R

T h e S o u l O f C o m p u t e r T e c h n o l o g y

SL-75LIV USER MANUAL v1.0

Downloaded from www.Manualslib.com manuals search engine

 Product Model : SL-75LIV
Manual Revision : V1.0
NOTICE Release Date : July 2001

his Users Guide & Technical Reference is to help system manu-

T facturers and end-users set up and install the mainboard.

Every effort has been made to ensure that the information in this
manual is accurate. Soltek Computer Inc. is not responsible for print-
ing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek Computer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for identifi-
cation purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respec-
tive companies.

Soltek Computer Inc. provides this manual “As is “ without warranty

of any kind, either express or implied, including but not limited to the
implied warranties or conditions of merchantability or fitness for a
particular purpose. In no event shall Soltek Computer Inc. be liable
for any loss or profits, loss of business, loss of use or data, interruption of
business, or for indirect, special, incidental, or consequential damages of
any kind, even if Soltek Computer Inc. has been advised of the possibility
of such damages arising from any defect or error in this manual or product.

Copyright © 2001 Soltek Computer Inc. All Rights Reserved.

• AMD Athlon ThunderbirdTM, and DuronTM processors are trademarks of AMD Corporation.
• VIA, VT8601A APOLLO PLE133 and VT82C686B are trademarks of VIA Corporation.

Downloaded from www.Manualslib.com manuals search engine

 SOLTEK AROUND THE WORLD

SOLTEK COMPUTER INC.

Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi-Chih, Taipei-

Hsien, Taiwan, R.O.C.
Telephone : 886-2-2642-9060
Fax : 886-2-2642-9065
E-mail : sales@soltek.com.tw
Web site : http://www.soltek.com.tw

SOUL TECHNOLOGY EUROPE B.V.

Address : Hongkongstraat 55, 3047 BP Rotterdam. The Neth-

erlands
Telephone : 31-10-2457492
Fax : 31-10-2457493
E-mail : sales@soultech-europe.com
Web site : http://www.soultech-europe.com

Downloaded from www.Manualslib.com manuals search engine

 75LIV

CONTENT
CHAPTER 1 INTRODUCTION ................................................. 8
1-1 MAINBOARD SPECIFICATION .................................................. 9
1-1.1 PROCESSOR ....................................................................... 9
1-1.2 CHIPSET .............................................................................. 9
1-1.3 ADVANCED HIGH-PERFORMANCE DRAM CONTROLLER 9
1-1.4 INTEGRATED HIGH PERFORMANCE 2D/3D GRAPHICS . 9
CONTROLLER ..................................................................... 9
1-1.5 AWARD BIOS V6.0 ............................................................... 9
1-1.6 SOUND CONTROLLER ..................................................... 10
1-1.7 MULTI-I/O FUNCTION ........................................................ 10
1-1.8 POWER MANAGEMENT ................................................... 10
1-1.9 HARDWARE MONITOR ..................................................... 10
1-1.10 EXPANSION SLOTS ......................................................... 11
1-1.11 FORM FACTOR ................................................................. 11
1-1.12 OTHERS ............................................................................ 11
1-2 MOTHERBOARD LAYOUT --- 75LIV ....................................... 12
1-3 CHIPSET DIAGRAM--- 75LIV ................................................... 13

CHAPTER 2 HARDWARE SETUP ......................................... 15

2-1 CPU INSTALLATION ................................................................ 16
2-2 MEMORY INSTALLATION ........................................................ 17
2-3 HDD/FDD INSTALLATION ........................................................ 18
2-4 SWITCH SETTING FOR CPU FREQUENCY AND VOLTAGE. 20
2-4.1 Information On AMD Socket 462 Processor ....................... 20
2-4.2 CPU External Frequency Setting (By SW1) ....................... 21
2-4.3 Processor Core Voltage Select (By SW2 DIP1-DIP6) ........ 22
2-4.4 Frequency Ratio Select (By SW3 DIP1-DIP4) .................... 23
2-5 JUMPER SETTING FOR DEVICES ON BOARD ..................... 24
2-5.1 JBAT1 For Clear CMOS Data ............................................. 24

Downloaded from www.Manualslib.com manuals search engine

 2-6 CONNECTORS CONFIGURATIONS ....................................... 25
2-6.1 On Board FAN Connector (FAN1, FAN2, FAN3) ................ 25
2-6.2 WOL1 Wake On LAN .......................................................... 26
2-6.3 CD-ROM Audio Connector (CD_IN1/CD_IN2) ................... 26
2-6.4 Complex Header NJP1 ...................................................... 27
2-6.5 Chassis Panel Connector .................................................. 28
2-6.6 ATX Power Supply Connector ............................................. 29
2-6.7 PS/2 Mouse And PS/2 Keyboard ........................................ 29
2-6.8 Serial Ports ......................................................................... 30
2-6.9 USB2 Header ...................................................................... 31
2-7 IRQ DESCRIPTION .................................................................. 32

CHAPTER 3 SOFTWARE SETUP ......................................... 34

3-1 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER) ....... 35
3-2 ONBOARD VGA DRIVER INSTALLATION ............................... 38
3-2.1 Install KLE133 VGA Driver For Windows 95/98/SE ............ 38
3-2.2 Install KLE133 VGA Driver For Windows NT4.0 ................. 38
3-2.3 Install KLE133 VGA Driver For Windows ME .................... 39
3-2.4 Install KLE133 VGA Driver Windows 2000 ........................ 39
3-3 AC’97 AUDIO CODEC INSTALLATION .................................... 40

CHAPTER 4 BIOS SETUP ..................................................... 42

4-1 WHAT IS BIOS SETUP ............................................................. 43
4-2 HOW TO RUN BIOS SETUP .................................................... 43
4-3 WHAT IS CMOS ....................................................................... 43
4-4 WHAT IS POST ........................................................................ 43
4-5 BIOS UPGRADE....................................................................... 43
4-5.1 Before Upgrading BIOS ...................................................... 44
4-5.2 Upgrade Process ................................................................ 44

Downloaded from www.Manualslib.com manuals search engine

 75LIV

4-6 BIOS SETUP --- CMOS SETUP UTILITY ................................. 48

4-6.1 CMOS SETUP UTILITY ...................................................... 48
4-6.2 STANDARD CMOS SETUP ................................................ 49
4-6.3 ADVANCED BIOS FEATURES ........................................... 52
4-6.4 ADVANCED CHIPSET FEATURES .................................... 57
4-6.5 INTEGRATED PERIPHERALS ........................................... 63
4-6.6 POWER MANAGEMENT SETUP ....................................... 68
4-6.7 PNP / PCI CONFIGURATION ............................................. 75
4-6.8 SMARTDOC ANTI-BURN SHIELD ..................................... 78
4-6.9 FREQUENCY/VOLTAGE CONTROL ................................. 80
4-6.10 LOAD OPTIMIZED DEFAULTS ........................................ 82
4-6.11 SET SUPERVISOR / USER PASSWORD ........................ 83
4-6.12 SAVE & EXIT SETUP ....................................................... 84
4-6.13 EXIT WITHOUT SAVING .................................................. 84

APPENDICES ......................................................................... 86
APPENDIX-1 TECHNICAL TERMS ............................................... 87
APPENDIX-2 IDENTIFYING BIOS VERSION AND BIOS PART
NUMBER ................................................................. 88
APPENDIX-3 IDENTIFYING MAINBOARD MODEL NUMBER ..... 90

Downloaded from www.Manualslib.com manuals search engine

 ITEMLIST CHECKUP

Mainboard
Support CD
User’s Manual
Bundled Bonus Pack CD
Bundled Bonus Pack Manual
ATA66/100 IDE Cable
RS232 Cable
FDD Cable

Downloaded from www.Manualslib.com manuals search engine

 75LIV

CHAPTER 1
INTRODUCTION

• This chapter briefly introduces the characteristics of this mainboard.

It includes the information regarding the chipset, CPU types, built-in
functions and layout. Users will have more ideas about mainboards
after reading this chapter.

This chapter contains the following topics :

1-1 MAINBOARD SPECIFICATION

1-2 MAINBOARD LAYOUT
1-3 CHIPSET DIAGRAM

Downloaded from www.Manualslib.com manuals search engine

 Chapter 1 Introduction

1-1 MAINBOARD SPECIFICATION

1-1.1 PROCESSOR
• Supporting AMD AthlonTM Thunderbird processors up to 1.5GHz.
• Supporting AMD AthlonTM Duron processors up to 1.2GHz.
• Supporting processor VID (voltage ID) and FID (frequency ID) auto
detection.
• Supporting AMD AthlonTM processor with 200 and 266MHz Front Side
bus.
• Supporting AMD AthlonTM 4 processors (Palomino).

1-1.2 CHIPSET
• North Bridge VIA VT8361 (KLE-133) system controller High Performance
Athlon CPU Interface.
• South Bridge VIA VT82C686B PCI to ISA bridge.

1-1.3 ADVANCED HIGH-PERFORMANCE DRAM CONTROLLER

• Supporting PC133 and PC100 SDRAM up to 3 DIMMs.
• 64-bit data width and 3.3V DRAM interface.
• Supporting up to 768MB memory space.
• Supporting different DRAM types may be used in mixed combinations.

1-1.4 INTEGRATED HIGH PERFORMANCE 2D/3D GRAPHICS

CONTROLLER
• 64-bit Single Cycle 2D/3D Graphics Engine.
• Supporting 8 Mbytes of Frame Buffer.
• Integrated 24 bit 230MHz True Color DAC.
• Extended Screen Resolutions up to 1600x1200.
• Extended Text Mode 80 or 132 columns by 25/30/43/60 rows.
• Supporting full AGP v2.0 capability.

1-1.5 AWARD BIOS V6.0

• Plug & Play V1.0.
• Flash Memory for easy upgrade.
• BIOS writing protection.
• Year 2000 compliant.
• SMARTDOC ANTI-BURN SHIELD.
• RedStorm Overclocking Tech.

Downloaded from www.Manualslib.com manuals search engine

 75LIV

1-1.6 SOUND CONTROLLER

• SoundBlaster Pro Hardware and Direct Sound Ready AC97 Digital Audio
Controller with Codec onboard.

1-1.7 MULTI-I/O FUNCTION

• Two Ultra DMA 33/66/100 Master Mode PCI EIDE ports.
• Two UART’s for Complete Serial Ports.
• Dedicated IR connector:
-- Third serial port dedicated to IR function either through the two complete serial
ports or the third dedicated port Infrared-IrDA (HPSIR) and ASK (Amplitude Shift
Keyed) IR.
• Multi-mode parallel connector supporting:
-- Standard mode, ECP and EPP.
• Floppy Disk connector supporting:
-- Two FDDs connector with drive swap support .
• Universal Serial Bus connector supporting:
-- USB v1.1 and Intel Universal HCI v1.1 compatible.
-- 2 built-in USB connectors and one USB Header (USB2) which requires an optional
USB cable to provide 2 more optional USB ports.
• PS/2 Keyboard connector.
• PS/2 Mouse connector.

1-1.8 POWER MANAGEMENT

• ACPI 1.0 compliant (Advanced Configuration and Power Interface).
• APM V1.2 compliant (Legacy power management).
• Supporting ACPI POS mode (Power On Suspend).
• Supporting Wake On LAN (WOL) & Wake On Modem (WOM).
• Supporting real time clock (RTC) with date alarm, month alarm, and century
field.

