Forces ( Beam-
Column Members )
9.2.6.1 The calculated maximum moment capacity Mpe of a member
subjected to combined bending and axial forces, where PIP, exceeds 0.15,
shall be reduced below the value given in 9.2.3 and it shall satisfy the
following requirements:

b) Slender struts -A member where sin addition to exceeding O-15

F
l+P-ho shall not be assumed to contain plastic
also exceeds l$-@n
hinges although it shall be permissible to design the member as
an elastic part of a plastically designed structure. Such a member
shall be designed according to the maximum permissible stress
requirements satisfying:

1.0

c) Stocky struts - A strut not covered in (b) above shall satisfy

P = an axial force, compressive or tensile in a member;

MPG = maximum moment ( plastic ) capacity acting in the beam-
column;

100

.
 1S : 888 - 1984

M r = plastic moment capacity of the section;

M 0= lateral buckling strength in the absence of axial load
= M, if the beam column is laterally braced;
P Bc = buckling strength in the plane of bending if axially loaded
( without any bending moment ) and if the beam column

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
is laterally braced, as per 9.2.5.1;

pe - Euler load = Fyt;s for the plane of bending;

Pr = yield strength of axially loaded section = As. f y;

A s = effective cross-section area of the member;
C, = a coefficient as defined in 7.1.3;
Y = radius of gyration about the same axis as the applied
moment;
he = characteristic slenderness ratio

PyT= -.
PO
L
‘IET
z.
E ’
B re ratio of end moment, each measured in the same rota-
tional direction and chosen with the numerically large
amount in the denominator ( @ range from + 1 for
double curvature, 0 for one end pinned, to - 1 for single
curvature ) ; and
L= actual strut length.
9.2.6.2 A member assumed to contain plastic hinges and subjected
to combined b&ding and axial compression with PIPy not exceeding O-15
0.6 + 0.4 p
shall have a value of PIP, not exceeding --- where X0and p are as
A0
defined above.

9.2.7 Shear - The calculated maximum shear capacity Vr of a beam

or a beam-column shall be
vv = 0.55 A, fy

where A, is the effective cross-sectional area resisting shear for

calculating the average shear stress or the maximum shear capacity of the
members.

9.2.8 Stabili~ - The elastic buckling load of a frame or its components

designed on the basis of plastic theory shall be at least three times the
plastic collapse load. If an accurate estimate of the elastic buckling load is

101
 .._-._“__._.

not available, this provision shall be deemed to be satisfied for frames of

up to three storeys if the compressive force P, in each member does not
exceed:

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
for ‘buckling in any direction, where the effective length 1 is determined
according to 5.2.
For frames of over three storeys, the calculated plastic collapse
load shall include an assessment of the moment caused by the possible
combination of high axial force and transverse deflection.
9;2i9 Minimum Thickness
9;2;9J Compression Outstands- A flange or other compression element
required to participate in a plastic hinge shall not project beyond its outer
most point of attachment by more than 136. T,/df?

Where Tl is the thickness of flange of a section or plate in compres-

sion or the aggregate thickness of plates if connected in accordance with
Section 8.
For the purpose of this clause, web stiffeners at plastic hinges shall
be proportioned as compression elements.
9.2.9.2 lJn.q‘ported widths - The distance between adjacent parallel
lines of attachment of a compression flange or another compression ele-
ment to other parts of member, when such flanges or elements are required
to participate in a plastic hinge action, shall not exceed 512. Tl/+/ic
Where T1 is as defined in 9.269.1.
9.2.9.3 Webs in shear - If the depth dl of a web subjected to shear
688.t
and required to participate in a plastic hinge exceeds -= then the
Jfp.
compressive axial force P on the member shall not exceed the value

P = P, o*‘io- +LL&
( )
The maximum permissible value of dl in &y plastic hinge zone shall
_ 1120.t

9.2.9.4 Web under bending and compression - When the web is subjected
to bending and compression, the following conditions shall be satisfied:

a) Where 2 exceeds 0.27, then the depth dl shall not

PV
exceed

102
 b) When $ is less than or equal to O-27, then the depth dI shall

)I.
”

dfudfu
(PY
s

1120 1600 P t
- - - -

9.2.10Lateral Bra&g

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
9.2.10.1 Members shall be adequately braced to resist lateral and
torsional displacement at the plastic hinge locations associated with failure
mechanism. Lateral bracing mass be dispensed within the region of the
last hinge to form in the failure mechanism assumed as the basis for
proportioning the given member.

a) If the length along the member in which the applied

9.2.10.2
moment exceeds O-85. M,, is less than or equal to
640v.rY
at least one critical flange support shall be pro-
-Tz ’
vided within or at the end’of this length and the spacing
of the adjacent supports shall not exceed 96Ov.r,,/J fT

b) If the length along the member rn which the applied

moment exceeds 0.85 M, is greater than or equal to
64Ov.r,
the critical flange shall be supported in such a
Am-’
manner that no portion of this length is unsupported for
a distance of more than 9.
Y

c) Lateral restraints for the remaining elastic portions of

the member shall be designed in accordance with Sections
4 and 5 as appropiate, using ,stresses derived from the
plastic bending moments multiplied by 1.7.

In this clause M, shall be assumed as Mp or MP0 as appropriate.

v may be taken as unity or calculated by the following expression:

1.5
’ = dl + (d/8)

where e is the ratio of the rotation at the hinge point to the relative
elastic rotation of the far ends of the beam segment containing the plastic
hinge.

103
IS I 890 - 1984

NOTE - The lateral restraints provided by this clause will ensure that a section
delivers its full moment and deformation capacity; This may be too great for some
design circumstances. With the approval of the appropriate authority the design
engineer may use the methods which allow a reduced amount of bracing to be used,
provided that this reduction is justified by rational and widely accepted means and
that any associated reductions in moment and deformation capacity are fully

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
considered in the design.

9.2.11 Web Stifening

9.2.11.1 Excessive shear forces - Web stiffeners or doubler plates
shall be provided when the requirements of 9.2.7 are not met, in which
case the stiffeners or doubler plates shall be capable of carrying that
portion of the force which exceeds the shear capacity of the web.
9.2.11.2 Concentrated loads - Web stiffeners shall be provided at
points on a member where the concentrated force delivered by the flanges
of another member framing into it will produce web crippling opposite
the compression flange or high tensile stress in the connection of the ten-
sion flange. This requirement shall be deemed to be satisfied if web
stiffeners are placed:
a) opposite the compression flange of the other member when
A!
tCZ-,, + 5k
b) opposite the tension flange of the other member when
7-~<0~4.c/~~
where
t = thickness of web to be stiffened,
k = distance from outer face of flange to web toe of fillet of
member to be stiffened,
7-b = thickness of flange delivering concentrated load,
7-r = thickness of flange of member to be stiffened, and
Ai = area of flange delivering concentrated load.
The area of such stiffeners, Aa, shall be such that
A&Ax - t ( lb + 5k )
The ends of such stiffeners shall be fully butt welded to the inside
face of the flange adjacent to the concentrated tensile force. It shall be
permissible to fit the stiffeners against the inside face of the flange adjacent
to the concentrated compression force without welding. When the con-
centrated force is delivered by only one beam connected to an outside face
0f.a strut, the length of the web stiffener shall extend for at least half the
depth of the member, and the welding connecting it to the web shall be
sufficient to develop a force off ,..A,t.

104
 IS : 800 - 1984

9.2.11.3 Plastic hinges - Web stiffeners shall be provided at all

plastic hinges where the applied load exceeds 0.06 A, f ,,, where A, is as
explained in 9.2.7.
9.2.12 Load Cabacities of Connections - The calculated load capacities of
welds, bolts and rivets shall be taken as l-7 times the values calculated

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
using permissible stress specified in 8.9.4.
9.3 Connections and Fabrication
9.3.1 Connections

9.3.1.1 All connections which are essential to the continuity, assumed

as the basis of the design analysis shall be capable of resisting the moments,
shears and axial loads to which they would be subjected by either full or
factored loading.
9.3.1.2 Corner connections ( haunches ), tappered or curved for
architectural reasons shall be so proportioned that the full plastic bending
strength of the section adjacent to the connection may be developed.
9.3.1.3 Stiffeners shall be used, as required, to preserve the flange
continuity of interrupted members at their junction with other members
in a continuous frame. Such stiffeners shall be placed in pairs on
opposite sides of the web of the member which extends continuously
through the joint.

