PRODUCT DATA SHEET December 15, 2014 (Revision of December 1, 2012)
SIGMAGUARD™ 730
DESCRIPTION
Two-component, high solids polyamine cured phenolic epoxy coating
PRINCIPAL CHARACTERISTICS
• Tank coating with good chemical resistance against a wide range of chemicals
• Short curing periods
• Good low-temperature curing
• Easy to clean
• Can be used under insulation up to 150°C (300°F)
COLOR AND GLOSS LEVEL
• Offwhite, cream
• Gloss
BASIC DATA AT 20°C (68°F)
Data for mixed product
Number of components One
Mass density 1.4 kg/l (11.7 lb/US gal)
Volume solids 78 ± 2%
VOC (Supplied) Directive 1999/13/EC, SED: max. 169.0 g/kg
max. 242.0 g/l (approx. 2.0 lb/US gal)
Recommended dry film thickness 150 µm (6.0 mils)
Theoretical spreading rate 5.2 m²/l for 150 µm (209 ft²/US gal for 6.0 mils)
Dry to touch 3 hours
Overcoating Interval Minimum: 8 hours
Maximum: 28 days
Full cure after See curing table
Shelf life Base: at least 12 months when stored cool and dry
Hardener: at least 24 months when stored cool and dry
Notes:
- See ADDITIONAL DATA – Spreading rate and film thickness
- See ADDITIONAL DATA – Overcoating intervals
- See ADDITIONAL DATA – Curing time
RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURES
Substrate conditions
• Steel; blast cleaned to a minimum of ISO-Sa2½, blasting profile 40 – 70 µm (1.6 – 2.8 mils)
• Previous coat of approved coating must be dry and free from any contamination
Ref. 7459 Page 1/5
PRODUCT DATA SHEET December 15, 2014 (Revision of December 1, 2012)
SIGMAGUARD™ 730
Substrate temperature and application conditions
• Substrate temperature during application and curing should be above 5°C (41°F)
• Substrate temperature during application should be at least 3°C (5°F) above dew point
INSTRUCTIONS FOR USE
Mixing ratio by volume: base to hardener 75:25 (3:1)
• The temperature of the mixed base and hardener should preferably be above 15°C (59°F), otherwise extra thinner may be
required to obtain application viscosity
• Adding too much thinner results in reduced sag resistance and slower cure
• Thinner should be added after mixing the components
Induction time
Allow induction time before use
Mixed product induction time
Mixed product Induction time
temperature
15°C (59°F) 15 minutes
20°C (68°F) 10 minutes
25°C (77°F) 5 minutes
Pot life
1.5 hours at 20°C (68°F)
Note: See ADDITIONAL DATA – Pot life
Air spray
Recommended thinner
THINNER 91-92
Volume of thinner
5 - 15% for a one coat application of 150 µm (6.0 mils) DFT
Nozzle orifice
1.8 – 2.0 mm (approx. 0.070 – 0.079 in)
Nozzle pressure
0.3 - 0.4 MPa (approx. 3 - 4 bar; 44 - 58 p.s.i.)
Ref. 7459 Page 2/5
PRODUCT DATA SHEET December 15, 2014 (Revision of December 1, 2012)
SIGMAGUARD™ 730
Airless spray
Recommended thinner
THINNER 91-92
Volume of thinner
0 - 10% for a one coat application of 150 µm (6.0 mils) DFT
Nozzle orifice
Approx. 0.53 – 0.69 mm (0.021 – 0.027 in)