1-1.9 HARDWARE MONITOR

• Programmable control, status, to provide monitoring and alarm for flexible
desktop management of hardware temperature (software provided in
support CD).
• 5-positive voltage.
• 2 Fan-speeds statuses monitoring.

10

Downloaded from www.Manualslib.com manuals search engine

 Chapter 1 Introduction

1-1.10 EXPANSION SLOTS

• Three PCI bus Master slots.
• One ISA slot.
• Three DIMM slots.

1-1.11 FORM FACTOR

• ATX form factor 4-layer PCB.
• Mainboard size: 24.5cm x 21.0cm.

1-1.12 OTHERS
• Clock generator supporting 1 MHz linear clock setting.

11

Downloaded from www.Manualslib.com manuals search engine

 75LIV

1-2 MOTHERBOARD LAYOUT --- 75LIV

• Default Setting: 100MHz CPU External clock.

1 3 FAN1
SW1

DIP

1 2 3 4 5
upper

lower
MOUSE

PS/2
PS/2

ON
K/B

Clock
lower
upper

Generator

FDD1
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

SOCKET 462
1 2 3 4 5 6
DIP
COM1

SW2
ON
DIP

1 2 3 4 5

SW3
LPT1
ON

IDE1
IDE2
VGA

10

1
COM2
1
LINE

ATX POWER
OUT

VIA
LINE

VT8361
IN

1
MIC

FAN2
4 CD_IN1
4 CD_IN2

1
Li
PCI 1

JBAT1

3
Battery

1
1
1

AC'97
Codec

3
FAN3
1 3 PCI 2
1
WOL1
FLASH BIOS

30
15
G_LED
VIA
PWR

VT82C
PCI 3 686B
-

16
PLED

1
+
IR

USB2
SAPK RST

ISA
HDD/LED
+ - - +
NJP1

16
1

Using non-compliant memory with higher bus clock (over-clocking) may

severely compromise the reliability of system.

12

Downloaded from www.Manualslib.com manuals search engine

 Chapter 1 Introduction

1-3 CHIPSET DIAGRAM--- 75LIV

• The KLE-133 / VT82C686B chipset is a high performance, cost-effective
and energy efficient system controller for the implementation of AGP / PCI
/ ISA desktop personal computer system based on 64-bit Socket-A (AMD
Athlon) processors.

SYSCLK, SYSCLK#
Athlon INTR, NMI, SMI#, STPCLK#,
Host CPU IGNNE#, FERR#, A20M#,
PWROK, INIT#, RESET#

PROCRDY

CFWDRST
CONNECT
Address Data
Out
In
CKE
Memory Bus SDRAM
KLE133 MCLK
Clock
Monitor
VT8361 Buffer

HCLK
PCKRUN#
North Bridge
PCLK
552 BGA
PCLK PCI Bus SUSCLK,
SUSST1#

BIOS ROM

ATA 33/66/100 CPUSTP#

USB Ports 0 - 3
VT82C PCISTP#
Clock
Generator

AC97 Audio Codec AC97 Link

686B SMBus
Power Plane & Peripheral Control
GPIO and ACPI Events
Hardware Monitoring Inputs
ISA Keyboard / PS2 Mouse
Serial Ports 1 and 2
Parallel Port
South Bridge Floppy Drive Interface
352 BGA MIDI / Game Ports
RTC Crystal

Diagram of KLE133 System Block with VT82C686B South Bridge

13

Downloaded from www.Manualslib.com manuals search engine

 75LIV

MEMO
MEMO

14

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

CHAPTER 2
HARDWARE SETUP

ATTENTION !!!

1. Please refer to your processor installation or other

documentation attached to your CPU for more detailed
installing instruction.
2. Installing a heat sink and cooling fan is necessary for
proper heat dissipation from your CPU. Incorrect
installation may result in overheating and damage of
your CPU.
3. Before changing the setting of CPU Vcore from BIOS
program, user SHOULD make sure of correct speci-
fication both of CPU CLOCK and RATIO. Incorrect
setting may cause damage to your CPU.

This chapter contains the following topics :

2-1 CPU INSTALLATION

2-2 MEMORY INSTALLATION
2-3 HDD/FDD INSTALLATION
2-4 SWITCH SETTING FOR CPU FREQUENCY
AND VOLTAGE
2-5 JUMPER SETTING FOR DEVICES ON BOARD
2-6 CONNECTORS CONFIGURATION
2-7 IRQ DESCRIPTION

15

Downloaded from www.Manualslib.com manuals search engine

 75LIV

2-1 CPU INSTALLATION

WARNING !!!
• Make sure that +5V DCV and +3.3 DCV capabilities of your power supply
are suitable for the processor.
• Any attempt to operate the AMD Athlon or Duron processor without
a suitable cooling Fan will damage processor and other component.

Pull out the lever from the

1 socket, and then raise the
lever up to a 90-degree angle.
4 62
ET
CK
SO

Take notice of the red circles

AMD
2 as shown here. While insert-
ing the CPU into the socket,
you can find out there is a
definite pin orientation for
CPU and socket.
T 462
C KE
SO

Make sure that the CPU is

3 placed into the socket tightly.
Then lower down the lever
D
M
A

to complete the CPU insta-

llation.
4 62
ET
CK
SO

16

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

2-2 MEMORY INSTALLATION

WARNING!!!
• Make sure to unplug your power supply before adding or removing memory
modules or other system components. Failure to do so may cause severe
damage to both your mainboard and expansion cards.
• Be careful when inserting or removing DIMM. Forcing a DIMM in or out
of a socket improperly may damage the memory module or the socket.
Some DIMMs which contain EDO or FPM DRAM are incompliant with
the mainboard. The M/B supports 3.3V true SDRAM DIMMs only.

Installing DIMM
• Make sure you have the correct memory module type for your mainboard.
• Insert the module(s) as shown below, DIMMs have 168-pins and two
notches that will be matched by the onboard DIMM socket. Memory
modules are installed by inserting them straight into the slot until they
“click” in the right place. They only fit in one direction, so do not force
them in by a wrong direction.

168-Pin DIMM Notch Key Definitions(3.3V)

DRAM Key Position Voltage Key Position

Unbuffered 3.3V

Removing DIMM
• Press down the holding clips on both sides of a DIMM socket and the
module will be released from it.

17

Downloaded from www.Manualslib.com manuals search engine

 75LIV

2-3 HDD/FDD INSTALLATION

• To install HDD (Hard Disk Drive), you may connect the cable’s blue connector to
the mainboard’s primary (IDE1) or secondary (IDE2) connector, and then
connect the gray connector to your slave device and the black connector
to your master device. If you install two hard disks, you must configure the
second drive to Slave mode by setting its jumper accordingly. Please
refer to your hard disk documentation for the jumper settings.
1 3 FAN1
SW1

DIP

1 2 3 4 5
upper

lower
MOUSE

PS/2
PS/2

ON
K/B

Clock
lower
upper

Generator

FDD1
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

SOCKET 462
1 2 3 4 5 6
DIP
COM1

SW2
ON
DIP

1 2 3 4 5

SW3
LPT1
ON

IDE1
IDE2
VGA

10

1
COM2
1
LINE

ATX POWER
OUT

VIA
LINE

VT8361
IN

1
MIC

FAN2
4 CD_IN1
4 CD_IN2

Li
PCI 1
JBAT1

Battery
1
1
1

AC'97
Codec
3
FAN3

1 3 PCI 2
Hard Disk Drive Connector:
1

WOL1
FLASH BIOS

30
15
G_LED

VIA
Orient the red line on the
PWR

VT82C
PCI 3 686B
-

16
PLED

1
IDE ribbon cable to Pin1.
+
IR

USB2
SAPK RST

ISA
HDD/LED
+ - - +
NJP1

16
1

Gray connector

Black connector

red line
Blue connector

IDE Cable

18

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

• To install FDD (Floppy Disk Drive), you may connect the end with single
connector to the board , and connect the other end with two plugs to the
floppy drives.
1 3 FAN1
SW1

DIP

1 2 3 4 5
upper

lower
MOUSE

PS/2
PS/2

ON
K/B

Clock
lower
upper

Generator

FDD1
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

SOCKET 462
1 2 3 4 5 6
DIP
COM1

SW2
ON
DIP

1 2 3 4 5

SW3
LPT1
ON

IDE1
IDE2
VGA

10

1
COM2
1
LINE

ATX POWER
OUT

VIA
LINE

VT8361
IN

1
MIC

FAN2
4 CD_IN1
4 CD_IN2

1
Li
PCI 1
Floppy Disk Drive Connector:
JBAT1

3
Battery
1
1
1

AC'97
Codec
3

Orient the red line on the

FAN3

1 3 PCI 2
1

WOL1
FLASH BIOS

30
15
G_LED

VIA floppy ribbon cable to Pin1.

PWR

VT82C
PCI 3 686B
-

16
PLED

1
+
IR

USB2
SAPK RST

ISA
HDD/LED
+ - - +
NJP1

16
1

To 2nd Floppy Drive

red line
To mainboard
To 1st Floppy Drive

FDD Cable

19

Downloaded from www.Manualslib.com manuals search engine

 75LIV

2-4 SWITCH SETTING FOR CPU FREQUENCY AND VOLTAGE

2-4.1 Information On AMD Socket 462 Processor
• On the AMD Socket 462 Processor, you can find a codified identification
marking which is to provide useful information about the CPU. The
marking is interpreted as below:

AMD

XXXXXXXXXXX
XXXXXXXXXXXX
XXXXXXX
XXXXXXXXX
XXXXXXXXXXX
XXXX

AMD XXXX
A 0850 A P T 3 B Family/Architecture:
1 2 3 4 5 6 7 1 A= AMD Athlon™Model 4 Processor Architure.
D= AMD Duron™Processor Architecture.

Speed: 0850= 850MHz, 0900= 900MHz,

2
1000= 1000MHz, 1100= 1100MHz, etc.

3 Package Type: M= Card Module, A= PGA.

4 Operating Voltage: S= 1.5V, U= 1.6V, P= 1.7V, M= 1.75V, N= 1.8V.

Case Temperature: Q= 60 C, X= 65 C, R= 70 C, Y= 75 C,
0 0 0 0

5
T= 90 C, S=95 C.
0 0

6 Size of L2 Cache: 1= 64Kbyte, 2= 128Kbyte, 3= 256Kbyte.

7 Max FSB: A= B= 200MHz, C or others= 266MHz. (For correct

FSB setting, please refer to next chapter)

20

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

2-4.2 CPU External Frequency Setting (By SW1)

CPU EXTERNAL PCI FSB
SW1 FREQUENCY FREQUENCY FREQUENCY

DIP

1 2 3 4 5
100MHz
ON
DIP (Default) 33.3MHz 200MHz

1 2 3 4 5

103MHz 34.3MHz 206MHz

ON
DIP

1 2 3 4 5

105MHz 35.0MHz 210MHz

ON
DIP

1 2 3 4 5

110MHz 36.7MHz 220MHz

ON
DIP

1 2 3 4 5

112MHz 37.3MHz 224MHz

ON
DIP

1 2 3 4 5

115MHz 38.3MHz 230MHz

ON
DIP

1 2 3 4 5

120MHz 40.0MHz 240MHz

ON
DIP

1 2 3 4 5

124MHz 31.0MHz 248MHz

ON
DIP

1 2 3 4 5

133.3MHz 33.3MHz 266MHz

ON
DIP

1 2 3 4 5

140MHz 35.0MHz 280MHz

ON
DIP

1 2 3 4 5

150MHz 37.5MHz 300MHz

ON

IMPORTANT:
• You may figure out the correct processor type by processor’s OPN
(Ordering Part Numbers). Correct CPU external frequency is key to ensure
reliability of your system.
• Incorrect CPU external frequency or overclocking might cause unstable
performance, so we strongly recommend to leave “SW1” at default setting
or legal operation.