9.3i2 Fabrication - The provisions of Section 11 with respect to work-

manship shall govern the fabrication of structures, or portions of structures,
designed on’ the basis of maximum strength, subject to the following
limitations:
a) The use of sheared edges shall be avoided in locations subject to
plastic hinge rotation at factored loading. If used they shall be
finished smooth by grinding, chipping or planing.
b) In locations subject to plastic hinge rotation at factored loading,
holes for rivets or bolts in the tension area shall be sub-punched
and reamed or drilled full size.

SECTION 10 DESIGN OF ENCASED MEMBERS

10.1 Encased Columns

10.1.1 Conditions of Design - A member may be designed as an encased

column when the following conditions are fulfilled:
a) The member is of symmetrical I-shape or a single I-beam for
channels back-to-back, with or without flange plates;

105

.
 b) The overall dimensions of the steel section do not exceed
750 x 450 mm over plating where used, the larger dimension
being measured parallel to the web;

4 The column is unpainted and is solidly encased in ordinary dense

concrete, with 20 mm aggregate ( unless solidity can be obtained

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
with a larger aggregate ) and of grade designation M 15, Min
( see IS : 456-1978 ).

4 The minimum width of solid casing is equal to 6e + 100 mm,

where 6, k the width of the steel flange in millimetres;

4 The surface and edges of the steel column have a concrete cover
of not less than 50 mm;

f) The casing is effectively reinforced with steel wires. The wire

shall be at least 5 mm in diameter and the reinforcement shall
be in the form of stirrups or binding at not more than 150 mm
pitch so arranged as to pass through the centre of the c:overing
of the edges and outer faces of the flanges and supported by
longitudinal spacing bars not less than four in number; and

g) Steel cores in encased columns shall be accurately machined at

splices and provisions shall be made for alignment of column.
At the column base provision shall be made to transfer the load
to the footing at safe unit stresses in accordance with IS : 456-
1978.

10.1.2 Design of Member

10.1.2.1 The steel section shall be considered as carrying the entire

load but allowance may be made by assuming the radius of gyration ‘ I ’
of the column section about the axis in the plane of its web to be
0.2 (b, + 100) mm, where b, is the width of the steel flange in millimetres.
The radius of gyration about its other axis shall be taken as that of the
uncased section.

1O.li2.2 The axial load on the encased column shall not exceed 2
times that which would be permitted on the uncased section, nor shall the
slenderness ratio of the uncased section ,for its full length centre-to-centre
of connections exceed 250.

10.L2.3 In computing the allowable axial load on the encased strut,

the concrete shall be taken as assisting in carrying the load over its rec-
tangular cross section, any cover in excess of 75 mm from the overall
dimensions of the steel section of the cased strut being ignored.

106
 10.1.2.4The allowable compressive load P in case of encased
columns shall be determined as follows:
P = AsoQm + A&
where

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
-%O, A, = cross-sectional area of steel and concrete, and
flBO>Qo = permissible stresses in steel and concrete in com-
pression.
NOTE - This clause does not apply to steel struts of overall sectional dimen-
sions greater than 1 000 mm x 500 mm, the dimension qf 1 000 mm being measured
parallel to the web or to box sections.

10.2 Encased Beams

10.2.1Conditions of Design - Beams and girders with equal flanges may
be designed as encased beams when the following conditions are fulfilled:
4 The section is of single web and I-form or of double open
channel form with the webs not less than 40 mm apart;
b) The beam is unpainted and is solidly encased in ordinary ldense
concrete, with 10 mm aggregate ( unless solidity can be
obtained with a larger aggregate ), and of a grade designation
M 15, Min ( see IS : 456-1978 );
The minimum width of solid caring = ( 6, + 100 ) mm, where
b, is the width of the steel flange in mm;
The surface and edges of the flanges of the beam have a concrete
cover of not less than 50 ~-IQ; and
The casing is effectively reinforced with steel wire of at least
5 mm diameter and the reinforcement shall be in the form of
stirrups or binding at not more than 150 mm pitch, and so
arranged as to pass through the centre of the covering to the
edges and soffit of the lower flange.
10.2.2Design of Member - The steel section shall be considered as carry-
ing the entire load but allowance may be made for the effect of the con-
crete on the lateral stability of the compression flange. This allowance
,
should be made by assuming for the purpose of determining the permissi;
ble stress in compression that the equivalent moment of inertia ( Ir )
about the y-y axis is equal to A.r,S, where A is the area of steel section and
yYmay be taken as 0.2 ( be + 100 ) mm. Other properties required for
referring to 6.2 may be taken as for the uncased section. The permissible
bending stress so determined shall not exceed l-5 times that permitted for
the uncased section.
NOTE - This clause does not apply to beams and girders having a depth greater
than 1 000 mm, or a width greater than 500 mm or to box sections.

?I?

.
IS t 888 - 1984

SECTION 11 FABRICATION AND ERECTION

11.1 General - Tolerances for fabrication of steel structures shall

conform to IS : 72 15- 1974. Tolerances for erection of steel structures shall
conform to the Indian Standard.* For general guidance on fabrication
by welding, reference may be made to IS : 9595-1980.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
11.2 Fabrication Procedures

11.2.1 Straightening - All material shall be straight and, if necessary,

before being worked shall be straightened and/or flattened by pressure,
unless required to be of curvilinear form and shall be free from twists.
11.2.2 Clearances - The erection clearance for cleated ends of members
connecting steel to steel should preferably be not greater than 2-O mm at
each end. The erection clearance at ends of beams without web cleats
should be not more than 3 mm at each end, but where, for practical
reasons, greater clearance is necessary, suitably designed seatings should
be provided.
11.2.2.1 Where black bolts are used, the holes may be made not
more than l-5 mm greater than the diameter of the bolts, unless otherwise
specified by the engineer.

11.2.3 Cutting
11.2.3.1 Cutting may be effected by shearing, cropping or sawing. Gas
cutting by mechanically controlled torch may be permitted for mild steel
only. Gas cutting of high tensile steel may also be permitted provided
special care is' taken to leave sufficient metal to be removed by machining
so that all metal that has been hardened by flame is removed. Hand
flame cutting may be permitted subject to the approval of the inspector.
11.2.3.2 Except where the material is subsequently joined by welding,
no loads shall be transmitted into metal throug,h a gas cut surface.
11.2.3.3 Shearing, cropping and gas cutting, shall be clean,
reasonably square, and free from any distortion, and should the inspector
find it necessary, the edges shall be ground afterwards.

11.2.4 Holing
11.2.4.1 Holes through more than one thickness of material for
members, such as compound stanchion and girder flanges shall, where
possible, be drilled after the members are assembled and tightly clamped
or bolted together. Punching may be permitted before assembly, provided

*Tolerances for erection of steel structures ( underprepurulion).

108
 lstmJ=1984

the holes are punched 3 mm less in diameter than the required size and
reamed after assembly to the full diameter. The thickness of material
punched shall be not greater than 16 mm. For dynamically loaded
structures, punching shall be avoided.

11.2.4.2 When holes are drilled in one operation through two or

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
more separable parts, these parts, when so specified by the engineer, shall
be separated after drilling and the burrs removed.

11.2.4.3 Holes in connecting angles and plates, other than splices,

also in roof members and light framing, may be punched full size through
material not over 12 mm thick, except where required for close tolerance
bolts or barrel bolts.

11.2.4.4 Matching holes for rivets and black bolts shall register
with each other so that a gauge of 1.5 mm or 2.0 mm ( as the case may be
depending on whether the diameter of the rivet or bolt is less than or
more than 25 mm ) less in diameter than the diameter of the hole will pass
freely through the assembled members in the direction at right angle to
such members. Finished holes shall be not more than 1.5 mm or 2.0 mm
(as the case may be ) in diameter larger than the diameter of the rivet
or black bolt passing through them, unless otherwise specified by the
engineer.
11.2.4.5 Holes for turned and fitted bolts shall be drilled to a
diameter equal to the nominal diameter of the shank or barrel subject to
H8 tolerance specified in IS : 919-1963. Preferably parts to be connected
with dose tolerance or barrel bolts shall be firmly held together by packing
bolts or clamps and the holes drilled through all the thicknesses at one
operation and subsequently reamed to size. All holes not drilled through
all thicknesses at one operation shall be drilled to a smaller size and
reamed out after assembly. Where this is not practicable, the parts shall
be drilled and reamed separately through hard bushed steel jigs.
11.2.4.6 Hole’s for rivets or bolts shall not be formed by gas cutting
process.

11.3 Assembly - The component parts shall be assembled and aligned in

such a manner that they are neither twisted nor otherwise damaged, and
shall be so prepared that the specified cambers, if any, provided.