Nozzle pressure
15.0 MPa (approx. 150 bar; 2176 p.s.i.)
Brush/roller
• For stripe coating and spot repair only
Cleaning solvent
THINNER 90-53
ADDITIONAL DATA
Spreading rate and film thickness
DFT Theoretical spreading rate
125 µm (5.0 mils) 6.2 m²/l (250 ft²/US gal)
150 µm (6.0 mils) 5.2 m²/l (209 ft²/US gal)
Note: Maximum DFT when brushing: 100 µm (4.0 mils)
Overcoating interval for DFT up to 150 µm (6.0 mils)
Overcoating with... Interval 5°C (41°F) 10°C (50°F) 20°C (68°F) 30°C (86°F) 40°C (104°F)
itself Minimum 32 hours 24 hours 8 hours 4 hours 3 hours
Maximum 28 days 28 days 28 days 14 days 7 days
Note: Surface should be dry and free from any contamination
Ref. 7459 Page 3/5
PRODUCT DATA SHEET December 15, 2014 (Revision of December 1, 2012)
SIGMAGUARD™ 730
Curing time for DFT up to 150 μm (6.0 mils)
Substrate temperature Minimum curing time before Minimum curing time before
transport of aliphatic petroleum transport of cargoes without
products and ballast water and note 4, 7, 8 or 11
tanktest with seawater
5°C (41°F) 10 days 17 days
10°C (50°F) 7 days 14 days
20°C (68°F) 3 days 5 days
30°C (86°F) 60 hours 4 days
40°C (104°F) 36 hours 3 days
Notes:
- Minimum curing time before transport of cargoes with note 4,7,8 or 11: 3 months
- For detailed information on resistance and resistance notes, please refer to the latest issue of the cargo resistance list
- Adequate ventilation must be maintained during application and curing (please refer to INFORMATION SHEETS 1433 and 1434)
Pot life (at application viscosity)
Mixed product temperature Pot life
15°C (59°F) 3 hours
20°C (68°F) 1.5 hours
25°C (77°F) 1 hour
30°C (86°F) 30 minutes
SAFETY PRECAUTIONS
• For paint and recommended thinners see INFORMATION SHEETS 1430, 1431 and relevant Material Safety Data Sheets
• This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between
the wet paint and exposed skin or eyes
WORLDWIDE AVAILABILITY
It is always the aim of PPG Protective and Marine Coatings to supply the same product on a worldwide basis. However, slight
modification of the product is sometimes necessary to comply with local or national rules/circumstances. Under these
circumstances an alternative product data sheet is used.
Ref. 7459 Page 4/5
PRODUCT DATA SHEET December 15, 2014 (Revision of December 1, 2012)
SIGMAGUARD™ 730
REFERENCES
• CONVERSION TABLES INFORMATION SHEET 1410
• EXPLANATION TO PRODUCT DATA SHEETS INFORMATION SHEET 1411
• SAFETY INDICATIONS INFORMATION SHEET 1430
• SAFETY IN CONFINED SPACES AND HEALTH SAFETY, EXPLOSION HAZARD – INFORMATION SHEET 1431
TOXIC HAZARD
• SAFE WORKING IN CONFINED SPACES INFORMATION SHEET 1433
• DIRECTIVES FOR VENTILATION PRACTICE INFORMATION SHEET 1434
• CLEANING OF STEEL AND REMOVAL OF RUST INFORMATION SHEET 1490
• SPECIFICATION FOR MINERAL ABRASIVES INFORMATION SHEET 1491
• RELATIVE HUMIDITY – SUBSTRATE TEMPERATURE – AIR TEMPERATURE INFORMATION SHEET 1650
WARRANTY
PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPG’s specifications for such product in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any
third person for infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN
LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE, INCLUDING WITHOUT LIMITATION, ANY OTHER WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR USE, ARE DISCLAIMED BY PPG. Any claim under this
warranty must be made by Buyer to PPG in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life of the product, or one year from the date of the
delivery of the product to the Buyer, whichever is earlier. Buyer’s failure to notify PPG of such non-conformance as required herein shall bar Buyer from recovery under this warranty.
LIMITATIONS OF LIABILITY
IN NO EVENT WILL PPG BE LIABLE UNDER ANY THEORY OF RECOVERY (WHETHER BASED ON NEGLIGENCE OF ANY KIND, STRICT LIABILITY OR TORT) FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES IN ANY WAY RELATED TO, ARISING FROM, OR RESULTING FROM ANY USE MADE OF THE PRODUCT. The information in this sheet is intended for guidance only and is based upon laboratory tests that PPG believes to
be reliable. PPG may modify the information contained herein at any time as a result of practical experience and continuous product development. All recommendations or suggestions relating to the use of the PPG product, whether in
technical documentation, or in response to a specific inquiry, or otherwise, are based on data, which to the best of PPG’s knowledge, is reliable. The product and related information is designed for users having the requisite knowledge
and industrial skills in the industry and it is the end-user’s responsibility to determine the suitability of the product for its own particular use and it shall be deemed that Buyer has done so, as its sole discretion and risk. PPG has no
control over either the quality or condition of the substrate, or the many factors affecting the use and application of the product. Therefore, PPG does not accept any liability arising from any loss, injury or damage resulting from such
use or the contents of this information (unless there are written agreements stating otherwise). Variations in the application environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. This
sheet supersedes all previous versions and it is the Buyer’s responsibility to ensure that this information is current prior to using the product. Current sheets for all PPG Protective & Marine Coatings Products are maintained at
www.ppgpmc.com. The English text of this sheet shall prevail over any translation thereof.
The PPG Logo, Bringing innovation to the surface., and all other trademarks herein are property of the PPG group of companies.
Ref. 7459 Page 5/5