21

Downloaded from www.Manualslib.com manuals search engine

 75LIV

2-4.3 Processor Core Voltage Select (By SW2 DIP1-DIP6)

• DIP1-DIP6 SW2 allow you to adjust processor core voltage manually.
We recommend to leave SW2 DIP1 at default, the default means the
correct processor core voltage is generated according to VID of CPU.

DIP SW2 DIP2 ~ DIP6 SETTING SW2 DIP1

DIP

DIP
1 2 3 4 5 6

1 2 3 4 5 6

1 2 3 4 5 6
0.0v 1.100v 1.125v
(Default)
ON

ON

ON
DIP

DIP
DIP
1 2 3 4 5 6

1 2 3 4 5 6
1 2 3 4 5 6
1.150v 1.175v 1.200v
ON

ON
ON
Auto
DIP

DIP
DIP

1 2 3 4 5 6

1 2 3 4 5 6
1 2 3 4 5 6

(Default)
1.225v 1.250v 1.275v
ON

ON
ON

DIP

1 2 3 4 5 6
DIP
DIP

DIP

ON
1 2 3 4 5 6
1 2 3 4 5 6

1 2 3 4 5 6
1.300v 1.325v 1.350v
ON
ON

ON
DIP
DIP

DIP
1 2 3 4 5 6
1 2 3 4 5 6

1 2 3 4 5 6
1.375v 1.400v 1.425v
ON
ON

ON

By DIP 2-6

DIP

1 2 3 4 5 6
DIP
DIP

DIP

1 2 3 4 5 6
1 2 3 4 5 6

1 2 3 4 5 6

ON
1.450v 1.475v 1.500v
ON
ON

ON
DIP

DIP
DIP

1 2 3 4 5 6

1 2 3 4 5 6
1 2 3 4 5 6

1.525v 1.550v 1.575v

ON

ON
ON

SW2 DIP 1 allows

DIP
DIP

DIP

1 2 3 4 5 6
1 2 3 4 5 6

1 2 3 4 5 6

you to enable or
1.600v 1.625v 1.650v disable
ON
ON

ON

"Processor Core
Voltage Select"
function.
DIP

DIP
DIP
1 2 3 4 5 6

1 2 3 4 5 6
1 2 3 4 5 6

1.675v 1.700v 1.725v

ON

ON
ON

DIP
DIP
DIP

1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6

1.750v 1.775v 1.800v

ON
ON
ON
DIP

DIP
1 2 3 4 5 6

1 2 3 4 5 6

1.825v 1.850v
ON

ON

22

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

2-4.4 Frequency Ratio Select (By SW3 DIP1-DIP4)

• The AMD Athlon and Duron processors provides four Frequency ID signals
(DIP1-DIP4) (FID) for the system controller to indicate the SYSTCLK
multiplier at which the processor core operates. Normally, multiplier (or bus
ratio) is detected automatically. Therefore, if the processor does not support
the function, then “Bus Ratio” can not be selected.
• When DIP5 of SW3 is on, LED “LED1” will be on, and light is on, it means
that Bus Ratio Select Function is enabled. So as long as your CPU supports
Bus Ratio Select function, then Bus Ratio can be selected by users.
1 3 FAN1
SW1

DIP

1 2 3 4 5
upper

lower
MOUSE

PS/2
PS/2

ON
K/B
Clock

lower
upper
Generator

FDD1
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

LED1
SOCKET 462

1 2 3 4 5 6
DIP
COM1

SW2
ON
DIP

1 2 3 4 5

SW3
LPT1
ON
NOTICE : Setting of multiplier

IDE1
IDE2
VGA

10

1
COM2
12.5x or above will depend on

1
the type of CPU on board . LINE

ATX POWER
OUT
VIA
LINE

VT8361
IN

1
MIC

FAN2
_IN1
_IN2

SW3 DIP1 ~ DIP4 SETTING SW3 DIP5

DIP

DIP
1 2 3 4 5

1 2 3 4 5

5.5x 6.0x
(Default)
ON

ON

Bus ratio detected

by FID (Auto)
DIP

DIP
1 2 3 4 5

1 2 3 4 5

DIP

6.5x 7.0x
1 2 3 4 5
ON

ON

ON
DIP

DIP
1 2 3 4 5

1 2 3 4 5

7.5x 8.0x
ON

ON

Bus ratio selected

by SW1 DIP 1-4
DIP

DIP
1 2 3 4 5

1 2 3 4 5

DIP

1 2 3 4 5

8.5x 9.0x
ON

ON

ON
DIP

DIP
1 2 3 4 5

1 2 3 4 5

9.5x 10.0x
ON

ON

SW1 DIP 5 allows

DIP

DIP
1 2 3 4 5

1 2 3 4 5

you to enable or
10.5x 11.0x
disable the
ON

ON

"Frequency Ratio
Select" function.
DIP

DIP
1 2 3 4 5

1 2 3 4 5

11.5x 12.0x
ON

ON

*
DIP

DIP
1 2 3 4 5

1 2 3 4 5

12.5x
or 14.0x
13.0x
ON

ON

* Setting of Multiplier 12.5x or above will depend on the type of CPU on

board.

23

Downloaded from www.Manualslib.com manuals search engine

 75LIV

2-5 JUMPER SETTING FOR DEVICES ON BOARD

• The following diagrams show the locations of jumper blocks on the
mainboard.

CAUTION
• Do not remove the jumper when power is on. Always make sure the power
is off before changing any jumpers. Otherwise, mainboard could be
damaged..
• All jumper pins covered with black marks are closed pins.

2-5.1 JBAT1 For Clear CMOS Data

A battery should be used to supply the power for the CMOS RAM to retain
the mainboard configuration.
1 3 FAN1
SW1
DIP

1 2 3 4 5
upper

lower
MOUSE

PS/2
PS/2

ON
K/B

Clock
lower
upper

Generator
FDD1
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

SOCKET 462
1 2 3 4 5 6
DIP
COM1

SW2
ON
DIP

1 2 3 4 5

SW3
LPT1
ON

IDE1
IDE2
VGA

10

JBAT1 For Clear CMOS Data:

COM2
1
LINE

ATX POWER
OUT

VIA
3
LINE

VT8361
IN

Clear CMOS Data

1
MIC

FAN2
4 CD_IN1
4 CD_IN2

JBAT1
3

1
1

Li
PCI 1
JBAT1

Battery
1
1
1

AC'97
3
Retain Data
Codec
3
FAN3

1 3 PCI 2
1

WOL1
FLASH BIOS

(default)
30
15
G_LED

VIA
1 JBAT1
PWR

VT82C
PCI 3 686B
-

16
PLED

1
+
IR

USB2
SAPK RST

ISA
HDD/LED
+ - - +
NJP1

16
1

NOTE: You can clear CMOS by 2-3 pin closed when the system is POWER
OFF. Then, return to 1-2 pin closed position (default). You may damage
the mainboard if clearing the CMOS with POWER ON. Unplugging the
power cord from power supply before clearing CMOS will be a safest bet
for user.

24

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

2-6 CONNECTORS CONFIGURATIONS

• This section lists out all connectors configurations for users’ reference.

2-6.1 On Board FAN Connector (FAN1, FAN2, FAN3)

1 3 FAN1
SW1

DIP

1 2 3 4 5
upper

lower
MOUSE

PS/2
PS/2

ON
K/B

Clock

On Board FAN Connector

lower
upper

Generator

FDD1
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

SOCKET 462 (FAN1):

1 2 3 4 5 6
DIP
COM1

SW2
ON
DIP

1 2 3 4 5

SW3

On Board FAN Connector

LPT1
ON

IDE1
IDE2

(FAN2):
VGA

10

1
COM2
1

On Board FAN Connector

LINE

ATX POWER
OUT

VIA
LINE

VT8361
(FAN3):
IN

1
MIC

FAN2
4 CD_IN1
4 CD_IN2

Li
PCI 1
JBAT1

Battery
1
1
1

AC'97
Codec

CPU FAN
3
FAN3

1 3 PCI 2 FAN1
1

WOL1
FLASH BIOS

30
15
G_LED

VIA
PWR

VT82C
PCI 3 686B
-

16
PLED

SYSTEM FAN
1
+
IR

USB2
FAN2
SAPK RST

ISA
HDD/LED
+ - - +
NJP1

16
1

CHASSIS FAN FAN3

GND
+12V
SENSOR

These fan connectors support CPU/System chassis cooling fan with +12V.
When connecting wire to FAN connectors, users should pay attention that
the red wire is for the positive current and should be connected to pin +12V,
and the black wire is Ground and should be connected to pin GND. If your
mainboard has Hardware Monitor chipset on-board, you must use a specially
designed fan with speed sensor to take advantage of this function.
For fans with speed sensors, each rotation of the fan blades will send out 2
electric pulses, by which System Hardware Monitor will work out the fan
rotation speed by counting the pulses.

NOTE 1: Always consult vendor for proper CPU cooling fan.

NOTE 2: CPU FAN is supported by Hardware Monitor, with which a
warning will be given out against high CPU temperature.

25

Downloaded from www.Manualslib.com manuals search engine

 75LIV

2-6.2 WOL1 Wake On LAN

1 3 FAN1
SW1

DIP

1 2 3 4 5
upper

lower
MOUSE

PS/2
PS/2

ON
K/B Clock
lower
upper

Generator

FDD1
+5V standby
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

SOCKET 462
GND
1 2 3 4 5 6
DIP
COM1

SW2
ON

PME
DIP

1 2 3 4 5

SW3
LPT1
ON

IDE1
IDE2
VGA

10

1
COM2
1
LINE

ATX POWER
OUT

VIA Wake On LAN:

LINE

VT8361
IN

1
MIC

FAN2
4 CD_IN1
4 CD_IN2

Connect the Wake On

1
Li
PCI 1

JBAT1
LAN signal from LAN

3
Battery

1
1
1

AC'97
Codec

3
WOL1
FAN3
1 3 PCI 2
card to WOL1
1
WOL1
FLASH BIOS

30
15
G_LED
VIA PWR

VT82C
PCI 3 686B -
16 PLED
1
+
IR

USB2
SAPK RST

ISA
HDD/LED
+ - - +
NJP1

16
1

This connector is connected to the LAN card with a Wake On LAN output.
The connector powers up the system when it receives a wake-up packet or
signal through the LAN card.

This feature requires that Wake On LAN feature is enabled in the “Power
Management Setup” of BIOS setting and that your system must be on an
ATX power supply with at least 720mA / +5V standby power.