11.4 Riveting
11.4.1 Rivets shall be heated uniformly throughout their length,
without burning or excessive scaling, and shall be of sufficient length to
provide a head of standard dimensions. They shall, when driven,

109
completely fill the holes and, if countersunk, the countersinking shall be
fully filled by the rivet, any protrusion of the countersunk head being
dressed off flush, if required.
11.4.2 Riveted members shall have all parts firmly drawn and held
together before and during riveting, and special care shall be taken in
this respect for all single-riveted connections. For multiple riveted

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
connections, a service bolt shall be provided in every third or fourth hole.
11.4.3 ‘Wherever practicable, machine riveting shall be carried out by
using machines of the steady pressure type.
11.4.4 All loose, burned or otherwise defective rivets shall be cut out
and replaced before the structure is loaded, and special care shall be taken
to inspect all single riveted connections.
11.4.5 Special care shall be taken in heating and driving long rivets.

11.5 Bolting
11.541Where necessary, washers shall be tapered or otherwise suitably
shaped to give the heads and nuts of bolts a satisfactory bearing.
11.5.2 The threaded portion of each bolt shall project through the nut
at least one thread.
11.5.3 In all cases where the full bearing area of the bolt is to be
developed, the bolt shall be provided with a washer of sufficient thickness
under the nut to avoid any threaded portion of the bolt being within the
thickness or the parts bolted together.
11.6 Welding
11.6.1 Welding shall be in accordance with IS : 816-1969, IS : 819-1957,
IS : 1024-1979,IS : 1261-1959, IS : 1323-1982 and IS : 9595-1980, as
appropriate.
11.6.2 For welding of any particular type of joint, welders shall give
evidence acceptable to the purchaser of having satisfactorily completed
appropriate tests as described in any of the Indian Standards - IS : 817-
1966, IS : 1393-1961, IS : 7307 ( Part 1 )-1974, IS : 7310 ( Part 1 )-I974
and IS : 7318 ( Part 1 )-1974, as relevant.
11.7 Machining of Butts, Caps a-d Bases
11.7.1 Column splices and butt joints of struts and compression. members
depending on contact for stress transmission shall be accurately machined
and close-butted over the whole section with a clearance not exceeding
O-2 mm locally at any place. In column caps and bases, the ends of shafts
together with the attached gussets, angles, channels, etc, after riveting
together should be accurately aachined so that the parts connected\ butt

1.10
-.. .--.-
-._-_-1.“_-. .-. -.._.. ._.... . . _.... ” .._..
____l^.._.,_____ . .I..^_

IS : 888 19s4 l

over the entire surfaces of contact. Care should be taken that these
gussets, connecting angles or channels are fixed with such accuracy that
they are not reduced in thickness by machining by more than 2.0 mm.
11.7.2 Where sufficient gussets and rivets or welds are provided to
transmit the entire loading ( see Section 5 ) the column ends need not be

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
machined.

11.7.3 Ends of all bearing stiffeners shall be machined or ground to fit

tightly at both top and bottom.
11.7.4 Slab Bases and Caps - Slab bases and slab caps, except when cut
from material with true surfaces, shall be accurately machined over the
bearing surfaces and shall be in effective contact with the end of the stan-
chion. A bearing face which is to be grouted direct to a foundation
need not be machined if such face is true and parallel to the upper face.

11.7.5 To facilitate grouting, holes shall be provided where necessary

in stanchion bases for the escape of air.
11.8 Solid Round Steel Columns
11.8.1 Solid round steel columns with shouldered ends shall be provided
with slab caps and bases machined to fit the shoulder, and shall be tightly
shrunk on or welded in position.

11.8.2 The tolerance between the reduced end of the shaft and the
hole, in the case of slabs welded in position, shall not exceed 0.25 mm.

11.8.3 Where slabs are welded in position, the reduced end of the shaft
shall be kept just sufficiently short to accommodate a filletweld around the
hole without weld-metal being proud of the slab.

11.8.3.1 Alternatively, the caps and bases may be welded direct to

the column without bearing or shouldering.

11.8.3.2 All bearing surfaces of slabs intended for metahto-metal

contact shall be machined perpendicular to the shaft.

11.9 Painting

11.9.1 Painting shall be done in accordance with IS : 1477 ( Part 1 )-

1971 and IS : 1477 ( Part 2 )-1971.

11.9.2 All surfaces which are to be painted, oiled or otherwise treated

shall be dry and thoroughly cleaned to remove all loose scale and loose
rust.

11.9.3 Shop contact surfaces need not be painted unless specified.

If so specified, they shall be brought together while the paint is still wet.

111
ISt800-1984

11.9.4Surfaces not in contact, but inaccessible after shop assembly,

shall receive the full specified protective treatment before assembly. This
does not apply to the interior of sealed hollow sections.
11.9.5Chequered plates shall be painted but the details of painting
shall be specified by the purchaser.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
11.9.6In the case of surfaces to be welded, the steel shall not be paint-
ed or metal coated within a suitable distance of any edges to be welded
if the paint specified or the metal coating would be harmful to welders or
impair the quality of the welds.

11.9.7 Welds and adjacent parent metal shall not be painted prior to
deslagging, inspection and approval.
11.9.8 Parts to be encased in concrete shall not be painted or oiled.

11.10 Marking
11.10.1Each piece of steel work shall be distinctly marked before
delivery, in accordance with a marking diagram, and shall bear such
other marks as will facilitate erection.
11.11 Shop Erection
11.11.1The steelwork shall be temporarily shop erected complete or as
arranged with the inspector so that accuracy of fit may be checked before
despatch. The parts shall be shop assembled with sufficient numbers of
parallel drifts to bring and keep the parts in place.
11.11;2 In the case of parts drilled or punched, through steel jigs with
bushes resulting in all similar parts being interchangeable, the steelwork
may be shop’erected in such position as arranged with the inspector.

11.12 Packing - All projecting plates or bars and all ends of members
at joints shall be stiffened, all straight bars and plates shall be bundled,
all screwed ends and machined surfaces shall be suitably packed and all
rivets, bolts, nuts, washers and small loose parts shall be packed separately
in cases so as to prevent damage or distortion during transit.

11.13 Inspection and Testing

lL13.1 The inspector shall have free access at all reasonable times to
those parts of the manufacturer’s works which are concerned with the
fabrication of the steelwork and shall be afforded all reasonable facilities
for satisfying himself that the fabrication is being undertaken in accordance
with the provisions of this standard.
11.13.2 Unless specified otherwise, inspection shall be made at the place
of manufacture prior to despatch and shall be conducted so as not to
interfere unnecessary with the operation of the work.

112
 18 : 888 - 1984

11.13.3 The manufacturer shall guarantee compliance with the

provisions of this standard, if required to do so by the purchaser.
11.13r4 Should any structure or part of a structure be found not to
comply with any of the provisions of this standard, it shall be liable to

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
rejection. No structure or part of the structure, once rejected shall be
resubmitted for test, except in cases where the purchaser or his authorised
representative considers the defect as rectifiable.
11;13;5 Defects which may appear during fabrication shall be made
good with the consent of and according to the procedure laid down by the
inspector.
lL13.6 All gauges and templates necessary to satisfy the inspector shall
be supplied by the manufacturer. The inspector, may, at his discretion,
check the test results obtained at the manufacturer’s works by independent
tests at the Government Test House or elsewhere, and should the material
so tested be found to be unsatisfactory, the costs of such tests shall be borne
by the manufacturer, and if satisfactory, the costs shall be borne by the
purchaser.
11~14 Site Erection

11.14;1 Plant and Equijment - The suitability and capacity of all plant
and equipment used for erection shall be to the satisfaction of the
engineer.
11.14.2 Storing and Handling - All structural steel should be so stored
and handled at the site that the members are not subjected to excessive
stresses and damage.

11.14.3 Setting Out - The positioning and levelling of all steelwork, the
plumbing of stanchions and the placing of every part of the structure with
accuracy shall be in accordance with the approved drawings and to the
satisfaction of the engineer.

11.14.4 Security During Erection

11.14.4.1 For safety precautions during erection of steel structures

reference shall be made to IS : 7205-1973.

11.14.4.2 During erection, the steelwork shall be securely bolted or

otherwise fastened and, when necessary, temporarily braced to provide
for all load to be carried by the structure during erection including those
due to erection equipment and its operation.

llr14.4.3 No riveting, permanent bolting or welding should be done

until proper alignment has been obtained.