2-6.3 CD-ROM Audio Connector (CD_IN1/CD_IN2)

1 3 FAN1
SW1
DIP

1 2 3 4 5
upper

lower
MOUSE

PS/2
PS/2

ON
K/B

Clock
lower
upper

Generator
FDD1
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

SOCKET 462
1 2 3 4 5 6
DIP
COM1

SW2

1 4 CD_IN1
ON
DIP

1 2 3 4 5

SW3
LPT1
ON

1 4 CD_IN2
IDE1
IDE2
VGA

10

1
COM2
1
LINE

ATX POWER
OUT

VIA CD-ROM Audio Connector:

LINE

VT8361
IN

1
MIC

FAN2
PIN NO. CD_IN1 CD_IN2
4 CD_IN1
4 CD_IN2

Li
PCI 1
PIN 1 Left Channel Left Channel
JBAT1

Battery
1
1
1

AC'97
Codec
3
FAN3

1 3 PCI 2 PIN 2 GND GND

1

WOL1
FLASH BIOS

30
15
G_LED

VIA
PIN 3 GND Right Channel
PWR

VT82C
PCI 3 686B
-

16
PLED

1
+
IR

USB2
PIN 4 Right Channel GND
SAPK RST

ISA
HDD/LED
+ - - +
NJP1

16
1

26

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

2-6.4 Complex Header NJP1

• This complex Header consists of 8 connectors providing various supports:

NJP1
30
NO CONNECTION GND
NO CONNECTION SUSPEND LED 4
NO CONNECTION SUSPEND LED SIGNAL
Vcc
1 POWER SWITCH
ATX POWER SWITCH NO CONNECTION
NO CONNECTION
NO CONNECTION
Vcc GND (-)
NO CONNECTION NO CONNECTION POWER LED 5
2 INFRARED(IR) INFRARED TRANSMIT SIGNAL Vcc (+)
GND
INFRARED TRANSMIT SIGNAL GND
RESET SWITCH 6
RESET SIGNAL

3 2nd HDD LED

Logic High(+) Vcc
HDD LED SIGNAL (-) GND
SPEAKER 7
HDD LED SIGNAL (-) NO CONNECTION
3 1st HDD LED
Logic High (+) SPEAKER SIGNAL
1

1. Power Switch Connector:

CONNECTION: Connected to a momentary button or switch.
FUNCTION: Manually switching the system between “On” and “Soft Off”.
Pressing the momentary button for more than 4 seconds
will also turn the system off.

2. IR Connector (Infrared Connector):

CONNECTION: Connected to Connector IR on board.
FUNCTION: Supporting wireless transmitting and receiving module on
board.

3. 1st HDD LED Connector / J2 2nd HDD LED Connector:

CONNECTION: Connected to HDD LED.
FUNCTION: To supply power to HDD LED.

4. Suspend LED Connector:

CONNECTION: Connected to Suspend indicator.
FUNCTION: To supply power to “Suspend indicator”.

5. Power LED Connector:

CONNECTION: Connected to System Power LED.
FUNCTION: To supply power to “System Power LED”.

27

Downloaded from www.Manualslib.com manuals search engine

 75LIV

6. Reset Switch Connector:

CONNECTION: Connected to the case-mounted “Reset Switch”.
FUNCTION: To supply power to “Reset Switch” and support system
reboot function.

7. Speaker Connector:
CONNECTION: Connected to the case-mounted Speaker.
FUNCTION: To supply power to the case-mounted Speaker.

2-6.5 Chassis Panel Connector

A. B. C. D.

E. F. G. H. I. J. K.

A : PS/2 MOUSE PORT

B : USB 0 PORT
C : LPT1 PORT
D : GAME/MIDI PORT
E : PS/2 KEYBOARD PORT
F : USB 1 PORT
G : COM 1 PORT
H : VGA PORT
I : LINE OUT / SPEAKER OUT PORT
J : LINE IN
K : MICROPHONE

28

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

2-6.6 ATX Power Supply Connector

• This connector connects to an ATX power supply. The plug from the power
supply should only be inserted to ATX Power connector in a specific
orientation. Find the proper orientation and push it down firmly to make
sure that all pins are aligned.
• Your power supply should support at least 10mA on the 5V standby voltage.
It may cause difficulty to turn on the system power if the power supply
does not support the load.
• For Wake On LAN function, the power supply should support at least
720mA current.

+12V VCC
+5V Standby VCC
Power Good -5V
GND GND
VCC GND
GND GND
VCC Power Supply on
GND GND
VCC3 -12V
VCC3 VCC3

2-6.7 PS/2 Mouse And PS/2 Keyboard

PIN 6 : None PIN 6 : None

PIN 5 : Mouse Clock PIN 5 : Keyboard Clock
PIN 4 : Vcc PIN 4 : Vcc
PIN 3 : GND PIN 3 : GND
PIN 2 : None PIN 2 : None
PIN 1 : Mouse Data PIN 1 : Keyboard Data

PS/2 MOUSE PS/2 KEYBOARD

29

Downloaded from www.Manualslib.com manuals search engine

 75LIV

2-6.8 Serial Ports

• One serial port COM 1 is ready for a mouse or other serial devices. A
second serial port is available in the form of a 9-pin Header (COM2) to
provide connection to a second serial device by an RS232 cable.
1 3 FAN1
SW1

DIP

1 2 3 4 5
upper

lower
MOUSE

COM 2 Header
PS/2
PS/2

ON
K/B

Clock
lower
upper

Generator

FDD1
USB0
USB1

DIMM1
DIMM2
DIMM3
LED1

SOCKET 462
1 2 3 4 5 6
DIP
COM1

SW2
ON
DIP

1 2 3 4 5

SW3
LPT1
ON

IDE1
IDE2
VGA

10

1
COM2

PIN1
1
LINE

ATX POWER
OUT

VIA
LINE

VT8361
IN

COM 2 Header:
1
MIC

FAN2
4 CD_IN1
4 CD_IN2

Orient the red markings on the

1

Li
PCI 1
floppy ribbon cable to PIN1.
JBAT1

Battery
1
1
1

AC'97
Codec
3
FAN3

1 3 PCI 2
1

WOL1
FLASH BIOS

30
15
G_LED

VIA
PWR

VT82C
PCI 3 686B
-

16
PLED

1
+
IR

USB2
SAPK RST

ISA
HDD/LED
+ - - +
NJP1

16
1

RS232 cable

30

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

2-6.9 USB2 Header

• This header is for connecting the additional USB cable to provide you two
additional USB ports. User can order the additional USB cable from your
mainboard dealer and vender.

Additional USB Cable (Optional)

red wire
GND GND
Black Black

16
1 1
Red Green Red Green
VCC DO+ VCC DO+

White Black White Black

DO- GND DO- GND 16
1
USB2 Header USB 2 Header
• When plugging the USB cable into USB2 Header, users must make sure
the red wire is connected to the first pin.

31

Downloaded from www.Manualslib.com manuals search engine

 75LIV

2-7 IRQ DESCRIPTION

IRQRR Function DescriptionR Priority

IRQP 0P System TimerPP 1
IRQP 1P Keyboard ControllerP 2P
IRQP 2P Programmable InterruptP N/A
IRQP 3P Serial Port (COM 2)P 11
IRQP 4P Serial Port (COM 1)P 12
IRQP 5PP 13P
IRQP 6P Floppy Disk ControllerP 14
IRQP 7P Parallel Port (LPT1)P 15
IRQP 8P Real Time Clock (RTC)P 3
IRQP 9PP 4
IRQP 10PP 5P
IRQP 11PP 6P
IRQP 12P PS/2 Mouse PortP 7
IRQP 13P CoprocessorP 8
IRQP 14P Primary IDE ChannelP 9
IRQP 15P Secondary IDE ChannelP 10

• Both ISA and PCI expansion cards may require IRQs. System IRQs are
available to cards installed in the ISA expansion bus first, then any
remaining IRQs are available to PCI cards. Currently, there are two types
of ISA cards.
• The original ISA expansion card design, now referred to as “Legacy” ISA
card, requires you to configure the card’s jumpers manually and then install
it in any available slot on the ISA bus. To see a map of your used and free
IRQs in Windows 98, the Control Panel in My Computer, contains a
System icon, which gives you a Device Manager tab. Double-Clicking on a
specific hardware device gives you a Resources tab which shows the
Interrupt number and address. Double-Clicking Computers to see all the
interrupts and addresses for your system. Make sure that each ISA device
should be assigned to one IRQ respectively. If ISA device share IRQ with
any other device, your computer will easily get into trouble.

32

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 Hardware Setup

MEMO
MEMO

33

Downloaded from www.Manualslib.com manuals search engine

 75LIV

CHAPTER 3
SOFTWARE SETUP

ABOUT SUPPORT CD

• In Support CD, it contains most informations for user’s requirement, such

as Acrobat Reader, BIOS, User’s full version Manual, Driver, Hardware
Monitor (if mainboard supports this function), Patch, and Utilities etc. User
can browse the CD and get further details in regard of our mainboard. Of
course, welcome to vendor’s website for the newest release.

This chapter contains the following topics :

3-1 VIA CHIPSET DRIVER INSTALLATION (4-IN-1

DRIVER)
3-2 ONBOARD VGA DRIVER INSTALLATION
3-3 AC’97 DRIVER INSTALLATION

34

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 Software Setup

3-1 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER)

• Please put the Support CD • When a welcome window
1 provided in your mainboard 2 appears on the screen,
package into the CD-ROM users should choose “Install
drive. Driver”.

• Click on the “VIA Chipset • Click on the “4-in-1 driver”.

3 Driver”. 4

• Click on the “Install via 4-in-1 driver” to continue.

5

Next • Press “Next” button to

6 continue.

Yes
• Click “Yes” to continue.
7

35

Downloaded from www.Manualslib.com manuals search engine

 75LIV

• Press select the checkbox

8 as below:

Bus Master PCI IDE

Driver
AGP VxD Driver
VIA Chipset Function’s
Registry
IRQ Routing Miniport
Driver
Next

Note: For user who is upgrading VIA Drivers, we recommend to install the
4-in-1 as it will automatically detect and update the necessary drivers.

• Select “Install VIA ATAPI

Next
9 Vendor Support Driver”
checkbox, then click the
“Next” button to continue.

• Click on “Click to enable

10 DMA Mode” checkbox to
Next enable DMA function, then
click the “Next” button to
continue.

36

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 Software Setup

Next • Select “Install VIA AGP Vx

11 D” in turbo mode and press
Next button to continue.

• Select “Install VIA IRQ

Next 12 Routing Miniport Driver”
checkbox, then click the
“Next” button to continue.

• After all these setup pro-

Finish 13 cedures have finished, lease
restart your computer by
clicking on Finish.

37

Downloaded from www.Manualslib.com manuals search engine

 75LIV

3-2 ONBOARD VGA DRIVER INSTALLATION

• We provide a simple process for user to install VGA driver. Whichever
Microsoft Windows operating system user adopts, they have similar
installation below.

3-2.1 Install KLE133 VGA Driver For Windows 95/98/SE

• Please put the Support CD • When a welcome window
1 provided in your mainboard 2 appears on the screen,
package into the CD-ROM users should choose “Install
drive. Driver”.

• Click on the “VIA chipsets • Click on the “VIA KLE133

3 Driver”. 4 VGA Driver” to continue.

• Click on the “Install VGA • Follow the instruction on

5 Driver for Win95/98/SE”. 6 screen to complete the
installation, after which
please restart your PC.

3-2.2 Install KLE133 VGA Driver For Windows NT4.0

• Please put the Support CD • When a welcome window
1 provided in your mainboard 2 appears on the screen,
package into the CD-ROM users should choose “Install
drive. Driver”.

• Click on the “VIA chipsets • Click on the “VIA KLE133

3 Driver”.
4 VGA Driver” to continue.

• Click on the “Install VGA • Follow the instruction on

5 Driver for NT4.0”. 6 screen to complete the
installation, after which
please restart your PC.

38

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 Software Setup

3-2.3 Install KLE133 VGA Driver For Windows ME

• Please put the Support CD • When a welcome window
1 provided in your mainboard 2 appears on the screen,
package into the CD-ROM users should choose “Install
drive. Driver”.