..
IS : 800 - 1984

llil4.5 Field Connections

Field riveting - Rivets driven at the site shall be heated
11.14.5.1
and driven with the same care as those driven in the shop.
11.14.5.2 Field bolting - Field bolting shall be carried out with the
same care as required for shop bolting.
lli14.5;3 Field welding - All field assembly and welding shall be

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
executed in accordance with the requirements for shop fabrication except-
ing such as manifestly apply to shop conditions only. Where the steel has
been delivered painted, the paint shall be removed before field welding,
for a distance of at least 50 mm on either side of the joint.
lL15 Painting After Erection
11.15.1 Betbre painting of such steel which is delivered unpainted, is
commenced, all surfaces to be painted shall be dry and thoroughly
cleaned from all loose scale and rust.
11~15.2 The specified protective treatment shall be completed after
erection. All rivet and bolt heads and the site welds after de-slagging
shall be cleaned. Damaged or deteriorated paint surfaces shall first be
made good with the same type of paint as the shop coat. Where specified,
surfaces which will be in contact after site assembly shall receive a coat of
paint ( in addition to any shop priming ) and shall be brought together
while the paint is still wet.
11.15.3 Where the steel has received a metal coating in the shop, this
coating shall be completed on site so as to be continuous over any welds
a:ld site rivets or bolts, but subject to the approval of the engineer protec-
tion may be completed by p@nting on site. Bolts which have been galvaniz-
ed or similarly treated are exempted from this requirement.
11.15.4 Surfaces which will be inaccessible after site assembly shall
receive the full specified protective treatment before assembly.
11.15.5 Site painting-should not be done in frosty or foggy weather, or
when humidity is such as to cause condensation on the surfaces to be :
painted.
11.16 Bedding of Stanchion Bases and Bearings of Beams and
Girders on Stone, Brick or Concrete ( Plain or Reinforced )
11.16.1 Bedding shall be carried out with portland cement, grout or
mortar, as described under 11.16.4 or fine cement concrete in accordance
with IS : 456-1978.
11.16.2 For multi-storeyed buildings, this operation shall not be carried
out until a sufficient number of bottom lengths of stanchions have been
properly lined, levelled and plumbed and suffkient floor beams are in
position.

114
 11.16.3 Whatever method is employed the operation shall not be
carried out until the steelwork has been finally levelled and plumbed,
the stanchion bases being supported meanwhile by steel wedges; and im-
~~n~ez.ly before grouting, the space under the steel shall be thoroughly
.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
11.16.4 Bedding of structure shall be carried out with grout or mortar
which shall be of adequate strength and shall completely fill the space to be
grouted and shall either be placed under pressure or by ramming against
fixed supports.

SECTION 12 STEEL-WORK TENDERS AND CONTRACTS

12.1 General Recommendations

12.1.1 A few recommendations are given in Appendix G for general

information.

115
 MiWO-19S4

APPENDIX A
( Clause3.3.2 )

CHART SHOWING HIGHEST MAXIMUM TEMPERATURE

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY

The territorial waters of India extend into the sea to a dietance of twc!ve nautical miles
measured from thcs appropriate base line.
Bred upon Survey of India map with,thc permission of the Surveyor General of India.
Q Government of India Copyright 195.
Responsibility for the correctness of internal details rests with the publishers.
116
 IS : 800 l 1984

APPENDIX B
( Clause 3.3.2 )
CHART SHOWING LOWEST MINIMUM TEMPERATURE

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY

The territorial waters of India extend into the sea to a distance of twelve nautical miles
measured from the appropriate base line.
Based upon Survey of India map with the permission of the Surveyor General of India.
6 Government of India Copyright 1995.
Responsibility for the correctness of internal details rests with the publishers.

117
’ IS:800-1984

APPENDIX C
( Clause 5.2.2)

EFFECTIVE LENGTH OF COLUMNS

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
C-l. In the absence of more exact analysis, the.effective length of columns
in framed structures may be obtained from the ratio I/&, of effective length
1 to unsupported length L given in Fig. C-l when relative displacement
of the ends of the column is prevented and in Fig. C-2 when relative
lateral displacement of the ends is not prevented. In the later case, it is
recommended that the effective length ratio l/L may not be taken to be
less than 1.2.

In Fig. C-l and Fig. C-2, fi1 and & are equal to z xll --
L x0 + 2 Kb

where the summation is to be done for the members framing into a joint
at top and bottom respectively; & and xb being the flexural stiffnesses for
the column and beam, respectively.

118
 LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
f$ : 808 - 1984

SUPPLIED BY BOOK SUPPLY BUREAU

LENGTHRATIOSFORA COLUMN
IN A FRAMEWITHNo SWAY

119
EFFECTIVE
FIG. C-l
 HINGED I. 0

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
FIXED 0 HINGED
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
P2-
z
li:

C-2
FIG.' EFFECTIVE LENQTH RATIOS FOR A COLUMN IN A
FRAME WITHOUT RESTRAINT AGAINST SWAY

APPENDIX D
( Clause 5.2.5 )

METHOD FOR DETERMINING EFFECTIVE LENGTH

FOR STEPPED COLUMNS

D-l. SINGLE STEPPED COLUMNS

D-l.1 Effective lengths in the plane of stepping ( bending about axis x-x )
for bottom and top pa.rts for single stepped columns shall be taken as given
in Table D-l.
NOTE - The provisions of D-l.1 are applicable to intermediate columns as
well with steppings on either side, provided appropriate values of ZI and Is are
taken.

120
 TABLE D-1 EFFECTIVE LENGTH OF SINGLED STEPPED COLUMNS
( Clause D-l.1 1

SL DEOREF: OF END SKETCH EFFECTIVELENGTH COLUMN

rl0. RESTRAINT COEFFICIENTS PARAMETERS FOI
ALL CASES
(1) (2) (3) (4) (5)
-.
a) Effectively held in

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
position and restrai-
ned against rota-
tion at both ends

k,, and XII are to

be taken as per

-I+-

b) Effectively held in

ends and restrained

against rotation. at
bottom end only
where 8s I, LX
-=
k1, and III are to it TX-T
P 1
Fa;;ke; 3” per

%fectively held in _ A, to be taken as per Effective length

position and restrai- M Table D-4 of bottom part o
ned against rota- column in plant
tion at bottom end. k, = 2; c 3
of stepping
and top end held
- k,L,
ag8inst rotation
but not held in
poaition
Effective lengtl
of top part 0
I_ column in plant
of stepping=k&
d) Effectively held in
position and restrai-
II to
per Table
be taken
D-5
as

ned against rota-

tion at bottom end,
and top end neither
held against rata-
tion nor held in
position
 UPPLIED BY BOOK SUPPLY BUREAU
CENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE D-2 COEFFICIENTS OF BFFEZTIVE LENGTHS ii,, AND i& FOR COLUMNS WITH BOTH tr
”
BNDS BFFECTIVELY HELD IN POSITION AND RESTRAINED AGAINST ROTATION
( Tab& D-l )
x
A- ~ESrICDENTB 11, AND xl, POR h/r, EQUAL TO

11 * 0.1 0.2 0’3 0.4 0’5 @S-r& 0.9 1’0 1.2 1.4 I.5 1’8 -2:;

_th* (h=O)

0’05 0’74 094 1.38 1’60 1’87 2’0: 2.23 2’39 2’52 2’67 3’03 3.44 3.85 4’34 4’77
0’1 0.67 0.76 l-00 1.20 l-42 1’61 1’78 1’92 2’04 2’20 2’40 2’60 2’86 3’18 3’41
0’2 0’64 0’70 0’79 0’93 1’07 1.23 1’41 1’50 1’60 1’72 1’92 2‘11 2’28 2’45 2’64
0’3 0’62 0.68 0’74 0’85 0’95 1.06 1’18 1’28 1’39 1’48 1’67 1.82 1’96 2’12 2’20
0’4 0’60 0’66 0.71 0’78 0’87 0’99 1’07 1.16 1’26 1’34 1.50 1.65 1.79 1’94 2’08
0.5 0’59 065 0’70 0.77 0’82 0’93 0’99 1’08 1’17 1’23 199 1’53 1.66 1’79 1’92
1’0 0’55 0.60 0’65 0’70 0’75 W80 0’85 0’90 0’95 1.00 1.10 1*20 1’30 1.40 1’50
E
N Cq&8nr~~((P*~O)

0’05 0.65 0’67 0.71 b-85 1’01 1’17 1’31 1’41 1’50 1’57 1’67 1’74 1’78 1’82 1’86
O-1 0.64 0’65 0’65 0’65 0’78 0’92 1’05 1’15 1’25 1’33 1.45 1’55 1’62 1’68 1’71
0’2 0.62 0’64 0.65 0.65 0.66 0.73 0.83 0.92 1’01 1’09 1’23 1.33 1’41 1’48 1’54
09 OWI 0’63 OS4 0’65 0’66 0’67 ti73 0’81 0’89 0’94 1’09 1’20 1’28 195 1’41
0’4 0’58 0’63 0’63 0’64 0’64 0% OS8 0’75 0’82 0’88 1’01 1’10 1’19 1’26 1’32
0’5 0’57 0’61 0.63 0’64 0’64 0.65 0’68 0’72 0’77 0’83 0’94 1.04 1’12 1’19 1’25
1’0 0’55 0’58 0.60 0’61 0’62 0’63 0.65 0’67 0’70 0’73 0’80 0.88 0.93 1’01 1’05

NOTE - Intermediate value may be obtained by interpolation.

.
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE D-3 COEFFICIENTS OF EFFECTIVE LENGTHSX,, AND El, FOR COLUMXS WITH
BOTH ENDS EFFECTIVELY HELD IN POSITION AND RESTRAINED AGAINST
ROTATION AT BOTTOM END ONLY
( Tuble D-l )
COEFBICIENTSklr AND LIZBOR Lp/LI EQUAL TO
I,/Zl r------------ __~~_~~*~_-----_____-
0’1 O-2 0’3 0’4 0’5 0’6 0’7 0.8 0’9 1’0 1’2 1’4 1’6 1’8

coq$%imt I,* ( PI = 0 )

0’05 0’97 1’66 2’10 2’43 2’72 2’92 3’08 3’24 3’48 3.73 4’22 4’85 5’36 6’00 6’58
0’1 0’83 1’21 1’57 1’95 2’14 2’33 2% 2’60 2’76 2’91 3.28 3.61 4’03 4’43 4’85
0’3 0’78 0’90 1’09 1’27 1’44 1’60 1’74 1’86 1’98 2’11 2’35 2’51 2’76 2’99 3’25
‘s
w 0.5 0’78 O-86 0’99 1’10 1’22 1’35 l-47 1’57 J’67 1’76 1’96 2’15 2’34 2’50 2’76
1’0 0’78 O-85 0’92 0’99 1’06 1’13 1’20 1’27 1’34 1’41 1’54 1’68 1’82 1’97 2’10

Coe&ientI,, ( Pr = 0 )
0’05 0’67 0’67 0’82 1’16 1’35 1’48 1’58 l-65 1’69 1’74 1’81 1’84 1’86 1’88 1’90
O-1 0’67 0.67 0’73 0’93 1’11 1’25 1’36 1’45 1’52 1.57 1’66 1’72 1’77 1’80 1’82
O-3 0’67 0.67 0’67 0’71 0.80 O-90 0’99 1’08 1’15 1’22 1’33 1’41 1’48 1’54 1’59
O-5 0’67 0’67 0.67 0’69 0’73 0’81 0’87 0’94 1.01 1’07 1’17 1’26 1’33 1’39 1’44
1’0 0’67 0’67 0’67 O-68 0’71 0’74 0’78 0’82 0’87 0’91 0.99 1’07 1’13 1’19 1’24

Nom - Intermediate values may be obtained by interpolation.

::
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE D-4 COEFFICIENT OF EFFECTIVE LENGTH k; FOR COLUMNS EFFECTIVELY HELD IN
POSITION AND RESTRAINED AGAINST ROTATION AT BOTTOM END AND TOP END
HELD AGAINST ROTATION BUT NOT HELD IN POSITION
( TableD-l )
COEFFICIENT k, BOR i,/il EQUAL TO
Cl r-‘- ----~~~~~~~_~~~_*~~~~__-~~~~_~
0 0.2 0’4 0.6 0’8 1’0 1’2 1’4 1’6 1.8 2’0 2’5 5’0 10 20

0 2’0 1’86 1’76 1’67 1’60 1’55 1’50 I.46 1.43 1.40 1’37 1’32 1’18 l.iO 1’05

0’5 2’0 1’90 1’80 1’74 1’69 1’65 1’61 1’58 1’55 1’53 - - - - -

1’0 2’0 2’00 2’00 2’00 2’00 2’00 - - - - - - - - -

c
I.5 2-O 2.25 2.38 2.48 - - - - - - - _ - - _
%
2.0 2’0 2’66 2’91 - - -; - - _ - - - - _ -

2.5 2’5 3’17 3.50 - - - - _ _ _ _ - - - -

3.0 3’0 3.70 4.12 - _ - - _ _ _ _ - _ - _

NOTE - Intermediate values may be obtained by interpolation.

 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
TABLE D-5 COEFFICIENT OF EFFECTIVE LENGTH G FOR columns WITH TOP END FREE
AND BOTTOM END EFFECTIVELY HELD IN POSITION AND RESTRAINED
AGAINST ROTATION

COEFBICIENT k1 BOR ir/il EQUAL TO ?2

c, ~-_-____--_---_-_T__h--______ ---A--

I;
0 0.2 0’4 0’6 0’8 1.0 1.2 1’4 1.6 1.8 2’0 2’5 5’0 10 20
0 2’0 2’0 2’0 2’0’1 2’0 2’0 2’0 2’0 2’0 2’0 2’0 2’0 2’0 2’0 2’0
‘2 L2
0’5 2’0 2’14 2’24 2’36 2’47 2.57 2’67 2.76 2’85 294 3’02 - - - - 0
1’0 2’0 2’73 3’13 3’44 3’74 4.00 - - - - - - - - -
w
WI 1’5 3.0 3,77 4’35 4’86 - - - - - - - - - - -
2’0 4’0 4.90 5’67 _ _ - - - _ - _ _ - - -
11 LI
2.5 5.0 6.08 7.00 _ - - - _ _ _ - - - - -
3’0 6’0 7.25 _ - _ - - _ - - - - _ _ _

NOTE - Intermediate values may be obtained by interpolation. 1 P, t P2

,
rsrm-1984

D-2. EFFECTIVE LENGTH FOR DOUBLE STEPPED COLUMNS

D-2.1 Effective lengths in the plane of steppings ( bending about axis x-x )
for bottom, middle and top parts for a double stepped column shall be
taken as follows:

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
G

!ilif
13 4
L3 p2 8, L3 P
I av
L2fL-j

I2
L2 P
P( ,
1 av av
LI+Lz Ll+

Y L, 11 L, 11

I
x$%x 4 . A

Y
(a) (b) (cl (4
Coefficient kl for effective length of bottom part of double stepped
column shall be taken from the formula:

where
xl,&, & are taken from Table D-6,

t1=--,
Pl
pa
ta = pa
-
pli
La
% =--9
Ll
I’, = Average value of moment of inertia for the lower
and middle parts
I,& + Is&
=4+ Ls

126
 IS:8w-19fM

I”, = Average value of moment of inertia for middle and

top parts
IaLa + WI
- Ls + r,

Value of coefficient Ts for middle part of column is given by for-

mula

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
kl
ks E-

G
and coefficient kB for the top part of the column is given by

where

C,S G 11 ( p, + ps 1
Ll J 1, ( Pl + ps + m-

LB IlPB
c, = -
Ll d 13 ( Pl + pa + pa 1

NOTE-The provisions of D-2.1 are applicable to intermediate columns as

well with steppings on either side, provided appropriate values of Z,, Zs and 1s are
taken.

127
 LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
SUPPLIED BY BOOK SUPPLY BUREAU
As in the Original Standard, this Page is Intentionally Left Blank
 TABLE D-6 VALUES OF i;,, k; AND k;
( Cluusc D-2.1 )

DEGREE 01 END SKNTCH h COLUhtN

R~CSTRAINT PAHAMETEHS
FOR ALL CASES

a: Effectively held in & = lu 7;s= I,, lir = ilr.

where k,s is taker
position and re- where krl is taken where 1,~ is taker:
rtrained against from Table D-2 from Table D-2 from Table D-2
rotation at both
ends.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
bi Effectively
in position
held
at , %I= k‘,
where kI1 is taken
ta- tn
where in is taken where
k, = ha
1ss is taken

,
E
from Table D-3 form Table D-3
both ends from Table D-3
and restrained
against rotation
at bottom end
only.

C) Wectively held in k, = 2, 1, - L x, - ;k,

where x1 is taken
position and re- Hhrre Ik is taken #here kI is taken
‘ram Table D-4 with
.-
strained against from !‘able D-4 from Table D-4
rotation with C, = 0 with C, = 0
bottom end, ai;
top end held
against rotation
but not held in
position.

d) Xectively held in h, = 2 ;kr = 2 i, = ;tr

position and re- uhere k1 is taken
strained against rom Table D-S with
rotation ? I
- ~.A_. IT
bottom end? anad “L-L1+L, J x
top end neither
held agaiyt
rotation nor
against trans-
lation.
 LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
SUPPLIED BY BOOK SUPPLY BUREAU
As in the Original Standard, this Page is Intentionally Left Blank
 APPENDIX E
( Clause 6.2.4.1 )

LIST OF REFERENCES ON THE ELASTIC FLEXURAL

TORSIONAL BUCKLING OF STEEL BEAMS

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
Textbooks

TIMOSHENKO ( S P ) and GERE ( J M ). Theory of elastic stability.