• Click on the “VIA chipsets • Click on the “VIA KLE133

3 Driver”.
4 VGA Driver” to continue.

• Click on the “Install VGA • Follow the instruction on

5 Driver for Windows ME”. 6 screen to complete the
installation, after which
please restart your PC.

3-2.4 Install KLE133 VGA Driver Windows 2000

• Please put the Support CD • When a welcome window
1 provided in your mainboard 2 appears on the screen,
package into the CD-ROM users should choose “Install
drive. Driver”.

• Click on the “VIA chipsets • Click on the “VIA KLE133

3 Driver”.
4 VGA Driver” to continue.

• Click on the “Install VGA • Follow the instruction on

5 Driver for Win2000”. 6 screen to complete the
installation, after which
please restart your PC.

39

Downloaded from www.Manualslib.com manuals search engine

 75LIV

3-3 AC’97 AUDIO CODEC INSTALLATION

• Please put the Support CD • When a welcome window

1 provided in your mainboard 2 appears on the screen,
package into the CD-ROM users should choose “Install
drive. Driver”.

• Click on the “VIA Chipset • Click on the “AC’97 driver”.

3 Driver”. 4

Next
• Press “Next” button to
5 continue.

• When asking you to install

6 or remove the audio driver,
Next please select “Install” and
press “Next” button to
continue.

• After all the setup process

Finish 7 is finished, please restart
your computer by clicking
on Finish.

40

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 Software Setup

MEMO
MEMO

41

Downloaded from www.Manualslib.com manuals search engine

 75LIV

CHAPTER 4
BIOS SETUP

THE BIOS

• BIOS stands for Basic Input and Output System. It is sometimes called
ROM BIOS because it is stored in a Read-Only Memory(ROM) chip on
the mainboard. BIOS is the first program to run when you turn on your
computer.
• BIOS performs the following functions:
1. Initializing and testing hardware in your computer (a process called
“POST”, for Power On Self Test).
2. Loading and running your operating system.
3. Helping your operating system and application programs to manage
your PC hardware by means of a set of routines called BIOS Run-Time
Service.

This chapter contains the following topics :

4-1 WHAT IS BIOS SETUP

4-2 HOW TO RUN BIOS SETUP
4-3 WHAT IS CMOS
4-4 WHAT IS POST
4-5 BIOS UPGRADE
4-6 BIOS SETUP

42

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

4-1 WHAT IS BIOS SETUP

• BIOS setup is an interactive BIOS program that you need to run when:
1. Changing the hardware of your system. (For example: installing a new
Hard Disk etc.)
2. Modifying the behavior of your computer. (For example: changing the
system time or date, or turning special features on or off etc.)
3. Enhancing your computer’s behavior. (For example: speeding up
performance by turning on shadowing or cache)

4-2 HOW TO RUN BIOS SETUP

• To access BIOS setup menu, press < DEL > key after “POST”, and before
the OS is loaded. The BIOS usually displays the following message:

Press DEL to enter SETUP

4-3 WHAT IS CMOS

• CMOS is the memory maintained by a battery. The BIOS uses CMOS
to store the settings you have selected in SETUP. The CMOS also
maintains the internal clock. Every time you turn on your computer,
the BIOS Looks into CMOS for the settings you have selected and
configures your computer accordingly. If the battery is out of power,
the CMOS data will be lost and POST will issue a “CMOS invalid” or
“CMOS checksum invalid” message. If this happens, you have to replace
the battery and do some proper settings in SETUP.

4-4 WHAT IS POST

• POST is an acronym for Power On Self Test. POST will test all things the
BIOS does before the operating system is started. Each of POST routines
is assigned a POST code, a unique number which is sent to I/O port 080h
before the routine is executed.

4-5 BIOS UPGRADE

• System BIOS is incorporated into a Flash memory component of the
mainboard. Flash BIOS allows user to upgrade BIOS without the need
to replace an EPROM component.

43

Downloaded from www.Manualslib.com manuals search engine

 75LIV

• The upgrade utility can be loaded on a floppy diskette and used to provide
the capability to save, verify, and update the system BIOS. The upgrade
utility can be run from a hard disk drive or a network drive.

4-5.1 Before Upgrading BIOS

• It is highly recommended that you save a copy of the original mainboard
BIOS along with a Flash EPROM Programming utility (AWDFLASH.EXE)
to a bootable floppy disk in case you need to reinstall the BIOS later.

4-5.2 Upgrade Process

Note: Normally, to upgrade BIOS is unnecessary if the system is working

fine without any problem. Users should not upgrade the BIOS unless you
experience incompatible problems or need to create new features. However,
please read all information in this section before upgrading.

“AWDFLASH.EXE” is a Flash EPROM Programming utility that updates

the BIOS by uploading a new BIOS file to the programmable flash ROM
on the mainboard. This program only works in DOS environment, the
utility can not be executed in win95/98, ME, NT or WINDOWS 2000
environment.

Upgrading the system BIOS

Step 1. Please visit the board maker’s website, download latest BIOS file and
award flash utility “AWDFLASH.EXE”. The BIOS file format will be *.bin, of
which “*” stands for the specific file name.

Step 2. Create a bootable diskette. Then copy the BIOS file and award flash utility
“AWDFLASH.EXE” into the diskette.

Step 3. Insert the diskette into drive A, reboot your system and boot from the
diskette.

44

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

Step 4. Type awdflash *.bin /sn/py/cc and then press <Enter> to run BIOS
upgrade program. (*.bin depends on your mainboard model and version
code. Instead of typing “*”, you should type specific file name for your
specific mainboard).

Step 5. Please press <F1> or <F10> to exit or reset your system, Warning !
If the message “Write Fail” appears while Award “FLASH MEMORY
WRITER” is verifying Flash memory, just repeat the process. Please
DO NOT reset or turn off the system. If the award memory flash utility
is not able to update the BIOS successfully, your system may not be
able to boot up.

Step 6. You will need a message “CMOS checksum error-Default loaded” during
booting the system. Press <Del> to run CMOS setup utility, then reload
“LOAD SETUP DEFAULTS” or “Load Optimized Defaults” and save
this change.

45

Downloaded from www.Manualslib.com manuals search engine

 75LIV

Figure 1 : Award Flash Memory Writer Start Screen

Figure 2 : Award Flash Memory Writer Start Screen

46

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

The parameters of AWDFLASH.EXE

/sn: No original BIOS backup

/py: Program flash memory
/cc: Clear CMOS and update data auto matically after programming
/r : Reset system after programming

NOTE: User can type AWDFLASH /? to get further details about parameters.
Wrong usage of parameter will damage the BIOS information, so that we
strongly recommend user to leave parameters alone unless you realize their
function.

47

Downloaded from www.Manualslib.com manuals search engine

 75LIV

4-6 BIOS SETUP --- CMOS SETUP UTILITY

4-6.1 CMOS SETUP UTILITY
• This mainboard comes with the AWARD BIOS from AWARD Software Inc.
Enter the CMOS Setup Utility Main Menu by:

1. Turn on or reboot your system. After a series of diagnostic checks, the

following message will appear:

PRESS <DEL> TO ENTER SETUP

2. Press the <DEL> key and the main program screen will appear as follows.

CMOS Setup Utility - Copyright (C) 1984 - 2001 Award Software

Standard CMOS Features Frequency/Voltage Control

Advanced BIOS Features Load Optimized Defaults

Advanced Chipset Features Set Supervisor Password

Integrated Peripherals Set User Password

Power Management Setup SAVE & EXIT SETUP

PnP/PCI Configurations Exit Without Saving

SmartDoc Anti-burn Shield

Esc6 : Quit : Select Item

F106 : Save & Exit Setup

Time, Date, Hard Disk Type...

3. Use the arrow keys on your keyboard to select an option, and press
<Enter>. Modify the system parameters to reflect the options installed in
your system.
4. You may return to the Main Menu anytime by pressing <ESC>.
5. In the Main Menu, “SAVE AND EXIT SETUP” saves your changes and
reboots the system, and “EXIT WITHOUT SAVING” ignores your changes
and exits the program.

48

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

4-6.2 STANDARD CMOS SETUP

• Standard CMOS Setup records some basic system hardware configuration

and sets the system clock and error handling. You only need to modify the
configuration values of this option if you want to change your system
hardware configuration or when the data stored in the CMOS memory gets
lost or damaged.

Run the STANDARD CMOS SETUP as follows:

1. Choose “STANDARD CMOS SETUP” from the Main Menu and a screen
with a list of options will appear:

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

Standard CMOS Features

Date (mm:dd:yy)6 Tue, May 9 2001 Item Help

Time (hh:mm:ss)6 9 : 52 : 15 Menu Level

IDE Primary Master6 None

IDE Primary Slave6 None
IDE Secondary Master6 None
IDE Secondary Slave6 None

Drive A6 1.44M, 3.5 in.

Drive B6 None

Video6 EGA/VGA
Halt On6 All,But Keyboard

Base Memory6 640K

Extended Memory6 31744K
Total Memory6 32768K

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.

49

Downloaded from www.Manualslib.com manuals search engine

 75LIV

Date (mm:dd:yy) The BIOS determines the day of the week from the
other date information. This field is for information
only.
Press the left or right arrow key to move to the
desired field (date, month, year). Press the PgUp or
PgDn key to increment the setting, or type the de-
sired value into the field.

Time (hh:mm:ss) The time format is based on the 24-hour military-time

clock. For example, 1 p.m. is 13:00:00. Press the
left or right arrow key to move to desired field. Press
the PgUp or PgDn key to increment the setting, or
type the desired value into the field.

Primary / Secondary This field records the specifications for all non-SCSI
Master / Slave hard disk drives installed in your system. Refer to
the respective documentation on how to install the
drives.

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

IDE Primary Master

IDE HDD Auto-Detection6 Press Enter Item Help

Menu Level
IDE Primary Master6 Auto
Access Mode6 Auto

Capacity6 10243 MB

Cylinder6 19846
Head6 16
Precomp6 65535
Landing Zone6 19845
Sector6 63

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

50

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

Drive A / Drive B Select this field to the type(s) of floppy disk drive(s)
installed in your system. The choices are:
360KB, 5.25in;
1.2MB, 5.25in;
720KB, 3.5in;
1.44MB, 3.5in;
2.88MB, 3.5in;
None.

Video Select the type of primary video subsystem in your

computer. The BIOS usually detects the correct video
type automatically. The BIOS supports a secondary
video subsystem, but you do not select it in setup.

Halt On During the power-on self-test (POST), the computer

stops if the BIOS detects a hardware error. You can
tell the BIOS to ignore certain errors during POST
and continue the boot-up process.

Base Memory Typically 640KB. Also called conventional memory.

The DOS operating system and conventional
applications use this area.

Extended Memory Above the 1MB boundary. Early IBM personal

computers could not use memory above 1MB, but
current PCs and their software can use extended
memory.

Total Memory This option shows system memory capacity.

3. Press <ESC> to return to the Main Menu when you finish setting up all
items.

51

Downloaded from www.Manualslib.com manuals search engine

 75LIV

4-6.3 ADVANCED BIOS FEATURES

• ADVANCED BIOS FEATURES improves your system performance or sets
up system features according to your preference.

Run the ADVANCED BIOS FEATURES as follows:

1. Choose “ADVANCED BIOS FEATURES” from the Main Menu and a

screen with a list of options will appear:

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.

<F5>: Get the previous values. These values are the values with which the
user starts the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

52

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

Advanced BIOS Features

Virus Warning6 Disabled Item Help

CPU Internal Cache 6 Enabled Menu Level
External Cache6 Enabled
CPU L2 Cache ECC Checking Enabled
Quick Power On Self Test6 Enabled
First Boot Device6 Floppy
Second Boot Device6 HDD-0
Third Boot Device6 CDROM
Boot Other Device6 Enabled
Swap Floppy Drive6 Disabled
Boot Up Floppy Seek6 Enabled
Boot Up NumLock Status6 On
Gate A20 Option6 Fast
Typematic Rate Setting6 Disabled
Typematic Rate (Chars/Sec) 6
Typematic Delay (Msec)6 250
Security Option6 Setup
OS Select For DRAM > 64MB Non-OS2
Video BIOS Shadow6 Enabled
C8000-CBFFF Shadow6 Disabled
CC000-CFFFF Shadow6 Disabled
D0000-D3FFF Shadow6 Disabled
D4000-D7FFF Shadow6 Disabled
D8000-DBFFF Shadow6 Disabled
DC000-DFFFF Shadow6 Disabled

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

53

Downloaded from www.Manualslib.com manuals search engine

 75LIV

Virus Warning When enabled, you receive a warning message if a

program (specifically, a virus) attempts to write to the
boot sector or the partition table of the hard disk drive.
You should then run an antivirus program. Keep in
mind that this feature protects only the boot sector,
not the entire hard drive.

NOTE: Many disk diagnostic programs that access the boot sector table
can trigger the virus warning message. If you plan to run such a
program, we recommend that you disable the virus warning.

CPU Internal Cache/ Cache memory is additional memory that is much

External Cache faster than conventional DRAM (system memory).
CPUs from 486-type up contain internal cache
memory, and most, but not all, modern PCs have
additional (external) cache memory. When the CPU
requests data, the system transfers the requested
data from the main DRAM into cache memory, for
faster access by the CPU.

CPU L2 Cache ECC When you select Enabled, it will speed up memory
Checking checking when the external cache contains ECC
SRAMs.
The choices: Enabled; Disabled.

Quick Power On Self Select Enabled to reduce the amount of time required to
Test run the power-on self-test (POST). A quick POST skips
certain steps. We recommend that you normally enable
quick POST.

First/Second/Third/ The BIOS attempts to load the operating system from

Other Boot Device the devices in the sequence selected in these items.
The choices: Floppy; LS/ZIP; HDD; SCSI; CDROM;
Disabled.

Swap Floppy Drive When enabled, floppy drives A and B will be exchanging
without any physical connection and modification on the
cables.

54

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

Boot Up Floppy Seek When enabled, the BIOS tests (seeks) floppy drives
to determine whether they have 40 or 80 tracks. Only
360-KB floppy drives have 40 tracks; drives with
270KB, 1.2MB, and 1.44MB capacity all have 80
tracks. Because very few modern PCs have 40-track
floppy drives, we recommend that you set this field
to disabled to save time.

Boot Up NumLock Toggle between On or Off to control the state of

Status the NumLock key when the system boots. If On,
the numeric keypad is in numeric mode. If off, the
numeric keypad is in cursor control mode.

Gate A20 Option Gate A20 refers to the way the system addresses
memory above 1 MB (extended memory). When
set to Fast, the system chipset controls Gate A20.
When set to Normal, a pin in the keyboard control-
ler controls Gate A20. Setting Gate A20 to Fast
improves system speed, particularly with OS/2 and
Windows.
Typematic Rate Setting When Disabled, the following two items (Typematic Rate
and Typematic Delay) are irrelevant. Keystroke repeats
at a rate determined by the keyboard controller in your
system.
When Enabled, you can select a typematic rate and
typematic delay.

Typematic Rate (Chars When the typematic rate setting is enabled, you can
/ Sec) select a typematic rate (the rate at which character
repeats when you hold down a key) of 6, 8, 10, 12,
15, 20, 24, or 30 characters per second.

Typematic Delay Choices: 250; 500; 750; 1000. This option sets the
(Msec) time interval for displaying the first and the second
characters. If enabled, the time interval is optional.

55

Downloaded from www.Manualslib.com manuals search engine

 75LIV

Security Option If you have set a password, select whether the

password is required every time the System
boots, or only when you enter setup.
The choices: system; setup.

OS Select For DRAM > Select OS2 only if you are running OS/2 operating
64MB system with greater than 64MB of RAM on your
system.

Video BIOS Shadow Performance will be improved by copying Video

BIOS to Shadow RAM.

C8000-CBFFF to These options are used to shadow other expansion

DC000-DFFFF Shadow card ROMs.

3. Press <ESC> to return to the Main Menu when you finish setting up all
items.

56

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

4-6.4 ADVANCED CHIPSET FEATURES

• ADVANCED CHIPSET FEATURES is used to modify the values of chipset

buffers. These buffers control the system options.

Run the ADVANCED CHIPSET FEATURES as follows:

1. Choose “ADVANCED CHIPSET FEATURES” from the Main Menu and a

list of option will appear:

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.

<F5>: Get the previous values. These values are the values with which the
user starts the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

57

Downloaded from www.Manualslib.com manuals search engine

 75LIV

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

Advanced Chipset Features

DRAM Timing By SPD Enabled Item Help

DRAM Clock6 133M Menu Level
SDRAM Cycle Length6 3
Bank Interleave Disabled
DRAM Drive Strength6 Auto
DRAM Drive Value6 2F
Memory Hole6 Disabled
PCI Master Pipeline Req6 Enabled
P2C/C2P Concurrency6 Disabled
Fast R-W Turn Around6 Disabled
System BIOS Cacheable6 Disabled
Video RAM Cacheable6 Disabled
AGP Aperture Size6 64M
AGP Mode 4X
AGP Driving Control6 Auto
AGP Driving Value6 DA6
AGP Fast Write6 Disabled
OnChip USB6 Enabled
OnChip USB 26 Enabled
USB Keyboard Support6 Disabled
OnChip Sound6 Auto
OnChip Modem6 Auto
CPU to PCI Write Buffer6 Enabled
PCI Dynamic Bursting6 Enabled
PCI Master 0 WS Write6 Enabled
PCI Delay Transaction6 Disabled
PCI#2 Access #1 Retry6 Enabled
AGP Master 1 WS Write6 Disabled
AGP Master 1 WS Read6 Disabled

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

58

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

DRAM Timing by SPD When this item Enabled, DRAM Timing is set by SPD
SPD (Serial Presence Detect) is located on the
memory modules, BIOS reads information coded in
SPD during system boot up.

DRAM Clock The value represents the performance parameters

of the installed memory chips (DRAM). Do not
change the value from the factory setting unless you
install new memory that has a different performance
rating .

SDRAM Cycle Length Select CAS latency time in HCLKs of 2 or 3. The

Time system designer already set the values. Do not
change the values from the default value unless you
change specifications of the installed DRAM or the
installed CPU.

Bank Interleave The choices: Disabled; 2 Bank; 4 Bank.

DRAM Drive Strength Leave this item with Auto mode.

The choices: Auto; Manual.

DRAM Drive Value When “DRAM Drive Strength” is set to “Auto”, this
item will be unable to be selected. We don’t
recommend user to adjust this item.

Memory Hole In order to improve performance, certain space in

memory is reserved for ISA cards. This memory must
be mapped into the memory space below 16MB.
The choices: 15M-16M; Disabled.

PCI Master Pipeline Use default setting.

Req

59

Downloaded from www.Manualslib.com manuals search engine

 75LIV

P2C/C2P Concurrency This item allows you to enable/disable the PCI to

CPU, CPU to PCI concurrency.
The choices: Enabled; Disabled.

Fast R-W Turn Around This item controls the DRAM timing. It allows you to
enable / disable the fast read / write turn around.
The choices: Enabled; Disabled.

System BIOS selecting Enabled allows caching of the system

Cacheable BIOS ROM at F0000h-FFFFFh, resulting in better
system performance.

Video RAM Cacheable electing Enabled allows caching of the video memory
(RAM) at A0000h to AFFFFh, resulting in better video
performance.
However, check your AGP manual to find out if any
compatibility problem exists.

AGP Aperture Size Series of options are available: 4, 8, 16, 32, 64, 128
or 256 MB. Memory mapped and graphics data
structures can reside in a Graphics Aperture. This
area is like a linear buffer. BIOS will automatically
report the starting address of this buffer to the O.S.
The default setting is 64MB.

AGP Mode This item allows you to select AGP mode.

The choices: 1X; 2X; 4X.

AGP Driving Control This item allows you to adjust the AGP driving force.
Choose Manual to key in a AGP Driving Value in the
next selection. This field is recommended to set in
Auto for avoiding any error in your system.
The choices: Manual; Auto.

AGP Driving Value This item allows you to adjust the AGP driving force.
The choices: Min=0000 ~ Max=00FF.

60

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

AGP Fast Write This item will enable the AGP model into fast write
mode. If your graphics card does not support this
function, please do not enable this function.

OnChip USB/USB2 This should be enabled if our system has a USB

installed on the system board and you wish to use
it. Even when so equipped, if you add a higher per-
formance controller, you will need to disable this
feature. The choices: Enabled; Disabled.

USB Keyboard Enable function when the USB keyboard is being used
Support . When the AT keyboard is being used, choose
disabled.

OnChip Sound Enabled: Turn on AC’97 codec chip controller.

Disabled: Turn off AC’97 codec chip controller or
user can plug external add-on sound card.

OnChip Modem Select Auto to use the on-chip Modem capability of

your system. This field must be Disabled, if there
is NO AMR modem card installed.
The choices: Auto; Disabled.

CPU to PCI Write When this field is Enabled, writes from the CPU to
Buffer the PCI bus are buffered, CPU speed runs faster
than PCI bus. When Disabled, the writes are not
buffered and the CPU must wait until the write is
complete before starting another write cycle.
The choices: Enabled; Disabled.

PCI Dynamic Bursting When Enabled, every write transaction goes to the
write buffer. Burstable transactions then burst on the
PCI bus and nonburstable transactions don’t.
The choices: Enabled; Disabled.

61

Downloaded from www.Manualslib.com manuals search engine

 75LIV

PCI Master 0 WS Write When Enabled, writes to the PCI bus are executed
with zero wait states.
The choices: Enabled; Disabled.

Memory Parity/ECC This item enabled to detect the memory parity and
Check Error Checking & Correcting.
The choices: Enabled; Disabled.

PCI Delay Transaction Leave this field at default

PCI #2 Access #1 Retry Leave this field at default

AGP Master 1 ws write Leave this field at default

AGP Master 1 ws read Leave this field at default

3. Press <ESC> to return to the Main Menu when you finish setting up all
items.

62

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

4-6.5 INTEGRATED PERIPHERALS

• INTEGRATED PERIPHERALS option allows you to get some information

inside your system when it is working.

Run the INTEGRATED PERIPHERALS as follows:

1. Choose “INTEGRATED PERIPHERALS” from the Main Menu and a list

of options will appear:

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.