Ed 2, 1961. McGraw-Hill, New York.
BLEICH ( F ), Buckling Strength of Metal Structures, 1952. McGraw-
Hill, New York.
JOHNSTON ( B G ), Ed. Guide to design criteria for metal compres-
sion members. Column Research Council. 1966, Ed 2. John Wiley, New
York.
GALAMBOS ( T V ). Structural members and frames. 1968. Prentice-
Hall, New Jersey

Handbook of Structural Stabi&. Column Research Committee of Japan.

197 1. @rona Publishing Co, Tokyo.

Allen ( H G ) and B&on ( P S ). Background to buckling.

Stability of structure under static and dynamic loads. American Society of

Civil Engineers, 1977 Ed.

RGfeerencesPrior to I961
LEE ( G C ), A survey of literature on the lateral instability of beams.
Welding Research Council Bulletin Series No. 63, Aug 1960.

Values of Elastic Critical Loads and Effectioe Length Factors

TRAHAIR’( N S ) . The Bending stress rules of the draft AS CA 1. J Inst.

Engrs Aust. 38; No. 6, June 1966.

TRAHAIR ( N S ). Elastic Stability of I-beam element in rigid-jointed

frames. J Inst. Engrs Aust. 38; No. 7-8 July-Aug 1966; 171.

TRAHAIR ( N S ). Elastic stability of propped cantilevers. Civ Eng

Tram, Institution of Engineers, Australia, V CE 10. No. 1; April 1968.

Safe load tables for laterally unsupported angles. Australian Institute of

Steel Construction.

131
 SUPPLIED BY BOOK SUPPLY BUREAU
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
APPENDIX F
( Clause 9.2.3.2 )

PLASTIC PROPERTIES OF INDIAN STANDARD MEDIUM

WElGHT BEAMS [ IS : 808 ( Part l )-1973 ]

DEMONA- WEICJHT SEC- L&PEE WIDTE T~cE- THICIL- Rano~ SECTION PLASTIC SE-E b D
TION TIONkt OB OR NESS NY85 GYRA- MODU- SE&ON FACTOB T- t
AHEA SEC- FLANGE OP OB MODU-
TION (4 FLAN-
TION LUS
L LUS
_$- -
(4 ‘ZP
El
(1) (2) (3) (4) (5) (6). (7) (8) (9) (10) (11) (121 (13) (14)
kg/m cm* mm mm mm mm cm cm cm3 cm5
ISMB 100 11.5 14’7 100 70 7’5 4’5 4’14 1’55 50’4 58’6 1’16 9-33 22’2
ISMB 125 13.4 17’0 125 70 8’0 5’0 5’16 1’51 71’2 81’8 1’15 8’75 25’0
ISMB 150 15 19-l 150 75 8’0 5’0 6’13 1’57 95’7 110 1’15 9’38 30’0
ISMB 175 19’5 24’9 175 85 9’0 5.8 7.13 1’76 144’3 166 1’15 9’44 30’17
ISMB 200 25’4 32’3 200 100 10’8 5.7 8.32 2’15 224 254 1’13 9’26 35’1
ISMB 225 31.2 39’7 225 110 11’8 6’5 9’31 2’34 306 348 1’14 9’32 34’6
ISMB 250 37.3 47% 250 125 12’5 6’9 10’40 2’65 410 466 1’14 10’00 36’2
ISMB 300 46-l 58.7 300 140 13-l 7.7 12’40 2’86 599 683 1’14 10’7 38’9
ISMB 350 52’4 66.7 350 140 14’2 a.1 14-30 2’84 779 890 1’14 9’86 43.2
ISMB 400 61’6 78’5 400 140 16’0 8’9 16’2 2’82 1020 1 176 1’15 8’75 44.9
ISMB 450 72’4 92’3 450 150 17.4 9’4 18’2 3’01 1350 1533 1’14 8’62 47’9
ISMB 500 86’9 111 500 180 17.2 10’2 20’2 3’52 1810 2075 1’15 10’47 49.0
ISMB 550 104 132 550 190 19’3 11’2 22’2 3.73 2360 2712 1’15 9.84 49’1
ISMB 600 123 156 600 210 20’8 12’0 24’2 4’12 3060 3511 1’15 10’10 50.0
 IS:lam-1984

APPENDIX G
( czause12.1.1 )

GENERAL RECOMMENDATIONS FOR STEELWORK

TENDERS AND CONTRACTS

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
G-O. GENERAL
G-041 The recommendations given in this Appendix are in line with those
generally adopted for steelwork construction and are meant for general
information.
G-O.2 These recommendations do not form part of the requirements of the
standard and compliance with these is not necessary for the purpose of
complying with this Code.
G-O.3 The recommendations are unsuitable for inclusion as a block
requirement in a contract, but in drawing up a contract the points men-
tioned should be given consideration.
G-l. EXCHANGE OF INFORMATION
G-161 Before the steelwork design is commenced, the building designer
should be satisfied that the planning of the building, its dimensions and
other principal factors meet the requirements of the building owner and
comply with regulations of all authorities concerned. Collaboration of
building designer and steelwork designer shouId begin at the outset of
the project by joint consideration of the planning and of such questions
as the stanchion spacing, materials to be used for the construction, and
depth of basement.
G-2. INFORMATION REQUIRED BY THE STEELWORK
DESIGNER
G-2.1 General
a) Site plans showing in plan and elevation of the proposed Iocation
and main dimensions of the building or structure;
b) Ground levels, existing and proposed;
c) Particulars of buildings or other constructions which may have to
remain on the actual site of the new building or structure during
the erection of the steelwork;
d) Particulars of adjacent buildings affecting, or affected-by, the new
work;
e) Stipulation regarding the erection sequence or time schedule;
f > Conditions affecting the position or continuity of members;

133
ISrfmJ-19g4

g) Limiti of length and weight of steel members in transit and

erection;
h) Drawings of the substructure, proposed or existing, showing:
il levels of stanchion foundations, if already determined;

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
ii) any details affecting the stanchion bases or anchor bolts;
iii) permissible bearing pressure on the foundation; and
iv) provisions for grouting ( scd 11.16 ).
In the case of._ new work, the substructure should be designed
in accordance with the relevant codes dealing with foundations
and substructure;
j) The maximum wind velocity appropriate to the site ( ste IS : 875-
1964 ); and
k) Environmental factors, such as proximity to sea coast, and corro-
sive atmosphere. Reference to bye-laws and regulations affecting
the steelwork design and construction.
012.2 Further Information Rtlatiag to Buildings

4 Plans of the floors and roof with principal dimensions, elevations

and cross sections showing heights between floor levels.
b) The occupancy of the floors and the positions of any special loads
should be given.
4 The building drawings, which should be fully dimensioned, should
preferably be to the scale of 1 to 100 and should show all stairs,
fire-escapes, lifts, etc, suspended ceilings, flues and ducts for
heating and ventilating. Doors and windows should be shown, as
the openings may be taken into account in the computation of
dead load.
Requirements should be given in respect of any maximum
depth of beams or minimum head room.
Large-scale details should be given of any special features
affecting the steelwork.

4 The inclusive weight per ms of walls, floors, roofs, suspended

ceilings, stairs and partitions, or particulars, of their construction
and finish for the computation of dead load.

The plans should indicate the floors which are to be designed

to carry partitions. Where the layout of partitions is not known,
or a given layout is liable to alteration, these facts should be
specially noted so that allowance may be made for partitions in
any position ( see IS : 875-1964 ).

134
 IS 1809-1984

e) The superimposed loads on ,the ,floors appropriate to the occu-

pancy, as given in IS : 875-1964 or as otherwise required.
f) Details of special loads from cranes, runways, tips, lifts, bunkers,
tanks, plant and equipment.
g) The grade of fire resistance appropriate to the occupancy as may
be required.

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
G-3. INFORMATION REQUIRED BY TENDERER ( IF NOT ALSO
THE DESIGNER )
G-3.1 General
a) All information listed under G-2.1;
b) Climatic conditions at site-seasonal variations of temperature,
humidity, wind velocity and direction;
c) Nature of soil. Results of the investigation of sub-soil at site of
building or structure;
d) Accessibility of site and details of power supply;
e) Whether the steelwork contractor will be required to survey the
site and set out or check the building or structure lines, founda-
tions and levels;
f) Setting-out plan of foundations, stanchions and levels of bases;
g) Cross sections and elevations of the steel structure, as necessary,
with large-scale details of special features;
h) Whether the connections are to be bolted, riveted or welded.
Particular attention should be drawn to connections of a special
nature, such as turned bolts, high strength friction grip bolts, long
rivets and overhead welds;
j) Quality of steel ( see 3 ), and provisions for identification;
k) Requirements in respect of protective paintings at works and on
site, galvanizing or cement wash;
m) Approximate dates for commencement and completion of erec-
tion;
n) Details of any tests which have to be made during the course of
erection or upon completion; and
p) Schedule of quantities. Where the tenderer is required to take
off quantities, a list should be given of the principal items to be
included in the schedule.
G-3.2 Additional Information Relating to Buildings
a) Schedule of stanchions giving sizes, lengths and typical details of
brackets, joints, etc;

535
L. ._ ..._ _ ..__.“.,_._.ll_l_l_l-l._~-_ ._. _..__. ...“.. .._- -_.._

b) Plan of grillages showing sizes, lengths and levels of grillage

beams and particulars of any stiffeners required;
c) Plans of floor beams showing sizes, lengths and levels eccentrici-
ties and end moments. The beam reactions and details of the
type of connection required should be shown on the plans;
d) Plan of roof steeldork. For a flat roof, the plan should give par-
ticulars similar to those of a floor plan. Where the roof is

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
pitched, details should be given of trusses, portals, purlins, brac-
ing, etc;
e) The steelwork drawings should preferably be to a scale of’ 1 to
100 and should give identification marks against all members;
and
f ) Particulars of holes required for services, pipes, machinery fixings,
etc. Such holes should preferably be drilled at works.
G-3.3 Information Relating to Execution of Building Work
G-3.3.1 Supply of materials.
G-3.3.2 Weight of steelwork for payment.
G4.3.3 Wastage of steel.
G-3.3.4 Insurance, freight and traniport from shop to site.
G-3.3.5 Site facilities for erection.
G-3.3.6 Tools and plants.
G-3.3.7 Mode and terms of payment.
G-3.3.8 Schedules.
G3.3.9 Forced Majewe - clauses and provisions for liquidation and
damages for delay in completion.
G-3.3.10 Escalation clauses.
G-4, DETAILING
G-4.1 In addition to the number of copies of the approved drawings or
details required under the contract, dimensioned shop drawings or details
should be submitted in duplicate to the engineer who should retain one
copy and return the other to the steel supplier or fabricators with his
comments, if any.
c-5. TIME SCHEDULE
G-5.1 As the dates on which subsequent trades can commence, depend on
the progress of erection of the steel framing, the time schedule for the
latter should be carefully drawn up and agreed to by the parties concerned
at a joint meeting.

136
 IS:SwJ-1984

G-6. PROCEDURE ON SITE

G-6.1 The steelwork contractor should be responsible for the positioning
and levelling of all steelwork. Any checking or approval of the setting out
by.the general contractor or the engineer should not relieve the steelwork

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
contractor of his responsibilities in this respect.

G-7. INSPECZTION
G-7.0 References may be made to IS : 7215-1974, c Indian Standard
tolerances for erection of steel structures ( under preparation ) ‘, and the
(Handbook for fabrication, erection and inspection of steer structures
( under preparation )’ for general guidance.
‘G-7.1 Access to Contractor’s Works - The contractor should offer
facilities for the inspection of the work at all stages.
G-7.2 Inspection of Fabrication +Unless otherwise agreed, the inspec-
tion should be carried out at the place d fabrication. The contractor
should be responsible for the accuracy of the work and for any error which
may be subsequently discovered.
G-7.3 Inspection on Site - To facilitate inspection, the contractor
should during all working hours, have a foreman or properly accredited
charge hand available on the site, together withia complete set of contract
drawings and any further drawings and instructions which may have been
issued from time to time.

G-8, MAINTENANCE
G-8.1 General - Where steelwork is to. be encased in solid concrete,
brickwork or masonry, the question of maintenance should not arise, but
where steelwork is to be housed in hollow fire protection or is to be unpro-
tected, particularly where the steeIwork is exposed to a corroding agent,
the question of painting or protective treatment of the steelwork should be
given careful consideration at the con_stn;lction stage, having regard to the
special circumstances of the case.
G-8.2 Connections - Where connections are exposed to a corroding
agent, they should be periodically inspected, and any corroded parw
should be thoroughly cleaned and painted,
G-8.2.1 Where bolted connections are not solidly encased and are sub
ject to vibratory effects of machinery or plant, they should be periodicalv
inspected and all bolts tightened.

137

^
1.
L

INDIAN STANDARDS

ON

STRUCTURAL ENGINEERING

IS:

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
800-1984 Code of practice for general construction in steel ( second rsoizioa )
Sol-1975 Code of practice for use of cold formed light gauge steel structural members
in general building construction (Jirsr rcuision ).
,802 Code of practice for use of structural steel in overhead transmission line towers:
( Part 1 )-I977 Loads and rJermissible stresses ( second revision 1
t Part 2 j-1978 Fabrication, galvanizing, inspection and packing
( Part 3 l-1978 Testing
803-1976 &de of practice for design, fabrication and erection of vertical mild steel
cylindrical welded oil storage tanks (first rcnision )
805-1968 Code of practice for use of steel in gravity water tanks
806-1968 Code of practice for use of steel tubes in general building construction
C retiscd 1
807-1968 &ode ofpractice for design, manufacture, erection and testing ( structural
portion ) of cranes and hoists (first reoision y
1915-1961 Code of practice for steel bridges ,
3177-1977 Codeof practice for design of overhead travelling cranes and gantry
_ . cranes
other than steel-works c&i& (Jirsf revision ) -
4000-1967 Code of practice for assembly of structural joints using high tensile friction
. e
grip tasreners
4014 Code of practice for steel tubular scaffoldings:
( Part 1 )-I967 Definitions and materials
( Part 2 )-1967 Safety regulations for scaffolding
4137-1967 Code of practice for heavy dut electric overhead travelling cranes inclu-
ding special service machines Por use in steel works
4573-1982 Code of practice for design of mobile crane’i ( all types ) (first r&in )
6533-1971 Code of practice for design and construction of steel chimneys
7205-1974 Safety code for erection of structural steelwork
8147-1976 Code of practice for use of aluminium alloys in structurea
8640-1977 Recommendations for dimensional paiameters for industrial buildings
9178
-_ Criteria for design of steel bins for storaee of bulk materials:
( Part l )-1979 Gen&al requirements and assesiment of loads
( Part 2 )-1979 Design criteria
( Part 3 )-1981 Bins designed for mass flow and funnel flow
9964 Recommendations for maintenance and operation of petroleum storage tanh:
(\ Part 1 1-1981 Prenaration
. of tanks for safe entry and work
( Part 2 )-1981 Inspection
%Zleisl
8041967 Rectangular pressed steel tanks (first revision )
7215-1974 Tolerances for fabrication of steel structures
8081-1976 Slotted sections
SP : 6 ISI Kandbooks for Structural Engineers
SP : 6 (I)-1964 Structural steel sections
SP : 6 (2)-1962 Steel beams and plate girders
SP : 6.(3)-1962 Steel column and struts
SP : 6 (4)-1969 Use of high strength friction grip bolts
SP : 6 (5)-1980 Structural use of light gauge steel
SP : 6 (6)-1972 Application of plastic theory in design of steel structures
SP : 6 (7).1972 Simple welded girders
 BUREAU OF INDIAN STANDARDS
Headquartera.
Manak Bhavan, 9 Bahadur Shah Zafar Marg, NEW DELHI 110002
Telephones: 323 0131,323 3375,323 9402 Fax :+ 91 011 3234062,3239399, 3239382
E -mail : bis@vsnl.com. Internet : http://wwwdel.vsnl.net.in/bis.org