<F5>: Get the previous values. These values are the values with which the
user starts the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

63

Downloaded from www.Manualslib.com manuals search engine

 75LIV

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

Integrated Peripherals

On-Chip IDE Channel06 Enabled Item Help

On-Chip IDE Channel16 Enabled Menu Level
IDE Prefetch Mode6 Enabled
Primary Master PIO6 Auto
Primary Slave PIO6 Auto
Secondary Master PIO6 Auto
Secondary Slave PIO6 Auto
Primary Master UDMA6 Auto
Primary Slave UDMA6 Auto
Secondary Master UDMA6 Auto
Secondary Slave UDMA6 Auto
Init Display First6 PCI Slot
IDE HDD Block Mode6 Enabled
Onboard FDD Controller6 Enabled
Onboard Serial Port 16 Auto
Onboard Serial Port 26 Auto
UART 2 Mode6 Standard
IR Function Duplex6 Half
TX, RX inverting enable6 No, Yes
Onboard Parallel Port6 378/IRQ7
Onboard Parallel Mode6 Normal
ECP Mode Use DMA6 3
Parallel Port EPP Type6 EPP1.9
Onboard Legacy Audio6 Enabled
Sound Blaster6 Disabled
SB I/O Base Address6 220H
SB IRQ Select6 IRQ 5
SB DMA Select6 DMA 1
MPU-4016 Disabled
MPU-401 I/O Address6 330-333H
Game Port (200-207H)6 Enabled

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

64

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

On-Chip IDE channel The chipset contains a PCI IDE interface with
0/1 support from two IDE channels. Select Enabled
to activate the first and/or the second IDE
interface. Select Disabled to inactivate an interface
if you install a primary and/or second add-on IDE
interface.
The choices: Enabled; Disabled.

IDE Prefetch Mode The on-board IDE drive supports IDE perfecting for
faster drive accesses. If the IDE device doesn’t
support perfecting, set this field to Disabled.
The choices: Enabled; Disabled.

Primary Choose Auto or Mode 0~4. The BIOS will detect the
Master / Slave PIO HDD mode type automatically when you choose
Secondary Auto. You need to set to a lower mode than Auto
Master / Slave PIO when your hard disk becomes unstable.
The choices: Auto; Mode 0; Mode 1; Mode 2; Mode
3; Mode 4.

Primary Ultra DMA33/66/100 implementation is possible only

Master / Slave UDMA if your IDE hard drive supports it, if the operating
Secondary environment includes a DMA drive, and if your
Master / Slave UDMA system software supports Ultra DMA33/66/100.
Select “Auto” to enable BIOS support.
The choices: Auto; Disabled.

Init Display First Initialize the AGP video display before initializing any
other display device on the system. Thus the AGP
display becomes the primary display.

IDE HDD Block Mode Block mode is also called block transfer, multiple
commands, or multiple sector read/write. If your IDE
hard drive supports block mode (most new drives
do), select Enabled for automatic detection of the
optimal number of block read/write per sector the
drive can support.
The choices: Enabled; Disabled.

65

Downloaded from www.Manualslib.com manuals search engine

 75LIV

Onboard FDC Select Enabled if your system has a floppy drive

Controller controller (FDC) installing in the system board and
you want to use it. If you install add-in FDC or the
system has no floppy drive, select Disabled in this
field.
The choices: Enabled; Disabled.

Onboard Serial Select a logical COM port name and matching

Port 1 / Port 2 address for the first and second serial ports.
Select an address and corresponding interrupt
for the first and second serial ports.

UART 2 Mode This item allows you to select which mode for the
Onboard Serial Port 2.
The choices: Standard; HPSIR; ASKIR

IR Function Duplex This item allows you to select the IR half / full
duplex function.
The choices: Half; Full.

TX, RX inverting This item allows you to enable the TX, RX inverting
enable which depends on different H/W requirement. This
field is not recommended to change its default
setting.
The choices: “No, No”; “No, Yes”; “Yes, No”; “Yes,
Yes”.

Onboard Parallel Port This item allows you to determine onboard parallel
port controller I/O address setting.
The choices: 378H/IRQ7; 278H/IRQ5; 3BC/IRQ7;
Disabled.

Onboard Parallel Mode Select an operating mode for the on-board parallel
(printer) port. Select Normal, Compatible, or SPP
unless you are certain your hardware and software
both support one of the other available modes.

66

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

ECP Mode Use DMA Select a DMA channel for the port.

Parallel Port EPP Type Select EPP port type 1.7 or 1.9
The choice: EPP1.7, 1.9.

Onboard Legacy Audio This field controls the onboard audio.

• Sound Blaster
• SB I/O Base Address
• SB IRQ Select
• SB DMA Select
• MPU-401
• MPU-401 I/O Address
• Game Port (200-207H)

3. Press <ESC> to return to the Main Menu when you finish setting up all
items.

67

Downloaded from www.Manualslib.com manuals search engine

 75LIV

4-6.6 POWER MANAGEMENT SETUP

• POWER MANAGEMENT SETUP allows you to set the system’s power

saving functions.

Run the POWER MANAGEMENT SETUP as follows:

1. Choose “POWER MANAGEMENT SETUP” from the Main Menu and a

list of options will appear:

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

Power Management Setup

ACPI Function6 Enabled Item Help

Power Management6 Press Enter Menu Level
ACPI Suspend Type6 S1(POS)
PM Control by APM6 Yes
Video Off Option6 Suspend -> Off
Video Off Method6 V/H SYNC+Blank
MODEM Use IRQ6 3
Soft-Off by PWRBTN6 Instant-Off
State After Power Failure Auto
Wake Up Events6 Press Enter

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.

<F5>: Get the previous values. These values are the values with which the
user starts the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

68

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

ACPI Function Select Enabled only if your computer’s operating

system supports the Advanced Configuration and
Power Interface (ACPI) specification.

Power Management
• When this option is chosen, the following item appears for user’s
configuration.

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

Power Management

Power Management6 User Define Item Help

HDD Power Down6 Disable Menu Level
Doze Mode6 Disable
Suspend Mode6 Disable

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

* Power Management This option allows you to select the type (or degree)
of power saving for Doze, Standby, and Suspend
modes.
This table describes each power management
mode:

Maximum power savings. Only Available for SL CPUs.

Max Saving
Inactivity period is 1 minute in each mode.

Set each mode individually. Select time-out period in

User Define
the section for each mode stated below.

Minimum power savings. Inactivity period is 1 hour in

Min Saving
each mode (except the hard drive).

69

Downloaded from www.Manualslib.com manuals search engine

 75LIV

* HDD Power Down When enabled and after the set time of system
inactivity, the hard disk drive will be powered down
while all other devices remain active.

* Doze Mode When enabled and after the set time of system
inactivity, the CPU clock will run at slower speed
while all other devices still operate at full speed.

* Suspend Mode After the selected period of system inactivity, the

chipset enters a hardware suspend mode, stopping
the CPU clock and possibly causing other system
devices to enter power management modes.

ACPI Suspend Type This item allows you to select the ACPI suspend
type. You can select S3(STR) for suspending to
DRAM or S1(POS) for power on suspend under
Windows 98 ACPI mode.
The choices: S1(POS), S3(STR).

PM Control by APM When enabled, an Advanced Power Management

device will be activated to enhance the Max. Power
Saving mode and stop the CPU internal clock, If
Advanced Power Management (APM) is installed
on your system, selecting Yes gives better power
savings. If the Max. Saving is not enabled, this will
be present to No.

Video Off Option When enabled, this feature allows the VGA adapter
to operate in a power saving mode.

Always On Monitor will remain on during power saving modes.

Monitor blanked when the systems enters the Sus-

Suspend -->Off
pend mode.

Monitor blanked when the system enters either Su-

All Modes -->Off
spend or Standby modes.

70

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

Video Off Method This determines the manner by which the monitor is
blanked.

This selection will cause the system to turn off the vertical
V/H SYNC + and horizontal synchronization ports and write blanks to
Blank the video buffer.

Blank Screen This option only writes blanks to the video buffer.

Select this option if you monitor supports the Display Power

DPMS Supports Management Signaling (DPMS) standard of the Video Elect-
ronics Standards to select video power management values.

MODEM Use IRQ Name the interrupt request (IRQ) line assigned to
the modem (if any) on your system. Activity of the
selected IRQ always awakens the system.
The choices: 3; 4; 5; 7; 9; 10; 11; NA.

Soft-Off by PWRBTN When Enabled, turning the system off by pressing

the on/off button places the system in a very low-
power-usage state.

State After Power This field lets you determine the state that your PC
Failure returns to after a power failure.
The choices: On; Off; Auto.

71

Downloaded from www.Manualslib.com manuals search engine

 75LIV

Wake Up Events
• When this option is chosen, the following item appears for user’s
configuration.

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

Wake Up Events

VGA6 OFF Item Help

LPT & COM6 LPT/COM Menu Level
HDD & FDD6 ON
PCI Master6 OFF
Wake Up On LAN/Ring6 Disabled
RTC Alarm Resume6 Disabled
Date (of Month)6 0
Resume Time (hh:mm:ss) 0 0 0
Primary INTR6 ON
IRQ Activity Monitoring6 Press Enter

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

* VGA When Enabled, you can set the VGA awakens the
system

* LPT & COM When LPT & COM is ON, any activity from one of
the listed system peripheral devices or IRQs wakes
up the system.

* HDD & FDD When HDD & FDD is ON, any activity from one of
the listed system peripheral devices wakes up the
system.

* PCI Master When PCI Master is ON, any activity from one of
the listed system peripheral devices wakes up the
system.

72

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

* Wake Up On LAN/ An input signal on the serial Ring Indicator (RI) line
Ring (in other words, an incoming call on the modem)
awakens the system from a soft off state.
The choices: Enabled; Disabled.

* RTC Alarm Resume When Enabled, you can set the data and time at
which the RTC (Real Time Clock) alarm awakens
the system from suspend mode.
The choices: Disabled (default); Enabled.

* Date (of Month) Set a certain date when RTC Alarm Resume
option is Enabled to awaken the system. This
option is concurrent with Resume Time option.

* Resume Time (hh: Set a certain time when RTC Alarm Resume
mm:ss) option is Enabled to awaken the system. This
option is concurrent with Date option.

* Primary INTR Leave this field at default

73

Downloaded from www.Manualslib.com manuals search engine

 75LIV

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

4-6.7 PNP / PCI CONFIGURATION

• PNP/PCI CONFIGURATION allows you to modify the system’s power

saving functions.

Run the PNP/PCI CONFIGURATION as follows:

1. Choose “PNP/PCI CONFIGURATION” from the Main Menu and a screen

with a list of options will appear:

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

PnP/PCI Configurations

PNP OS Installed6 No Item Help

Reset Configuration Data6 Disabled Menu Level

Resources Controlled By6 Auto(ESCD)

IRQ Resources6 Press Enter
DMA Resources6 Press Enter

PCI/VGA Palette Snoop6 Disabled

Assign IRQ For VGA6 Enabled
Assign IRQ For USB6 Enabled
PCI SLOT 1/5 IRQ Assigned Auto
PCI SLOT 2/6 IRQ Assigned Auto
PCI SLOT 3 IRQ Assigned Auto
PCI SLOT 4 IRQ Assigned Auto

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys. An explanation of the
<F> keys follows:

<F1>: “Help” gives options available for each item.

<F5>: Get the previous values. These values are the values with which the
user starts the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

75

Downloaded from www.Manualslib.com manuals search engine

 75LIV

PNP OS Installed Select Yes if the system operating environment is

Plug-and-Play aware (e.g., Windows95).

NOTE: BIOS will automatically disable all PnP resources except the boot
device card when you select Yes on Non-PnP operating system.

Reset Configuration Normally, you leave this Disabled. Select Enabled

Data to reset Extended System Configuration Data
(ESCD), when you exit Setup if you have installed
a new add-on and the system reconfiguration has
caused such a serious conflict that the operating
system cannot boot.