Cenffal Laboratory : Telephone

Plot No. 20/9, Site IV, Sahibabad industrial Area, Sahibabad 201010 77 00 32

SUPPLIED BY BOOK SUPPLY BUREAU

Y
LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONL
Regional Offices:
Central : Manak Bhavan, 9 Bahadur Shah Zafar Marg, NEW DELHI 110002 3237617
*Eastern : l/14 CIT Scheme VII, V.I.P. Road, Kankurgachi, CALCUTTA 700054 337 86 62
Northern : SC0 335336, Sector 34-A, CHANDIGARH 160022 60 36 43
Southern : C.I.T. Campus, IV Cross Road, CHENNAI 600113 235 23 15
tWestern : Manakalaya, E.9, MIDC, Behind Marol Telephone Exchange, 832 92 95
Andheri (East), MUMBAI 400093
Branch Offices:
‘Pushpak’, Nurmohamed Shaikh Marg, Khanpur, AHMEDABAD 380001 550 !3 48
SPeenya Industrial Area, 1 st Stage, Bangalore-Tumkur Road, 839 49 55
BANGALORE 560058
Commercial-cum-Office Complex, Opp. Dushera Maidan, E=5 Arera Colony, 72 34 52
Bittan Market, BHOPAL 462016
62/63, Ganga Nagar, Unit VI, BHUBANESWAR 751001 40 36 27
Kalai Kathir Building, 670 Avinashi Road, COIMBATORE 641037 21 01 41
Plot No. 43, Sector 16 A, Mathura Road, FARIDABAD 121001 28 88 01
Savitri Complex, 116 G.T. Road, GHAZIABAD 201001 71 19 98
53/5 Ward No.29, R.G. Barua Road, 5th By-lane, GUWAHATI 781003 541137
5-8-56C, L.N. Gupta Marg, Nampally Station Road, HYDERABAD 500001 3201084
E-52, Chiiranjan Marg, C- Scheme, JAIPUR 302001 37 38 79
1171418 B, Sarvodaya Nagar, KANPUR 208005 21 68 76
Seth Bhawan, 2nd Floor, Behind Leela Cinema, Naval Kishore Road, 21 89 23
LUCKNOW 226001
NIT Building, Second floor, Gokulpat Market, NAGPUR 440010 52 51 71
Patliputra Industrial Estate, PATNA 800013 26 28 08
institution of Engineers (India) Building, 1332 Shiiaji Nagar, PUNE 411005 32 36 35
Sahajanand House’3rd Floor, Bhaktinagar Circle, 80 Feet Road, 36 85 86
FtAJKOT 360802
T.C. No. 14/l 421, University P. 0. Pafayam, THIRWA NANTHAPURAM 695034 32 21 04

*Sales Cffice is at 5 Chowringhee Approach, P.O. Princep Street, 271085

CALCUTTA 700072
tSales office is at Novelty Chambers, Grant Road, MUMBAI 400007 309 65 28
$Sales Office is at ‘F’ Block, Unity Building, Narashimaraja Square, 222 39 71
BANGALORE 560802

Dee Kay Printers, New Delhi, India

 AMENDMENT NO. 3 DECEMBER 1997
TO
IS 800 : 1984 CODE OF PRACTICE FOR GENERAL

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
CONSTRUCTION IN STEEL
(SecondRevision)

I
!
( Page 17, clause 1.4 ) -Substitute
1.4 Refetpnce
the following for the existing clause:

!
?A.1 nt fmJv&?g LAisn
A..“.“.. Ciwl.n&
w.Y..SY. plt*;n
“I..“*.. Y.“.’ “I_ ruhbh
nmwn’cinm V,Y.W.. thmunh
‘“.“‘p.
i
reference in this text, constitute provision of this standard. At the time of
4 pubkation, the editions indicated were valid. AI1 standards ate subject to
revision, and parties to agreements based on this standard are encouraged to
investigate the possibility of applying the most recent editions of the standards
indicated below:
is No. Titi.??

456 : 1973 Code of practice for plain and reinforced concrete (third
revkim )

6% : 3972 Code of practice for general engineering drawings ( second

rev&& )
786 : 1967 (Supplement) SI supplement to Indian Standard
conversion factors and conversion tables (fort revi.rion )
812 : 1957 Glossaty of terms relating to welding and cutting of
metals
813 : 1966 Scheme of symbols for welding
814 : 1991 Covered electrodes for manual metal arc welding of
carbon and carbon nranganese steel (fifilr revision)
816 :1%9 Code of practice for use of metal arc welding for general
construction in mild steel (fist revision )
817 : 1966 Code of practice for training and testing of metal arc
welders ( revised )
Amend No. 3 to IS 800 : 1984

IS No. Tide
819 : 1957 Code of practice for resistance spot welding for light
assemblies in mild steel

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
819 (Patta 1 and 2) : IS0 system of limits and tits
1993
875(Parts 1 to 5 ) : Code of practice for design loads (other than earthquake)
1987 for buildings and structures
961: 1975 Structural steel (high tensile) ( second revision )
962 : 1989 Code of practice for architectural and building dra\ivings
(second revision)
1024 : 1979 Code of practice for use of welding in bridges and
structures subject to dynamic loading (first revision )
1030 : 1989 Carbon steel castings for general engineering purposes
( fuurth revision )
1148 : 1982 Hot tolled steel rivet tots (up to 40 mm diameter) for
structural purposes (I/Ii@ revision)
1149 : 1982 High tensile steel rivet baa for structutnl putposes (third
rt!ViriWl)
1261: 1959 Code of practice for seam welding in mild steel
1278 : 1972 Filler rods and wins for gas wekting (second revi.rio~)
1323 :1982 Code of practice for oxy-acetyIene welding for stru&tnI
work in mild steel ( second revision )
_ __ -
llrW(Parts 1 to 3j : Hexagon head baits, screws and nuts of product grade C
1992
1364 (Parts 1 to 5) : Hexagon head bolts, screws and nuts of product grade A
1992 and B
1367 (Parts 1 to 18) Technical supply conditions for threaded steel fasteners
1393 : 1961 Code of practice for training and testing of oxy-acetylene
welders

2
 Aruend No. 3 to IS 800 : 1984

ISNo. Titk
1395 : 1982 Molybdenumand chromiummolybdenum vanadiumlow
alloy steel electrodes for metal arc welding (fhird
WViSiOtt)

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
l477CParts land2): code of practice for painting of ferrous metals in
l97i buildings
I Criteria for earthquake resistant design of structures
I 1893 : 1984
(fourth revision)
1929 : 1982 Hot forged steel rivets for hot closing (12 to 36 mm
i diameter)(first revision )
r Structuralsteel (ordinaryquality) (second revision )
! 1977 : 1975
; 2062 : 1992 Steel for genera1 structural purposes &r&t revision)
(supersadesIS 226 : 1975)
i 2155 : 1982 Cold forged solid steel rivets for bot closing (6 to 16 mm
diameter)CfVf revision)
3613 : 1974 Acceptance tests for wire-flux combinations for
submerged-arcwelding of stnrchml steels &iwsrrevision)
3640 : 1982 Hexagon fit bolts Cfirstrevision)
3757: 1985 High-strengthStNctUKil bolts (second revision)

4000 : 1992 High strength bolts in steel structures- Code of practice

cfusrrevision)
5369 : 1975 General requirementsfor plain washers and iock washers
( fwsr revision )
5370 : 1969 Plain washerswith outside diameter3 X inside diameter
5372 : 1975 Taperwashersfor channels @MC) (fwssitevis~n )
5374 : 1975 Taperwashers for I-beams @MB) (fwst revision )
6419 : 1971 Welding rods and bare electrodes for gas shielded arc
welding of StNCtUfSl steel

3
Amend No. 3 to IS 800 : 1984

IS No. Title
6560 : 1972 Molybdenumand chromium-molybdenumlow alloy steel
weld@ rods and base electrodes for gas shielded arc

SUPPLIED BY BOOK SUPPLY BUREAU

LICENSED TO M. S. UNIVERSITY, VADODARA, FOR INTERNAL USE AT THIS LOCATION ONLY
welding
6610 : 1972 Heavy washers for steel stNctures
6623 : 1985 High strengthstructuralnuts (fist revision )
6639 : 1972 Hexagon bolts for steel structures( to be withdrawn)
6649 : 1985 Hardened and tem_peredwashers for high strength
stNctuta1bolts mluinuts (fist tevisios, )
7205 : 1974 Safety code for erectionof structuralsteel work
7215 : 1974 Tolerances for fabricationof steel structures
7280 : 1974 Bare wire elechxles for submerged arc welding of
StNctWiiisteels
7307 (part 1) : Approval tests for welding pdurcs : Part1 Fusion
1974 welding of steel
73 10 (Part 1) : Approval tests for welders working to approved weld&
1974 procedures: Pati 1 Fusion welding of steel
73l$(Partl): Approval tests for welders when welding procedure
1974 approvalis not required: Part 1 Fusion welding of steel
8500 : 1991 StNctWll steel - Micro alloyed (medium and high
strengthqualities) (/&St revision )
95% : 1980 Recommendations for metal arc welding of carbon and
carbon manganesesteels
NOTES 1. la lieu of IS 2062 : 1992 supersedingIS 226 : 1975, replace IS 226 : 1975
by IS 2062 whcrevcrappear in the text of the standad.

2 Wherever an Indian Standard is referred in the text, the versioa indicated ia 1.4 shall be
followed.

(CED7) Printed
at Dee Kay Printers, New Delhi-110015, India