Resource Controlled The Plug and Play AwardBIOS can automatically

By configure all the boot and Plug and Play-compatible
devices. If you select Auto, all the interrupt request
(IRQ) and DMA assignment fields disappear, as the
BIOS automatically assigns them.

IRQ Resources Press Enter. Please refer to the list below:

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

IRQ Resources

IRQ-3 assigned to PCI/ISA PnP Item Help

IRQ-4 assigned to PCI/ISA PnP Menu Level
IRQ-5 assigned to PCI/ISA PnP
IRQ-7 assigned to PCI/ISA PnP
IRQ-9 assigned to PCI/ISA PnP
IRQ-10 assigned to PCI/ISA PnP
IRQ-11 assigned to PCI/ISA PnP
IRQ-12 assigned to PCI/ISA PnP
IRQ-14 assigned to PCI/ISA PnP
IRQ-15 assigned to PCI/ISA PnP

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

76

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

DMA Resources Press Enter. Please refer to the list below:

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

DMA Resources

DMA-0 assigned to PCI/ISA PnP Item Help

DMA-1 assigned to PCI/ISA PnP Menu Level
DMA-3 assigned to PCI/ISA PnP
DMA-5 assigned to PCI/ISA PnP
DMA-6 assigned to PCI/ISA PnP
DMA-7 assigned to PCI/ISA PnP

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

PCI/VGA Palette Snoop This option allows the BIOS to preview VGA status,
and to modify the information delivered from the
feature Connector of the VGA card to MPEG card.
This option can solve the display inversion to black
after you have used MPEG card.

Assign IRQ for VGA Select Enabled if you system has a VGA controller
and you have one or more VGA devices connected.
If you are not using your system’s VGA controller,
select Disabled to free the IRQ resource.

Assign IRQ for USB Select Enabled if you system has a USB controller
and you have one or more USB devices connected.
If you are not using your system’s USB controller,
select Disabled to free the IRQ resource.

PCI SLOT1/5, 2/6, 3, 4 These options allow you to assign an IRQ for each
IRQ Assigned PCI SLOT and this is a useful function when you
want to fix the IRQ conflict for a specific device. The
options are available: Auto, 3, 4, 7, 9, 10, 11.

3. Press <ESC> to return to the Main Menu when you finish setting up all
items.

77

Downloaded from www.Manualslib.com manuals search engine

 75LIV

4-6.8 SMARTDOC ANTI-BURN SHIELD

• This section helps you to get more information about your system including CPU
temperature, FAN speed and voltage. It is recommended that you contact with
your mainboard supplier to get proper values about the setting of the CPU
temperature.

Run the “SMARTDOC ANTI-BURN SHIELD” as follows:

1. Choose “SMARTDOC ANTI-BURN SHIELD” from the Main Menu and a

screen with a list of options will appear:

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

SmartDoc Anti-Burn Shield

CPUFan Warning Speed Disabled Item Help

Shutdown For CPUFan Disabled Menu Level
Current CPUFAN1 Speed 5120 RPM
Current CPUFAN2 Speed 0 RPM
Vcore 1.53V
VDD 3.34V
3.3V 3.28V
5V 5.00V
12V 11.76V

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.

<F1>: “Help” gives options available for each item.

<F5>: Get the previous values. These values are the values with which the
user starts the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

78

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

CPUFan Warning This feature prevents the misfunction of the CPU

Speed cooling fan. When CPU cooling fan speed lower than
value you selected in this field, the BIOS will send
out sequence of beeps sound or send out a warning
message “Your CPU FAN speed is too slow”.

Shutdown For CPUFan This feature prevents your CPU damaged by over
heat, but the difference between features “Shutdown
For Temperature” and “Shutdown For CPUFan”
is that BIOS detects CPU cooling fan speed not CPU
Temperature in this field, when CPU FAN speed
lower than the value that you select in this field, the
BIOS will shutdown your system within 3 seconds.

Warning!!! Do not enable feature “Shutdown For CPUFan” without

CPU cooling fan connecting to onboard fan connector FAN1; otherwise,
your system will not be able to boot.

Current CPUFAN1 Shows current CPUFAN1 speed. The fan must provide
Speed rotary pulse. (Normally these types of fan have a
three-wire connector)

Current CPUFAN2 Show current CPUFAN2 speed. The fan must provide
Speed rotary pulse. (Normally these types of fan have a
three-wire connector)

Vcore/VDD/3.3V/5V/ Show power supply actual voltage value.

12V

3. Press <ESC> to return to the Main Menu when you finish setting up all
items.

79

Downloaded from www.Manualslib.com manuals search engine

 75LIV

4-6.9 FREQUENCY/VOLTAGE CONTROL

Run the “FREQUENCY/VOLTAGE CONTROL” as following:

1. Choose “FREQUENCY/VOLTAGE CONTROL” from the Main Menu and

a screen with a list of options will appear:

CMOS Setup Utility - Copyright (C) 1984-2001 Award Software

Frequency Control

Redstorm Overclocking Tech Press Enter Item Help

Auto Detect DIMM/PCI Clk6 Enabled Menu Level
Spread Spectrum Modulated Disabled
CPU Host/PCI Clock6 Default

:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

2. Use one of the arrow keys to move between options and modify the
selected options by using PgUp / PgDn / + / - keys.

<F1>: “Help” gives options available for each item.

<F5>: Get the previous values. These values are the values with which the
user starts the current session.
<F6>: Load all options with the BIOS default values.
<F7>: Load all options with the Setup default values.

80

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

RedStorm Press “Enter” to execute this function, by which BIOS

Overclocking Tech will detect1 CPU Frequency, until the unacceptable
one is reached. BIOS will then stop and reboot
automatically with the optimal CPU Frequency.
If system does not reboot after Frequency detection,
user should reboot system manually.

Auto Detect To reduce the occurrence of electromagnetic

DIMM/PCI CLK interference (EMI), the BIOS detects the presence
or absence of components in DIMM and PCI slots
and turns off system clock generator pulses against
empty slots.

Spread Spec- When the system clock generator pulses, the

trum Modulated extreme values of the pulse generate excess EMI.
Enabling pulse spectrum spread modulation
changes the extreme values from spikes to flat
curves, thus reducing EMI. This benefit may in some
cases be outweighed by problems with timing-critical
devices, such as a clock-sensitive SCSI device.

CPU Host/PCI Select Default or select a timing combination for the

Clock CPU and the PCI bus. When set to Default, the BIOS
uses the actual CPU and PCI bus clock values.

3. Press <ESC> to return to the Main Menu when you finish setting up all
items.

81

Downloaded from www.Manualslib.com manuals search engine

 75LIV

4-6.10 LOAD OPTIMIZED DEFAULTS

• When you press <Enter> on this item, you will get a confirmation dialog
box with a message similar to:

“ Load Optimized Defaults (Y/N) ? N ”

“Y” is for “Yes”, and “N” is for “No”.

Pressing “Y” loads the BIOS default values that are factor settings for opti-
mal performance of system operations.

82

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

4-6.11 SET SUPERVISOR / USER PASSWORD

• These two options allow you to set your system passwords. Normally, the
supervisor has a higher priority to change the CMOS setup option than
the users. The way to set up the passwords for both Supervisor
and Users are as follows:

1. Choose “Change Password” in the Main Menu and press <Enter>. Then
following message appears:

“Enter Password : “

2. The first time you run this option, enter your password up to 8 characters
and press <Enter>. (The screen does not display the entered characters.)
3. After you enter the password, the following message appears prompting
you to confirm the password:

“Confirm Password : “

4. Enter the same password “exactly” the same as you have just typed to
confirm the password and press <Enter>.
5. Move the cursor to Save & Exit Setup to save the password.
6. If you need to delete the password entered before, choose the Supervisor
Password and press <Enter>. It will delete the password that you have
entered before.
7. Move the cursor to Save & Exit Setup to save the option you have just
configured; otherwise the old password will still be there the next time
you turn your system on.
8. Press <Enter> to exit to the Main Menu.

NOTE: If you forget or lose the password, the only way to access the
system is to clear the CMOS RAM. All setup informations will be lost and
you need to run the BIOS setup program again.

83

Downloaded from www.Manualslib.com manuals search engine

 75LIV

4-6.12 SAVE & EXIT SETUP

• SAVE & EXIT SETUP allows you to save all modifications you have
specified into the CMOS memory. Highlight this option on the Main Menu
and the following message appears:

“ SAVE to CMOS and EXIT (Y/N) ? Y “

“Y” is for “Yes”, and “N” is for “No”.

Press <Enter> key to save the configuration changes.

4-6.13 EXIT WITHOUT SAVING

• EXIT WITHOUT SAVING option allows you to exit the Setup Utility
without saving the modifications that you have specified. Highlight
this option on the Main Menu and the following message appears:

“ Quit Without Saving (Y/N) ? N “

“Y” is for “Yes”, and “N” is for “No”.

You may change the prompt to “Y” and press <Enter> key to leave this
option .

84

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4 BIOS Setup

MEMO
MEMO

85

Downloaded from www.Manualslib.com manuals search engine

 75LIV

APPENDICES

APPENDIX-1 TECHNICAL TERMS

APPENDIX-2 IDENTIFYING BIOS VERSION/
BIOS PART NUMBER
APPENDIX-3 IDENTIFYING MAINBOARD
MODEL NUMBER

86

Downloaded from www.Manualslib.com manuals search engine

 Appendix

APPENDIX-1 TECHNICAL TERMS

Technical Terms Introduction

Tech Term Meaning
AGP Accelerated Graphic Port
AMR Audio Modem Riser
ACR Advanced Communication Riser
CPU Central Processing Unit
CMOS Complementary Metal Oxide Semiconductor
CRIMM Continuity RIMM
CNR Communication and Networking Riser
DMA Direct Memory Access
DMI Desktop Management Interface
DIMM Dual Inline Memory Module
DRAM Dynamic Random Access Memory
DDR Double Data Rate
ECP Extended Capabilities Port

ESCE Extended System Configuration Data

ECC Error Check and Correct
EPP Exhanced Parallel Port
FDD Floppy Disk Device
IDE Integrated Dual Channel Enhanced
IRQ Interrupt ReQuest
I/O Input/Output
LAN Local Area Network
LBA Logical Block Addressing
LED Local Emitting Diode
MHz Megahertz
PNP Plug & Play

USB Universal Serial Bus

VCM Virtual Channel Memory

87

Downloaded from www.Manualslib.com manuals search engine

 75LIV

APPENDIX-2 IDENTIFYING BIOS VERSION AND BIOS

PART NUMBER
• When you boot up your computer, you may see a screen which shows
your computer is phoenixnet™ enabled. Please see Picture-1 below for
an illustration.
• When the screen shows up press “Tab” key for BIOS information.

Picture-1

88

Downloaded from www.Manualslib.com manuals search engine

 Appendix

• See Picture-2 below for BIOS version and BIOS part number identification.

Picture-2
2

1. BIOS VERSION
example: REV T2.1
2. BIOS ID STRING
example: 6A69RSNCC

89

Downloaded from www.Manualslib.com manuals search engine

 75LIV

APPENDIX-3 IDENTIFYING MAINBOARD MODEL NUMBER

• Usually the mainboard model number is labeled on the side of ISA or PCI
slot. Please see the picture below for an illustration:

1. MAINBOARD MODEL NUMBER

example: SL-65KV2

2. MAINBOARD SERIAL NUMBER

example: 0012000T005679

90

Downloaded from www.Manualslib.com manuals search engine

 Appendix

MEMO
MEMO

91

Downloaded from www.Manualslib.com manuals search engine